linux/arch/mips/Kconfig
Jason Wessel 8854700115 [MIPS] kgdb: add arch support for the kernel's kgdb core
The new kgdb architecture specific handler registers and unregisters
dynamically for exceptions depending on when you configure a kgdb I/O
driver.

Aside from initializing the exceptions earlier in the boot process,
kgdb should have no impact on a device when it is compiled in so long
as an I/O module is not configured for use.

There have been quite a number of contributors during the existence of
this patch (see arch/mips/kernel/kgdb.c).  Most recently Jason
re-wrote the mips kgdb logic to use the die notification handlers.

Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2008-07-30 21:54:42 +01:00

2043 lines
47 KiB
Plaintext

config MIPS
bool
default y
select HAVE_IDE
select HAVE_OPROFILE
select HAVE_ARCH_KGDB
# Horrible source of confusion. Die, die, die ...
select EMBEDDED
select RTC_LIB
mainmenu "Linux/MIPS Kernel Configuration"
menu "Machine selection"
config ZONE_DMA
bool
choice
prompt "System type"
default SGI_IP22
config MACH_ALCHEMY
bool "Alchemy processor based machines"
config BASLER_EXCITE
bool "Basler eXcite smart camera"
select CEVT_R4K
select CSRC_R4K
select DMA_COHERENT
select HW_HAS_PCI
select IRQ_CPU
select IRQ_CPU_RM7K
select IRQ_CPU_RM9K
select MIPS_RM9122
select SYS_HAS_CPU_RM9000
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
help
The eXcite is a smart camera platform manufactured by
Basler Vision Technologies AG.
config BCM47XX
bool "BCM47XX based boards"
select CEVT_R4K
select CSRC_R4K
select DMA_NONCOHERENT
select HW_HAS_PCI
select IRQ_CPU
select SYS_HAS_CPU_MIPS32_R1
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_LITTLE_ENDIAN
select SSB
select SSB_DRIVER_MIPS
select SSB_DRIVER_EXTIF
select SSB_PCICORE_HOSTMODE if PCI
select GENERIC_GPIO
select SYS_HAS_EARLY_PRINTK
select CFE
help
Support for BCM47XX based boards
config MIPS_COBALT
bool "Cobalt Server"
select CEVT_R4K
select CSRC_R4K
select CEVT_GT641XX
select DMA_NONCOHERENT
select HW_HAS_PCI
select I8253
select I8259
select IRQ_CPU
select IRQ_GT641XX
select PCI_GT64XXX_PCI0
select SYS_HAS_CPU_NEVADA
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_LITTLE_ENDIAN
select GENERIC_HARDIRQS_NO__DO_IRQ
config MACH_DECSTATION
bool "DECstations"
select BOOT_ELF32
select CEVT_DS1287
select CEVT_R4K
select CSRC_IOASIC
select CSRC_R4K
select CPU_DADDI_WORKAROUNDS if 64BIT
select CPU_R4000_WORKAROUNDS if 64BIT
select CPU_R4400_WORKAROUNDS if 64BIT
select DMA_NONCOHERENT
select NO_IOPORT
select IRQ_CPU
select SYS_HAS_CPU_R3000
select SYS_HAS_CPU_R4X00
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_SUPPORTS_128HZ
select SYS_SUPPORTS_256HZ
select SYS_SUPPORTS_1024HZ
help
This enables support for DEC's MIPS based workstations. For details
see the Linux/MIPS FAQ on <http://www.linux-mips.org/> and the
DECstation porting pages on <http://decstation.unix-ag.org/>.
If you have one of the following DECstation Models you definitely
want to choose R4xx0 for the CPU Type:
DECstation 5000/50
DECstation 5000/150
DECstation 5000/260
DECsystem 5900/260
otherwise choose R3000.
config MACH_JAZZ
bool "Jazz family of machines"
select ARC
select ARC32
select ARCH_MAY_HAVE_PC_FDC
select CEVT_R4K
select CSRC_R4K
select DEFAULT_SGI_PARTITION if CPU_BIG_ENDIAN
select GENERIC_ISA_DMA
select IRQ_CPU
select I8253
select I8259
select ISA
select SYS_HAS_CPU_R4X00
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
select SYS_SUPPORTS_100HZ
select GENERIC_HARDIRQS_NO__DO_IRQ
help
This a family of machines based on the MIPS R4030 chipset which was
used by several vendors to build RISC/os and Windows NT workstations.
Members include the Acer PICA, MIPS Magnum 4000, MIPS Millenium and
Olivetti M700-10 workstations.
config LASAT
bool "LASAT Networks platforms"
select CEVT_R4K
select CSRC_R4K
select DMA_NONCOHERENT
select SYS_HAS_EARLY_PRINTK
select HW_HAS_PCI
select IRQ_CPU
select PCI_GT64XXX_PCI0
select MIPS_NILE4
select R5000_CPU_SCACHE
select SYS_HAS_CPU_R5000
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_64BIT_KERNEL if BROKEN
select SYS_SUPPORTS_LITTLE_ENDIAN
select GENERIC_HARDIRQS_NO__DO_IRQ
config LEMOTE_FULONG
bool "Lemote Fulong mini-PC"
select ARCH_SPARSEMEM_ENABLE
select CEVT_R4K
select CSRC_R4K
select SYS_HAS_CPU_LOONGSON2
select DMA_NONCOHERENT
select BOOT_ELF32
select BOARD_SCACHE
select HAVE_STD_PC_SERIAL_PORT
select HW_HAS_PCI
select I8259
select ISA
select IRQ_CPU
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_SUPPORTS_HIGHMEM
select SYS_HAS_EARLY_PRINTK
select GENERIC_HARDIRQS_NO__DO_IRQ
select GENERIC_ISA_DMA_SUPPORT_BROKEN
select CPU_HAS_WB
help
Lemote Fulong mini-PC board based on the Chinese Loongson-2E CPU and
an FPGA northbridge
config MIPS_MALTA
bool "MIPS Malta board"
select ARCH_MAY_HAVE_PC_FDC
select BOOT_ELF32
select BOOT_RAW
select CEVT_R4K
select CSRC_R4K
select DMA_NONCOHERENT
select GENERIC_ISA_DMA
select IRQ_CPU
select IRQ_GIC
select HW_HAS_PCI
select I8253
select I8259
select MIPS_BOARDS_GEN
select MIPS_BONITO64
select MIPS_CPU_SCACHE
select PCI_GT64XXX_PCI0
select MIPS_MSC
select SWAP_IO_SPACE
select SYS_HAS_CPU_MIPS32_R1
select SYS_HAS_CPU_MIPS32_R2
select SYS_HAS_CPU_MIPS64_R1
select SYS_HAS_CPU_NEVADA
select SYS_HAS_CPU_RM7000
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_SUPPORTS_MULTITHREADING
select SYS_SUPPORTS_SMARTMIPS
help
This enables support for the MIPS Technologies Malta evaluation
board.
