linux/arch/mn10300/kernel/gdb-stub.c
David Howells 2f2a2132ff Separate out the proc- and unit-specific header directories from the general
MN10300 arch headers and place them instead in the same directories as contain
the .c files for the processor and unit implementations.

This permits the symlinks include/asm/proc and include/asm/unit to be
dispensed with.  This does, however, require that #include <asm/proc/xxx.h> be
converted to #include <proc/xxx.h> and similarly for asm/unit -> unit.

Signed-off-by: David Howells <dhowells@redhat.com>
2009-04-10 14:33:48 +01:00

1912 lines
44 KiB
C

/* MN10300 GDB stub
*
* Originally written by Glenn Engel, Lake Stevens Instrument Division
*
* Contributed by HP Systems
*
* Modified for SPARC by Stu Grossman, Cygnus Support.
*
* Modified for Linux/MIPS (and MIPS in general) by Andreas Busse
* Send complaints, suggestions etc. to <andy@waldorf-gmbh.de>
*
* Copyright (C) 1995 Andreas Busse
*
* Copyright (C) 2007 Red Hat, Inc. All Rights Reserved.
* Modified for Linux/mn10300 by David Howells <dhowells@redhat.com>
*/
/*
* To enable debugger support, two things need to happen. One, a
* call to set_debug_traps() is necessary in order to allow any breakpoints
* or error conditions to be properly intercepted and reported to gdb.
* Two, a breakpoint needs to be generated to begin communication. This
* is most easily accomplished by a call to breakpoint(). Breakpoint()
* simulates a breakpoint by executing a BREAK instruction.
*
*
* The following gdb commands are supported:
*
* command function Return value
*
* g return the value of the CPU registers hex data or ENN
* G set the value of the CPU registers OK or ENN
*
* mAA..AA,LLLL Read LLLL bytes at address AA..AA hex data or ENN
* MAA..AA,LLLL: Write LLLL bytes at address AA.AA OK or ENN
*
* c Resume at current address SNN ( signal NN)
* cAA..AA Continue at address AA..AA SNN
*
* s Step one instruction SNN
* sAA..AA Step one instruction from AA..AA SNN
*
* k kill
*
* ? What was the last sigval ? SNN (signal NN)
*
* bBB..BB Set baud rate to BB..BB OK or BNN, then sets
* baud rate
*
* All commands and responses are sent with a packet which includes a
* checksum. A packet consists of
*
* $<packet info>#<checksum>.
*
* where
* <packet info> :: <characters representing the command or response>
* <checksum> :: < two hex digits computed as modulo 256 sum of <packetinfo>>
*
* When a packet is received, it is first acknowledged with either '+' or '-'.
* '+' indicates a successful transfer. '-' indicates a failed transfer.
*
* Example:
*
* Host: Reply:
* $m0,10#2a +$00010203040506070809101112131415#42
*
*
* ==============
* MORE EXAMPLES:
* ==============
*
* For reference -- the following are the steps that one
* company took (RidgeRun Inc) to get remote gdb debugging
* going. In this scenario the host machine was a PC and the
* target platform was a Galileo EVB64120A MIPS evaluation
* board.
*
* Step 1:
* First download gdb-5.0.tar.gz from the internet.
* and then build/install the package.
*
* Example:
* $ tar zxf gdb-5.0.tar.gz
* $ cd gdb-5.0
* $ ./configure --target=am33_2.0-linux-gnu
* $ make
* $ install
* am33_2.0-linux-gnu-gdb
*
* Step 2:
* Configure linux for remote debugging and build it.
*
* Example:
* $ cd ~/linux
* $ make menuconfig <go to "Kernel Hacking" and turn on remote debugging>
* $ make dep; make vmlinux
*
* Step 3:
* Download the kernel to the remote target and start
* the kernel running. It will promptly halt and wait
* for the host gdb session to connect. It does this
* since the "Kernel Hacking" option has defined
* CONFIG_REMOTE_DEBUG which in turn enables your calls
* to:
* set_debug_traps();
* breakpoint();
*
* Step 4:
* Start the gdb session on the host.
*
* Example:
* $ am33_2.0-linux-gnu-gdb vmlinux
* (gdb) set remotebaud 115200
* (gdb) target remote /dev/ttyS1
* ...at this point you are connected to
* the remote target and can use gdb
* in the normal fasion. Setting
* breakpoints, single stepping,
* printing variables, etc.
*
*/
#include <linux/string.h>
#include <linux/kernel.h>
#include <linux/signal.h>
#include <linux/sched.h>
#include <linux/mm.h>
#include <linux/console.h>
#include <linux/init.h>
#include <linux/bug.h>
#include <asm/pgtable.h>
#include <asm/system.h>
#include <asm/gdb-stub.h>
#include <asm/exceptions.h>
#include <asm/cacheflush.h>
#include <asm/serial-regs.h>
#include <asm/busctl-regs.h>
#include <unit/leds.h>
#include <unit/serial.h>
/* define to use F7F7 rather than FF which is subverted by JTAG debugger */
#undef GDBSTUB_USE_F7F7_AS_BREAKPOINT
/*
* BUFMAX defines the maximum number of characters in inbound/outbound buffers
* at least NUMREGBYTES*2 are needed for register packets
*/
#define BUFMAX 2048
static const char gdbstub_banner[] =
"Linux/MN10300 GDB Stub (c) RedHat 2007\n";
u8 gdbstub_rx_buffer[PAGE_SIZE] __attribute__((aligned(PAGE_SIZE)));
u32 gdbstub_rx_inp;
u32 gdbstub_rx_outp;
u8 gdbstub_busy;
u8 gdbstub_rx_overflow;
u8 gdbstub_rx_unget;
static u8 gdbstub_flush_caches;
static char input_buffer[BUFMAX];
static char output_buffer[BUFMAX];
static char trans_buffer[BUFMAX];
struct gdbstub_bkpt {
u8 *addr; /* address of breakpoint */
u8 len; /* size of breakpoint */
u8 origbytes[7]; /* original bytes */
};
static struct gdbstub_bkpt gdbstub_bkpts[256];
/*
* local prototypes
*/
static void getpacket(char *buffer);
static int putpacket(char *buffer);
static int computeSignal(enum exception_code excep);
static int hex(unsigned char ch);
static int hexToInt(char **ptr, int *intValue);
static unsigned char *mem2hex(const void *mem, char *buf, int count,
int may_fault);
static const char *hex2mem(const char *buf, void *_mem, int count,
int may_fault);
/*
* Convert ch from a hex digit to an int
*/
static int hex(unsigned char ch)
{
if (ch >= 'a' && ch <= 'f')
return ch - 'a' + 10;
if (ch >= '0' && ch <= '9')
return ch - '0';
if (ch >= 'A' && ch <= 'F')
return ch - 'A' + 10;
return -1;
}
#ifdef CONFIG_GDBSTUB_DEBUGGING
void debug_to_serial(const char *p, int n)
{
__debug_to_serial(p, n);
/* gdbstub_console_write(NULL, p, n); */
}
void gdbstub_printk(const char *fmt, ...)
