linux/drivers/spi/spi-bcm63xx-hsspi.c
Dan Carpenter 97b7cea04f
spi: bcm63xx-hsspi: fix error code in probe
This code accidentally returns success instead of a negative error code.

Fixes: 50a6620dd1 ("spi: bcm63xx-hsspi: Add polling mode support")
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/Y+zmoGH6LubPhiI0@kili
Signed-off-by: Mark Brown <broonie@kernel.org>
2023-02-15 22:29:51 +00:00

958 lines
26 KiB
C

/*
* Broadcom BCM63XX High Speed SPI Controller driver
*
* Copyright 2000-2010 Broadcom Corporation
* Copyright 2012-2013 Jonas Gorski <jogo@openwrt.org>
*
* Licensed under the GNU/GPL. See COPYING for details.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/clk.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/err.h>
#include <linux/interrupt.h>
#include <linux/spi/spi.h>
#include <linux/mutex.h>
#include <linux/of.h>
#include <linux/spi/spi-mem.h>
#include <linux/mtd/spi-nor.h>
#include <linux/reset.h>
#include <linux/pm_runtime.h>
#define HSSPI_GLOBAL_CTRL_REG 0x0
#define GLOBAL_CTRL_CS_POLARITY_SHIFT 0
#define GLOBAL_CTRL_CS_POLARITY_MASK 0x000000ff
#define GLOBAL_CTRL_PLL_CLK_CTRL_SHIFT 8
#define GLOBAL_CTRL_PLL_CLK_CTRL_MASK 0x0000ff00
#define GLOBAL_CTRL_CLK_GATE_SSOFF BIT(16)
#define GLOBAL_CTRL_CLK_POLARITY BIT(17)
#define GLOBAL_CTRL_MOSI_IDLE BIT(18)
#define HSSPI_GLOBAL_EXT_TRIGGER_REG 0x4
#define HSSPI_INT_STATUS_REG 0x8
#define HSSPI_INT_STATUS_MASKED_REG 0xc
#define HSSPI_INT_MASK_REG 0x10
#define HSSPI_PINGx_CMD_DONE(i) BIT((i * 8) + 0)
#define HSSPI_PINGx_RX_OVER(i) BIT((i * 8) + 1)
#define HSSPI_PINGx_TX_UNDER(i) BIT((i * 8) + 2)
#define HSSPI_PINGx_POLL_TIMEOUT(i) BIT((i * 8) + 3)
#define HSSPI_PINGx_CTRL_INVAL(i) BIT((i * 8) + 4)
#define HSSPI_INT_CLEAR_ALL 0xff001f1f
#define HSSPI_PINGPONG_COMMAND_REG(x) (0x80 + (x) * 0x40)
#define PINGPONG_CMD_COMMAND_MASK 0xf
#define PINGPONG_COMMAND_NOOP 0
#define PINGPONG_COMMAND_START_NOW 1
#define PINGPONG_COMMAND_START_TRIGGER 2
#define PINGPONG_COMMAND_HALT 3
#define PINGPONG_COMMAND_FLUSH 4
#define PINGPONG_CMD_PROFILE_SHIFT 8
#define PINGPONG_CMD_SS_SHIFT 12
#define HSSPI_PINGPONG_STATUS_REG(x) (0x84 + (x) * 0x40)
#define HSSPI_PINGPONG_STATUS_SRC_BUSY BIT(1)
#define HSSPI_PROFILE_CLK_CTRL_REG(x) (0x100 + (x) * 0x20)
#define CLK_CTRL_FREQ_CTRL_MASK 0x0000ffff
#define CLK_CTRL_SPI_CLK_2X_SEL BIT(14)
#define CLK_CTRL_ACCUM_RST_ON_LOOP BIT(15)
#define HSSPI_PROFILE_SIGNAL_CTRL_REG(x) (0x104 + (x) * 0x20)
#define SIGNAL_CTRL_LATCH_RISING BIT(12)
#define SIGNAL_CTRL_LAUNCH_RISING BIT(13)
#define SIGNAL_CTRL_ASYNC_INPUT_PATH BIT(16)
#define HSSPI_PROFILE_MODE_CTRL_REG(x) (0x108 + (x) * 0x20)
#define MODE_CTRL_MULTIDATA_RD_STRT_SHIFT 8
#define MODE_CTRL_MULTIDATA_WR_STRT_SHIFT 12
#define MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT 16
#define MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT 18
#define MODE_CTRL_MODE_3WIRE BIT(20)
#define MODE_CTRL_PREPENDBYTE_CNT_SHIFT 24
#define HSSPI_FIFO_REG(x) (0x200 + (x) * 0x200)
#define HSSPI_OP_MULTIBIT BIT(11)
#define HSSPI_OP_CODE_SHIFT 13
#define HSSPI_OP_SLEEP (0 << HSSPI_OP_CODE_SHIFT)
#define HSSPI_OP_READ_WRITE (1 << HSSPI_OP_CODE_SHIFT)
#define HSSPI_OP_WRITE (2 << HSSPI_OP_CODE_SHIFT)
#define HSSPI_OP_READ (3 << HSSPI_OP_CODE_SHIFT)
#define HSSPI_OP_SETIRQ (4 << HSSPI_OP_CODE_SHIFT)
#define HSSPI_BUFFER_LEN 512
#define HSSPI_OPCODE_LEN 2
#define HSSPI_MAX_PREPEND_LEN 15
/*
* Some chip require 30MHz but other require 25MHz. Use smaller value to cover
* both cases.
