linux/drivers/usb/serial/io_usbvend.h
Greg Kroah-Hartman 6ca98bc284 USB: serial: Remove redundant license text
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner.  So the extra GPL text wording
can be removed as it is no longer needed at all.

This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text.  And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.

No copyright headers or other non-license-description text was removed.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-11-04 11:55:38 +01:00

681 lines
28 KiB
C

// SPDX-License-Identifier: GPL-2.0+
/************************************************************************
*
* USBVEND.H Vendor-specific USB definitions
*
* NOTE: This must be kept in sync with the Edgeport firmware and
* must be kept backward-compatible with older firmware.
*
************************************************************************
*
* Copyright (C) 1998 Inside Out Networks, Inc.
*
************************************************************************/
#if !defined(_USBVEND_H)
#define _USBVEND_H
/************************************************************************
*
* D e f i n e s / T y p e d e f s
*
************************************************************************/
//
// Definitions of USB product IDs
//
#define USB_VENDOR_ID_ION 0x1608 // Our VID
#define USB_VENDOR_ID_TI 0x0451 // TI VID
#define USB_VENDOR_ID_AXIOHM 0x05D9 /* Axiohm VID */
//
// Definitions of USB product IDs (PID)
// We break the USB-defined PID into an OEM Id field (upper 6 bits)
// and a Device Id (bottom 10 bits). The Device Id defines what
// device this actually is regardless of what the OEM wants to
// call it.
//
// ION-device OEM IDs
#define ION_OEM_ID_ION 0 // 00h Inside Out Networks
#define ION_OEM_ID_NLYNX 1 // 01h NLynx Systems
#define ION_OEM_ID_GENERIC 2 // 02h Generic OEM
#define ION_OEM_ID_MAC 3 // 03h Mac Version
#define ION_OEM_ID_MEGAWOLF 4 // 04h Lupusb OEM Mac version (MegaWolf)
#define ION_OEM_ID_MULTITECH 5 // 05h Multitech Rapidports
#define ION_OEM_ID_AGILENT 6 // 06h AGILENT board
// ION-device Device IDs
// Product IDs - assigned to match middle digit of serial number (No longer true)
#define ION_DEVICE_ID_80251_NETCHIP 0x020 // This bit is set in the PID if this edgeport hardware$
// is based on the 80251+Netchip.
#define ION_DEVICE_ID_GENERATION_1 0x00 // Value for 930 based edgeports
#define ION_DEVICE_ID_GENERATION_2 0x01 // Value for 80251+Netchip.
#define ION_DEVICE_ID_GENERATION_3 0x02 // Value for Texas Instruments TUSB5052 chip
#define ION_DEVICE_ID_GENERATION_4 0x03 // Watchport Family of products
#define ION_GENERATION_MASK 0x03
#define ION_DEVICE_ID_HUB_MASK 0x0080 // This bit in the PID designates a HUB device
// for example 8C would be a 421 4 port hub
// and 8D would be a 2 port embedded hub
#define EDGEPORT_DEVICE_ID_MASK 0x0ff // Not including OEM or GENERATION fields
#define ION_DEVICE_ID_UNCONFIGURED_EDGE_DEVICE 0x000 // In manufacturing only
#define ION_DEVICE_ID_EDGEPORT_4 0x001 // Edgeport/4 RS232
#define ION_DEVICE_ID_EDGEPORT_8R 0x002 // Edgeport with RJ45 no Ring
#define ION_DEVICE_ID_RAPIDPORT_4 0x003 // Rapidport/4
#define ION_DEVICE_ID_EDGEPORT_4T 0x004 // Edgeport/4 RS232 for Telxon (aka "Fleetport")
#define ION_DEVICE_ID_EDGEPORT_2 0x005 // Edgeport/2 RS232
#define ION_DEVICE_ID_EDGEPORT_4I 0x006 // Edgeport/4 RS422
#define ION_DEVICE_ID_EDGEPORT_2I 0x007 // Edgeport/2 RS422/RS485
#define ION_DEVICE_ID_EDGEPORT_8RR 0x008 // Edgeport with RJ45 with Data and RTS/CTS only
// ION_DEVICE_ID_EDGEPORT_8_HANDBUILT 0x009 // Hand-built Edgeport/8 (Placeholder, used in middle digit of serial number only!)
// ION_DEVICE_ID_MULTIMODEM_4X56 0x00A // MultiTech version of RP/4 (Placeholder, used in middle digit of serial number only!)