{
va_list args;
int len;
/* Emit the output into the temporary buffer */
va_start(args, fmt);
len = vsnprintf(trans_buffer, sizeof(trans_buffer), fmt, args);
va_end(args);
debug_to_serial(trans_buffer, len);
}
#endif
static inline char *gdbstub_strcpy(char *dst, const char *src)
{
int loop = 0;
while ((dst[loop] = src[loop]))
loop++;
return dst;
}
/*
* scan for the sequence $<data>#<checksum>
*/
static void getpacket(char *buffer)
{
unsigned char checksum;
unsigned char xmitcsum;
unsigned char ch;
int count, i, ret, error;
for (;;) {
/*
* wait around for the start character,
* ignore all other characters
*/
do {
gdbstub_io_rx_char(&ch, 0);
} while (ch != '$');
checksum = 0;
xmitcsum = -1;
count = 0;
error = 0;
/*
* now, read until a # or end of buffer is found
*/
while (count < BUFMAX) {
ret = gdbstub_io_rx_char(&ch, 0);
if (ret < 0)
error = ret;
if (ch == '#')
break;
checksum += ch;
buffer[count] = ch;
count++;
}
if (error == -EIO) {
gdbstub_proto("### GDB Rx Error - Skipping packet"
" ###\n");
gdbstub_proto("### GDB Tx NAK\n");
gdbstub_io_tx_char('-');
continue;
}
if (count >= BUFMAX || error)
continue;
buffer[count] = 0;
/* read the checksum */
ret = gdbstub_io_rx_char(&ch, 0);
if (ret < 0)
error = ret;
xmitcsum = hex(ch) << 4;
ret = gdbstub_io_rx_char(&ch, 0);
if (ret < 0)
error = ret;
xmitcsum |= hex(ch);
if (error) {
if (error == -EIO)
gdbstub_io("### GDB Rx Error -"
" Skipping packet\n");
gdbstub_io("### GDB Tx NAK\n");
gdbstub_io_tx_char('-');
continue;
}
/* check the checksum */
if (checksum != xmitcsum) {
gdbstub_io("### GDB Tx NAK\n");
gdbstub_io_tx_char('-'); /* failed checksum */
continue;
}
gdbstub_proto("### GDB Rx '$%s#%02x' ###\n", buffer, checksum);
gdbstub_io("### GDB Tx ACK\n");
gdbstub_io_tx_char('+'); /* successful transfer */
/*
* if a sequence char is present,
* reply the sequence ID
*/
if (buffer[2] == ':') {
gdbstub_io_tx_char(buffer[0]);
gdbstub_io_tx_char(buffer[1]);
/*
* remove sequence chars from buffer
*/
count = 0;
while (buffer[count])
count++;
for (i = 3; i <= count; i++)
buffer[i - 3] = buffer[i];
}
break;
}
}
/*
* send the packet in buffer.
* - return 0 if successfully ACK'd
* - return 1 if abandoned due to new incoming packet
*/
static int putpacket(char *buffer)
{
unsigned char checksum;
unsigned char ch;
int count;
/*
* $<packet info>#<checksum>.
*/
gdbstub_proto("### GDB Tx $'%s'#?? ###\n", buffer);
do {
gdbstub_io_tx_char('$');
checksum = 0;
count = 0;
while ((ch = buffer[count]) != 0) {
gdbstub_io_tx_char(ch);
checksum += ch;
count += 1;
}
gdbstub_io_tx_char('#');
gdbstub_io_tx_char(hex_asc_hi(checksum));
gdbstub_io_tx_char(hex_asc_lo(checksum));
} while (gdbstub_io_rx_char(&ch, 0),
ch == '-' && (gdbstub_io("### GDB Rx NAK\n"), 0),
ch != '-' && ch != '+' &&
(gdbstub_io("### GDB Rx ??? %02x\n", ch), 0),
ch != '+' && ch != '$');
if (ch == '+') {
gdbstub_io("### GDB Rx ACK\n");
return 0;
}
gdbstub_io("### GDB Tx Abandoned\n");
gdbstub_rx_unget = ch;
return 1;
}
/*
* While we find nice hex chars, build an int.
* Return number of chars processed.
*/
static int hexToInt(char **ptr, int *intValue)
{
int numChars = 0;
int hexValue;
*intValue = 0;
while (**ptr) {
hexValue = hex(**ptr);
if (hexValue < 0)
break;
*intValue = (*intValue << 4) | hexValue;
numChars++;
(*ptr)++;
}
return (numChars);
}
/*
* We single-step by setting breakpoints. When an exception
* is handled, we need to restore the instructions hoisted
* when the breakpoints were set.
*
* This is where we save the original instructions.
*/
static struct gdb_bp_save {
u8 *addr;
u8 opcode[2];
} step_bp[2];
static const unsigned char gdbstub_insn_sizes[256] =
{
/* 1 2 3 4 5 6 7 8 9 a b c d e f */
1, 3, 3, 3, 1, 3, 3, 3, 1, 3, 3, 3, 1, 3, 3, 3, /* 0 */
1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, /* 1 */
2, 2, 2, 2, 3, 3, 3, 3, 2, 2, 2, 2, 3, 3, 3, 3, /* 2 */
3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 3, 1, 1, 1, 1, /* 3 */
1, 1, 2, 2, 1, 1, 2, 2, 1, 1, 2, 2, 1, 1, 2, 2, /* 4 */
1, 1, 1, 1, 1, 1, 1, 1, 2, 2, 2, 2, 2, 2, 2, 2, /* 5 */
1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, /* 6 */
1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, /* 7 */
2, 1, 1, 1, 1, 2, 1, 1, 1, 1, 2, 1, 1, 1, 1, 2, /* 8 */
2, 1, 1, 1, 1, 2, 1, 1, 1, 1, 2, 1, 1, 1, 1, 2, /* 9 */
2, 1, 1, 1, 1, 2, 1, 1, 1, 1, 2, 1, 1, 1, 1, 2, /* a */
2, 1, 1, 1, 1, 2, 1, 1, 1, 1, 2, 1, 1, 1, 1, 2, /* b */
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 1, 0, 0, 2, 2, /* c */
0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0, /* d */
1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, 1, /* e */
0, 2, 2, 2, 2, 2, 2, 4, 0, 3, 0, 4, 0, 6, 7, 1 /* f */
};
static int __gdbstub_mark_bp(u8 *addr, int ix)
{
if (addr < (u8 *) 0x70000000UL)
return 0;
/* 70000000-7fffffff: vmalloc area */
if (addr < (u8 *) 0x80000000UL)
goto okay;
if (addr < (u8 *) 0x8c000000UL)
return 0;
/* 8c000000-93ffffff: SRAM, SDRAM */
if (addr < (u8 *) 0x94000000UL)
goto okay;
return 0;
okay:
if (gdbstub_read_byte(addr + 0, &step_bp[ix].opcode[0]) < 0 ||
gdbstub_read_byte(addr + 1, &step_bp[ix].opcode[1]) < 0)
return 0;
step_bp[ix].addr = addr;
return 1;
}
static inline void __gdbstub_restore_bp(void)
{
#ifdef GDBSTUB_USE_F7F7_AS_BREAKPOINT
if (step_bp[0].addr) {
gdbstub_write_byte(step_bp[0].opcode[0], step_bp[0].addr + 0);
gdbstub_write_byte(step_bp[0].opcode[1], step_bp[0].addr + 1);
}
if (step_bp[1].addr) {
gdbstub_write_byte(step_bp[1].opcode[0], step_bp[1].addr + 0);
gdbstub_write_byte(step_bp[1].opcode[1], step_bp[1].addr + 1);
}
#else
if (step_bp[0].addr)
gdbstub_write_byte(step_bp[0].opcode[0], step_bp[0].addr + 0);
if (step_bp[1].addr)
gdbstub_write_byte(step_bp[1].opcode[0], step_bp[1].addr + 0);
#endif
gdbstub_flush_caches = 1;
step_bp[0].addr = NULL;
step_bp[0].opcode[0] = 0;
step_bp[0].opcode[1] = 0;
step_bp[1].addr = NULL;
step_bp[1].opcode[0] = 0;
step_bp[1].opcode[1] = 0;
}