config MIPS_SIM
bool 'MIPS simulator (MIPSsim)'
select CEVT_R4K
select CSRC_R4K
select DMA_NONCOHERENT
select SYS_HAS_EARLY_PRINTK
select IRQ_CPU
select BOOT_RAW
select SYS_HAS_CPU_MIPS32_R1
select SYS_HAS_CPU_MIPS32_R2
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_MULTITHREADING
select SYS_SUPPORTS_LITTLE_ENDIAN
help
This option enables support for MIPS Technologies MIPSsim software
emulator.
config MARKEINS
bool "NEC EMMA2RH Mark-eins"
select CEVT_R4K
select CSRC_R4K
select DMA_NONCOHERENT
select HW_HAS_PCI
select IRQ_CPU
select SWAP_IO_SPACE
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
select SYS_HAS_CPU_R5000
help
This enables support for the R5432-based NEC Mark-eins
boards with R5500 CPU.
config MACH_VR41XX
bool "NEC VR4100 series based machines"
select CEVT_R4K
select CSRC_R4K
select SYS_HAS_CPU_VR41XX
select GENERIC_HARDIRQS_NO__DO_IRQ
config PNX8550_JBS
bool "NXP PNX8550 based JBS board"
select PNX8550
select SYS_SUPPORTS_LITTLE_ENDIAN
config PNX8550_STB810
bool "NXP PNX8550 based STB810 board"
select PNX8550
select SYS_SUPPORTS_LITTLE_ENDIAN
config PMC_MSP
bool "PMC-Sierra MSP chipsets"
depends on EXPERIMENTAL
select DMA_NONCOHERENT
select SWAP_IO_SPACE
select NO_EXCEPT_FILL
select BOOT_RAW
select SYS_HAS_CPU_MIPS32_R1
select SYS_HAS_CPU_MIPS32_R2
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select IRQ_CPU
select SERIAL_8250
select SERIAL_8250_CONSOLE
help
This adds support for the PMC-Sierra family of Multi-Service
Processor System-On-A-Chips. These parts include a number
of integrated peripherals, interfaces and DSPs in addition to
a variety of MIPS cores.
config PMC_YOSEMITE
bool "PMC-Sierra Yosemite eval board"
select CEVT_R4K
select CSRC_R4K
select DMA_COHERENT
select HW_HAS_PCI
select IRQ_CPU
select IRQ_CPU_RM7K
select IRQ_CPU_RM9K
select SWAP_IO_SPACE
select SYS_HAS_CPU_RM9000
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_SMP
help
Yosemite is an evaluation board for the RM9000x2 processor
manufactured by PMC-Sierra.
config SGI_IP22
bool "SGI IP22 (Indy/Indigo2)"
select ARC
select ARC32
select BOOT_ELF32
select CEVT_R4K
select CSRC_R4K
select DEFAULT_SGI_PARTITION
select DMA_NONCOHERENT
select HW_HAS_EISA
select I8253
select I8259
select IP22_CPU_SCACHE
select IRQ_CPU
select GENERIC_ISA_DMA_SUPPORT_BROKEN
select SGI_HAS_DS1286
select SGI_HAS_I8042
select SGI_HAS_INDYDOG
select SGI_HAS_HAL2
select SGI_HAS_SEEQ
select SGI_HAS_WD93
select SGI_HAS_ZILOG
select SWAP_IO_SPACE
select SYS_HAS_CPU_R4X00
select SYS_HAS_CPU_R5000
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
help
This are the SGI Indy, Challenge S and Indigo2, as well as certain
OEM variants like the Tandem CMN B006S. To compile a Linux kernel
that runs on these, say Y here.
config SGI_IP27
bool "SGI IP27 (Origin200/2000)"
select ARC
select ARC64
select BOOT_ELF64
select DEFAULT_SGI_PARTITION
select DMA_IP27
select SYS_HAS_EARLY_PRINTK
select HW_HAS_PCI
select NR_CPUS_DEFAULT_64
select SYS_HAS_CPU_R10000
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_NUMA
select SYS_SUPPORTS_SMP
select GENERIC_HARDIRQS_NO__DO_IRQ
help
This are the SGI Origin 200, Origin 2000 and Onyx 2 Graphics
workstations. To compile a Linux kernel that runs on these, say Y
here.
config SGI_IP28
bool "SGI IP28 (Indigo2 R10k) (EXPERIMENTAL)"
depends on EXPERIMENTAL
select ARC
select ARC64
select BOOT_ELF64
select CEVT_R4K
select CSRC_R4K
select DEFAULT_SGI_PARTITION
select DMA_NONCOHERENT
select GENERIC_ISA_DMA_SUPPORT_BROKEN
select IRQ_CPU
select HW_HAS_EISA
select I8253
select I8259
select SGI_HAS_DS1286
select SGI_HAS_I8042
select SGI_HAS_INDYDOG
select SGI_HAS_HAL2
select SGI_HAS_SEEQ
select SGI_HAS_WD93
select SGI_HAS_ZILOG
select SWAP_IO_SPACE
select SYS_HAS_CPU_R10000
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
help
This is the SGI Indigo2 with R10000 processor. To compile a Linux
kernel that runs on these, say Y here.
config SGI_IP32
bool "SGI IP32 (O2)"
select ARC
select ARC32
select BOOT_ELF32
select CEVT_R4K
select CSRC_R4K
select DMA_NONCOHERENT
select HW_HAS_PCI
select IRQ_CPU
select R5000_CPU_SCACHE
select RM7000_CPU_SCACHE
select SYS_HAS_CPU_R5000
select SYS_HAS_CPU_R10000 if BROKEN
select SYS_HAS_CPU_RM7000
select SYS_HAS_CPU_NEVADA
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
help
If you want this kernel to run on SGI O2 workstation, say Y here.
