linux/arch/arm/boot/dts/imx28-duckbill.dts
Thomas Gleixner fcaf20360a treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 159
Based on 1 normalized pattern(s):

  the code contained herein is licensed under the gnu general public
  license you may obtain a copy of the gnu general public license
  version 2 or later at the following locations http www opensource
  org licenses gpl license html http www gnu org copyleft gpl html

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 161 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.383790741@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-05-30 11:26:37 -07:00

148 lines
3.1 KiB
Plaintext

// SPDX-License-Identifier: GPL-2.0-or-later
/*
* Copyright (C) 2013-2014,2016 Michael Heimpold <mhei@heimpold.de>
* Copyright (C) 2015-2017 I2SE GmbH <info@i2se.com>
*/
/dts-v1/;
#include <dt-bindings/gpio/gpio.h>
#include "imx28.dtsi"
/ {
model = "I2SE Duckbill";
compatible = "i2se,duckbill", "fsl,imx28";
memory@40000000 {
device_type = "memory";
reg = <0x40000000 0x08000000>;
};
apb@80000000 {
apbh@80000000 {
ssp0: spi@80010000 {
compatible = "fsl,imx28-mmc";
pinctrl-names = "default";
pinctrl-0 = <&mmc0_4bit_pins_a
&mmc0_cd_cfg &mmc0_sck_cfg>;
bus-width = <4>;
vmmc-supply = <&reg_3p3v>;
status = "okay";
};
ssp2: spi@80014000 {
compatible = "fsl,imx28-spi";
pinctrl-names = "default";
pinctrl-0 = <&spi2_pins_a>;
status = "okay";
};
pinctrl@80018000 {
pinctrl-names = "default";
pinctrl-0 = <&hog_pins_a>;
hog_pins_a: hog@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_LCD_D17__GPIO_1_17 /* Revision detection */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
mac0_phy_reset_pin: mac0-phy-reset@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_SSP0_DATA7__GPIO_2_7 /* PHY Reset */
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
led_pins: leds@0 {
reg = <0>;
fsl,pinmux-ids = <
MX28_PAD_AUART1_RX__GPIO_3_4
MX28_PAD_AUART1_TX__GPIO_3_5
>;
fsl,drive-strength = <MXS_DRIVE_4mA>;
fsl,voltage = <MXS_VOLTAGE_HIGH>;
fsl,pull-up = <MXS_PULL_DISABLE>;
};
};
};
apbx@80040000 {
lradc@80050000 {
status = "okay";
};
i2c0: i2c@80058000 {
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins_a>;
status = "okay";
};
auart0: serial@8006a000 {
pinctrl-names = "default";
pinctrl-0 = <&auart0_2pins_a>;
status = "okay";
};
duart: serial@80074000 {
pinctrl-names = "default";
pinctrl-0 = <&duart_pins_a>;
status = "okay";
};
usbphy0: usbphy@8007c000 {
status = "okay";
};
};
};
ahb@80080000 {
usb0: usb@80080000 {
status = "okay";
dr_mode = "peripheral";
};
mac0: ethernet@800f0000 {
phy-mode = "rmii";
pinctrl-names = "default";
pinctrl-0 = <&mac0_pins_a>, <&mac0_phy_reset_pin>;
phy-supply = <&reg_3p3v>;
phy-reset-gpios = <&gpio2 7 GPIO_ACTIVE_LOW>;
phy-reset-duration = <25>;
status = "okay";
};
};
reg_3p3v: regulator-3p3v {
compatible = "regulator-fixed";
regulator-name = "3P3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-always-on;
};
leds {
compatible = "gpio-leds";
pinctrl-names = "default";
pinctrl-0 = <&led_pins>;
status-red {
label = "duckbill:red:status";
gpios = <&gpio3 4 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "default-on";
};
status-green {
label = "duckbill:green:status";
gpios = <&gpio3 5 GPIO_ACTIVE_HIGH>;
linux,default-trigger = "heartbeat";
};
};
};