Replace the for() loop that traverses all the TX queues on an EQ
with the macro for_all_tx_queues_on_eq(). With this expalnatory
name, the one line comment is not required anymore.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enforcing a budget on the TX completion processing in NAPI doesn't
benefit performance in anyway. Just get rid of it.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are a few failure cases in be_cmd_get_regs() that ideally must return
an error value. This style is used across all the routines in be_cmds.c with
this routine being an exception. This patch fixes this.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch defines a new macro BE_MAX_MTU to make the code in be_change_mtu()
more readable.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In cases where there is no extra code to handle an error, this patch replaces
gotos with a direct return statement.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Log messages in the Lancer FW download path have issues such as:
- a single message spanning multiple lines
- the success message is logged even in failure cases
- status codes are already logged in the FW cmd routines
This patch fixes these issues.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a dma_mapping_error counter to count the number of packets dropped
due to DMA mapping errors.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
HW reports TX completion errors in TX completion. This patch adds these
counters to ethtool statistics.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AMAP_GET/SET_BITS() macro calls take structure name as a parameter
and hence are long and span more than one line. Replace these calls
with a wrapper macros for RX/Tx compls and TX wrb. This results in fewer
lines and more readable code in be_main.c
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the following log messages to help debugging
failure cases:
1) log FW version number: this is useful when driver initialization
fails and the FW version number cannot be queried via ethtool
2) per function resource limits for BEx chips: these values are
currently being printed only for Skyhawk and Lancer
3) PCI BAR mapping failure
4) function_mode/caps queried from FW: this helps catch any FW bugs
that could advertise wrong capabilities to the driver
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of RDMA-related called to t4_query_params() were issuing mbox commands
on mbox0 instead of mbox4.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid dumping MPS_RPLC_MAP_CTL for reg dumps; this is a Write-Only register.
Reading this register may cause MPS TCAM corruption.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The adapter firmware can indicate error conditions to the host.
If the firmware has indicated an error, print out the reason for
the firmware error.
Based on original work by Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes few register access for both T4 and T5.
PCIE_CORE_UTL_SYSTEM_BUS_AGENT_STATUS & PCIE_CORE_UTL_PCI_EXPRESS_PORT_STATUS
is T4 only register don't let T5 access them. For T5 MA_PARITY_ERROR_STATUS2
is additionally read. MPS_TRC_RSS_CONTROL is T4 only register, for T5 use
MPS_T5_TRC_RSS_CONTROL.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously it was using the length value of serial number.
Also added macro for VPD unique identifier (0x82).
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We previously assumed that a Port's Capabilities and Advertised Capabilities
would never change from Port Initialization time. This is no longer true
when we can have 10Gb/s and 1Gb/s SFP+ Transceiver Modules randomly swapped.
Signed-off-by: Hariprasad Shenai <hariprasad@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of the HW is not able to do the receive checksum offloading
the only feature to remove is NETIF_F_RXCSUM.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For new GMACs it is possible to turn-on/off the COE.
In the current driver, when disabled the Rx-checksum
via ethtool, the tool reported that csum was disabled
but the HW continued to set the IPC. Indeed this is
because the fix_features allows this. So the patch
fixes this problem by adding the set_features.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When configuring Tx flow control the Rx queue count was used instead of
the Tx queue count for looping through the Tx hardware queues. Fix the
code to use the Tx queue count.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The debugfs support for the xpcs registers did not properly use the
specified mmd (xpcs_mmd entry) which resulted in the default mmd
value always being used. Update the debugfs support to generate the
proper mmd register value.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fifo size reported by the hardware is not correct. Add support
to limit the reported size to what is actually present. Also, fix
the argument types used in the fifo size calculation function.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The flushing of the Tx hardware queues is only supported at a certain
level of the hardware. Retrieve the current version of the hardware
and use that to determine if flushing is supported.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If NO_DMA=y:
drivers/built-in.o: In function `xgene_enet_delete_ring':
xgene_enet_main.c:(.text+0x28755a): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `xgene_enet_setup_tx_desc':
xgene_enet_main.c:(.text+0x287774): undefined reference to `dma_map_single'
xgene_enet_main.c:(.text+0x287780): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `xgene_enet_tx_completion':
xgene_enet_main.c:(.text+0x2878e6): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `xgene_enet_refill_bufpool':
xgene_enet_main.c:(.text+0x2879d4): undefined reference to `dma_map_single'
xgene_enet_main.c:(.text+0x2879e0): undefined reference to `dma_mapping_error'
drivers/built-in.o: In function `xgene_enet_rx_frame':
xgene_enet_main.c:(.text+0x287aaa): undefined reference to `dma_unmap_single'
drivers/built-in.o: In function `xgene_enet_free_desc_ring':
xgene_enet_main.c:(.text+0x287f98): undefined reference to `dma_free_coherent'
drivers/built-in.o: In function `xgene_enet_create_desc_ring':
xgene_enet_main.c:(.text+0x28808e): undefined reference to `dma_alloc_coherent'
drivers/built-in.o: In function `xgene_enet_probe':
xgene_enet_main.c:(.text+0x2883d4): undefined reference to `dma_set_mask'
xgene_enet_main.c:(.text+0x2883ec): undefined reference to `dma_supported'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When Broadcom tags are enabled, e.g: when interfaced to an Ethernet
switch, make sure that we tell the RXCHK engine that it should be
expecting a 4-bytes Broadcom tag after the Ethernet MAC Source Address.
