linux/drivers/scsi/mpt3sas/mpt3sas_transport.c
Sreekanth Reddy 5b061980e3 scsi: mpt3sas: Optimize mpt3sas driver logging
This improves mpt3sas driver default debug information collection and
allows for a higher percentage of issues being able to be resolved with a
first-time data capture.  However, this improvement to balance the amount
of debug data captured with the performance of driver.

Enabled below print messages with out affecting the IO performance,

1. When task abort TM is received then print IO commands's timeout value
   and how much time this command has been outstanding.

2. Whenever hard reset occurs then print from where this hard reset has
   been issued.

3. Failure message should be displayed for failure scenarios without any
   logging level.

4. Added a print after driver successfully register or unregistered a
   target drive with the SML. This print will be useful for debugging the
   issue where the drive addition or deletion is hanging at SML.

5. During driver load time print request, reply, sense and config page
   pool's information such as its address, length and size. Also printed
   sg_tablesize information.

Link: https://lore.kernel.org/r/20191226111333.26131-8-sreekanth.reddy@broadcom.com
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
2020-01-02 22:23:17 -05:00

1980 lines
58 KiB
C

/*
* SAS Transport Layer for MPT (Message Passing Technology) based controllers
*
* This code is based on drivers/scsi/mpt3sas/mpt3sas_transport.c
* Copyright (C) 2012-2014 LSI Corporation
* Copyright (C) 2013-2014 Avago Technologies
* (mailto: MPT-FusionLinux.pdl@avagotech.com)
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version 2
* of the License, or (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* NO WARRANTY
* THE PROGRAM IS PROVIDED ON AN "AS IS" BASIS, WITHOUT WARRANTIES OR
* CONDITIONS OF ANY KIND, EITHER EXPRESS OR IMPLIED INCLUDING, WITHOUT
* LIMITATION, ANY WARRANTIES OR CONDITIONS OF TITLE, NON-INFRINGEMENT,
* MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Each Recipient is
* solely responsible for determining the appropriateness of using and
* distributing the Program and assumes all risks associated with its
* exercise of rights under this Agreement, including but not limited to
* the risks and costs of program errors, damage to or loss of data,
* programs or equipment, and unavailability or interruption of operations.
* DISCLAIMER OF LIABILITY
* NEITHER RECIPIENT NOR ANY CONTRIBUTORS SHALL HAVE ANY LIABILITY FOR ANY
* DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
* DAMAGES (INCLUDING WITHOUT LIMITATION LOST PROFITS), HOWEVER CAUSED AND
* ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR
* TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE
* USE OR DISTRIBUTION OF THE PROGRAM OR THE EXERCISE OF ANY RIGHTS GRANTED
* HEREUNDER, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
* USA.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/errno.h>
#include <linux/sched.h>
#include <linux/workqueue.h>
#include <linux/delay.h>
#include <linux/pci.h>
#include <scsi/scsi.h>
#include <scsi/scsi_cmnd.h>
#include <scsi/scsi_device.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_transport_sas.h>
#include <scsi/scsi_dbg.h>
#include "mpt3sas_base.h"
/**
* _transport_sas_node_find_by_sas_address - sas node search
* @ioc: per adapter object
* @sas_address: sas address of expander or sas host
* Context: Calling function should acquire ioc->sas_node_lock.
*
* Search for either hba phys or expander device based on handle, then returns
* the sas_node object.
*/
static struct _sas_node *
_transport_sas_node_find_by_sas_address(struct MPT3SAS_ADAPTER *ioc,
u64 sas_address)
{
if (ioc->sas_hba.sas_address == sas_address)
return &ioc->sas_hba;
else
return mpt3sas_scsih_expander_find_by_sas_address(ioc,
sas_address);
}
/**
* _transport_convert_phy_link_rate -
* @link_rate: link rate returned from mpt firmware
*
* Convert link_rate from mpi fusion into sas_transport form.
*/
static enum sas_linkrate
_transport_convert_phy_link_rate(u8 link_rate)
{
enum sas_linkrate rc;
switch (link_rate) {
case MPI2_SAS_NEG_LINK_RATE_1_5:
rc = SAS_LINK_RATE_1_5_GBPS;
break;
case MPI2_SAS_NEG_LINK_RATE_3_0:
rc = SAS_LINK_RATE_3_0_GBPS;
break;
case MPI2_SAS_NEG_LINK_RATE_6_0:
rc = SAS_LINK_RATE_6_0_GBPS;
break;
case MPI25_SAS_NEG_LINK_RATE_12_0:
rc = SAS_LINK_RATE_12_0_GBPS;
break;
case MPI2_SAS_NEG_LINK_RATE_PHY_DISABLED:
rc = SAS_PHY_DISABLED;
break;
case MPI2_SAS_NEG_LINK_RATE_NEGOTIATION_FAILED:
rc = SAS_LINK_RATE_FAILED;
break;
case MPI2_SAS_NEG_LINK_RATE_PORT_SELECTOR:
rc = SAS_SATA_PORT_SELECTOR;
break;
case MPI2_SAS_NEG_LINK_RATE_SMP_RESET_IN_PROGRESS:
rc = SAS_PHY_RESET_IN_PROGRESS;
break;
default:
case MPI2_SAS_NEG_LINK_RATE_SATA_OOB_COMPLETE:
case MPI2_SAS_NEG_LINK_RATE_UNKNOWN_LINK_RATE:
rc = SAS_LINK_RATE_UNKNOWN;
break;
}
return rc;
}
/**
* _transport_set_identify - set identify for phys and end devices
* @ioc: per adapter object
* @handle: device handle
* @identify: sas identify info
*
* Populates sas identify info.
*
* Return: 0 for success, non-zero for failure.
*/
static int
_transport_set_identify(struct MPT3SAS_ADAPTER *ioc, u16 handle,
struct sas_identify *identify)
{
Mpi2SasDevicePage0_t sas_device_pg0;
Mpi2ConfigReply_t mpi_reply;
u32 device_info;
u32 ioc_status;
if (ioc->shost_recovery || ioc->pci_error_recovery) {
ioc_info(ioc, "%s: host reset in progress!\n", __func__);
return -EFAULT;
}
if ((mpt3sas_config_get_sas_device_pg0(ioc, &mpi_reply, &sas_device_pg0,
MPI2_SAS_DEVICE_PGAD_FORM_HANDLE, handle))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
return -ENXIO;
}
ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
MPI2_IOCSTATUS_MASK;
if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
ioc_err(ioc, "handle(0x%04x), ioc_status(0x%04x) failure at %s:%d/%s()!\n",
handle, ioc_status, __FILE__, __LINE__, __func__);
return -EIO;
}
memset(identify, 0, sizeof(struct sas_identify));
device_info = le32_to_cpu(sas_device_pg0.DeviceInfo);
/* sas_address */
identify->sas_address = le64_to_cpu(sas_device_pg0.SASAddress);
/* phy number of the parent device this device is linked to */
identify->phy_identifier = sas_device_pg0.PhyNum;
/* device_type */
switch (device_info & MPI2_SAS_DEVICE_INFO_MASK_DEVICE_TYPE) {
case MPI2_SAS_DEVICE_INFO_NO_DEVICE:
identify->device_type = SAS_PHY_UNUSED;
break;
case MPI2_SAS_DEVICE_INFO_END_DEVICE:
identify->device_type = SAS_END_DEVICE;
break;
case MPI2_SAS_DEVICE_INFO_EDGE_EXPANDER:
identify->device_type = SAS_EDGE_EXPANDER_DEVICE;
break;
case MPI2_SAS_DEVICE_INFO_FANOUT_EXPANDER:
identify->device_type = SAS_FANOUT_EXPANDER_DEVICE;
break;
}
/* initiator_port_protocols */
if (device_info & MPI2_SAS_DEVICE_INFO_SSP_INITIATOR)
identify->initiator_port_protocols |= SAS_PROTOCOL_SSP;
if (device_info & MPI2_SAS_DEVICE_INFO_STP_INITIATOR)
identify->initiator_port_protocols |= SAS_PROTOCOL_STP;
if (device_info & MPI2_SAS_DEVICE_INFO_SMP_INITIATOR)
identify->initiator_port_protocols |= SAS_PROTOCOL_SMP;
if (device_info & MPI2_SAS_DEVICE_INFO_SATA_HOST)
identify->initiator_port_protocols |= SAS_PROTOCOL_SATA;
/* target_port_protocols */
if (device_info & MPI2_SAS_DEVICE_INFO_SSP_TARGET)
identify->target_port_protocols |= SAS_PROTOCOL_SSP;
if (device_info & MPI2_SAS_DEVICE_INFO_STP_TARGET)
identify->target_port_protocols |= SAS_PROTOCOL_STP;
if (device_info & MPI2_SAS_DEVICE_INFO_SMP_TARGET)
identify->target_port_protocols |= SAS_PROTOCOL_SMP;
if (device_info & MPI2_SAS_DEVICE_INFO_SATA_DEVICE)
identify->target_port_protocols |= SAS_PROTOCOL_SATA;
return 0;
}
/**
* mpt3sas_transport_done - internal transport layer callback handler.
