linux/drivers/spi/spi-sprd-adi.c
Rob Herring 749396cb29
spi: Explicitly include correct DT includes
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.

Signed-off-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20230714174955.4064174-1-robh@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
2023-07-14 20:53:00 +01:00

667 lines
17 KiB
C

/*
* Copyright (C) 2017 Spreadtrum Communications Inc.
*
* SPDX-License-Identifier: GPL-2.0
*/
#include <linux/delay.h>
#include <linux/hwspinlock.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/reboot.h>
#include <linux/spi/spi.h>
#include <linux/sizes.h>
/* Registers definitions for ADI controller */
#define REG_ADI_CTRL0 0x4
#define REG_ADI_CHN_PRIL 0x8
#define REG_ADI_CHN_PRIH 0xc
#define REG_ADI_INT_EN 0x10
#define REG_ADI_INT_RAW 0x14
#define REG_ADI_INT_MASK 0x18
#define REG_ADI_INT_CLR 0x1c
#define REG_ADI_GSSI_CFG0 0x20
#define REG_ADI_GSSI_CFG1 0x24
#define REG_ADI_RD_CMD 0x28
#define REG_ADI_RD_DATA 0x2c
#define REG_ADI_ARM_FIFO_STS 0x30
#define REG_ADI_STS 0x34
#define REG_ADI_EVT_FIFO_STS 0x38
#define REG_ADI_ARM_CMD_STS 0x3c
#define REG_ADI_CHN_EN 0x40
#define REG_ADI_CHN_ADDR(id) (0x44 + (id - 2) * 4)
#define REG_ADI_CHN_EN1 0x20c
/* Bits definitions for register REG_ADI_GSSI_CFG0 */
#define BIT_CLK_ALL_ON BIT(30)
/* Bits definitions for register REG_ADI_RD_DATA */
#define BIT_RD_CMD_BUSY BIT(31)
#define RD_ADDR_SHIFT 16
#define RD_VALUE_MASK GENMASK(15, 0)
#define RD_ADDR_MASK GENMASK(30, 16)
/* Bits definitions for register REG_ADI_ARM_FIFO_STS */
#define BIT_FIFO_FULL BIT(11)
#define BIT_FIFO_EMPTY BIT(10)
/*
* ADI slave devices include RTC, ADC, regulator, charger, thermal and so on.
* ADI supports 12/14bit address for r2p0, and additional 17bit for r3p0 or
* later versions. Since bit[1:0] are zero, so the spec describe them as
* 10/12/15bit address mode.
* The 10bit mode supports sigle slave, 12/15bit mode supports 3 slave, the
* high two bits is slave_id.
* The slave devices address offset is 0x8000 for 10/12bit address mode,
* and 0x20000 for 15bit mode.
*/
#define ADI_10BIT_SLAVE_ADDR_SIZE SZ_4K
#define ADI_10BIT_SLAVE_OFFSET 0x8000
#define ADI_12BIT_SLAVE_ADDR_SIZE SZ_16K
#define ADI_12BIT_SLAVE_OFFSET 0x8000
#define ADI_15BIT_SLAVE_ADDR_SIZE SZ_128K
#define ADI_15BIT_SLAVE_OFFSET 0x20000
/* Timeout (ms) for the trylock of hardware spinlocks */
#define ADI_HWSPINLOCK_TIMEOUT 5000
/*
* ADI controller has 50 channels including 2 software channels
* and 48 hardware channels.