#define ION_DEVICE_ID_EDGEPORT_PARALLEL_PORT 0x00B // Edgeport/(4)21 Parallel port (USS720)
#define ION_DEVICE_ID_EDGEPORT_421 0x00C // Edgeport/421 Hub+RS232+Parallel
#define ION_DEVICE_ID_EDGEPORT_21 0x00D // Edgeport/21 RS232+Parallel
#define ION_DEVICE_ID_EDGEPORT_8_DUAL_CPU 0x00E // Half of an Edgeport/8 (the kind with 2 EP/4s on 1 PCB)
#define ION_DEVICE_ID_EDGEPORT_8 0x00F // Edgeport/8 (single-CPU)
#define ION_DEVICE_ID_EDGEPORT_2_DIN 0x010 // Edgeport/2 RS232 with Apple DIN connector
#define ION_DEVICE_ID_EDGEPORT_4_DIN 0x011 // Edgeport/4 RS232 with Apple DIN connector
#define ION_DEVICE_ID_EDGEPORT_16_DUAL_CPU 0x012 // Half of an Edgeport/16 (the kind with 2 EP/8s)
#define ION_DEVICE_ID_EDGEPORT_COMPATIBLE 0x013 // Edgeport Compatible, for NCR, Axiohm etc. testing
#define ION_DEVICE_ID_EDGEPORT_8I 0x014 // Edgeport/8 RS422 (single-CPU)
#define ION_DEVICE_ID_EDGEPORT_1 0x015 // Edgeport/1 RS232
#define ION_DEVICE_ID_EPOS44 0x016 // Half of an EPOS/44 (TIUMP BASED)
#define ION_DEVICE_ID_EDGEPORT_42 0x017 // Edgeport/42
#define ION_DEVICE_ID_EDGEPORT_412_8 0x018 // Edgeport/412 8 port part
#define ION_DEVICE_ID_EDGEPORT_412_4 0x019 // Edgeport/412 4 port part
#define ION_DEVICE_ID_EDGEPORT_22I 0x01A // Edgeport/22I is an Edgeport/4 with ports 1&2 RS422 and ports 3&4 RS232
// Compact Form factor TI based devices 2c, 21c, 22c, 221c
#define ION_DEVICE_ID_EDGEPORT_2C 0x01B // Edgeport/2c is a TI based Edgeport/2 - Small I2c
#define ION_DEVICE_ID_EDGEPORT_221C 0x01C // Edgeport/221c is a TI based Edgeport/2 with lucent chip and
// 2 external hub ports - Large I2C
#define ION_DEVICE_ID_EDGEPORT_22C 0x01D // Edgeport/22c is a TI based Edgeport/2 with
// 2 external hub ports - Large I2C
#define ION_DEVICE_ID_EDGEPORT_21C 0x01E // Edgeport/21c is a TI based Edgeport/2 with lucent chip
// Small I2C
/*
* DANGER DANGER The 0x20 bit was used to indicate a 8251/netchip GEN 2 device.
* Since the MAC, Linux, and Optimal drivers still used the old code
* I suggest that you skip the 0x20 bit when creating new PIDs
*/
// Generation 3 devices -- 3410 based edgport/1 (256 byte I2C)
#define ION_DEVICE_ID_TI3410_EDGEPORT_1 0x040 // Edgeport/1 RS232
#define ION_DEVICE_ID_TI3410_EDGEPORT_1I 0x041 // Edgeport/1i- RS422 model
// Ti based software switchable RS232/RS422/RS485 devices
#define ION_DEVICE_ID_EDGEPORT_4S 0x042 // Edgeport/4s - software switchable model
#define ION_DEVICE_ID_EDGEPORT_8S 0x043 // Edgeport/8s - software switchable model
// Usb to Ethernet dongle
#define ION_DEVICE_ID_EDGEPORT_E 0x0E0 // Edgeport/E Usb to Ethernet
// Edgeport TI based devices
#define ION_DEVICE_ID_TI_EDGEPORT_4 0x0201 // Edgeport/4 RS232
#define ION_DEVICE_ID_TI_EDGEPORT_2 0x0205 // Edgeport/2 RS232
#define ION_DEVICE_ID_TI_EDGEPORT_4I 0x0206 // Edgeport/4i RS422
#define ION_DEVICE_ID_TI_EDGEPORT_2I 0x0207 // Edgeport/2i RS422/RS485
#define ION_DEVICE_ID_TI_EDGEPORT_421 0x020C // Edgeport/421 4 hub 2 RS232 + Parallel (lucent on a different hub port)
#define ION_DEVICE_ID_TI_EDGEPORT_21 0x020D // Edgeport/21 2 RS232 + Parallel (lucent on a different hub port)
#define ION_DEVICE_ID_TI_EDGEPORT_416 0x0212 // Edgeport/416
#define ION_DEVICE_ID_TI_EDGEPORT_1 0x0215 // Edgeport/1 RS232
#define ION_DEVICE_ID_TI_EDGEPORT_42 0x0217 // Edgeport/42 4 hub 2 RS232
