linux/arch/arm/mach-orion5x/ts209-setup.c
Linus Torvalds 1fdb24e969 Merge branch 'devel-stable' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm
* 'devel-stable' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm: (178 commits)
  ARM: 7139/1: fix compilation with CONFIG_ARM_ATAG_DTB_COMPAT and large TEXT_OFFSET
  ARM: gic, local timers: use the request_percpu_irq() interface
  ARM: gic: consolidate PPI handling
  ARM: switch from NO_MACH_MEMORY_H to NEED_MACH_MEMORY_H
  ARM: mach-s5p64x0: remove mach/memory.h
  ARM: mach-s3c64xx: remove mach/memory.h
  ARM: plat-mxc: remove mach/memory.h
  ARM: mach-prima2: remove mach/memory.h
  ARM: mach-zynq: remove mach/memory.h
  ARM: mach-bcmring: remove mach/memory.h
  ARM: mach-davinci: remove mach/memory.h
  ARM: mach-pxa: remove mach/memory.h
  ARM: mach-ixp4xx: remove mach/memory.h
  ARM: mach-h720x: remove mach/memory.h
  ARM: mach-vt8500: remove mach/memory.h
  ARM: mach-s5pc100: remove mach/memory.h
  ARM: mach-tegra: remove mach/memory.h
  ARM: plat-tcc: remove mach/memory.h
  ARM: mach-mmp: remove mach/memory.h
  ARM: mach-cns3xxx: remove mach/memory.h
  ...

Fix up mostly pretty trivial conflicts in:
 - arch/arm/Kconfig
 - arch/arm/include/asm/localtimer.h
 - arch/arm/kernel/Makefile
 - arch/arm/mach-shmobile/board-ap4evb.c
 - arch/arm/mach-u300/core.c
 - arch/arm/mm/dma-mapping.c
 - arch/arm/mm/proc-v7.S
 - arch/arm/plat-omap/Kconfig
largely due to some CONFIG option renaming (ie CONFIG_PM_SLEEP ->
CONFIG_ARM_CPU_SUSPEND for the arm-specific suspend code etc) and
addition of NEED_MACH_MEMORY_H next to HAVE_IDE.
2011-10-28 12:02:27 -07:00

333 lines
8.6 KiB
C

/*
* QNAP TS-109/TS-209 Board Setup
*
* Maintainer: Byron Bradley <byron.bbradley@gmail.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version
* 2 of the License, or (at your option) any later version.
*/
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/pci.h>
#include <linux/irq.h>
#include <linux/mtd/physmap.h>
#include <linux/mtd/nand.h>
#include <linux/mv643xx_eth.h>
#include <linux/gpio_keys.h>
#include <linux/input.h>
#include <linux/i2c.h>
#include <linux/serial_reg.h>
#include <linux/ata_platform.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/pci.h>
#include <mach/orion5x.h>
#include "common.h"
#include "mpp.h"
#include "tsx09-common.h"
#define QNAP_TS209_NOR_BOOT_BASE 0xf4000000
#define QNAP_TS209_NOR_BOOT_SIZE SZ_8M
/****************************************************************************
* 8MiB NOR flash. The struct mtd_partition is not in the same order as the
* partitions on the device because we want to keep compatibility with
* existing QNAP firmware.