*/
#define ADI_HW_CHNS 50
#define ADI_FIFO_DRAIN_TIMEOUT 1000
#define ADI_READ_TIMEOUT 2000
/*
* Read back address from REG_ADI_RD_DATA bit[30:16] which maps to:
* REG_ADI_RD_CMD bit[14:0] for r2p0
* REG_ADI_RD_CMD bit[16:2] for r3p0
*/
#define RDBACK_ADDR_MASK_R2 GENMASK(14, 0)
#define RDBACK_ADDR_MASK_R3 GENMASK(16, 2)
#define RDBACK_ADDR_SHIFT_R3 2
/* Registers definitions for PMIC watchdog controller */
#define REG_WDG_LOAD_LOW 0x0
#define REG_WDG_LOAD_HIGH 0x4
#define REG_WDG_CTRL 0x8
#define REG_WDG_LOCK 0x20
/* Bits definitions for register REG_WDG_CTRL */
#define BIT_WDG_RUN BIT(1)
#define BIT_WDG_NEW BIT(2)
#define BIT_WDG_RST BIT(3)
/* Bits definitions for register REG_MODULE_EN */
#define BIT_WDG_EN BIT(2)
/* Registers definitions for PMIC */
#define PMIC_RST_STATUS 0xee8
#define PMIC_MODULE_EN 0xc08
#define PMIC_CLK_EN 0xc18
#define PMIC_WDG_BASE 0x80
/* Definition of PMIC reset status register */
#define HWRST_STATUS_SECURITY 0x02
#define HWRST_STATUS_RECOVERY 0x20
#define HWRST_STATUS_NORMAL 0x40
#define HWRST_STATUS_ALARM 0x50
#define HWRST_STATUS_SLEEP 0x60
#define HWRST_STATUS_FASTBOOT 0x30
#define HWRST_STATUS_SPECIAL 0x70
#define HWRST_STATUS_PANIC 0x80
#define HWRST_STATUS_CFTREBOOT 0x90
#define HWRST_STATUS_AUTODLOADER 0xa0
#define HWRST_STATUS_IQMODE 0xb0
#define HWRST_STATUS_SPRDISK 0xc0
#define HWRST_STATUS_FACTORYTEST 0xe0
#define HWRST_STATUS_WATCHDOG 0xf0
/* Use default timeout 50 ms that converts to watchdog values */
#define WDG_LOAD_VAL ((50 * 32768) / 1000)
#define WDG_LOAD_MASK GENMASK(15, 0)
#define WDG_UNLOCK_KEY 0xe551
struct sprd_adi_wdg {
u32 base;
u32 rst_sts;
u32 wdg_en;
u32 wdg_clk;
};
struct sprd_adi_data {
u32 slave_offset;
u32 slave_addr_size;
int (*read_check)(u32 val, u32 reg);
int (*restart)(struct notifier_block *this,
unsigned long mode, void *cmd);
void (*wdg_rst)(void *p);
};
struct sprd_adi {
struct spi_controller *ctlr;
struct device *dev;
void __iomem *base;
struct hwspinlock *hwlock;
unsigned long slave_vbase;
unsigned long slave_pbase;
struct notifier_block restart_handler;
const struct sprd_adi_data *data;
};
static int sprd_adi_check_addr(struct sprd_adi *sadi, u32 reg)
{
if (reg >= sadi->data->slave_addr_size) {
dev_err(sadi->dev,
"slave address offset is incorrect, reg = 0x%x\n",
reg);
return -EINVAL;
}
return 0;
}
static int sprd_adi_drain_fifo(struct sprd_adi *sadi)
{
u32 timeout = ADI_FIFO_DRAIN_TIMEOUT;
u32 sts;
do {
sts = readl_relaxed(sadi->base + REG_ADI_ARM_FIFO_STS);
if (sts & BIT_FIFO_EMPTY)
break;
cpu_relax();
} while (--timeout);
if (timeout == 0) {
dev_err(sadi->dev, "drain write fifo timeout\n");
return -EBUSY;
}
return 0;
}
static int sprd_adi_fifo_is_full(struct sprd_adi *sadi)
{
return readl_relaxed(sadi->base + REG_ADI_ARM_FIFO_STS) & BIT_FIFO_FULL;
}
static int sprd_adi_read_check(u32 val, u32 addr)
{
u32 rd_addr;
rd_addr = (val & RD_ADDR_MASK) >> RD_ADDR_SHIFT;
if (rd_addr != addr) {
pr_err("ADI read error, addr = 0x%x, val = 0x%x\n", addr, val);
return -EIO;
}
return 0;
}
static int sprd_adi_read_check_r2(u32 val, u32 reg)
{
return sprd_adi_read_check(val, reg & RDBACK_ADDR_MASK_R2);
}
static int sprd_adi_read_check_r3(u32 val, u32 reg)
{
return sprd_adi_read_check(val, (reg & RDBACK_ADDR_MASK_R3) >> RDBACK_ADDR_SHIFT_R3);
}
static int sprd_adi_read(struct sprd_adi *sadi, u32 reg, u32 *read_val)
{
int read_timeout = ADI_READ_TIMEOUT;
unsigned long flags;
u32 val;
int ret = 0;
if (sadi->hwlock) {
ret = hwspin_lock_timeout_irqsave(sadi->hwlock,
ADI_HWSPINLOCK_TIMEOUT,
&flags);
if (ret) {
dev_err(sadi->dev, "get the hw lock failed\n");
return ret;
}
}
ret = sprd_adi_check_addr(sadi, reg);
if (ret)
goto out;
/*
* Set the slave address offset need to read into RD_CMD register,
* then ADI controller will start to transfer automatically.