#define ION_DEVICE_ID_TI_EDGEPORT_22I 0x021A // Edgeport/22I is an Edgeport/4 with ports 1&2 RS422 and ports 3&4 RS232
#define ION_DEVICE_ID_TI_EDGEPORT_2C 0x021B // Edgeport/2c RS232
#define ION_DEVICE_ID_TI_EDGEPORT_221C 0x021C // Edgeport/221c is a TI based Edgeport/2 with lucent chip and
// 2 external hub ports - Large I2C
#define ION_DEVICE_ID_TI_EDGEPORT_22C 0x021D // Edgeport/22c is a TI based Edgeport/2 with
// 2 external hub ports - Large I2C
#define ION_DEVICE_ID_TI_EDGEPORT_21C 0x021E // Edgeport/21c is a TI based Edgeport/2 with lucent chip
// Generation 3 devices -- 3410 based edgport/1 (256 byte I2C)
#define ION_DEVICE_ID_TI_TI3410_EDGEPORT_1 0x0240 // Edgeport/1 RS232
#define ION_DEVICE_ID_TI_TI3410_EDGEPORT_1I 0x0241 // Edgeport/1i- RS422 model
// Ti based software switchable RS232/RS422/RS485 devices
#define ION_DEVICE_ID_TI_EDGEPORT_4S 0x0242 // Edgeport/4s - software switchable model
#define ION_DEVICE_ID_TI_EDGEPORT_8S 0x0243 // Edgeport/8s - software switchable model
#define ION_DEVICE_ID_TI_EDGEPORT_8 0x0244 // Edgeport/8 (single-CPU)
#define ION_DEVICE_ID_TI_EDGEPORT_416B 0x0247 // Edgeport/416
/************************************************************************
*
* Generation 4 devices
*
************************************************************************/
// Watchport based on 3410 both 1-wire and binary products (16K I2C)
#define ION_DEVICE_ID_WP_UNSERIALIZED 0x300 // Watchport based on 3410 both 1-wire and binary products
#define ION_DEVICE_ID_WP_PROXIMITY 0x301 // Watchport/P Discontinued
#define ION_DEVICE_ID_WP_MOTION 0x302 // Watchport/M
#define ION_DEVICE_ID_WP_MOISTURE 0x303 // Watchport/W
#define ION_DEVICE_ID_WP_TEMPERATURE 0x304 // Watchport/T
#define ION_DEVICE_ID_WP_HUMIDITY 0x305 // Watchport/H
#define ION_DEVICE_ID_WP_POWER 0x306 // Watchport
#define ION_DEVICE_ID_WP_LIGHT 0x307 // Watchport
#define ION_DEVICE_ID_WP_RADIATION 0x308 // Watchport
#define ION_DEVICE_ID_WP_ACCELERATION 0x309 // Watchport/A
#define ION_DEVICE_ID_WP_DISTANCE 0x30A // Watchport/D Discontinued
#define ION_DEVICE_ID_WP_PROX_DIST 0x30B // Watchport/D uses distance sensor
// Default to /P function
#define ION_DEVICE_ID_PLUS_PWR_HP4CD 0x30C // 5052 Plus Power HubPort/4CD+ (for Dell)
#define ION_DEVICE_ID_PLUS_PWR_HP4C 0x30D // 5052 Plus Power HubPort/4C+
#define ION_DEVICE_ID_PLUS_PWR_PCI 0x30E // 3410 Plus Power PCI Host Controller 4 port
//
// Definitions for AXIOHM USB product IDs
//
#define USB_VENDOR_ID_AXIOHM 0x05D9 // Axiohm VID
#define AXIOHM_DEVICE_ID_MASK 0xffff
#define AXIOHM_DEVICE_ID_EPIC_A758 0xA758
#define AXIOHM_DEVICE_ID_EPIC_A794 0xA794
#define AXIOHM_DEVICE_ID_EPIC_A225 0xA225
//
// Definitions for NCR USB product IDs
//
#define USB_VENDOR_ID_NCR 0x0404 // NCR VID
#define NCR_DEVICE_ID_MASK 0xffff
#define NCR_DEVICE_ID_EPIC_0202 0x0202
#define NCR_DEVICE_ID_EPIC_0203 0x0203
#define NCR_DEVICE_ID_EPIC_0310 0x0310
#define NCR_DEVICE_ID_EPIC_0311 0x0311
#define NCR_DEVICE_ID_EPIC_0312 0x0312
//
// Definitions for SYMBOL USB product IDs
//
#define USB_VENDOR_ID_SYMBOL 0x05E0 // Symbol VID
#define SYMBOL_DEVICE_ID_MASK 0xffff
#define SYMBOL_DEVICE_ID_KEYFOB 0x0700
//
// Definitions for other product IDs
#define ION_DEVICE_ID_MT4X56USB 0x1403 // OEM device
