Implement a poll controller for netconsole which invokes the RX
interrupt handler to poll for incoming packets, and cleans up all TX
queues by invoking the TX interrupt handler.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement a poll controller for netconsole which invokes both of our
interrupt handlers for the different RX/TX queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 50649ab149 ("stmmac: drop driver from stmmac platform code")
was a bit overzealous in removing code and dropped the MODULE_*
macro's that are still needed since stmmac_platform can be a module.
Fix this by putting the macro's remvoed in 50649ab149 back.
This fixes the following errors when used as a module:
stmmac_platform: module license 'unspecified' taints kernel.
Disabling lock debugging due to kernel taint
stmmac_platform: Unknown symbol devm_kmalloc (err 0)
stmmac_platform: Unknown symbol stmmac_suspend (err 0)
stmmac_platform: Unknown symbol platform_get_irq_byname (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_remove (err 0)
stmmac_platform: Unknown symbol platform_get_resource (err 0)
stmmac_platform: Unknown symbol of_get_phy_mode (err 0)
stmmac_platform: Unknown symbol of_property_read_u32_array (err 0)
stmmac_platform: Unknown symbol of_alias_get_id (err 0)
stmmac_platform: Unknown symbol stmmac_resume (err 0)
stmmac_platform: Unknown symbol stmmac_dvr_probe (err 0)
Fixes: 50649ab149 ("stmmac: drop driver from stmmac platform code")
Reported-by: Igor Gnatenko <i.gnatenko.brain@gmail.com>
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Claudiu Manoil says:
====================
gianfar: wol magic packet fixes
These changes were already validated as part of FSL SDK.
Patch 2 fixes occasional wake-on magic packet failures during
traffic, probably due to incorrect traffic stop/ device halt
sequence and incorrect usage of txlock.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The wol_en flag is 0 by default anyway, and we have the
following inconsistency: a MAGIC packet wol capable eth
interface is registered as a wake-up source but unable
to wake-up the system as wol_en is 0 (wake-on flag set to 'd').
Calling set_wakeup_enable() at netdev open is just redundant
because wol_en is 0 by default.
Let only ethtool call set_wakeup_enable() for now.
The bflock is obviously obsoleted, its utility has been corroded
over time. The bitfield flags used today in gianfar are accessed
only on the init/ config path, with no real possibility of
concurrency - nothing that would justify smth. like bflock.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we disable NAPI in the first place we can mask the device's
interrupts (and halt it) without fearing that imask may be
concurrently accessed from interrupt context, so there's
no need to do local_irq_save() around gfar_halt_nodisable().
lock_rx_qs()/unlock_tx_qs() are just obsoleted and potentially
buggy routines. The txlock is currently used in the driver only
to manage TX congestion, it has nothing to do with halting the
device. With these changes, the TX processing is stopped before
gfar_halt().
Compact gfar_halt() is used instead of gfar_halt_nodisable(),
as it disables Rx/TX DMA h/w blocks and the Rx/TX h/w queues.
gfar_start() re-enables all these blocks on resume. Enabling
the magic-packet mode remains the same, note that the RX block
is re-enabled just before entering sleep mode.
Add IRQF_NO_SUSPEND flag for the error interrupt line, to signal
that the interrupt line must remain active during sleep in order
to wake the system by magic packet (MAG) reception interrupt.
(On some systems the MAG interrupt did trigger w/o this flag
as well, but on others it didn't.)
Without these fixes, when suspended during fair Tx traffic the
interface occasionally failed to be woken up by magic packet.
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC drivers/net/ethernet/freescale/gianfar.o
drivers/net/ethernet/freescale/gianfar.c:568:13: warning: 'lock_tx_qs'
defined but not used [-Wunused-function]
static void lock_tx_qs(struct gfar_private *priv)
^
drivers/net/ethernet/freescale/gianfar.c:576:13: warning: 'unlock_tx_qs'
defined but not used [-Wunused-function]
static void unlock_tx_qs(struct gfar_private *priv)
^
Reported-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tlb_dynamic_lb could be set only via sysfs, this patch allows it to be
set via netlink.