*/
#define HSSPI_MAX_SYNC_CLOCK 25000000
#define HSSPI_SPI_MAX_CS 8
#define HSSPI_BUS_NUM 1 /* 0 is legacy SPI */
#define HSSPI_POLL_STATUS_TIMEOUT_MS 100
#define HSSPI_WAIT_MODE_POLLING 0
#define HSSPI_WAIT_MODE_INTR 1
#define HSSPI_WAIT_MODE_MAX HSSPI_WAIT_MODE_INTR
/*
* Default transfer mode is auto. If the msg is prependable, use the prepend
* mode. If not, falls back to use the dummy cs workaround mode but limit the
* clock to 25MHz to make sure it works in all board design.
*/
#define HSSPI_XFER_MODE_AUTO 0
#define HSSPI_XFER_MODE_PREPEND 1
#define HSSPI_XFER_MODE_DUMMYCS 2
#define HSSPI_XFER_MODE_MAX HSSPI_XFER_MODE_DUMMYCS
#define bcm63xx_prepend_printk_on_checkfail(bs, fmt, ...) \
do { \
if (bs->xfer_mode == HSSPI_XFER_MODE_AUTO) \
dev_dbg(&bs->pdev->dev, fmt, ##__VA_ARGS__); \
else if (bs->xfer_mode == HSSPI_XFER_MODE_PREPEND) \
dev_err(&bs->pdev->dev, fmt, ##__VA_ARGS__); \
} while (0)
struct bcm63xx_hsspi {
struct completion done;
struct mutex bus_mutex;
struct mutex msg_mutex;
struct platform_device *pdev;
struct clk *clk;
struct clk *pll_clk;
void __iomem *regs;
u8 __iomem *fifo;
u32 speed_hz;
u8 cs_polarity;
u32 wait_mode;
u32 xfer_mode;
u32 prepend_cnt;
u8 *prepend_buf;
};
static ssize_t wait_mode_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct spi_controller *ctrl = dev_get_drvdata(dev);
struct bcm63xx_hsspi *bs = spi_master_get_devdata(ctrl);
return sprintf(buf, "%d\n", bs->wait_mode);
}
static ssize_t wait_mode_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct spi_controller *ctrl = dev_get_drvdata(dev);
struct bcm63xx_hsspi *bs = spi_master_get_devdata(ctrl);
u32 val;
if (kstrtou32(buf, 10, &val))
return -EINVAL;
if (val > HSSPI_WAIT_MODE_MAX) {
dev_warn(dev, "invalid wait mode %u\n", val);
return -EINVAL;
}
mutex_lock(&bs->msg_mutex);
bs->wait_mode = val;
/* clear interrupt status to avoid spurious int on next transfer */
if (val == HSSPI_WAIT_MODE_INTR)
__raw_writel(HSSPI_INT_CLEAR_ALL, bs->regs + HSSPI_INT_STATUS_REG);
mutex_unlock(&bs->msg_mutex);
return count;
}
static DEVICE_ATTR_RW(wait_mode);
static ssize_t xfer_mode_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct spi_controller *ctrl = dev_get_drvdata(dev);
struct bcm63xx_hsspi *bs = spi_master_get_devdata(ctrl);
return sprintf(buf, "%d\n", bs->xfer_mode);
}
static ssize_t xfer_mode_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct spi_controller *ctrl = dev_get_drvdata(dev);
struct bcm63xx_hsspi *bs = spi_master_get_devdata(ctrl);
u32 val;
if (kstrtou32(buf, 10, &val))
return -EINVAL;
if (val > HSSPI_XFER_MODE_MAX) {
dev_warn(dev, "invalid xfer mode %u\n", val);
return -EINVAL;
}
mutex_lock(&bs->msg_mutex);
bs->xfer_mode = val;
mutex_unlock(&bs->msg_mutex);
return count;
}
static DEVICE_ATTR_RW(xfer_mode);
static struct attribute *bcm63xx_hsspi_attrs[] = {
&dev_attr_wait_mode.attr,
&dev_attr_xfer_mode.attr,
NULL,
};
static const struct attribute_group bcm63xx_hsspi_group = {
.attrs = bcm63xx_hsspi_attrs,
};
static void bcm63xx_hsspi_set_clk(struct bcm63xx_hsspi *bs,
struct spi_device *spi, int hz);
static size_t bcm63xx_hsspi_max_message_size(struct spi_device *spi)
{
return HSSPI_BUFFER_LEN - HSSPI_OPCODE_LEN;
}
static int bcm63xx_hsspi_wait_cmd(struct bcm63xx_hsspi *bs)
