linux/arch/arm/boot/dts/armada-xp-openblocks-ax3-4.dts
Ezequiel Garcia 14fd8ed0a7 ARM: mvebu: Relocate Armada 370/XP PCIe device tree nodes
Now that mbus has been added to the device tree, it's possible to
move the PCIe nodes out of internal registers, placing it directly
below the mbus. This is a more accurate representation of the
hardware.

Moving the PCIe nodes, we now need to introduce an extra cell to
encode the window target ID and attribute. Since this depends on
the PCIe port, we split the ranges translation entries, to correspond
to each MBus window.

Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
2013-08-06 14:11:27 +00:00

191 lines
3.5 KiB
Plaintext

/*
* Device Tree file for OpenBlocks AX3-4 board
*
* Copyright (C) 2012 Marvell
*
* Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
*
* This file is licensed under the terms of the GNU General Public
* License version 2. This program is licensed "as is" without any
* warranty of any kind, whether express or implied.
*/
/dts-v1/;
#include "armada-xp-mv78260.dtsi"
/ {
model = "PlatHome OpenBlocks AX3-4 board";
compatible = "plathome,openblocks-ax3-4", "marvell,armadaxp-mv78260", "marvell,armadaxp", "marvell,armada-370-xp";
chosen {
bootargs = "console=ttyS0,115200 earlyprintk";
};
memory {
device_type = "memory";
reg = <0 0x00000000 0 0xC0000000>; /* 3 GB */
};
soc {
ranges = <MBUS_ID(0xf0, 0x01) 0 0 0xd0000000 0x100000
MBUS_ID(0x01, 0x1d) 0 0 0xfff00000 0x100000
MBUS_ID(0x01, 0x2f) 0 0 0xf0000000 0x8000000>;
devbus-bootcs {
status = "okay";
/* Device Bus parameters are required */
/* Read parameters */
devbus,bus-width = <8>;
devbus,turn-off-ps = <60000>;
devbus,badr-skew-ps = <0>;
devbus,acc-first-ps = <124000>;
devbus,acc-next-ps = <248000>;
devbus,rd-setup-ps = <0>;
devbus,rd-hold-ps = <0>;
/* Write parameters */
devbus,sync-enable = <0>;
devbus,wr-high-ps = <60000>;
devbus,wr-low-ps = <60000>;
devbus,ale-wr-ps = <60000>;
/* NOR 128 MiB */
nor@0 {
compatible = "cfi-flash";
reg = <0 0x8000000>;
bank-width = <2>;
};
};
pcie-controller {
status = "okay";
/* Internal mini-PCIe connector */
pcie@1,0 {
/* Port 0, Lane 0 */
status = "okay";
};
};
internal-regs {
serial@12000 {
clock-frequency = <250000000>;
status = "okay";
};
serial@12100 {
clock-frequency = <250000000>;
status = "okay";
};
pinctrl {
led_pins: led-pins-0 {
marvell,pins = "mpp49", "mpp51", "mpp53";
marvell,function = "gpio";
};
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins>;
red_led {
label = "red_led";
gpios = <&gpio1 17 1>;
default-state = "off";
};
yellow_led {
label = "yellow_led";
gpios = <&gpio1 19 1>;
default-state = "off";
};
green_led {
label = "green_led";
gpios = <&gpio1 21 1>;
default-state = "off";
linux,default-trigger = "heartbeat";
};
};
gpio_keys {
compatible = "gpio-keys";
#address-cells = <1>;
#size-cells = <0>;
button@1 {
label = "Init Button";
linux,code = <116>;
gpios = <&gpio1 28 0>;
};
};
mdio {
phy0: ethernet-phy@0 {
reg = <0>;
};
phy1: ethernet-phy@1 {
reg = <1>;
};
phy2: ethernet-phy@2 {
reg = <2>;
};
phy3: ethernet-phy@3 {
reg = <3>;
};
};
ethernet@70000 {
status = "okay";
phy = <&phy0>;
phy-mode = "sgmii";
};
ethernet@74000 {
status = "okay";
phy = <&phy1>;
phy-mode = "sgmii";
};
ethernet@30000 {
status = "okay";
phy = <&phy2>;
phy-mode = "sgmii";
};
ethernet@34000 {
status = "okay";
phy = <&phy3>;
phy-mode = "sgmii";
};
i2c@11000 {
status = "okay";
clock-frequency = <400000>;
};
i2c@11100 {
status = "okay";
clock-frequency = <400000>;
s35390a: s35390a@30 {
compatible = "s35390a";
reg = <0x30>;
};
};
sata@a0000 {
nr-ports = <2>;
status = "okay";
};
/* Front side USB 0 */
usb@50000 {
status = "okay";
};
/* Front side USB 1 */
usb@51000 {
status = "okay";
};
};
};
};