linux/drivers/spi/spi-s3c64xx.c
Marek Szyprowski 3d63a47a38 spi: s3c64xx: Don't request/release DMA channels for each SPI transfer
Requesting a DMA channel might be a time consuming operation, so there is
no need to acquire and release DMA channel for each SPI transfer.
DMA channels can be requested during driver probe and kept all the time,
also because there are no shared nor dynamically allocated channels on
Samsung S3C/S5P/Exynos platforms.

While moving dma_requrest_slave_channel calls, lets switch to
dma_request_slave_channel_reason(), which returns error codes on failure,
which can be properly propagated to the caller (this for example defers
SPI probe when DMA controller is not yet available).

Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Andi Shyti <andi.shyti@samsung.com>
Tested-by: Andi Shyti <andi.shyti@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-01-09 12:21:04 +00:00

1442 lines
38 KiB
C

/*
* Copyright (C) 2009 Samsung Electronics Ltd.
* Jaswinder Singh <jassi.brar@samsung.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/init.h>
#include <linux/module.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/clk.h>
#include <linux/dma-mapping.h>
#include <linux/dmaengine.h>
#include <linux/platform_device.h>
#include <linux/pm_runtime.h>
#include <linux/spi/spi.h>
#include <linux/gpio.h>
#include <linux/of.h>
#include <linux/of_gpio.h>
#include <linux/platform_data/spi-s3c64xx.h>
#define MAX_SPI_PORTS 6
#define S3C64XX_SPI_QUIRK_POLL (1 << 0)
#define S3C64XX_SPI_QUIRK_CS_AUTO (1 << 1)
#define AUTOSUSPEND_TIMEOUT 2000
/* Registers and bit-fields */
#define S3C64XX_SPI_CH_CFG 0x00
#define S3C64XX_SPI_CLK_CFG 0x04
#define S3C64XX_SPI_MODE_CFG 0x08
#define S3C64XX_SPI_SLAVE_SEL 0x0C
#define S3C64XX_SPI_INT_EN 0x10
#define S3C64XX_SPI_STATUS 0x14
#define S3C64XX_SPI_TX_DATA 0x18
#define S3C64XX_SPI_RX_DATA 0x1C
#define S3C64XX_SPI_PACKET_CNT 0x20
#define S3C64XX_SPI_PENDING_CLR 0x24
#define S3C64XX_SPI_SWAP_CFG 0x28
#define S3C64XX_SPI_FB_CLK 0x2C
#define S3C64XX_SPI_CH_HS_EN (1<<6) /* High Speed Enable */
#define S3C64XX_SPI_CH_SW_RST (1<<5)
#define S3C64XX_SPI_CH_SLAVE (1<<4)
#define S3C64XX_SPI_CPOL_L (1<<3)
#define S3C64XX_SPI_CPHA_B (1<<2)
#define S3C64XX_SPI_CH_RXCH_ON (1<<1)
#define S3C64XX_SPI_CH_TXCH_ON (1<<0)
#define S3C64XX_SPI_CLKSEL_SRCMSK (3<<9)
#define S3C64XX_SPI_CLKSEL_SRCSHFT 9
#define S3C64XX_SPI_ENCLK_ENABLE (1<<8)
#define S3C64XX_SPI_PSR_MASK 0xff
#define S3C64XX_SPI_MODE_CH_TSZ_BYTE (0<<29)
#define S3C64XX_SPI_MODE_CH_TSZ_HALFWORD (1<<29)
#define S3C64XX_SPI_MODE_CH_TSZ_WORD (2<<29)
#define S3C64XX_SPI_MODE_CH_TSZ_MASK (3<<29)
#define S3C64XX_SPI_MODE_BUS_TSZ_BYTE (0<<17)
#define S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD (1<<17)
#define S3C64XX_SPI_MODE_BUS_TSZ_WORD (2<<17)
#define S3C64XX_SPI_MODE_BUS_TSZ_MASK (3<<17)
#define S3C64XX_SPI_MODE_RXDMA_ON (1<<2)
#define S3C64XX_SPI_MODE_TXDMA_ON (1<<1)
#define S3C64XX_SPI_MODE_4BURST (1<<0)
#define S3C64XX_SPI_SLAVE_AUTO (1<<1)
#define S3C64XX_SPI_SLAVE_SIG_INACT (1<<0)
#define S3C64XX_SPI_SLAVE_NSC_CNT_2 (2<<4)
#define S3C64XX_SPI_INT_TRAILING_EN (1<<6)
#define S3C64XX_SPI_INT_RX_OVERRUN_EN (1<<5)
#define S3C64XX_SPI_INT_RX_UNDERRUN_EN (1<<4)
#define S3C64XX_SPI_INT_TX_OVERRUN_EN (1<<3)
#define S3C64XX_SPI_INT_TX_UNDERRUN_EN (1<<2)
#define S3C64XX_SPI_INT_RX_FIFORDY_EN (1<<1)
#define S3C64XX_SPI_INT_TX_FIFORDY_EN (1<<0)
#define S3C64XX_SPI_ST_RX_OVERRUN_ERR (1<<5)
#define S3C64XX_SPI_ST_RX_UNDERRUN_ERR (1<<4)
#define S3C64XX_SPI_ST_TX_OVERRUN_ERR (1<<3)
#define S3C64XX_SPI_ST_TX_UNDERRUN_ERR (1<<2)
#define S3C64XX_SPI_ST_RX_FIFORDY (1<<1)
#define S3C64XX_SPI_ST_TX_FIFORDY (1<<0)
#define S3C64XX_SPI_PACKET_CNT_EN (1<<16)
#define S3C64XX_SPI_PND_TX_UNDERRUN_CLR (1<<4)
#define S3C64XX_SPI_PND_TX_OVERRUN_CLR (1<<3)
#define S3C64XX_SPI_PND_RX_UNDERRUN_CLR (1<<2)
#define S3C64XX_SPI_PND_RX_OVERRUN_CLR (1<<1)
#define S3C64XX_SPI_PND_TRAILING_CLR (1<<0)
#define S3C64XX_SPI_SWAP_RX_HALF_WORD (1<<7)
#define S3C64XX_SPI_SWAP_RX_BYTE (1<<6)
#define S3C64XX_SPI_SWAP_RX_BIT (1<<5)
#define S3C64XX_SPI_SWAP_RX_EN (1<<4)
#define S3C64XX_SPI_SWAP_TX_HALF_WORD (1<<3)
#define S3C64XX_SPI_SWAP_TX_BYTE (1<<2)
#define S3C64XX_SPI_SWAP_TX_BIT (1<<1)
#define S3C64XX_SPI_SWAP_TX_EN (1<<0)
#define S3C64XX_SPI_FBCLK_MSK (3<<0)
#define FIFO_LVL_MASK(i) ((i)->port_conf->fifo_lvl_mask[i->port_id])
#define S3C64XX_SPI_ST_TX_DONE(v, i) (((v) & \
(1 << (i)->port_conf->tx_st_done)) ? 1 : 0)
#define TX_FIFO_LVL(v, i) (((v) >> 6) & FIFO_LVL_MASK(i))
#define RX_FIFO_LVL(v, i) (((v) >> (i)->port_conf->rx_lvl_offset) & \
FIFO_LVL_MASK(i))
#define S3C64XX_SPI_MAX_TRAILCNT 0x3ff
#define S3C64XX_SPI_TRAILCNT_OFF 19
#define S3C64XX_SPI_TRAILCNT S3C64XX_SPI_MAX_TRAILCNT
#define msecs_to_loops(t) (loops_per_jiffy / 1000 * HZ * t)
#define is_polling(x) (x->port_conf->quirks & S3C64XX_SPI_QUIRK_POLL)
#define RXBUSY (1<<2)
#define TXBUSY (1<<3)
struct s3c64xx_spi_dma_data {
struct dma_chan *ch;
enum dma_transfer_direction direction;
};
/**
* struct s3c64xx_spi_info - SPI Controller hardware info
* @fifo_lvl_mask: Bit-mask for {TX|RX}_FIFO_LVL bits in SPI_STATUS register.