config SIBYTE_CRHINE
bool "Sibyte BCM91120C-CRhine"
depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select SIBYTE_BCM1120
select SWAP_IO_SPACE
select SYS_HAS_CPU_SB1
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
config SIBYTE_CARMEL
bool "Sibyte BCM91120x-Carmel"
depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select SIBYTE_BCM1120
select SWAP_IO_SPACE
select SYS_HAS_CPU_SB1
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
config SIBYTE_CRHONE
bool "Sibyte BCM91125C-CRhone"
depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select SIBYTE_BCM1125
select SWAP_IO_SPACE
select SYS_HAS_CPU_SB1
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_LITTLE_ENDIAN
config SIBYTE_RHONE
bool "Sibyte BCM91125E-Rhone"
depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select SIBYTE_BCM1125H
select SWAP_IO_SPACE
select SYS_HAS_CPU_SB1
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
config SIBYTE_SWARM
bool "Sibyte BCM91250A-SWARM"
select BOOT_ELF32
select DMA_COHERENT
select NR_CPUS_DEFAULT_2
select SIBYTE_SB1250
select SWAP_IO_SPACE
select SYS_HAS_CPU_SB1
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_LITTLE_ENDIAN
select ZONE_DMA32 if 64BIT
config SIBYTE_LITTLESUR
bool "Sibyte BCM91250C2-LittleSur"
depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select NR_CPUS_DEFAULT_2
select SIBYTE_SB1250
select SWAP_IO_SPACE
select SYS_HAS_CPU_SB1
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_LITTLE_ENDIAN
config SIBYTE_SENTOSA
bool "Sibyte BCM91250E-Sentosa"
depends on EXPERIMENTAL
select BOOT_ELF32
select DMA_COHERENT
select NR_CPUS_DEFAULT_2
select SIBYTE_SB1250
select SWAP_IO_SPACE
select SYS_HAS_CPU_SB1
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
config SIBYTE_BIGSUR
bool "Sibyte BCM91480B-BigSur"
select BOOT_ELF32
select DMA_COHERENT
select NR_CPUS_DEFAULT_4
select SIBYTE_BCM1x80
select SWAP_IO_SPACE
select SYS_HAS_CPU_SB1
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_LITTLE_ENDIAN
select ZONE_DMA32 if 64BIT
config SNI_RM
bool "SNI RM200/300/400"
select ARC if CPU_LITTLE_ENDIAN
select ARC32 if CPU_LITTLE_ENDIAN
select SNIPROM if CPU_BIG_ENDIAN
select ARCH_MAY_HAVE_PC_FDC
select BOOT_ELF32
select CEVT_R4K
select CSRC_R4K
select DEFAULT_SGI_PARTITION if CPU_BIG_ENDIAN
select DMA_NONCOHERENT
select GENERIC_ISA_DMA
select HW_HAS_EISA
select HW_HAS_PCI
select IRQ_CPU
select I8253
select I8259
select ISA
select SWAP_IO_SPACE if CPU_BIG_ENDIAN
select SYS_HAS_CPU_R4X00
select SYS_HAS_CPU_R5000
select SYS_HAS_CPU_R10000
select R5000_CPU_SCACHE
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_64BIT_KERNEL if EXPERIMENTAL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_HIGHMEM
select SYS_SUPPORTS_LITTLE_ENDIAN
help
The SNI RM200/300/400 are MIPS-based machines manufactured by
Siemens Nixdorf Informationssysteme (SNI), parent company of Pyramid
Technology and now in turn merged with Fujitsu. Say Y here to
support this machine type.
config MACH_TX39XX
bool "Toshiba TX39 series based machines"
config MACH_TX49XX
bool "Toshiba TX49 series based machines"
config MIKROTIK_RB532
bool "Mikrotik RB532 boards"
select CEVT_R4K
select CSRC_R4K
select DMA_NONCOHERENT
select GENERIC_HARDIRQS_NO__DO_IRQ
select HW_HAS_PCI
select IRQ_CPU
select SYS_HAS_CPU_MIPS32_R1
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_LITTLE_ENDIAN
select SWAP_IO_SPACE
select BOOT_RAW
select GENERIC_GPIO
help
Support the Mikrotik(tm) RouterBoard 532 series,
based on the IDT RC32434 SoC.
config WR_PPMC
bool "Wind River PPMC board"
select CEVT_R4K
select CSRC_R4K
select IRQ_CPU
select BOOT_ELF32
select DMA_NONCOHERENT
select HW_HAS_PCI
select PCI_GT64XXX_PCI0
select SWAP_IO_SPACE
select SYS_HAS_CPU_MIPS32_R1
select SYS_HAS_CPU_MIPS32_R2
select SYS_HAS_CPU_MIPS64_R1
select SYS_HAS_CPU_NEVADA
select SYS_HAS_CPU_RM7000
select SYS_SUPPORTS_32BIT_KERNEL
select SYS_SUPPORTS_64BIT_KERNEL
select SYS_SUPPORTS_BIG_ENDIAN
select SYS_SUPPORTS_LITTLE_ENDIAN
help
This enables support for the Wind River MIPS32 4KC PPMC evaluation
board, which is based on GT64120 bridge chip.
endchoice
source "arch/mips/au1000/Kconfig"
source "arch/mips/basler/excite/Kconfig"
source "arch/mips/jazz/Kconfig"
source "arch/mips/lasat/Kconfig"
source "arch/mips/pmc-sierra/Kconfig"
source "arch/mips/sgi-ip27/Kconfig"
source "arch/mips/sibyte/Kconfig"
source "arch/mips/txx9/Kconfig"
source "arch/mips/vr41xx/Kconfig"
endmenu
config GENERIC_LOCKBREAK
bool
default y
depends on SMP && PREEMPT
config RWSEM_GENERIC_SPINLOCK
bool
default y
config RWSEM_XCHGADD_ALGORITHM
bool
config ARCH_HAS_ILOG2_U32
bool
default n
config ARCH_HAS_ILOG2_U64
bool
default n
config ARCH_SUPPORTS_OPROFILE
bool
default y if !MIPS_MT_SMTC
config GENERIC_FIND_NEXT_BIT
bool
default y
config GENERIC_HWEIGHT
bool
default y
config GENERIC_CALIBRATE_DELAY
bool
default y
config GENERIC_CLOCKEVENTS
bool
default y
config GENERIC_TIME
bool
default y
config GENERIC_CMOS_UPDATE
bool
default y
config SCHED_NO_NO_OMIT_FRAME_POINTER
bool
default y
config GENERIC_HARDIRQS_NO__DO_IRQ
bool
default n
#
# Select some configuration options automatically based on user selections.
#
config ARC
bool
config ARCH_MAY_HAVE_PC_FDC
bool
config BOOT_RAW
bool
config CEVT_BCM1480
bool
config CEVT_DS1287
bool
config CEVT_GT641XX
bool
config CEVT_R4K
bool
config CEVT_SB1250
bool
config CEVT_TXX9
bool
config CSRC_BCM1480
bool
config CSRC_IOASIC
bool
config CSRC_R4K
bool
config CSRC_SB1250
bool
config GPIO_TXX9
select GENERIC_GPIO
select ARCH_REQUIRE_GPIOLIB
bool
config CFE
bool
config DMA_COHERENT
bool
config DMA_IP27
bool
config DMA_NONCOHERENT
bool
select DMA_NEED_PCI_MAP_STATE
config DMA_NEED_PCI_MAP_STATE
bool
config EARLY_PRINTK
bool "Early printk" if EMBEDDED && DEBUG_KERNEL
depends on SYS_HAS_EARLY_PRINTK
default y
help
This option enables special console drivers which allow the kernel
to print messages very early in the bootup process.