/*
* emulate single stepping by means of breakpoint instructions
*/
static int gdbstub_single_step(struct pt_regs *regs)
{
unsigned size;
uint32_t x;
uint8_t cur, *pc, *sp;
step_bp[0].addr = NULL;
step_bp[0].opcode[0] = 0;
step_bp[0].opcode[1] = 0;
step_bp[1].addr = NULL;
step_bp[1].opcode[0] = 0;
step_bp[1].opcode[1] = 0;
x = 0;
pc = (u8 *) regs->pc;
sp = (u8 *) (regs + 1);
if (gdbstub_read_byte(pc, &cur) < 0)
return -EFAULT;
gdbstub_bkpt("Single Step from %p { %02x }\n", pc, cur);
gdbstub_flush_caches = 1;
size = gdbstub_insn_sizes[cur];
if (size > 0) {
if (!__gdbstub_mark_bp(pc + size, 0))
goto fault;
} else {
switch (cur) {
/* Bxx (d8,PC) */
case 0xc0 ... 0xca:
if (gdbstub_read_byte(pc + 1, (u8 *) &x) < 0)
goto fault;
if (!__gdbstub_mark_bp(pc + 2, 0))
goto fault;
if ((x < 0 || x > 2) &&
!__gdbstub_mark_bp(pc + (s8) x, 1))
goto fault;
break;
/* LXX (d8,PC) */
case 0xd0 ... 0xda:
if (!__gdbstub_mark_bp(pc + 1, 0))
goto fault;
if (regs->pc != regs->lar &&
!__gdbstub_mark_bp((u8 *) regs->lar, 1))
goto fault;
break;
/* SETLB - loads the next for bytes into the LIR
* register */
case 0xdb:
if (!__gdbstub_mark_bp(pc + 1, 0))
goto fault;
break;
/* JMP (d16,PC) or CALL (d16,PC) */
case 0xcc:
case 0xcd:
if (gdbstub_read_byte(pc + 1, ((u8 *) &x) + 0) < 0 ||
gdbstub_read_byte(pc + 2, ((u8 *) &x) + 1) < 0)
goto fault;
if (!__gdbstub_mark_bp(pc + (s16) x, 0))
goto fault;
break;
/* JMP (d32,PC) or CALL (d32,PC) */
case 0xdc:
case 0xdd:
if (gdbstub_read_byte(pc + 1, ((u8 *) &x) + 0) < 0 ||
gdbstub_read_byte(pc + 2, ((u8 *) &x) + 1) < 0 ||
gdbstub_read_byte(pc + 3, ((u8 *) &x) + 2) < 0 ||
gdbstub_read_byte(pc + 4, ((u8 *) &x) + 3) < 0)
goto fault;
if (!__gdbstub_mark_bp(pc + (s32) x, 0))
goto fault;
break;
/* RETF */
case 0xde:
if (!__gdbstub_mark_bp((u8 *) regs->mdr, 0))
goto fault;
break;
/* RET */
case 0xdf:
if (gdbstub_read_byte(pc + 2, (u8 *) &x) < 0)
goto fault;
sp += (s8)x;
if (gdbstub_read_byte(sp + 0, ((u8 *) &x) + 0) < 0 ||
gdbstub_read_byte(sp + 1, ((u8 *) &x) + 1) < 0 ||
gdbstub_read_byte(sp + 2, ((u8 *) &x) + 2) < 0 ||
gdbstub_read_byte(sp + 3, ((u8 *) &x) + 3) < 0)
goto fault;
if (!__gdbstub_mark_bp((u8 *) x, 0))
goto fault;
break;
case 0xf0:
if (gdbstub_read_byte(pc + 1, &cur) < 0)
goto fault;
if (cur >= 0xf0 && cur <= 0xf7) {
/* JMP (An) / CALLS (An) */
switch (cur & 3) {
case 0: x = regs->a0; break;
case 1: x = regs->a1; break;
case 2: x = regs->a2; break;
case 3: x = regs->a3; break;
}
if (!__gdbstub_mark_bp((u8 *) x, 0))
goto fault;
} else if (cur == 0xfc) {
/* RETS */
if (gdbstub_read_byte(
sp + 0, ((u8 *) &x) + 0) < 0 ||
gdbstub_read_byte(
sp + 1, ((u8 *) &x) + 1) < 0 ||
gdbstub_read_byte(
sp + 2, ((u8 *) &x) + 2) < 0 ||
gdbstub_read_byte(
sp + 3, ((u8 *) &x) + 3) < 0)
goto fault;
if (!__gdbstub_mark_bp((u8 *) x, 0))
goto fault;
} else if (cur == 0xfd) {
/* RTI */
if (gdbstub_read_byte(
sp + 4, ((u8 *) &x) + 0) < 0 ||
gdbstub_read_byte(
sp + 5, ((u8 *) &x) + 1) < 0 ||
gdbstub_read_byte(
sp + 6, ((u8 *) &x) + 2) < 0 ||
gdbstub_read_byte(
sp + 7, ((u8 *) &x) + 3) < 0)
goto fault;
if (!__gdbstub_mark_bp((u8 *) x, 0))
goto fault;
} else {
if (!__gdbstub_mark_bp(pc + 2, 0))
goto fault;
}
break;
/* potential 3-byte conditional branches */
case 0xf8:
if (gdbstub_read_byte(pc + 1, &cur) < 0)
goto fault;
if (!__gdbstub_mark_bp(pc + 3, 0))
goto fault;
if (cur >= 0xe8 && cur <= 0xeb) {
if (gdbstub_read_byte(
pc + 2, ((u8 *) &x) + 0) < 0)
goto fault;
if ((x < 0 || x > 3) &&
!__gdbstub_mark_bp(pc + (s8) x, 1))
goto fault;
}
break;
case 0xfa:
if (gdbstub_read_byte(pc + 1, &cur) < 0)
goto fault;
if (cur == 0xff) {
/* CALLS (d16,PC) */
if (gdbstub_read_byte(
pc + 2, ((u8 *) &x) + 0) < 0 ||
gdbstub_read_byte(
pc + 3, ((u8 *) &x) + 1) < 0)
goto fault;
if (!__gdbstub_mark_bp(pc + (s16) x, 0))
goto fault;
} else {
if (!__gdbstub_mark_bp(pc + 4, 0))
goto fault;
}
break;
case 0xfc:
if (gdbstub_read_byte(pc + 1, &cur) < 0)
goto fault;
if (cur == 0xff) {
/* CALLS (d32,PC) */
if (gdbstub_read_byte(
pc + 2, ((u8 *) &x) + 0) < 0 ||
gdbstub_read_byte(
pc + 3, ((u8 *) &x) + 1) < 0 ||
gdbstub_read_byte(
pc + 4, ((u8 *) &x) + 2) < 0 ||
gdbstub_read_byte(
pc + 5, ((u8 *) &x) + 3) < 0)
goto fault;
if (!__gdbstub_mark_bp(
pc + (s32) x, 0))
goto fault;
} else {
if (!__gdbstub_mark_bp(
pc + 6, 0))
goto fault;
}
break;
}
}
gdbstub_bkpt("Step: %02x at %p; %02x at %p\n",
step_bp[0].opcode[0], step_bp[0].addr,
step_bp[1].opcode[0], step_bp[1].addr);
if (step_bp[0].addr) {
#ifdef GDBSTUB_USE_F7F7_AS_BREAKPOINT
if (gdbstub_write_byte(0xF7, step_bp[0].addr + 0) < 0 ||
gdbstub_write_byte(0xF7, step_bp[0].addr + 1) < 0)
goto fault;
#else
if (gdbstub_write_byte(0xFF, step_bp[0].addr + 0) < 0)
goto fault;
#endif
}
if (step_bp[1].addr) {
#ifdef GDBSTUB_USE_F7F7_AS_BREAKPOINT
if (gdbstub_write_byte(0xF7, step_bp[1].addr + 0) < 0 ||
gdbstub_write_byte(0xF7, step_bp[1].addr + 1) < 0)
goto fault;
#else
if (gdbstub_write_byte(0xFF, step_bp[1].addr + 0) < 0)
goto fault;
#endif
}
return 0;
fault:
/* uh-oh - silly address alert, try and restore things */
__gdbstub_restore_bp();
return -EFAULT;
}
#ifdef CONFIG_GDBSTUB_CONSOLE
void gdbstub_console_write(struct console *con, const char *p, unsigned n)
{
static const char gdbstub_cr[] = { 0x0d };
char outbuf[26];
int qty;
u8 busy;
busy = gdbstub_busy;
gdbstub_busy = 1;
outbuf[0] = 'O';
while (n > 0) {
qty = 1;
while (n > 0 && qty < 20) {
mem2hex(p, outbuf + qty, 2, 0);
qty += 2;
if (*p == 0x0a) {
mem2hex(gdbstub_cr, outbuf + qty, 2, 0);
qty += 2;
}
p++;
n--;
}
outbuf[qty] = 0;
putpacket(outbuf);
}
gdbstub_busy = busy;
}
static kdev_t gdbstub_console_dev(struct console *con)
{
return MKDEV(1, 3); /* /dev/null */
}
static struct console gdbstub_console = {
.name = "gdb",
.write = gdbstub_console_write,
.device = gdbstub_console_dev,
.flags = CON_PRINTBUFFER,
.index = -1,
};
#endif
/*
* Convert the memory pointed to by mem into hex, placing result in buf.