* @ioc: per adapter object
* @smid: system request message index
* @msix_index: MSIX table index supplied by the OS
* @reply: reply message frame(lower 32bit addr)
*
* Callback handler when sending internal generated transport cmds.
* The callback index passed is `ioc->transport_cb_idx`
*
* Return: 1 meaning mf should be freed from _base_interrupt
* 0 means the mf is freed from this function.
*/
u8
mpt3sas_transport_done(struct MPT3SAS_ADAPTER *ioc, u16 smid, u8 msix_index,
u32 reply)
{
MPI2DefaultReply_t *mpi_reply;
mpi_reply = mpt3sas_base_get_reply_virt_addr(ioc, reply);
if (ioc->transport_cmds.status == MPT3_CMD_NOT_USED)
return 1;
if (ioc->transport_cmds.smid != smid)
return 1;
ioc->transport_cmds.status |= MPT3_CMD_COMPLETE;
if (mpi_reply) {
memcpy(ioc->transport_cmds.reply, mpi_reply,
mpi_reply->MsgLength*4);
ioc->transport_cmds.status |= MPT3_CMD_REPLY_VALID;
}
ioc->transport_cmds.status &= ~MPT3_CMD_PENDING;
complete(&ioc->transport_cmds.done);
return 1;
}
/* report manufacture request structure */
struct rep_manu_request {
u8 smp_frame_type;
u8 function;
u8 reserved;
u8 request_length;
};
/* report manufacture reply structure */
struct rep_manu_reply {
u8 smp_frame_type; /* 0x41 */
u8 function; /* 0x01 */
u8 function_result;
u8 response_length;
u16 expander_change_count;
u8 reserved0[2];
u8 sas_format;
u8 reserved2[3];
u8 vendor_id[SAS_EXPANDER_VENDOR_ID_LEN];
u8 product_id[SAS_EXPANDER_PRODUCT_ID_LEN];
u8 product_rev[SAS_EXPANDER_PRODUCT_REV_LEN];
u8 component_vendor_id[SAS_EXPANDER_COMPONENT_VENDOR_ID_LEN];
u16 component_id;
u8 component_revision_id;
u8 reserved3;
u8 vendor_specific[8];
};
/**
* transport_expander_report_manufacture - obtain SMP report_manufacture
* @ioc: per adapter object
* @sas_address: expander sas address
* @edev: the sas_expander_device object
*
* Fills in the sas_expander_device object when SMP port is created.
*
* Return: 0 for success, non-zero for failure.
*/
static int
_transport_expander_report_manufacture(struct MPT3SAS_ADAPTER *ioc,
u64 sas_address, struct sas_expander_device *edev)
{
Mpi2SmpPassthroughRequest_t *mpi_request;
Mpi2SmpPassthroughReply_t *mpi_reply;
struct rep_manu_reply *manufacture_reply;
struct rep_manu_request *manufacture_request;
int rc;
u16 smid;
void *psge;
u8 issue_reset = 0;
void *data_out = NULL;
dma_addr_t data_out_dma;
dma_addr_t data_in_dma;
size_t data_in_sz;
size_t data_out_sz;
if (ioc->shost_recovery || ioc->pci_error_recovery) {
ioc_info(ioc, "%s: host reset in progress!\n", __func__);
return -EFAULT;
}
mutex_lock(&ioc->transport_cmds.mutex);
if (ioc->transport_cmds.status != MPT3_CMD_NOT_USED) {
ioc_err(ioc, "%s: transport_cmds in use\n", __func__);
rc = -EAGAIN;
goto out;
}
ioc->transport_cmds.status = MPT3_CMD_PENDING;
rc = mpt3sas_wait_for_ioc(ioc, IOC_OPERATIONAL_WAIT_COUNT);
if (rc)
goto out;
smid = mpt3sas_base_get_smid(ioc, ioc->transport_cb_idx);
if (!smid) {
ioc_err(ioc, "%s: failed obtaining a smid\n", __func__);
rc = -EAGAIN;
goto out;
}
rc = 0;
mpi_request = mpt3sas_base_get_msg_frame(ioc, smid);
ioc->transport_cmds.smid = smid;
data_out_sz = sizeof(struct rep_manu_request);
data_in_sz = sizeof(struct rep_manu_reply);
data_out = dma_alloc_coherent(&ioc->pdev->dev, data_out_sz + data_in_sz,
&data_out_dma, GFP_KERNEL);
if (!data_out) {
pr_err("failure at %s:%d/%s()!\n", __FILE__,
__LINE__, __func__);
rc = -ENOMEM;
mpt3sas_base_free_smid(ioc, smid);
goto out;
}
data_in_dma = data_out_dma + sizeof(struct rep_manu_request);
manufacture_request = data_out;
manufacture_request->smp_frame_type = 0x40;
manufacture_request->function = 1;
manufacture_request->reserved = 0;
manufacture_request->request_length = 0;
memset(mpi_request, 0, sizeof(Mpi2SmpPassthroughRequest_t));
mpi_request->Function = MPI2_FUNCTION_SMP_PASSTHROUGH;
mpi_request->PhysicalPort = 0xFF;
mpi_request->SASAddress = cpu_to_le64(sas_address);
mpi_request->RequestDataLength = cpu_to_le16(data_out_sz);
psge = &mpi_request->SGL;
ioc->build_sg(ioc, psge, data_out_dma, data_out_sz, data_in_dma,
data_in_sz);
dtransportprintk(ioc,
ioc_info(ioc, "report_manufacture - send to sas_addr(0x%016llx)\n",
(u64)sas_address));
init_completion(&ioc->transport_cmds.done);
ioc->put_smid_default(ioc, smid);
wait_for_completion_timeout(&ioc->transport_cmds.done, 10*HZ);
if (!(ioc->transport_cmds.status & MPT3_CMD_COMPLETE)) {
ioc_err(ioc, "%s: timeout\n", __func__);
_debug_dump_mf(mpi_request,
sizeof(Mpi2SmpPassthroughRequest_t)/4);
if (!(ioc->transport_cmds.status & MPT3_CMD_RESET))
issue_reset = 1;
goto issue_host_reset;
}
dtransportprintk(ioc, ioc_info(ioc, "report_manufacture - complete\n"));
if (ioc->transport_cmds.status & MPT3_CMD_REPLY_VALID) {
u8 *tmp;
mpi_reply = ioc->transport_cmds.reply;
dtransportprintk(ioc,
ioc_info(ioc, "report_manufacture - reply data transfer size(%d)\n",
le16_to_cpu(mpi_reply->ResponseDataLength)));
if (le16_to_cpu(mpi_reply->ResponseDataLength) !=
sizeof(struct rep_manu_reply))
goto out;
manufacture_reply = data_out + sizeof(struct rep_manu_request);
strncpy(edev->vendor_id, manufacture_reply->vendor_id,
SAS_EXPANDER_VENDOR_ID_LEN);
strncpy(edev->product_id, manufacture_reply->product_id,
SAS_EXPANDER_PRODUCT_ID_LEN);
strncpy(edev->product_rev, manufacture_reply->product_rev,
SAS_EXPANDER_PRODUCT_REV_LEN);
edev->level = manufacture_reply->sas_format & 1;
if (edev->level) {
strncpy(edev->component_vendor_id,
manufacture_reply->component_vendor_id,
SAS_EXPANDER_COMPONENT_VENDOR_ID_LEN);
tmp = (u8 *)&manufacture_reply->component_id;
edev->component_id = tmp[0] << 8 | tmp[1];
edev->component_revision_id =
manufacture_reply->component_revision_id;
}
} else
dtransportprintk(ioc,
ioc_info(ioc, "report_manufacture - no reply\n"));
issue_host_reset:
if (issue_reset)
mpt3sas_base_hard_reset_handler(ioc, FORCE_BIG_HAMMER);
out:
ioc->transport_cmds.status = MPT3_CMD_NOT_USED;
if (data_out)
dma_free_coherent(&ioc->pdev->dev, data_out_sz + data_in_sz,
data_out, data_out_dma);
mutex_unlock(&ioc->transport_cmds.mutex);
return rc;
}
/**
* _transport_delete_port - helper function to removing a port
* @ioc: per adapter object
* @mpt3sas_port: mpt3sas per port object
*/
static void
_transport_delete_port(struct MPT3SAS_ADAPTER *ioc,
struct _sas_port *mpt3sas_port)
{
u64 sas_address = mpt3sas_port->remote_identify.sas_address;
enum sas_device_type device_type =
mpt3sas_port->remote_identify.device_type;
dev_printk(KERN_INFO, &mpt3sas_port->port->dev,
"remove: sas_addr(0x%016llx)\n",
(unsigned long long) sas_address);
ioc->logging_level |= MPT_DEBUG_TRANSPORT;
if (device_type == SAS_END_DEVICE)
mpt3sas_device_remove_by_sas_address(ioc, sas_address);
else if (device_type == SAS_EDGE_EXPANDER_DEVICE ||
device_type == SAS_FANOUT_EXPANDER_DEVICE)
mpt3sas_expander_remove(ioc, sas_address);
ioc->logging_level &= ~MPT_DEBUG_TRANSPORT;
}
/**
* _transport_delete_phy - helper function to removing single phy from port
* @ioc: per adapter object
* @mpt3sas_port: mpt3sas per port object
* @mpt3sas_phy: mpt3sas per phy object
*/
static void
_transport_delete_phy(struct MPT3SAS_ADAPTER *ioc,
struct _sas_port *mpt3sas_port, struct _sas_phy *mpt3sas_phy)
{
u64 sas_address = mpt3sas_port->remote_identify.sas_address;
dev_printk(KERN_INFO, &mpt3sas_phy->phy->dev,
"remove: sas_addr(0x%016llx), phy(%d)\n",
(unsigned long long) sas_address, mpt3sas_phy->phy_id);
list_del(&mpt3sas_phy->port_siblings);
mpt3sas_port->num_phys--;
sas_port_delete_phy(mpt3sas_port->port, mpt3sas_phy->phy);