This is useful for kernel debugging when your machine crashes very
early before the console code is initialized. For normal operation,
it is not recommended because it looks ugly on some machines and
doesn't cooperate with an X server. You should normally say N here,
unless you want to debug such a crash.
config SYS_HAS_EARLY_PRINTK
bool
config HOTPLUG_CPU
bool
default n
config I8259
bool
config MIPS_BONITO64
bool
config MIPS_MSC
bool
config MIPS_NILE4
bool
config MIPS_DISABLE_OBSOLETE_IDE
bool
config SYNC_R4K
bool
config NO_IOPORT
def_bool n
config GENERIC_ISA_DMA
bool
select ZONE_DMA if GENERIC_ISA_DMA_SUPPORT_BROKEN=n
config GENERIC_ISA_DMA_SUPPORT_BROKEN
bool
select GENERIC_ISA_DMA
config GENERIC_GPIO
bool
#
# Endianess selection. Sufficiently obscure so many users don't know what to
# answer,so we try hard to limit the available choices. Also the use of a
# choice statement should be more obvious to the user.
#
choice
prompt "Endianess selection"
help
Some MIPS machines can be configured for either little or big endian
byte order. These modes require different kernels and a different
Linux distribution. In general there is one preferred byteorder for a
particular system but some systems are just as commonly used in the
one or the other endianness.
config CPU_BIG_ENDIAN
bool "Big endian"
depends on SYS_SUPPORTS_BIG_ENDIAN
config CPU_LITTLE_ENDIAN
bool "Little endian"
depends on SYS_SUPPORTS_LITTLE_ENDIAN
help
endchoice
config SYS_SUPPORTS_APM_EMULATION
bool
config SYS_SUPPORTS_BIG_ENDIAN
bool
config SYS_SUPPORTS_LITTLE_ENDIAN
bool
config IRQ_CPU
bool
config IRQ_CPU_RM7K
bool
config IRQ_CPU_RM9K
bool
config IRQ_MSP_SLP
bool
config IRQ_MSP_CIC
bool
config IRQ_TXX9
bool
config IRQ_GT641XX
bool
config IRQ_GIC
bool
config MIPS_BOARDS_GEN
bool
config PCI_GT64XXX_PCI0
bool
config NO_EXCEPT_FILL
bool
config MIPS_RM9122
bool
select SERIAL_RM9000
config PNX8550
bool
select SOC_PNX8550
config SOC_PNX8550
bool
select DMA_NONCOHERENT
select HW_HAS_PCI
select SYS_HAS_CPU_MIPS32_R1
select SYS_HAS_EARLY_PRINTK
select SYS_SUPPORTS_32BIT_KERNEL
select GENERIC_HARDIRQS_NO__DO_IRQ
select GENERIC_GPIO
config SWAP_IO_SPACE
bool
config EMMA2RH
bool
depends on MARKEINS
default y
config SERIAL_RM9000
bool
config SGI_HAS_DS1286
bool
config SGI_HAS_INDYDOG
bool
config SGI_HAS_HAL2
bool
config SGI_HAS_SEEQ
bool
config SGI_HAS_WD93
bool
config SGI_HAS_ZILOG
bool
config SGI_HAS_I8042
bool
config DEFAULT_SGI_PARTITION
bool
config ARC32
bool
config SNIPROM
bool
config BOOT_ELF32
bool
config MIPS_L1_CACHE_SHIFT
int
default "4" if MACH_DECSTATION || MIKROTIK_RB532
default "7" if SGI_IP22 || SGI_IP27 || SGI_IP28 || SNI_RM
default "4" if PMC_MSP4200_EVAL
default "5"
config HAVE_STD_PC_SERIAL_PORT
bool
config ARC_CONSOLE
bool "ARC console support"
depends on SGI_IP22 || SGI_IP28 || (SNI_RM && CPU_LITTLE_ENDIAN)
config ARC_MEMORY
bool
depends on MACH_JAZZ || SNI_RM || SGI_IP32
default y
config ARC_PROMLIB
bool
depends on MACH_JAZZ || SNI_RM || SGI_IP22 || SGI_IP28 || SGI_IP32
default y
config ARC64
bool
config BOOT_ELF64
bool
menu "CPU selection"
choice
prompt "CPU type"
default CPU_R4X00
config CPU_LOONGSON2
bool "Loongson 2"
depends on SYS_HAS_CPU_LOONGSON2
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
select CPU_SUPPORTS_HIGHMEM
help
The Loongson 2E processor implements the MIPS III instruction set
with many extensions.
config CPU_MIPS32_R1
bool "MIPS32 Release 1"
depends on SYS_HAS_CPU_MIPS32_R1
select CPU_HAS_LLSC
select CPU_HAS_PREFETCH
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_HIGHMEM
help
Choose this option to build a kernel for release 1 or later of the
MIPS32 architecture. Most modern embedded systems with a 32-bit
MIPS processor are based on a MIPS32 processor. If you know the
specific type of processor in your system, choose those that one
otherwise CPU_MIPS32_R1 is a safe bet for any MIPS32 system.
Release 2 of the MIPS32 architecture is available since several
years so chances are you even have a MIPS32 Release 2 processor
in which case you should choose CPU_MIPS32_R2 instead for better
performance.
config CPU_MIPS32_R2
bool "MIPS32 Release 2"
depends on SYS_HAS_CPU_MIPS32_R2
select CPU_HAS_LLSC
select CPU_HAS_PREFETCH
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_HIGHMEM
help
Choose this option to build a kernel for release 2 or later of the
MIPS32 architecture. Most modern embedded systems with a 32-bit
MIPS processor are based on a MIPS32 processor. If you know the
specific type of processor in your system, choose those that one
otherwise CPU_MIPS32_R1 is a safe bet for any MIPS32 system.
config CPU_MIPS64_R1
bool "MIPS64 Release 1"
depends on SYS_HAS_CPU_MIPS64_R1
select CPU_HAS_LLSC
select CPU_HAS_PREFETCH
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
select CPU_SUPPORTS_HIGHMEM
help
Choose this option to build a kernel for release 1 or later of the
MIPS64 architecture. Many modern embedded systems with a 64-bit
MIPS processor are based on a MIPS64 processor. If you know the
specific type of processor in your system, choose those that one
otherwise CPU_MIPS64_R1 is a safe bet for any MIPS64 system.
Release 2 of the MIPS64 architecture is available since several
years so chances are you even have a MIPS64 Release 2 processor
in which case you should choose CPU_MIPS64_R2 instead for better
performance.
config CPU_MIPS64_R2
bool "MIPS64 Release 2"
depends on SYS_HAS_CPU_MIPS64_R2
select CPU_HAS_LLSC
select CPU_HAS_PREFETCH
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
select CPU_SUPPORTS_HIGHMEM
help
Choose this option to build a kernel for release 2 or later of the
MIPS64 architecture. Many modern embedded systems with a 64-bit
MIPS processor are based on a MIPS64 processor. If you know the
specific type of processor in your system, choose those that one
otherwise CPU_MIPS64_R1 is a safe bet for any MIPS64 system.
config CPU_R3000
bool "R3000"
depends on SYS_HAS_CPU_R3000
select CPU_HAS_WB
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_HIGHMEM
help
Please make sure to pick the right CPU type. Linux/MIPS is not
designed to be generic, i.e. Kernels compiled for R3000 CPUs will
*not* work on R4000 machines and vice versa. However, since most
of the supported machines have an R4000 (or similar) CPU, R4x00
might be a safe bet. If the resulting kernel does not work,
try to recompile with R3000.
config CPU_TX39XX
bool "R39XX"
depends on SYS_HAS_CPU_TX39XX
select CPU_SUPPORTS_32BIT_KERNEL
config CPU_VR41XX
bool "R41xx"
depends on SYS_HAS_CPU_VR41XX
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
help
The options selects support for the NEC VR4100 series of processors.
