linux/drivers/usb/otg/Kconfig
Valentin Longchamp dd091c7b32 USB: otg Kconfig: let USB_OTG_UTILS select USB_ULPI option
With CONFIG_USB_ULPI=y, CONFIG_USB<=m, CONFIG_PCI=n and
CONFIG_USB_OTG_UTILS=n, which is the default used for mx31moboard,
the build for all mx3 platforms fails because drivers/usb/otg/ulpi.c
where otg_ulpi_create is defined is not compiled.

Build error:
arch/arm/mach-mx3/built-in.o: In function `mxc_board_init':
kzmarm11.c:(.init.text+0x73c): undefined reference to `otg_ulpi_create'
kzmarm11.c:(.init.text+0x1020): undefined reference to `otg_ulpi_create'

This isn't a strong dependency as drivers/usb/otg/ulpi.c doesn't
use functions defined in drivers/usb/otg/otg.o and is only needed
to get ulpi.o linked into the kernel image.

Signed-off-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-02-16 15:11:09 -08:00

73 lines
2.1 KiB
Plaintext

#
# USB OTG infrastructure may be needed for peripheral-only, host-only,
# or OTG-capable configurations when OTG transceivers or controllers
# are used.
#
comment "OTG and related infrastructure"
config USB_OTG_UTILS
bool
help
Select this to make sure the build includes objects from
the OTG infrastructure directory.
if USB || USB_GADGET
#
# USB Transceiver Drivers
#
config USB_GPIO_VBUS
tristate "GPIO based peripheral-only VBUS sensing 'transceiver'"
depends on GENERIC_GPIO
select USB_OTG_UTILS
help
Provides simple GPIO VBUS sensing for controllers with an
internal transceiver via the otg_transceiver interface, and
optionally control of a D+ pullup GPIO as well as a VBUS
current limit regulator.
config ISP1301_OMAP
tristate "Philips ISP1301 with OMAP OTG"
depends on I2C && ARCH_OMAP_OTG
select USB_OTG_UTILS
help
If you say yes here you get support for the Philips ISP1301
USB-On-The-Go transceiver working with the OMAP OTG controller.
The ISP1301 is a full speed USB transceiver which is used in
products including H2, H3, and H4 development boards for Texas
Instruments OMAP processors.
This driver can also be built as a module. If so, the module
will be called isp1301_omap.
config USB_ULPI
bool "Generic ULPI Transceiver Driver"
depends on ARM
select USB_OTG_UTILS
help
Enable this to support ULPI connected USB OTG transceivers which
are likely found on embedded boards.
The only chip currently supported is NXP's ISP1504
config TWL4030_USB
tristate "TWL4030 USB Transceiver Driver"
depends on TWL4030_CORE && REGULATOR_TWL4030
select USB_OTG_UTILS
help
Enable this to support the USB OTG transceiver on TWL4030
family chips (including the TWL5030 and TPS659x0 devices).
This transceiver supports high and full speed devices plus,
in host mode, low speed.
config NOP_USB_XCEIV
tristate "NOP USB Transceiver Driver"
select USB_OTG_UTILS
help
this driver is to be used by all the usb transceiver which are either
built-in with usb ip or which are autonomous and doesn't require any
phy programming such as ISP1x04 etc.
endif # USB || OTG