mpt3sas_phy->phy_belongs_to_port = 0;
}
/**
* _transport_add_phy - helper function to adding single phy to port
* @ioc: per adapter object
* @mpt3sas_port: mpt3sas per port object
* @mpt3sas_phy: mpt3sas per phy object
*/
static void
_transport_add_phy(struct MPT3SAS_ADAPTER *ioc, struct _sas_port *mpt3sas_port,
struct _sas_phy *mpt3sas_phy)
{
u64 sas_address = mpt3sas_port->remote_identify.sas_address;
dev_printk(KERN_INFO, &mpt3sas_phy->phy->dev,
"add: sas_addr(0x%016llx), phy(%d)\n", (unsigned long long)
sas_address, mpt3sas_phy->phy_id);
list_add_tail(&mpt3sas_phy->port_siblings, &mpt3sas_port->phy_list);
mpt3sas_port->num_phys++;
sas_port_add_phy(mpt3sas_port->port, mpt3sas_phy->phy);
mpt3sas_phy->phy_belongs_to_port = 1;
}
/**
* _transport_add_phy_to_an_existing_port - adding new phy to existing port
* @ioc: per adapter object
* @sas_node: sas node object (either expander or sas host)
* @mpt3sas_phy: mpt3sas per phy object
* @sas_address: sas address of device/expander were phy needs to be added to
*/
static void
_transport_add_phy_to_an_existing_port(struct MPT3SAS_ADAPTER *ioc,
struct _sas_node *sas_node, struct _sas_phy *mpt3sas_phy,
u64 sas_address)
{
struct _sas_port *mpt3sas_port;
struct _sas_phy *phy_srch;
if (mpt3sas_phy->phy_belongs_to_port == 1)
return;
list_for_each_entry(mpt3sas_port, &sas_node->sas_port_list,
port_list) {
if (mpt3sas_port->remote_identify.sas_address !=
sas_address)
continue;
list_for_each_entry(phy_srch, &mpt3sas_port->phy_list,
port_siblings) {
if (phy_srch == mpt3sas_phy)
return;
}
_transport_add_phy(ioc, mpt3sas_port, mpt3sas_phy);
return;
}
}
/**
* _transport_del_phy_from_an_existing_port - delete phy from existing port
* @ioc: per adapter object
* @sas_node: sas node object (either expander or sas host)
* @mpt3sas_phy: mpt3sas per phy object
*/
static void
_transport_del_phy_from_an_existing_port(struct MPT3SAS_ADAPTER *ioc,
struct _sas_node *sas_node, struct _sas_phy *mpt3sas_phy)
{
struct _sas_port *mpt3sas_port, *next;
struct _sas_phy *phy_srch;
if (mpt3sas_phy->phy_belongs_to_port == 0)
return;
list_for_each_entry_safe(mpt3sas_port, next, &sas_node->sas_port_list,
port_list) {
list_for_each_entry(phy_srch, &mpt3sas_port->phy_list,
port_siblings) {
if (phy_srch != mpt3sas_phy)
continue;
if (mpt3sas_port->num_phys == 1)
_transport_delete_port(ioc, mpt3sas_port);
else
_transport_delete_phy(ioc, mpt3sas_port,
mpt3sas_phy);
return;
}
}
}
/**
* _transport_sanity_check - sanity check when adding a new port
* @ioc: per adapter object
* @sas_node: sas node object (either expander or sas host)
* @sas_address: sas address of device being added
*
* See the explanation above from _transport_delete_duplicate_port
*/
static void
_transport_sanity_check(struct MPT3SAS_ADAPTER *ioc, struct _sas_node *sas_node,
u64 sas_address)
{
int i;
for (i = 0; i < sas_node->num_phys; i++) {
if (sas_node->phy[i].remote_identify.sas_address != sas_address)
continue;
if (sas_node->phy[i].phy_belongs_to_port == 1)
_transport_del_phy_from_an_existing_port(ioc, sas_node,
&sas_node->phy[i]);
}
}
/**
* mpt3sas_transport_port_add - insert port to the list
* @ioc: per adapter object
* @handle: handle of attached device
* @sas_address: sas address of parent expander or sas host
* Context: This function will acquire ioc->sas_node_lock.
*
* Adding new port object to the sas_node->sas_port_list.
*
* Return: mpt3sas_port.
*/
struct _sas_port *
mpt3sas_transport_port_add(struct MPT3SAS_ADAPTER *ioc, u16 handle,
u64 sas_address)
{
struct _sas_phy *mpt3sas_phy, *next;
struct _sas_port *mpt3sas_port;
unsigned long flags;
struct _sas_node *sas_node;
struct sas_rphy *rphy;
struct _sas_device *sas_device = NULL;
int i;
struct sas_port *port;
mpt3sas_port = kzalloc(sizeof(struct _sas_port),
GFP_KERNEL);
if (!mpt3sas_port) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
return NULL;
}
INIT_LIST_HEAD(&mpt3sas_port->port_list);
INIT_LIST_HEAD(&mpt3sas_port->phy_list);
spin_lock_irqsave(&ioc->sas_node_lock, flags);
sas_node = _transport_sas_node_find_by_sas_address(ioc, sas_address);
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
if (!sas_node) {
ioc_err(ioc, "%s: Could not find parent sas_address(0x%016llx)!\n",
__func__, (u64)sas_address);
goto out_fail;
}
if ((_transport_set_identify(ioc, handle,
&mpt3sas_port->remote_identify))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
goto out_fail;
}
if (mpt3sas_port->remote_identify.device_type == SAS_PHY_UNUSED) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
goto out_fail;
}
_transport_sanity_check(ioc, sas_node,
mpt3sas_port->remote_identify.sas_address);
for (i = 0; i < sas_node->num_phys; i++) {
if (sas_node->phy[i].remote_identify.sas_address !=
mpt3sas_port->remote_identify.sas_address)
continue;
list_add_tail(&sas_node->phy[i].port_siblings,
&mpt3sas_port->phy_list);
mpt3sas_port->num_phys++;
}
if (!mpt3sas_port->num_phys) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
goto out_fail;
}
if (!sas_node->parent_dev) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
goto out_fail;
}
port = sas_port_alloc_num(sas_node->parent_dev);
if ((sas_port_add(port))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
goto out_fail;
}
list_for_each_entry(mpt3sas_phy, &mpt3sas_port->phy_list,
port_siblings) {
if ((ioc->logging_level & MPT_DEBUG_TRANSPORT))
dev_printk(KERN_INFO, &port->dev,
"add: handle(0x%04x), sas_addr(0x%016llx), phy(%d)\n",
handle, (unsigned long long)
mpt3sas_port->remote_identify.sas_address,
mpt3sas_phy->phy_id);
sas_port_add_phy(port, mpt3sas_phy->phy);
mpt3sas_phy->phy_belongs_to_port = 1;
}
mpt3sas_port->port = port;
if (mpt3sas_port->remote_identify.device_type == SAS_END_DEVICE)
rphy = sas_end_device_alloc(port);
else
rphy = sas_expander_alloc(port,
mpt3sas_port->remote_identify.device_type);
rphy->identify = mpt3sas_port->remote_identify;
if (mpt3sas_port->remote_identify.device_type == SAS_END_DEVICE) {
sas_device = mpt3sas_get_sdev_by_addr(ioc,
mpt3sas_port->remote_identify.sas_address);
if (!sas_device) {
dfailprintk(ioc,
ioc_info(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__));
goto out_fail;
}
sas_device->pend_sas_rphy_add = 1;
}
if ((sas_rphy_add(rphy))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
}
if (mpt3sas_port->remote_identify.device_type == SAS_END_DEVICE) {
sas_device->pend_sas_rphy_add = 0;
sas_device_put(sas_device);
}
dev_info(&rphy->dev,
"add: handle(0x%04x), sas_addr(0x%016llx)\n", handle,
(unsigned long long)mpt3sas_port->remote_identify.sas_address);
mpt3sas_port->rphy = rphy;
spin_lock_irqsave(&ioc->sas_node_lock, flags);
list_add_tail(&mpt3sas_port->port_list, &sas_node->sas_port_list);
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
/* fill in report manufacture */
if (mpt3sas_port->remote_identify.device_type ==
MPI2_SAS_DEVICE_INFO_EDGE_EXPANDER ||
mpt3sas_port->remote_identify.device_type ==
MPI2_SAS_DEVICE_INFO_FANOUT_EXPANDER)
_transport_expander_report_manufacture(ioc,
mpt3sas_port->remote_identify.sas_address,
rphy_to_expander_device(rphy));
return mpt3sas_port;
out_fail:
list_for_each_entry_safe(mpt3sas_phy, next, &mpt3sas_port->phy_list,
port_siblings)
list_del(&mpt3sas_phy->port_siblings);
kfree(mpt3sas_port);
return NULL;
}
/**
* mpt3sas_transport_port_remove - remove port from the list
* @ioc: per adapter object
* @sas_address: sas address of attached device
* @sas_address_parent: sas address of parent expander or sas host
* Context: This function will acquire ioc->sas_node_lock.