{
unsigned long limit;
u32 reg = 0;
int rc = 0;
if (bs->wait_mode == HSSPI_WAIT_MODE_INTR) {
if (wait_for_completion_timeout(&bs->done, HZ) == 0)
rc = 1;
} else {
/* polling mode checks for status busy bit */
limit = jiffies + msecs_to_jiffies(HSSPI_POLL_STATUS_TIMEOUT_MS);
while (!time_after(jiffies, limit)) {
reg = __raw_readl(bs->regs + HSSPI_PINGPONG_STATUS_REG(0));
if (reg & HSSPI_PINGPONG_STATUS_SRC_BUSY)
cpu_relax();
else
break;
}
if (reg & HSSPI_PINGPONG_STATUS_SRC_BUSY)
rc = 1;
}
if (rc)
dev_err(&bs->pdev->dev, "transfer timed out!\n");
return rc;
}
static bool bcm63xx_prepare_prepend_transfer(struct spi_master *master,
struct spi_message *msg,
struct spi_transfer *t_prepend)
{
struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
bool tx_only = false;
struct spi_transfer *t;
/*
* Multiple transfers within a message may be combined into one transfer
* to the controller using its prepend feature. A SPI message is prependable
* only if the following are all true:
* 1. One or more half duplex write transfer in single bit mode
* 2. Optional full duplex read/write at the end
* 3. No delay and cs_change between transfers
*/
bs->prepend_cnt = 0;
list_for_each_entry(t, &msg->transfers, transfer_list) {
if ((spi_delay_to_ns(&t->delay, t) > 0) || t->cs_change) {
bcm63xx_prepend_printk_on_checkfail(bs,
"Delay or cs change not supported in prepend mode!\n");
return false;
}
tx_only = false;
if (t->tx_buf && !t->rx_buf) {
tx_only = true;
if (bs->prepend_cnt + t->len >
(HSSPI_BUFFER_LEN - HSSPI_OPCODE_LEN)) {
bcm63xx_prepend_printk_on_checkfail(bs,
"exceed max buf len, abort prepending transfers!\n");
return false;
}
if (t->tx_nbits > SPI_NBITS_SINGLE &&
!list_is_last(&t->transfer_list, &msg->transfers)) {
bcm63xx_prepend_printk_on_checkfail(bs,
"multi-bit prepend buf not supported!\n");
return false;
}
if (t->tx_nbits == SPI_NBITS_SINGLE) {
memcpy(bs->prepend_buf + bs->prepend_cnt, t->tx_buf, t->len);
bs->prepend_cnt += t->len;
}
} else {
if (!list_is_last(&t->transfer_list, &msg->transfers)) {
bcm63xx_prepend_printk_on_checkfail(bs,
"rx/tx_rx transfer not supported when it is not last one!\n");
return false;
}
}
if (list_is_last(&t->transfer_list, &msg->transfers)) {
memcpy(t_prepend, t, sizeof(struct spi_transfer));
if (tx_only && t->tx_nbits == SPI_NBITS_SINGLE) {
/*
* if the last one is also a single bit tx only transfer, merge
* all of them into one single tx transfer
*/
t_prepend->len = bs->prepend_cnt;
t_prepend->tx_buf = bs->prepend_buf;
bs->prepend_cnt = 0;
} else {
/*
* if the last one is not a tx only transfer or dual tx xfer, all
* the previous transfers are sent through prepend bytes and
* make sure it does not exceed the max prepend len
*/
if (bs->prepend_cnt > HSSPI_MAX_PREPEND_LEN) {
bcm63xx_prepend_printk_on_checkfail(bs,
"exceed max prepend len, abort prepending transfers!\n");
return false;
}
}
}
}
return true;
}
static int bcm63xx_hsspi_do_prepend_txrx(struct spi_device *spi,
struct spi_transfer *t)
{
struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master);
unsigned int chip_select = spi->chip_select;
u16 opcode = 0, val;
const u8 *tx = t->tx_buf;
u8 *rx = t->rx_buf;
u32 reg = 0;
/*
* shouldn't happen as we set the max_message_size in the probe.