* - if successful, return a pointer to the last char put in buf (NUL)
* - in case of mem fault, return NULL
* may_fault is non-zero if we are reading from arbitrary memory, but is
* currently not used.
*/
static
unsigned char *mem2hex(const void *_mem, char *buf, int count, int may_fault)
{
const u8 *mem = _mem;
u8 ch[4];
if ((u32) mem & 1 && count >= 1) {
if (gdbstub_read_byte(mem, ch) != 0)
return 0;
buf = pack_hex_byte(buf, ch[0]);
mem++;
count--;
}
if ((u32) mem & 3 && count >= 2) {
if (gdbstub_read_word(mem, ch) != 0)
return 0;
buf = pack_hex_byte(buf, ch[0]);
buf = pack_hex_byte(buf, ch[1]);
mem += 2;
count -= 2;
}
while (count >= 4) {
if (gdbstub_read_dword(mem, ch) != 0)
return 0;
buf = pack_hex_byte(buf, ch[0]);
buf = pack_hex_byte(buf, ch[1]);
buf = pack_hex_byte(buf, ch[2]);
buf = pack_hex_byte(buf, ch[3]);
mem += 4;
count -= 4;
}
if (count >= 2) {
if (gdbstub_read_word(mem, ch) != 0)
return 0;
buf = pack_hex_byte(buf, ch[0]);
buf = pack_hex_byte(buf, ch[1]);
mem += 2;
count -= 2;
}
if (count >= 1) {
if (gdbstub_read_byte(mem, ch) != 0)
return 0;
buf = pack_hex_byte(buf, ch[0]);
}
*buf = 0;
return buf;
}
/*
* convert the hex array pointed to by buf into binary to be placed in mem
* return a pointer to the character AFTER the last byte written
* may_fault is non-zero if we are reading from arbitrary memory, but is
* currently not used.
*/
static
const char *hex2mem(const char *buf, void *_mem, int count, int may_fault)
{
u8 *mem = _mem;
union {
u32 val;
u8 b[4];
} ch;
if ((u32) mem & 1 && count >= 1) {
ch.b[0] = hex(*buf++) << 4;
ch.b[0] |= hex(*buf++);
if (gdbstub_write_byte(ch.val, mem) != 0)
return 0;
mem++;
count--;
}
if ((u32) mem & 3 && count >= 2) {
ch.b[0] = hex(*buf++) << 4;
ch.b[0] |= hex(*buf++);
ch.b[1] = hex(*buf++) << 4;
ch.b[1] |= hex(*buf++);
if (gdbstub_write_word(ch.val, mem) != 0)
return 0;
mem += 2;
count -= 2;
}
while (count >= 4) {
ch.b[0] = hex(*buf++) << 4;
ch.b[0] |= hex(*buf++);
ch.b[1] = hex(*buf++) << 4;
ch.b[1] |= hex(*buf++);
ch.b[2] = hex(*buf++) << 4;
ch.b[2] |= hex(*buf++);
ch.b[3] = hex(*buf++) << 4;
ch.b[3] |= hex(*buf++);
if (gdbstub_write_dword(ch.val, mem) != 0)
return 0;
mem += 4;
count -= 4;
}
if (count >= 2) {
ch.b[0] = hex(*buf++) << 4;
ch.b[0] |= hex(*buf++);
ch.b[1] = hex(*buf++) << 4;
ch.b[1] |= hex(*buf++);
if (gdbstub_write_word(ch.val, mem) != 0)
return 0;
mem += 2;
count -= 2;
}
if (count >= 1) {
ch.b[0] = hex(*buf++) << 4;
ch.b[0] |= hex(*buf++);
if (gdbstub_write_byte(ch.val, mem) != 0)
return 0;
}
return buf;
}
/*
* This table contains the mapping between MN10300 exception codes, and
* signals, which are primarily what GDB understands. It also indicates
* which hardware traps we need to commandeer when initializing the stub.