#define GENERATION_ID_FROM_USB_PRODUCT_ID(ProductId) \
((__u16) ((ProductId >> 8) & (ION_GENERATION_MASK)))
#define MAKE_USB_PRODUCT_ID(OemId, DeviceId) \
((__u16) (((OemId) << 10) || (DeviceId)))
#define DEVICE_ID_FROM_USB_PRODUCT_ID(ProductId) \
((__u16) ((ProductId) & (EDGEPORT_DEVICE_ID_MASK)))
#define OEM_ID_FROM_USB_PRODUCT_ID(ProductId) \
((__u16) (((ProductId) >> 10) & 0x3F))
//
// Definitions of parameters for download code. Note that these are
// specific to a given version of download code and must change if the
// corresponding download code changes.
//
// TxCredits value below which driver won't bother sending (to prevent too many small writes).
// Send only if above 25%
#define EDGE_FW_GET_TX_CREDITS_SEND_THRESHOLD(InitialCredit, MaxPacketSize) (max(((InitialCredit) / 4), (MaxPacketSize)))
#define EDGE_FW_BULK_MAX_PACKET_SIZE 64 // Max Packet Size for Bulk In Endpoint (EP1)
#define EDGE_FW_BULK_READ_BUFFER_SIZE 1024 // Size to use for Bulk reads
#define EDGE_FW_INT_MAX_PACKET_SIZE 32 // Max Packet Size for Interrupt In Endpoint
// Note that many units were shipped with MPS=16, we
// force an upgrade to this value).
#define EDGE_FW_INT_INTERVAL 2 // 2ms polling on IntPipe
//
// Definitions of I/O Networks vendor-specific requests
// for default endpoint
//
// bmRequestType = 01000000 Set vendor-specific, to device
// bmRequestType = 11000000 Get vendor-specific, to device
//
// These are the definitions for the bRequest field for the
// above bmRequestTypes.
//
// For the read/write Edgeport memory commands, the parameters
// are as follows:
// wValue = 16-bit address
// wIndex = unused (though we could put segment 00: or FF: here)
// wLength = # bytes to read/write (max 64)
//
#define USB_REQUEST_ION_RESET_DEVICE 0 // Warm reboot Edgeport, retaining USB address
#define USB_REQUEST_ION_GET_EPIC_DESC 1 // Get Edgeport Compatibility Descriptor
// unused 2 // Unused, available
#define USB_REQUEST_ION_READ_RAM 3 // Read EdgePort RAM at specified addr
#define USB_REQUEST_ION_WRITE_RAM 4 // Write EdgePort RAM at specified addr
#define USB_REQUEST_ION_READ_ROM 5 // Read EdgePort ROM at specified addr
#define USB_REQUEST_ION_WRITE_ROM 6 // Write EdgePort ROM at specified addr
#define USB_REQUEST_ION_EXEC_DL_CODE 7 // Begin execution of RAM-based download
// code by jumping to address in wIndex:wValue
// 8 // Unused, available
#define USB_REQUEST_ION_ENABLE_SUSPEND 9 // Enable/Disable suspend feature
// (wValue != 0: Enable; wValue = 0: Disable)
#define USB_REQUEST_ION_SEND_IOSP 10 // Send an IOSP command to the edgeport over the control pipe
#define USB_REQUEST_ION_RECV_IOSP 11 // Receive an IOSP command from the edgeport over the control pipe
#define USB_REQUEST_ION_DIS_INT_TIMER 0x80 // Sent to Axiohm to enable/ disable
// interrupt token timer
// wValue = 1, enable (default)
// wValue = 0, disable
//
// Define parameter values for our vendor-specific commands
//
//
// Edgeport Compatibility Descriptor
//
// This descriptor is only returned by Edgeport-compatible devices
// supporting the EPiC spec. True ION devices do not return this
// descriptor, but instead return STALL on receipt of the
// GET_EPIC_DESC command. The driver interprets a STALL to mean that
// this is a "real" Edgeport.
