linux/Documentation/networking/driver.txt
Linus Torvalds 1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00

95 lines
2.7 KiB
Plaintext

Documents about softnet driver issues in general can be found
at:
http://www.firstfloor.org/~andi/softnet/
Transmit path guidelines:
1) The hard_start_xmit method must never return '1' under any
normal circumstances. It is considered a hard error unless
there is no way your device can tell ahead of time when it's
transmit function will become busy.
Instead it must maintain the queue properly. For example,
for a driver implementing scatter-gather this means:
static int drv_hard_start_xmit(struct sk_buff *skb,
struct net_device *dev)
{
struct drv *dp = dev->priv;
lock_tx(dp);
...
/* This is a hard error log it. */
if (TX_BUFFS_AVAIL(dp) <= (skb_shinfo(skb)->nr_frags + 1)) {
netif_stop_queue(dev);
unlock_tx(dp);
printk(KERN_ERR PFX "%s: BUG! Tx Ring full when queue awake!\n",
dev->name);
return 1;
}
... queue packet to card ...
... update tx consumer index ...
if (TX_BUFFS_AVAIL(dp) <= (MAX_SKB_FRAGS + 1))
netif_stop_queue(dev);
...
unlock_tx(dp);
...
}
And then at the end of your TX reclaimation event handling:
if (netif_queue_stopped(dp->dev) &&
TX_BUFFS_AVAIL(dp) > (MAX_SKB_FRAGS + 1))
netif_wake_queue(dp->dev);
For a non-scatter-gather supporting card, the three tests simply become:
/* This is a hard error log it. */
if (TX_BUFFS_AVAIL(dp) <= 0)
and:
if (TX_BUFFS_AVAIL(dp) == 0)
and:
if (netif_queue_stopped(dp->dev) &&
TX_BUFFS_AVAIL(dp) > 0)
netif_wake_queue(dp->dev);
2) Do not forget to update netdev->trans_start to jiffies after
each new tx packet is given to the hardware.
3) Do not forget that once you return 0 from your hard_start_xmit
method, it is your driver's responsibility to free up the SKB
and in some finite amount of time.
For example, this means that it is not allowed for your TX
mitigation scheme to let TX packets "hang out" in the TX
ring unreclaimed forever if no new TX packets are sent.
This error can deadlock sockets waiting for send buffer room
to be freed up.
If you return 1 from the hard_start_xmit method, you must not keep
any reference to that SKB and you must not attempt to free it up.
Probing guidelines:
1) Any hardware layer address you obtain for your device should
be verified. For example, for ethernet check it with
linux/etherdevice.h:is_valid_ether_addr()
Close/stop guidelines:
1) After the dev->stop routine has been called, the hardware must
not receive or transmit any data. All in flight packets must
be aborted. If necessary, poll or wait for completion of
any reset commands.
2) The dev->stop routine will be called by unregister_netdevice
if device is still UP.