*/
static const struct excep_to_sig_map {
enum exception_code excep; /* MN10300 exception code */
unsigned char signo; /* Signal that we map this into */
} excep_to_sig_map[] = {
{ EXCEP_ITLBMISS, SIGSEGV },
{ EXCEP_DTLBMISS, SIGSEGV },
{ EXCEP_TRAP, SIGTRAP },
{ EXCEP_ISTEP, SIGTRAP },
{ EXCEP_IBREAK, SIGTRAP },
{ EXCEP_OBREAK, SIGTRAP },
{ EXCEP_UNIMPINS, SIGILL },
{ EXCEP_UNIMPEXINS, SIGILL },
{ EXCEP_MEMERR, SIGSEGV },
{ EXCEP_MISALIGN, SIGSEGV },
{ EXCEP_BUSERROR, SIGBUS },
{ EXCEP_ILLINSACC, SIGSEGV },
{ EXCEP_ILLDATACC, SIGSEGV },
{ EXCEP_IOINSACC, SIGSEGV },
{ EXCEP_PRIVINSACC, SIGSEGV },
{ EXCEP_PRIVDATACC, SIGSEGV },
{ EXCEP_FPU_DISABLED, SIGFPE },
{ EXCEP_FPU_UNIMPINS, SIGFPE },
{ EXCEP_FPU_OPERATION, SIGFPE },
{ EXCEP_WDT, SIGALRM },
{ EXCEP_NMI, SIGQUIT },
{ EXCEP_IRQ_LEVEL0, SIGINT },
{ EXCEP_IRQ_LEVEL1, SIGINT },
{ EXCEP_IRQ_LEVEL2, SIGINT },
{ EXCEP_IRQ_LEVEL3, SIGINT },
{ EXCEP_IRQ_LEVEL4, SIGINT },
{ EXCEP_IRQ_LEVEL5, SIGINT },
{ EXCEP_IRQ_LEVEL6, SIGINT },
{ 0, 0}
};
/*
* convert the MN10300 exception code into a UNIX signal number
*/
static int computeSignal(enum exception_code excep)
{
const struct excep_to_sig_map *map;
for (map = excep_to_sig_map; map->signo; map++)
if (map->excep == excep)
return map->signo;
return SIGHUP; /* default for things we don't know about */
}
static u32 gdbstub_fpcr, gdbstub_fpufs_array[32];
/*
*
*/
static void gdbstub_store_fpu(void)
{
#ifdef CONFIG_FPU
asm volatile(
"or %2,epsw\n"
#ifdef CONFIG_MN10300_PROC_MN103E010
"nop\n"
"nop\n"
#endif
"mov %1, a1\n"
"fmov fs0, (a1+)\n"
"fmov fs1, (a1+)\n"
"fmov fs2, (a1+)\n"
"fmov fs3, (a1+)\n"
"fmov fs4, (a1+)\n"
"fmov fs5, (a1+)\n"
"fmov fs6, (a1+)\n"
"fmov fs7, (a1+)\n"
"fmov fs8, (a1+)\n"
"fmov fs9, (a1+)\n"
"fmov fs10, (a1+)\n"
"fmov fs11, (a1+)\n"
"fmov fs12, (a1+)\n"
"fmov fs13, (a1+)\n"
"fmov fs14, (a1+)\n"
"fmov fs15, (a1+)\n"
"fmov fs16, (a1+)\n"
"fmov fs17, (a1+)\n"
"fmov fs18, (a1+)\n"
"fmov fs19, (a1+)\n"
"fmov fs20, (a1+)\n"
"fmov fs21, (a1+)\n"
"fmov fs22, (a1+)\n"
"fmov fs23, (a1+)\n"
"fmov fs24, (a1+)\n"
"fmov fs25, (a1+)\n"
"fmov fs26, (a1+)\n"
"fmov fs27, (a1+)\n"
"fmov fs28, (a1+)\n"
"fmov fs29, (a1+)\n"
"fmov fs30, (a1+)\n"
"fmov fs31, (a1+)\n"
"fmov fpcr, %0\n"
: "=d"(gdbstub_fpcr)
: "g" (&gdbstub_fpufs_array), "i"(EPSW_FE)
: "a1"
);
#endif
}
/*
*
*/
static void gdbstub_load_fpu(void)
{
#ifdef CONFIG_FPU
asm volatile(
"or %1,epsw\n"
#ifdef CONFIG_MN10300_PROC_MN103E010
"nop\n"
"nop\n"
#endif
"mov %0, a1\n"
"fmov (a1+), fs0\n"
"fmov (a1+), fs1\n"
"fmov (a1+), fs2\n"
"fmov (a1+), fs3\n"
"fmov (a1+), fs4\n"
"fmov (a1+), fs5\n"
"fmov (a1+), fs6\n"
"fmov (a1+), fs7\n"
"fmov (a1+), fs8\n"
"fmov (a1+), fs9\n"
"fmov (a1+), fs10\n"
"fmov (a1+), fs11\n"
"fmov (a1+), fs12\n"
"fmov (a1+), fs13\n"
"fmov (a1+), fs14\n"
"fmov (a1+), fs15\n"
"fmov (a1+), fs16\n"
"fmov (a1+), fs17\n"
"fmov (a1+), fs18\n"
"fmov (a1+), fs19\n"
"fmov (a1+), fs20\n"
"fmov (a1+), fs21\n"
"fmov (a1+), fs22\n"
"fmov (a1+), fs23\n"
"fmov (a1+), fs24\n"
"fmov (a1+), fs25\n"
"fmov (a1+), fs26\n"
"fmov (a1+), fs27\n"
"fmov (a1+), fs28\n"
"fmov (a1+), fs29\n"
"fmov (a1+), fs30\n"
"fmov (a1+), fs31\n"
"fmov %2, fpcr\n"
:
: "g" (&gdbstub_fpufs_array), "i"(EPSW_FE), "d"(gdbstub_fpcr)
: "a1"
);
#endif
}
/*
* set a software breakpoint
*/
int gdbstub_set_breakpoint(u8 *addr, int len)
{
int bkpt, loop, xloop;
#ifdef GDBSTUB_USE_F7F7_AS_BREAKPOINT
len = (len + 1) & ~1;
#endif
gdbstub_bkpt("setbkpt(%p,%d)\n", addr, len);
for (bkpt = 255; bkpt >= 0; bkpt--)
if (!gdbstub_bkpts[bkpt].addr)
break;
if (bkpt < 0)
return -ENOSPC;
for (loop = 0; loop < len; loop++)
if (gdbstub_read_byte(&addr[loop],
&gdbstub_bkpts[bkpt].origbytes[loop]
) < 0)
return -EFAULT;
gdbstub_flush_caches = 1;
#ifdef GDBSTUB_USE_F7F7_AS_BREAKPOINT
for (loop = 0; loop < len; loop++)
if (gdbstub_write_byte(0xF7, &addr[loop]) < 0)
goto restore;
#else
for (loop = 0; loop < len; loop++)
if (gdbstub_write_byte(0xFF, &addr[loop]) < 0)
goto restore;
#endif
gdbstub_bkpts[bkpt].addr = addr;
gdbstub_bkpts[bkpt].len = len;
gdbstub_bkpt("Set BKPT[%02x]: %p-%p {%02x%02x%02x%02x%02x%02x%02x}\n",
bkpt,
gdbstub_bkpts[bkpt].addr,
gdbstub_bkpts[bkpt].addr + gdbstub_bkpts[bkpt].len - 1,
gdbstub_bkpts[bkpt].origbytes[0],
gdbstub_bkpts[bkpt].origbytes[1],
gdbstub_bkpts[bkpt].origbytes[2],
gdbstub_bkpts[bkpt].origbytes[3],
gdbstub_bkpts[bkpt].origbytes[4],
gdbstub_bkpts[bkpt].origbytes[5],
gdbstub_bkpts[bkpt].origbytes[6]
);
return 0;
restore:
for (xloop = 0; xloop < loop; xloop++)
gdbstub_write_byte(gdbstub_bkpts[bkpt].origbytes[xloop],
addr + xloop);
return -EFAULT;
}
/*
* clear a software breakpoint
*/
int gdbstub_clear_breakpoint(u8 *addr, int len)
{
int bkpt, loop;
#ifdef GDBSTUB_USE_F7F7_AS_BREAKPOINT
len = (len + 1) & ~1;
#endif
gdbstub_bkpt("clearbkpt(%p,%d)\n", addr, len);
for (bkpt = 255; bkpt >= 0; bkpt--)
if (gdbstub_bkpts[bkpt].addr == addr &&
gdbstub_bkpts[bkpt].len == len)
break;
if (bkpt < 0)
return -ENOENT;
gdbstub_bkpts[bkpt].addr = NULL;
gdbstub_flush_caches = 1;
for (loop = 0; loop < len; loop++)
if (gdbstub_write_byte(gdbstub_bkpts[bkpt].origbytes[loop],
addr + loop) < 0)
return -EFAULT;
return 0;
}
/*
* This function does all command processing for interfacing to gdb
* - returns 1 if the exception should be skipped, 0 otherwise.