*
* Layout as used by QNAP:
* [2] 0x00000000-0x00200000 : "Kernel"
* [3] 0x00200000-0x00600000 : "RootFS1"
* [4] 0x00600000-0x00700000 : "RootFS2"
* [6] 0x00700000-0x00760000 : "NAS Config" (read-only)
* [5] 0x00760000-0x00780000 : "U-Boot Config"
* [1] 0x00780000-0x00800000 : "U-Boot" (read-only)
***************************************************************************/
static struct mtd_partition qnap_ts209_partitions[] = {
{
.name = "U-Boot",
.size = 0x00080000,
.offset = 0x00780000,
.mask_flags = MTD_WRITEABLE,
}, {
.name = "Kernel",
.size = 0x00200000,
.offset = 0,
}, {
.name = "RootFS1",
.size = 0x00400000,
.offset = 0x00200000,
}, {
.name = "RootFS2",
.size = 0x00100000,
.offset = 0x00600000,
}, {
.name = "U-Boot Config",
.size = 0x00020000,
.offset = 0x00760000,
}, {
.name = "NAS Config",
.size = 0x00060000,
.offset = 0x00700000,
.mask_flags = MTD_WRITEABLE,
},
};
static struct physmap_flash_data qnap_ts209_nor_flash_data = {
.width = 1,
.parts = qnap_ts209_partitions,
.nr_parts = ARRAY_SIZE(qnap_ts209_partitions)
};
static struct resource qnap_ts209_nor_flash_resource = {
.flags = IORESOURCE_MEM,
.start = QNAP_TS209_NOR_BOOT_BASE,
.end = QNAP_TS209_NOR_BOOT_BASE + QNAP_TS209_NOR_BOOT_SIZE - 1,
};
static struct platform_device qnap_ts209_nor_flash = {
.name = "physmap-flash",
.id = 0,
.dev = {
.platform_data = &qnap_ts209_nor_flash_data,
},
.resource = &qnap_ts209_nor_flash_resource,
.num_resources = 1,
};
/*****************************************************************************
* PCI
****************************************************************************/
#define QNAP_TS209_PCI_SLOT0_OFFS 7
#define QNAP_TS209_PCI_SLOT0_IRQ_PIN 6
#define QNAP_TS209_PCI_SLOT1_IRQ_PIN 7
void __init qnap_ts209_pci_preinit(void)
{
int pin;
/*
* Configure PCI GPIO IRQ pins
*/
pin = QNAP_TS209_PCI_SLOT0_IRQ_PIN;
if (gpio_request(pin, "PCI Int1") == 0) {
if (gpio_direction_input(pin) == 0) {
irq_set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW);
} else {
printk(KERN_ERR "qnap_ts209_pci_preinit failed to "
"set_irq_type pin %d\n", pin);
gpio_free(pin);
}
} else {
printk(KERN_ERR "qnap_ts209_pci_preinit failed to gpio_request "
"%d\n", pin);
}
pin = QNAP_TS209_PCI_SLOT1_IRQ_PIN;
if (gpio_request(pin, "PCI Int2") == 0) {
if (gpio_direction_input(pin) == 0) {
irq_set_irq_type(gpio_to_irq(pin), IRQ_TYPE_LEVEL_LOW);
} else {
printk(KERN_ERR "qnap_ts209_pci_preinit failed "
"to set_irq_type pin %d\n", pin);
gpio_free(pin);
}
} else {
printk(KERN_ERR "qnap_ts209_pci_preinit failed to gpio_request "
"%d\n", pin);
}
}
static int __init qnap_ts209_pci_map_irq(const struct pci_dev *dev, u8 slot,
u8 pin)
{
int irq;
/*
* Check for devices with hard-wired IRQs.
*/
irq = orion5x_pci_map_irq(dev, slot, pin);
if (irq != -1)
return irq;
/*
* PCI IRQs are connected via GPIOs.
*/
switch (slot - QNAP_TS209_PCI_SLOT0_OFFS) {
case 0:
return gpio_to_irq(QNAP_TS209_PCI_SLOT0_IRQ_PIN);
case 1:
return gpio_to_irq(QNAP_TS209_PCI_SLOT1_IRQ_PIN);
default:
return -1;
}
}
static struct hw_pci qnap_ts209_pci __initdata = {
.nr_controllers = 2,
.preinit = qnap_ts209_pci_preinit,
.swizzle = pci_std_swizzle,
.setup = orion5x_pci_sys_setup,
.scan = orion5x_pci_sys_scan_bus,
.map_irq = qnap_ts209_pci_map_irq,
};
static int __init qnap_ts209_pci_init(void)
{
if (machine_is_ts_x09())
pci_common_init(&qnap_ts209_pci);
return 0;
}
subsys_initcall(qnap_ts209_pci_init);
/*****************************************************************************
* RTC S35390A on I2C bus
****************************************************************************/
#define TS209_RTC_GPIO 3