* @rx_lvl_offset: Bit offset of RX_FIFO_LVL bits in SPI_STATUS regiter.
* @tx_st_done: Bit offset of TX_DONE bit in SPI_STATUS regiter.
* @high_speed: True, if the controller supports HIGH_SPEED_EN bit.
* @clk_from_cmu: True, if the controller does not include a clock mux and
* prescaler unit.
*
* The Samsung s3c64xx SPI controller are used on various Samsung SoC's but
* differ in some aspects such as the size of the fifo and spi bus clock
* setup. Such differences are specified to the driver using this structure
* which is provided as driver data to the driver.
*/
struct s3c64xx_spi_port_config {
int fifo_lvl_mask[MAX_SPI_PORTS];
int rx_lvl_offset;
int tx_st_done;
int quirks;
bool high_speed;
bool clk_from_cmu;
bool clk_ioclk;
};
/**
* struct s3c64xx_spi_driver_data - Runtime info holder for SPI driver.
* @clk: Pointer to the spi clock.
* @src_clk: Pointer to the clock used to generate SPI signals.
* @ioclk: Pointer to the i/o clock between master and slave
* @master: Pointer to the SPI Protocol master.
* @cntrlr_info: Platform specific data for the controller this driver manages.
* @tgl_spi: Pointer to the last CS left untoggled by the cs_change hint.
* @lock: Controller specific lock.
* @state: Set of FLAGS to indicate status.
* @rx_dmach: Controller's DMA channel for Rx.
* @tx_dmach: Controller's DMA channel for Tx.
* @sfr_start: BUS address of SPI controller regs.
* @regs: Pointer to ioremap'ed controller registers.
* @irq: interrupt
* @xfer_completion: To indicate completion of xfer task.
* @cur_mode: Stores the active configuration of the controller.
* @cur_bpw: Stores the active bits per word settings.
* @cur_speed: Stores the active xfer clock speed.
*/
struct s3c64xx_spi_driver_data {
void __iomem *regs;
struct clk *clk;
struct clk *src_clk;
struct clk *ioclk;
struct platform_device *pdev;
struct spi_master *master;
struct s3c64xx_spi_info *cntrlr_info;
struct spi_device *tgl_spi;
spinlock_t lock;
unsigned long sfr_start;
struct completion xfer_completion;
unsigned state;
unsigned cur_mode, cur_bpw;
unsigned cur_speed;
struct s3c64xx_spi_dma_data rx_dma;
struct s3c64xx_spi_dma_data tx_dma;
struct s3c64xx_spi_port_config *port_conf;
unsigned int port_id;
};
static void flush_fifo(struct s3c64xx_spi_driver_data *sdd)
{
void __iomem *regs = sdd->regs;
unsigned long loops;
u32 val;
writel(0, regs + S3C64XX_SPI_PACKET_CNT);
val = readl(regs + S3C64XX_SPI_CH_CFG);
val &= ~(S3C64XX_SPI_CH_RXCH_ON | S3C64XX_SPI_CH_TXCH_ON);
writel(val, regs + S3C64XX_SPI_CH_CFG);
val = readl(regs + S3C64XX_SPI_CH_CFG);
val |= S3C64XX_SPI_CH_SW_RST;
val &= ~S3C64XX_SPI_CH_HS_EN;
writel(val, regs + S3C64XX_SPI_CH_CFG);
/* Flush TxFIFO*/
loops = msecs_to_loops(1);
do {
val = readl(regs + S3C64XX_SPI_STATUS);
} while (TX_FIFO_LVL(val, sdd) && loops--);
if (loops == 0)
dev_warn(&sdd->pdev->dev, "Timed out flushing TX FIFO\n");
/* Flush RxFIFO*/
loops = msecs_to_loops(1);
do {
val = readl(regs + S3C64XX_SPI_STATUS);
if (RX_FIFO_LVL(val, sdd))
readl(regs + S3C64XX_SPI_RX_DATA);
else
break;
} while (loops--);
if (loops == 0)
dev_warn(&sdd->pdev->dev, "Timed out flushing RX FIFO\n");
val = readl(regs + S3C64XX_SPI_CH_CFG);
val &= ~S3C64XX_SPI_CH_SW_RST;
writel(val, regs + S3C64XX_SPI_CH_CFG);
val = readl(regs + S3C64XX_SPI_MODE_CFG);
val &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON);
writel(val, regs + S3C64XX_SPI_MODE_CFG);
}
static void s3c64xx_spi_dmacb(void *data)
{
struct s3c64xx_spi_driver_data *sdd;
struct s3c64xx_spi_dma_data *dma = data;
unsigned long flags;
if (dma->direction == DMA_DEV_TO_MEM)
sdd = container_of(data,
struct s3c64xx_spi_driver_data, rx_dma);
else
sdd = container_of(data,
struct s3c64xx_spi_driver_data, tx_dma);
spin_lock_irqsave(&sdd->lock, flags);
if (dma->direction == DMA_DEV_TO_MEM) {
sdd->state &= ~RXBUSY;
if (!(sdd->state & TXBUSY))
complete(&sdd->xfer_completion);
} else {
sdd->state &= ~TXBUSY;
if (!(sdd->state & RXBUSY))
complete(&sdd->xfer_completion);
}
spin_unlock_irqrestore(&sdd->lock, flags);
}
static void prepare_dma(struct s3c64xx_spi_dma_data *dma,
struct sg_table *sgt)
{
struct s3c64xx_spi_driver_data *sdd;
struct dma_slave_config config;
struct dma_async_tx_descriptor *desc;
memset(&config, 0, sizeof(config));
if (dma->direction == DMA_DEV_TO_MEM) {
sdd = container_of((void *)dma,
struct s3c64xx_spi_driver_data, rx_dma);
config.direction = dma->direction;
config.src_addr = sdd->sfr_start + S3C64XX_SPI_RX_DATA;