//
struct edge_compatibility_bits {
// This __u32 defines which Vendor-specific commands/functionality
// the device supports on the default EP0 pipe.
__u32 VendEnableSuspend : 1; // 0001 Set if device supports ION_ENABLE_SUSPEND
__u32 VendUnused : 31; // Available for future expansion, must be 0
// This __u32 defines which IOSP commands are supported over the
// bulk pipe EP1.
// xxxx Set if device supports:
__u32 IOSPOpen : 1; // 0001 OPEN / OPEN_RSP (Currently must be 1)
__u32 IOSPClose : 1; // 0002 CLOSE
__u32 IOSPChase : 1; // 0004 CHASE / CHASE_RSP
__u32 IOSPSetRxFlow : 1; // 0008 SET_RX_FLOW
__u32 IOSPSetTxFlow : 1; // 0010 SET_TX_FLOW
__u32 IOSPSetXChar : 1; // 0020 SET_XON_CHAR/SET_XOFF_CHAR
__u32 IOSPRxCheck : 1; // 0040 RX_CHECK_REQ/RX_CHECK_RSP
__u32 IOSPSetClrBreak : 1; // 0080 SET_BREAK/CLEAR_BREAK
__u32 IOSPWriteMCR : 1; // 0100 MCR register writes (set/clr DTR/RTS)
__u32 IOSPWriteLCR : 1; // 0200 LCR register writes (wordlen/stop/parity)
__u32 IOSPSetBaudRate : 1; // 0400 setting Baud rate (writes to LCR.80h and DLL/DLM register)
__u32 IOSPDisableIntPipe : 1; // 0800 Do not use the interrupt pipe for TxCredits or RxButesAvailable
__u32 IOSPRxDataAvail : 1; // 1000 Return status of RX Fifo (Data available in Fifo)
__u32 IOSPTxPurge : 1; // 2000 Purge TXBuffer and/or Fifo in Edgeport hardware
__u32 IOSPUnused : 18; // Available for future expansion, must be 0
// This __u32 defines which 'general' features are supported
__u32 TrueEdgeport : 1; // 0001 Set if device is a 'real' Edgeport
// (Used only by driver, NEVER set by an EPiC device)
__u32 GenUnused : 31; // Available for future expansion, must be 0
};
#define EDGE_COMPATIBILITY_MASK0 0x0001
#define EDGE_COMPATIBILITY_MASK1 0x3FFF
#define EDGE_COMPATIBILITY_MASK2 0x0001
struct edge_compatibility_descriptor {
__u8 Length; // Descriptor Length (per USB spec)
__u8 DescType; // Descriptor Type (per USB spec, =DEVICE type)
__u8 EpicVer; // Version of EPiC spec supported
// (Currently must be 1)
__u8 NumPorts; // Number of serial ports supported
__u8 iDownloadFile; // Index of string containing download code filename
// 0=no download, FF=download compiled into driver.
__u8 Unused[3]; // Available for future expansion, must be 0
// (Currently must be 0).
__u8 MajorVersion; // Firmware version: xx.
__u8 MinorVersion; // yy.
__le16 BuildNumber; // zzzz (LE format)
// The following structure contains __u32s, with each bit
// specifying whether the EPiC device supports the given
// command or functionality.
struct edge_compatibility_bits Supports;
};
// Values for iDownloadFile
#define EDGE_DOWNLOAD_FILE_NONE 0 // No download requested
#define EDGE_DOWNLOAD_FILE_INTERNAL 0xFF // Download the file compiled into driver (930 version)
#define EDGE_DOWNLOAD_FILE_I930 0xFF // Download the file compiled into driver (930 version)
#define EDGE_DOWNLOAD_FILE_80251 0xFE // Download the file compiled into driver (80251 version)
/*
* Special addresses for READ/WRITE_RAM/ROM
*/
// Version 1 (original) format of DeviceParams
#define EDGE_MANUF_DESC_ADDR_V1 0x00FF7F00
#define EDGE_MANUF_DESC_LEN_V1 sizeof(EDGE_MANUF_DESCRIPTOR_V1)
// Version 2 format of DeviceParams. This format is longer (3C0h)
// and starts lower in memory, at the uppermost 1K in ROM.
