linux/drivers/usb/dwc3/Kconfig
Manu Gautam a4333c3a6b usb: dwc3: Add Qualcomm DWC3 glue driver
DWC3 controller on Qualcomm SOCs has a Qscratch wrapper.
Some of its uses are described below resulting in need to
have a separate glue driver instead of using dwc3-of-simple:
 - It exposes register interface to override vbus-override
   and lane0-pwr-present signals going to hardware. These
   must be updated in peripheral mode for DWC3 if vbus lines
   are not connected to hardware block. Otherwise RX termination
   in SS mode or DP pull-up is not applied by device controller.
 - pwr_events_irq_stat support to check if USB2 PHY is in L2 state
   before glue driver proceeds with suspend.
 - Support for wakeup interrupts lines that are asserted whenever
   there is any wakeup event on USB3 or USB2 bus.
 - Support to replace pip3 clock going to DWC3 with utmi clock
   for hardware configuration where SSPHY is not used with DWC3.

Signed-off-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
2018-05-15 10:20:13 +03:00

122 lines
3.5 KiB
Plaintext

config USB_DWC3
tristate "DesignWare USB3 DRD Core Support"
depends on (USB || USB_GADGET) && HAS_DMA
select USB_XHCI_PLATFORM if USB_XHCI_HCD
help
Say Y or M here if your system has a Dual Role SuperSpeed
USB controller based on the DesignWare USB3 IP Core.
If you choose to build this driver is a dynamically linked
module, the module will be called dwc3.ko.
if USB_DWC3
config USB_DWC3_ULPI
bool "Register ULPI PHY Interface"
depends on USB_ULPI_BUS=y || USB_ULPI_BUS=USB_DWC3
help
Select this if you have ULPI type PHY attached to your DWC3
controller.
choice
bool "DWC3 Mode Selection"
default USB_DWC3_DUAL_ROLE if (USB && USB_GADGET)
default USB_DWC3_HOST if (USB && !USB_GADGET)
default USB_DWC3_GADGET if (!USB && USB_GADGET)
config USB_DWC3_HOST
bool "Host only mode"
depends on USB=y || USB=USB_DWC3
help
Select this when you want to use DWC3 in host mode only,
thereby the gadget feature will be regressed.
config USB_DWC3_GADGET
bool "Gadget only mode"
depends on USB_GADGET=y || USB_GADGET=USB_DWC3
help
Select this when you want to use DWC3 in gadget mode only,
thereby the host feature will be regressed.
config USB_DWC3_DUAL_ROLE
bool "Dual Role mode"
depends on ((USB=y || USB=USB_DWC3) && (USB_GADGET=y || USB_GADGET=USB_DWC3))
depends on (EXTCON=y || EXTCON=USB_DWC3)
help
This is the default mode of working of DWC3 controller where
both host and gadget features are enabled.
endchoice
comment "Platform Glue Driver Support"
config USB_DWC3_OMAP
tristate "Texas Instruments OMAP5 and similar Platforms"
depends on EXTCON && (ARCH_OMAP2PLUS || COMPILE_TEST)
depends on OF
default USB_DWC3
help
Some platforms from Texas Instruments like OMAP5, DRA7xxx and
AM437x use this IP for USB2/3 functionality.
Say 'Y' or 'M' here if you have one such device
config USB_DWC3_EXYNOS
tristate "Samsung Exynos Platform"
depends on (ARCH_EXYNOS || COMPILE_TEST) && OF
default USB_DWC3
help
Recent Exynos5 SoCs ship with one DesignWare Core USB3 IP inside,
say 'Y' or 'M' if you have one such device.
config USB_DWC3_PCI
tristate "PCIe-based Platforms"
depends on USB_PCI && ACPI
default USB_DWC3
help
If you're using the DesignWare Core IP with a PCIe, please say
'Y' or 'M' here.
One such PCIe-based platform is Synopsys' PCIe HAPS model of
this IP.
config USB_DWC3_KEYSTONE
tristate "Texas Instruments Keystone2 Platforms"
depends on ARCH_KEYSTONE || COMPILE_TEST
default USB_DWC3
help
Support of USB2/3 functionality in TI Keystone2 platforms.
Say 'Y' or 'M' here if you have one such device
config USB_DWC3_OF_SIMPLE
tristate "Generic OF Simple Glue Layer"
depends on OF && COMMON_CLK
default USB_DWC3
help
Support USB2/3 functionality in simple SoC integrations.
Currently supports Xilinx and Qualcomm DWC USB3 IP.
Say 'Y' or 'M' if you have one such device.
config USB_DWC3_ST
tristate "STMicroelectronics Platforms"
depends on (ARCH_STI || COMPILE_TEST) && OF
default USB_DWC3
help
STMicroelectronics SoCs with one DesignWare Core USB3 IP
inside (i.e. STiH407).
Say 'Y' or 'M' if you have one such device.
config USB_DWC3_QCOM
tristate "Qualcomm Platform"
depends on ARCH_QCOM || COMPILE_TEST
depends on OF
default USB_DWC3
help
Some Qualcomm SoCs use DesignWare Core IP for USB2/3
functionality.
This driver also handles Qscratch wrapper which is needed
for peripheral mode support.
Say 'Y' or 'M' if you have one such device.
endif