This will add the board name to the machine entry in /proc/cpuinfo.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5864/
Fix nvram_read_alpha2 copying too many bytes over the ssb_sprom
structure. Also fix the arguments of the read_macaddr, although the code
was technically not wrong before due to an extra dereference.
Signed-off-by: Ilia Mirkin <imirkin@alum.mit.edu>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6211/
This adds support for vectored interrupt which is supported by the SoC
using a MIPS 74K CPU like the BCM4716 and BCM4706.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6290/
Move the possible nvram sizes from the stack into the data segment
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6044/
plat_irq_dispatch() is called from asm code, add asmlinkage.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6043/
The BCM47xx SoCs have a 8250 serial compatible console at address
0x18000300 and an other at 0x18000400. On most devices 0x18000300 is
wired to some pins on the board, we should use that.
This is the smae for the AI (bcma) and the SB (ssb) bus, this is some
offset on the chip common core.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5889/
bcm47xx only uses the CFE code for early print to a console, but that
is also possible with a early print serial 8250 driver.
The CFE api init causes hangs somewhere in prom_init_cfe() on some
devices like the Buffalo WHR-HP-G54 and the Asus WL-520GU.
This was reported in https://dev.openwrt.org/ticket/4061 and
https://forum.openwrt.org/viewtopic.php?id=17063
This will remove all the CFE handling code from bcm47xx.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5888/
Recently the output of "system type" in /proc/cpuinfo was changed to
Broadcom BCM4730 (Some sample board), but it is better to just print
the SoC name in the "system type" entry. The board name will be added
in the machine entry later.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5865/
Let BCM47XX_SSB select the appropriate BMIPS CPUs enountered on those
systems.
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6244/
The ADM6996L switch and some Broadcom switches with two MII interfaces
like the BCM5325F connected to two MACs on the SoC, used on some
routers do not return a valid value when reading the PHY id register
and Linux thinks there is no PHY at all, but that is wrong.
This patch registers a fixed phy in the arch code and then searches it
when there is no other phy in the Ethernet driver code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Asus WL520GC and WL520GU are based on the BCM5354 and clocked at
200MHz, but they do not have a clkfreq nvram variable set to the
correct value. This adds a workaround for these devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5843/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some BCM5354 SoCs are running at 200MHz, but it is not possible to read
the clock from a register like it is done on some other SoC in ssb and
bcma. These devices should have a clkfreq nvram configuration value set
to 200, read it and set the clock to the correct value.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5842/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The nvram contains some gpio configuration for boards. It is stored in
a gpio<number>=name format e.g.
gpio8=wps_button
gpio4=robo_reset
This patches adds a function to parse these entries, so other driver
can use it.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Do not print the constant system type "Broadcom BCM47XX" but print the
name of the actual SoC in use and the detected board.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5839/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Detect on which board this code is running based on some nvram
settings. This is needed to start board specific workarounds and
configure the leds and buttons which are on different gpios on every board.
This patches add some boards we have seen, but there are many more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5840
Patchwork: https://patchwork.linux-mips.org/patch/5855/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If neither BCM47XX_SSD nor BCM47XX_BCMA is selected, then no
CPU type is available leading to build problems. We fix
this problem by using MIPS32r1 as the default CPU type for
the BCM47XX platform.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Acked-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5618/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Conflicts:
include/linux/ssb/ssb_driver_gige.h
Also resolves a logical merge conflict in drivers/net/ethernet/broadcom/-
bgmac.c due to change of an API.
