linux/drivers/net/usb/cdc_eem.c
Sarah Sharp e1f12eb6ba USB: Disable hub-initiated LPM for comms devices.
Hub-initiated LPM is not good for USB communications devices.  Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.

If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data.  Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.

The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host.  In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.

Set the disable_hub_initiated_lpm flag for for all USB communications
drivers.  I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.

Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
2012-05-18 15:42:55 -07:00

379 lines
9.3 KiB
C

/*
* USB CDC EEM network interface driver
* Copyright (C) 2009 Oberthur Technologies
* by Omar Laazimani, Olivier Condemine
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
*/
#include <linux/module.h>
#include <linux/init.h>
#include <linux/netdevice.h>
#include <linux/etherdevice.h>
#include <linux/ctype.h>
#include <linux/ethtool.h>
#include <linux/workqueue.h>
#include <linux/mii.h>
#include <linux/usb.h>
#include <linux/crc32.h>
#include <linux/usb/cdc.h>
#include <linux/usb/usbnet.h>
#include <linux/gfp.h>
/*
* This driver is an implementation of the CDC "Ethernet Emulation
* Model" (EEM) specification, which encapsulates Ethernet frames
* for transport over USB using a simpler USB device model than the
* previous CDC "Ethernet Control Model" (ECM, or "CDC Ethernet").
*
* For details, see www.usb.org/developers/devclass_docs/CDC_EEM10.pdf
*
* This version has been tested with GIGAntIC WuaoW SIM Smart Card on 2.6.24,
* 2.6.27 and 2.6.30rc2 kernel.
* It has also been validated on Openmoko Om 2008.12 (based on 2.6.24 kernel).
* build on 23-April-2009
*/
#define EEM_HEAD 2 /* 2 byte header */
/*-------------------------------------------------------------------------*/
static void eem_linkcmd_complete(struct urb *urb)
{
dev_kfree_skb(urb->context);
usb_free_urb(urb);
}
static void eem_linkcmd(struct usbnet *dev, struct sk_buff *skb)
{
struct urb *urb;
int status;
urb = usb_alloc_urb(0, GFP_ATOMIC);
if (!urb)
goto fail;
usb_fill_bulk_urb(urb, dev->udev, dev->out,
skb->data, skb->len, eem_linkcmd_complete, skb);
status = usb_submit_urb(urb, GFP_ATOMIC);
if (status) {
usb_free_urb(urb);
fail:
dev_kfree_skb(skb);
netdev_warn(dev->net, "link cmd failure\n");
return;
}
}
static int eem_bind(struct usbnet *dev, struct usb_interface *intf)
{
int status = 0;
status = usbnet_get_endpoints(dev, intf);
if (status < 0) {
usb_set_intfdata(intf, NULL);
usb_driver_release_interface(driver_of(intf), intf);
return status;
}
/* no jumbogram (16K) support for now */
dev->net->hard_header_len += EEM_HEAD + ETH_FCS_LEN;
dev->hard_mtu = dev->net->mtu + dev->net->hard_header_len;
return 0;
}
/*
* EEM permits packing multiple Ethernet frames into USB transfers
* (a "bundle"), but for TX we don't try to do that.
*/
static struct sk_buff *eem_tx_fixup(struct usbnet *dev, struct sk_buff *skb,
gfp_t flags)
{
struct sk_buff *skb2 = NULL;
u16 len = skb->len;
u32 crc = 0;
int padlen = 0;
/* When ((len + EEM_HEAD + ETH_FCS_LEN) % dev->maxpacket) is
* zero, stick two bytes of zero length EEM packet on the end.
* Else the framework would add invalid single byte padding,
* since it can't know whether ZLPs will be handled right by
* all the relevant hardware and software.
*/
if (!((len + EEM_HEAD + ETH_FCS_LEN) % dev->maxpacket))
padlen += 2;
if (!skb_cloned(skb)) {
int headroom = skb_headroom(skb);
int tailroom = skb_tailroom(skb);
if ((tailroom >= ETH_FCS_LEN + padlen) &&
(headroom >= EEM_HEAD))
goto done;
if ((headroom + tailroom)
> (EEM_HEAD + ETH_FCS_LEN + padlen)) {
skb->data = memmove(skb->head +
EEM_HEAD,
skb->data,
skb->len);
skb_set_tail_pointer(skb, len);
goto done;
}
}
skb2 = skb_copy_expand(skb, EEM_HEAD, ETH_FCS_LEN + padlen, flags);
if (!skb2)
return NULL;
dev_kfree_skb_any(skb);
skb = skb2;
done:
/* we don't use the "no Ethernet CRC" option */
crc = crc32_le(~0, skb->data, skb->len);
crc = ~crc;
put_unaligned_le32(crc, skb_put(skb, 4));
/* EEM packet header format:
* b0..13: length of ethernet frame
* b14: bmCRC (1 == valid Ethernet CRC)
* b15: bmType (0 == data)
*/
len = skb->len;
put_unaligned_le16(BIT(14) | len, skb_push(skb, 2));
/* Bundle a zero length EEM packet if needed */
if (padlen)
put_unaligned_le16(0, skb_put(skb, 2));
return skb;
}