*
* Removing object and freeing associated memory from the
* ioc->sas_port_list.
*/
void
mpt3sas_transport_port_remove(struct MPT3SAS_ADAPTER *ioc, u64 sas_address,
u64 sas_address_parent)
{
int i;
unsigned long flags;
struct _sas_port *mpt3sas_port, *next;
struct _sas_node *sas_node;
u8 found = 0;
struct _sas_phy *mpt3sas_phy, *next_phy;
spin_lock_irqsave(&ioc->sas_node_lock, flags);
sas_node = _transport_sas_node_find_by_sas_address(ioc,
sas_address_parent);
if (!sas_node) {
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
return;
}
list_for_each_entry_safe(mpt3sas_port, next, &sas_node->sas_port_list,
port_list) {
if (mpt3sas_port->remote_identify.sas_address != sas_address)
continue;
found = 1;
list_del(&mpt3sas_port->port_list);
goto out;
}
out:
if (!found) {
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
return;
}
for (i = 0; i < sas_node->num_phys; i++) {
if (sas_node->phy[i].remote_identify.sas_address == sas_address)
memset(&sas_node->phy[i].remote_identify, 0 ,
sizeof(struct sas_identify));
}
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
list_for_each_entry_safe(mpt3sas_phy, next_phy,
&mpt3sas_port->phy_list, port_siblings) {
if ((ioc->logging_level & MPT_DEBUG_TRANSPORT))
dev_printk(KERN_INFO, &mpt3sas_port->port->dev,
"remove: sas_addr(0x%016llx), phy(%d)\n",
(unsigned long long)
mpt3sas_port->remote_identify.sas_address,
mpt3sas_phy->phy_id);
mpt3sas_phy->phy_belongs_to_port = 0;
if (!ioc->remove_host)
sas_port_delete_phy(mpt3sas_port->port,
mpt3sas_phy->phy);
list_del(&mpt3sas_phy->port_siblings);
}
if (!ioc->remove_host)
sas_port_delete(mpt3sas_port->port);
ioc_info(ioc, "%s: removed: sas_addr(0x%016llx)\n",
__func__, (unsigned long long)sas_address);
kfree(mpt3sas_port);
}
/**
* mpt3sas_transport_add_host_phy - report sas_host phy to transport
* @ioc: per adapter object
* @mpt3sas_phy: mpt3sas per phy object
* @phy_pg0: sas phy page 0
* @parent_dev: parent device class object
*
* Return: 0 for success, non-zero for failure.
*/
int
mpt3sas_transport_add_host_phy(struct MPT3SAS_ADAPTER *ioc, struct _sas_phy
*mpt3sas_phy, Mpi2SasPhyPage0_t phy_pg0, struct device *parent_dev)
{
struct sas_phy *phy;
int phy_index = mpt3sas_phy->phy_id;
INIT_LIST_HEAD(&mpt3sas_phy->port_siblings);
phy = sas_phy_alloc(parent_dev, phy_index);
if (!phy) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
return -1;
}
if ((_transport_set_identify(ioc, mpt3sas_phy->handle,
&mpt3sas_phy->identify))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
sas_phy_free(phy);
return -1;
}
phy->identify = mpt3sas_phy->identify;
mpt3sas_phy->attached_handle = le16_to_cpu(phy_pg0.AttachedDevHandle);
if (mpt3sas_phy->attached_handle)
_transport_set_identify(ioc, mpt3sas_phy->attached_handle,
&mpt3sas_phy->remote_identify);
phy->identify.phy_identifier = mpt3sas_phy->phy_id;
phy->negotiated_linkrate = _transport_convert_phy_link_rate(
phy_pg0.NegotiatedLinkRate & MPI2_SAS_NEG_LINK_RATE_MASK_PHYSICAL);
phy->minimum_linkrate_hw = _transport_convert_phy_link_rate(
phy_pg0.HwLinkRate & MPI2_SAS_HWRATE_MIN_RATE_MASK);
phy->maximum_linkrate_hw = _transport_convert_phy_link_rate(
phy_pg0.HwLinkRate >> 4);
phy->minimum_linkrate = _transport_convert_phy_link_rate(
phy_pg0.ProgrammedLinkRate & MPI2_SAS_PRATE_MIN_RATE_MASK);
phy->maximum_linkrate = _transport_convert_phy_link_rate(
phy_pg0.ProgrammedLinkRate >> 4);
if ((sas_phy_add(phy))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
sas_phy_free(phy);
return -1;
}
if ((ioc->logging_level & MPT_DEBUG_TRANSPORT))
dev_printk(KERN_INFO, &phy->dev,
"add: handle(0x%04x), sas_addr(0x%016llx)\n"
"\tattached_handle(0x%04x), sas_addr(0x%016llx)\n",
mpt3sas_phy->handle, (unsigned long long)
mpt3sas_phy->identify.sas_address,
mpt3sas_phy->attached_handle,
(unsigned long long)
mpt3sas_phy->remote_identify.sas_address);
mpt3sas_phy->phy = phy;
return 0;
}
/**
* mpt3sas_transport_add_expander_phy - report expander phy to transport
* @ioc: per adapter object
* @mpt3sas_phy: mpt3sas per phy object
* @expander_pg1: expander page 1
* @parent_dev: parent device class object
*
* Return: 0 for success, non-zero for failure.
*/
int
mpt3sas_transport_add_expander_phy(struct MPT3SAS_ADAPTER *ioc, struct _sas_phy
*mpt3sas_phy, Mpi2ExpanderPage1_t expander_pg1,
struct device *parent_dev)
{
struct sas_phy *phy;
int phy_index = mpt3sas_phy->phy_id;
INIT_LIST_HEAD(&mpt3sas_phy->port_siblings);
phy = sas_phy_alloc(parent_dev, phy_index);
if (!phy) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
return -1;
}
if ((_transport_set_identify(ioc, mpt3sas_phy->handle,
&mpt3sas_phy->identify))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
sas_phy_free(phy);
return -1;
}
phy->identify = mpt3sas_phy->identify;
mpt3sas_phy->attached_handle =
le16_to_cpu(expander_pg1.AttachedDevHandle);
if (mpt3sas_phy->attached_handle)
_transport_set_identify(ioc, mpt3sas_phy->attached_handle,
&mpt3sas_phy->remote_identify);
phy->identify.phy_identifier = mpt3sas_phy->phy_id;
phy->negotiated_linkrate = _transport_convert_phy_link_rate(
expander_pg1.NegotiatedLinkRate &
MPI2_SAS_NEG_LINK_RATE_MASK_PHYSICAL);
phy->minimum_linkrate_hw = _transport_convert_phy_link_rate(
expander_pg1.HwLinkRate & MPI2_SAS_HWRATE_MIN_RATE_MASK);
phy->maximum_linkrate_hw = _transport_convert_phy_link_rate(
expander_pg1.HwLinkRate >> 4);
phy->minimum_linkrate = _transport_convert_phy_link_rate(
expander_pg1.ProgrammedLinkRate & MPI2_SAS_PRATE_MIN_RATE_MASK);
phy->maximum_linkrate = _transport_convert_phy_link_rate(
expander_pg1.ProgrammedLinkRate >> 4);
if ((sas_phy_add(phy))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
sas_phy_free(phy);
return -1;
}
if ((ioc->logging_level & MPT_DEBUG_TRANSPORT))
dev_printk(KERN_INFO, &phy->dev,
"add: handle(0x%04x), sas_addr(0x%016llx)\n"
"\tattached_handle(0x%04x), sas_addr(0x%016llx)\n",
mpt3sas_phy->handle, (unsigned long long)
mpt3sas_phy->identify.sas_address,
mpt3sas_phy->attached_handle,
(unsigned long long)
mpt3sas_phy->remote_identify.sas_address);
mpt3sas_phy->phy = phy;
return 0;
}
/**
* mpt3sas_transport_update_links - refreshing phy link changes
* @ioc: per adapter object
* @sas_address: sas address of parent expander or sas host
* @handle: attached device handle
* @phy_number: phy number
* @link_rate: new link rate
*/
void
mpt3sas_transport_update_links(struct MPT3SAS_ADAPTER *ioc,
u64 sas_address, u16 handle, u8 phy_number, u8 link_rate)
{
unsigned long flags;
struct _sas_node *sas_node;
struct _sas_phy *mpt3sas_phy;