#define EDGE_MANUF_DESC_ADDR 0x00FF7C00
#define EDGE_MANUF_DESC_LEN sizeof(struct edge_manuf_descriptor)
// Boot params descriptor
#define EDGE_BOOT_DESC_ADDR 0x00FF7FC0
#define EDGE_BOOT_DESC_LEN sizeof(struct edge_boot_descriptor)
// Define the max block size that may be read or written
// in a read/write RAM/ROM command.
#define MAX_SIZE_REQ_ION_READ_MEM ((__u16)64)
#define MAX_SIZE_REQ_ION_WRITE_MEM ((__u16)64)
//
// Notes for the following two ION vendor-specific param descriptors:
//
// 1. These have a standard USB descriptor header so they look like a
// normal descriptor.
// 2. Any strings in the structures are in USB-defined string
// descriptor format, so that they may be separately retrieved,
// if necessary, with a minimum of work on the 930. This also
// requires them to be in UNICODE format, which, for English at
// least, simply means extending each __u8 into a __u16.
// 3. For all fields, 00 means 'uninitialized'.
// 4. All unused areas should be set to 00 for future expansion.
//
// This structure is ver 2 format. It contains ALL USB descriptors as
// well as the configuration parameters that were in the original V1
// structure. It is NOT modified when new boot code is downloaded; rather,
// these values are set or modified by manufacturing. It is located at
// xC00-xFBF (length 3C0h) in the ROM.
// This structure is a superset of the v1 structure and is arranged so
// that all of the v1 fields remain at the same address. We are just
// adding more room to the front of the structure to hold the descriptors.
//
// The actual contents of this structure are defined in a 930 assembly
// file, converted to a binary image, and then written by the serialization
// program. The C definition of this structure just defines a dummy
// area for general USB descriptors and the descriptor tables (the root
// descriptor starts at xC00). At the bottom of the structure are the
// fields inherited from the v1 structure.
#define MAX_SERIALNUMBER_LEN 12
#define MAX_ASSEMBLYNUMBER_LEN 14
struct edge_manuf_descriptor {
__u16 RootDescTable[0x10]; // C00 Root of descriptor tables (just a placeholder)
__u8 DescriptorArea[0x2E0]; // C20 Descriptors go here, up to 2E0h (just a placeholder)
// Start of v1-compatible section
__u8 Length; // F00 Desc length for what follows, per USB (= C0h )
__u8 DescType; // F01 Desc type, per USB (=DEVICE type)
__u8 DescVer; // F02 Desc version/format (currently 2)
__u8 NumRootDescEntries; // F03 # entries in RootDescTable
__u8 RomSize; // F04 Size of ROM/E2PROM in K
__u8 RamSize; // F05 Size of external RAM in K
__u8 CpuRev; // F06 CPU revision level (chg only if s/w visible)
__u8 BoardRev; // F07 PCB revision level (chg only if s/w visible)
__u8 NumPorts; // F08 Number of ports
__u8 DescDate[3]; // F09 MM/DD/YY when descriptor template was compiler,
// so host can track changes to USB-only descriptors.
__u8 SerNumLength; // F0C USB string descriptor len
__u8 SerNumDescType; // F0D USB descriptor type (=STRING type)
__le16 SerialNumber[MAX_SERIALNUMBER_LEN]; // F0E "01-01-000100" Unicode Serial Number
__u8 AssemblyNumLength; // F26 USB string descriptor len
__u8 AssemblyNumDescType; // F27 USB descriptor type (=STRING type)
__le16 AssemblyNumber[MAX_ASSEMBLYNUMBER_LEN]; // F28 "350-1000-01-A " assembly number
__u8 OemAssyNumLength; // F44 USB string descriptor len
__u8 OemAssyNumDescType; // F45 USB descriptor type (=STRING type)
__le16 OemAssyNumber[MAX_ASSEMBLYNUMBER_LEN]; // F46 "xxxxxxxxxxxxxx" OEM assembly number
__u8 ManufDateLength; // F62 USB string descriptor len
__u8 ManufDateDescType; // F63 USB descriptor type (=STRING type)
__le16 ManufDate[6]; // F64 "MMDDYY" manufacturing date
__u8 Reserved3[0x4D]; // F70 -- unused, set to 0 --
__u8 UartType; // FBD Uart Type
__u8 IonPid; // FBE Product ID, == LSB of USB DevDesc.PID
// (Note: Edgeport/4s before 11/98 will have
// 00 here instead of 01)
__u8 IonConfig; // FBF Config byte for ION manufacturing use
// FBF end of structure, total len = 3C0h
};
#define MANUF_DESC_VER_1 1 // Original definition of MANUF_DESC
#define MANUF_DESC_VER_2 2 // Ver 2, starts at xC00h len 3C0h
// Uart Types
// Note: Since this field was added only recently, all Edgeport/4 units
// shipped before 11/98 will have 00 in this field. Therefore,
// both 00 and 01 values mean '654.