Only choose this option if you have one of these processors as a
kernel built with this option will not run on any other type of
processor or vice versa.
config CPU_R4300
bool "R4300"
depends on SYS_HAS_CPU_R4300
select CPU_HAS_LLSC
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
help
MIPS Technologies R4300-series processors.
config CPU_R4X00
bool "R4x00"
depends on SYS_HAS_CPU_R4X00
select CPU_HAS_LLSC
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
help
MIPS Technologies R4000-series processors other than 4300, including
the R4000, R4400, R4600, and 4700.
config CPU_TX49XX
bool "R49XX"
depends on SYS_HAS_CPU_TX49XX
select CPU_HAS_LLSC
select CPU_HAS_PREFETCH
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
config CPU_R5000
bool "R5000"
depends on SYS_HAS_CPU_R5000
select CPU_HAS_LLSC
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
help
MIPS Technologies R5000-series processors other than the Nevada.
config CPU_R5432
bool "R5432"
depends on SYS_HAS_CPU_R5432
select CPU_HAS_LLSC
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
config CPU_R6000
bool "R6000"
depends on EXPERIMENTAL
select CPU_HAS_LLSC
depends on SYS_HAS_CPU_R6000
select CPU_SUPPORTS_32BIT_KERNEL
help
MIPS Technologies R6000 and R6000A series processors. Note these
processors are extremely rare and the support for them is incomplete.
config CPU_NEVADA
bool "RM52xx"
depends on SYS_HAS_CPU_NEVADA
select CPU_HAS_LLSC
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
help
QED / PMC-Sierra RM52xx-series ("Nevada") processors.
config CPU_R8000
bool "R8000"
depends on EXPERIMENTAL
depends on SYS_HAS_CPU_R8000
select CPU_HAS_LLSC
select CPU_HAS_PREFETCH
select CPU_SUPPORTS_64BIT_KERNEL
help
MIPS Technologies R8000 processors. Note these processors are
uncommon and the support for them is incomplete.
config CPU_R10000
bool "R10000"
depends on SYS_HAS_CPU_R10000
select CPU_HAS_LLSC
select CPU_HAS_PREFETCH
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
select CPU_SUPPORTS_HIGHMEM
help
MIPS Technologies R10000-series processors.
config CPU_RM7000
bool "RM7000"
depends on SYS_HAS_CPU_RM7000
select CPU_HAS_LLSC
select CPU_HAS_PREFETCH
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
select CPU_SUPPORTS_HIGHMEM
config CPU_RM9000
bool "RM9000"
depends on SYS_HAS_CPU_RM9000
select CPU_HAS_LLSC
select CPU_HAS_PREFETCH
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
select CPU_SUPPORTS_HIGHMEM
select WEAK_ORDERING
config CPU_SB1
bool "SB1"
depends on SYS_HAS_CPU_SB1
select CPU_HAS_LLSC
select CPU_SUPPORTS_32BIT_KERNEL
select CPU_SUPPORTS_64BIT_KERNEL
select CPU_SUPPORTS_HIGHMEM
select WEAK_ORDERING
endchoice
config SYS_HAS_CPU_LOONGSON2
bool
config SYS_HAS_CPU_MIPS32_R1
bool
config SYS_HAS_CPU_MIPS32_R2
bool
config SYS_HAS_CPU_MIPS64_R1
bool
config SYS_HAS_CPU_MIPS64_R2
bool
config SYS_HAS_CPU_R3000
bool
config SYS_HAS_CPU_TX39XX
bool
config SYS_HAS_CPU_VR41XX
bool
config SYS_HAS_CPU_R4300
bool
config SYS_HAS_CPU_R4X00
bool
config SYS_HAS_CPU_TX49XX
bool
config SYS_HAS_CPU_R5000
bool
config SYS_HAS_CPU_R5432
bool
config SYS_HAS_CPU_R6000
bool
config SYS_HAS_CPU_NEVADA
bool
config SYS_HAS_CPU_R8000
bool
config SYS_HAS_CPU_R10000
bool
config SYS_HAS_CPU_RM7000
bool
config SYS_HAS_CPU_RM9000
bool
config SYS_HAS_CPU_SB1
bool
#
# CPU may reorder R->R, R->W, W->R, W->W
# Reordering beyond LL and SC is handled in WEAK_REORDERING_BEYOND_LLSC
#
config WEAK_ORDERING
bool
#
# CPU may reorder reads and writes beyond LL/SC
# CPU may reorder R->LL, R->LL, W->LL, W->LL, R->SC, R->SC, W->SC, W->SC
#
config WEAK_REORDERING_BEYOND_LLSC
bool
endmenu
#
# These two indicate any level of the MIPS32 and MIPS64 architecture
#
config CPU_MIPS32
bool
default y if CPU_MIPS32_R1 || CPU_MIPS32_R2
config CPU_MIPS64
bool
default y if CPU_MIPS64_R1 || CPU_MIPS64_R2
#
# These two indicate the revision of the architecture, either Release 1 or Release 2
#
config CPU_MIPSR1
bool
default y if CPU_MIPS32_R1 || CPU_MIPS64_R1
config CPU_MIPSR2
bool
default y if CPU_MIPS32_R2 || CPU_MIPS64_R2
config SYS_SUPPORTS_32BIT_KERNEL
bool
config SYS_SUPPORTS_64BIT_KERNEL
bool
config CPU_SUPPORTS_32BIT_KERNEL
bool
config CPU_SUPPORTS_64BIT_KERNEL
bool
menu "Kernel type"
choice
prompt "Kernel code model"
help
You should only select this option if you have a workload that
actually benefits from 64-bit processing or if your machine has
large memory. You will only be presented a single option in this
menu if your system does not support both 32-bit and 64-bit kernels.
config 32BIT
bool "32-bit kernel"
depends on CPU_SUPPORTS_32BIT_KERNEL && SYS_SUPPORTS_32BIT_KERNEL
select TRAD_SIGNALS
help
Select this option if you want to build a 32-bit kernel.
config 64BIT
bool "64-bit kernel"
depends on CPU_SUPPORTS_64BIT_KERNEL && SYS_SUPPORTS_64BIT_KERNEL
help
Select this option if you want to build a 64-bit kernel.
endchoice
choice
prompt "Kernel page size"
default PAGE_SIZE_4KB
config PAGE_SIZE_4KB
bool "4kB"
help
This option select the standard 4kB Linux page size. On some
R3000-family processors this is the only available page size. Using
4kB page size will minimize memory consumption and is therefore
recommended for low memory systems.