An SoC normally do not define path variables for board_rev and
board_type and the Broadcom SDK also uses the nvram values without a
prefix in such cases. Do the same to fill these sprom attributes from
nvram and do not leave them empty, because brcmsmac do not like this.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4679/
Signed-off-by: John Crispin <blogic@openwrt.org>
Some nvram values on some devices have a newline character at the end
of the value, that caused read errors. Trim the string before reading
the number.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4745/
Signed-off-by: John Crispin <blogic@openwrt.org>
The nvram functions are exported and used by some normal drivers. To
prevent name clashes with ofter parts of the kernel code add a bcm47xx_
prefix in front of the function names and the header file name.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4744/
Signed-off-by: John Crispin <blogic@openwrt.org>
The old code just worked for nvram with a size of 0x8000 bytes. This
patch adds support for reading nvram from partitions of 0xF000 and
0x10000 bytes.
There is just 32KB space for the nvram, but most devices do not use the
full size and this code reads the first 32KB in that case and prints a
warning.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4743/
Signed-off-by: John Crispin <blogic@openwrt.org>
This makes it possible to handle the case of not being able to read the
nvram ram. This could happen when the code searching for the specific
flash chip have not run jet.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4740/
Signed-off-by: John Crispin <blogic@openwrt.org>
Instead of using our own error codes use some common codes.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4739/
Signed-off-by: John Crispin <blogic@openwrt.org>
Also check if parallel flash is present at all before accessing it and
add support for serial flash on BCMA bus.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4738/
Signed-off-by: John Crispin <blogic@openwrt.org>
Synchronize with 'net' in order to sort out some l2tp, wireless, and
ipv6 GRE fixes that will be built on top of in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Having received another series of whitespace patches I decided to do this
once and for all rather than dealing with this kind of patches trickling
in forever.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Kconfig items BCM47XX_BCMA and BCM47XX_SSB selected respectively
BCMA_DRIVER_GPIO and SSB_DRIVER_GPIO. These options depend on GPIOLIB
without explicitly selecting it so it results in a warning when GPIOLIB
is not set:
scripts/kconfig/conf --oldconfig Kconfig
warning: (BCM47XX_BCMA) selects BCMA_DRIVER_GPIO ... unmet direct
dependencies (BCMA_POSSIBLE && BCMA && GPIOLIB)
warning: (BCM47XX_SSB) selects SSB_DRIVER_GPIO ... unmet direct
dependencies (SSB_POSSIBLE && SSB && GPIOLIB)
which subsequently results in compile errors.
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4759/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The irq signal numbers that are send by the cpu are increased by 2 from
the number programmed into the mips core by bcma.
Return the irq number on which the irqs are send in bcma_core_irq() now.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
Instated of providing an own GPIO driver use the one provided by ssb and
bcma.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4592
Acked-by: Florian Fainelli <florian@openwrt.org>
There are bcma based devices like the Linksys E2000 out there, which do
have one ieee80211 core, but no PCIe core and they are using no
prefixes for the sprom. In addition some values like boardtype are
stored without a prefix for the main SoC chip also when they have an
additional PCIe wifi chip with an own boardtype var on some devices.
The Ethernet addresses are now also read out correctly without a prefix
so calling bcm47xx_fill_sprom_ethernet is not needed any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4364
Signed-off-by: John Crispin <blogic@openwrt.org>
If there is no ieee80211 core on the devices like on the BCM4706 read
out the sprom and the other data without using a prefix.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4361
Signed-off-by: John Crispin <blogic@openwrt.org>
Read out the full board data independently of the sprom version. Now we
also get the full boardflags and so on if sromrev is not set and our
code would assume a rev 1 device. When a nvram option is not set
because it is not there this is no problem.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4363
Signed-off-by: John Crispin <blogic@openwrt.org>
The memory size is detected by finding a place where it repeats in
memory. Currently we are just checking when the function prom_init is
seen again, but it is better to check for a bigger part of the memory
to decrease the chance of wrong results.