config.src_addr_width = sdd->cur_bpw / 8;
config.src_maxburst = 1;
dmaengine_slave_config(dma->ch, &config);
} else {
sdd = container_of((void *)dma,
struct s3c64xx_spi_driver_data, tx_dma);
config.direction = dma->direction;
config.dst_addr = sdd->sfr_start + S3C64XX_SPI_TX_DATA;
config.dst_addr_width = sdd->cur_bpw / 8;
config.dst_maxburst = 1;
dmaengine_slave_config(dma->ch, &config);
}
desc = dmaengine_prep_slave_sg(dma->ch, sgt->sgl, sgt->nents,
dma->direction, DMA_PREP_INTERRUPT);
desc->callback = s3c64xx_spi_dmacb;
desc->callback_param = dma;
dmaengine_submit(desc);
dma_async_issue_pending(dma->ch);
}
static void s3c64xx_spi_set_cs(struct spi_device *spi, bool enable)
{
struct s3c64xx_spi_driver_data *sdd =
spi_master_get_devdata(spi->master);
if (sdd->cntrlr_info->no_cs)
return;
if (enable) {
if (!(sdd->port_conf->quirks & S3C64XX_SPI_QUIRK_CS_AUTO)) {
writel(0, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
} else {
u32 ssel = readl(sdd->regs + S3C64XX_SPI_SLAVE_SEL);
ssel |= (S3C64XX_SPI_SLAVE_AUTO |
S3C64XX_SPI_SLAVE_NSC_CNT_2);
writel(ssel, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
}
} else {
if (!(sdd->port_conf->quirks & S3C64XX_SPI_QUIRK_CS_AUTO))
writel(S3C64XX_SPI_SLAVE_SIG_INACT,
sdd->regs + S3C64XX_SPI_SLAVE_SEL);
}
}
static int s3c64xx_spi_prepare_transfer(struct spi_master *spi)
{
struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(spi);
if (is_polling(sdd))
return 0;
spi->dma_rx = sdd->rx_dma.ch;
spi->dma_tx = sdd->tx_dma.ch;
return 0;
}
static bool s3c64xx_spi_can_dma(struct spi_master *master,
struct spi_device *spi,
struct spi_transfer *xfer)
{
struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
return xfer->len > (FIFO_LVL_MASK(sdd) >> 1) + 1;
}
static void enable_datapath(struct s3c64xx_spi_driver_data *sdd,
struct spi_device *spi,
struct spi_transfer *xfer, int dma_mode)
{
void __iomem *regs = sdd->regs;
u32 modecfg, chcfg;
modecfg = readl(regs + S3C64XX_SPI_MODE_CFG);
modecfg &= ~(S3C64XX_SPI_MODE_TXDMA_ON | S3C64XX_SPI_MODE_RXDMA_ON);
chcfg = readl(regs + S3C64XX_SPI_CH_CFG);
chcfg &= ~S3C64XX_SPI_CH_TXCH_ON;
if (dma_mode) {
chcfg &= ~S3C64XX_SPI_CH_RXCH_ON;
} else {
/* Always shift in data in FIFO, even if xfer is Tx only,
* this helps setting PCKT_CNT value for generating clocks
* as exactly needed.
*/
chcfg |= S3C64XX_SPI_CH_RXCH_ON;
writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
| S3C64XX_SPI_PACKET_CNT_EN,
regs + S3C64XX_SPI_PACKET_CNT);
}
if (xfer->tx_buf != NULL) {
sdd->state |= TXBUSY;
chcfg |= S3C64XX_SPI_CH_TXCH_ON;
if (dma_mode) {
modecfg |= S3C64XX_SPI_MODE_TXDMA_ON;
prepare_dma(&sdd->tx_dma, &xfer->tx_sg);
} else {
switch (sdd->cur_bpw) {
case 32:
iowrite32_rep(regs + S3C64XX_SPI_TX_DATA,
xfer->tx_buf, xfer->len / 4);
break;
case 16:
iowrite16_rep(regs + S3C64XX_SPI_TX_DATA,
xfer->tx_buf, xfer->len / 2);
break;
default:
iowrite8_rep(regs + S3C64XX_SPI_TX_DATA,
xfer->tx_buf, xfer->len);
break;
}
}
}
if (xfer->rx_buf != NULL) {
sdd->state |= RXBUSY;
if (sdd->port_conf->high_speed && sdd->cur_speed >= 30000000UL
&& !(sdd->cur_mode & SPI_CPHA))
chcfg |= S3C64XX_SPI_CH_HS_EN;
if (dma_mode) {
modecfg |= S3C64XX_SPI_MODE_RXDMA_ON;
chcfg |= S3C64XX_SPI_CH_RXCH_ON;
writel(((xfer->len * 8 / sdd->cur_bpw) & 0xffff)
| S3C64XX_SPI_PACKET_CNT_EN,
regs + S3C64XX_SPI_PACKET_CNT);
prepare_dma(&sdd->rx_dma, &xfer->rx_sg);
}
}
writel(modecfg, regs + S3C64XX_SPI_MODE_CFG);
writel(chcfg, regs + S3C64XX_SPI_CH_CFG);
}
static u32 s3c64xx_spi_wait_for_timeout(struct s3c64xx_spi_driver_data *sdd,
int timeout_ms)
{
void __iomem *regs = sdd->regs;
unsigned long val = 1;
u32 status;
/* max fifo depth available */
u32 max_fifo = (FIFO_LVL_MASK(sdd) >> 1) + 1;
if (timeout_ms)
val = msecs_to_loops(timeout_ms);
do {
status = readl(regs + S3C64XX_SPI_STATUS);
} while (RX_FIFO_LVL(status, sdd) < max_fifo && --val);
/* return the actual received data length */
return RX_FIFO_LVL(status, sdd);
}
static int wait_for_dma(struct s3c64xx_spi_driver_data *sdd,
struct spi_transfer *xfer)
{
void __iomem *regs = sdd->regs;
unsigned long val;
u32 status;
int ms;
/* millisecs to xfer 'len' bytes @ 'cur_speed' */
ms = xfer->len * 8 * 1000 / sdd->cur_speed;
ms += 10; /* some tolerance */
val = msecs_to_jiffies(ms) + 10;
val = wait_for_completion_timeout(&sdd->xfer_completion, val);
/*
* If the previous xfer was completed within timeout, then
* proceed further else return -EIO.