if (ioc->shost_recovery || ioc->pci_error_recovery)
return;
spin_lock_irqsave(&ioc->sas_node_lock, flags);
sas_node = _transport_sas_node_find_by_sas_address(ioc, sas_address);
if (!sas_node) {
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
return;
}
mpt3sas_phy = &sas_node->phy[phy_number];
mpt3sas_phy->attached_handle = handle;
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
if (handle && (link_rate >= MPI2_SAS_NEG_LINK_RATE_1_5)) {
_transport_set_identify(ioc, handle,
&mpt3sas_phy->remote_identify);
_transport_add_phy_to_an_existing_port(ioc, sas_node,
mpt3sas_phy, mpt3sas_phy->remote_identify.sas_address);
} else
memset(&mpt3sas_phy->remote_identify, 0 , sizeof(struct
sas_identify));
if (mpt3sas_phy->phy)
mpt3sas_phy->phy->negotiated_linkrate =
_transport_convert_phy_link_rate(link_rate);
if ((ioc->logging_level & MPT_DEBUG_TRANSPORT))
dev_printk(KERN_INFO, &mpt3sas_phy->phy->dev,
"refresh: parent sas_addr(0x%016llx),\n"
"\tlink_rate(0x%02x), phy(%d)\n"
"\tattached_handle(0x%04x), sas_addr(0x%016llx)\n",
(unsigned long long)sas_address,
link_rate, phy_number, handle, (unsigned long long)
mpt3sas_phy->remote_identify.sas_address);
}
static inline void *
phy_to_ioc(struct sas_phy *phy)
{
struct Scsi_Host *shost = dev_to_shost(phy->dev.parent);
return shost_priv(shost);
}
static inline void *
rphy_to_ioc(struct sas_rphy *rphy)
{
struct Scsi_Host *shost = dev_to_shost(rphy->dev.parent->parent);
return shost_priv(shost);
}
/* report phy error log structure */
struct phy_error_log_request {
u8 smp_frame_type; /* 0x40 */
u8 function; /* 0x11 */
u8 allocated_response_length;
u8 request_length; /* 02 */
u8 reserved_1[5];
u8 phy_identifier;
u8 reserved_2[2];
};
/* report phy error log reply structure */
struct phy_error_log_reply {
u8 smp_frame_type; /* 0x41 */
u8 function; /* 0x11 */
u8 function_result;
u8 response_length;
__be16 expander_change_count;
u8 reserved_1[3];
u8 phy_identifier;
u8 reserved_2[2];
__be32 invalid_dword;
__be32 running_disparity_error;
__be32 loss_of_dword_sync;
__be32 phy_reset_problem;
};
/**
* _transport_get_expander_phy_error_log - return expander counters
* @ioc: per adapter object
* @phy: The sas phy object
*
* Return: 0 for success, non-zero for failure.
*
*/
static int
_transport_get_expander_phy_error_log(struct MPT3SAS_ADAPTER *ioc,
struct sas_phy *phy)
{
Mpi2SmpPassthroughRequest_t *mpi_request;
Mpi2SmpPassthroughReply_t *mpi_reply;
struct phy_error_log_request *phy_error_log_request;
struct phy_error_log_reply *phy_error_log_reply;
int rc;
u16 smid;
void *psge;
u8 issue_reset = 0;
void *data_out = NULL;
dma_addr_t data_out_dma;
u32 sz;
if (ioc->shost_recovery || ioc->pci_error_recovery) {
ioc_info(ioc, "%s: host reset in progress!\n", __func__);
return -EFAULT;
}
mutex_lock(&ioc->transport_cmds.mutex);
if (ioc->transport_cmds.status != MPT3_CMD_NOT_USED) {
ioc_err(ioc, "%s: transport_cmds in use\n", __func__);
rc = -EAGAIN;
goto out;
}
ioc->transport_cmds.status = MPT3_CMD_PENDING;
rc = mpt3sas_wait_for_ioc(ioc, IOC_OPERATIONAL_WAIT_COUNT);
if (rc)
goto out;
smid = mpt3sas_base_get_smid(ioc, ioc->transport_cb_idx);
if (!smid) {
ioc_err(ioc, "%s: failed obtaining a smid\n", __func__);
rc = -EAGAIN;
goto out;
}
mpi_request = mpt3sas_base_get_msg_frame(ioc, smid);
ioc->transport_cmds.smid = smid;
sz = sizeof(struct phy_error_log_request) +
sizeof(struct phy_error_log_reply);
data_out = dma_alloc_coherent(&ioc->pdev->dev, sz, &data_out_dma,
GFP_KERNEL);
if (!data_out) {
pr_err("failure at %s:%d/%s()!\n", __FILE__,
__LINE__, __func__);
rc = -ENOMEM;
mpt3sas_base_free_smid(ioc, smid);
goto out;
}
rc = -EINVAL;
memset(data_out, 0, sz);
phy_error_log_request = data_out;
phy_error_log_request->smp_frame_type = 0x40;
phy_error_log_request->function = 0x11;
phy_error_log_request->request_length = 2;
phy_error_log_request->allocated_response_length = 0;
phy_error_log_request->phy_identifier = phy->number;
memset(mpi_request, 0, sizeof(Mpi2SmpPassthroughRequest_t));
mpi_request->Function = MPI2_FUNCTION_SMP_PASSTHROUGH;
mpi_request->PhysicalPort = 0xFF;
mpi_request->VF_ID = 0; /* TODO */
mpi_request->VP_ID = 0;
mpi_request->SASAddress = cpu_to_le64(phy->identify.sas_address);
mpi_request->RequestDataLength =
cpu_to_le16(sizeof(struct phy_error_log_request));
psge = &mpi_request->SGL;
ioc->build_sg(ioc, psge, data_out_dma,
sizeof(struct phy_error_log_request),
data_out_dma + sizeof(struct phy_error_log_request),
sizeof(struct phy_error_log_reply));
dtransportprintk(ioc,
ioc_info(ioc, "phy_error_log - send to sas_addr(0x%016llx), phy(%d)\n",
(u64)phy->identify.sas_address,
phy->number));
init_completion(&ioc->transport_cmds.done);
ioc->put_smid_default(ioc, smid);
wait_for_completion_timeout(&ioc->transport_cmds.done, 10*HZ);
if (!(ioc->transport_cmds.status & MPT3_CMD_COMPLETE)) {
ioc_err(ioc, "%s: timeout\n", __func__);
_debug_dump_mf(mpi_request,
sizeof(Mpi2SmpPassthroughRequest_t)/4);
if (!(ioc->transport_cmds.status & MPT3_CMD_RESET))
issue_reset = 1;
goto issue_host_reset;
}
dtransportprintk(ioc, ioc_info(ioc, "phy_error_log - complete\n"));
if (ioc->transport_cmds.status & MPT3_CMD_REPLY_VALID) {
mpi_reply = ioc->transport_cmds.reply;
dtransportprintk(ioc,
ioc_info(ioc, "phy_error_log - reply data transfer size(%d)\n",
le16_to_cpu(mpi_reply->ResponseDataLength)));
if (le16_to_cpu(mpi_reply->ResponseDataLength) !=
sizeof(struct phy_error_log_reply))
goto out;
phy_error_log_reply = data_out +
sizeof(struct phy_error_log_request);
dtransportprintk(ioc,
ioc_info(ioc, "phy_error_log - function_result(%d)\n",
phy_error_log_reply->function_result));
phy->invalid_dword_count =
be32_to_cpu(phy_error_log_reply->invalid_dword);
phy->running_disparity_error_count =
be32_to_cpu(phy_error_log_reply->running_disparity_error);
phy->loss_of_dword_sync_count =
be32_to_cpu(phy_error_log_reply->loss_of_dword_sync);
phy->phy_reset_problem_count =
be32_to_cpu(phy_error_log_reply->phy_reset_problem);
rc = 0;
} else
dtransportprintk(ioc,
ioc_info(ioc, "phy_error_log - no reply\n"));
issue_host_reset:
if (issue_reset)
mpt3sas_base_hard_reset_handler(ioc, FORCE_BIG_HAMMER);
out:
ioc->transport_cmds.status = MPT3_CMD_NOT_USED;
if (data_out)
dma_free_coherent(&ioc->pdev->dev, sz, data_out, data_out_dma);
mutex_unlock(&ioc->transport_cmds.mutex);
return rc;
}
/**
* _transport_get_linkerrors - return phy counters for both hba and expanders
* @phy: The sas phy object
*
* Return: 0 for success, non-zero for failure.