Use netdev_uses_dsa() to check for that condition since that will tell
us if a switch is attached to our network interface.
Fixes: 80105befdb ("net: systemport: add Broadcom SYSTEMPORT Ethernet MAC driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set correct bit for packed description.
Introduced in e42780b66a
bnx2x: Utilize FW 7.10.51
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes incorrectly defined struct in FW HSI for BE platform.
Affects tunneling, tx-switching and anti-spoofing.
Introduced in e42780b66a
bnx2x: Utilize FW 7.10.51
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of PLS is active the PLS (PHY Link Status) bit in
the Reg12 has to be set to allow the MAC to asserts the LPI
pattern when the link is ok.
Signed-off-by: nandini sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to skip the EEE initialisation when the stmmac
is using a switch (with a fixed phy support).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The value for LPI TW timer has to be updated to 0x1E that is the hardcoded value
of 20.5us and it will apply to all EEE enabled Remote PHYs.
Disadvantage is for PHY's that support lesser wakeup time but we can accept it
waiting to implement LLDP to negotiate the Wakeup time of Remote PHY.
Signed-off-by: nandini sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the definition of macros for EEE otherwise the LPI TX/RX
entry/exit cannot be properly managed.
Signed-off-by: Nandini Sharma <nandini.sharma@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Warning:
drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c:122:41:
sparse: cast removes address space of expression
drivers/net/ethernet/stmicro/stmmac/dwmac-socfpga.c:122:38:
sparse: incorrect type in assignment (different address spaces)
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set skb->csum_level instead of skb->encapsulation when indicating
CHECKSUM_UNNECESSARY for an encapsulated checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set skb->csum_level instead of skb->encapsulation when indicating
CHECKSUM_UNNECESSARY for an encapsulated checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set skb->csum_level instead of skb->encapsulation when indicating
CHECKSUM_UNNECESSARY for an encapsulated checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set skb->csum_level instead of skb->encapsulation when indicating
CHECKSUM_UNNECESSARY for an encapsulated checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set skb->csum_level instead of skb->encapsulation when indicating
CHECKSUM_UNNECESSARY for an encapsulated checksum.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The be2net driver was still using dev_kfree_skb_any() in a "normal"
skb freeing path. This rather clutters perf top -G -e skb_kfree_skb
profiling.
Signed-off-by: Rick Jones <rick.jones2@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a sprase warning introduced recently by commit
eeed018cbf ("bnx2x: Add timestamping and PTP hardware clock support"),
as well as another unrelated sparse endian issue.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to run Power On Self Test (POST) for 83xx adapters.
POST can be run in 3 different speed modes :
i) Fast mode (takes about 690 ms)
ii) Medium mode (takes about 2930 ms)
iii) Slow mode (takes about 7500 ms)
To run POST, firmware file with name "83xx_post_fw.bin" should be present under
/lib/firmware directory. load_fw_file module parameter is used to specify
POST operation and its speed mode.
load_fw_file = 2 : Fast mode
load_fw_file = 3 : Medium mode
load_fw_file = 4 : Slow mode
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per recommendation, msleep() may sleep longer than intended time for
values less than 20ms. So, use usleep_range() instead of msleep()
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Update the port type information
o Advertise correct link modes and autonegotiation
o Add support to change link speed
Signed-off-by: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the function which we use to set VXLAN DMFS (flow-steering) rules
from mlx4_en to mlx4_core. This refactoring will allow the mlx4_ib driver
to call the helper for the use case of user-space RAW Ethernet QPs, such
that they can serve VXLAN traffic too.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enabling DMA_API_DEBUG, warnings are reported at runtime
because the device driver frees DMA memory with wrong functions
and it does not call dma_mapping_error after mapping dma memory.
