linux/Documentation/hwmon/ltc2947.rst
Nuno Sá 9f90fd652b hwmon: Add support for ltc2947
The ltc2947 is a high precision power and energy monitor with an
internal sense resistor supporting up to +/- 30A. Three internal no
Latency ADCs ensure accurate measurement of voltage and current, while
high-bandwidth analog multiplication of voltage and current provides
accurate power measurement in a wide range of applications. Internal or
external clocking options enable precise charge and energy measurements.

Signed-off-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20191021154115.319073-1-nuno.sa@analog.com
[groeck: Removed unnecessary checks when reading temperature and energy;
	 PAGE{0,1} -> LTC2947_PAGE_{0,1}]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
2019-11-06 14:37:19 -08:00

101 lines
3.5 KiB
ReStructuredText

Kernel drivers ltc2947-i2c and ltc2947-spi
==========================================
Supported chips:
* Analog Devices LTC2947
Prefix: 'ltc2947'
Addresses scanned: -
Datasheet:
https://www.analog.com/media/en/technical-documentation/data-sheets/LTC2947.pdf
Author: Nuno Sá <nuno.sa@analog.com>
Description
___________
The LTC2947 is a high precision power and energy monitor that measures current,
voltage, power, temperature, charge and energy. The device supports both SPI
and I2C depending on the chip configuration.
The device also measures accumulated quantities as energy. It has two banks of
register's to read/set energy related values. These banks can be configured
independently to have setups like: energy1 accumulates always and enrgy2 only
accumulates if current is positive (to check battery charging efficiency for
example). The device also supports a GPIO pin that can be configured as output
to control a fan as a function of measured temperature. Then, the GPIO becomes
active as soon as a temperature reading is higher than a defined threshold. The
temp2 channel is used to control this thresholds and to read the respective
alarms.
Sysfs entries
_____________
The following attributes are supported. Limits are read-write, reset_history
is write-only and all the other attributes are read-only.
======================= ==========================================
in0_input VP-VM voltage (mV).
in0_min Undervoltage threshold
in0_max Overvoltage threshold
in0_lowest Lowest measured voltage
in0_highest Highest measured voltage
in0_reset_history Write 1 to reset in1 history
in0_min_alarm Undervoltage alarm
in0_max_alarm Overvoltage alarm
in0_label Channel label (VP-VM)
in1_input DVCC voltage (mV)
in1_min Undervoltage threshold
in1_max Overvoltage threshold
in1_lowest Lowest measured voltage
in1_highest Highest measured voltage
in1_reset_history Write 1 to reset in2 history
in1_min_alarm Undervoltage alarm
in1_max_alarm Overvoltage alarm
in1_label Channel label (DVCC)
curr1_input IP-IM Sense current (mA)
curr1_min Undercurrent threshold
curr1_max Overcurrent threshold
curr1_lowest Lowest measured current
curr1_highest Highest measured current
curr1_reset_history Write 1 to reset curr1 history
curr1_min_alarm Undercurrent alarm
curr1_max_alarm Overcurrent alarm
curr1_label Channel label (IP-IM)
power1_input Power (in uW)
power1_min Low power threshold
power1_max High power threshold
power1_input_lowest Historical minimum power use
power1_input_highest Historical maximum power use
power1_reset_history Write 1 to reset power1 history
power1_min_alarm Low power alarm
power1_max_alarm High power alarm
power1_label Channel label (Power)
temp1_input Chip Temperature (in milliC)
temp1_min Low temperature threshold
temp1_max High temperature threshold
temp1_input_lowest Historical minimum temperature use
temp1_input_highest Historical maximum temperature use
temp1_reset_history Write 1 to reset temp1 history
temp1_min_alarm Low temperature alarm
temp1_max_alarm High temperature alarm
temp1_label Channel label (Ambient)
temp2_min Low temperature threshold for fan control
temp2_max High temperature threshold for fan control
temp2_min_alarm Low temperature fan control alarm
temp2_max_alarm High temperature fan control alarm
temp2_label Channel label (TEMPFAN)
energy1_input Measured energy over time (in microJoule)
energy2_input Measured energy over time (in microJoule)
======================= ==========================================