#define MANUF_UART_EXAR_654_EARLY 0 // Exar 16C654 in Edgeport/4s before 11/98
#define MANUF_UART_EXAR_654 1 // Exar 16C654
#define MANUF_UART_EXAR_2852 2 // Exar 16C2852
//
// Note: The CpuRev and BoardRev values do not conform to manufacturing
// revisions; they are to be incremented only when the CPU or hardware
// changes in a software-visible way, such that the 930 software or
// the host driver needs to handle the hardware differently.
//
// Values of bottom 5 bits of CpuRev & BoardRev for
// Implementation 0 (ie, 930-based)
#define MANUF_CPU_REV_AD4 1 // 930 AD4, with EP1 Rx bug (needs RXSPM)
#define MANUF_CPU_REV_AD5 2 // 930 AD5, with above bug (supposedly) fixed
#define MANUF_CPU_80251 0x20 // Intel 80251
#define MANUF_BOARD_REV_A 1 // Original version, == Manuf Rev A
#define MANUF_BOARD_REV_B 2 // Manuf Rev B, wakeup interrupt works
#define MANUF_BOARD_REV_C 3 // Manuf Rev C, 2/4 ports, rs232/rs422
#define MANUF_BOARD_REV_GENERATION_2 0x20 // Second generaiton edgeport
// Values of bottom 5 bits of CpuRev & BoardRev for
// Implementation 1 (ie, 251+Netchip-based)
#define MANUF_CPU_REV_1 1 // C251TB Rev 1 (Need actual Intel rev here)
#define MANUF_BOARD_REV_A 1 // First rev of 251+Netchip design
#define MANUF_SERNUM_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->SerialNumber)
#define MANUF_ASSYNUM_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->AssemblyNumber)
#define MANUF_OEMASSYNUM_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->OemAssyNumber)
#define MANUF_MANUFDATE_LENGTH sizeof(((struct edge_manuf_descriptor *)0)->ManufDate)
#define MANUF_ION_CONFIG_DIAG_NO_LOOP 0x20 // As below but no ext loopback test
#define MANUF_ION_CONFIG_DIAG 0x40 // 930 based device: 1=Run h/w diags, 0=norm
// TIUMP Device : 1=IONSERIAL needs to run Final Test
#define MANUF_ION_CONFIG_MASTER 0x80 // 930 based device: 1=Master mode, 0=Normal
// TIUMP Device : 1=First device on a multi TIUMP Device
//
// This structure describes parameters for the boot code, and
// is programmed along with new boot code. These are values
// which are specific to a given build of the boot code. It
// is exactly 64 bytes long and is fixed at address FF:xFC0
// - FF:xFFF. Note that the 930-mandated UCONFIG bytes are
// included in this structure.
//
struct edge_boot_descriptor {
__u8 Length; // C0 Desc length, per USB (= 40h)
__u8 DescType; // C1 Desc type, per USB (= DEVICE type)
__u8 DescVer; // C2 Desc version/format
__u8 Reserved1; // C3 -- unused, set to 0 --
__le16 BootCodeLength; // C4 Boot code goes from FF:0000 to FF:(len-1)
// (LE format)