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mwifiex:
* add TX DATA Pause support
* add multichannel and TDLS channel switch support
ath10k:
* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJVu222AAoJEG4XJFUm622biQIH/1A5WVvXw1WbxbnKh3xJmLSZ
OkuSORBl0rbzf0CTtxDax59JqjZaCUZ2MdehKiCFQsv7DKuYk3JnkkvIhSkuTcpX
k4x5CbTIY0MuERtvtsoH+A4hi571jqYprtECRDCZiyDkhNyEnKpKA+ImPXa8HMeQ
iXny9IsH//jtsgcorM2bNcV6QmeUjUozU1jbcRk1pOLd6755ntmI4dRgR0vEpolt
UUEjPEStiaxovXF+dIpEaaANpTggspjku+lFJ1mH6IIyCZMLsnQ3+V/mlFxnPKAA
xFneaOkDYdQYyBAjG7yrPaWWg705Oraamfl2W5a665cOqbfAsUZ+9H0AbHOzSYI=
=99A8
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2015-07-31' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
Major changes:
mwifiex:
* add TX DATA Pause support
* add multichannel and TDLS channel switch support
ath10k:
* enable VHT for IBSS
* initial work to support qca99x0 and the corresponding 10.4 firmware branch
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The policy in the net driver is to attempt MCDI commands and
then handle any EPERM error codes appropriately when returned
by unprivileged functions.
The ethtool selftest contains some tests which are useful on
an unprivileged function, such as the event queue interrupt
tests, but other tests cannot be performed as the function
does not have the required permissions.
If a test returns -EPERM, act as though the test was not run
and continue.
Signed-off-by: Shradha Shah <sshah@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch added driver to support Aquantia PHYs AQ1202, AQ2104, AQR105,
AQR405, which accessed through clause 45.
Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The UEFI driver would enable zero length, and the Linux driver doesn't
need it. Zero length let the hw complete the transfer with length 0,
when there is no received packet. It would add the load of USB host
controller and reduce the performance.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two vxlan driver flags FLOWBASED and COLLECT_METADATA need to be set to
make use of its new flow mode. The former already exposed. Expose the latter.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we share an action within a filter, the bind refcnt
should increase, therefore we should not call tcf_hash_release().
Fixes: 1a29321ed0 ("net_sched: act: Dont increment refcnt on replace")
Cc: Jamal Hadi Salim <jhs@mojatatu.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Cong Wang <cwang@twopensource.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Roopa Prabhu says:
====================
af_mpls: fix undefined reference to ip6_route_output with CONFIG_IPV6=n
This patch series uses ipv6_stub_impl.ipv6_dst_lookup instead of
ip6_route_output. Follows the vxlan drivers usage of
ipv6_stub_impl.ipv6_dst_lookup.
There is no sk in the af_mpls context from where
ipv6_stub_impl.ipv6_dst_lookup is used. sk appears to be needed
to get the namespace 'net' and is optional otherwise. This patch series
changes ipv6_stub_impl.ipv6_dst_lookup to take net argument. sk remains
optional.
v1 - v2: use IS_BUILTIN
v2 - v3: Use new Kconfig option that depends on (IPV6 || IPV6=n) as
suggested by Dave. Also uses IS_ERR as suggested by Thomas.
v3 - v4: Include missed case of (MPLS_ROUTING=y && IPV6=m) reported by
Dave.
v4 - v5: Use ipv6_stub_impl.ipv6_dst_lookup as suggested by Hannes
v5 - v6: protect against null ipv6_stub by statically declaring
a ipv6_dst_lookup NOP func
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Undefined reference to ip6_route_output and ip_route_output
was reported with CONFIG_INET=n and CONFIG_IPV6=n.