The first problem is fixed by of introducing a flag that helps us
keeping track which mapping technique was used, so that we can use
the right API for unmap.
This approach was inspired by the e1000 driver, which uses a similar
technique.
Signed-off-by: Andre Draszik <andre.draszik@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Denis Kirjanov <kda@linux-powerpc.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP reference clock, used for setting the addend in the Timestamp Addend
Register, was erroneously hard-coded (as reported in the databook just as
example).
The patch removes the macro named: STMMAC_SYSCLOCK and allows to use a
reference clock (clk_ptp_ref_i) that can be passed from the platform.
If not passed, the main driver clock will be used as default; note that
this can be fine on some platforms.
Note that, prior this patch, using the old STMMAC_SYSCLOCK on some platforms,
as side effect, the ptp clock can move faster/slower than the system clock.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix a typo on mmc rx crc error when reported by ethtool.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to w/a a problem that happens on some boxes when run at 10Mbps
Half duplex mode.
During the transmission the CSR signal is asserted for some time and the frames
aborted because of carrier sense error.
This is reported by MMC HW counter: txcarrier signal.
This actually is a false carrier so the frames are good and there is no reason
to ask for dropping them.
This patch so disables the Carrier Sense During Transmission
and this means that the MAC transmitter ignore the CRS signal
during frame transmission in Half-Duplex mode.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Vince Bridgers <vbridgers2013@gmail.com>
Acked-by: Ley Foon Tan <lftan@altera.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Leftover from 6e1d0b8988 ("r8169:add
support for RTL8168H and RTL8107E").
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2014-08-27
This series contains updates to i40e and i40evf.
Carolyn provides two patches, first changes the wording of the flow
director add/remove and asynchronous failure messages to include the
fd_id to try and add some way to track the operations on a given fd_id.
Second adds a check during handle_link_event for unqualified modules
when link is down and there is a module plugged in.
Anjali provides four patches to i40e/i40evf. First update flow director
messages so that a user can tell if a filter was added or deleted. Then
updates the ATR policy to not auto-disable ATR when we have errors in
programming. The disabling of ATR when we got programming errors was
buggy and was still adding new rules and causing continuous errors.
With this policy change, we flush instead when we see too many errors.
In addition she adds a flow director flush counter to ethtool to help
know how many times the interface had to flush and replay the flow
director filter table. Updates the driver to ignores a driver
perceived transmit hang if the number of descriptors pending is less
than 4, and instead log a stat when this situation happens. This is
because the queue progresses forward and the stack never experiences
a real hang in these situations.
Shannon provides three patches for i40e/i40evf, first enables the
l2tsel bit on receive queue contexts that are assigned to VFs so that
the VF can get the stripped VLAN tag. Then adds a max buffer size
parameter to the print helper to be sure the code knows when to stop.
Lastly, remove the complaint when removing the default MAC VLAN filter.
This was because old firmware had an incorrect MAC VLAN filter that
needed to be replaced at startup, and now newer firmware does not have
this problem. So now we only add the new filter if the removal
succeeded and no need to complain if the removal fails.
Ashish provides a change to vsi->num_queue_pairs to equal the number
that is configured by the VF. This limits the number of queues that
are enabled/disabled and fixes the mismatch case for when a VF
configures fewer queues than is allocated to it by the PF.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Mirror the changes made to ixgbe in commit 2367a17390
("ixgbe: flush when in xmit_more mode and under descriptor pressure")
Signed-off-by: David S. Miller <davem@davemloft.net>
When xmit_more mode is being used and the ring is about to
become full or the stack has stopped the ring, enforce a tail
pointer write to the hw. Otherwise, we could risk a TX hang.
Code suggested by Alexander Duyck.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sungem driver has "phy_read()" and "phy_write()" functions, which
we need to rename because the generic phy layer is about to export
generic interfaces with the same name.
Signed-off-by: David S. Miller <davem@davemloft.net>
The dmfe driver has "phy_read()" and "phy_write()" functions, which
we need to rename because the generic phy layer is about to export
generic interfaces with the same name.