__u8 MajorVersion; // C6 Firmware version: xx.
__u8 MinorVersion; // C7 yy.
__le16 BuildNumber; // C8 zzzz (LE format)
__u16 EnumRootDescTable; // CA Root of ROM-based descriptor table
__u8 NumDescTypes; // CC Number of supported descriptor types
__u8 Reserved4; // CD Fix Compiler Packing
__le16 Capabilities; // CE-CF Capabilities flags (LE format)
__u8 Reserved2[0x28]; // D0 -- unused, set to 0 --
__u8 UConfig0; // F8 930-defined CPU configuration byte 0
__u8 UConfig1; // F9 930-defined CPU configuration byte 1
__u8 Reserved3[6]; // FA -- unused, set to 0 --
// FF end of structure, total len = 80
};
#define BOOT_DESC_VER_1 1 // Original definition of BOOT_PARAMS
#define BOOT_DESC_VER_2 2 // 2nd definition, descriptors not included in boot
// Capabilities flags
#define BOOT_CAP_RESET_CMD 0x0001 // If set, boot correctly supports ION_RESET_DEVICE
/************************************************************************
T I U M P D E F I N I T I O N S
***********************************************************************/
// Chip definitions in I2C
#define UMP5152 0x52
#define UMP3410 0x10
//************************************************************************
// TI I2C Format Definitions
//************************************************************************
#define I2C_DESC_TYPE_INFO_BASIC 0x01
#define I2C_DESC_TYPE_FIRMWARE_BASIC 0x02
#define I2C_DESC_TYPE_DEVICE 0x03
#define I2C_DESC_TYPE_CONFIG 0x04
#define I2C_DESC_TYPE_STRING 0x05
#define I2C_DESC_TYPE_FIRMWARE_AUTO 0x07 // for 3410 download
#define I2C_DESC_TYPE_CONFIG_KLUDGE 0x14 // for 3410
#define I2C_DESC_TYPE_WATCHPORT_VERSION 0x15 // firmware version number for watchport
#define I2C_DESC_TYPE_WATCHPORT_CALIBRATION_DATA 0x16 // Watchport Calibration Data
#define I2C_DESC_TYPE_FIRMWARE_BLANK 0xf2
// Special section defined by ION
#define I2C_DESC_TYPE_ION 0 // Not defined by TI
struct ti_i2c_desc {
__u8 Type; // Type of descriptor
__le16 Size; // Size of data only not including header
__u8 CheckSum; // Checksum (8 bit sum of data only)
__u8 Data[0]; // Data starts here
} __attribute__((packed));
// for 5152 devices only (type 2 record)
// for 3410 the version is stored in the WATCHPORT_FIRMWARE_VERSION descriptor
struct ti_i2c_firmware_rec {
__u8 Ver_Major; // Firmware Major version number
__u8 Ver_Minor; // Firmware Minor version number
__u8 Data[0]; // Download starts here
} __attribute__((packed));
struct watchport_firmware_version {
// Added 2 bytes for version number
__u8 Version_Major; // Download Version (for Watchport)
__u8 Version_Minor;
} __attribute__((packed));
// Structure of header of download image in fw_down.h
struct ti_i2c_image_header {
__le16 Length;
__u8 CheckSum;
} __attribute__((packed));
struct ti_basic_descriptor {
__u8 Power; // Self powered
// bit 7: 1 - power switching supported
// 0 - power switching not supported
//
// bit 0: 1 - self powered
// 0 - bus powered
//
//
__u16 HubVid; // VID HUB
__u16 HubPid; // PID HUB
__u16 DevPid; // PID Edgeport
__u8 HubTime; // Time for power on to power good
__u8 HubCurrent; // HUB Current = 100ma
} __attribute__((packed));
// CPU / Board Rev Definitions
#define TI_CPU_REV_5052 2 // 5052 based edgeports
#define TI_CPU_REV_3410 3 // 3410 based edgeports
#define TI_BOARD_REV_TI_EP 0 // Basic ti based edgeport
#define TI_BOARD_REV_COMPACT 1 // Compact board
#define TI_BOARD_REV_WATCHPORT 2 // Watchport
#define TI_GET_CPU_REVISION(x) (__u8)((((x)>>4)&0x0f))
#define TI_GET_BOARD_REVISION(x) (__u8)(((x)&0x0f))
#define TI_I2C_SIZE_MASK 0x1f // 5 bits
#define TI_GET_I2C_SIZE(x) ((((x) & TI_I2C_SIZE_MASK)+1)*256)
#define TI_MAX_I2C_SIZE (16 * 1024)
#define TI_MANUF_VERSION_0 0
// IonConig2 flags
#define TI_CONFIG2_RS232 0x01
#define TI_CONFIG2_RS422 0x02
#define TI_CONFIG2_RS485 0x04
#define TI_CONFIG2_SWITCHABLE 0x08
#define TI_CONFIG2_WATCHPORT 0x10
struct edge_ti_manuf_descriptor {
__u8 IonConfig; // Config byte for ION manufacturing use
__u8 IonConfig2; // Expansion
__u8 Version; // Version
__u8 CpuRev_BoardRev; // CPU revision level (0xF0) and Board Rev Level (0x0F)
__u8 NumPorts; // Number of ports for this UMP
__u8 NumVirtualPorts; // Number of Virtual ports
__u8 HubConfig1; // Used to configure the Hub
__u8 HubConfig2; // Used to configure the Hub
__u8 TotalPorts; // Total Number of Com Ports for the entire device (All UMPs)
__u8 Reserved; // Reserved
} __attribute__((packed));
#endif // if !defined(_USBVEND_H)