This patch uses ipv6_stub_impl.ipv6_dst_lookup instead of
ip6_route_output. And wraps affected code under
IS_ENABLED(CONFIG_INET) and IS_ENABLED(CONFIG_IPV6).
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Reported-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds net argument to ipv6_stub_impl.ipv6_dst_lookup
for use cases where sk is not available (like mpls).
sk appears to be needed to get the namespace 'net' and is optional
otherwise. This patch series changes ipv6_stub_impl.ipv6_dst_lookup
to take net argument. sk remains optional.
All callers of ipv6_stub_impl.ipv6_dst_lookup have been modified
to pass net. I have modified them to use already available
'net' in the scope of the call. I can change them to
sock_net(sk) to avoid any unintended change in behaviour if sock
namespace is different. They dont seem to be from code inspection.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce helpers to let eBPF programs attached to TC manipulate tunnel metadata:
bpf_skb_[gs]et_tunnel_key(skb, key, size, flags)
skb: pointer to skb
key: pointer to 'struct bpf_tunnel_key'
size: size of 'struct bpf_tunnel_key'
flags: room for future extensions
First eBPF program that uses these helpers will allocate per_cpu
metadata_dst structures that will be used on TX.
On RX metadata_dst is allocated by tunnel driver.
Typical usage for TX:
struct bpf_tunnel_key tkey;
... populate tkey ...
bpf_skb_set_tunnel_key(skb, &tkey, sizeof(tkey), 0);
bpf_clone_redirect(skb, vxlan_dev_ifindex, 0);
RX:
struct bpf_tunnel_key tkey = {};
bpf_skb_get_tunnel_key(skb, &tkey, sizeof(tkey), 0);
... lookup or redirect based on tkey ...
'struct bpf_tunnel_key' will be extended in the future by adding
elements to the end and the 'size' argument will indicate which fields
are populated, thereby keeping backwards compatibility.
The 'flags' argument may be used as well when the 'size' is not enough or
to indicate completely different layout of bpf_tunnel_key.
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Repost patch of driver for LAN7800 family of USB 2.0 & USB 3.0 to Gigabit Ethernet.
- remove module param which can be configurable by standard mechanism.
- remove other module parms except msg_level per review comment.
- update to handle byte swap for statistics structure correctly.
Signed-off-by: Woojung Huh <woojung.huh@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to read the dmesg BPF JIT dump also from a
file instead of the klog buffer. I found this quite useful when going
through some 'before/after patch' logs. It also fixes a regex leak
found by valgrind when no image dump was found.
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
These fixes are all for the AMD IOMMU driver:
* A regression with HSA caused by the conversion of the driver to
default domains. The fixes make sure that an HSA device can
still be attached to an IOMMUv2 domain and that these domains
also allow non-IOMMUv2 capable devices.
* Fix iommu=pt mode which did not work because the dma_ops where
set to nommu_ops, which breaks devices that can only do 32bit
DMA.
* Fix an issue with non-PCI devices not working, because there
are no dma_ops for them. This issue was discovered recently as
new AMD x86 platforms have non-PCI devices too.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=amGQ
-----END PGP SIGNATURE-----
Merge tag 'iommu-fixes-v4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
"These fixes are all for the AMD IOMMU driver:
- A regression with HSA caused by the conversion of the driver to
default domains. The fixes make sure that an HSA device can still
be attached to an IOMMUv2 domain and that these domains also allow
non-IOMMUv2 capable devices.
- Fix iommu=pt mode which did not work because the dma_ops where set
to nommu_ops, which breaks devices that can only do 32bit DMA.
