linux/drivers/spi/spi-falcon.c
Hauke Mehrtens 1a41aa1376 spi: spi-falcon: drop check of boot select
Do not check which flash type the SoC was booted from before
using this driver. Assume that the device tree is correct and use this
driver when it was added to device tree. This also removes a build
dependency to the SoC code.

All device trees I am aware of only have one correct flash device entry
in it. The device tree is anyway bundled with the kernel in all systems
using device tree I know of.

The boot mode can be specified with some pin straps and will select the
flash type the rom code will boot from. One SPI, NOR or NAND flash chip
can be connect to the EBU and used to load the first stage boot loader
from.

Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Mark Brown <broonie@kernel.org>
Cc: linux-spi@vger.kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
2017-09-01 11:33:22 +01:00

435 lines
10 KiB
C

/*
* This program is free software; you can redistribute it and/or modify it
* under the terms of the GNU General Public License version 2 as published
* by the Free Software Foundation.
*
* Copyright (C) 2012 Thomas Langer <thomas.langer@lantiq.com>
*/
#include <linux/module.h>
#include <linux/device.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/delay.h>
#include <linux/of.h>
#include <linux/of_platform.h>
#include <lantiq_soc.h>
#define DRV_NAME "sflash-falcon"
#define FALCON_SPI_XFER_BEGIN (1 << 0)
#define FALCON_SPI_XFER_END (1 << 1)
/* Bus Read Configuration Register0 */
#define BUSRCON0 0x00000010
/* Bus Write Configuration Register0 */
#define BUSWCON0 0x00000018
/* Serial Flash Configuration Register */
#define SFCON 0x00000080
/* Serial Flash Time Register */
#define SFTIME 0x00000084
/* Serial Flash Status Register */
#define SFSTAT 0x00000088
/* Serial Flash Command Register */
#define SFCMD 0x0000008C
/* Serial Flash Address Register */
#define SFADDR 0x00000090
/* Serial Flash Data Register */
#define SFDATA 0x00000094
/* Serial Flash I/O Control Register */
#define SFIO 0x00000098
/* EBU Clock Control Register */
#define EBUCC 0x000000C4
/* Dummy Phase Length */
#define SFCMD_DUMLEN_OFFSET 16
#define SFCMD_DUMLEN_MASK 0x000F0000
/* Chip Select */
#define SFCMD_CS_OFFSET 24
#define SFCMD_CS_MASK 0x07000000
/* field offset */
#define SFCMD_ALEN_OFFSET 20
#define SFCMD_ALEN_MASK 0x00700000
/* SCK Rise-edge Position */
#define SFTIME_SCKR_POS_OFFSET 8
#define SFTIME_SCKR_POS_MASK 0x00000F00
/* SCK Period */
#define SFTIME_SCK_PER_OFFSET 0
#define SFTIME_SCK_PER_MASK 0x0000000F
/* SCK Fall-edge Position */
#define SFTIME_SCKF_POS_OFFSET 12
#define SFTIME_SCKF_POS_MASK 0x0000F000
/* Device Size */
#define SFCON_DEV_SIZE_A23_0 0x03000000
#define SFCON_DEV_SIZE_MASK 0x0F000000
/* Read Data Position */
#define SFTIME_RD_POS_MASK 0x000F0000
/* Data Output */
#define SFIO_UNUSED_WD_MASK 0x0000000F
/* Command Opcode mask */
#define SFCMD_OPC_MASK 0x000000FF
/* dlen bytes of data to write */
#define SFCMD_DIR_WRITE 0x00000100
/* Data Length offset */
#define SFCMD_DLEN_OFFSET 9
/* Command Error */
#define SFSTAT_CMD_ERR 0x20000000
/* Access Command Pending */
#define SFSTAT_CMD_PEND 0x00400000
/* Frequency set to 100MHz. */
#define EBUCC_EBUDIV_SELF100 0x00000001
/* Serial Flash */
#define BUSRCON0_AGEN_SERIAL_FLASH 0xF0000000
/* 8-bit multiplexed */
#define BUSRCON0_PORTW_8_BIT_MUX 0x00000000
/* Serial Flash */
#define BUSWCON0_AGEN_SERIAL_FLASH 0xF0000000
/* Chip Select after opcode */
#define SFCMD_KEEP_CS_KEEP_SELECTED 0x00008000
