TC ingress policer rules depends on interface receive queue
contexts since the bandwidth profiles are attached to RQ
contexts. When an interface is brought down all the queue
contexts are freed. This in turn frees bandwidth profiles in
hardware causing ingress police rules non-functional after
the interface is brought up. Fix this by applying all the ingress
police rules config to hardware in otx2_open. Also allow
adding ingress rules only when interface is running
since no contexts exist for the interface when it is down.
Fixes: 68fbff68db ("octeontx2-pf: Add police action for TC flower")
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930217-5707-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
When more than 64 VFs are enabled for a PF then mbox communication
between VF and PF is not working as mbox work queueing for few VFs
are skipped due to wrong calculation of VF numbers.
Fixes: d424b6c024 ("octeontx2-pf: Enable SRIOV and added VF mbox handling")
Signed-off-by: Geetha sowjanya <gakula@marvell.com>
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/1700930042-5400-1-git-send-email-sbhatta@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit aeb18dd076 ("net: stmmac: xgmac: Disable MMC interrupts
by default") tries to disable MMC interrupts to avoid a storm of
unhandled interrupts, but leaves the FPE(Frame Preemption) MMC
interrupts enabled, FPE MMC interrupts can cause the same problem.
Now we mask FPE TX and RX interrupts to disable all MMC interrupts.
Fixes: aeb18dd076 ("net: stmmac: xgmac: Disable MMC interrupts by default")
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
Signed-off-by: Furong Xu <0x1207@gmail.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Link: https://lore.kernel.org/r/20231125060126.2328690-1-0x1207@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
A loop in rvu_mbox_handler_nix_bandprof_free() contains
a break if (idx == MAX_BANDPROF_PER_PFFUNC),
but if idx may reach MAX_BANDPROF_PER_PFFUNC
buffer '(*req->prof_idx)[layer]' overflow happens before that check.
The patch moves the break to the
beginning of the loop.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: e8e095b3b3 ("octeontx2-af: cn10k: Bandwidth profiles config support").
Signed-off-by: Elena Salomatkina <elena.salomatkina.cmc@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Subbaraya Sundeep <sbhatta@marvell.com>
Link: https://lore.kernel.org/r/20231124210802.109763-1-elena.salomatkina.cmc@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Willem de Bruijn says:
====================
selftests/net: fix a few small compiler warnings
Observed a clang warning when backporting cmsg_sender.
Ran the same build against all the .c files under selftests/net.
This is clang-14 with -Wall
Which is what tools/testing/selftests/net/Makefile also enables.
====================
Link: https://lore.kernel.org/r/20231124171645.1011043-1-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Same init_rng() in both tests. The function reads /dev/urandom to
initialize srand(). In case of failure, it falls back onto the
entropy in the uninitialized variable. Not sure if this is on purpose.
But failure reading urandom should be rare, so just fail hard. While
at it, convert to getrandom(). Which man 4 random suggests is simpler
and more robust.
mptcp_inq.c:525:6:
mptcp_connect.c:1131:6:
error: variable 'foo' is used uninitialized
whenever 'if' condition is false
[-Werror,-Wsometimes-uninitialized]
Fixes: 048d19d444 ("mptcp: add basic kselftest for mptcp")
Fixes: b51880568f ("selftests: mptcp: add inq test case")
Cc: Florian Westphal <fw@strlen.de>
Signed-off-by: Willem de Bruijn <willemb@google.com>
----
When input is randomized because this is expected to meaningfully
explore edge cases, should we also add
1. logging the random seed to stdout and
2. adding a command line argument to replay from a specific seed
I can do this in net-next, if authors find it useful in this case.
Reviewed-by: Matthieu Baerts <matttbe@kernel.org>
Link: https://lore.kernel.org/r/20231124171645.1011043-5-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signedness of char is signed on x86_64, but unsigned on arm64.
Fix the warning building cmsg_sender.c on signed platforms or
forced with -fsigned-char:
msg_sender.c:455:12:
error: implicit conversion from 'int' to 'char'
changes value from 128 to -128
[-Werror,-Wconstant-conversion]
buf[0] = ICMPV6_ECHO_REQUEST;
constant ICMPV6_ECHO_REQUEST is 128.