Signed-off-by: David S. Miller <davem@davemloft.net>
Some platforms have special bank registers which might be used to
select the correct clock or the right mode for Media Indepent Interface
controllers. Sometimes, it is also required to activate vcc regulators
in the right order to supply the ethernet controller at the right time.
This patch is an architecture refactoring of the arc-emac device driver.
It adds a new software design which allows to add specific platform
glue layer. Each platform has now its own module which performs custom
initialization and remove for the target and then calls to the
core driver.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is an api changes for the emac_mdio.c module.
It will be required later when arc_emac_probe/arc_emac_remove
will no longer use 'struct platform_device'.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a preparation of an api changes for the emac_main.c module.
The involved functions are arc_emac_probe and arc_emac_remove.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Incorrect checking of array instead of array contents in panic_dump
flow - results of commit e261199872 ("bnx2x: Safe bnx2x_panic_dump()").
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bump versions for i40e to 1.0.4 and i40evf to 1.0.1.
Change-ID: I960c04da2c91bdf1d02f8e5011e68c34a634122d
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-By: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We are seeing situations where the driver sees a hang with less than 4
desc pending, if the driver chooses to ignore it the queue progresses
forward and the stack never experiences a real hang.
With this patch we will log a stat when this situation happens
"tx_sluggish" will increment and we can see some more details
at a higher debug level. Other than that we will ignore this
particular case of Tx hang.
Change-ID: I7d1d1666d990e2b12f4f6bed0d17d22e1b6410d5
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Older firmware has an incorrect MAC VLAN filter that needs to be replaced
at startup, and now newer firmware doesn't have this problem. With this
change we no longer complain if the remove fails, and we only add the
new filter if the remove succeeded.
Setting a new LAA worked the first time, but didn't work well in successive
operations, including returning to the HW default address. This simplifies
the code that was trying to be too smart.
Lastly, this pulls the hardware default mac address out into separate
handling code and keeps the broadcast filtering from getting munged.
Change-ID: I1f54b002def04ffef2546febb9a4044385452f85
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
There is at least one case in the Firmware API where the response to a
command changes the buffer size field in the AQ descriptor to a larger
number than what the request's buffer size started as. This is in addition
to setting an error flag and is in order to tell the requester how much
larger a buffer is required for the answer. We need to be sure not to
use that number when dumping the contents of the data buffer because it
can send us into the weeds and generate an invalid pointer exception.
This patch adds a max buffer size parameter to the print helper to be
sure the code knows when to stop.
Change-ID: Ib84f7ed72140fe9d600086d8f2002fc5d8753092
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds a check during handle_link_event for unqualified
module when link is down and there is a module plugged. If found,
print a message.
Change-ID: Ibd8666d77d3044c2a3dd4d762d3ae9ac6e18e943
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change vsi->num_queue_pairs to equal the number that are configured
by the VF. This, in turn, limits the number of queues that are
enable/disabled. This fixes the mismatched case for when a VF configures
fewer queues than is allocated to it by the PF.
Change other sections to use alloc_queue_pairs as warranted.
Change-ID: I0de1b55c9084e7be6acc818da8569f12128a82c2
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Enable the l2tsel bit on Rx queue contexts that are assigned to VFs so
that the VF can get the stripped VLAN tag.
Change-ID: I7d9bc56238a9ea9baf5e8a97e69b9e27ebb9d169
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Ashish Shah <ashish.n.shah@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This helps know how many times the interface had to flush and replay FD
filter table, which gives an indication on how often we are getting FD
table full situation.
Also check on certain pf states before proceeding to add or delete
filters since we can't add or delete filters if we are in those states.
Change-ID: I97f5bbbea7146833ea61af0e08ea794fccba1780
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Instead of disabling ATR when we get a programming error, we now
will wait it out to see if some room gets created by ATR rule deletion.
If we still have too many errors and ATR filter count did not change
much, its time to flush and replay. We no more auto-disable ATR when
we have errors in programming.
The disabling of ATR when we get programming error was buggy and
was still adding new rules and causing continuous errors. With this
policy change we flush instead when we see too many errors.
ATR is still disabled if we add a SB rule for TCP/IPv4 flow type,
more logic is added to re-enable it once all SB TCP/IPv4 rules are gone.