*/
writel_relaxed(reg, sadi->base + REG_ADI_RD_CMD);
/*
* Wait read operation complete, the BIT_RD_CMD_BUSY will be set
* simultaneously when writing read command to register, and the
* BIT_RD_CMD_BUSY will be cleared after the read operation is
* completed.
*/
do {
val = readl_relaxed(sadi->base + REG_ADI_RD_DATA);
if (!(val & BIT_RD_CMD_BUSY))
break;
cpu_relax();
} while (--read_timeout);
if (read_timeout == 0) {
dev_err(sadi->dev, "ADI read timeout\n");
ret = -EBUSY;
goto out;
}
/*
* The return value before adi r5p0 includes data and read register
* address, from bit 0to bit 15 are data, and from bit 16 to bit 30
* are read register address. Then we can check the returned register
* address to validate data.
*/
if (sadi->data->read_check) {
ret = sadi->data->read_check(val, reg);
if (ret < 0)
goto out;
}
*read_val = val & RD_VALUE_MASK;
out:
if (sadi->hwlock)
hwspin_unlock_irqrestore(sadi->hwlock, &flags);
return ret;
}
static int sprd_adi_write(struct sprd_adi *sadi, u32 reg, u32 val)
{
u32 timeout = ADI_FIFO_DRAIN_TIMEOUT;
unsigned long flags;
int ret;
if (sadi->hwlock) {
ret = hwspin_lock_timeout_irqsave(sadi->hwlock,
ADI_HWSPINLOCK_TIMEOUT,
&flags);
if (ret) {
dev_err(sadi->dev, "get the hw lock failed\n");
return ret;
}
}
ret = sprd_adi_check_addr(sadi, reg);
if (ret)
goto out;
ret = sprd_adi_drain_fifo(sadi);
if (ret < 0)
goto out;
/*
* we should wait for write fifo is empty before writing data to PMIC
* registers.