* DmaTx returns after simply writing data in the FIFO,
* w/o waiting for real transmission on the bus to finish.
* DmaRx returns only after Dma read data from FIFO which
* needs bus transmission to finish, so we don't worry if
* Xfer involved Rx(with or without Tx).
*/
if (val && !xfer->rx_buf) {
val = msecs_to_loops(10);
status = readl(regs + S3C64XX_SPI_STATUS);
while ((TX_FIFO_LVL(status, sdd)
|| !S3C64XX_SPI_ST_TX_DONE(status, sdd))
&& --val) {
cpu_relax();
status = readl(regs + S3C64XX_SPI_STATUS);
}
}
/* If timed out while checking rx/tx status return error */
if (!val)
return -EIO;
return 0;
}
static int wait_for_pio(struct s3c64xx_spi_driver_data *sdd,
struct spi_transfer *xfer)
{
void __iomem *regs = sdd->regs;
unsigned long val;
u32 status;
int loops;
u32 cpy_len;
u8 *buf;
int ms;
/* millisecs to xfer 'len' bytes @ 'cur_speed' */
ms = xfer->len * 8 * 1000 / sdd->cur_speed;
ms += 10; /* some tolerance */
val = msecs_to_loops(ms);
do {
status = readl(regs + S3C64XX_SPI_STATUS);
} while (RX_FIFO_LVL(status, sdd) < xfer->len && --val);
/* If it was only Tx */
if (!xfer->rx_buf) {
sdd->state &= ~TXBUSY;
return 0;
}
/*
* If the receive length is bigger than the controller fifo
* size, calculate the loops and read the fifo as many times.
* loops = length / max fifo size (calculated by using the
* fifo mask).
* For any size less than the fifo size the below code is
* executed atleast once.
*/
loops = xfer->len / ((FIFO_LVL_MASK(sdd) >> 1) + 1);
buf = xfer->rx_buf;
do {
/* wait for data to be received in the fifo */
cpy_len = s3c64xx_spi_wait_for_timeout(sdd,
(loops ? ms : 0));
switch (sdd->cur_bpw) {
case 32:
ioread32_rep(regs + S3C64XX_SPI_RX_DATA,
buf, cpy_len / 4);
break;
case 16:
ioread16_rep(regs + S3C64XX_SPI_RX_DATA,
buf, cpy_len / 2);
break;
default:
ioread8_rep(regs + S3C64XX_SPI_RX_DATA,
buf, cpy_len);
break;
}
buf = buf + cpy_len;
} while (loops--);
sdd->state &= ~RXBUSY;
return 0;
}
static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
{
void __iomem *regs = sdd->regs;
u32 val;
/* Disable Clock */
if (!sdd->port_conf->clk_from_cmu) {
val = readl(regs + S3C64XX_SPI_CLK_CFG);
val &= ~S3C64XX_SPI_ENCLK_ENABLE;
writel(val, regs + S3C64XX_SPI_CLK_CFG);
}
/* Set Polarity and Phase */
val = readl(regs + S3C64XX_SPI_CH_CFG);
val &= ~(S3C64XX_SPI_CH_SLAVE |
S3C64XX_SPI_CPOL_L |
S3C64XX_SPI_CPHA_B);
if (sdd->cur_mode & SPI_CPOL)
val |= S3C64XX_SPI_CPOL_L;
if (sdd->cur_mode & SPI_CPHA)
val |= S3C64XX_SPI_CPHA_B;
writel(val, regs + S3C64XX_SPI_CH_CFG);
/* Set Channel & DMA Mode */
val = readl(regs + S3C64XX_SPI_MODE_CFG);
val &= ~(S3C64XX_SPI_MODE_BUS_TSZ_MASK
| S3C64XX_SPI_MODE_CH_TSZ_MASK);
switch (sdd->cur_bpw) {
case 32:
val |= S3C64XX_SPI_MODE_BUS_TSZ_WORD;
val |= S3C64XX_SPI_MODE_CH_TSZ_WORD;
break;
case 16:
val |= S3C64XX_SPI_MODE_BUS_TSZ_HALFWORD;
val |= S3C64XX_SPI_MODE_CH_TSZ_HALFWORD;
break;
default:
val |= S3C64XX_SPI_MODE_BUS_TSZ_BYTE;
val |= S3C64XX_SPI_MODE_CH_TSZ_BYTE;
break;
}
writel(val, regs + S3C64XX_SPI_MODE_CFG);
if (sdd->port_conf->clk_from_cmu) {
/* The src_clk clock is divided internally by 2 */
clk_set_rate(sdd->src_clk, sdd->cur_speed * 2);
} else {
/* Configure Clock */
val = readl(regs + S3C64XX_SPI_CLK_CFG);
val &= ~S3C64XX_SPI_PSR_MASK;
val |= ((clk_get_rate(sdd->src_clk) / sdd->cur_speed / 2 - 1)
& S3C64XX_SPI_PSR_MASK);
writel(val, regs + S3C64XX_SPI_CLK_CFG);
/* Enable Clock */
val = readl(regs + S3C64XX_SPI_CLK_CFG);
val |= S3C64XX_SPI_ENCLK_ENABLE;
writel(val, regs + S3C64XX_SPI_CLK_CFG);
}
}
#define XFER_DMAADDR_INVALID DMA_BIT_MASK(32)
static int s3c64xx_spi_prepare_message(struct spi_master *master,
struct spi_message *msg)
{
struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
struct spi_device *spi = msg->spi;
struct s3c64xx_spi_csinfo *cs = spi->controller_data;
/* Configure feedback delay */
writel(cs->fb_delay & 0x3, sdd->regs + S3C64XX_SPI_FB_CLK);
return 0;
}
static int s3c64xx_spi_transfer_one(struct spi_master *master,
struct spi_device *spi,
struct spi_transfer *xfer)
{
struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
int status;
u32 speed;
u8 bpw;
unsigned long flags;
int use_dma;
reinit_completion(&sdd->xfer_completion);
/* Only BPW and Speed may change across transfers */
bpw = xfer->bits_per_word;
speed = xfer->speed_hz;
if (bpw != sdd->cur_bpw || speed != sdd->cur_speed) {
sdd->cur_bpw = bpw;
sdd->cur_speed = speed;
sdd->cur_mode = spi->mode;
s3c64xx_spi_config(sdd);
}
/* Polling method for xfers not bigger than FIFO capacity */
