linux/arch/arm/mach-omap1/mux.h
Arnd Bergmann 7e0a9e622d ARM: omap1: move mach/*.h into mach directory
Most of the header files are no longer referenced from outside
arch/arm/mach-omap1, so move them all to that place directly
and change their users to use the new location.

The exceptions are:

- mach/compress.h is used by the core architecture code
- mach/serial.h is used by mach/compress.h

The mach/memory.h is empty and gets removed in the process,
avoiding the need for CONFIG_NEED_MACH_MEMORY_H.

Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-04-22 11:08:55 +02:00

145 lines
3.9 KiB
C

/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
* Table of the Omap register configurations for the FUNC_MUX and
* PULL_DWN combinations.
*
* Copyright (C) 2004 - 2008 Texas Instruments Inc.
* Copyright (C) 2003 - 2008 Nokia Corporation
*
* Written by Tony Lindgren
*
* NOTE: Please use the following naming style for new pin entries.
* For example, W8_1610_MMC2_DAT0, where:
* - W8 = ball
* - 1610 = 1510 or 1610, none if common for both 1510 and 1610
* - MMC2_DAT0 = function
*/
#ifndef __ASM_ARCH_MUX_H
#define __ASM_ARCH_MUX_H
#include <linux/soc/ti/omap1-mux.h>
#define PU_PD_SEL_NA 0 /* No pu_pd reg available */
#define PULL_DWN_CTRL_NA 0 /* No pull-down control needed */
#ifdef CONFIG_OMAP_MUX_DEBUG
#define MUX_REG(reg, mode_offset, mode) .mux_reg_name = "FUNC_MUX_CTRL_"#reg, \
.mux_reg = FUNC_MUX_CTRL_##reg, \
.mask_offset = mode_offset, \
.mask = mode,
#define PULL_REG(reg, bit, status) .pull_name = "PULL_DWN_CTRL_"#reg, \
.pull_reg = PULL_DWN_CTRL_##reg, \
.pull_bit = bit, \
.pull_val = status,
#define PU_PD_REG(reg, status) .pu_pd_name = "PU_PD_SEL_"#reg, \
.pu_pd_reg = PU_PD_SEL_##reg, \
.pu_pd_val = status,
#define MUX_REG_7XX(reg, mode_offset, mode) .mux_reg_name = "OMAP7XX_IO_CONF_"#reg, \
.mux_reg = OMAP7XX_IO_CONF_##reg, \
.mask_offset = mode_offset, \
.mask = mode,
#define PULL_REG_7XX(reg, bit, status) .pull_name = "OMAP7XX_IO_CONF_"#reg, \
.pull_reg = OMAP7XX_IO_CONF_##reg, \
.pull_bit = bit, \
.pull_val = status,
#else
#define MUX_REG(reg, mode_offset, mode) .mux_reg = FUNC_MUX_CTRL_##reg, \
.mask_offset = mode_offset, \
.mask = mode,
#define PULL_REG(reg, bit, status) .pull_reg = PULL_DWN_CTRL_##reg, \
.pull_bit = bit, \
.pull_val = status,
#define PU_PD_REG(reg, status) .pu_pd_reg = PU_PD_SEL_##reg, \
.pu_pd_val = status,
#define MUX_REG_7XX(reg, mode_offset, mode) \
.mux_reg = OMAP7XX_IO_CONF_##reg, \
.mask_offset = mode_offset, \
.mask = mode,
#define PULL_REG_7XX(reg, bit, status) .pull_reg = OMAP7XX_IO_CONF_##reg, \
.pull_bit = bit, \
.pull_val = status,
#endif /* CONFIG_OMAP_MUX_DEBUG */
#define MUX_CFG(desc, mux_reg, mode_offset, mode, \
pull_reg, pull_bit, pull_status, \
pu_pd_reg, pu_pd_status, debug_status) \
{ \
.name = desc, \
.debug = debug_status, \
MUX_REG(mux_reg, mode_offset, mode) \
PULL_REG(pull_reg, pull_bit, pull_status) \
PU_PD_REG(pu_pd_reg, pu_pd_status) \
},
/*
* OMAP730/850 has a slightly different config for the pin mux.
* - config regs are the OMAP7XX_IO_CONF_x regs (see omap7xx.h) regs and
* not the FUNC_MUX_CTRL_x regs from hardware.h
* - for pull-up/down, only has one enable bit which is in the same register
* as mux config
*/
#define MUX_CFG_7XX(desc, mux_reg, mode_offset, mode, \
pull_bit, pull_status, debug_status)\
{ \
.name = desc, \
.debug = debug_status, \
MUX_REG_7XX(mux_reg, mode_offset, mode) \
PULL_REG_7XX(mux_reg, pull_bit, pull_status) \
PU_PD_REG(NA, 0) \
},
struct pin_config {
char *name;
const unsigned int mux_reg;
unsigned char debug;
const unsigned char mask_offset;
const unsigned char mask;
const char *pull_name;
const unsigned int pull_reg;
const unsigned char pull_val;
const unsigned char pull_bit;
const char *pu_pd_name;
const unsigned int pu_pd_reg;
const unsigned char pu_pd_val;
#if defined(CONFIG_OMAP_MUX_DEBUG) || defined(CONFIG_OMAP_MUX_WARNINGS)
const char *mux_reg_name;
#endif
};
struct omap_mux_cfg {
struct pin_config *pins;
unsigned long size;
int (*cfg_reg)(const struct pin_config *cfg);
};
#ifdef CONFIG_OMAP_MUX
/* setup pin muxing in Linux */
extern int omap1_mux_init(void);
extern int omap_mux_register(struct omap_mux_cfg *);
#else
/* boot loader does it all (no warnings from CONFIG_OMAP_MUX_WARNINGS) */
static inline int omap1_mux_init(void) { return 0; }
#endif
extern int omap2_mux_init(void);
#endif