- Fix an issue with non-PCI devices not working, because there are no
dma_ops for them. This issue was discovered recently as new AMD
x86 platforms have non-PCI devices too"
* tag 'iommu-fixes-v4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Allow non-ATS devices in IOMMUv2 domains
iommu/amd: Set global dma_ops if swiotlb is disabled
iommu/amd: Use swiotlb in passthrough mode
iommu/amd: Allow non-IOMMUv2 devices in IOMMUv2 domains
iommu/amd: Use iommu core for passthrough mode
iommu/amd: Use iommu_attach_group()
Pull drm intel fixes from Daniel Vetter:
"I delayed my -fixes pull a bit hoping that I could include a fix for
the dp mst stuff but looks a bit more nasty than that. So just 3
other regression fixes, one 4.2 other two cc: stable"
* tag 'drm-intel-fixes-2015-07-31' of git://anongit.freedesktop.org/drm-intel:
drm/i915: Declare the swizzling unknown for L-shaped configurations
drm/i915: Mark PIN_USER binding as GLOBAL_BIND without the aliasing ppgtt
drm/i915: Replace WARN inside I915_READ64_2x32 with retry loop
Pull drm fixes from Dave Airlie:
"This has a bunch of nouveau fixes, as Ben has been hibernating and has
lots of small fixes for lots of bugs across nouveau.
Radeon has one major fix for hdmi/dp audio regression that is larger
than Alex would like, but seems to fix up a fair few bugs, along with
some misc fixes.
And a few msm fixes, one of which is also a bit large.
But nothing in here seems insane or crazy for this stage, just more
than I'd like"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (33 commits)
drm/msm/mdp5: release SMB (shared memory blocks) in various cases
drm/msm: change to uninterruptible wait in atomic commit
drm/msm: mdp4: Fix drm_framebuffer dereference crash
drm/msm: fix msm_gem_prime_get_sg_table()
drm/amdgpu: add new parameter to seperate map and unmap
drm/amdgpu: hdp_flush is not needed for inside IB
drm/amdgpu: different emit_ib for gfx and compute
drm/amdgpu: information leak in amdgpu_info_ioctl()
drm/amdgpu: clean up init sequence for failures
drm/radeon/combios: add some validation of lvds values
drm/radeon: rework audio modeset to handle non-audio hdmi features
drm/radeon: rework audio detect (v4)
drm/amdgpu: Drop drm/ prefix for including drm.h in amdgpu_drm.h
drm/radeon: Drop drm/ prefix for including drm.h in radeon_drm.h
drm/nouveau/nouveau/ttm: fix tiled system memory with Maxwell
drm/nouveau/kms/nv50-: guard against enabling cursor on disabled heads
drm/nouveau/fbcon/g80: reduce PUSH_SPACE alloc, fire ring on accel init
drm/nouveau/fbcon/gf100-: reduce RING_SPACE allocation
drm/nouveau/fbcon/nv11-: correctly account for ring space usage
drm/nouveau/bios: add proper support for opcode 0x59
...
With the grouping of multi-function devices a non-ATS
capable device might also end up in the same domain as an
IOMMUv2 capable device.
So handle this situation gracefully and don't consider it a
bug anymore.
Tested-by: Oded Gabbay <oded.gabbay@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
This reverts commit 6301566e0b. Oleksij Rempel
noticed that the randomness doesn't look to be good enough and Stephan Mueller
commented:
"I would say that the discussed RNG does not seem fit for hooking it up with the
hwrandom framework."
http://lkml.kernel.org/g/3945775.m5HblJPgiO@tauon.atsec.com
So let's the revert the patch until we are sure that we can trust this random
generator.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
- remote attribute log recovery corruption fixes
- DAX page faults need to use direct mappings, not a page cache
mapping.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=kjas
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs
Pull xfs fixes from Dave Chinner:
"There are a couple of recently found, long standing remote attribute
corruption fixes caused by log recovery getting confused after a
crash, and the new DAX code in XFS (merged in 4.2-rc1) needs to
actually use the DAX fault path on read faults.
Summary:
- remote attribute log recovery corruption fixes
- DAX page faults need to use direct mappings, not a page cache
mapping"
* tag 'xfs-for-linus-4.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/dgc/linux-xfs:
xfs: remote attributes need to be considered data
xfs: remote attribute headers contain an invalid LSN
xfs: call dax_fault on read page faults for DAX
Jon Maloy says:
====================
tipc: separate link aggregation from link layer
We continue the work on separating the roles of the link aggregation and
link layers, as well as making code cleanups in general.