use_dma = 0;
if (!is_polling(sdd) &&
(sdd->rx_dma.ch && sdd->tx_dma.ch &&
(xfer->len > ((FIFO_LVL_MASK(sdd) >> 1) + 1))))
use_dma = 1;
spin_lock_irqsave(&sdd->lock, flags);
/* Pending only which is to be done */
sdd->state &= ~RXBUSY;
sdd->state &= ~TXBUSY;
enable_datapath(sdd, spi, xfer, use_dma);
/* Start the signals */
s3c64xx_spi_set_cs(spi, true);
spin_unlock_irqrestore(&sdd->lock, flags);
if (use_dma)
status = wait_for_dma(sdd, xfer);
else
status = wait_for_pio(sdd, xfer);
if (status) {
dev_err(&spi->dev, "I/O Error: rx-%d tx-%d res:rx-%c tx-%c len-%d\n",
xfer->rx_buf ? 1 : 0, xfer->tx_buf ? 1 : 0,
(sdd->state & RXBUSY) ? 'f' : 'p',
(sdd->state & TXBUSY) ? 'f' : 'p',
xfer->len);
if (use_dma) {
if (xfer->tx_buf != NULL
&& (sdd->state & TXBUSY))
dmaengine_terminate_all(sdd->tx_dma.ch);
if (xfer->rx_buf != NULL
&& (sdd->state & RXBUSY))
dmaengine_terminate_all(sdd->rx_dma.ch);
}
} else {
flush_fifo(sdd);
}
return status;
}
static struct s3c64xx_spi_csinfo *s3c64xx_get_slave_ctrldata(
struct spi_device *spi)
{
struct s3c64xx_spi_csinfo *cs;
struct device_node *slave_np, *data_np = NULL;
u32 fb_delay = 0;
slave_np = spi->dev.of_node;
if (!slave_np) {
dev_err(&spi->dev, "device node not found\n");
return ERR_PTR(-EINVAL);
}
data_np = of_get_child_by_name(slave_np, "controller-data");
if (!data_np) {
dev_err(&spi->dev, "child node 'controller-data' not found\n");
return ERR_PTR(-EINVAL);
}
cs = kzalloc(sizeof(*cs), GFP_KERNEL);
if (!cs) {
of_node_put(data_np);
return ERR_PTR(-ENOMEM);
}
of_property_read_u32(data_np, "samsung,spi-feedback-delay", &fb_delay);
cs->fb_delay = fb_delay;
of_node_put(data_np);
return cs;
}
/*
* Here we only check the validity of requested configuration
* and save the configuration in a local data-structure.
* The controller is actually configured only just before we
* get a message to transfer.
*/
static int s3c64xx_spi_setup(struct spi_device *spi)
{
struct s3c64xx_spi_csinfo *cs = spi->controller_data;
struct s3c64xx_spi_driver_data *sdd;
struct s3c64xx_spi_info *sci;
int err;
sdd = spi_master_get_devdata(spi->master);
if (spi->dev.of_node) {
cs = s3c64xx_get_slave_ctrldata(spi);
spi->controller_data = cs;
} else if (cs) {
/* On non-DT platforms the SPI core will set spi->cs_gpio
* to -ENOENT. The GPIO pin used to drive the chip select
* is defined by using platform data so spi->cs_gpio value
* has to be override to have the proper GPIO pin number.
*/
spi->cs_gpio = cs->line;
}
if (IS_ERR_OR_NULL(cs)) {
dev_err(&spi->dev, "No CS for SPI(%d)\n", spi->chip_select);
return -ENODEV;
}
if (!spi_get_ctldata(spi)) {
if (gpio_is_valid(spi->cs_gpio)) {
err = gpio_request_one(spi->cs_gpio, GPIOF_OUT_INIT_HIGH,
dev_name(&spi->dev));
if (err) {
dev_err(&spi->dev,
"Failed to get /CS gpio [%d]: %d\n",
spi->cs_gpio, err);
goto err_gpio_req;
}
}
spi_set_ctldata(spi, cs);
}
sci = sdd->cntrlr_info;
pm_runtime_get_sync(&sdd->pdev->dev);
/* Check if we can provide the requested rate */
if (!sdd->port_conf->clk_from_cmu) {
u32 psr, speed;
/* Max possible */
speed = clk_get_rate(sdd->src_clk) / 2 / (0 + 1);
if (spi->max_speed_hz > speed)
spi->max_speed_hz = speed;
psr = clk_get_rate(sdd->src_clk) / 2 / spi->max_speed_hz - 1;
psr &= S3C64XX_SPI_PSR_MASK;
if (psr == S3C64XX_SPI_PSR_MASK)
psr--;
speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
if (spi->max_speed_hz < speed) {
if (psr+1 < S3C64XX_SPI_PSR_MASK) {
psr++;
} else {
err = -EINVAL;
goto setup_exit;
}
}
speed = clk_get_rate(sdd->src_clk) / 2 / (psr + 1);
if (spi->max_speed_hz >= speed) {
spi->max_speed_hz = speed;
} else {
dev_err(&spi->dev, "Can't set %dHz transfer speed\n",
spi->max_speed_hz);
err = -EINVAL;
goto setup_exit;
}
}
pm_runtime_mark_last_busy(&sdd->pdev->dev);
pm_runtime_put_autosuspend(&sdd->pdev->dev);
s3c64xx_spi_set_cs(spi, false);
return 0;
setup_exit:
pm_runtime_mark_last_busy(&sdd->pdev->dev);
pm_runtime_put_autosuspend(&sdd->pdev->dev);
/* setup() returns with device de-selected */
s3c64xx_spi_set_cs(spi, false);
if (gpio_is_valid(spi->cs_gpio))
gpio_free(spi->cs_gpio);
spi_set_ctldata(spi, NULL);
err_gpio_req:
if (spi->dev.of_node)
kfree(cs);
return err;
}
static void s3c64xx_spi_cleanup(struct spi_device *spi)
{
struct s3c64xx_spi_csinfo *cs = spi_get_ctldata(spi);
if (gpio_is_valid(spi->cs_gpio)) {
gpio_free(spi->cs_gpio);
if (spi->dev.of_node)
kfree(cs);
else {
/* On non-DT platforms, the SPI core sets
* spi->cs_gpio to -ENOENT and .setup()
* overrides it with the GPIO pin value
* passed using platform data.