Link: https://lwn.net/Articles/911914
Fixes: de17e305a8 ("selftests: net: cmsg_sender: support icmp and raw sockets")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Link: https://lore.kernel.org/r/20231124171645.1011043-3-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Fix a small compiler warning.
nr_process must be a signed long: it is assigned a signed long by
strtol() and is compared against LONG_MIN and LONG_MAX.
ipsec.c:2280:65:
error: result of comparison of constant -9223372036854775808
with expression of type 'unsigned int' is always false
[-Werror,-Wtautological-constant-out-of-range-compare]
if ((errno == ERANGE && (nr_process == LONG_MAX || nr_process == LONG_MIN))
Fixes: bc2652b7ae ("selftest/net/xfrm: Add test for ipsec tunnel")
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Dmitry Safonov <0x7f454c46@gmail.com>
Link: https://lore.kernel.org/r/20231124171645.1011043-2-willemdebruijn.kernel@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ioana Ciornei says:
====================
dpaa2-eth: various fixes
The first patch fixes a memory corruption issue happening between the Tx
and Tx confirmation of a packet by making the Tx alignment at 64bytes
mandatory instead of optional as it was previously.
The second patch fixes the Rx copybreak code path which recycled the
initial data buffer before all processing was done on the packet.
Changes in v2:
- squashed patches #1 and #2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The blamed commit added support for Rx copybreak. This meant that for
certain frame sizes, a new skb was allocated and the initial data buffer
was recycled. Instead of waiting to recycle the Rx buffer only after all
processing was done on it (like accessing the parse results or timestamp
information), the code path just went ahead and re-used the buffer right
away.
This sometimes lead to corrupted HW and SW annotation areas.
Fix this by delaying the moment when the buffer is recycled.
Fixes: 50f826999a ("dpaa2-eth: add rx copybreak support")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increase the needed headroom to account for a 64 byte alignment
restriction which, with this patch, we make mandatory on the Tx path.
The case in which the amount of headroom needed is not available is
already handled by the driver which instead sends a S/G frame with the
first buffer only holding the SW and HW annotation areas.
Without this patch, we can empirically see data corruption happening
between Tx and Tx confirmation which sometimes leads to the SW
annotation area being overwritten.
Since this is an old IP where the hardware team cannot help to
understand the underlying behavior, we make the Tx alignment mandatory
for all frames to avoid the crash on Tx conf. Also, remove the comment
that suggested that this is just an optimization.
This patch also sets the needed_headroom net device field to the usual
value that the driver would need on the Tx path:
- 64 bytes for the software annotation area
- 64 bytes to account for a 64 byte aligned buffer address
Fixes: 6e2387e8f1 ("staging: fsl-dpaa2/eth: Add Freescale DPAA2 Ethernet driver")
Closes: https://lore.kernel.org/netdev/aa784d0c-85eb-4e5d-968b-c8f74fa86be6@gin.de/
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit b92143d442 ("net: dsa: mv88e6xxx: add infrastructure for
phylink_pcs") probing of a Marvell 88e6350 switch causes a NULL pointer
de-reference like this example:
...
mv88e6085 d0072004.mdio-mii:11: switch 0x3710 detected: Marvell 88E6350, revision 2
8<--- cut here ---
Unable to handle kernel NULL pointer dereference at virtual address 00000000 when read
[00000000] *pgd=00000000
Internal error: Oops: 5 [#1] ARM
Modules linked in:
CPU: 0 PID: 8 Comm: kworker/u2:0 Not tainted 6.7.0-rc2-dirty #26
Hardware name: Marvell Armada 370/XP (Device Tree)
Workqueue: events_unbound deferred_probe_work_func
PC is at mv88e6xxx_port_setup+0x1c/0x44
LR is at dsa_port_devlink_setup+0x74/0x154
pc : [<c057ea24>] lr : [<c0819598>] psr: a0000013
sp : c184fce0 ip : c542b8f4 fp : 00000000
r10: 00000001 r9 : c542a540 r8 : c542bc00
r7 : c542b838 r6 : c5244580 r5 : 00000005 r4 : c5244580
r3 : 00000000 r2 : c542b840 r1 : 00000005 r0 : c1a02040
...
The Marvell 6350 switch has no SERDES interface and so has no
corresponding pcs_ops defined for it. But during probing a call is made
to mv88e6xxx_port_setup() which unconditionally expects pcs_ops to exist -
though the presence of the pcs_ops->pcs_init function is optional.
Modify code to check for pcs_ops first, before checking for and calling
pcs_ops->pcs_init. Modify checking and use of pcs_ops->pcs_teardown
which may potentially suffer the same problem.
Fixes: b92143d442 ("net: dsa: mv88e6xxx: add infrastructure for phylink_pcs")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
As of commit de5c9bf40c ("net: phylink: require supported_interfaces to
be filled") Marvell 88e6350 switches fail to be probed:
...
mv88e6085 d0072004.mdio-mii:11: switch 0x3710 detected: Marvell 88E6350, revision 2
mv88e6085 d0072004.mdio-mii:11: phylink: error: empty supported_interfaces
error creating PHYLINK: -22
mv88e6085: probe of d0072004.mdio-mii:11 failed with error -22
...