This should fix a problem we saw in OpenWrt, where the detected
available memory decreed on some devices when doing a soft reboot.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4362
Signed-off-by: John Crispin <blogic@openwrt.org>
Ignoring the last page when ddr size is 128M. Cached accesses to last
page is causing the processor to prefetch using address above 128M
stepping out of the ddr address space.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/4365
Signed-off-by: John Crispin <blogic@openwrt.org>
This is a preparing step for adding serial flash support.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The first thing bcm47xx_fill_sprom does is initialize (zero fill) the SPROM. For
BCMA SOC, this wipes out any values previously read by bcm47xx_fill_sprom_ethernet
(see arch/mips/bcm47xx/setup.c - bcm47xx_get_sprom_bcma). Move the initialization
of SPROM so it is called prior to filling in any values.
Signed-off-by: Nathan Hintz <nlhintz@hotmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the boardrev with a prefix is not available, try to read it
without a prefix. This is based on code from the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This struct contains information about the board, the chip is running
on. The struct is filled for PCIe devices and SoCs. This information is
used by b43 and will be used by brcmsmac soon.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now the fetching of board data also uses nvram_read_u16 and not
simple_strtoul any more.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Previously the rev contained the revision read from the pci config
space and was used as board_rev in the wireless drivers. This is wrong
the board_rev is only fetched from the sprom accordingly to the open
source part of the Broadcom SDK and brcmsmac. This patch removes the
rev from the boardinfo structure and uses the board_rev attribute from
sprom instead. This attribute is filled by PCI, PCMCIA, SDIO and SoC
code.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Tested-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On SoCs the sprom is often stored in nvram in the flashchip. This patch
registers a sprom fallback callback handler in bcma and provides the
sprom needed for this device.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the sprom parsing from nvram into sprom.c. There are all values
needed for sprom version 1 to 9 read from nvram and there are more
sanity checks added. This is based on the sprom parsing in the open
source part of the Broadcom SDK.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Panic() invokes printk() to add a \n internally, so panic arguments should
not themselves end in \n. Panic invocations in arch/mips and elsewhere
are inconsistently sometimes terminating in \n, sometimes not.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Or else we get lots of variations on this:
arch/mips/pci/pci.c:330: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
scattered throughout the build.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
This patch add support for the bcma bus. Broadcom uses only Mips 74K
CPUs on the new SoC and on the old ons using ssb bus there are no Mips
74K CPUs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prepare bcm47xx to support different System buses. Before adding
support for bcma it should be possible to build bcm47xx without the
need of ssb. With this patch bcm47xx does not directly contain a
ssb_bus, but a union contain all the supported system buses. As a SoC
just uses one system bus a union is a good choice.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some members of the struct ssb_sprom where not filled with data available
in the NVRAM. Some attribute names in the NVRAM changed from SPROM version
3 to version 4. This patch was done by analyzing the the pci sprom parser
in the ssb code and some open source parts of the braodcom wireless driver
used on embedded devices.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2365/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are generating the prefix based on the PCI bus address the device is
on. This is done like Broadcom does it in their code expect that the the
bus number is increased by one. In the SB bus implementation used by
Broadcom the SB bus emulates a PCI bus so the kernel sees one PCI bus
more then in our implementation. We do not handle prefixes like sb/1/
yet as they are only used on the new bus which is not implemented yet.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2364/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When an other SSB based device without an own SPROM is attached, using the
PCI bus to the main SSB based device, the data normally found in the SPROM
will be stored in the NVRAM on modern devices. The keys, to load the data
from the NVRAM, are all using some sort of prefix like pci/1/1/, pci/1/3/
or sb/1/ before the actual key. This patch extends bcm47xx_fill_sprom() to
make it possible to read out these values when some prefix was used.
The keys for the SPROM data used on the main chip does not have a prefix.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2363/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some devices like the Netgear WGT634U are using ttyS1 for default console
output. We should switch to that console if it was given in the kernel_args
parameters.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1848/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of writing own function for parsing the mac address we now
use sscanf.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1847/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fill the sprom with all available values from the nvram. Most of these
new values are needed for the b43 or b43legacy driver.