* but check it again in case some driver does not honor the max size
*/
if (t->len + bs->prepend_cnt > (HSSPI_BUFFER_LEN - HSSPI_OPCODE_LEN)) {
dev_warn(&bs->pdev->dev,
"Prepend message large than fifo size len %d prepend %d\n",
t->len, bs->prepend_cnt);
return -EINVAL;
}
bcm63xx_hsspi_set_clk(bs, spi, t->speed_hz);
if (tx && rx)
opcode = HSSPI_OP_READ_WRITE;
else if (tx)
opcode = HSSPI_OP_WRITE;
else if (rx)
opcode = HSSPI_OP_READ;
if ((opcode == HSSPI_OP_READ && t->rx_nbits == SPI_NBITS_DUAL) ||
(opcode == HSSPI_OP_WRITE && t->tx_nbits == SPI_NBITS_DUAL)) {
opcode |= HSSPI_OP_MULTIBIT;
if (t->rx_nbits == SPI_NBITS_DUAL) {
reg |= 1 << MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT;
reg |= bs->prepend_cnt << MODE_CTRL_MULTIDATA_RD_STRT_SHIFT;
}
if (t->tx_nbits == SPI_NBITS_DUAL) {
reg |= 1 << MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT;
reg |= bs->prepend_cnt << MODE_CTRL_MULTIDATA_WR_STRT_SHIFT;
}
}
reg |= bs->prepend_cnt << MODE_CTRL_PREPENDBYTE_CNT_SHIFT;
__raw_writel(reg | 0xff,
bs->regs + HSSPI_PROFILE_MODE_CTRL_REG(chip_select));
reinit_completion(&bs->done);
if (bs->prepend_cnt)
memcpy_toio(bs->fifo + HSSPI_OPCODE_LEN, bs->prepend_buf,
bs->prepend_cnt);
if (tx)
memcpy_toio(bs->fifo + HSSPI_OPCODE_LEN + bs->prepend_cnt, tx,
t->len);
*(__be16 *)(&val) = cpu_to_be16(opcode | t->len);
__raw_writew(val, bs->fifo);
/* enable interrupt */
if (bs->wait_mode == HSSPI_WAIT_MODE_INTR)
__raw_writel(HSSPI_PINGx_CMD_DONE(0), bs->regs + HSSPI_INT_MASK_REG);
/* start the transfer */
reg = chip_select << PINGPONG_CMD_SS_SHIFT |
chip_select << PINGPONG_CMD_PROFILE_SHIFT |
PINGPONG_COMMAND_START_NOW;
__raw_writel(reg, bs->regs + HSSPI_PINGPONG_COMMAND_REG(0));
if (bcm63xx_hsspi_wait_cmd(bs))
return -ETIMEDOUT;
if (rx)
memcpy_fromio(rx, bs->fifo, t->len);
return 0;
}
static void bcm63xx_hsspi_set_cs(struct bcm63xx_hsspi *bs, unsigned int cs,
bool active)
{
u32 reg;
mutex_lock(&bs->bus_mutex);
reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
reg &= ~BIT(cs);
if (active == !(bs->cs_polarity & BIT(cs)))
reg |= BIT(cs);
__raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG);
mutex_unlock(&bs->bus_mutex);
}
static void bcm63xx_hsspi_set_clk(struct bcm63xx_hsspi *bs,
struct spi_device *spi, int hz)
{
unsigned int profile = spi->chip_select;
u32 reg;
reg = DIV_ROUND_UP(2048, DIV_ROUND_UP(bs->speed_hz, hz));
__raw_writel(CLK_CTRL_ACCUM_RST_ON_LOOP | reg,
bs->regs + HSSPI_PROFILE_CLK_CTRL_REG(profile));
reg = __raw_readl(bs->regs + HSSPI_PROFILE_SIGNAL_CTRL_REG(profile));
if (hz > HSSPI_MAX_SYNC_CLOCK)
reg |= SIGNAL_CTRL_ASYNC_INPUT_PATH;
else
reg &= ~SIGNAL_CTRL_ASYNC_INPUT_PATH;
__raw_writel(reg, bs->regs + HSSPI_PROFILE_SIGNAL_CTRL_REG(profile));
mutex_lock(&bs->bus_mutex);
/* setup clock polarity */
reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
reg &= ~GLOBAL_CTRL_CLK_POLARITY;
if (spi->mode & SPI_CPOL)
reg |= GLOBAL_CTRL_CLK_POLARITY;
__raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG);
mutex_unlock(&bs->bus_mutex);
}
static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t)