*/
spi->cs_gpio = -ENOENT;
}
}
spi_set_ctldata(spi, NULL);
}
static irqreturn_t s3c64xx_spi_irq(int irq, void *data)
{
struct s3c64xx_spi_driver_data *sdd = data;
struct spi_master *spi = sdd->master;
unsigned int val, clr = 0;
val = readl(sdd->regs + S3C64XX_SPI_STATUS);
if (val & S3C64XX_SPI_ST_RX_OVERRUN_ERR) {
clr = S3C64XX_SPI_PND_RX_OVERRUN_CLR;
dev_err(&spi->dev, "RX overrun\n");
}
if (val & S3C64XX_SPI_ST_RX_UNDERRUN_ERR) {
clr |= S3C64XX_SPI_PND_RX_UNDERRUN_CLR;
dev_err(&spi->dev, "RX underrun\n");
}
if (val & S3C64XX_SPI_ST_TX_OVERRUN_ERR) {
clr |= S3C64XX_SPI_PND_TX_OVERRUN_CLR;
dev_err(&spi->dev, "TX overrun\n");
}
if (val & S3C64XX_SPI_ST_TX_UNDERRUN_ERR) {
clr |= S3C64XX_SPI_PND_TX_UNDERRUN_CLR;
dev_err(&spi->dev, "TX underrun\n");
}
/* Clear the pending irq by setting and then clearing it */
writel(clr, sdd->regs + S3C64XX_SPI_PENDING_CLR);
writel(0, sdd->regs + S3C64XX_SPI_PENDING_CLR);
return IRQ_HANDLED;
}
static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel)
{
struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
void __iomem *regs = sdd->regs;
unsigned int val;
sdd->cur_speed = 0;
if (sci->no_cs)
writel(0, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
else if (!(sdd->port_conf->quirks & S3C64XX_SPI_QUIRK_CS_AUTO))
writel(S3C64XX_SPI_SLAVE_SIG_INACT, sdd->regs + S3C64XX_SPI_SLAVE_SEL);
/* Disable Interrupts - we use Polling if not DMA mode */
writel(0, regs + S3C64XX_SPI_INT_EN);
if (!sdd->port_conf->clk_from_cmu)
writel(sci->src_clk_nr << S3C64XX_SPI_CLKSEL_SRCSHFT,
regs + S3C64XX_SPI_CLK_CFG);
writel(0, regs + S3C64XX_SPI_MODE_CFG);
writel(0, regs + S3C64XX_SPI_PACKET_CNT);
/* Clear any irq pending bits, should set and clear the bits */
val = S3C64XX_SPI_PND_RX_OVERRUN_CLR |
S3C64XX_SPI_PND_RX_UNDERRUN_CLR |
S3C64XX_SPI_PND_TX_OVERRUN_CLR |
S3C64XX_SPI_PND_TX_UNDERRUN_CLR;
writel(val, regs + S3C64XX_SPI_PENDING_CLR);
writel(0, regs + S3C64XX_SPI_PENDING_CLR);
writel(0, regs + S3C64XX_SPI_SWAP_CFG);
val = readl(regs + S3C64XX_SPI_MODE_CFG);
val &= ~S3C64XX_SPI_MODE_4BURST;
val &= ~(S3C64XX_SPI_MAX_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
val |= (S3C64XX_SPI_TRAILCNT << S3C64XX_SPI_TRAILCNT_OFF);
writel(val, regs + S3C64XX_SPI_MODE_CFG);
flush_fifo(sdd);
}
#ifdef CONFIG_OF
static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev)
{
struct s3c64xx_spi_info *sci;
u32 temp;
sci = devm_kzalloc(dev, sizeof(*sci), GFP_KERNEL);
if (!sci)
return ERR_PTR(-ENOMEM);
if (of_property_read_u32(dev->of_node, "samsung,spi-src-clk", &temp)) {
dev_warn(dev, "spi bus clock parent not specified, using clock at index 0 as parent\n");
sci->src_clk_nr = 0;
} else {
sci->src_clk_nr = temp;
}
if (of_property_read_u32(dev->of_node, "num-cs", &temp)) {
dev_warn(dev, "number of chip select lines not specified, assuming 1 chip select line\n");
sci->num_cs = 1;
} else {
sci->num_cs = temp;
}
sci->no_cs = of_property_read_bool(dev->of_node, "broken-cs");
return sci;
}
#else
static struct s3c64xx_spi_info *s3c64xx_spi_parse_dt(struct device *dev)
{
return dev_get_platdata(dev);
}
#endif
static const struct of_device_id s3c64xx_spi_dt_match[];
static inline struct s3c64xx_spi_port_config *s3c64xx_spi_get_port_config(
struct platform_device *pdev)
{
#ifdef CONFIG_OF
if (pdev->dev.of_node) {
const struct of_device_id *match;
match = of_match_node(s3c64xx_spi_dt_match, pdev->dev.of_node);
return (struct s3c64xx_spi_port_config *)match->data;
}
#endif
return (struct s3c64xx_spi_port_config *)
platform_get_device_id(pdev)->driver_data;
}
static int s3c64xx_spi_probe(struct platform_device *pdev)
{
struct resource *mem_res;
struct s3c64xx_spi_driver_data *sdd;
struct s3c64xx_spi_info *sci = dev_get_platdata(&pdev->dev);
struct spi_master *master;
int ret, irq;
char clk_name[16];
if (!sci && pdev->dev.of_node) {
sci = s3c64xx_spi_parse_dt(&pdev->dev);
if (IS_ERR(sci))
return PTR_ERR(sci);
}
if (!sci) {
dev_err(&pdev->dev, "platform_data missing!\n");
return -ENODEV;
}
mem_res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (mem_res == NULL) {
dev_err(&pdev->dev, "Unable to get SPI MEM resource\n");
return -ENXIO;
}
irq = platform_get_irq(pdev, 0);
if (irq < 0) {
dev_warn(&pdev->dev, "Failed to get IRQ: %d\n", irq);
return irq;
}
master = spi_alloc_master(&pdev->dev,
sizeof(struct s3c64xx_spi_driver_data));
if (master == NULL) {
dev_err(&pdev->dev, "Unable to allocate SPI Master\n");
return -ENOMEM;
}
platform_set_drvdata(pdev, master);
sdd = spi_master_get_devdata(master);
sdd->port_conf = s3c64xx_spi_get_port_config(pdev);
sdd->master = master;
sdd->cntrlr_info = sci;
sdd->pdev = pdev;
sdd->sfr_start = mem_res->start;
if (pdev->dev.of_node) {
ret = of_alias_get_id(pdev->dev.of_node, "spi");
if (ret < 0) {
dev_err(&pdev->dev, "failed to get alias id, errno %d\n",
ret);