*
*/
static int
_transport_get_linkerrors(struct sas_phy *phy)
{
struct MPT3SAS_ADAPTER *ioc = phy_to_ioc(phy);
unsigned long flags;
Mpi2ConfigReply_t mpi_reply;
Mpi2SasPhyPage1_t phy_pg1;
spin_lock_irqsave(&ioc->sas_node_lock, flags);
if (_transport_sas_node_find_by_sas_address(ioc,
phy->identify.sas_address) == NULL) {
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
return -EINVAL;
}
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
if (phy->identify.sas_address != ioc->sas_hba.sas_address)
return _transport_get_expander_phy_error_log(ioc, phy);
/* get hba phy error logs */
if ((mpt3sas_config_get_phy_pg1(ioc, &mpi_reply, &phy_pg1,
phy->number))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
return -ENXIO;
}
if (mpi_reply.IOCStatus || mpi_reply.IOCLogInfo)
ioc_info(ioc, "phy(%d), ioc_status (0x%04x), loginfo(0x%08x)\n",
phy->number,
le16_to_cpu(mpi_reply.IOCStatus),
le32_to_cpu(mpi_reply.IOCLogInfo));
phy->invalid_dword_count = le32_to_cpu(phy_pg1.InvalidDwordCount);
phy->running_disparity_error_count =
le32_to_cpu(phy_pg1.RunningDisparityErrorCount);
phy->loss_of_dword_sync_count =
le32_to_cpu(phy_pg1.LossDwordSynchCount);
phy->phy_reset_problem_count =
le32_to_cpu(phy_pg1.PhyResetProblemCount);
return 0;
}
/**
* _transport_get_enclosure_identifier -
* @rphy: The sas phy object
* @identifier: ?
*
* Obtain the enclosure logical id for an expander.
* Return: 0 for success, non-zero for failure.
*/
static int
_transport_get_enclosure_identifier(struct sas_rphy *rphy, u64 *identifier)
{
struct MPT3SAS_ADAPTER *ioc = rphy_to_ioc(rphy);
struct _sas_device *sas_device;
unsigned long flags;
int rc;
spin_lock_irqsave(&ioc->sas_device_lock, flags);
sas_device = __mpt3sas_get_sdev_by_addr(ioc,
rphy->identify.sas_address);
if (sas_device) {
*identifier = sas_device->enclosure_logical_id;
rc = 0;
sas_device_put(sas_device);
} else {
*identifier = 0;
rc = -ENXIO;
}
spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
return rc;
}
/**
* _transport_get_bay_identifier -
* @rphy: The sas phy object
*
* Return: the slot id for a device that resides inside an enclosure.
*/
static int
_transport_get_bay_identifier(struct sas_rphy *rphy)
{
struct MPT3SAS_ADAPTER *ioc = rphy_to_ioc(rphy);
struct _sas_device *sas_device;
unsigned long flags;
int rc;
spin_lock_irqsave(&ioc->sas_device_lock, flags);
sas_device = __mpt3sas_get_sdev_by_addr(ioc,
rphy->identify.sas_address);
if (sas_device) {
rc = sas_device->slot;
sas_device_put(sas_device);
} else {
rc = -ENXIO;
}
spin_unlock_irqrestore(&ioc->sas_device_lock, flags);
return rc;
}
/* phy control request structure */
struct phy_control_request {
u8 smp_frame_type; /* 0x40 */
u8 function; /* 0x91 */
u8 allocated_response_length;
u8 request_length; /* 0x09 */
u16 expander_change_count;
u8 reserved_1[3];
u8 phy_identifier;
u8 phy_operation;
u8 reserved_2[13];
u64 attached_device_name;
u8 programmed_min_physical_link_rate;
u8 programmed_max_physical_link_rate;
u8 reserved_3[6];
};
/* phy control reply structure */
struct phy_control_reply {
u8 smp_frame_type; /* 0x41 */
u8 function; /* 0x11 */
u8 function_result;
u8 response_length;
};
#define SMP_PHY_CONTROL_LINK_RESET (0x01)
#define SMP_PHY_CONTROL_HARD_RESET (0x02)
#define SMP_PHY_CONTROL_DISABLE (0x03)
/**
* _transport_expander_phy_control - expander phy control
* @ioc: per adapter object
* @phy: The sas phy object
* @phy_operation: ?
*
* Return: 0 for success, non-zero for failure.
*
*/
static int
_transport_expander_phy_control(struct MPT3SAS_ADAPTER *ioc,
struct sas_phy *phy, u8 phy_operation)
{
Mpi2SmpPassthroughRequest_t *mpi_request;
Mpi2SmpPassthroughReply_t *mpi_reply;
struct phy_control_request *phy_control_request;
struct phy_control_reply *phy_control_reply;
int rc;
u16 smid;
void *psge;
u8 issue_reset = 0;
void *data_out = NULL;
dma_addr_t data_out_dma;
u32 sz;
if (ioc->shost_recovery || ioc->pci_error_recovery) {
ioc_info(ioc, "%s: host reset in progress!\n", __func__);
return -EFAULT;
}
mutex_lock(&ioc->transport_cmds.mutex);
if (ioc->transport_cmds.status != MPT3_CMD_NOT_USED) {
ioc_err(ioc, "%s: transport_cmds in use\n", __func__);
rc = -EAGAIN;
goto out;
}
ioc->transport_cmds.status = MPT3_CMD_PENDING;
rc = mpt3sas_wait_for_ioc(ioc, IOC_OPERATIONAL_WAIT_COUNT);
if (rc)
goto out;
smid = mpt3sas_base_get_smid(ioc, ioc->transport_cb_idx);
if (!smid) {
ioc_err(ioc, "%s: failed obtaining a smid\n", __func__);
rc = -EAGAIN;
goto out;
}
mpi_request = mpt3sas_base_get_msg_frame(ioc, smid);
ioc->transport_cmds.smid = smid;
sz = sizeof(struct phy_control_request) +
sizeof(struct phy_control_reply);
data_out = dma_alloc_coherent(&ioc->pdev->dev, sz, &data_out_dma,
GFP_KERNEL);
if (!data_out) {
pr_err("failure at %s:%d/%s()!\n", __FILE__,
__LINE__, __func__);
rc = -ENOMEM;
mpt3sas_base_free_smid(ioc, smid);
goto out;
}
rc = -EINVAL;
memset(data_out, 0, sz);
phy_control_request = data_out;
phy_control_request->smp_frame_type = 0x40;
phy_control_request->function = 0x91;
phy_control_request->request_length = 9;
phy_control_request->allocated_response_length = 0;
phy_control_request->phy_identifier = phy->number;
phy_control_request->phy_operation = phy_operation;
phy_control_request->programmed_min_physical_link_rate =
phy->minimum_linkrate << 4;
phy_control_request->programmed_max_physical_link_rate =
phy->maximum_linkrate << 4;
memset(mpi_request, 0, sizeof(Mpi2SmpPassthroughRequest_t));
mpi_request->Function = MPI2_FUNCTION_SMP_PASSTHROUGH;
mpi_request->PhysicalPort = 0xFF;
mpi_request->VF_ID = 0; /* TODO */
mpi_request->VP_ID = 0;
mpi_request->SASAddress = cpu_to_le64(phy->identify.sas_address);
mpi_request->RequestDataLength =
cpu_to_le16(sizeof(struct phy_error_log_request));
psge = &mpi_request->SGL;
ioc->build_sg(ioc, psge, data_out_dma,
sizeof(struct phy_control_request),
data_out_dma + sizeof(struct phy_control_request),
sizeof(struct phy_control_reply));
dtransportprintk(ioc,
ioc_info(ioc, "phy_control - send to sas_addr(0x%016llx), phy(%d), opcode(%d)\n",
(u64)phy->identify.sas_address,
phy->number, phy_operation));
init_completion(&ioc->transport_cmds.done);
ioc->put_smid_default(ioc, smid);
wait_for_completion_timeout(&ioc->transport_cmds.done, 10*HZ);
if (!(ioc->transport_cmds.status & MPT3_CMD_COMPLETE)) {
ioc_err(ioc, "%s: timeout\n", __func__);
_debug_dump_mf(mpi_request,
sizeof(Mpi2SmpPassthroughRequest_t)/4);
if (!(ioc->transport_cmds.status & MPT3_CMD_RESET))
issue_reset = 1;
goto issue_host_reset;
}
dtransportprintk(ioc, ioc_info(ioc, "phy_control - complete\n"));
if (ioc->transport_cmds.status & MPT3_CMD_REPLY_VALID) {
mpi_reply = ioc->transport_cmds.reply;
dtransportprintk(ioc,
ioc_info(ioc, "phy_control - reply data transfer size(%d)\n",
le16_to_cpu(mpi_reply->ResponseDataLength)));
if (le16_to_cpu(mpi_reply->ResponseDataLength) !=
sizeof(struct phy_control_reply))
goto out;
phy_control_reply = data_out +
sizeof(struct phy_control_request);
dtransportprintk(ioc,
ioc_info(ioc, "phy_control - function_result(%d)\n",
phy_control_reply->function_result));
rc = 0;
} else
dtransportprintk(ioc,
ioc_info(ioc, "phy_control - no reply\n"));
issue_host_reset:
if (issue_reset)
mpt3sas_base_hard_reset_handler(ioc, FORCE_BIG_HAMMER);
out:
ioc->transport_cmds.status = MPT3_CMD_NOT_USED;
if (data_out)
dma_free_coherent(&ioc->pdev->dev, sz, data_out,
data_out_dma);
mutex_unlock(&ioc->transport_cmds.mutex);
return rc;
}
/**
* _transport_phy_reset -
* @phy: The sas phy object
* @hard_reset:
*
* Return: 0 for success, non-zero for failure.