static int eem_rx_fixup(struct usbnet *dev, struct sk_buff *skb)
{
/*
* Our task here is to strip off framing, leaving skb with one
* data frame for the usbnet framework code to process. But we
* may have received multiple EEM payloads, or command payloads.
* So we must process _everything_ as if it's a header, except
* maybe the last data payload
*
* REVISIT the framework needs updating so that when we consume
* all payloads (the last or only message was a command, or a
* zero length EEM packet) that is not accounted as an rx_error.
*/
do {
struct sk_buff *skb2 = NULL;
u16 header;
u16 len = 0;
/* incomplete EEM header? */
if (skb->len < EEM_HEAD)
return 0;
/*
* EEM packet header format:
* b0..14: EEM type dependent (Data or Command)
* b15: bmType
*/
header = get_unaligned_le16(skb->data);
skb_pull(skb, EEM_HEAD);
/*
* The bmType bit helps to denote when EEM
* packet is data or command :
* bmType = 0 : EEM data payload
* bmType = 1 : EEM (link) command
*/
if (header & BIT(15)) {
u16 bmEEMCmd;
/*
* EEM (link) command packet:
* b0..10: bmEEMCmdParam
* b11..13: bmEEMCmd
* b14: bmReserved (must be 0)
* b15: 1 (EEM command)
*/
if (header & BIT(14)) {
netdev_dbg(dev->net, "reserved command %04x\n",
header);
continue;
}
bmEEMCmd = (header >> 11) & 0x7;
switch (bmEEMCmd) {
/* Responding to echo requests is mandatory. */
case 0: /* Echo command */
len = header & 0x7FF;
/* bogus command? */
if (skb->len < len)
return 0;
skb2 = skb_clone(skb, GFP_ATOMIC);
if (unlikely(!skb2))
goto next;
skb_trim(skb2, len);
put_unaligned_le16(BIT(15) | (1 << 11) | len,
skb_push(skb2, 2));
eem_linkcmd(dev, skb2);
break;
/*
* Host may choose to ignore hints.
* - suspend: peripheral ready to suspend
* - response: suggest N millisec polling
* - response complete: suggest N sec polling
*/
case 2: /* Suspend hint */
case 3: /* Response hint */
case 4: /* Response complete hint */
continue;
/*
* Hosts should never receive host-to-peripheral
* or reserved command codes; or responses to an
* echo command we didn't send.
*/
case 1: /* Echo response */
case 5: /* Tickle */
default: /* reserved */
netdev_warn(dev->net,
"unexpected link command %d\n",
bmEEMCmd);
continue;
}
} else {
u32 crc, crc2;
int is_last;
/* zero length EEM packet? */
if (header == 0)
continue;
/*
* EEM data packet header :
* b0..13: length of ethernet frame
* b14: bmCRC
* b15: 0 (EEM data)
*/
len = header & 0x3FFF;
/* bogus EEM payload? */
if (skb->len < len)
return 0;
/* bogus ethernet frame? */
if (len < (ETH_HLEN + ETH_FCS_LEN))
goto next;
/*
* Treat the last payload differently: framework
* code expects our "fixup" to have stripped off
* headers, so "skb" is a data packet (or error).
* Else if it's not the last payload, keep "skb"
* for further processing.
*/
is_last = (len == skb->len);
if (is_last)
skb2 = skb;
else {
skb2 = skb_clone(skb, GFP_ATOMIC);
if (unlikely(!skb2))
return 0;
}
/*
* The bmCRC helps to denote when the CRC field in
* the Ethernet frame contains a calculated CRC:
* bmCRC = 1 : CRC is calculated
* bmCRC = 0 : CRC = 0xDEADBEEF
*/
if (header & BIT(14)) {
crc = get_unaligned_le32(skb2->data
+ len - ETH_FCS_LEN);
crc2 = ~crc32_le(~0, skb2->data, skb2->len
- ETH_FCS_LEN);
} else {
crc = get_unaligned_be32(skb2->data
+ len - ETH_FCS_LEN);
crc2 = 0xdeadbeef;
}
skb_trim(skb2, len - ETH_FCS_LEN);
if (is_last)
return crc == crc2;
if (unlikely(crc != crc2)) {
dev->net->stats.rx_errors++;
dev_kfree_skb_any(skb2);
} else
usbnet_skb_return(dev, skb2);
}
next:
skb_pull(skb, len);
} while (skb->len);
return 1;
}
static const struct driver_info eem_info = {
.description = "CDC EEM Device",
.flags = FLAG_ETHER | FLAG_POINTTOPOINT,
.bind = eem_bind,
.rx_fixup = eem_rx_fixup,
.tx_fixup = eem_tx_fixup,
};
/*-------------------------------------------------------------------------*/
static const struct usb_device_id products[] = {
{
USB_INTERFACE_INFO(USB_CLASS_COMM, USB_CDC_SUBCLASS_EEM,
USB_CDC_PROTO_EEM),
.driver_info = (unsigned long) &eem_info,
},
{
/* EMPTY == end of list */
},
};
MODULE_DEVICE_TABLE(usb, products);
static struct usb_driver eem_driver = {
.name = "cdc_eem",
.id_table = products,
.probe = usbnet_probe,
.disconnect = usbnet_disconnect,
.suspend = usbnet_suspend,
.resume = usbnet_resume,
.disable_hub_initiated_lpm = 1,
};
module_usb_driver(eem_driver);
MODULE_AUTHOR("Omar Laazimani <omar.oberthur@gmail.com>");
MODULE_DESCRIPTION("USB CDC EEM");
MODULE_LICENSE("GPL");