static struct i2c_board_info __initdata qnap_ts209_i2c_rtc = {
I2C_BOARD_INFO("s35390a", 0x30),
.irq = 0,
};
/****************************************************************************
* GPIO Attached Keys
* Power button is attached to the PIC microcontroller
****************************************************************************/
#define QNAP_TS209_GPIO_KEY_MEDIA 1
#define QNAP_TS209_GPIO_KEY_RESET 2
static struct gpio_keys_button qnap_ts209_buttons[] = {
{
.code = KEY_COPY,
.gpio = QNAP_TS209_GPIO_KEY_MEDIA,
.desc = "USB Copy Button",
.active_low = 1,
}, {
.code = KEY_RESTART,
.gpio = QNAP_TS209_GPIO_KEY_RESET,
.desc = "Reset Button",
.active_low = 1,
},
};
static struct gpio_keys_platform_data qnap_ts209_button_data = {
.buttons = qnap_ts209_buttons,
.nbuttons = ARRAY_SIZE(qnap_ts209_buttons),
};
static struct platform_device qnap_ts209_button_device = {
.name = "gpio-keys",
.id = -1,
.num_resources = 0,
.dev = {
.platform_data = &qnap_ts209_button_data,
},
};
/*****************************************************************************
* SATA
****************************************************************************/
static struct mv_sata_platform_data qnap_ts209_sata_data = {
.n_ports = 2,
};
/*****************************************************************************
* General Setup
****************************************************************************/
static unsigned int ts209_mpp_modes[] __initdata = {
MPP0_UNUSED,
MPP1_GPIO, /* USB copy button */
MPP2_GPIO, /* Load defaults button */
MPP3_GPIO, /* GPIO RTC */
MPP4_UNUSED,
MPP5_UNUSED,
MPP6_GPIO, /* PCI Int A */
MPP7_GPIO, /* PCI Int B */
MPP8_UNUSED,
MPP9_UNUSED,
MPP10_UNUSED,
MPP11_UNUSED,
MPP12_SATA_LED, /* SATA 0 presence */
MPP13_SATA_LED, /* SATA 1 presence */
MPP14_SATA_LED, /* SATA 0 active */
MPP15_SATA_LED, /* SATA 1 active */
MPP16_UART, /* UART1 RXD */
MPP17_UART, /* UART1 TXD */
MPP18_GPIO, /* SW_RST */
MPP19_UNUSED,
0,
};
static void __init qnap_ts209_init(void)
{
/*
* Setup basic Orion functions. Need to be called early.
*/
orion5x_init();
orion5x_mpp_conf(ts209_mpp_modes);
/*
* MPP[20] PCI clock 0
* MPP[21] PCI clock 1
* MPP[22] USB 0 over current
* MPP[23-25] Reserved
*/
/*
* Configure peripherals.
*/
orion5x_setup_dev_boot_win(QNAP_TS209_NOR_BOOT_BASE,
QNAP_TS209_NOR_BOOT_SIZE);
platform_device_register(&qnap_ts209_nor_flash);
orion5x_ehci0_init();
orion5x_ehci1_init();
qnap_tsx09_find_mac_addr(QNAP_TS209_NOR_BOOT_BASE +
qnap_ts209_partitions[5].offset,
qnap_ts209_partitions[5].size);
orion5x_eth_init(&qnap_tsx09_eth_data);
orion5x_i2c_init();
orion5x_sata_init(&qnap_ts209_sata_data);
orion5x_uart0_init();
orion5x_uart1_init();
orion5x_xor_init();
platform_device_register(&qnap_ts209_button_device);
/* Get RTC IRQ and register the chip */
if (gpio_request(TS209_RTC_GPIO, "rtc") == 0) {
if (gpio_direction_input(TS209_RTC_GPIO) == 0)
qnap_ts209_i2c_rtc.irq = gpio_to_irq(TS209_RTC_GPIO);
else
gpio_free(TS209_RTC_GPIO);
}
if (qnap_ts209_i2c_rtc.irq == 0)
pr_warning("qnap_ts209_init: failed to get RTC IRQ\n");
i2c_register_board_info(0, &qnap_ts209_i2c_rtc, 1);
/* register tsx09 specific power-off method */
pm_power_off = qnap_tsx09_power_off;
}
MACHINE_START(TS209, "QNAP TS-109/TS-209")
/* Maintainer: Byron Bradley <byron.bbradley@gmail.com> */
.atag_offset = 0x100,
.init_machine = qnap_ts209_init,
.map_io = orion5x_map_io,
.init_early = orion5x_init_early,
.init_irq = orion5x_init_irq,
.timer = &orion5x_timer,
.fixup = tag_fixup_mem32,
MACHINE_END