The problem stems from the use of mv88e6185_phylink_get_caps() to get
the device capabilities. Create a new dedicated phylink_get_caps for the
6351 family (which the 6350 is one of) to properly support their set of
capabilities.
According to chip.h the 6351 switch family includes the 6171, 6175, 6350
and 6351 switches, so update each of these to use the correct
phylink_get_caps.
Fixes: de5c9bf40c ("net: phylink: require supported_interfaces to be filled")
Signed-off-by: Greg Ungerer <gerg@kernel.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added initialization use_ack to mptcp_parse_option().
Reported-by: syzbot+b834a6b2decad004cfa1@syzkaller.appspotmail.com
Signed-off-by: Edward Adam Davis <eadavis@qq.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before returning the rswitch_start_xmit() in the error path,
dev_kfree_skb_any() should be called. So, fix it.
Fixes: 33f5d733b5 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This .ndo_start_xmit() function should return netdev_tx_t value,
not -ENOMEM. So, fix it.
Fixes: 33f5d733b5 ("net: renesas: rswitch: Improve TX timestamp accuracy")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The type of ret in rswitch_start_xmit() should be netdev_tx_t. So,
fix it.
Fixes: 3590918b5d ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current release - regressions:
- Revert "net: r8169: Disable multicast filter for RTL8168H
and RTL8107E"
- kselftest: rtnetlink: fix ip route command typo
Current release - new code bugs:
- s390/ism: make sure ism driver implies smc protocol in kconfig
- two build fixes for tools/net
Previous releases - regressions:
- rxrpc: couple of ACK/PING/RTT handling fixes
Previous releases - always broken:
- bpf: verify bpf_loop() callbacks as if they are called unknown
number of times
- improve stability of auto-bonding with Hyper-V
- account BPF-neigh-redirected traffic in interface statistics
Misc:
- net: fill in some more MODULE_DESCRIPTION()s
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----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=2sG4
-----END PGP SIGNATURE-----
Merge tag 'net-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net
Pull networking fixes from Jakub Kicinski:
"Including fixes from bpf.
Current release - regressions:
- Revert "net: r8169: Disable multicast filter for RTL8168H and
RTL8107E"
- kselftest: rtnetlink: fix ip route command typo
Current release - new code bugs:
- s390/ism: make sure ism driver implies smc protocol in kconfig
- two build fixes for tools/net
Previous releases - regressions:
- rxrpc: couple of ACK/PING/RTT handling fixes
Previous releases - always broken:
- bpf: verify bpf_loop() callbacks as if they are called unknown
number of times
- improve stability of auto-bonding with Hyper-V
- account BPF-neigh-redirected traffic in interface statistics
Misc:
- net: fill in some more MODULE_DESCRIPTION()s"
* tag 'net-6.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (58 commits)
tools: ynl: fix duplicate op name in devlink
tools: ynl: fix header path for nfsd
net: ipa: fix one GSI register field width
tls: fix NULL deref on tls_sw_splice_eof() with empty record
net: axienet: Fix check for partial TX checksum
vsock/test: fix SEQPACKET message bounds test
i40e: Fix adding unsupported cloud filters
ice: restore timestamp configuration after device reset
ice: unify logic for programming PFINT_TSYN_MSK
ice: remove ptp_tx ring parameter flag
amd-xgbe: propagate the correct speed and duplex status
amd-xgbe: handle the corner-case during tx completion
amd-xgbe: handle corner-case during sfp hotplug
net: veth: fix ethtool stats reporting
octeontx2-pf: Fix ntuple rule creation to direct packet to VF with higher Rx queue than its PF
net: usb: qmi_wwan: claim interface 4 for ZTE MF290
Revert "net: r8169: Disable multicast filter for RTL8168H and RTL8107E"
net/smc: avoid data corruption caused by decline
nfc: virtual_ncidev: Add variable to check if ndev is running
dpll: Fix potential msg memleak when genlmsg_put_reply failed
...
We don't support CRUD-inspired message types in YNL too well.
One aspect that currently trips us up is the fact that single
message ID can be used in multiple commands (as the response).
This leads to duplicate entries in the id-to-string tables:
devlink-user.c:19:34: warning: initialized field overwritten [-Woverride-init]
19 | [DEVLINK_CMD_PORT_NEW] = "port-new",
| ^~~~~~~~~~
devlink-user.c:19:34: note: (near initialization for ‘devlink_op_strmap[7]’)
Fixes tag points at where the code was generated, the "real" problem
is that the code generator does not support CRUD.
Fixes: f2f9dd164d ("netlink: specs: devlink: add the remaining command to generate complete split_ops")
Link: https://lore.kernel.org/r/20231123030558.1611831-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The makefile dependency is trying to include the wrong header:
<command-line>: fatal error: ../../../../include/uapi//linux/nfsd.h: No such file or directory
The guard also looks wrong.
