linux/drivers/net/wireless/wl12xx/boot.h
Luciano Coelho afb7d3cd80 wl12xx: move hardcoded hci_io_ds value into the conf struct
Instead of hardcoding the hci_io_ds configuration that we write to the
SDIO_IO_DS top registed, read it from the default configuration so
that it's easier to change for different platforms.

Reported-by: Ido Yariv <ido@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
2011-04-19 16:49:22 +03:00

130 lines
3.7 KiB
C

/*
* This file is part of wl1271
*
* Copyright (C) 2008-2009 Nokia Corporation
*
* Contact: Luciano Coelho <luciano.coelho@nokia.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
* 02110-1301 USA
*
*/
#ifndef __BOOT_H__
#define __BOOT_H__
#include "wl12xx.h"
int wl1271_boot(struct wl1271 *wl);
int wl1271_load_firmware(struct wl1271 *wl);
#define WL1271_NO_SUBBANDS 8
#define WL1271_NO_POWER_LEVELS 4
#define WL1271_FW_VERSION_MAX_LEN 20
struct wl1271_static_data {
u8 mac_address[ETH_ALEN];
u8 padding[2];
u8 fw_version[WL1271_FW_VERSION_MAX_LEN];
u32 hw_version;
u8 tx_power_table[WL1271_NO_SUBBANDS][WL1271_NO_POWER_LEVELS];
};
/* number of times we try to read the INIT interrupt */
#define INIT_LOOP 20000
/* delay between retries */
#define INIT_LOOP_DELAY 50
#define WU_COUNTER_PAUSE_VAL 0x3FF
#define WELP_ARM_COMMAND_VAL 0x4
#define OCP_REG_POLARITY 0x0064
#define OCP_REG_CLK_TYPE 0x0448
#define OCP_REG_CLK_POLARITY 0x0cb2
#define OCP_REG_CLK_PULL 0x0cb4
#define REG_FUSE_DATA_2_1 0x050a
#define PG_VER_MASK 0x3c
#define PG_VER_OFFSET 2
#define PG_MAJOR_VER_MASK 0x3
#define PG_MAJOR_VER_OFFSET 0x0
#define PG_MINOR_VER_MASK 0xc
#define PG_MINOR_VER_OFFSET 0x2
#define CMD_MBOX_ADDRESS 0x407B4
#define POLARITY_LOW BIT(1)
#define NO_PULL (BIT(14) | BIT(15))
#define FREF_CLK_TYPE_BITS 0xfffffe7f
#define CLK_REQ_PRCM 0x100
#define FREF_CLK_POLARITY_BITS 0xfffff8ff
#define CLK_REQ_OUTN_SEL 0x700
/* PLL configuration algorithm for wl128x */
#define SYS_CLK_CFG_REG 0x2200
/* Bit[0] - 0-TCXO, 1-FREF */
#define MCS_PLL_CLK_SEL_FREF BIT(0)
/* Bit[3:2] - 01-TCXO, 10-FREF */
#define WL_CLK_REQ_TYPE_FREF BIT(3)
#define WL_CLK_REQ_TYPE_PG2 (BIT(3) | BIT(2))
/* Bit[4] - 0-TCXO, 1-FREF */
#define PRCM_CM_EN_MUX_WLAN_FREF BIT(4)
#define TCXO_ILOAD_INT_REG 0x2264
#define TCXO_CLK_DETECT_REG 0x2266
#define TCXO_DET_FAILED BIT(4)
#define FREF_ILOAD_INT_REG 0x2084
#define FREF_CLK_DETECT_REG 0x2086
#define FREF_CLK_DETECT_FAIL BIT(4)
/* Use this reg for masking during driver access */
#define WL_SPARE_REG 0x2320
#define WL_SPARE_VAL BIT(2)
/* Bit[6:5:3] - mask wl write SYS_CLK_CFG[8:5:2:4] */
#define WL_SPARE_MASK_8526 (BIT(6) | BIT(5) | BIT(3))
#define PLL_LOCK_COUNTERS_REG 0xD8C
#define PLL_LOCK_COUNTERS_COEX 0x0F
#define PLL_LOCK_COUNTERS_MCS 0xF0
#define MCS_PLL_OVERRIDE_REG 0xD90
#define MCS_PLL_CONFIG_REG 0xD92
#define MCS_SEL_IN_FREQ_MASK 0x0070
#define MCS_SEL_IN_FREQ_SHIFT 4
#define MCS_PLL_CONFIG_REG_VAL 0x73
#define MCS_PLL_ENABLE_HP (BIT(0) | BIT(1))
#define MCS_PLL_M_REG 0xD94
#define MCS_PLL_N_REG 0xD96
#define MCS_PLL_M_REG_VAL 0xC8
#define MCS_PLL_N_REG_VAL 0x07
#define SDIO_IO_DS 0xd14
/* SDIO/wSPI DS configuration values */
enum {
HCI_IO_DS_8MA = 0,
HCI_IO_DS_4MA = 1, /* default */
HCI_IO_DS_6MA = 2,
HCI_IO_DS_2MA = 3,
};
/* end PLL configuration algorithm for wl128x */
#endif