{
struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master);
unsigned int chip_select = spi->chip_select;
u16 opcode = 0, val;
int pending = t->len;
int step_size = HSSPI_BUFFER_LEN;
const u8 *tx = t->tx_buf;
u8 *rx = t->rx_buf;
u32 reg = 0;
bcm63xx_hsspi_set_clk(bs, spi, t->speed_hz);
if (!t->cs_off)
bcm63xx_hsspi_set_cs(bs, spi->chip_select, true);
if (tx && rx)
opcode = HSSPI_OP_READ_WRITE;
else if (tx)
opcode = HSSPI_OP_WRITE;
else if (rx)
opcode = HSSPI_OP_READ;
if (opcode != HSSPI_OP_READ)
step_size -= HSSPI_OPCODE_LEN;
if ((opcode == HSSPI_OP_READ && t->rx_nbits == SPI_NBITS_DUAL) ||
(opcode == HSSPI_OP_WRITE && t->tx_nbits == SPI_NBITS_DUAL)) {
opcode |= HSSPI_OP_MULTIBIT;
if (t->rx_nbits == SPI_NBITS_DUAL)
reg |= 1 << MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT;
if (t->tx_nbits == SPI_NBITS_DUAL)
reg |= 1 << MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT;
}
__raw_writel(reg | 0xff,
bs->regs + HSSPI_PROFILE_MODE_CTRL_REG(chip_select));
while (pending > 0) {
int curr_step = min_t(int, step_size, pending);
reinit_completion(&bs->done);
if (tx) {
memcpy_toio(bs->fifo + HSSPI_OPCODE_LEN, tx, curr_step);
tx += curr_step;
}
*(__be16 *)(&val) = cpu_to_be16(opcode | curr_step);
__raw_writew(val, bs->fifo);
/* enable interrupt */
if (bs->wait_mode == HSSPI_WAIT_MODE_INTR)
__raw_writel(HSSPI_PINGx_CMD_DONE(0),
bs->regs + HSSPI_INT_MASK_REG);
reg = !chip_select << PINGPONG_CMD_SS_SHIFT |
chip_select << PINGPONG_CMD_PROFILE_SHIFT |
PINGPONG_COMMAND_START_NOW;
__raw_writel(reg, bs->regs + HSSPI_PINGPONG_COMMAND_REG(0));
if (bcm63xx_hsspi_wait_cmd(bs))
return -ETIMEDOUT;
if (rx) {
memcpy_fromio(rx, bs->fifo, curr_step);
rx += curr_step;
}
pending -= curr_step;
}
return 0;
}
static int bcm63xx_hsspi_setup(struct spi_device *spi)
{
struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master);
u32 reg;
reg = __raw_readl(bs->regs +
HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select));
reg &= ~(SIGNAL_CTRL_LAUNCH_RISING | SIGNAL_CTRL_LATCH_RISING);
if (spi->mode & SPI_CPHA)
reg |= SIGNAL_CTRL_LAUNCH_RISING;
else
reg |= SIGNAL_CTRL_LATCH_RISING;
__raw_writel(reg, bs->regs +
HSSPI_PROFILE_SIGNAL_CTRL_REG(spi->chip_select));
mutex_lock(&bs->bus_mutex);
reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
/* only change actual polarities if there is no transfer */
if ((reg & GLOBAL_CTRL_CS_POLARITY_MASK) == bs->cs_polarity) {
if (spi->mode & SPI_CS_HIGH)
reg |= BIT(spi->chip_select);
else
reg &= ~BIT(spi->chip_select);
__raw_writel(reg, bs->regs + HSSPI_GLOBAL_CTRL_REG);
}
if (spi->mode & SPI_CS_HIGH)
bs->cs_polarity |= BIT(spi->chip_select);
else
bs->cs_polarity &= ~BIT(spi->chip_select);
mutex_unlock(&bs->bus_mutex);
return 0;
}
static int bcm63xx_hsspi_do_dummy_cs_txrx(struct spi_device *spi,
struct spi_message *msg)
{
struct bcm63xx_hsspi *bs = spi_master_get_devdata(spi->master);
int status = -EINVAL;
int dummy_cs;
bool keep_cs = false;
struct spi_transfer *t;
/*
* This controller does not support keeping CS active during idle.