*/
do {
if (!sprd_adi_fifo_is_full(sadi)) {
/* we need virtual register address to write. */
writel_relaxed(val, (void __iomem *)(sadi->slave_vbase + reg));
break;
}
cpu_relax();
} while (--timeout);
if (timeout == 0) {
dev_err(sadi->dev, "write fifo is full\n");
ret = -EBUSY;
}
out:
if (sadi->hwlock)
hwspin_unlock_irqrestore(sadi->hwlock, &flags);
return ret;
}
static int sprd_adi_transfer_one(struct spi_controller *ctlr,
struct spi_device *spi_dev,
struct spi_transfer *t)
{
struct sprd_adi *sadi = spi_controller_get_devdata(ctlr);
u32 reg, val;
int ret;
if (t->rx_buf) {
reg = *(u32 *)t->rx_buf;
ret = sprd_adi_read(sadi, reg, &val);
*(u32 *)t->rx_buf = val;
} else if (t->tx_buf) {
u32 *p = (u32 *)t->tx_buf;
reg = *p++;
val = *p;
ret = sprd_adi_write(sadi, reg, val);
} else {
dev_err(sadi->dev, "no buffer for transfer\n");
ret = -EINVAL;
}
return ret;
}
static void sprd_adi_set_wdt_rst_mode(void *p)
{
#if IS_ENABLED(CONFIG_SPRD_WATCHDOG)
u32 val;
struct sprd_adi *sadi = (struct sprd_adi *)p;
/* Init watchdog reset mode */
sprd_adi_read(sadi, PMIC_RST_STATUS, &val);
val |= HWRST_STATUS_WATCHDOG;
sprd_adi_write(sadi, PMIC_RST_STATUS, val);
#endif
}
static int sprd_adi_restart(struct notifier_block *this, unsigned long mode,
void *cmd, struct sprd_adi_wdg *wdg)
{
struct sprd_adi *sadi = container_of(this, struct sprd_adi,
restart_handler);
u32 val, reboot_mode = 0;
if (!cmd)
reboot_mode = HWRST_STATUS_NORMAL;
else if (!strncmp(cmd, "recovery", 8))
reboot_mode = HWRST_STATUS_RECOVERY;
else if (!strncmp(cmd, "alarm", 5))
reboot_mode = HWRST_STATUS_ALARM;
else if (!strncmp(cmd, "fastsleep", 9))
reboot_mode = HWRST_STATUS_SLEEP;
else if (!strncmp(cmd, "bootloader", 10))
reboot_mode = HWRST_STATUS_FASTBOOT;
else if (!strncmp(cmd, "panic", 5))
reboot_mode = HWRST_STATUS_PANIC;
else if (!strncmp(cmd, "special", 7))
reboot_mode = HWRST_STATUS_SPECIAL;
else if (!strncmp(cmd, "cftreboot", 9))
reboot_mode = HWRST_STATUS_CFTREBOOT;
else if (!strncmp(cmd, "autodloader", 11))
reboot_mode = HWRST_STATUS_AUTODLOADER;
else if (!strncmp(cmd, "iqmode", 6))
reboot_mode = HWRST_STATUS_IQMODE;
else if (!strncmp(cmd, "sprdisk", 7))
reboot_mode = HWRST_STATUS_SPRDISK;
else if (!strncmp(cmd, "tospanic", 8))
reboot_mode = HWRST_STATUS_SECURITY;
else if (!strncmp(cmd, "factorytest", 11))
reboot_mode = HWRST_STATUS_FACTORYTEST;
else
reboot_mode = HWRST_STATUS_NORMAL;
/* Record the reboot mode */
sprd_adi_read(sadi, wdg->rst_sts, &val);
val &= ~HWRST_STATUS_WATCHDOG;
val |= reboot_mode;
sprd_adi_write(sadi, wdg->rst_sts, val);
/* Enable the interface clock of the watchdog */
sprd_adi_read(sadi, wdg->wdg_en, &val);
val |= BIT_WDG_EN;
sprd_adi_write(sadi, wdg->wdg_en, val);
/* Enable the work clock of the watchdog */
sprd_adi_read(sadi, wdg->wdg_clk, &val);
val |= BIT_WDG_EN;
sprd_adi_write(sadi, wdg->wdg_clk, val);
/* Unlock the watchdog */
sprd_adi_write(sadi, wdg->base + REG_WDG_LOCK, WDG_UNLOCK_KEY);