Fixes: f14122b2c2 ("tools: ynl: Add source files for nfsd netlink protocol")
Reviewed-by: Chuck Lever <chuck.lever@oracle.com>
Link: https://lore.kernel.org/r/20231123030624.1611925-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The width of the R_LENGTH field of the EV_CH_E_CNTXT_1 GSI register
is 24 bits (not 20 bits) starting with IPA v5.0. Fix this.
Fixes: faf0678ec8 ("net: ipa: add IPA v5.0 GSI register definitions")
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20231122231708.896632-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzkaller discovered that if tls_sw_splice_eof() is executed as part of
sendfile() when the plaintext/ciphertext sk_msg are empty, the send path
gets confused because the empty ciphertext buffer does not have enough
space for the encryption overhead. This causes tls_push_record() to go on
the `split = true` path (which is only supposed to be used when interacting
with an attached BPF program), and then get further confused and hit the
tls_merge_open_record() path, which then assumes that there must be at
least one populated buffer element, leading to a NULL deref.
It is possible to have empty plaintext/ciphertext buffers if we previously
bailed from tls_sw_sendmsg_locked() via the tls_trim_both_msgs() path.
tls_sw_push_pending_record() already handles this case correctly; let's do
the same check in tls_sw_splice_eof().
Fixes: df720d288d ("tls/sw: Use splice_eof() to flush")
Cc: stable@vger.kernel.org
Reported-by: syzbot+40d43509a099ea756317@syzkaller.appspotmail.com
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20231122214447.675768-1-jannh@google.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Due to a typo, the code checked the RX checksum feature in the TX path.
Fixes: 8a3b7a252d ("drivers/net/ethernet/xilinx: added Xilinx AXI Ethernet driver")
Signed-off-by: Samuel Holland <samuel.holland@sifive.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Link: https://lore.kernel.org/r/20231122004219.3504219-1-samuel.holland@sifive.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tune message length calculation to make this test work on machines
where 'getpagesize()' returns >32KB. Now maximum message length is not
hardcoded (on machines above it was smaller than 'getpagesize()' return
value, thus we get negative value and test fails), but calculated at
runtime and always bigger than 'getpagesize()' result. Reproduced on
aarch64 with 64KB page size.
Fixes: 5c338112e4 ("test/vsock: rework message bounds test")
Signed-off-by: Arseniy Krasnov <avkrasnov@salutedevices.com>
Reported-by: Bogdan Marcynkov <bmarcynk@redhat.com>
Reviewed-by: Stefano Garzarella <sgarzare@redhat.com>
Link: https://lore.kernel.org/r/20231121211642.163474-1-avkrasnov@salutedevices.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
If a VF tries to add unsupported cloud filter through virtchnl
then i40e_add_del_cloud_filter(_big_buf) returns -ENOTSUPP but
this error code is stored in 'ret' instead of 'aq_ret' that
is used as error code sent back to VF. In this scenario where
one of the mentioned functions fails the value of 'aq_ret'
is zero so the VF will incorrectly receive a 'success'.
Use 'aq_ret' to store return value and remove 'ret' local
variable. Additionally fix the issue when filter allocation
fails, in this case no notification is sent back to the VF.
Fixes: e284fc2804 ("i40e: Add and delete cloud filter")
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Tested-by: Rafal Romanowski <rafal.romanowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20231121211338.3348677-1-anthony.l.nguyen@intel.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Tony Nguyen says:
====================
ice: restore timestamp config after reset
Jake Keller says:
We recently discovered during internal validation that the ice driver has
not been properly restoring Tx timestamp configuration after a device reset,
which resulted in application failures after a device reset.
After some digging, it turned out this problem is two-fold. Since the
introduction of the PTP support the driver has been clobbering the storage
of the current timestamp configuration during reset. Thus after a reset, the
driver will no longer perform Tx or Rx timestamps, and will report
timestamp configuration as disabled if SIOCGHWTSTAMP ioctl is issued.
In addition, the recently merged auxiliary bus support code missed that
PFINT_TSYN_MSK must be reprogrammed on the clock owner for E822 devices.
Failure to restore this register configuration results in the driver no
longer responding to interrupts from other ports. Depending on the traffic
pattern, this can either result in increased latency responding to
timestamps on the non-owner ports, or it can result in the driver never
reporting any timestamps. The configuration of PFINT_TSYN_MSK was only done
during initialization. Due to this, the Tx timestamp issue persists even if
userspace reconfigures timestamping.
This series fixes both issues, as well as removes a redundant Tx ring field
since we can rely on the skb flag as the primary detector for a Tx timestamp
request.