Change-ID: I77edcbeab9500c72a7e0bd7b5c5b113ced133a9c
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Change the message that gets printed when adding/deleting a filter to
the SB, so that user can tell if a filter was added or deleted.
Print filter add failures only in case of SB filters. For ATR the
information is not useful to the user and hence suppress it unless in
higher debug mode.
Change-ID: I78d7a7a6ecfa82a38a582b0d7b4da038355e3735
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch changes the wording of the flow director add/remove and
asynchronous failure messages to include fd_id to try and add some
way to track the operations on a given fd_id. Its not perfect, but
its better than what we had as PCTYPE can apply to several different
filter requests.
This patch also removes a redundant message when filter
addition fails due to full condition.
Change-ID: Icf58b0603d4f162d9fc542f11a74866a907049f2
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jim Young <jamesx.m.young@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
drivers/net/ethernet/marvell/mvneta.c: In function 'mvneta_skb_tx_csum':
drivers/net/ethernet/marvell/mvneta.c:1374:3: error: implicit declaration of function 'vlan_get_protocol' [-Werror=implicit-function-declaration]
__be16 l3_proto = vlan_get_protocol(skb);
^
Reporeted-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
bnx2x uses ptp functions, so it should select the provider of
those functions (PTP_1588_CLOCK). Fixes these build errors:
drivers/built-in.o: In function `__bnx2x_remove':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:13409:
undefined reference to `ptp_clock_unregister'
drivers/built-in.o: In function `bnx2x_register_phc':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:13202:
undefined reference to `ptp_clock_register'
drivers/built-in.o: In function `bnx2x_get_ts_info':
/home/jim/linux/drivers/net/ethernet/broadcom/bnx2x/bnx2x_ethtool.c:3498:
undefined reference to `ptp_clock_index'
Reported-by: Jim Davis <jim.epost@gmail.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit eeed018cbf ("bnx2x: Add timestamping and PTP hardware clock support")
has a missing conversion to LE32, which will prevent the feature from working
on big endian machines.
Signed-off-by: Michal Kalderon <Michal.Kalderon@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduces 2 new relaxations in the bnx2x driver regarding GRO:
1. Don't prevent SW GRO if HW GRO is disabled.
2. If all aggregations are disabled, when GRO configuration changes
there's no need to perform an inner-reload [since it will have no
actual effect].
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During statistics initialization of a VF we need to clean its statistics.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When STOP_ON_ERROR is set driver will not compile. Even if it did,
traffic will not pass without this patch as several fields which are
verified by FW/HW on the Tx path are not properly set.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This changes slightly the set of registers read during `ethtool -d'.
Without this change, it's possible the HW will generate a grc Attention which
will be logged into system logs as `grc timeout'.
Signed-off-by: Dmitry Kravkov <Dmitry.Kravkov@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO support for vlans. It also allows a user to
control vlan acceleration offloading. As such, it is possible to turn
off vlan acceleration and configure a vlan which will continue to send
TSO traffic.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information.
This results in corrupted frames sent on the wire.
This patch extracts the protocol value correctly by using a
vlan_get_protocol() helper and corrects corrupt TSO frames.
CC: Shahed Shaikh <shahed.shaikh@qlogic.com>
CC: Jitendra Kalsaria <jitendra.kalsaria@qlogic.com>
CC: Ron Mercer <ron.mercer@qlogic.com>
CC: linux-driver@qlogic.com
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Acked-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver doesn't appear to support vlan acceleration at
all. However, it does claim to support TSO and IP checksums
for vlan devices. Thus any configured vlan device would
end up passing down partial checksums or TSO frames.
The driver also uses the value from skb->protocol to
determine TSO and checksum offload information, but assumes
that skb->protocol holds the l3 protocol information.
As a result, vlan traffic with partial checksums or TSO
will fail those checks and TSO will not happen.
Fix this by using vlan_get_protocol() helper.
CC: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
Fix this by using vlan_get_protocol() helper.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO and hw checksums.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
Fix this by using vlan_get_protocol() helper.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver claims that it can do TSO and IP checksums on vlan
devices and also allows user to control vlan acceleration offloading.
This makes it possible to push traffic to this driver that has TSO or
partial checksums set, but also have a non-accelearted vlan
header. In this case, the driver will fail to correctly
identify such traffic and will not correctly perform
segmentation and checksum calculation.
Fix this by using vlan_get_protocol() helper instead of
assuming skb->protocol always has this information.