* To work around this, we use the following ugly hack:
*
* a. Invert the target chip select's polarity so it will be active.
* b. Select a "dummy" chip select to use as the hardware target.
* c. Invert the dummy chip select's polarity so it will be inactive
* during the actual transfers.
* d. Tell the hardware to send to the dummy chip select. Thanks to
* the multiplexed nature of SPI the actual target will receive
* the transfer and we see its response.
*
* e. At the end restore the polarities again to their default values.
*/
dummy_cs = !spi->chip_select;
bcm63xx_hsspi_set_cs(bs, dummy_cs, true);
list_for_each_entry(t, &msg->transfers, transfer_list) {
/*
* We are here because one of reasons below:
* a. Message is not prependable and in default auto xfer mode. This mean
* we fallback to dummy cs mode at maximum 25MHz safe clock rate.
* b. User set to use the dummy cs mode.
*/
if (bs->xfer_mode == HSSPI_XFER_MODE_AUTO) {
if (t->speed_hz > HSSPI_MAX_SYNC_CLOCK) {
t->speed_hz = HSSPI_MAX_SYNC_CLOCK;
dev_warn_once(&bs->pdev->dev,
"Force to dummy cs mode. Reduce the speed to %dHz",
t->speed_hz);
}
}
status = bcm63xx_hsspi_do_txrx(spi, t);
if (status)
break;
msg->actual_length += t->len;
spi_transfer_delay_exec(t);
/* use existing cs change logic from spi_transfer_one_message */
if (t->cs_change) {
if (list_is_last(&t->transfer_list, &msg->transfers)) {
keep_cs = true;
} else {
if (!t->cs_off)
bcm63xx_hsspi_set_cs(bs, spi->chip_select, false);
spi_transfer_cs_change_delay_exec(msg, t);
if (!list_next_entry(t, transfer_list)->cs_off)
bcm63xx_hsspi_set_cs(bs, spi->chip_select, true);
}
} else if (!list_is_last(&t->transfer_list, &msg->transfers) &&
t->cs_off != list_next_entry(t, transfer_list)->cs_off) {
bcm63xx_hsspi_set_cs(bs, spi->chip_select, t->cs_off);
}
}
bcm63xx_hsspi_set_cs(bs, dummy_cs, false);
if (status || !keep_cs)
bcm63xx_hsspi_set_cs(bs, spi->chip_select, false);
return status;
}
static int bcm63xx_hsspi_transfer_one(struct spi_master *master,
struct spi_message *msg)
{
struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
struct spi_device *spi = msg->spi;
int status = -EINVAL;
bool prependable = false;
struct spi_transfer t_prepend;
mutex_lock(&bs->msg_mutex);
if (bs->xfer_mode != HSSPI_XFER_MODE_DUMMYCS)
prependable = bcm63xx_prepare_prepend_transfer(master, msg, &t_prepend);
if (prependable) {
status = bcm63xx_hsspi_do_prepend_txrx(spi, &t_prepend);
msg->actual_length = (t_prepend.len + bs->prepend_cnt);
} else {
if (bs->xfer_mode == HSSPI_XFER_MODE_PREPEND) {
dev_err(&bs->pdev->dev,
"User sets prepend mode but msg not prependable! Abort transfer\n");
status = -EINVAL;
} else
status = bcm63xx_hsspi_do_dummy_cs_txrx(spi, msg);
}
mutex_unlock(&bs->msg_mutex);
msg->status = status;
spi_finalize_current_message(master);
return 0;
}
static bool bcm63xx_hsspi_mem_supports_op(struct spi_mem *mem,
const struct spi_mem_op *op)
{
if (!spi_mem_default_supports_op(mem, op))
return false;
/* Controller doesn't support spi mem dual io mode */
if ((op->cmd.opcode == SPINOR_OP_READ_1_2_2) ||