sprd_adi_read(sadi, wdg->base + REG_WDG_CTRL, &val);
val |= BIT_WDG_NEW;
sprd_adi_write(sadi, wdg->base + REG_WDG_CTRL, val);
/* Load the watchdog timeout value, 50ms is always enough. */
sprd_adi_write(sadi, wdg->base + REG_WDG_LOAD_HIGH, 0);
sprd_adi_write(sadi, wdg->base + REG_WDG_LOAD_LOW,
WDG_LOAD_VAL & WDG_LOAD_MASK);
/* Start the watchdog to reset system */
sprd_adi_read(sadi, wdg->base + REG_WDG_CTRL, &val);
val |= BIT_WDG_RUN | BIT_WDG_RST;
sprd_adi_write(sadi, wdg->base + REG_WDG_CTRL, val);
/* Lock the watchdog */
sprd_adi_write(sadi, wdg->base + REG_WDG_LOCK, ~WDG_UNLOCK_KEY);
mdelay(1000);
dev_emerg(sadi->dev, "Unable to restart system\n");
return NOTIFY_DONE;
}
static int sprd_adi_restart_sc9860(struct notifier_block *this,
unsigned long mode, void *cmd)
{
struct sprd_adi_wdg wdg = {
.base = PMIC_WDG_BASE,
.rst_sts = PMIC_RST_STATUS,
.wdg_en = PMIC_MODULE_EN,
.wdg_clk = PMIC_CLK_EN,
};
return sprd_adi_restart(this, mode, cmd, &wdg);
}
static void sprd_adi_hw_init(struct sprd_adi *sadi)
{
struct device_node *np = sadi->dev->of_node;
int i, size, chn_cnt;
const __be32 *list;
u32 tmp;
/* Set all channels as default priority */
writel_relaxed(0, sadi->base + REG_ADI_CHN_PRIL);
writel_relaxed(0, sadi->base + REG_ADI_CHN_PRIH);
/* Set clock auto gate mode */
tmp = readl_relaxed(sadi->base + REG_ADI_GSSI_CFG0);
tmp &= ~BIT_CLK_ALL_ON;
writel_relaxed(tmp, sadi->base + REG_ADI_GSSI_CFG0);
/* Set hardware channels setting */
list = of_get_property(np, "sprd,hw-channels", &size);
if (!list || !size) {
dev_info(sadi->dev, "no hw channels setting in node\n");
return;
}
chn_cnt = size / 8;
for (i = 0; i < chn_cnt; i++) {
u32 value;
u32 chn_id = be32_to_cpu(*list++);
u32 chn_config = be32_to_cpu(*list++);
/* Channel 0 and 1 are software channels */
if (chn_id < 2)
continue;
writel_relaxed(chn_config, sadi->base +
REG_ADI_CHN_ADDR(chn_id));
if (chn_id < 32) {
value = readl_relaxed(sadi->base + REG_ADI_CHN_EN);
value |= BIT(chn_id);
writel_relaxed(value, sadi->base + REG_ADI_CHN_EN);
} else if (chn_id < ADI_HW_CHNS) {
value = readl_relaxed(sadi->base + REG_ADI_CHN_EN1);
value |= BIT(chn_id - 32);
writel_relaxed(value, sadi->base + REG_ADI_CHN_EN1);
}
}
}
static int sprd_adi_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
const struct sprd_adi_data *data;
struct spi_controller *ctlr;
struct sprd_adi *sadi;
struct resource *res;
u16 num_chipselect;
int ret;
if (!np) {
dev_err(&pdev->dev, "can not find the adi bus node\n");
return -ENODEV;
}
data = of_device_get_match_data(&pdev->dev);
if (!data) {
dev_err(&pdev->dev, "no matching driver data found\n");
return -EINVAL;
}
pdev->id = of_alias_get_id(np, "spi");
num_chipselect = of_get_child_count(np);
ctlr = spi_alloc_master(&pdev->dev, sizeof(struct sprd_adi));
if (!ctlr)
return -ENOMEM;
dev_set_drvdata(&pdev->dev, ctlr);
sadi = spi_controller_get_devdata(ctlr);
sadi->base = devm_platform_get_and_ioremap_resource(pdev, 0, &res);