*/
static int
_transport_phy_reset(struct sas_phy *phy, int hard_reset)
{
struct MPT3SAS_ADAPTER *ioc = phy_to_ioc(phy);
Mpi2SasIoUnitControlReply_t mpi_reply;
Mpi2SasIoUnitControlRequest_t mpi_request;
unsigned long flags;
spin_lock_irqsave(&ioc->sas_node_lock, flags);
if (_transport_sas_node_find_by_sas_address(ioc,
phy->identify.sas_address) == NULL) {
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
return -EINVAL;
}
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
/* handle expander phys */
if (phy->identify.sas_address != ioc->sas_hba.sas_address)
return _transport_expander_phy_control(ioc, phy,
(hard_reset == 1) ? SMP_PHY_CONTROL_HARD_RESET :
SMP_PHY_CONTROL_LINK_RESET);
/* handle hba phys */
memset(&mpi_request, 0, sizeof(Mpi2SasIoUnitControlRequest_t));
mpi_request.Function = MPI2_FUNCTION_SAS_IO_UNIT_CONTROL;
mpi_request.Operation = hard_reset ?
MPI2_SAS_OP_PHY_HARD_RESET : MPI2_SAS_OP_PHY_LINK_RESET;
mpi_request.PhyNum = phy->number;
if ((mpt3sas_base_sas_iounit_control(ioc, &mpi_reply, &mpi_request))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
return -ENXIO;
}
if (mpi_reply.IOCStatus || mpi_reply.IOCLogInfo)
ioc_info(ioc, "phy(%d), ioc_status(0x%04x), loginfo(0x%08x)\n",
phy->number, le16_to_cpu(mpi_reply.IOCStatus),
le32_to_cpu(mpi_reply.IOCLogInfo));
return 0;
}
/**
* _transport_phy_enable - enable/disable phys
* @phy: The sas phy object
* @enable: enable phy when true
*
* Only support sas_host direct attached phys.
* Return: 0 for success, non-zero for failure.
*/
static int
_transport_phy_enable(struct sas_phy *phy, int enable)
{
struct MPT3SAS_ADAPTER *ioc = phy_to_ioc(phy);
Mpi2SasIOUnitPage1_t *sas_iounit_pg1 = NULL;
Mpi2SasIOUnitPage0_t *sas_iounit_pg0 = NULL;
Mpi2ConfigReply_t mpi_reply;
u16 ioc_status;
u16 sz;
int rc = 0;
unsigned long flags;
int i, discovery_active;
spin_lock_irqsave(&ioc->sas_node_lock, flags);
if (_transport_sas_node_find_by_sas_address(ioc,
phy->identify.sas_address) == NULL) {
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
return -EINVAL;
}
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
/* handle expander phys */
if (phy->identify.sas_address != ioc->sas_hba.sas_address)
return _transport_expander_phy_control(ioc, phy,
(enable == 1) ? SMP_PHY_CONTROL_LINK_RESET :
SMP_PHY_CONTROL_DISABLE);
/* handle hba phys */
/* read sas_iounit page 0 */
sz = offsetof(Mpi2SasIOUnitPage0_t, PhyData) + (ioc->sas_hba.num_phys *
sizeof(Mpi2SasIOUnit0PhyData_t));
sas_iounit_pg0 = kzalloc(sz, GFP_KERNEL);
if (!sas_iounit_pg0) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
rc = -ENOMEM;
goto out;
}
if ((mpt3sas_config_get_sas_iounit_pg0(ioc, &mpi_reply,
sas_iounit_pg0, sz))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
rc = -ENXIO;
goto out;
}
ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
MPI2_IOCSTATUS_MASK;
if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
rc = -EIO;
goto out;
}
/* unable to enable/disable phys when when discovery is active */
for (i = 0, discovery_active = 0; i < ioc->sas_hba.num_phys ; i++) {
if (sas_iounit_pg0->PhyData[i].PortFlags &
MPI2_SASIOUNIT0_PORTFLAGS_DISCOVERY_IN_PROGRESS) {
ioc_err(ioc, "discovery is active on port = %d, phy = %d: unable to enable/disable phys, try again later!\n",
sas_iounit_pg0->PhyData[i].Port, i);
discovery_active = 1;
}
}
if (discovery_active) {
rc = -EAGAIN;
goto out;
}
/* read sas_iounit page 1 */
sz = offsetof(Mpi2SasIOUnitPage1_t, PhyData) + (ioc->sas_hba.num_phys *
sizeof(Mpi2SasIOUnit1PhyData_t));
sas_iounit_pg1 = kzalloc(sz, GFP_KERNEL);
if (!sas_iounit_pg1) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
rc = -ENOMEM;
goto out;
}
if ((mpt3sas_config_get_sas_iounit_pg1(ioc, &mpi_reply,
sas_iounit_pg1, sz))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
rc = -ENXIO;
goto out;
}
ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
MPI2_IOCSTATUS_MASK;
if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
rc = -EIO;
goto out;
}
/* copy Port/PortFlags/PhyFlags from page 0 */
for (i = 0; i < ioc->sas_hba.num_phys ; i++) {
sas_iounit_pg1->PhyData[i].Port =
sas_iounit_pg0->PhyData[i].Port;
sas_iounit_pg1->PhyData[i].PortFlags =
(sas_iounit_pg0->PhyData[i].PortFlags &
MPI2_SASIOUNIT0_PORTFLAGS_AUTO_PORT_CONFIG);
sas_iounit_pg1->PhyData[i].PhyFlags =
(sas_iounit_pg0->PhyData[i].PhyFlags &
(MPI2_SASIOUNIT0_PHYFLAGS_ZONING_ENABLED +
MPI2_SASIOUNIT0_PHYFLAGS_PHY_DISABLED));
}
if (enable)
sas_iounit_pg1->PhyData[phy->number].PhyFlags
&= ~MPI2_SASIOUNIT1_PHYFLAGS_PHY_DISABLE;
else
sas_iounit_pg1->PhyData[phy->number].PhyFlags
|= MPI2_SASIOUNIT1_PHYFLAGS_PHY_DISABLE;
mpt3sas_config_set_sas_iounit_pg1(ioc, &mpi_reply, sas_iounit_pg1, sz);
/* link reset */
if (enable)
_transport_phy_reset(phy, 0);
out:
kfree(sas_iounit_pg1);
kfree(sas_iounit_pg0);
return rc;
}
/**
* _transport_phy_speed - set phy min/max link rates
* @phy: The sas phy object
* @rates: rates defined in sas_phy_linkrates
*
* Only support sas_host direct attached phys.
*
* Return: 0 for success, non-zero for failure.