This second commit batch focuses on moving the orchestration of link
failover and synchronization to the node level, as well as preparing the
node lock structure for further future impovements. We also make some
changes to message delivery between link and socket layer, in order to
make this mechanism safer and less obscure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We simplify the link creation function tipc_link_create() and the way
the link struct it is connected to the node struct. In particular, we
remove the duplicate initialization of some fields which are anyway set
in tipc_link_reset().
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently, when we extract small messages from a message bundle, or
when many messages have accumulated in the link arrival queue, those
messages are added one by one to the lock protected link input queue.
This may increase contention with the reader of that queue, in
the function tipc_sk_rcv().
This commit introduces a temporary, unprotected input queue in
tipc_link_rcv() for such cases. Only when the arrival queue has been
emptied, and the function is ready to return, does it splice the whole
temporary queue into the real input queue.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After the most recent changes, all access calls to a link which
may entail addition of messages to the link's input queue are
postpended by an explicit call to tipc_sk_rcv(), using a reference
to the correct queue.
This means that the potentially hazardous implicit delivery, using
tipc_node_unlock() in combination with a binary flag and a cached
queue pointer, now has become redundant.
This commit removes this implicit delivery mechanism both for regular
data messages and for binding table update messages.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to facilitate future improvements to the locking structure, we
want to make resetting and establishing of links non-atomic. I.e., the
functions tipc_node_link_up() and tipc_node_link_down() should be called
from outside the node lock context, and grab/release the node lock
themselves. This requires that we can freeze the link state from the
moment it is set to RESETTING or PEER_RESET in one lock context until
it is set to RESET or ESTABLISHING in a later context. The recently
introduced link FSM makes this possible, so we are now ready to introduce
the above change.
This commit implements this.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The node lock is currently grabbed and and released in the function
tipc_disc_rcv() in the file discover.c. As a preparation for the next
commits, we need to move this node lock handling, along with the code
area it is covering, to node.c.
This commit introduces this change.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, we have been handling link failover and synchronization
by using an additional link state variable, "exec_mode". This variable
is not independent of the link FSM state, something causing a risk of
inconsistencies, apart from the fact that it clutters the code.
The conditions are now in place to define a new link FSM that covers
all existing use cases, including failover and synchronization, and
eliminate the "exec_mode" field altogether. The FSM must also support
non-atomic resetting of links, which will be introduced later.
The new link FSM is shown below, with 7 states and 8 events.
Only events leading to state change are shown as edges.
+------------------------------------+
|RESET_EVT |
| |
| +--------------+
| +-----------------| SYNCHING |-----------------+
| |FAILURE_EVT +--------------+ PEER_RESET_EVT|
| | A | |
| | | | |
| | | | |
| | |SYNCH_ |SYNCH_ |
| | |BEGIN_EVT |END_EVT |
| | | | |
| V | V V
| +-------------+ +--------------+ +------------+
| | RESETTING |<---------| ESTABLISHED |--------->| PEER_RESET |
| +-------------+ FAILURE_ +--------------+ PEER_ +------------+
| | EVT | A RESET_EVT |
| | | | |
| | | | |
| | +--------------+ | |
| RESET_EVT| |RESET_EVT |ESTABLISH_EVT |
| | | | |
| | | | |
| V V | |
| +-------------+ +--------------+ RESET_EVT|
+--->| RESET |--------->| ESTABLISHING |<----------------+
+-------------+ PEER_ +--------------+
| A RESET_EVT |
| | |
| | |
|FAILOVER_ |FAILOVER_ |FAILOVER_
|BEGIN_EVT |END_EVT |BEGIN_EVT
| | |
V | |
+-------------+ |
| FAILINGOVER |<----------------+
+-------------+
These changes are fully backwards compatible.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The implementation of the link FSM currently takes decisions about and
sends out link protocol messages. This is unnecessary, since such
actions are not the result of any link state change, and are even
decided based on non-FSM state information ("silent_intv_cnt").