goto err_deref_master;
}
sdd->port_id = ret;
} else {
sdd->port_id = pdev->id;
}
sdd->cur_bpw = 8;
sdd->tx_dma.direction = DMA_MEM_TO_DEV;
sdd->rx_dma.direction = DMA_DEV_TO_MEM;
master->dev.of_node = pdev->dev.of_node;
master->bus_num = sdd->port_id;
master->setup = s3c64xx_spi_setup;
master->cleanup = s3c64xx_spi_cleanup;
master->prepare_transfer_hardware = s3c64xx_spi_prepare_transfer;
master->prepare_message = s3c64xx_spi_prepare_message;
master->transfer_one = s3c64xx_spi_transfer_one;
master->num_chipselect = sci->num_cs;
master->dma_alignment = 8;
master->bits_per_word_mask = SPI_BPW_MASK(32) | SPI_BPW_MASK(16) |
SPI_BPW_MASK(8);
/* the spi->mode bits understood by this driver: */
master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH;
master->auto_runtime_pm = true;
if (!is_polling(sdd))
master->can_dma = s3c64xx_spi_can_dma;
sdd->regs = devm_ioremap_resource(&pdev->dev, mem_res);
if (IS_ERR(sdd->regs)) {
ret = PTR_ERR(sdd->regs);
goto err_deref_master;
}
if (sci->cfg_gpio && sci->cfg_gpio()) {
dev_err(&pdev->dev, "Unable to config gpio\n");
ret = -EBUSY;
goto err_deref_master;
}
/* Setup clocks */
sdd->clk = devm_clk_get(&pdev->dev, "spi");
if (IS_ERR(sdd->clk)) {
dev_err(&pdev->dev, "Unable to acquire clock 'spi'\n");
ret = PTR_ERR(sdd->clk);
goto err_deref_master;
}
ret = clk_prepare_enable(sdd->clk);
if (ret) {
dev_err(&pdev->dev, "Couldn't enable clock 'spi'\n");
goto err_deref_master;
}
sprintf(clk_name, "spi_busclk%d", sci->src_clk_nr);
sdd->src_clk = devm_clk_get(&pdev->dev, clk_name);
if (IS_ERR(sdd->src_clk)) {
dev_err(&pdev->dev,
"Unable to acquire clock '%s'\n", clk_name);
ret = PTR_ERR(sdd->src_clk);
goto err_disable_clk;
}
ret = clk_prepare_enable(sdd->src_clk);
if (ret) {
dev_err(&pdev->dev, "Couldn't enable clock '%s'\n", clk_name);
goto err_disable_clk;
}
if (sdd->port_conf->clk_ioclk) {
sdd->ioclk = devm_clk_get(&pdev->dev, "spi_ioclk");
if (IS_ERR(sdd->ioclk)) {
dev_err(&pdev->dev, "Unable to acquire 'ioclk'\n");
ret = PTR_ERR(sdd->ioclk);
goto err_disable_src_clk;
}
ret = clk_prepare_enable(sdd->ioclk);
if (ret) {
dev_err(&pdev->dev, "Couldn't enable clock 'ioclk'\n");
goto err_disable_src_clk;
}
}
if (!is_polling(sdd)) {
/* Acquire DMA channels */
sdd->rx_dma.ch = dma_request_slave_channel_reason(&pdev->dev,
"rx");
if (IS_ERR(sdd->rx_dma.ch)) {
dev_err(&pdev->dev, "Failed to get RX DMA channel\n");
ret = PTR_ERR(sdd->rx_dma.ch);
goto err_disable_io_clk;
}
sdd->tx_dma.ch = dma_request_slave_channel_reason(&pdev->dev,
"tx");
if (IS_ERR(sdd->tx_dma.ch)) {
dev_err(&pdev->dev, "Failed to get TX DMA channel\n");
ret = PTR_ERR(sdd->tx_dma.ch);
goto err_release_tx_dma;
}
}
pm_runtime_set_autosuspend_delay(&pdev->dev, AUTOSUSPEND_TIMEOUT);
pm_runtime_use_autosuspend(&pdev->dev);
pm_runtime_set_active(&pdev->dev);
pm_runtime_enable(&pdev->dev);
pm_runtime_get_sync(&pdev->dev);
/* Setup Deufult Mode */
s3c64xx_spi_hwinit(sdd, sdd->port_id);
spin_lock_init(&sdd->lock);
init_completion(&sdd->xfer_completion);
ret = devm_request_irq(&pdev->dev, irq, s3c64xx_spi_irq, 0,
"spi-s3c64xx", sdd);
if (ret != 0) {
dev_err(&pdev->dev, "Failed to request IRQ %d: %d\n",
irq, ret);
goto err_pm_put;
}
writel(S3C64XX_SPI_INT_RX_OVERRUN_EN | S3C64XX_SPI_INT_RX_UNDERRUN_EN |
S3C64XX_SPI_INT_TX_OVERRUN_EN | S3C64XX_SPI_INT_TX_UNDERRUN_EN,
sdd->regs + S3C64XX_SPI_INT_EN);
ret = devm_spi_register_master(&pdev->dev, master);
if (ret != 0) {
dev_err(&pdev->dev, "cannot register SPI master: %d\n", ret);
goto err_pm_put;
}
dev_dbg(&pdev->dev, "Samsung SoC SPI Driver loaded for Bus SPI-%d with %d Slaves attached\n",
sdd->port_id, master->num_chipselect);
dev_dbg(&pdev->dev, "\tIOmem=[%pR]\tFIFO %dbytes\n",
mem_res, (FIFO_LVL_MASK(sdd) >> 1) + 1);
pm_runtime_mark_last_busy(&pdev->dev);
pm_runtime_put_autosuspend(&pdev->dev);
return 0;
err_pm_put:
pm_runtime_put_noidle(&pdev->dev);
pm_runtime_disable(&pdev->dev);
pm_runtime_set_suspended(&pdev->dev);
if (!is_polling(sdd))
dma_release_channel(sdd->rx_dma.ch);
err_release_tx_dma:
if (!is_polling(sdd))
dma_release_channel(sdd->tx_dma.ch);
err_disable_io_clk:
clk_disable_unprepare(sdd->ioclk);
err_disable_src_clk:
clk_disable_unprepare(sdd->src_clk);
err_disable_clk:
clk_disable_unprepare(sdd->clk);
err_deref_master:
spi_master_put(master);
return ret;
}
static int s3c64xx_spi_remove(struct platform_device *pdev)
{
struct spi_master *master = platform_get_drvdata(pdev);
struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
pm_runtime_get_sync(&pdev->dev);
writel(0, sdd->regs + S3C64XX_SPI_INT_EN);
if (!is_polling(sdd)) {
dma_release_channel(sdd->rx_dma.ch);
dma_release_channel(sdd->tx_dma.ch);
}
clk_disable_unprepare(sdd->ioclk);
clk_disable_unprepare(sdd->src_clk);
clk_disable_unprepare(sdd->clk);
pm_runtime_put_noidle(&pdev->dev);
