linux/arch/arm/mach-realview/core.c
Arnd Bergmann b70661c708 net: smc91x: use run-time configuration on all ARM machines
The smc91x driver traditionally gets configured at compile-time
for whichever hardware it runs on. This no longer works on
ARM as we continue to move to building all-in-one kernels.

Most ARM configurations with this driver already use run-time
configuration through DT or through platform_data, but a
few have not been converted yet.

I've checked all ARM boards that use this driver in their
legacy board files, and converted the ones that were using
compile-time configuration in smc91x.h to behave like the
other ones and provide the interrupt polarity along with
the MMIO configuration (width, stride) at platform device
creation time.

In particular, these combinations were previously selectable
in Kconfig but in fact broken:

- sa1100 assabet plus pleb
- msm combined with any other armv6/v7 platform
- pxa-idp combined with any non-DMA pxa variant
- LogicPD PXA270 combined with any other pxa
- nomadik combined with any other armv4/v5 platform,
  e.g. versatile.

None of these seem critical enough to warrant a backport
to stable, but it would be nice to clean this up for good.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
----
I would like the patch to get merged through netdev, after
Robert and/or Linus have verified it on at least some hardware.

There are a few other non-ARM platforms using this driver,
I could do the same patch for those if we want to take
it further.

 arch/arm/mach-msm/board-halibut.c    |   8 ++++-
 arch/arm/mach-msm/board-qsd8x50.c    |   8 ++++-
 arch/arm/mach-pxa/idp.c              |   5 +++
 arch/arm/mach-pxa/lpd270.c           |   8 ++++-
 arch/arm/mach-realview/core.c        |   7 ++++
 arch/arm/mach-realview/realview_eb.c |   2 +-
 arch/arm/mach-sa1100/neponset.c      |   6 ++++
 arch/arm/mach-sa1100/pleb.c          |   7 ++++
 drivers/net/ethernet/smsc/smc91x.c   |   9 +++--
 drivers/net/ethernet/smsc/smc91x.h   | 114 ++----------------------------------------------------------
 10 files changed, 57 insertions(+), 117 deletions(-)
Tested-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
2015-02-28 12:56:56 -05:00

