Add r8a7779 specific support for IRLM bit configuration
in the INTC-IRQPIN driver. Without this code we need
special workaround code in arch/arm/mach-shmobile.
The IRLM bit for the INTC hardware exists on various
older SH-based SoCs and is used to select between two
modes for the external interrupt pins IRQ0 to IRQ3:
IRLM = 0: (default from reset on r8a7779)
In this mode the pins IRQ0 to IRQ3 are used together
to give a value between 0 and 15 to the SoC. External
logic is required for masking. This mode is not
supported by the INTC-IRQPIN driver.
IRLM = 1: (needs this patch or configuration elsewhere)
In this mode IRQ0 to IRQ3 operate as 4 individual
external interrupt pins. In this mode the SMSC ethernet
chip can be used via IRQ1 on r8a7779 Marzen. This mode
is the only supported mode by the INTC-IRQPIN driver.
For this patch to work the r8a7779 DTS needs to pass
the ICR0 register as the last register bank.
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Cc: Magnus Damm <magnus.damm@gmail.com>
Cc: horms@verge.net.au
Cc: jason@lakedaemon.net
Link: http://lkml.kernel.org/r/20141203121803.5936.35881.sendpatchset@w520
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This is just enough to let pm_clk_*() enable the functional clock, and
manage it for suspend/resume, if present.
Before, it was assumed enabled by the bootloader or reset state.
To prevent the clock from being disabled while the module is needed for
wake-up, implement irq_chip.irq_set_wake(), which increments/decrements
the clock's enable_count when needed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lkml.kernel.org/r/1410527720-18061-3-git-send-email-geert+renesas@glider.be
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Set the ->irq_enable() and ->irq_disable() methods to NULL to enable
lazy disable of interrupts, and set IRQCHIP_MASK_ON_SUSPEND to tell the
core that only IRQs marked as wake-ups need to stay enabled during
suspend-to-RAM.
This makes wake-up by gpio-keys from suspend-to-RAM work on
r8a7740/Armadillo.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lkml.kernel.org/r/1408546172-22484-1-git-send-email-geert+renesas@glider.be
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The SENSE register bitfield position is incorrectly computed for SoCs
that use 2-bit IRQ sense fields. Fix it.
This has been tested on the Marzen (H1) and Bockw (M1) boards.
This bug has been present since the renesas-intc-irqpin driver was
introduced by 443580486e ("irqchip: Renesas INTC External IRQ pin
driver") in v3.10-rc1.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
To disable spurious interrupts, that get triggered on certain hardware, the
irqpin driver masks them on the parent interrupt controller. To specify
such broken devices a .control_parent parameter can be provided in the
platform data. In the DT case we need a property, to do the same.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Most Renesas irqpin controllers have 4-bit sense fields, however, some
have different widths. This patch adds a DT binding to optionally
specify such non-standard values.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
On some hardware we don't have a 1-1 mapping from the external
interrupts coming from INTC to the GIC SPI pins. We can however
share lines to demux incoming IRQs on these SoCs.
This patch enables the intc_irqpin driver to detect requests for shared
interrupt lines and demuxes them properly by querying the INTC INTREQx0A
registers.
If you need multiple shared intc_irqpin device instances, be sure to mask
out all interrupts on the INTC that share the one line before you start
to register them. Else you run into IRQ floods that would be caused by
interrupts for which no handler has been set up yet when the first
intc_irqpin device is registered.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add initial DT support to the INTC External IRQ Pin
driver. At this point only hardware with 4-bit wide
sense registers is supported via DT.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use devm_kzalloc(), devm_ioremap_nocache()
and devm_request_irq() to simplify error
handling.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Add comments to describe the special case for
"force" versions of enable and disable functions.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Cache IRQ in domain_irq variable instead of
making use of irq_find_mapping(). While at it
rename the irq variable to requested_irq.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Remove whitespace damage and add newline
between variables and code.
Signed-off-by: Magnus Damm <damm@opensource.se>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
This patch adds a driver for external IRQ pins connected
to the INTC block on recent SoCs from Renesas.
The INTC hardware block usually contains a rather wide
range of features ranging from external IRQ pin handling
to legacy interrupt controller support. On older SoCs
the INTC is used as a general purpose interrupt controller
both for external IRQ pins and on-chip devices.
On more recent ARM based SoCs with Cortex-A9 the main
interrupt controller is the GIC, but IRQ trigger setup
still need to happen in the INTC hardware block.
This driver implements the glue code needed to configure
IRQ trigger and also handle mask/unmask and demux of
external IRQ pins hooked up from the INTC to the GIC.
Tested on sh73a0 and r8a7779. The hardware varies quite
a bit with SoC model, for instance register width and
bitfield widths vary wildly. The driver requires one GIC
SPI per external IRQ pin to operate. Each driver instance
will handle up to 8 external IRQ pins.
The SoCs using this driver are currently mainly used
together with regular platform devices so this driver
allows configuration via platform data to support things
like static interrupt base address. DT support will
be added incrementally in the not so distant future.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