Note that I don't think this series will directly apply to older stable
releases (even v6.6) as we recently refactored a lot of the PTP code to
support auxiliary bus. Patch 2/3 only matters for the post-auxiliary bus
implementation. The principle of patch 1/3 and 3/3 could apply as far back
as the initial PTP support, but I don't think it will apply cleanly as-is.
====================
Link: https://lore.kernel.org/r/20231121211259.3348630-1-anthony.l.nguyen@intel.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The driver calls ice_ptp_cfg_timestamp() during ice_ptp_prepare_for_reset()
to disable timestamping while the device is resetting. This operation
destroys the user requested configuration. While the driver does call
ice_ptp_cfg_timestamp in ice_rebuild() to restore some hardware settings
after a reset, it unconditionally passes true or false, resulting in
failure to restore previous user space configuration.
This results in a device reset forcibly disabling timestamp configuration
regardless of current user settings.
This was not detected previously due to a quirk of the LinuxPTP ptp4l
application. If ptp4l detects a missing timestamp, it enters a fault state
and performs recovery logic which includes executing SIOCSHWTSTAMP again,
restoring the now accidentally cleared configuration.
Not every application does this, and for these applications, timestamps
will mysteriously stop after a PF reset, without being restored until an
application restart.
Fix this by replacing ice_ptp_cfg_timestamp() with two new functions:
1) ice_ptp_disable_timestamp_mode() which unconditionally disables the
timestamping logic in ice_ptp_prepare_for_reset() and ice_ptp_release()
2) ice_ptp_restore_timestamp_mode() which calls
ice_ptp_restore_tx_interrupt() to restore Tx timestamping configuration,
calls ice_set_rx_tstamp() to restore Rx timestamping configuration, and
issues an immediate TSYN_TX interrupt to ensure that timestamps which
may have occurred during the device reset get processed.
Modify the ice_ptp_set_timestamp_mode to directly save the user
configuration and then call ice_ptp_restore_timestamp_mode. This way, reset
no longer destroys the saved user configuration.
This obsoletes the ice_set_tx_tstamp() function which can now be safely
removed.
With this change, all devices should now restore Tx and Rx timestamping
functionality correctly after a PF reset without application intervention.
Fixes: 77a781155a ("ice: enable receive hardware timestamping")
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Commit d938a8cca8 ("ice: Auxbus devices & driver for E822 TS") modified
how Tx timestamps are handled for E822 devices. On these devices, only the
clock owner handles reading the Tx timestamp data from firmware. To do
this, the PFINT_TSYN_MSK register is modified from the default value to one
which enables reacting to a Tx timestamp on all PHY ports.
The driver currently programs PFINT_TSYN_MSK in different places depending
on whether the port is the clock owner or not. For the clock owner, the
PFINT_TSYN_MSK value is programmed during ice_ptp_init_owner just before
calling ice_ptp_tx_ena_intr to program the PHY ports.
For the non-clock owner ports, the PFINT_TSYN_MSK is programmed during
ice_ptp_init_port.
If a large enough device reset occurs, the PFINT_TSYN_MSK register will be
reset to the default value in which only the PHY associated directly with
the PF will cause the Tx timestamp interrupt to trigger.
The driver lacks logic to reprogram the PFINT_TSYN_MSK register after a
device reset. For the E822 device, this results in the PF no longer
responding to interrupts for other ports. This results in failure to
deliver Tx timestamps to user space applications.
Rename ice_ptp_configure_tx_tstamp to ice_ptp_cfg_tx_interrupt, and unify
the logic for programming PFINT_TSYN_MSK and PFINT_OICR_ENA into one place.
This function will program both registers according to the combination of
user configuration and device requirements.
This ensures that PFINT_TSYN_MSK is always restored when we configure the
Tx timestamp interrupt.
Fixes: d938a8cca8 ("ice: Auxbus devices & driver for E822 TS")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Before performing a Tx timestamp in ice_stamp(), the driver checks a ptp_tx
ring variable to see if timestamping is enabled on that ring. This value is
set for all rings whenever userspace configures Tx timestamping.
Ostensibly this was done to avoid wasting cycles checking other fields when
timestamping has not been enabled. However, for Tx timestamps we already
get an individual per-SKB flag indicating whether userspace wants to
request a timestamp on that packet. We do not gain much by also having
a separate flag to check for whether timestamping was enabled.
In fact, the driver currently fails to restore the field after a PF reset.
Because of this, if a PF reset occurs, timestamps will be disabled.
Since this flag doesn't add value in the hotpath, remove it and always
provide a timestamp if the SKB flag has been set.
A following change will fix the reset path to properly restore user
timestamping configuration completely.