#define CLOCK_100M 100000000
#define CLOCK_50M 50000000
struct falcon_sflash {
u32 sfcmd; /* for caching of opcode, direction, ... */
struct spi_master *master;
};
int falcon_sflash_xfer(struct spi_device *spi, struct spi_transfer *t,
unsigned long flags)
{
struct device *dev = &spi->dev;
struct falcon_sflash *priv = spi_master_get_devdata(spi->master);
const u8 *txp = t->tx_buf;
u8 *rxp = t->rx_buf;
unsigned int bytelen = ((8 * t->len + 7) / 8);
unsigned int len, alen, dumlen;
u32 val;
enum {
state_init,
state_command_prepare,
state_write,
state_read,
state_disable_cs,
state_end
} state = state_init;
do {
switch (state) {
case state_init: /* detect phase of upper layer sequence */
{
/* initial write ? */
if (flags & FALCON_SPI_XFER_BEGIN) {
if (!txp) {
dev_err(dev,
"BEGIN without tx data!\n");
return -ENODATA;
}
/*
* Prepare the parts of the sfcmd register,
* which should not change during a sequence!
* Only exception are the length fields,
* especially alen and dumlen.
*/
priv->sfcmd = ((spi->chip_select
<< SFCMD_CS_OFFSET)
& SFCMD_CS_MASK);
priv->sfcmd |= SFCMD_KEEP_CS_KEEP_SELECTED;
priv->sfcmd |= *txp;
txp++;
bytelen--;
if (bytelen) {
/*
* more data:
* maybe address and/or dummy
*/
state = state_command_prepare;
break;
} else {
dev_dbg(dev, "write cmd %02X\n",
priv->sfcmd & SFCMD_OPC_MASK);
}
}
/* continued write ? */
if (txp && bytelen) {
state = state_write;
break;
}
/* read data? */
if (rxp && bytelen) {
state = state_read;
break;
}
/* end of sequence? */
if (flags & FALCON_SPI_XFER_END)
state = state_disable_cs;
else
state = state_end;
break;
}
/* collect tx data for address and dummy phase */
case state_command_prepare:
{
/* txp is valid, already checked */
val = 0;
alen = 0;
dumlen = 0;
while (bytelen > 0) {
if (alen < 3) {
val = (val << 8) | (*txp++);
alen++;
} else if ((dumlen < 15) && (*txp == 0)) {
/*
* assume dummy bytes are set to 0
* from upper layer
*/
dumlen++;
txp++;
} else {
break;
}
bytelen--;
}
priv->sfcmd &= ~(SFCMD_ALEN_MASK | SFCMD_DUMLEN_MASK);
priv->sfcmd |= (alen << SFCMD_ALEN_OFFSET) |
(dumlen << SFCMD_DUMLEN_OFFSET);
if (alen > 0)
ltq_ebu_w32(val, SFADDR);
dev_dbg(dev, "wr %02X, alen=%d (addr=%06X) dlen=%d\n",
priv->sfcmd & SFCMD_OPC_MASK,
alen, val, dumlen);
if (bytelen > 0) {
/* continue with write */
state = state_write;
} else if (flags & FALCON_SPI_XFER_END) {
/* end of sequence? */
state = state_disable_cs;
} else {
/*
* go to end and expect another
* call (read or write)
*/
state = state_end;
}
break;
}
case state_write:
{
/* txp still valid */
priv->sfcmd |= SFCMD_DIR_WRITE;
len = 0;
val = 0;
do {
if (bytelen--)
val |= (*txp++) << (8 * len++);
if ((flags & FALCON_SPI_XFER_END)
&& (bytelen == 0)) {
priv->sfcmd &=
~SFCMD_KEEP_CS_KEEP_SELECTED;
}
if ((len == 4) || (bytelen == 0)) {
ltq_ebu_w32(val, SFDATA);
ltq_ebu_w32(priv->sfcmd
| (len<<SFCMD_DLEN_OFFSET),
SFCMD);
len = 0;
val = 0;
priv->sfcmd &= ~(SFCMD_ALEN_MASK
| SFCMD_DUMLEN_MASK);
}
} while (bytelen);
state = state_end;
break;
}
case state_read:
{
/* read data */
priv->sfcmd &= ~SFCMD_DIR_WRITE;
do {
if ((flags & FALCON_SPI_XFER_END)
&& (bytelen <= 4)) {
priv->sfcmd &=
~SFCMD_KEEP_CS_KEEP_SELECTED;
}
len = (bytelen > 4) ? 4 : bytelen;
bytelen -= len;
ltq_ebu_w32(priv->sfcmd
| (len << SFCMD_DLEN_OFFSET), SFCMD);
priv->sfcmd &= ~(SFCMD_ALEN_MASK
| SFCMD_DUMLEN_MASK);
do {
val = ltq_ebu_r32(SFSTAT);
if (val & SFSTAT_CMD_ERR) {
/* reset error status */
dev_err(dev, "SFSTAT: CMD_ERR");
dev_err(dev, " (%x)\n", val);
ltq_ebu_w32(SFSTAT_CMD_ERR,