if (IS_ERR(sadi->base)) {
ret = PTR_ERR(sadi->base);
goto put_ctlr;
}
sadi->slave_vbase = (unsigned long)sadi->base +
data->slave_offset;
sadi->slave_pbase = res->start + data->slave_offset;
sadi->ctlr = ctlr;
sadi->dev = &pdev->dev;
sadi->data = data;
ret = of_hwspin_lock_get_id(np, 0);
if (ret > 0 || (IS_ENABLED(CONFIG_HWSPINLOCK) && ret == 0)) {
sadi->hwlock =
devm_hwspin_lock_request_specific(&pdev->dev, ret);
if (!sadi->hwlock) {
ret = -ENXIO;
goto put_ctlr;
}
} else {
switch (ret) {
case -ENOENT:
dev_info(&pdev->dev, "no hardware spinlock supplied\n");
break;
default:
dev_err_probe(&pdev->dev, ret, "failed to find hwlock id\n");
goto put_ctlr;
}
}
sprd_adi_hw_init(sadi);
if (sadi->data->wdg_rst)
sadi->data->wdg_rst(sadi);
ctlr->dev.of_node = pdev->dev.of_node;
ctlr->bus_num = pdev->id;
ctlr->num_chipselect = num_chipselect;
ctlr->flags = SPI_CONTROLLER_HALF_DUPLEX;
ctlr->bits_per_word_mask = 0;
ctlr->transfer_one = sprd_adi_transfer_one;
ret = devm_spi_register_controller(&pdev->dev, ctlr);
if (ret) {
dev_err(&pdev->dev, "failed to register SPI controller\n");
goto put_ctlr;
}
if (sadi->data->restart) {
sadi->restart_handler.notifier_call = sadi->data->restart;
sadi->restart_handler.priority = 128;
ret = register_restart_handler(&sadi->restart_handler);
if (ret) {
dev_err(&pdev->dev, "can not register restart handler\n");
goto put_ctlr;
}
}
return 0;
put_ctlr:
spi_controller_put(ctlr);
return ret;
}
static void sprd_adi_remove(struct platform_device *pdev)
{
struct spi_controller *ctlr = dev_get_drvdata(&pdev->dev);
struct sprd_adi *sadi = spi_controller_get_devdata(ctlr);
unregister_restart_handler(&sadi->restart_handler);
}
static struct sprd_adi_data sc9860_data = {
.slave_offset = ADI_10BIT_SLAVE_OFFSET,
.slave_addr_size = ADI_10BIT_SLAVE_ADDR_SIZE,
.read_check = sprd_adi_read_check_r2,
.restart = sprd_adi_restart_sc9860,
.wdg_rst = sprd_adi_set_wdt_rst_mode,
};
static struct sprd_adi_data sc9863_data = {
.slave_offset = ADI_12BIT_SLAVE_OFFSET,
.slave_addr_size = ADI_12BIT_SLAVE_ADDR_SIZE,
.read_check = sprd_adi_read_check_r3,
};
static struct sprd_adi_data ums512_data = {
.slave_offset = ADI_15BIT_SLAVE_OFFSET,
.slave_addr_size = ADI_15BIT_SLAVE_ADDR_SIZE,
.read_check = sprd_adi_read_check_r3,
};
static const struct of_device_id sprd_adi_of_match[] = {
{
.compatible = "sprd,sc9860-adi",
.data = &sc9860_data,
},
{
.compatible = "sprd,sc9863-adi",
.data = &sc9863_data,
},
{
.compatible = "sprd,ums512-adi",
.data = &ums512_data,
},
{ },
};
MODULE_DEVICE_TABLE(of, sprd_adi_of_match);
static struct platform_driver sprd_adi_driver = {
.driver = {
.name = "sprd-adi",
.of_match_table = sprd_adi_of_match,
},
.probe = sprd_adi_probe,
.remove_new = sprd_adi_remove,
};
module_platform_driver(sprd_adi_driver);
MODULE_DESCRIPTION("Spreadtrum ADI Controller Driver");
MODULE_AUTHOR("Baolin Wang <Baolin.Wang@spreadtrum.com>");
MODULE_LICENSE("GPL v2");