linux/arch/arm/mach-ux500/devices-db8500.c
Linus Walleij 5d7b8467e1 mach-ux500: config Ux500 PL011 PL022 PL180 for DMA
This will configure the platform data for the PL011, PL022
and PL180 (derivate) PrimeCells found in the Ux500 to use DMA
with the generic DMA engine for DMA40.

Signed-off-by: Per Forlin <per.forlin@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2011-03-14 14:05:14 +01:00

198 lines
5.7 KiB
C

/*
* Copyright (C) ST-Ericsson SA 2010
*
* Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
* License terms: GNU General Public License (GPL) version 2
*/
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/interrupt.h>
#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/amba/bus.h>
#include <linux/amba/pl022.h>
#include <plat/ste_dma40.h>
#include <mach/hardware.h>
#include <mach/setup.h>
#include "ste-dma40-db8500.h"
static struct resource dma40_resources[] = {
[0] = {
.start = U8500_DMA_BASE,
.end = U8500_DMA_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
.name = "base",
},
[1] = {
.start = U8500_DMA_LCPA_BASE,
.end = U8500_DMA_LCPA_BASE + 2 * SZ_1K - 1,
.flags = IORESOURCE_MEM,
.name = "lcpa",
},
[2] = {
.start = IRQ_DB8500_DMA,
.end = IRQ_DB8500_DMA,
.flags = IORESOURCE_IRQ,
}
};
/* Default configuration for physcial memcpy */
struct stedma40_chan_cfg dma40_memcpy_conf_phy = {
.mode = STEDMA40_MODE_PHYSICAL,
.dir = STEDMA40_MEM_TO_MEM,
.src_info.data_width = STEDMA40_BYTE_WIDTH,
.src_info.psize = STEDMA40_PSIZE_PHY_1,
.src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
.dst_info.data_width = STEDMA40_BYTE_WIDTH,
.dst_info.psize = STEDMA40_PSIZE_PHY_1,
.dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
};
/* Default configuration for logical memcpy */
struct stedma40_chan_cfg dma40_memcpy_conf_log = {
.dir = STEDMA40_MEM_TO_MEM,
.src_info.data_width = STEDMA40_BYTE_WIDTH,
.src_info.psize = STEDMA40_PSIZE_LOG_1,
.src_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
.dst_info.data_width = STEDMA40_BYTE_WIDTH,
.dst_info.psize = STEDMA40_PSIZE_LOG_1,
.dst_info.flow_ctrl = STEDMA40_NO_FLOW_CTRL,
};
/*
* Mapping between destination event lines and physical device address.
* The event line is tied to a device and therefore the address is constant.
* When the address comes from a primecell it will be configured in runtime
* and we set the address to -1 as a placeholder.
*/
static const dma_addr_t dma40_tx_map[DB8500_DMA_NR_DEV] = {
/* MUSB - these will be runtime-reconfigured */
[DB8500_DMA_DEV39_USB_OTG_OEP_8] = -1,
[DB8500_DMA_DEV16_USB_OTG_OEP_7_15] = -1,
[DB8500_DMA_DEV17_USB_OTG_OEP_6_14] = -1,
[DB8500_DMA_DEV18_USB_OTG_OEP_5_13] = -1,
[DB8500_DMA_DEV19_USB_OTG_OEP_4_12] = -1,
[DB8500_DMA_DEV36_USB_OTG_OEP_3_11] = -1,
[DB8500_DMA_DEV37_USB_OTG_OEP_2_10] = -1,
[DB8500_DMA_DEV38_USB_OTG_OEP_1_9] = -1,
/* PrimeCells - run-time configured */
[DB8500_DMA_DEV0_SPI0_TX] = -1,
[DB8500_DMA_DEV1_SD_MMC0_TX] = -1,
[DB8500_DMA_DEV2_SD_MMC1_TX] = -1,
[DB8500_DMA_DEV3_SD_MMC2_TX] = -1,
[DB8500_DMA_DEV8_SSP0_TX] = -1,