*/
static int gdbstub(struct pt_regs *regs, enum exception_code excep)
{
unsigned long *stack;
unsigned long epsw, mdr;
uint32_t zero, ssp;
uint8_t broke;
char *ptr;
int sigval;
int addr;
int length;
int loop;
if (excep == EXCEP_FPU_DISABLED)
return 0;
gdbstub_flush_caches = 0;
mn10300_set_gdbleds(1);
asm volatile("mov mdr,%0" : "=d"(mdr));
asm volatile("mov epsw,%0" : "=d"(epsw));
asm volatile("mov %0,epsw"
:: "d"((epsw & ~EPSW_IM) | EPSW_IE | EPSW_IM_1));
gdbstub_store_fpu();
#ifdef CONFIG_GDBSTUB_IMMEDIATE
/* skip the initial pause loop */
if (regs->pc == (unsigned long) __gdbstub_pause)
regs->pc = (unsigned long) start_kernel;
#endif
/* if we were single stepping, restore the opcodes hoisted for the
* breakpoint[s] */
broke = 0;
if ((step_bp[0].addr && step_bp[0].addr == (u8 *) regs->pc) ||
(step_bp[1].addr && step_bp[1].addr == (u8 *) regs->pc))
broke = 1;
__gdbstub_restore_bp();
if (gdbstub_rx_unget) {
sigval = SIGINT;
if (gdbstub_rx_unget != 3)
goto packet_waiting;
gdbstub_rx_unget = 0;
}
stack = (unsigned long *) regs->sp;
sigval = broke ? SIGTRAP : computeSignal(excep);
/* send information about a BUG() */
if (!user_mode(regs) && excep == EXCEP_SYSCALL15) {
const struct bug_entry *bug;
bug = find_bug(regs->pc);
if (bug)
goto found_bug;
length = snprintf(trans_buffer, sizeof(trans_buffer),
"BUG() at address %lx\n", regs->pc);
goto send_bug_pkt;
found_bug:
length = snprintf(trans_buffer, sizeof(trans_buffer),
"BUG() at address %lx (%s:%d)\n",
regs->pc, bug->file, bug->line);
send_bug_pkt:
ptr = output_buffer;
*ptr++ = 'O';
ptr = mem2hex(trans_buffer, ptr, length, 0);
*ptr = 0;
putpacket(output_buffer);
regs->pc -= 2;
sigval = SIGABRT;
} else if (regs->pc == (unsigned long) __gdbstub_bug_trap) {
regs->pc = regs->mdr;
sigval = SIGABRT;
}
/*
* send a message to the debugger's user saying what happened if it may
* not be clear cut (we can't map exceptions onto signals properly)
*/
if (sigval != SIGINT && sigval != SIGTRAP && sigval != SIGILL) {
static const char title[] = "Excep ", tbcberr[] = "BCBERR ";
static const char crlf[] = "\r\n";
char hx;
u32 bcberr = BCBERR;
ptr = output_buffer;
*ptr++ = 'O';
ptr = mem2hex(title, ptr, sizeof(title) - 1, 0);
hx = hex_asc_hi(excep >> 8);
ptr = pack_hex_byte(ptr, hx);
hx = hex_asc_lo(excep >> 8);
ptr = pack_hex_byte(ptr, hx);
hx = hex_asc_hi(excep);
ptr = pack_hex_byte(ptr, hx);
hx = hex_asc_lo(excep);
ptr = pack_hex_byte(ptr, hx);
ptr = mem2hex(crlf, ptr, sizeof(crlf) - 1, 0);
*ptr = 0;
putpacket(output_buffer); /* send it off... */
/* BCBERR */
ptr = output_buffer;
*ptr++ = 'O';
ptr = mem2hex(tbcberr, ptr, sizeof(tbcberr) - 1, 0);
hx = hex_asc_hi(bcberr >> 24);
ptr = pack_hex_byte(ptr, hx);
hx = hex_asc_lo(bcberr >> 24);
ptr = pack_hex_byte(ptr, hx);
hx = hex_asc_hi(bcberr >> 16);
ptr = pack_hex_byte(ptr, hx);
hx = hex_asc_lo(bcberr >> 16);
ptr = pack_hex_byte(ptr, hx);
hx = hex_asc_hi(bcberr >> 8);
ptr = pack_hex_byte(ptr, hx);
hx = hex_asc_lo(bcberr >> 8);
ptr = pack_hex_byte(ptr, hx);
hx = hex_asc_hi(bcberr);
ptr = pack_hex_byte(ptr, hx);
hx = hex_asc_lo(bcberr);
ptr = pack_hex_byte(ptr, hx);
ptr = mem2hex(crlf, ptr, sizeof(crlf) - 1, 0);
*ptr = 0;
putpacket(output_buffer); /* send it off... */
}
/*
* tell the debugger that an exception has occurred
*/
ptr = output_buffer;
/*
* Send trap type (converted to signal)
*/
*ptr++ = 'T';
ptr = pack_hex_byte(ptr, sigval);
/*
* Send Error PC
*/
ptr = pack_hex_byte(ptr, GDB_REGID_PC);
*ptr++ = ':';
ptr = mem2hex(&regs->pc, ptr, 4, 0);
*ptr++ = ';';
/*
* Send frame pointer
*/
ptr = pack_hex_byte(ptr, GDB_REGID_FP);
*ptr++ = ':';
ptr = mem2hex(&regs->a3, ptr, 4, 0);
*ptr++ = ';';
/*
* Send stack pointer
*/
ssp = (unsigned long) (regs + 1);
ptr = pack_hex_byte(ptr, GDB_REGID_SP);
*ptr++ = ':';
ptr = mem2hex(&ssp, ptr, 4, 0);
*ptr++ = ';';
*ptr++ = 0;
putpacket(output_buffer); /* send it off... */
packet_waiting:
/*
* Wait for input from remote GDB
*/
while (1) {
output_buffer[0] = 0;
getpacket(input_buffer);
switch (input_buffer[0]) {
/* request repeat of last signal number */
case '?':
output_buffer[0] = 'S';
output_buffer[1] = hex_asc_hi(sigval);
output_buffer[2] = hex_asc_lo(sigval);
output_buffer[3] = 0;
break;
case 'd':
/* toggle debug flag */
break;
/*
* Return the value of the CPU registers
*/
case 'g':
zero = 0;
ssp = (u32) (regs + 1);
ptr = output_buffer;
ptr = mem2hex(&regs->d0, ptr, 4, 0);
ptr = mem2hex(&regs->d1, ptr, 4, 0);
ptr = mem2hex(&regs->d2, ptr, 4, 0);
ptr = mem2hex(&regs->d3, ptr, 4, 0);
ptr = mem2hex(&regs->a0, ptr, 4, 0);
ptr = mem2hex(&regs->a1, ptr, 4, 0);
ptr = mem2hex(&regs->a2, ptr, 4, 0);
ptr = mem2hex(&regs->a3, ptr, 4, 0);
ptr = mem2hex(&ssp, ptr, 4, 0); /* 8 */
ptr = mem2hex(&regs->pc, ptr, 4, 0);
ptr = mem2hex(&regs->mdr, ptr, 4, 0);
ptr = mem2hex(&regs->epsw, ptr, 4, 0);
ptr = mem2hex(&regs->lir, ptr, 4, 0);
ptr = mem2hex(&regs->lar, ptr, 4, 0);
ptr = mem2hex(&regs->mdrq, ptr, 4, 0);
ptr = mem2hex(&regs->e0, ptr, 4, 0); /* 15 */
ptr = mem2hex(&regs->e1, ptr, 4, 0);
ptr = mem2hex(&regs->e2, ptr, 4, 0);
ptr = mem2hex(&regs->e3, ptr, 4, 0);
ptr = mem2hex(&regs->e4, ptr, 4, 0);
ptr = mem2hex(&regs->e5, ptr, 4, 0);
ptr = mem2hex(&regs->e6, ptr, 4, 0);
ptr = mem2hex(&regs->e7, ptr, 4, 0);