SFSTAT);
return -EBADE;
}
} while (val & SFSTAT_CMD_PEND);
val = ltq_ebu_r32(SFDATA);
do {
*rxp = (val & 0xFF);
rxp++;
val >>= 8;
len--;
} while (len);
} while (bytelen);
state = state_end;
break;
}
case state_disable_cs:
{
priv->sfcmd &= ~SFCMD_KEEP_CS_KEEP_SELECTED;
ltq_ebu_w32(priv->sfcmd | (0 << SFCMD_DLEN_OFFSET),
SFCMD);
val = ltq_ebu_r32(SFSTAT);
if (val & SFSTAT_CMD_ERR) {
/* reset error status */
dev_err(dev, "SFSTAT: CMD_ERR (%x)\n", val);
ltq_ebu_w32(SFSTAT_CMD_ERR, SFSTAT);
return -EBADE;
}
state = state_end;
break;
}
case state_end:
break;
}
} while (state != state_end);
return 0;
}
static int falcon_sflash_setup(struct spi_device *spi)
{
unsigned int i;
unsigned long flags;
spin_lock_irqsave(&ebu_lock, flags);
if (spi->max_speed_hz >= CLOCK_100M) {
/* set EBU clock to 100 MHz */
ltq_sys1_w32_mask(0, EBUCC_EBUDIV_SELF100, EBUCC);
i = 1; /* divider */
} else {
/* set EBU clock to 50 MHz */
ltq_sys1_w32_mask(EBUCC_EBUDIV_SELF100, 0, EBUCC);
/* search for suitable divider */
for (i = 1; i < 7; i++) {
if (CLOCK_50M / i <= spi->max_speed_hz)
break;
}
}
/* setup period of serial clock */
ltq_ebu_w32_mask(SFTIME_SCKF_POS_MASK
| SFTIME_SCKR_POS_MASK
| SFTIME_SCK_PER_MASK,
(i << SFTIME_SCKR_POS_OFFSET)
| (i << (SFTIME_SCK_PER_OFFSET + 1)),
SFTIME);
/*
* set some bits of unused_wd, to not trigger HOLD/WP
* signals on non QUAD flashes
*/
ltq_ebu_w32((SFIO_UNUSED_WD_MASK & (0x8 | 0x4)), SFIO);
ltq_ebu_w32(BUSRCON0_AGEN_SERIAL_FLASH | BUSRCON0_PORTW_8_BIT_MUX,
BUSRCON0);
ltq_ebu_w32(BUSWCON0_AGEN_SERIAL_FLASH, BUSWCON0);
/* set address wrap around to maximum for 24-bit addresses */
ltq_ebu_w32_mask(SFCON_DEV_SIZE_MASK, SFCON_DEV_SIZE_A23_0, SFCON);
spin_unlock_irqrestore(&ebu_lock, flags);
return 0;
}
static int falcon_sflash_xfer_one(struct spi_master *master,
struct spi_message *m)
{
struct falcon_sflash *priv = spi_master_get_devdata(master);
struct spi_transfer *t;
unsigned long spi_flags;
unsigned long flags;
int ret = 0;
priv->sfcmd = 0;
m->actual_length = 0;
spi_flags = FALCON_SPI_XFER_BEGIN;
list_for_each_entry(t, &m->transfers, transfer_list) {
if (list_is_last(&t->transfer_list, &m->transfers))
spi_flags |= FALCON_SPI_XFER_END;
spin_lock_irqsave(&ebu_lock, flags);
ret = falcon_sflash_xfer(m->spi, t, spi_flags);
spin_unlock_irqrestore(&ebu_lock, flags);
if (ret)
break;
m->actual_length += t->len;
WARN_ON(t->delay_usecs || t->cs_change);
spi_flags = 0;
}
m->status = ret;
spi_finalize_current_message(master);
return 0;
}
static int falcon_sflash_probe(struct platform_device *pdev)
{
struct falcon_sflash *priv;
struct spi_master *master;
int ret;
master = spi_alloc_master(&pdev->dev, sizeof(*priv));
if (!master)
return -ENOMEM;
priv = spi_master_get_devdata(master);
priv->master = master;
master->mode_bits = SPI_MODE_3;
master->flags = SPI_MASTER_HALF_DUPLEX;
master->setup = falcon_sflash_setup;
master->transfer_one_message = falcon_sflash_xfer_one;
master->dev.of_node = pdev->dev.of_node;
ret = devm_spi_register_master(&pdev->dev, master);
if (ret)
spi_master_put(master);
return ret;
}
static const struct of_device_id falcon_sflash_match[] = {
{ .compatible = "lantiq,sflash-falcon" },
{},
};
MODULE_DEVICE_TABLE(of, falcon_sflash_match);
static struct platform_driver falcon_sflash_driver = {
.probe = falcon_sflash_probe,
.driver = {
.name = DRV_NAME,
.of_match_table = falcon_sflash_match,
}
};
module_platform_driver(falcon_sflash_driver);
MODULE_LICENSE("GPL");
MODULE_DESCRIPTION("Lantiq Falcon SPI/SFLASH controller driver");