[DB8500_DMA_DEV9_SSP1_TX] = -1,
[DB8500_DMA_DEV11_UART2_TX] = -1,
[DB8500_DMA_DEV12_UART1_TX] = -1,
[DB8500_DMA_DEV13_UART0_TX] = -1,
[DB8500_DMA_DEV28_SD_MM2_TX] = -1,
[DB8500_DMA_DEV29_SD_MM0_TX] = -1,
[DB8500_DMA_DEV32_SD_MM1_TX] = -1,
[DB8500_DMA_DEV33_SPI2_TX] = -1,
[DB8500_DMA_DEV35_SPI1_TX] = -1,
[DB8500_DMA_DEV40_SPI3_TX] = -1,
[DB8500_DMA_DEV41_SD_MM3_TX] = -1,
[DB8500_DMA_DEV42_SD_MM4_TX] = -1,
[DB8500_DMA_DEV43_SD_MM5_TX] = -1,
};
/* Mapping between source event lines and physical device address */
static const dma_addr_t dma40_rx_map[DB8500_DMA_NR_DEV] = {
/* MUSB - these will be runtime-reconfigured */
[DB8500_DMA_DEV39_USB_OTG_IEP_8] = -1,
[DB8500_DMA_DEV16_USB_OTG_IEP_7_15] = -1,
[DB8500_DMA_DEV17_USB_OTG_IEP_6_14] = -1,
[DB8500_DMA_DEV18_USB_OTG_IEP_5_13] = -1,
[DB8500_DMA_DEV19_USB_OTG_IEP_4_12] = -1,
[DB8500_DMA_DEV36_USB_OTG_IEP_3_11] = -1,
[DB8500_DMA_DEV37_USB_OTG_IEP_2_10] = -1,
[DB8500_DMA_DEV38_USB_OTG_IEP_1_9] = -1,
/* PrimeCells */
[DB8500_DMA_DEV0_SPI0_RX] = -1,
[DB8500_DMA_DEV1_SD_MMC0_RX] = -1,
[DB8500_DMA_DEV2_SD_MMC1_RX] = -1,
[DB8500_DMA_DEV3_SD_MMC2_RX] = -1,
[DB8500_DMA_DEV8_SSP0_RX] = -1,
[DB8500_DMA_DEV9_SSP1_RX] = -1,
[DB8500_DMA_DEV11_UART2_RX] = -1,
[DB8500_DMA_DEV12_UART1_RX] = -1,
[DB8500_DMA_DEV13_UART0_RX] = -1,
[DB8500_DMA_DEV28_SD_MM2_RX] = -1,
[DB8500_DMA_DEV29_SD_MM0_RX] = -1,
[DB8500_DMA_DEV32_SD_MM1_RX] = -1,
[DB8500_DMA_DEV33_SPI2_RX] = -1,
[DB8500_DMA_DEV35_SPI1_RX] = -1,
[DB8500_DMA_DEV40_SPI3_RX] = -1,
[DB8500_DMA_DEV41_SD_MM3_RX] = -1,
[DB8500_DMA_DEV42_SD_MM4_RX] = -1,
[DB8500_DMA_DEV43_SD_MM5_RX] = -1,
};
/* Reserved event lines for memcpy only */
static int dma40_memcpy_event[] = {
DB8500_DMA_MEMCPY_TX_0,
DB8500_DMA_MEMCPY_TX_1,
DB8500_DMA_MEMCPY_TX_2,
DB8500_DMA_MEMCPY_TX_3,
DB8500_DMA_MEMCPY_TX_4,
DB8500_DMA_MEMCPY_TX_5,
};
static struct stedma40_platform_data dma40_plat_data = {
.dev_len = DB8500_DMA_NR_DEV,
.dev_rx = dma40_rx_map,
.dev_tx = dma40_tx_map,
.memcpy = dma40_memcpy_event,
.memcpy_len = ARRAY_SIZE(dma40_memcpy_event),
.memcpy_conf_phy = &dma40_memcpy_conf_phy,
.memcpy_conf_log = &dma40_memcpy_conf_log,
.disabled_channels = {-1},
};
struct platform_device u8500_dma40_device = {
.dev = {
.platform_data = &dma40_plat_data,
},
.name = "dma40",
.id = 0,
.num_resources = ARRAY_SIZE(dma40_resources),
.resource = dma40_resources
};
void dma40_u8500ed_fixup(void)
{
dma40_plat_data.memcpy = NULL;
dma40_plat_data.memcpy_len = 0;
dma40_resources[0].start = U8500_DMA_BASE_ED;
dma40_resources[0].end = U8500_DMA_BASE_ED + SZ_4K - 1;
dma40_resources[1].start = U8500_DMA_LCPA_BASE_ED;
dma40_resources[1].end = U8500_DMA_LCPA_BASE_ED + 2 * SZ_1K - 1;
}
struct resource keypad_resources[] = {
[0] = {
.start = U8500_SKE_BASE,
.end = U8500_SKE_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = IRQ_DB8500_KB,
.end = IRQ_DB8500_KB,
.flags = IORESOURCE_IRQ,
},
};
struct platform_device u8500_ske_keypad_device = {
.name = "nmk-ske-keypad",
.id = -1,
.num_resources = ARRAY_SIZE(keypad_resources),
.resource = keypad_resources,
};