408 lines
10 KiB
C

/*
* linux/arch/arm/mach-realview/core.c
*
* Copyright (C) 1999 - 2003 ARM Limited
* Copyright (C) 2000 Deep Blue Solutions Ltd
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/dma-mapping.h>
#include <linux/device.h>
#include <linux/interrupt.h>
#include <linux/amba/bus.h>
#include <linux/amba/clcd.h>
#include <linux/platform_data/video-clcd-versatile.h>
#include <linux/io.h>
#include <linux/smsc911x.h>
#include <linux/smc91x.h>
#include <linux/ata_platform.h>
#include <linux/amba/mmci.h>
#include <linux/gfp.h>
#include <linux/mtd/physmap.h>
#include <linux/memblock.h>
#include <mach/hardware.h>
#include <asm/irq.h>
#include <asm/mach-types.h>
#include <asm/hardware/arm_timer.h>
#include <asm/hardware/icst.h>
#include <asm/mach/arch.h>
#include <asm/mach/irq.h>
#include <asm/mach/map.h>
#include <mach/platform.h>
#include <mach/irqs.h>
#include <asm/hardware/timer-sp.h>
#include <plat/sched_clock.h>
#include "core.h"
#define REALVIEW_FLASHCTRL (__io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_FLASH_OFFSET)
static void realview_flash_set_vpp(struct platform_device *pdev, int on)
{
u32 val;
val = __raw_readl(REALVIEW_FLASHCTRL);
if (on)
val |= REALVIEW_FLASHPROG_FLVPPEN;
else
val &= ~REALVIEW_FLASHPROG_FLVPPEN;
__raw_writel(val, REALVIEW_FLASHCTRL);
}
static struct physmap_flash_data realview_flash_data = {
.width = 4,
.set_vpp = realview_flash_set_vpp,
};
struct platform_device realview_flash_device = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &realview_flash_data,
},
};
int realview_flash_register(struct resource *res, u32 num)
{
realview_flash_device.resource = res;
realview_flash_device.num_resources = num;
return platform_device_register(&realview_flash_device);
}
static struct smsc911x_platform_config smsc911x_config = {
.flags = SMSC911X_USE_32BIT,
.irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_HIGH,
.irq_type = SMSC911X_IRQ_TYPE_PUSH_PULL,
.phy_interface = PHY_INTERFACE_MODE_MII,
};
static struct smc91x_platdata smc91x_platdata = {
.flags = SMC91X_USE_32BIT | SMC91X_NOWAIT,
};
static struct platform_device realview_eth_device = {
.name = "smsc911x",
.id = 0,
.num_resources = 2,
};
int realview_eth_register(const char *name, struct resource *res)
{
if (name)
realview_eth_device.name = name;
realview_eth_device.resource = res;
if (strcmp(realview_eth_device.name, "smsc911x") == 0)
realview_eth_device.dev.platform_data = &smsc911x_config;
else
realview_eth_device.dev.platform_data = &smc91x_platdata;
return platform_device_register(&realview_eth_device);
}
struct platform_device realview_usb_device = {
.name = "isp1760",
.num_resources = 2,
};
int realview_usb_register(struct resource *res)
{
realview_usb_device.resource = res;
return platform_device_register(&realview_usb_device);
}
static struct pata_platform_info pata_platform_data = {
.ioport_shift = 1,
};
static struct resource pata_resources[] = {
[0] = {
.start = REALVIEW_CF_BASE,
.end = REALVIEW_CF_BASE + 0xff,
.flags = IORESOURCE_MEM,
},
[1] = {
.start = REALVIEW_CF_BASE + 0x100,
.end = REALVIEW_CF_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
},
};
struct platform_device realview_cf_device = {
.name = "pata_platform",
.id = -1,
.num_resources = ARRAY_SIZE(pata_resources),
.resource = pata_resources,
.dev = {
.platform_data = &pata_platform_data,
},
};
static struct resource realview_leds_resources[] = {
{
.start = REALVIEW_SYS_BASE + REALVIEW_SYS_LED_OFFSET,
.end = REALVIEW_SYS_BASE + REALVIEW_SYS_LED_OFFSET + 4,
.flags = IORESOURCE_MEM,
},
};
struct platform_device realview_leds_device = {
.name = "versatile-leds",
.id = -1,
.num_resources = ARRAY_SIZE(realview_leds_resources),
.resource = realview_leds_resources,
};
static struct resource realview_i2c_resource = {
.start = REALVIEW_I2C_BASE,
.end = REALVIEW_I2C_BASE + SZ_4K - 1,
.flags = IORESOURCE_MEM,
};
struct platform_device realview_i2c_device = {
.name = "versatile-i2c",
.id = 0,
.num_resources = 1,
.resource = &realview_i2c_resource,
};
static struct i2c_board_info realview_i2c_board_info[] = {
{
I2C_BOARD_INFO("ds1338", 0xd0 >> 1),
},
};
static int __init realview_i2c_init(void)
{
return i2c_register_board_info(0, realview_i2c_board_info,
ARRAY_SIZE(realview_i2c_board_info));
}
arch_initcall(realview_i2c_init);
#define REALVIEW_SYSMCI (__io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_MCI_OFFSET)
/*
* This is only used if GPIOLIB support is disabled
*/
static unsigned int realview_mmc_status(struct device *dev)
{
struct amba_device *adev = container_of(dev, struct amba_device, dev);
u32 mask;
if (machine_is_realview_pb1176()) {
static bool inserted = false;
/*
* The PB1176 does not have the status register,