pm_runtime_disable(&pdev->dev);
pm_runtime_set_suspended(&pdev->dev);
return 0;
}
#ifdef CONFIG_PM_SLEEP
static int s3c64xx_spi_suspend(struct device *dev)
{
struct spi_master *master = dev_get_drvdata(dev);
struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
int ret = spi_master_suspend(master);
if (ret)
return ret;
ret = pm_runtime_force_suspend(dev);
if (ret < 0)
return ret;
sdd->cur_speed = 0; /* Output Clock is stopped */
return 0;
}
static int s3c64xx_spi_resume(struct device *dev)
{
struct spi_master *master = dev_get_drvdata(dev);
struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
struct s3c64xx_spi_info *sci = sdd->cntrlr_info;
int ret;
if (sci->cfg_gpio)
sci->cfg_gpio();
ret = pm_runtime_force_resume(dev);
if (ret < 0)
return ret;
s3c64xx_spi_hwinit(sdd, sdd->port_id);
return spi_master_resume(master);
}
#endif /* CONFIG_PM_SLEEP */
#ifdef CONFIG_PM
static int s3c64xx_spi_runtime_suspend(struct device *dev)
{
struct spi_master *master = dev_get_drvdata(dev);
struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
clk_disable_unprepare(sdd->clk);
clk_disable_unprepare(sdd->src_clk);
clk_disable_unprepare(sdd->ioclk);
return 0;
}
static int s3c64xx_spi_runtime_resume(struct device *dev)
{
struct spi_master *master = dev_get_drvdata(dev);
struct s3c64xx_spi_driver_data *sdd = spi_master_get_devdata(master);
int ret;
if (sdd->port_conf->clk_ioclk) {
ret = clk_prepare_enable(sdd->ioclk);
if (ret != 0)
return ret;
}
ret = clk_prepare_enable(sdd->src_clk);
if (ret != 0)
goto err_disable_ioclk;
ret = clk_prepare_enable(sdd->clk);
if (ret != 0)
goto err_disable_src_clk;
return 0;
err_disable_src_clk:
clk_disable_unprepare(sdd->src_clk);
err_disable_ioclk:
clk_disable_unprepare(sdd->ioclk);
return ret;
}
#endif /* CONFIG_PM */
static const struct dev_pm_ops s3c64xx_spi_pm = {
SET_SYSTEM_SLEEP_PM_OPS(s3c64xx_spi_suspend, s3c64xx_spi_resume)
SET_RUNTIME_PM_OPS(s3c64xx_spi_runtime_suspend,
s3c64xx_spi_runtime_resume, NULL)
};
static struct s3c64xx_spi_port_config s3c2443_spi_port_config = {
.fifo_lvl_mask = { 0x7f },
.rx_lvl_offset = 13,
.tx_st_done = 21,
.high_speed = true,
};
static struct s3c64xx_spi_port_config s3c6410_spi_port_config = {
.fifo_lvl_mask = { 0x7f, 0x7F },
.rx_lvl_offset = 13,
.tx_st_done = 21,
};
static struct s3c64xx_spi_port_config s5pv210_spi_port_config = {
.fifo_lvl_mask = { 0x1ff, 0x7F },
.rx_lvl_offset = 15,
.tx_st_done = 25,
.high_speed = true,
};
static struct s3c64xx_spi_port_config exynos4_spi_port_config = {
.fifo_lvl_mask = { 0x1ff, 0x7F, 0x7F },
.rx_lvl_offset = 15,
.tx_st_done = 25,
.high_speed = true,
.clk_from_cmu = true,
};
static struct s3c64xx_spi_port_config exynos5440_spi_port_config = {
.fifo_lvl_mask = { 0x1ff },
.rx_lvl_offset = 15,
.tx_st_done = 25,
.high_speed = true,
.clk_from_cmu = true,
.quirks = S3C64XX_SPI_QUIRK_POLL,
};
static struct s3c64xx_spi_port_config exynos7_spi_port_config = {
.fifo_lvl_mask = { 0x1ff, 0x7F, 0x7F, 0x7F, 0x7F, 0x1ff},
.rx_lvl_offset = 15,
.tx_st_done = 25,
.high_speed = true,
.clk_from_cmu = true,
.quirks = S3C64XX_SPI_QUIRK_CS_AUTO,
};
static struct s3c64xx_spi_port_config exynos5433_spi_port_config = {
.fifo_lvl_mask = { 0x1ff, 0x7f, 0x7f, 0x7f, 0x7f, 0x1ff},
.rx_lvl_offset = 15,
.tx_st_done = 25,
.high_speed = true,
.clk_from_cmu = true,
.clk_ioclk = true,
.quirks = S3C64XX_SPI_QUIRK_CS_AUTO,
};
static const struct platform_device_id s3c64xx_spi_driver_ids[] = {
{
.name = "s3c2443-spi",
.driver_data = (kernel_ulong_t)&s3c2443_spi_port_config,
}, {
.name = "s3c6410-spi",
.driver_data = (kernel_ulong_t)&s3c6410_spi_port_config,
},
{ },
};
static const struct of_device_id s3c64xx_spi_dt_match[] = {
{ .compatible = "samsung,s3c2443-spi",
.data = (void *)&s3c2443_spi_port_config,
},
{ .compatible = "samsung,s3c6410-spi",
.data = (void *)&s3c6410_spi_port_config,
},
{ .compatible = "samsung,s5pv210-spi",
.data = (void *)&s5pv210_spi_port_config,
},
{ .compatible = "samsung,exynos4210-spi",
.data = (void *)&exynos4_spi_port_config,
},
{ .compatible = "samsung,exynos5440-spi",
.data = (void *)&exynos5440_spi_port_config,
},
{ .compatible = "samsung,exynos7-spi",
.data = (void *)&exynos7_spi_port_config,
},
{ .compatible = "samsung,exynos5433-spi",
.data = (void *)&exynos5433_spi_port_config,
},
{ },
};
MODULE_DEVICE_TABLE(of, s3c64xx_spi_dt_match);
static struct platform_driver s3c64xx_spi_driver = {
.driver = {
.name = "s3c64xx-spi",
.pm = &s3c64xx_spi_pm,
.of_match_table = of_match_ptr(s3c64xx_spi_dt_match),
},
.probe = s3c64xx_spi_probe,
.remove = s3c64xx_spi_remove,
.id_table = s3c64xx_spi_driver_ids,
};
MODULE_ALIAS("platform:s3c64xx-spi");
module_platform_driver(s3c64xx_spi_driver);
MODULE_AUTHOR("Jaswinder Singh <jassi.brar@samsung.com>");
MODULE_DESCRIPTION("S3C64XX SPI Controller Driver");
MODULE_LICENSE("GPL");