CC: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information. This results
in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
and checksums for non-accelerated traffic.
CC: Rasesh Mody <rmody@brocade.com>
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO and checksum support for vlans. It also
allows a user to control vlan acceleration offloading. As such,
it is possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO and checksum information.
This will results in corrupted frames sent on the wire.
This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This device claims TSO support for vlans. It also allows a
user to control vlan acceleration offloading. As such, it is
possible to turn off vlan acceleration and configure a vlan
which will continue to support TSO.
In such situation the packet passed down the the device will contain
a vlan header and skb->protocol will be set to ETH_P_8021Q.
The device assumes that skb->protocol contains network protocol
value and uses that value to set up TSO information. This results
in corrupted frames sent on the wire. Corruptions include
incorrect IP total length and invalid IP checksum.
This patch extract the protocol value correctly and corrects TSO
for non-accelerated traffic.
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Carolyn Wyborny <carolyn.wyborny@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
CC: Greg Rose <gregory.v.rose@intel.com>
CC: Alex Duyck <alexander.h.duyck@intel.com>
CC: John Ronciak <john.ronciak@intel.com>
CC: Mitch Williams <mitch.a.williams@intel.com>
CC: Linux NICS <linux.nics@intel.com>
CC: e1000-devel@lists.sourceforge.net
Signed-off-by: Vladislav Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If netdev_alloc_skb_ip_align() fails, subsequent code will
try to dereference an invalid pointer.
Continue to next descriptor on error.
While we're at it,
1. eliminate the chance of an endless loop, replace the main
loop with while(rx < budget)
2. use napi_complete() and remove the explicit napi_gro_flush()
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
DMA memory should be synchronized before data is passed
to/from controller.
Add dma_sync_single_for_cpu(.., DMA_FROM_DEVICE) to RX path
and dma_sync_single_for_device(.., DMA_TO_DEVICE) to TX path.
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
build_skb() is used to make skbs out of existing RX ring memory
which is bad because the RX ring is allocated only once, on probe.
Memory corruption occur because said memory is reclaimed, i.e.
__kfree_skb() (and eventually put_page()).
Replace build_skb() with netdev_alloc_skb_ip_align() and use memcpy().
Remove SKB_DATA_ALIGN() from RX buffer size while we're at it.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=69041
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TX buffer length is not cleared on ndo_start_xmit().
Failing to do so can bug/hang the controller and
cause TX interrupts to stop altogether.
Remove the readl() and compute a new value for DESC1.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=69031
Signed-off-by: Jonas Jensen <jonas.jensen@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implements the deferred tail pointer flush API for the ixgbe
driver. Similar version also proposed longer time ago by Alexander Duyck.
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Jesper Dangaard Brouer, for high packet rates the
overhead of having another indirect call in the TX path is
non-trivial.
There is the indirect call itself, and then there is all of the
reloading of the state to refetch the tail pointer value and
then write the device register.
Move to a more passive scheme, which requires very light modifications
to the device drivers.
The signal is a new skb->xmit_more value, if it is non-zero it means
that more SKBs are pending to be transmitted on the same queue as the
current SKB. And therefore, the driver may elide the tail pointer
update.
Right now skb->xmit_more is always zero.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use is_kdump_kernel() to detect kdump kernel, instead of
reset_devices.
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to properly put to NULL the ptp_clock while un-register the PTP support.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to fix the IPC bit into the GMAC control register
that must be done after the core initialization otherwise it will
not have any effect.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds simple cleanups for stmmac, removing test we know is always
true, fixing whitespace, and moving code out of if().
Signed-off-by: Pavel Machek <pavel@denx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This cuts down the number of debug information spit out by
the driver.
Signed-off-by: Dariusz Marcinkiewicz <reksio@newterm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds fix_mac_speed() support for
Altera socfpga Ethernet controller. Emac splitter is a
soft IP core in FPGA system that converts GMII interface from
Synopsys mac to RGMII/SGMII interface. This splitter core is
an optional IP if user would like to use RGMII/SGMII
interface in their system. Software needs to update a register
in splitter core when there is speed change.
Signed-off-by: Ley Foon Tan <lftan@altera.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RTL8168H is Realtek PCIe Gigabit Ethernet controller.
RTL8107E is Realtek PCIe Fast Ethernet controller.
This patch add support for these two chips.
Signed-off-by: Chun-Hao Lin <hau@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