config PAGE_SIZE_8KB
bool "8kB"
depends on EXPERIMENTAL && CPU_R8000
help
Using 8kB page size will result in higher performance kernel at
the price of higher memory consumption. This option is available
only on the R8000 processor. Not that at the time of this writing
this option is still high experimental; there are also issues with
compatibility of user applications.
config PAGE_SIZE_16KB
bool "16kB"
depends on !CPU_R3000 && !CPU_TX39XX
help
Using 16kB page size will result in higher performance kernel at
the price of higher memory consumption. This option is available on
all non-R3000 family processors. Note that you will need a suitable
Linux distribution to support this.
config PAGE_SIZE_64KB
bool "64kB"
depends on EXPERIMENTAL && !CPU_R3000 && !CPU_TX39XX
help
Using 64kB page size will result in higher performance kernel at
the price of higher memory consumption. This option is available on
all non-R3000 family processor. Not that at the time of this
writing this option is still high experimental.
endchoice
config BOARD_SCACHE
bool
config IP22_CPU_SCACHE
bool
select BOARD_SCACHE
#
# Support for a MIPS32 / MIPS64 style S-caches
#
config MIPS_CPU_SCACHE
bool
select BOARD_SCACHE
config R5000_CPU_SCACHE
bool
select BOARD_SCACHE
config RM7000_CPU_SCACHE
bool
select BOARD_SCACHE
config SIBYTE_DMA_PAGEOPS
bool "Use DMA to clear/copy pages"
depends on CPU_SB1
help
Instead of using the CPU to zero and copy pages, use a Data Mover
channel. These DMA channels are otherwise unused by the standard
SiByte Linux port. Seems to give a small performance benefit.
config CPU_HAS_PREFETCH
bool
choice
prompt "MIPS MT options"
config MIPS_MT_DISABLED
bool "Disable multithreading support."
help
Use this option if your workload can't take advantage of
MIPS hardware multithreading support. On systems that don't have
the option of an MT-enabled processor this option will be the only
option in this menu.
config MIPS_MT_SMP
bool "Use 1 TC on each available VPE for SMP"
depends on SYS_SUPPORTS_MULTITHREADING
select CPU_MIPSR2_IRQ_VI
select CPU_MIPSR2_IRQ_EI
select MIPS_MT
select NR_CPUS_DEFAULT_2
select SMP
select SYS_SUPPORTS_SCHED_SMT if SMP
select SYS_SUPPORTS_SMP
select SMP_UP
help
This is a kernel model which is also known a VSMP or lately
has been marketesed into SMVP.
config MIPS_MT_SMTC
bool "SMTC: Use all TCs on all VPEs for SMP"
depends on CPU_MIPS32_R2
#depends on CPU_MIPS64_R2 # once there is hardware ...
depends on SYS_SUPPORTS_MULTITHREADING
select GENERIC_CLOCKEVENTS_BROADCAST
select CPU_MIPSR2_IRQ_VI
select CPU_MIPSR2_IRQ_EI
select MIPS_MT
select NR_CPUS_DEFAULT_8
select SMP
select SYS_SUPPORTS_SMP
select SMP_UP
help
This is a kernel model which is known a SMTC or lately has been
marketesed into SMVP.
endchoice
config MIPS_MT
bool
config SCHED_SMT
bool "SMT (multithreading) scheduler support"
depends on SYS_SUPPORTS_SCHED_SMT
default n
help
SMT scheduler support improves the CPU scheduler's decision making
when dealing with MIPS MT enabled cores at a cost of slightly
increased overhead in some places. If unsure say N here.
config SYS_SUPPORTS_SCHED_SMT
bool
config SYS_SUPPORTS_MULTITHREADING
bool
config MIPS_MT_FPAFF
bool "Dynamic FPU affinity for FP-intensive threads"
default y
depends on MIPS_MT_SMP || MIPS_MT_SMTC
config MIPS_VPE_LOADER
bool "VPE loader support."
depends on SYS_SUPPORTS_MULTITHREADING
select CPU_MIPSR2_IRQ_VI
select CPU_MIPSR2_IRQ_EI
select MIPS_MT
help
Includes a loader for loading an elf relocatable object
onto another VPE and running it.
config MIPS_MT_SMTC_INSTANT_REPLAY
bool "Low-latency Dispatch of Deferred SMTC IPIs"
depends on MIPS_MT_SMTC && !PREEMPT
default y
help
SMTC pseudo-interrupts between TCs are deferred and queued
if the target TC is interrupt-inhibited (IXMT). In the first
SMTC prototypes, these queued IPIs were serviced on return
to user mode, or on entry into the kernel idle loop. The
INSTANT_REPLAY option dispatches them as part of local_irq_restore()
processing, which adds runtime overhead (hence the option to turn
it off), but ensures that IPIs are handled promptly even under
heavy I/O interrupt load.
config MIPS_MT_SMTC_IM_BACKSTOP
bool "Use per-TC register bits as backstop for inhibited IM bits"
depends on MIPS_MT_SMTC
default y
help
To support multiple TC microthreads acting as "CPUs" within
a VPE, VPE-wide interrupt mask bits must be specially manipulated
during interrupt handling. To support legacy drivers and interrupt
controller management code, SMTC has a "backstop" to track and
if necessary restore the interrupt mask. This has some performance
impact on interrupt service overhead. Disable it only if you know
what you are doing.
config MIPS_MT_SMTC_IRQAFF
bool "Support IRQ affinity API"
depends on MIPS_MT_SMTC
default n
help
Enables SMP IRQ affinity API (/proc/irq/*/smp_affinity, etc.)
for SMTC Linux kernel. Requires platform support, of which
an example can be found in the MIPS kernel i8259 and Malta
platform code. It is recommended that MIPS_MT_SMTC_INSTANT_REPLAY
be enabled if MIPS_MT_SMTC_IRQAFF is used. Adds overhead to
interrupt dispatch, and should be used only if you know what
you are doing.
config MIPS_VPE_LOADER_TOM
bool "Load VPE program into memory hidden from linux"
depends on MIPS_VPE_LOADER
default y
help
The loader can use memory that is present but has been hidden from
Linux using the kernel command line option "mem=xxMB". It's up to
you to ensure the amount you put in the option and the space your
program requires is less or equal to the amount physically present.