This went unnoticed for some time because one of the most common
applications using Tx timestamps, ptp4l, will reconfigure the socket as
part of its fault recovery logic.
Fixes: ea9b847cda ("ice: enable transmit timestamps for E810 devices")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Tested-by: Pucha Himasekhar Reddy <himasekharx.reddy.pucha@intel.com> (A Contingent worker at Intel)
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
xgbe_get_link_ksettings() does not propagate correct speed and duplex
information to ethtool during cable unplug. Due to which ethtool reports
incorrect values for speed and duplex.
Address this by propagating correct information.
Fixes: 7c12aa0877 ("amd-xgbe: Move the PHY support into amd-xgbe")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The existing implementation uses software logic to accumulate tx
completions until the specified time (1ms) is met and then poll them.
However, there exists a tiny gap which leads to a race between
resetting and checking the tx_activate flag. Due to this the tx
completions are not reported to upper layer and tx queue timeout
kicks-in restarting the device.
To address this, introduce a tx cleanup mechanism as part of the
periodic maintenance process.
Fixes: c5aa9e3b81 ("amd-xgbe: Initial AMD 10GbE platform driver")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Force the mode change for SFI in Fixed PHY configurations. Fixed PHY
configurations needs PLL to be enabled while doing mode set. When the
SFP module isn't connected during boot, driver assumes AN is ON and
attempts auto-negotiation. However, if the connected SFP comes up in
Fixed PHY configuration the link will not come up as PLL isn't enabled
while the initial mode set command is issued. So, force the mode change
for SFI in Fixed PHY configuration to fix link issues.
Fixes: e57f7a3fea ("amd-xgbe: Prepare for working with more than one type of phy")
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Raju Rangoju <Raju.Rangoju@amd.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Fix a possible misalignment between page_pool stats and tx xdp_stats
reported in veth_get_ethtool_stats routine.
The issue can be reproduced configuring the veth pair with the
following tx/rx queues:
$ip link add v0 numtxqueues 2 numrxqueues 4 type veth peer name v1 \
numtxqueues 1 numrxqueues 1
and loading a simple XDP program on v0 that just returns XDP_PASS.
In this case on v0 the page_pool stats overwrites tx xdp_stats for queue 1.
Fix the issue incrementing pp_idx of dev->real_num_tx_queues * VETH_TQ_STATS_LEN
since we always report xdp_stats for all tx queues in ethtool.
Fixes: 4fc418053e ("net: veth: add page_pool stats")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/r/c5b5d0485016836448453f12846c7c4ab75b094a.1700593593.git.lorenzo@kernel.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
It is possible to add a ntuple rule which would like to direct packet to
a VF whose number of queues are greater/less than its PF's queue numbers.
For example a PF can have 2 Rx queues but a VF created on that PF can have
8 Rx queues. As of today, ntuple rule will reject rule because it is
checking the requested queue number against PF's number of Rx queues.
As a part of this fix if the action of a ntuple rule is to move a packet
to a VF's queue then the check is removed. Also, a debug information is
printed to aware user that it is user's responsibility to cross check if
the requested queue number on that VF is a valid one.
Fixes: f0a1913f8a ("octeontx2-pf: Add support for ethtool ntuple filters")
Signed-off-by: Suman Ghosh <sumang@marvell.com>
Reviewed-by: Wojciech Drewek <wojciech.drewek@intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20231121165624.3664182-1-sumang@marvell.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----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=K1pI
-----END PGP SIGNATURE-----
Merge tag 'loongarch-fixes-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson
Pull LoongArch fixes from Huacai Chen:
"Fix several build errors, a potential kernel panic, a cpu hotplug
issue and update links in documentations"
* tag 'loongarch-fixes-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/chenhuacai/linux-loongson:
Docs/zh_CN/LoongArch: Update links in LoongArch introduction.rst
Docs/LoongArch: Update links in LoongArch introduction.rst
LoongArch: Implement constant timer shutdown interface
LoongArch: Mark {dmw,tlb}_virt_to_page() exports as non-GPL
LoongArch: Silence the boot warning about 'nokaslr'
LoongArch: Add __percpu annotation for __percpu_read()/__percpu_write()
LoongArch: Record pc instead of offset in la_abs relocation