*/
static int
_transport_phy_speed(struct sas_phy *phy, struct sas_phy_linkrates *rates)
{
struct MPT3SAS_ADAPTER *ioc = phy_to_ioc(phy);
Mpi2SasIOUnitPage1_t *sas_iounit_pg1 = NULL;
Mpi2SasPhyPage0_t phy_pg0;
Mpi2ConfigReply_t mpi_reply;
u16 ioc_status;
u16 sz;
int i;
int rc = 0;
unsigned long flags;
spin_lock_irqsave(&ioc->sas_node_lock, flags);
if (_transport_sas_node_find_by_sas_address(ioc,
phy->identify.sas_address) == NULL) {
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
return -EINVAL;
}
spin_unlock_irqrestore(&ioc->sas_node_lock, flags);
if (!rates->minimum_linkrate)
rates->minimum_linkrate = phy->minimum_linkrate;
else if (rates->minimum_linkrate < phy->minimum_linkrate_hw)
rates->minimum_linkrate = phy->minimum_linkrate_hw;
if (!rates->maximum_linkrate)
rates->maximum_linkrate = phy->maximum_linkrate;
else if (rates->maximum_linkrate > phy->maximum_linkrate_hw)
rates->maximum_linkrate = phy->maximum_linkrate_hw;
/* handle expander phys */
if (phy->identify.sas_address != ioc->sas_hba.sas_address) {
phy->minimum_linkrate = rates->minimum_linkrate;
phy->maximum_linkrate = rates->maximum_linkrate;
return _transport_expander_phy_control(ioc, phy,
SMP_PHY_CONTROL_LINK_RESET);
}
/* handle hba phys */
/* sas_iounit page 1 */
sz = offsetof(Mpi2SasIOUnitPage1_t, PhyData) + (ioc->sas_hba.num_phys *
sizeof(Mpi2SasIOUnit1PhyData_t));
sas_iounit_pg1 = kzalloc(sz, GFP_KERNEL);
if (!sas_iounit_pg1) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
rc = -ENOMEM;
goto out;
}
if ((mpt3sas_config_get_sas_iounit_pg1(ioc, &mpi_reply,
sas_iounit_pg1, sz))) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
rc = -ENXIO;
goto out;
}
ioc_status = le16_to_cpu(mpi_reply.IOCStatus) &
MPI2_IOCSTATUS_MASK;
if (ioc_status != MPI2_IOCSTATUS_SUCCESS) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
rc = -EIO;
goto out;
}
for (i = 0; i < ioc->sas_hba.num_phys; i++) {
if (phy->number != i) {
sas_iounit_pg1->PhyData[i].MaxMinLinkRate =
(ioc->sas_hba.phy[i].phy->minimum_linkrate +
(ioc->sas_hba.phy[i].phy->maximum_linkrate << 4));
} else {
sas_iounit_pg1->PhyData[i].MaxMinLinkRate =
(rates->minimum_linkrate +
(rates->maximum_linkrate << 4));
}
}
if (mpt3sas_config_set_sas_iounit_pg1(ioc, &mpi_reply, sas_iounit_pg1,
sz)) {
ioc_err(ioc, "failure at %s:%d/%s()!\n",
__FILE__, __LINE__, __func__);
rc = -ENXIO;
goto out;
}
/* link reset */
_transport_phy_reset(phy, 0);
/* read phy page 0, then update the rates in the sas transport phy */
if (!mpt3sas_config_get_phy_pg0(ioc, &mpi_reply, &phy_pg0,
phy->number)) {
phy->minimum_linkrate = _transport_convert_phy_link_rate(
phy_pg0.ProgrammedLinkRate & MPI2_SAS_PRATE_MIN_RATE_MASK);
phy->maximum_linkrate = _transport_convert_phy_link_rate(
phy_pg0.ProgrammedLinkRate >> 4);
phy->negotiated_linkrate = _transport_convert_phy_link_rate(
phy_pg0.NegotiatedLinkRate &
MPI2_SAS_NEG_LINK_RATE_MASK_PHYSICAL);
}
out:
kfree(sas_iounit_pg1);
return rc;
}
static int
_transport_map_smp_buffer(struct device *dev, struct bsg_buffer *buf,
dma_addr_t *dma_addr, size_t *dma_len, void **p)
{
/* Check if the request is split across multiple segments */
if (buf->sg_cnt > 1) {
*p = dma_alloc_coherent(dev, buf->payload_len, dma_addr,
GFP_KERNEL);
if (!*p)
return -ENOMEM;
*dma_len = buf->payload_len;
} else {
if (!dma_map_sg(dev, buf->sg_list, 1, DMA_BIDIRECTIONAL))
return -ENOMEM;
*dma_addr = sg_dma_address(buf->sg_list);
*dma_len = sg_dma_len(buf->sg_list);
*p = NULL;
}
return 0;
}
static void
_transport_unmap_smp_buffer(struct device *dev, struct bsg_buffer *buf,
dma_addr_t dma_addr, void *p)
{
if (p)
dma_free_coherent(dev, buf->payload_len, p, dma_addr);
else
dma_unmap_sg(dev, buf->sg_list, 1, DMA_BIDIRECTIONAL);
}
/**
* _transport_smp_handler - transport portal for smp passthru
* @job: ?
* @shost: shost object
* @rphy: sas transport rphy object
*
* This used primarily for smp_utils.
* Example:
* smp_rep_general /sys/class/bsg/expander-5:0
*/
static void
_transport_smp_handler(struct bsg_job *job, struct Scsi_Host *shost,
struct sas_rphy *rphy)
{
struct MPT3SAS_ADAPTER *ioc = shost_priv(shost);
Mpi2SmpPassthroughRequest_t *mpi_request;
Mpi2SmpPassthroughReply_t *mpi_reply;
int rc;
u16 smid;
void *psge;
dma_addr_t dma_addr_in;
dma_addr_t dma_addr_out;
void *addr_in = NULL;
void *addr_out = NULL;
size_t dma_len_in;
size_t dma_len_out;
unsigned int reslen = 0;
if (ioc->shost_recovery || ioc->pci_error_recovery) {
ioc_info(ioc, "%s: host reset in progress!\n", __func__);
rc = -EFAULT;
goto job_done;
}
rc = mutex_lock_interruptible(&ioc->transport_cmds.mutex);
if (rc)
goto job_done;
if (ioc->transport_cmds.status != MPT3_CMD_NOT_USED) {
ioc_err(ioc, "%s: transport_cmds in use\n",
__func__);
rc = -EAGAIN;
goto out;
}
ioc->transport_cmds.status = MPT3_CMD_PENDING;
rc = _transport_map_smp_buffer(&ioc->pdev->dev, &job->request_payload,
&dma_addr_out, &dma_len_out, &addr_out);
if (rc)
goto out;
if (addr_out) {
sg_copy_to_buffer(job->request_payload.sg_list,
job->request_payload.sg_cnt, addr_out,
job->request_payload.payload_len);
}
rc = _transport_map_smp_buffer(&ioc->pdev->dev, &job->reply_payload,
&dma_addr_in, &dma_len_in, &addr_in);
if (rc)
goto unmap_out;
rc = mpt3sas_wait_for_ioc(ioc, IOC_OPERATIONAL_WAIT_COUNT);
if (rc)
goto unmap_in;
smid = mpt3sas_base_get_smid(ioc, ioc->transport_cb_idx);
if (!smid) {
ioc_err(ioc, "%s: failed obtaining a smid\n", __func__);
rc = -EAGAIN;
goto unmap_in;
}
rc = 0;
mpi_request = mpt3sas_base_get_msg_frame(ioc, smid);
ioc->transport_cmds.smid = smid;
memset(mpi_request, 0, sizeof(Mpi2SmpPassthroughRequest_t));
mpi_request->Function = MPI2_FUNCTION_SMP_PASSTHROUGH;
mpi_request->PhysicalPort = 0xFF;
mpi_request->SASAddress = (rphy) ?
cpu_to_le64(rphy->identify.sas_address) :
cpu_to_le64(ioc->sas_hba.sas_address);
mpi_request->RequestDataLength = cpu_to_le16(dma_len_out - 4);
psge = &mpi_request->SGL;
ioc->build_sg(ioc, psge, dma_addr_out, dma_len_out - 4, dma_addr_in,
dma_len_in - 4);
dtransportprintk(ioc,
ioc_info(ioc, "%s: sending smp request\n", __func__));
init_completion(&ioc->transport_cmds.done);
ioc->put_smid_default(ioc, smid);
wait_for_completion_timeout(&ioc->transport_cmds.done, 10*HZ);
if (!(ioc->transport_cmds.status & MPT3_CMD_COMPLETE)) {
ioc_err(ioc, "%s: timeout\n", __func__);
_debug_dump_mf(mpi_request,
sizeof(Mpi2SmpPassthroughRequest_t)/4);
if (!(ioc->transport_cmds.status & MPT3_CMD_RESET)) {
mpt3sas_base_hard_reset_handler(ioc, FORCE_BIG_HAMMER);
rc = -ETIMEDOUT;
goto unmap_in;
}
}
dtransportprintk(ioc, ioc_info(ioc, "%s - complete\n", __func__));
if (!(ioc->transport_cmds.status & MPT3_CMD_REPLY_VALID)) {
dtransportprintk(ioc,
ioc_info(ioc, "%s: no reply\n", __func__));
rc = -ENXIO;
goto unmap_in;
}
mpi_reply = ioc->transport_cmds.reply;
dtransportprintk(ioc,
ioc_info(ioc, "%s: reply data transfer size(%d)\n",
__func__,
le16_to_cpu(mpi_reply->ResponseDataLength)));
memcpy(job->reply, mpi_reply, sizeof(*mpi_reply));
job->reply_len = sizeof(*mpi_reply);
reslen = le16_to_cpu(mpi_reply->ResponseDataLength);
if (addr_in) {
sg_copy_to_buffer(job->reply_payload.sg_list,
job->reply_payload.sg_cnt, addr_in,
job->reply_payload.payload_len);
}
rc = 0;
unmap_in:
_transport_unmap_smp_buffer(&ioc->pdev->dev, &job->reply_payload,
dma_addr_in, addr_in);
unmap_out:
_transport_unmap_smp_buffer(&ioc->pdev->dev, &job->request_payload,
dma_addr_out, addr_out);
out:
ioc->transport_cmds.status = MPT3_CMD_NOT_USED;
mutex_unlock(&ioc->transport_cmds.mutex);
job_done:
bsg_job_done(job, rc, reslen);
}
struct sas_function_template mpt3sas_transport_functions = {
.get_linkerrors = _transport_get_linkerrors,
.get_enclosure_identifier = _transport_get_enclosure_identifier,
.get_bay_identifier = _transport_get_bay_identifier,
.phy_reset = _transport_phy_reset,
.phy_enable = _transport_phy_enable,
.set_phy_speed = _transport_phy_speed,
.smp_handler = _transport_smp_handler,
};
struct scsi_transport_template *mpt3sas_transport_template;