(op->cmd.opcode == SPINOR_OP_READ_1_2_2_4B) ||
(op->cmd.opcode == SPINOR_OP_READ_1_2_2_DTR) ||
(op->cmd.opcode == SPINOR_OP_READ_1_2_2_DTR_4B))
return false;
return true;
}
static const struct spi_controller_mem_ops bcm63xx_hsspi_mem_ops = {
.supports_op = bcm63xx_hsspi_mem_supports_op,
};
static irqreturn_t bcm63xx_hsspi_interrupt(int irq, void *dev_id)
{
struct bcm63xx_hsspi *bs = (struct bcm63xx_hsspi *)dev_id;
if (__raw_readl(bs->regs + HSSPI_INT_STATUS_MASKED_REG) == 0)
return IRQ_NONE;
__raw_writel(HSSPI_INT_CLEAR_ALL, bs->regs + HSSPI_INT_STATUS_REG);
__raw_writel(0, bs->regs + HSSPI_INT_MASK_REG);
complete(&bs->done);
return IRQ_HANDLED;
}
static int bcm63xx_hsspi_probe(struct platform_device *pdev)
{
struct spi_master *master;
struct bcm63xx_hsspi *bs;
void __iomem *regs;
struct device *dev = &pdev->dev;
struct clk *clk, *pll_clk = NULL;
int irq, ret;
u32 reg, rate, num_cs = HSSPI_SPI_MAX_CS;
struct reset_control *reset;
irq = platform_get_irq(pdev, 0);
if (irq < 0)
return irq;
regs = devm_platform_ioremap_resource(pdev, 0);
if (IS_ERR(regs))
return PTR_ERR(regs);
clk = devm_clk_get(dev, "hsspi");
if (IS_ERR(clk))
return PTR_ERR(clk);
reset = devm_reset_control_get_optional_exclusive(dev, NULL);
if (IS_ERR(reset))
return PTR_ERR(reset);
ret = clk_prepare_enable(clk);
if (ret)
return ret;
ret = reset_control_reset(reset);
if (ret) {
dev_err(dev, "unable to reset device: %d\n", ret);
goto out_disable_clk;
}
rate = clk_get_rate(clk);
if (!rate) {
pll_clk = devm_clk_get(dev, "pll");
if (IS_ERR(pll_clk)) {
ret = PTR_ERR(pll_clk);
goto out_disable_clk;
}
ret = clk_prepare_enable(pll_clk);
if (ret)
goto out_disable_clk;
rate = clk_get_rate(pll_clk);
if (!rate) {
ret = -EINVAL;
goto out_disable_pll_clk;
}
}
master = spi_alloc_master(&pdev->dev, sizeof(*bs));
if (!master) {
ret = -ENOMEM;
goto out_disable_pll_clk;
}
bs = spi_master_get_devdata(master);
bs->pdev = pdev;
bs->clk = clk;
bs->pll_clk = pll_clk;
bs->regs = regs;
bs->speed_hz = rate;
bs->fifo = (u8 __iomem *)(bs->regs + HSSPI_FIFO_REG(0));
bs->wait_mode = HSSPI_WAIT_MODE_POLLING;
bs->prepend_buf = devm_kzalloc(dev, HSSPI_BUFFER_LEN, GFP_KERNEL);
if (!bs->prepend_buf) {
ret = -ENOMEM;
goto out_put_master;
}
mutex_init(&bs->bus_mutex);
mutex_init(&bs->msg_mutex);
init_completion(&bs->done);
master->mem_ops = &bcm63xx_hsspi_mem_ops;
master->dev.of_node = dev->of_node;
if (!dev->of_node)
master->bus_num = HSSPI_BUS_NUM;
of_property_read_u32(dev->of_node, "num-cs", &num_cs);
if (num_cs > 8) {
dev_warn(dev, "unsupported number of cs (%i), reducing to 8\n",
num_cs);
num_cs = HSSPI_SPI_MAX_CS;
}
master->num_chipselect = num_cs;
master->setup = bcm63xx_hsspi_setup;
master->transfer_one_message = bcm63xx_hsspi_transfer_one;
master->max_transfer_size = bcm63xx_hsspi_max_message_size;
master->max_message_size = bcm63xx_hsspi_max_message_size;
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH |
SPI_RX_DUAL | SPI_TX_DUAL;
master->bits_per_word_mask = SPI_BPW_MASK(8);
master->auto_runtime_pm = true;
platform_set_drvdata(pdev, master);