LoongArch: Explicitly set -fdirect-access-external-data for vmlinux
LoongArch: Add dependency between vmlinuz.efi and vmlinux.efi
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEIbPD0id6easf0xsudhRwX5BBoF4FAmVdgqYTHHdlaS5saXVA
a2VybmVsLm9yZwAKCRB2FHBfkEGgXhBsCACzUGLF3vOQdrmgTMymzaaOzfLJtvNW
oQ34FwMJMOAyJ6FxM12IJPHA2j+azl9CPjQc5O6F2CBcF8hVj2mDIINQIi+4wpV5
FQv445g2KFml/+AJr/1waz1GmhHtr1rfu7B7NX6tPUtOpxKN7AHAQXWYmHnwK8BJ
5Mh2a/7Lphjin4M1FWCeBTj0JtqF1oVAW2L9jsjqogq1JV0a51DIFutROtaPSC/4
ssTLM5Rqpnw8Z1GWVYD2PObIW4A+h1LV1tNGOIoGW6mX56mPU+KmVA7tTKr8Je/i
z3Jk8bZXFyLvPW2+KNJacbldKNcfwAFpReffNz/FO3R16Stq9Ta1mcE2
=wXju
-----END PGP SIGNATURE-----
Merge tag 'hyperv-fixes-signed-20231121' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux
Pull hyperv fixes from Wei Liu:
- One fix for the KVP daemon (Ani Sinha)
- Fix for the detection of E820_TYPE_PRAM in a Gen2 VM (Saurabh Sengar)
- Micro-optimization for hv_nmi_unknown() (Uros Bizjak)
* tag 'hyperv-fixes-signed-20231121' of git://git.kernel.org/pub/scm/linux/kernel/git/hyperv/linux:
x86/hyperv: Use atomic_try_cmpxchg() to micro-optimize hv_nmi_unknown()
x86/hyperv: Fix the detection of E820_TYPE_PRAM in a Gen2 VM
hv/hv_kvp_daemon: Some small fixes for handling NM keyfiles
We really don't want to do atomic_read() or anything like that, since we
already have the value, not the lock. The whole point of this is that
we've loaded the lock from memory, and we want to check whether the
value we loaded was a locked one or not.
The main use of this is the lockref code, which loads both the lock and
the reference count in one atomic operation, and then works on that
combined value. With the atomic_read(), the compiler would pointlessly
spill the value to the stack, in order to then be able to read it back
"atomically".
This is the qspinlock version of commit c6f4a90022 ("asm-generic:
ticket-lock: Optimize arch_spin_value_unlocked()") which fixed this same
bug for ticket locks.
Cc: Guo Ren <guoren@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Waiman Long <longman@redhat.com>
Link: https://lore.kernel.org/all/CAHk-=whNRv0v6kQiV5QO6DJhjH4KEL36vWQ6Re8Csrnh4zbRkQ@mail.gmail.com/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This reverts commit efa5f1311c.
I couldn't reproduce the reported issue. What I did, based on a pcap
packet log provided by the reporter:
- Used same chip version (RTL8168h)
- Set MAC address to the one used on the reporters system
- Replayed the EAPOL unicast packet that, according to the reporter,
was filtered out by the mc filter.
The packet was properly received.
Therefore the root cause of the reported issue seems to be somewhere
else. Disabling mc filtering completely for the most common chip
version is a quite big hammer. Therefore revert the change and wait
for further analysis results from the reporter.
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We found a data corruption issue during testing of SMC-R on Redis
applications.
The benchmark has a low probability of reporting a strange error as
shown below.
"Error: Protocol error, got "\xe2" as reply type byte"
Finally, we found that the retrieved error data was as follows:
0xE2 0xD4 0xC3 0xD9 0x04 0x00 0x2C 0x20 0xA6 0x56 0x00 0x16 0x3E 0x0C
0xCB 0x04 0x02 0x01 0x00 0x00 0x20 0x00 0x00 0x00 0x00 0x00 0x00 0x00
0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0xE2
It is quite obvious that this is a SMC DECLINE message, which means that
the applications received SMC protocol message.
We found that this was caused by the following situations:
client server
¦ clc proposal
------------->
¦ clc accept
<-------------
¦ clc confirm
------------->
wait llc confirm
send llc confirm
¦failed llc confirm
¦ x------
(after 2s)timeout
wait llc confirm rsp
wait decline
(after 1s) timeout
(after 2s) timeout
¦ decline
-------------->
¦ decline
<--------------
As a result, a decline message was sent in the implementation, and this
message was read from TCP by the already-fallback connection.
This patch double the client timeout as 2x of the server value,
With this simple change, the Decline messages should never cross or
collide (during Confirm link timeout).
This issue requires an immediate solution, since the protocol updates
involve a more long-term solution.
Fixes: 0fb0b02bd6 ("net/smc: adapt SMC client code to use the LLC flow")
Signed-off-by: D. Wythe <alibuda@linux.alibaba.com>
Reviewed-by: Wen Gu <guwen@linux.alibaba.com>
Reviewed-by: Wenjia Zhang <wenjia@linux.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
syzbot reported an memory leak that happens when an skb is add to
send_buff after virtual nci closed.
This patch adds a variable to track if the ndev is running before
handling new skb in send function.