ptr = mem2hex(&ssp, ptr, 4, 0);
ptr = mem2hex(&regs, ptr, 4, 0);
ptr = mem2hex(&regs->sp, ptr, 4, 0);
ptr = mem2hex(&regs->mcrh, ptr, 4, 0); /* 26 */
ptr = mem2hex(&regs->mcrl, ptr, 4, 0);
ptr = mem2hex(&regs->mcvf, ptr, 4, 0);
ptr = mem2hex(&gdbstub_fpcr, ptr, 4, 0); /* 29 - FPCR */
ptr = mem2hex(&zero, ptr, 4, 0);
ptr = mem2hex(&zero, ptr, 4, 0);
for (loop = 0; loop < 32; loop++)
ptr = mem2hex(&gdbstub_fpufs_array[loop],
ptr, 4, 0); /* 32 - FS0-31 */
break;
/*
* set the value of the CPU registers - return OK
*/
case 'G':
{
const char *ptr;
ptr = &input_buffer[1];
ptr = hex2mem(ptr, &regs->d0, 4, 0);
ptr = hex2mem(ptr, &regs->d1, 4, 0);
ptr = hex2mem(ptr, &regs->d2, 4, 0);
ptr = hex2mem(ptr, &regs->d3, 4, 0);
ptr = hex2mem(ptr, &regs->a0, 4, 0);
ptr = hex2mem(ptr, &regs->a1, 4, 0);
ptr = hex2mem(ptr, &regs->a2, 4, 0);
ptr = hex2mem(ptr, &regs->a3, 4, 0);
ptr = hex2mem(ptr, &ssp, 4, 0); /* 8 */
ptr = hex2mem(ptr, &regs->pc, 4, 0);
ptr = hex2mem(ptr, &regs->mdr, 4, 0);
ptr = hex2mem(ptr, &regs->epsw, 4, 0);
ptr = hex2mem(ptr, &regs->lir, 4, 0);
ptr = hex2mem(ptr, &regs->lar, 4, 0);
ptr = hex2mem(ptr, &regs->mdrq, 4, 0);
ptr = hex2mem(ptr, &regs->e0, 4, 0); /* 15 */
ptr = hex2mem(ptr, &regs->e1, 4, 0);
ptr = hex2mem(ptr, &regs->e2, 4, 0);
ptr = hex2mem(ptr, &regs->e3, 4, 0);
ptr = hex2mem(ptr, &regs->e4, 4, 0);
ptr = hex2mem(ptr, &regs->e5, 4, 0);
ptr = hex2mem(ptr, &regs->e6, 4, 0);
ptr = hex2mem(ptr, &regs->e7, 4, 0);
ptr = hex2mem(ptr, &ssp, 4, 0);
ptr = hex2mem(ptr, &zero, 4, 0);
ptr = hex2mem(ptr, &regs->sp, 4, 0);
ptr = hex2mem(ptr, &regs->mcrh, 4, 0); /* 26 */
ptr = hex2mem(ptr, &regs->mcrl, 4, 0);
ptr = hex2mem(ptr, &regs->mcvf, 4, 0);
ptr = hex2mem(ptr, &zero, 4, 0); /* 29 - FPCR */
ptr = hex2mem(ptr, &zero, 4, 0);
ptr = hex2mem(ptr, &zero, 4, 0);
for (loop = 0; loop < 32; loop++) /* 32 - FS0-31 */
ptr = hex2mem(ptr, &zero, 4, 0);
#if 0
/*
* See if the stack pointer has moved. If so, then copy
* the saved locals and ins to the new location.
*/
unsigned long *newsp = (unsigned long *) registers[SP];
if (sp != newsp)
sp = memcpy(newsp, sp, 16 * 4);
#endif
gdbstub_strcpy(output_buffer, "OK");
}
break;
/*
* mAA..AA,LLLL Read LLLL bytes at address AA..AA
*/
case 'm':
ptr = &input_buffer[1];
if (hexToInt(&ptr, &addr) &&
*ptr++ == ',' &&
hexToInt(&ptr, &length)
) {
if (mem2hex((char *) addr, output_buffer,
length, 1))
break;
gdbstub_strcpy(output_buffer, "E03");
} else {
gdbstub_strcpy(output_buffer, "E01");
}
break;
/*
* MAA..AA,LLLL: Write LLLL bytes at address AA.AA
* return OK
*/
case 'M':
ptr = &input_buffer[1];
if (hexToInt(&ptr, &addr) &&
*ptr++ == ',' &&
hexToInt(&ptr, &length) &&
*ptr++ == ':'
) {
if (hex2mem(ptr, (char *) addr, length, 1))
gdbstub_strcpy(output_buffer, "OK");
else
gdbstub_strcpy(output_buffer, "E03");
gdbstub_flush_caches = 1;
} else {
gdbstub_strcpy(output_buffer, "E02");
}
break;
/*
* cAA..AA Continue at address AA..AA(optional)
*/
case 'c':
/* try to read optional parameter, pc unchanged if no
* parm */
ptr = &input_buffer[1];
if (hexToInt(&ptr, &addr))
regs->pc = addr;
goto done;
/*
* kill the program
*/
case 'k' :
goto done; /* just continue */
/*
* Reset the whole machine (FIXME: system dependent)
*/
case 'r':
break;
/*
* Step to next instruction
*/
case 's':
/*
* using the T flag doesn't seem to perform single
* stepping (it seems to wind up being caught by the
* JTAG unit), so we have to use breakpoints and
* continue instead.
*/
if (gdbstub_single_step(regs) < 0)
/* ignore any fault error for now */
gdbstub_printk("unable to set single-step"
" bp\n");
goto done;
/*
* Set baud rate (bBB)
*/
case 'b':
do {
int baudrate;
ptr = &input_buffer[1];
if (!hexToInt(&ptr, &baudrate)) {
gdbstub_strcpy(output_buffer, "B01");
break;
}
if (baudrate) {
/* ACK before changing speed */
putpacket("OK");
gdbstub_io_set_baud(baudrate);
}
} while (0);
break;
/*
* Set breakpoint
*/
case 'Z':
ptr = &input_buffer[1];
if (!hexToInt(&ptr, &loop) || *ptr++ != ',' ||
!hexToInt(&ptr, &addr) || *ptr++ != ',' ||
!hexToInt(&ptr, &length)
) {
gdbstub_strcpy(output_buffer, "E01");
break;
}
/* only support software breakpoints */
gdbstub_strcpy(output_buffer, "E03");
if (loop != 0 ||
length < 1 ||
length > 7 ||
(unsigned long) addr < 4096)
break;
if (gdbstub_set_breakpoint((u8 *) addr, length) < 0)
break;
gdbstub_strcpy(output_buffer, "OK");
break;
/*
* Clear breakpoint
*/
case 'z':
ptr = &input_buffer[1];
if (!hexToInt(&ptr, &loop) || *ptr++ != ',' ||
!hexToInt(&ptr, &addr) || *ptr++ != ',' ||
!hexToInt(&ptr, &length)
) {
gdbstub_strcpy(output_buffer, "E01");
break;
}
/* only support software breakpoints */
gdbstub_strcpy(output_buffer, "E03");
if (loop != 0 ||
length < 1 ||
length > 7 ||
(unsigned long) addr < 4096)
break;
if (gdbstub_clear_breakpoint((u8 *) addr, length) < 0)
break;
gdbstub_strcpy(output_buffer, "OK");
break;
default:
gdbstub_proto("### GDB Unsupported Cmd '%s'\n",
input_buffer);
break;
}
/* reply to the request */
putpacket(output_buffer);
}
done:
/*
* Need to flush the instruction cache here, as we may
* have deposited a breakpoint, and the icache probably
* has no way of knowing that a data ref to some location
* may have changed something that is in the instruction
* cache.