We now move the sending of unicast link protocol messages to the
function tipc_link_timeout(), and the initial broadcast synchronization
message to tipc_node_link_up(). The latter is done because a link
instance should not need to know whether it is the first or second
link to a destination. Such information is now restricted to and
handled by the link aggregation layer in node.c
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Link failover and synchronization have until now been handled by the
links themselves, forcing them to have knowledge about and to access
parallel links in order to make the two algorithms work correctly.
In this commit, we move the control part of this functionality to the
link aggregation level in node.c, which is the right location for this.
As a result, the two algorithms become easier to follow, and the link
implementation becomes simpler.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In many cases the call order when a link is reset goes as follows:
tipc_node_xx()->tipc_link_reset()->tipc_node_link_down()
This is not the right order if we want the node to be in control,
so in this commit we change the order to:
tipc_node_xx()->tipc_node_link_down()->tipc_link_reset()
The fact that tipc_link_reset() now is called from only one
location with a well-defined state will also facilitate later
simplifications of tipc_link_reset() and the link FSM.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In line with our effort to let the node level have full control over
its links, we want to move all link reset calls from link.c to node.c.
Some of the calls can be moved by simply moving the calling function,
when this is the right thing to do. For the remaining calls we use
the now established technique of returning a TIPC_LINK_DOWN_EVT
flag from tipc_link_rcv(), whereafter we perform the reset call when
the call returns.
This change serves as a preparation for the coming commits.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function tipc_link_activate() is redundant, since it mostly performs
settings that have already been done in a preceding tipc_link_reset().
There are three exceptions to this:
- The actual state change to TIPC_LINK_WORKING. This should anyway be done
in the FSM, and not in a separate function.
- Registration of the link with the bearer. This should be done by the
node, since we don't want the link to have any knowledge about its
specific bearer.
- Call to tipc_node_link_up() for user access registration. With the new
role distribution between link aggregation and link level this becomes
the wrong call order; tipc_node_link_up() should instead be called
directly as a result of a TIPC_LINK_UP event, hence by the node itself.
This commit implements those changes.
Tested-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: Jon Maloy <jon.maloy@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2015-07-30
Here's a set of Bluetooth & 802.15.4 patches intended for the 4.3 kernel.
- Cleanups & fixes to mac802154
- Refactoring of Intel Bluetooth HCI driver
- Various coding style fixes to Bluetooth HCI drivers
- Support for Intel Lightning Peak Bluetooth devices
- Generic class code in interface descriptor in btusb to match more HW
- Refactoring of Bluetooth HS code together with a new config option
- Support for BCM4330B1 Broadcom UART controller
Let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The newsk returned by sk_clone_lock should hold a get_net()
reference if, and only if, the parent is not a kernel socket
(making this similar to sk_alloc()).
E.g,. for the SYN_RECV path, tcp_v4_syn_recv_sock->..inet_csk_clone_lock
sets up the syn_recv newsk from sk_clone_lock. When the parent (listen)
socket is a kernel socket (defined in sk_alloc() as having
sk_net_refcnt == 0), then the newsk should also have a 0 sk_net_refcnt
and should not hold a get_net() reference.
Fixes: 26abe14379 ("net: Modify sk_alloc to not reference count the
netns of kernel sockets.")
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sowmini Varadhan <sowmini.varadhan@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6fd99094de ("ipv6: Don't reduce hop limit for an interface")
disabled accept hop limit from RA if it is smaller than the current hop
limit for security stuff. But this behavior kind of break the RFC definition.
RFC 4861, 6.3.4. Processing Received Router Advertisements
A Router Advertisement field (e.g., Cur Hop Limit, Reachable Time,
and Retrans Timer) may contain a value denoting that it is
unspecified. In such cases, the parameter should be ignored and the
host should continue using whatever value it is already using.