Parts of this patch have been in OpenWRT for a long time and were written
by Michael Buesch.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1846/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The config options read out here are not stored in CFE but only in NVRAM on
the devices. Remove reading from CFE and only access the NVRAM. Reading out
CFE does not harm but is useless here.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: https://patchwork.linux-mips.org/patch/1845/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nvram_getenv should behave like cfe_getenv. cfe_getenv returns 0 on
success and -9 if the value was not found. If the input was wrong -8
will be returned by cfe_getenv. Change nvram_getenv to do the same.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Waldemar Brodkorb <wbx@openadk.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1520/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The previous patch 4a86f2d27733f610e642649aca3e82e86fca9e22 (lmo) rsp.
84a6fcb368 (kernel.org) was wrong.
The BCM47xx architecture maps the ram into a 128MB address space. It
will be spaced there as often as goes into the 128MB. Detection tries to
find the position where the same memory is found. When reading beyond
128MB the processor will throw an exception. If 128MB RAM is installed,
it will not find a memory alias because it tries to read beyond the 128MB
border. Now it just assumes 128MB installed ram if it can not find an
alias.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1508/
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When trying to netboot a Linksys WRT54GS WLAN router, the bootup fails,
because of following error message:
...
[ 0.424000] b44: b44.c:v2.0
[ 0.424000] b44: Invalid MAC address found in EEPROM
[ 0.432000] b44 ssb0:1: Problem fetching invariants of chip,aborting
[ 0.436000] b44: probe of ssb0:1 failed with error -22
...
The router uses a CFE bootloader, but most of the needed environment
variables for network card initialization, are not available from CFE
via printenv and even though not via cfe_getenv().
The required environment variables are saved in a special partition
in flash memory. The attached patch implement nvram_getenv and enables
bootup via NFS root on my router.
Most of the patch is extracted from the OpenWrt subversion repository and
stripped down and cleaned up to just fix this issue.
[Ralf: sorted out header file inclusions. Lots of unneded headers and such
that should have been included.]
Signed-off-by: Waldemar Brodkorb <wbx@openadk.org>
Reviewed-by: Phil Sutter <phil@nwl.cc>
To: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Patchwork: http://patchwork.linux-mips.org/patch/1359/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Ignoring the last page when ddr size is 128M. Cached accesses to last page
is causing the processor to prefetch using address above 128M stepping out
of the DDR address space.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/981/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS-specific macro CL_SIZE is merely aliasing the macro
COMMAND_LINE_SIZE. Other architectures use the latter; also,
COMMAND_LINE_SIZE is documented in kernel-parameters.txt, so
let's use it, and remove the alias.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit 22242681cf ("MIPS: Extend
COMMAND_LINE_SIZE"), CL_SIZE is 4096 and local array variables with this
size will cause an build failure with default CONFIG_FRAME_WARN settings.
Although current users of such array variables are all early bootstrap
code and not likely to cause real stack overflow (thread_info corruption),
it is preferable to to declare these arrays static with __initdata.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the reset button of WGT634U machine, using
GPIO interrupts. Based on a patch from Michel Lespinasse.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch simplifies the BCM47xx GPIO code by using the new SSB GPIO
API, which does a lot things that were implemented directly in the
BCM47xx code.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds a printk message when a WGT634U machine is detected.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Switch the BCM47XX code to the new SPROM data structure now that the old
one has been removed.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Hard to follow who is pointing what to where and why so it's simply getting
in the way of the time code renovation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add LED support to the WGT634U machine. It uses the new gpio-led
driver and a platform driver for the pin definitions.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add GPIO support to the BCM47XX platform. It will be used by a GPIO
LED driver.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add CFE support to the BCM47XX code. That includes querying CFE environment
variables as well as using CFE to print messages before the serial port is
initialized (early printk).
Signed-off-by: Aurelien Jarno <aurel32@farad.aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Note that the BCM4710 does not support the wait instruction, this
is not a mistake in the code.
It originally comes from the OpenWrt patches.
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Florian Schirmer <jolt@tuxbox.org>
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