# this should possibly be in drivers/char, but it is rather cpu related. Hmmm
config MIPS_VPE_APSP_API
bool "Enable support for AP/SP API (RTLX)"
depends on MIPS_VPE_LOADER
help
config MIPS_APSP_KSPD
bool "Enable KSPD"
depends on MIPS_VPE_APSP_API
default y
help
KSPD is a kernel daemon that accepts syscall requests from the SP
side, actions them and returns the results. It also handles the
"exit" syscall notifying other kernel modules the SP program is
exiting. You probably want to say yes here.
config SB1_PASS_1_WORKAROUNDS
bool
depends on CPU_SB1_PASS_1
default y
config SB1_PASS_2_WORKAROUNDS
bool
depends on CPU_SB1 && (CPU_SB1_PASS_2_2 || CPU_SB1_PASS_2)
default y
config SB1_PASS_2_1_WORKAROUNDS
bool
depends on CPU_SB1 && CPU_SB1_PASS_2
default y
config 64BIT_PHYS_ADDR
bool
config CPU_HAS_LLSC
bool
config CPU_HAS_SMARTMIPS
depends on SYS_SUPPORTS_SMARTMIPS
bool "Support for the SmartMIPS ASE"
help
SmartMIPS is a extension of the MIPS32 architecture aimed at
increased security at both hardware and software level for
smartcards. Enabling this option will allow proper use of the
SmartMIPS instructions by Linux applications. However a kernel with
this option will not work on a MIPS core without SmartMIPS core. If
you don't know you probably don't have SmartMIPS and should say N
here.
config CPU_HAS_WB
bool
#
# Vectored interrupt mode is an R2 feature
#
config CPU_MIPSR2_IRQ_VI
bool
#
# Extended interrupt mode is an R2 feature
#
config CPU_MIPSR2_IRQ_EI
bool
config CPU_HAS_SYNC
bool
depends on !CPU_R3000
default y
config GENERIC_CLOCKEVENTS_BROADCAST
bool
#
# CPU non-features
#
config CPU_DADDI_WORKAROUNDS
bool
config CPU_R4000_WORKAROUNDS
bool
select CPU_R4400_WORKAROUNDS
config CPU_R4400_WORKAROUNDS
bool
#
# Use the generic interrupt handling code in kernel/irq/:
#
config GENERIC_HARDIRQS
bool
default y
config GENERIC_IRQ_PROBE
bool
default y
config IRQ_PER_CPU
bool
#
# - Highmem only makes sense for the 32-bit kernel.
# - The current highmem code will only work properly on physically indexed
# caches such as R3000, SB1, R7000 or those that look like they're virtually
# indexed such as R4000/R4400 SC and MC versions or R10000. So for the
# moment we protect the user and offer the highmem option only on machines
# where it's known to be safe. This will not offer highmem on a few systems
# such as MIPS32 and MIPS64 CPUs which may have virtual and physically
# indexed CPUs but we're playing safe.
# - We use SYS_SUPPORTS_HIGHMEM to offer highmem only for systems where we
# know they might have memory configurations that could make use of highmem
# support.
#
config HIGHMEM
bool "High Memory Support"
depends on 32BIT && CPU_SUPPORTS_HIGHMEM && SYS_SUPPORTS_HIGHMEM
config CPU_SUPPORTS_HIGHMEM
bool
config SYS_SUPPORTS_HIGHMEM
bool
config SYS_SUPPORTS_SMARTMIPS
bool
config ARCH_FLATMEM_ENABLE
def_bool y
depends on !NUMA
config ARCH_DISCONTIGMEM_ENABLE
bool
default y if SGI_IP27
help
Say Y to support efficient handling of discontiguous physical memory,
for architectures which are either NUMA (Non-Uniform Memory Access)
or have huge holes in the physical address space for other reasons.
See <file:Documentation/vm/numa> for more.
config ARCH_POPULATES_NODE_MAP
def_bool y
config ARCH_SPARSEMEM_ENABLE
bool
select SPARSEMEM_STATIC
config NUMA
bool "NUMA Support"
depends on SYS_SUPPORTS_NUMA
help
Say Y to compile the kernel to support NUMA (Non-Uniform Memory
Access). This option improves performance on systems with more
than two nodes; on two node systems it is generally better to
leave it disabled; on single node systems disable this option
disabled.
config SYS_SUPPORTS_NUMA
bool
config NODES_SHIFT
int
default "6"
depends on NEED_MULTIPLE_NODES
source "mm/Kconfig"
config SMP
bool "Multi-Processing support"
depends on SYS_SUPPORTS_SMP
select IRQ_PER_CPU
select USE_GENERIC_SMP_HELPERS
help
This enables support for systems with more than one CPU. If you have
a system with only one CPU, like most personal computers, say N. If
you have a system with more than one CPU, say Y.
If you say N here, the kernel will run on single and multiprocessor
machines, but will use only one CPU of a multiprocessor machine. If
you say Y here, the kernel will run on many, but not all,
singleprocessor machines. On a singleprocessor machine, the kernel
will run faster if you say N here.
People using multiprocessor machines who say Y here should also say
Y to "Enhanced Real Time Clock Support", below.
See also the SMP-HOWTO available at
<http://www.tldp.org/docs.html#howto>.
If you don't know what to do here, say N.
config SMP_UP
bool
config SYS_SUPPORTS_SMP
bool
config NR_CPUS_DEFAULT_1
bool
config NR_CPUS_DEFAULT_2
bool
config NR_CPUS_DEFAULT_4
bool
config NR_CPUS_DEFAULT_8
bool
config NR_CPUS_DEFAULT_16
bool
config NR_CPUS_DEFAULT_32
bool
config NR_CPUS_DEFAULT_64
bool
config NR_CPUS
int "Maximum number of CPUs (2-64)"
range 1 64 if NR_CPUS_DEFAULT_1
depends on SMP
default "1" if NR_CPUS_DEFAULT_1
default "2" if NR_CPUS_DEFAULT_2
default "4" if NR_CPUS_DEFAULT_4
default "8" if NR_CPUS_DEFAULT_8
default "16" if NR_CPUS_DEFAULT_16
default "32" if NR_CPUS_DEFAULT_32
default "64" if NR_CPUS_DEFAULT_64
help
This allows you to specify the maximum number of CPUs which this
kernel will support. The maximum supported value is 32 for 32-bit
kernel and 64 for 64-bit kernels; the minimum value which makes
sense is 1 for Qemu (useful only for kernel debugging purposes)
and 2 for all others.
This is purely to save memory - each supported CPU adds
approximately eight kilobytes to the kernel image. For best
performance should round up your number of processors to the next
power of two.
config MIPS_CMP
bool "MIPS CMP framework support"
depends on SMP
select SYNC_R4K
select SYS_SUPPORTS_SCHED_SMT
select WEAK_ORDERING
default n
help
This is a placeholder option for the GCMP work. It will need to
be handled differently...
source "kernel/time/Kconfig"
#
# Timer Interrupt Frequency Configuration
#
choice
prompt "Timer frequency"
default HZ_250
help
Allows the configuration of the timer frequency.