/* Initialize the hardware */
__raw_writel(0, bs->regs + HSSPI_INT_MASK_REG);
/* clean up any pending interrupts */
__raw_writel(HSSPI_INT_CLEAR_ALL, bs->regs + HSSPI_INT_STATUS_REG);
/* read out default CS polarities */
reg = __raw_readl(bs->regs + HSSPI_GLOBAL_CTRL_REG);
bs->cs_polarity = reg & GLOBAL_CTRL_CS_POLARITY_MASK;
__raw_writel(reg | GLOBAL_CTRL_CLK_GATE_SSOFF,
bs->regs + HSSPI_GLOBAL_CTRL_REG);
if (irq > 0) {
ret = devm_request_irq(dev, irq, bcm63xx_hsspi_interrupt, IRQF_SHARED,
pdev->name, bs);
if (ret)
goto out_put_master;
}
pm_runtime_enable(&pdev->dev);
ret = sysfs_create_group(&pdev->dev.kobj, &bcm63xx_hsspi_group);
if (ret) {
dev_err(&pdev->dev, "couldn't register sysfs group\n");
goto out_pm_disable;
}
/* register and we are done */
ret = devm_spi_register_master(dev, master);
if (ret)
goto out_sysgroup_disable;
dev_info(dev, "Broadcom 63XX High Speed SPI Controller driver");
return 0;
out_sysgroup_disable:
sysfs_remove_group(&pdev->dev.kobj, &bcm63xx_hsspi_group);
out_pm_disable:
pm_runtime_disable(&pdev->dev);
out_put_master:
spi_master_put(master);
out_disable_pll_clk:
clk_disable_unprepare(pll_clk);
out_disable_clk:
clk_disable_unprepare(clk);
return ret;
}
static int bcm63xx_hsspi_remove(struct platform_device *pdev)
{
struct spi_master *master = platform_get_drvdata(pdev);
struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
/* reset the hardware and block queue progress */
__raw_writel(0, bs->regs + HSSPI_INT_MASK_REG);
clk_disable_unprepare(bs->pll_clk);
clk_disable_unprepare(bs->clk);
sysfs_remove_group(&pdev->dev.kobj, &bcm63xx_hsspi_group);
return 0;
}
#ifdef CONFIG_PM_SLEEP
static int bcm63xx_hsspi_suspend(struct device *dev)
{
struct spi_master *master = dev_get_drvdata(dev);
struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
spi_master_suspend(master);
clk_disable_unprepare(bs->pll_clk);
clk_disable_unprepare(bs->clk);
return 0;
}
static int bcm63xx_hsspi_resume(struct device *dev)
{
struct spi_master *master = dev_get_drvdata(dev);
struct bcm63xx_hsspi *bs = spi_master_get_devdata(master);
int ret;
ret = clk_prepare_enable(bs->clk);
if (ret)
return ret;
if (bs->pll_clk) {
ret = clk_prepare_enable(bs->pll_clk);
if (ret) {
clk_disable_unprepare(bs->clk);
return ret;
}
}
spi_master_resume(master);
return 0;
}
#endif
static SIMPLE_DEV_PM_OPS(bcm63xx_hsspi_pm_ops, bcm63xx_hsspi_suspend,
bcm63xx_hsspi_resume);
static const struct of_device_id bcm63xx_hsspi_of_match[] = {
{ .compatible = "brcm,bcm6328-hsspi", },
{ .compatible = "brcm,bcmbca-hsspi-v1.0", },
{ },
};
MODULE_DEVICE_TABLE(of, bcm63xx_hsspi_of_match);
static struct platform_driver bcm63xx_hsspi_driver = {
.driver = {
.name = "bcm63xx-hsspi",
.pm = &bcm63xx_hsspi_pm_ops,
.of_match_table = bcm63xx_hsspi_of_match,
},
.probe = bcm63xx_hsspi_probe,
.remove = bcm63xx_hsspi_remove,
};
module_platform_driver(bcm63xx_hsspi_driver);
MODULE_ALIAS("platform:bcm63xx_hsspi");
MODULE_DESCRIPTION("Broadcom BCM63xx High Speed SPI Controller driver");
MODULE_AUTHOR("Jonas Gorski <jogo@openwrt.org>");
MODULE_LICENSE("GPL");