Signed-off-by: Nguyen Dinh Phi <phind.uet@gmail.com>
Reported-by: syzbot+6eb09d75211863f15e3e@syzkaller.appspotmail.com
Closes: https://lore.kernel.org/lkml/00000000000075472b06007df4fb@google.com
Reviewed-by: Bongsu Jeon
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should clean the skb resource if genlmsg_put_reply failed.
Fixes: 9d71b54b65 ("dpll: netlink: Add DPLL framework base functions")
Signed-off-by: Hao Ge <gehao@kylinos.cn>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://lore.kernel.org/r/20231121013709.73323-1-gehao@kylinos.cn
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTFp0I1jqZrAX+hPRXbK58LschIgwUCZVz1PAAKCRDbK58LschI
g/RHAQCid/nEX6phIBKnsxzPSsJv4/W9WsXuqw5OfN9eUW/kUAEAoC4M1trPgUZG
/nzFP3BLOZR2jqZaVwL/xu/H5fp0DwA=
=nNka
-----END PGP SIGNATURE-----
Merge tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf
Daniel Borkmann says:
====================
pull-request: bpf 2023-11-21
We've added 19 non-merge commits during the last 4 day(s) which contain
a total of 18 files changed, 1043 insertions(+), 416 deletions(-).
The main changes are:
1) Fix BPF verifier to validate callbacks as if they are called an unknown
number of times in order to fix not detecting some unsafe programs,
from Eduard Zingerman.
2) Fix bpf_redirect_peer() handling which missed proper stats accounting
for veth and netkit and also generally fix missing stats for the latter,
from Peilin Ye, Daniel Borkmann et al.
* tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf:
selftests/bpf: check if max number of bpf_loop iterations is tracked
bpf: keep track of max number of bpf_loop callback iterations
selftests/bpf: test widening for iterating callbacks
bpf: widening for callback iterators
selftests/bpf: tests for iterating callbacks
bpf: verify callbacks as if they are called unknown number of times
bpf: extract setup_func_entry() utility function
bpf: extract __check_reg_arg() utility function
selftests/bpf: fix bpf_loop_bench for new callback verification scheme
selftests/bpf: track string payload offset as scalar in strobemeta
selftests/bpf: track tcp payload offset as scalar in xdp_synproxy
selftests/bpf: Add netkit to tc_redirect selftest
selftests/bpf: De-veth-ize the tc_redirect test case
bpf, netkit: Add indirect call wrapper for fetching peer dev
bpf: Fix dev's rx stats for bpf_redirect_peer traffic
veth: Use tstats per-CPU traffic counters
netkit: Add tstats per-CPU traffic counters
net: Move {l,t,d}stats allocation to core and convert veth & vrf
net, vrf: Move dstats structure to core
====================
Link: https://lore.kernel.org/r/20231121193113.11796-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
There has been more than a few threads which went idle before
the merge window and now people came back to them and started
asking about next steps.
We currently tell people to be patient and not to repost too
often. Our "not too often", however, is still a few orders of
magnitude faster than other subsystems. Or so I feel after
hearing people talk about review rates at LPC.
Clarify in the doc that if the discussion went idle for a week
on netdev, 95% of the time there's no point waiting longer.
Link: https://lore.kernel.org/r/20231120200109.620392-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Using generic ASIX Electronics Corp. AX88179 Gigabit Ethernet device,
the following test cycle has been implemented:
- power on
- check logs
- shutdown
- after detecting the system shutdown, disconnect power
- after approximately 60 seconds of sleep, power is restored
Running some cycles, sometimes error logs like this appear:
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to write reg index 0x0001: -19
kernel: ax88179_178a 2-9:1.0 (unnamed net_device) (uninitialized): Failed to read reg index 0x0001: -19
...
These failed operation are happening during ax88179_reset execution, so
the initialization could not be correct.
In order to avoid this, we need to increase the delay after reset and
clock initial operations. By using these larger values, many cycles
have been run and no failed operations appear.
It would be better to check some status register to verify when the
operation has finished, but I do not have found any available information
(neither in the public datasheets nor in the manufacturer's driver). The
only available information for the necessary delays is the maufacturer's
driver (original values) but the proposed values are not enough for the
tested devices.
Fixes: e2ca90c276 ("ax88179_178a: ASIX AX88179_178A USB 3.0/2.0 to gigabit ethernet adapter driver")
Reported-by: Herb Wei <weihao.bj@ieisystem.com>
Tested-by: Herb Wei <weihao.bj@ieisystem.com>
Signed-off-by: Jose Ignacio Tornos Martinez <jtornosm@redhat.com>
Link: https://lore.kernel.org/r/20231120120642.54334-1-jtornosm@redhat.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