If the received Cur Hop Limit value is non-zero, the host SHOULD set
its CurHopLimit variable to the received value.
So add sysctl option accept_ra_min_hop_limit to let user choose the minimum
hop limit value they can accept from RA. And set default to 1 to meet RFC
standards.
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: YOSHIFUJI Hideaki <hideaki.yoshifuji@miraclelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since commit 55334a5db5 ("net_sched: act: refuse to remove bound action
outside"), we end up with a wrong reference count for a tc action.
Test case 1:
FOO="1,6 0 0 4294967295,"
BAR="1,6 0 0 4294967294,"
tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 \
action bpf bytecode "$FOO"
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
index 1 ref 1 bind 1
tc actions replace action bpf bytecode "$BAR" index 1
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967294' default-action pipe
index 1 ref 2 bind 1
tc actions replace action bpf bytecode "$FOO" index 1
tc actions show action bpf
action order 0: bpf bytecode '1,6 0 0 4294967295' default-action pipe
index 1 ref 3 bind 1
Test case 2:
FOO="1,6 0 0 4294967295,"
tc filter add dev foo parent 1: bpf bytecode "$FOO" flowid 1:1 action ok
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 1 bind 1
tc actions add action drop index 1
RTNETLINK answers: File exists [...]
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 2 bind 1
tc actions add action drop index 1
RTNETLINK answers: File exists [...]
tc actions show action gact
action order 0: gact action pass
random type none pass val 0
index 1 ref 3 bind 1
What happens is that in tcf_hash_check(), we check tcf_common for a given
index and increase tcfc_refcnt and conditionally tcfc_bindcnt when we've
found an existing action. Now there are the following cases:
1) We do a late binding of an action. In that case, we leave the
tcfc_refcnt/tcfc_bindcnt increased and are done with the ->init()
handler. This is correctly handeled.
2) We replace the given action, or we try to add one without replacing
and find out that the action at a specific index already exists
(thus, we go out with error in that case).
In case of 2), we have to undo the reference count increase from
tcf_hash_check() in the tcf_hash_check() function. Currently, we fail to
do so because of the 'tcfc_bindcnt > 0' check which bails out early with
an -EPERM error.
Now, while commit 55334a5db5 prevents 'tc actions del action ...' on an
already classifier-bound action to drop the reference count (which could
then become negative, wrap around etc), this restriction only accounts for
invocations outside a specific action's ->init() handler.
One possible solution would be to add a flag thus we possibly trigger
the -EPERM ony in situations where it is indeed relevant.
After the patch, above test cases have correct reference count again.
Fixes: 55334a5db5 ("net_sched: act: refuse to remove bound action outside")
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Reviewed-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The change removes redundant sysfs binary file boundary checks,
since this task is already done on caller side in fs/sysfs/file.c
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hayes Wang says:
====================
r8152: device reset
v3:
For patch #2, remove cancel_delayed_work().
v2:
For patch #1, remove usb_autopm_get_interface(), usb_autopm_put_interface(), and
the checking of intf->condition.
For patch #2, replace the original method with usb_queue_reset_device() to reset
the device.
v1:
Although the driver works normally, we find the device may get all 0xff data when
transmitting packets on certain platforms. It would break the device and no packet
could be transmitted. The reset is necessary to recover the hw for this situation.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The device reset is necessary if the hw becomes abnormal and stops
transmitting packets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rtl8152_pre_reset() and rtl8152_post_reset() which are used when
calling usb_reset_device(). The two functions could reduce the time
of reset when calling usb_reset_device() after probe().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MacBook Pro 5,2 with ALC889 codec had already a fixup entry, but this
seems not working correctly, a fix for pin NID 0x15 is needed in
addition. It's equivalent with the fixup for MacBook Air 1,1, so use
this instead.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=102131
Reported-and-tested-by: Jeffery Miller <jefferym@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>