config HZ_48
bool "48 HZ" if SYS_SUPPORTS_48HZ || SYS_SUPPORTS_ARBIT_HZ
config HZ_100
bool "100 HZ" if SYS_SUPPORTS_100HZ || SYS_SUPPORTS_ARBIT_HZ
config HZ_128
bool "128 HZ" if SYS_SUPPORTS_128HZ || SYS_SUPPORTS_ARBIT_HZ
config HZ_250
bool "250 HZ" if SYS_SUPPORTS_250HZ || SYS_SUPPORTS_ARBIT_HZ
config HZ_256
bool "256 HZ" if SYS_SUPPORTS_256HZ || SYS_SUPPORTS_ARBIT_HZ
config HZ_1000
bool "1000 HZ" if SYS_SUPPORTS_1000HZ || SYS_SUPPORTS_ARBIT_HZ
config HZ_1024
bool "1024 HZ" if SYS_SUPPORTS_1024HZ || SYS_SUPPORTS_ARBIT_HZ
endchoice
config SYS_SUPPORTS_48HZ
bool
config SYS_SUPPORTS_100HZ
bool
config SYS_SUPPORTS_128HZ
bool
config SYS_SUPPORTS_250HZ
bool
config SYS_SUPPORTS_256HZ
bool
config SYS_SUPPORTS_1000HZ
bool
config SYS_SUPPORTS_1024HZ
bool
config SYS_SUPPORTS_ARBIT_HZ
bool
default y if !SYS_SUPPORTS_48HZ && !SYS_SUPPORTS_100HZ && \
!SYS_SUPPORTS_128HZ && !SYS_SUPPORTS_250HZ && \
!SYS_SUPPORTS_256HZ && !SYS_SUPPORTS_1000HZ && \
!SYS_SUPPORTS_1024HZ
config HZ
int
default 48 if HZ_48
default 100 if HZ_100
default 128 if HZ_128
default 250 if HZ_250
default 256 if HZ_256
default 1000 if HZ_1000
default 1024 if HZ_1024
source "kernel/Kconfig.preempt"
config MIPS_INSANE_LARGE
bool "Support for large 64-bit configurations"
depends on CPU_R10000 && 64BIT
help
MIPS R10000 does support a 44 bit / 16TB address space as opposed to
previous 64-bit processors which only supported 40 bit / 1TB. If you
need processes of more than 1TB virtual address space, say Y here.
This will result in additional memory usage, so it is not
recommended for normal users.
config KEXEC
bool "Kexec system call (EXPERIMENTAL)"
depends on EXPERIMENTAL
help
kexec is a system call that implements the ability to shutdown your
current kernel, and to start another kernel. It is like a reboot
but it is independent of the system firmware. And like a reboot
you can start any kernel with it, not just Linux.
The name comes from the similarity to the exec system call.
It is an ongoing process to be certain the hardware in a machine
is properly shutdown, so do not be surprised if this code does not
initially work for you. It may help to enable device hotplugging
support. As of this writing the exact hardware interface is
strongly in flux, so no good recommendation can be made.
config SECCOMP
bool "Enable seccomp to safely compute untrusted bytecode"
depends on PROC_FS
default y
help
This kernel feature is useful for number crunching applications
that may need to compute untrusted bytecode during their
execution. By using pipes or other transports made available to
the process as file descriptors supporting the read/write
syscalls, it's possible to isolate those applications in
their own address space using seccomp. Once seccomp is
enabled via /proc/<pid>/seccomp, it cannot be disabled
and the task is only allowed to execute a few safe syscalls
defined by each seccomp mode.
If unsure, say Y. Only embedded should say N here.
endmenu
config RWSEM_GENERIC_SPINLOCK
bool
default y
config LOCKDEP_SUPPORT
bool
default y
config STACKTRACE_SUPPORT
bool
default y
source "init/Kconfig"
menu "Bus options (PCI, PCMCIA, EISA, ISA, TC)"
config HW_HAS_EISA
bool
config HW_HAS_PCI
bool
config PCI
bool "Support for PCI controller"
depends on HW_HAS_PCI
select PCI_DOMAINS
help
Find out whether you have a PCI motherboard. PCI is the name of a
bus system, i.e. the way the CPU talks to the other stuff inside
your box. Other bus systems are ISA, EISA, or VESA. If you have PCI,
say Y, otherwise N.
config PCI_DOMAINS
bool
source "drivers/pci/Kconfig"
#
# ISA support is now enabled via select. Too many systems still have the one
# or other ISA chip on the board that users don't know about so don't expect
# users to choose the right thing ...
#
config ISA
bool
config EISA
bool "EISA support"
depends on HW_HAS_EISA
select ISA
select GENERIC_ISA_DMA
---help---
The Extended Industry Standard Architecture (EISA) bus was
developed as an open alternative to the IBM MicroChannel bus.
The EISA bus provided some of the features of the IBM MicroChannel
bus while maintaining backward compatibility with cards made for
the older ISA bus. The EISA bus saw limited use between 1988 and
1995 when it was made obsolete by the PCI bus.
Say Y here if you are building a kernel for an EISA-based machine.
Otherwise, say N.
source "drivers/eisa/Kconfig"
config TC
bool "TURBOchannel support"
depends on MACH_DECSTATION
help
TurboChannel is a DEC (now Compaq (now HP)) bus for Alpha and MIPS
processors. Documentation on writing device drivers for TurboChannel
is available at:
<http://www.cs.arizona.edu/computer.help/policy/DIGITAL_unix/AA-PS3HD-TET1_html/TITLE.html>.
#config ACCESSBUS
# bool "Access.Bus support"
# depends on TC
config MMU
bool
default y
config I8253
bool
config ZONE_DMA32
bool
source "drivers/pcmcia/Kconfig"
source "drivers/pci/hotplug/Kconfig"
endmenu
menu "Executable file formats"
source "fs/Kconfig.binfmt"
config TRAD_SIGNALS
bool
config MIPS32_COMPAT
bool "Kernel support for Linux/MIPS 32-bit binary compatibility"
depends on 64BIT
help
Select this option if you want Linux/MIPS 32-bit binary
compatibility. Since all software available for Linux/MIPS is
currently 32-bit you should say Y here.
config COMPAT
bool
depends on MIPS32_COMPAT
default y
config SYSVIPC_COMPAT
bool
depends on COMPAT && SYSVIPC
default y
config MIPS32_O32
bool "Kernel support for o32 binaries"
depends on MIPS32_COMPAT
help
Select this option if you want to run o32 binaries. These are pure
32-bit binaries as used by the 32-bit Linux/MIPS port. Most of
existing binaries are in this format.
If unsure, say Y.
config MIPS32_N32
bool "Kernel support for n32 binaries"
depends on MIPS32_COMPAT
help
Select this option if you want to run n32 binaries. These are
64-bit binaries using 32-bit quantities for addressing and certain
data that would normally be 64-bit. They are used in special
cases.
If unsure, say N.
config BINFMT_ELF32
bool
default y if MIPS32_O32 || MIPS32_N32
endmenu
menu "Power management options"
config ARCH_SUSPEND_POSSIBLE
def_bool y
depends on !SMP
source "kernel/power/Kconfig"
endmenu
source "net/Kconfig"
source "drivers/Kconfig"
source "fs/Kconfig"
source "arch/mips/Kconfig.debug"
source "security/Kconfig"
source "crypto/Kconfig"
source "lib/Kconfig"