* NB: We flush both caches, just to be sure...
*/
if (gdbstub_flush_caches)
gdbstub_purge_cache();
gdbstub_load_fpu();
mn10300_set_gdbleds(0);
if (excep == EXCEP_NMI)
NMICR = NMICR_NMIF;
touch_softlockup_watchdog();
local_irq_restore(epsw);
return 1;
}
/*
* handle event interception
*/
asmlinkage int gdbstub_intercept(struct pt_regs *regs,
enum exception_code excep)
{
static u8 notfirst = 1;
int ret;
if (gdbstub_busy)
gdbstub_printk("--> gdbstub reentered itself\n");
gdbstub_busy = 1;
if (notfirst) {
unsigned long mdr;
asm("mov mdr,%0" : "=d"(mdr));
gdbstub_entry(
"--> gdbstub_intercept(%p,%04x) [MDR=%lx PC=%lx]\n",
regs, excep, mdr, regs->pc);
gdbstub_entry(
"PC: %08lx EPSW: %08lx SSP: %08lx mode: %s\n",
regs->pc, regs->epsw, (unsigned long) &ret,
user_mode(regs) ? "User" : "Super");
gdbstub_entry(
"d0: %08lx d1: %08lx d2: %08lx d3: %08lx\n",
regs->d0, regs->d1, regs->d2, regs->d3);
gdbstub_entry(
"a0: %08lx a1: %08lx a2: %08lx a3: %08lx\n",
regs->a0, regs->a1, regs->a2, regs->a3);
gdbstub_entry(
"e0: %08lx e1: %08lx e2: %08lx e3: %08lx\n",
regs->e0, regs->e1, regs->e2, regs->e3);
gdbstub_entry(
"e4: %08lx e5: %08lx e6: %08lx e7: %08lx\n",
regs->e4, regs->e5, regs->e6, regs->e7);
gdbstub_entry(
"lar: %08lx lir: %08lx mdr: %08lx usp: %08lx\n",
regs->lar, regs->lir, regs->mdr, regs->sp);
gdbstub_entry(
"cvf: %08lx crl: %08lx crh: %08lx drq: %08lx\n",
regs->mcvf, regs->mcrl, regs->mcrh, regs->mdrq);
gdbstub_entry(
"threadinfo=%p task=%p)\n",
current_thread_info(), current);
} else {
notfirst = 1;
}
ret = gdbstub(regs, excep);
gdbstub_entry("<-- gdbstub_intercept()\n");
gdbstub_busy = 0;
return ret;
}
/*
* handle the GDB stub itself causing an exception
*/
asmlinkage void gdbstub_exception(struct pt_regs *regs,
enum exception_code excep)
{
unsigned long mdr;
asm("mov mdr,%0" : "=d"(mdr));
gdbstub_entry("--> gdbstub exception({%p},%04x) [MDR=%lx]\n",
regs, excep, mdr);
while ((unsigned long) regs == 0xffffffff) {}
/* handle guarded memory accesses where we know it might fault */
if (regs->pc == (unsigned) gdbstub_read_byte_guard) {
regs->pc = (unsigned) gdbstub_read_byte_cont;
goto fault;
}
if (regs->pc == (unsigned) gdbstub_read_word_guard) {
regs->pc = (unsigned) gdbstub_read_word_cont;
goto fault;
}
if (regs->pc == (unsigned) gdbstub_read_dword_guard) {
regs->pc = (unsigned) gdbstub_read_dword_cont;
goto fault;
}
if (regs->pc == (unsigned) gdbstub_write_byte_guard) {
regs->pc = (unsigned) gdbstub_write_byte_cont;
goto fault;
}
if (regs->pc == (unsigned) gdbstub_write_word_guard) {
regs->pc = (unsigned) gdbstub_write_word_cont;
goto fault;
}
if (regs->pc == (unsigned) gdbstub_write_dword_guard) {
regs->pc = (unsigned) gdbstub_write_dword_cont;
goto fault;
}
gdbstub_printk("\n### GDB stub caused an exception ###\n");
/* something went horribly wrong */
console_verbose();
show_registers(regs);
panic("GDB Stub caused an unexpected exception - can't continue\n");
/* we caught an attempt by the stub to access silly memory */
fault:
gdbstub_entry("<-- gdbstub exception() = EFAULT\n");
regs->d0 = -EFAULT;
return;
}
/*
* send an exit message to GDB
*/
void gdbstub_exit(int status)
{
unsigned char checksum;
unsigned char ch;
int count;
gdbstub_busy = 1;
output_buffer[0] = 'W';
output_buffer[1] = hex_asc_hi(status);
output_buffer[2] = hex_asc_lo(status);
output_buffer[3] = 0;
gdbstub_io_tx_char('$');
checksum = 0;
count = 0;
while ((ch = output_buffer[count]) != 0) {
gdbstub_io_tx_char(ch);
checksum += ch;
count += 1;
}
gdbstub_io_tx_char('#');
gdbstub_io_tx_char(hex_asc_hi(checksum));
gdbstub_io_tx_char(hex_asc_lo(checksum));
/* make sure the output is flushed, or else RedBoot might clobber it */
gdbstub_io_tx_flush();
gdbstub_busy = 0;
}
/*
* initialise the GDB stub
*/
asmlinkage void __init gdbstub_init(void)
{
#ifdef CONFIG_GDBSTUB_IMMEDIATE
unsigned char ch;
int ret;
#endif
gdbstub_busy = 1;
printk(KERN_INFO "%s", gdbstub_banner);
gdbstub_io_init();
gdbstub_entry("--> gdbstub_init\n");
/* try to talk to GDB (or anyone insane enough to want to type GDB
* protocol by hand) */
gdbstub_io("### GDB Tx ACK\n");
gdbstub_io_tx_char('+'); /* 'hello world' */
#ifdef CONFIG_GDBSTUB_IMMEDIATE
gdbstub_printk("GDB Stub waiting for packet\n");
/* in case GDB is started before us, ACK any packets that are already
* sitting there (presumably "$?#xx")
*/
do { gdbstub_io_rx_char(&ch, 0); } while (ch != '$');
do { gdbstub_io_rx_char(&ch, 0); } while (ch != '#');
/* eat first csum byte */
do { ret = gdbstub_io_rx_char(&ch, 0); } while (ret != 0);
/* eat second csum byte */
do { ret = gdbstub_io_rx_char(&ch, 0); } while (ret != 0);
gdbstub_io("### GDB Tx NAK\n");
gdbstub_io_tx_char('-'); /* NAK it */
#else
printk("GDB Stub ready\n");
#endif
gdbstub_busy = 0;
gdbstub_entry("<-- gdbstub_init\n");
}
/*
* register the console at a more appropriate time
*/
#ifdef CONFIG_GDBSTUB_CONSOLE
static int __init gdbstub_postinit(void)
{
printk(KERN_NOTICE "registering console\n");
register_console(&gdbstub_console);
return 0;
}
__initcall(gdbstub_postinit);
#endif
/*
* handle character reception on GDB serial port
* - jump into the GDB stub if BREAK is detected on the serial line
*/
asmlinkage void gdbstub_rx_irq(struct pt_regs *regs, enum exception_code excep)
{
char ch;
int ret;
gdbstub_entry("--> gdbstub_rx_irq\n");
do {
ret = gdbstub_io_rx_char(&ch, 1);
if (ret != -EIO && ret != -EAGAIN) {
if (ret != -EINTR)
gdbstub_rx_unget = ch;
gdbstub(regs, excep);
}
} while (ret != -EAGAIN);
gdbstub_entry("<-- gdbstub_rx_irq\n");
}