linux/drivers/net/can/Kconfig
Marc Kleine-Budde 68f4015274 at91_can: add driver for Atmel's CAN controller on AT91SAM9263
This patch add the driver for the SoC CAN controller in Atmel's
AT91SAM9263.

Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2009-09-22 14:46:57 -07:00

109 lines
3.5 KiB
Plaintext

menu "CAN Device Drivers"
depends on CAN
config CAN_VCAN
tristate "Virtual Local CAN Interface (vcan)"
depends on CAN
default N
---help---
Similar to the network loopback devices, vcan offers a
virtual local CAN interface.
This driver can also be built as a module. If so, the module
will be called vcan.
config CAN_DEV
tristate "Platform CAN drivers with Netlink support"
depends on CAN
default Y
---help---
Enables the common framework for platform CAN drivers with Netlink
support. This is the standard library for CAN drivers.
If unsure, say Y.
config CAN_CALC_BITTIMING
bool "CAN bit-timing calculation"
depends on CAN_DEV
default Y
---help---
If enabled, CAN bit-timing parameters will be calculated for the
bit-rate specified via Netlink argument "bitrate" when the device
get started. This works fine for the most common CAN controllers
with standard bit-rates but may fail for exotic bit-rates or CAN
source clock frequencies. Disabling saves some space, but then the
bit-timing parameters must be specified directly using the Netlink
arguments "tq", "prop_seg", "phase_seg1", "phase_seg2" and "sjw".
If unsure, say Y.
config CAN_SJA1000
depends on CAN_DEV && HAS_IOMEM
tristate "Philips SJA1000"
---help---
Driver for the SJA1000 CAN controllers from Philips or NXP
config CAN_SJA1000_ISA
depends on CAN_SJA1000 && ISA
tristate "ISA Bus based legacy SJA1000 driver"
---help---
This driver adds legacy support for SJA1000 chips connected to
the ISA bus using I/O port, memory mapped or indirect access.
config CAN_SJA1000_PLATFORM
depends on CAN_SJA1000
tristate "Generic Platform Bus based SJA1000 driver"
---help---
This driver adds support for the SJA1000 chips connected to
the "platform bus" (Linux abstraction for directly to the
processor attached devices). Which can be found on various
boards from Phytec (http://www.phytec.de) like the PCM027,
PCM038.
config CAN_SJA1000_OF_PLATFORM
depends on CAN_SJA1000 && PPC_OF
tristate "Generic OF Platform Bus based SJA1000 driver"
---help---
This driver adds support for the SJA1000 chips connected to
the OpenFirmware "platform bus" found on embedded systems with
OpenFirmware bindings, e.g. if you have a PowerPC based system
you may want to enable this option.
config CAN_EMS_PCI
tristate "EMS CPC-PCI, CPC-PCIe and CPC-104P Card"
depends on PCI && CAN_SJA1000
---help---
This driver is for the one, two or four channel CPC-PCI,
CPC-PCIe and CPC-104P cards from EMS Dr. Thomas Wuensche
(http://www.ems-wuensche.de).
config CAN_EMS_USB
tristate "EMS CPC-USB/ARM7 CAN/USB interface"
depends on USB && CAN_DEV
---help---
This driver is for the one channel CPC-USB/ARM7 CAN/USB interface
from from EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
config CAN_KVASER_PCI
tristate "Kvaser PCIcanx and Kvaser PCIcan PCI Cards"
depends on PCI && CAN_SJA1000
---help---
This driver is for the the PCIcanx and PCIcan cards (1, 2 or
4 channel) from Kvaser (http://www.kvaser.com).
config CAN_AT91
tristate "Atmel AT91 onchip CAN controller"
depends on CAN && CAN_DEV && ARCH_AT91SAM9263
---help---
This is a driver for the SoC CAN controller in Atmel's AT91SAM9263.
config CAN_DEBUG_DEVICES
bool "CAN devices debugging messages"
depends on CAN
default N
---help---
Say Y here if you want the CAN device drivers to produce a bunch of
debug messages to the system log. Select this if you are having
a problem with CAN support and want to see more of what is going
on.
endmenu