* assume it is inserted at startup, then invert
* for each call so card insertion/removal will
* be detected anyway. This will not be called if
* GPIO on PL061 is active, which is the proper
* way to do this on the PB1176.
*/
inserted = !inserted;
return inserted ? 0 : 1;
}
if (adev->res.start == REALVIEW_MMCI0_BASE)
mask = 1;
else
mask = 2;
return readl(REALVIEW_SYSMCI) & mask;
}
struct mmci_platform_data realview_mmc0_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = realview_mmc_status,
.gpio_wp = 17,
.gpio_cd = 16,
.cd_invert = true,
};
struct mmci_platform_data realview_mmc1_plat_data = {
.ocr_mask = MMC_VDD_32_33|MMC_VDD_33_34,
.status = realview_mmc_status,
.gpio_wp = 19,
.gpio_cd = 18,
.cd_invert = true,
};
void __init realview_init_early(void)
{
void __iomem *sys = __io_address(REALVIEW_SYS_BASE);
versatile_sched_clock_init(sys + REALVIEW_SYS_24MHz_OFFSET, 24000000);
}
/*
* CLCD support.
*/
#define SYS_CLCD_NLCDIOON (1 << 2)
#define SYS_CLCD_VDDPOSSWITCH (1 << 3)
#define SYS_CLCD_PWR3V5SWITCH (1 << 4)
#define SYS_CLCD_ID_MASK (0x1f << 8)
#define SYS_CLCD_ID_SANYO_3_8 (0x00 << 8)
#define SYS_CLCD_ID_UNKNOWN_8_4 (0x01 << 8)
#define SYS_CLCD_ID_EPSON_2_2 (0x02 << 8)
#define SYS_CLCD_ID_SANYO_2_5 (0x07 << 8)
#define SYS_CLCD_ID_VGA (0x1f << 8)
/*
* Disable all display connectors on the interface module.
*/
static void realview_clcd_disable(struct clcd_fb *fb)
{
void __iomem *sys_clcd = __io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_CLCD_OFFSET;
u32 val;
val = readl(sys_clcd);
val &= ~SYS_CLCD_NLCDIOON | SYS_CLCD_PWR3V5SWITCH;
writel(val, sys_clcd);
}
/*
* Enable the relevant connector on the interface module.
*/
static void realview_clcd_enable(struct clcd_fb *fb)
{
void __iomem *sys_clcd = __io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_CLCD_OFFSET;
u32 val;
/*
* Enable the PSUs
*/
val = readl(sys_clcd);
val |= SYS_CLCD_NLCDIOON | SYS_CLCD_PWR3V5SWITCH;
writel(val, sys_clcd);
}
/*
* Detect which LCD panel is connected, and return the appropriate
* clcd_panel structure. Note: we do not have any information on
* the required timings for the 8.4in panel, so we presently assume
* VGA timings.
*/
static int realview_clcd_setup(struct clcd_fb *fb)
{
void __iomem *sys_clcd = __io_address(REALVIEW_SYS_BASE) + REALVIEW_SYS_CLCD_OFFSET;
const char *panel_name, *vga_panel_name;
unsigned long framesize;
u32 val;
if (machine_is_realview_eb()) {
/* VGA, 16bpp */
framesize = 640 * 480 * 2;
vga_panel_name = "VGA";
} else {
/* XVGA, 16bpp */
framesize = 1024 * 768 * 2;
vga_panel_name = "XVGA";
}
val = readl(sys_clcd) & SYS_CLCD_ID_MASK;
if (val == SYS_CLCD_ID_SANYO_3_8)
panel_name = "Sanyo TM38QV67A02A";
else if (val == SYS_CLCD_ID_SANYO_2_5)
panel_name = "Sanyo QVGA Portrait";
else if (val == SYS_CLCD_ID_EPSON_2_2)
panel_name = "Epson L2F50113T00";
else if (val == SYS_CLCD_ID_VGA)
panel_name = vga_panel_name;
else {
pr_err("CLCD: unknown LCD panel ID 0x%08x, using VGA\n", val);
panel_name = vga_panel_name;
}
fb->panel = versatile_clcd_get_panel(panel_name);
if (!fb->panel)
return -EINVAL;
return versatile_clcd_setup_dma(fb, framesize);
}
struct clcd_board clcd_plat_data = {
.name = "RealView",
.caps = CLCD_CAP_ALL,
.check = clcdfb_check,
.decode = clcdfb_decode,
.disable = realview_clcd_disable,
.enable = realview_clcd_enable,
.setup = realview_clcd_setup,
.mmap = versatile_clcd_mmap_dma,
.remove = versatile_clcd_remove_dma,
};
/*
* Where is the timer (VA)?
*/
void __iomem *timer0_va_base;
void __iomem *timer1_va_base;
void __iomem *timer2_va_base;
void __iomem *timer3_va_base;
/*
* Set up the clock source and clock events devices
*/
void __init realview_timer_init(unsigned int timer_irq)
{
u32 val;
/*
* set clock frequency:
* REALVIEW_REFCLK is 32KHz
* REALVIEW_TIMCLK is 1MHz
*/
val = readl(__io_address(REALVIEW_SCTL_BASE));
writel((REALVIEW_TIMCLK << REALVIEW_TIMER1_EnSel) |
(REALVIEW_TIMCLK << REALVIEW_TIMER2_EnSel) |
(REALVIEW_TIMCLK << REALVIEW_TIMER3_EnSel) |
(REALVIEW_TIMCLK << REALVIEW_TIMER4_EnSel) | val,
__io_address(REALVIEW_SCTL_BASE));
/*
* Initialise to a known state (all timers off)
*/
writel(0, timer0_va_base + TIMER_CTRL);
writel(0, timer1_va_base + TIMER_CTRL);
writel(0, timer2_va_base + TIMER_CTRL);
writel(0, timer3_va_base + TIMER_CTRL);
sp804_clocksource_init(timer3_va_base, "timer3");
sp804_clockevents_init(timer0_va_base, timer_irq, "timer0");
}
/*
* Setup the memory banks.
*/
void realview_fixup(struct tag *tags, char **from)
{
/*
* Most RealView platforms have 512MB contiguous RAM at 0x70000000.
* Half of this is mirrored at 0.
*/
#ifdef CONFIG_REALVIEW_HIGH_PHYS_OFFSET
memblock_add(0x70000000, SZ_512M);
#else
memblock_add(0, SZ_256M);
#endif
}