To match the flow of the vendor driver, move the LLT init to after the
firmware is started.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reorganizes the device initialization to init page boundaries
before starting the firmware. This matches the flow in the 8192eu
vendor driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Newer chips can auto load the LLT table, it is no longer necessary to
build it manually in the driver.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This implements the rtl8192eu power on sequence, and splits it off
from the rtl8192cu/rtl8723au power on sequence.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The rtl8192eu can handle 1024 byte block writes, unlike it's
predecessors (8192cu/8188cu).
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This identifies the chip vendors correctly and also picks the correct
firmware for rtl8192eu.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is the start of 8192eu support. For now just detect the device
and parse the efuse.
Signed-off-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add debugfs key (under CFG80211_CERTIFICATION_ONUS
configuration) to set/clear radar_debug_mode.
In this mode, the driver simply ignores radar
events (but prints them).
The fw is notified about this mode through
a special generic_cfg_feature command.
This mode is relevant only for ap mode. look for
it when initializing ap vif.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When working with AP + P2P, it's possible to get into
a state when the AP is in ROC (due to assiciating station)
while trying to ROC on the P2P interface.
Replace the WARN_ON with wl1271_error to avoid warnings
in this case.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In cfg80211 suspend handler, stop the netif queue and
wait until all the Tx queues become empty. Start the
queues in resume handler.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We met a problem of pm_suspend when repeated closing/opening the lid
on a Lenovo laptop (1/20 reproduce rate), below is the log:
[ 199.735876] PM: Entering mem sleep
[ 199.750516] e1000e: EEE TX LPI TIMER: 00000011
[ 199.856638] Trying to free nonexistent resource <000000000000d000-000000000000d0ff>
[ 201.753566] brcmfmac: brcmf_pcie_suspend: Timeout on response for entering D3 substate
[ 201.753581] pci_legacy_suspend(): brcmf_pcie_suspend+0x0/0x1f0 [brcmfmac] returns -5
[ 201.753585] dpm_run_callback(): pci_pm_suspend+0x0/0x160 returns -5
[ 201.753589] PM: Device 0000:04:00.0 failed to suspend async: error -5
Through debugging, we found when problem happens, it is not the device
fails to enter D3, but the signal D3_ACK comes too early to pass the
waitqueue_active() check.
Just like this:
brcmf_pcie_send_mb_data(devinfo, BRCMF_H2D_HOST_D3_INFORM);
// signal is triggered here
wait_event_timeout(devinfo->mbdata_resp_wait, devinfo->mbdata_completed,
BRCMF_PCIE_MBDATA_TIMEOUT);
So far I think it is safe to remove waitqueue_active check since there
is only one place to trigger this signal (sending
BRCMF_H2D_HOST_D3_INFORM). And it is not a problem calling wake_up
event earlier than calling wait_event.
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Hante Meuleman <meuleman@broadcom.com>
Cc: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Cc: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Hui Wang <hui.wang@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We accidentally return success instead of a negative error code.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* fix AES-CMAC in AP mode (Johannes)
* adapt prints to new firmware API
* rx path improvements (Sara and Gregory)
* fixes for the thermal / cooling device code (Chaya Rachel)
* fixes for GO uAPSD handling
* more code for the 9000 device family (Sara)
* infrastructure work for firmware notification (Chaya Rachel)
* improve association reliablity (Sara)
* runtime PM fixes
* fixes for ROC (HS2.0)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJW4HQ5AAoJEC0Llv5uNjIBfHIP/j68hRW4reTJdYo0Q7MG1WPa
47ir4d/+Yz7nnXj4RFY9s8Sv6irC8gsY1bFFTZCNXDTB/BeJjvszBMGVwHuUPq+w
wg8zz8uhiAb8IlmPKnEPhuiwRrdcgqy443m06k89VNjz/kKv4/iRDQ+bL3P4O9En
LrKz9md91k5svLOuLmUXMdP+6eXKip4LBVeCgIIt2lkMNW1jYDi1Af2YEXp7Ifad
u5ow9n5aAe16QKTnMUtnShlCrdflYsBHzcxza9jKXO8hqxrHXNg9TmBNL0ZguPlQ
AdqzFmEDeUzv7GDTE4Po/DrJT13sto5gn2v36XMXLDgwS26hSqoLX1amyZ7baQyh
J986recmF5JGx/y67QE6KgSfpdDPI2E4a28d0Y4ZsFHL32SgaD0qCcOiiszjjrCD
zFYDYTPZdU9Cz6nwP27wwze0FcCCB2pOvtW5oGZb0eW1hWNb0BQlSdYIjfup7P/y
wzMIg6a5k7mGEbXpUIPpVriasTBLwNe3rmU413sm9vZkR5T5r4f3FYWHtg7dc3Rt
jP2Nb78hMC0KH/+KPBuTPdgf8hrz8JBQIJaisnfEpYjqPE1auTAsNyVNlgssHtbC
XA2l78tRe9lZNjrp6oJIon+XYGuPDzVX6geT1P9qYB7PnSI8C/rL96GVjjohqeko
1nFwhlAk0WvWjr/0NHJx
=j8++
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-03-09_2' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* update GSCAN capabilities (Ayala)
* fix AES-CMAC in AP mode (Johannes)
* adapt prints to new firmware API
* rx path improvements (Sara and Gregory)
* fixes for the thermal / cooling device code (Chaya Rachel)
* fixes for GO uAPSD handling
* more code for the 9000 device family (Sara)
* infrastructure work for firmware notification (Chaya Rachel)
* improve association reliablity (Sara)
* runtime PM fixes
* fixes for ROC (HS2.0)
Gscan capabilities were updated with new capabilities supported
by the device. While at it, simplify the firmware support
conditional and move both conditions into the WARN() to make it
easier to undertand and use the unlikely() for both.
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The firmware/hardware only supports checking AES-CMAC on RX, not
using it on TX. For station mode this is fine, since it's the only
thing it will ever do. For AP mode, it never receives such frames,
but must be able to transmit them. This is currently broken since
we try to enable them for hardware crypto (for RX only) and then
treat them as TX_CMD_SEC_EXT, leading to FIFO underruns during TX
so the frames never go out to the air.
To fix this, simply use software on TX in AP (and IBSS) mode.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Newer firmware versions put different data in the memory
which is read by the driver upon firmware crash. Just
change the variable names in the code and the name of the
data in the log that we print withouth any functional
change.
On older firmware, there will be a mismatch between the
names that are printed and the content itself, but that's
harmless.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When trying to reach high Rx throughput of more than 500Mbps on
a device with a relatively weak CPU (Atom x5-Z8500), CPU utilization
may become a bottleneck. Analysis showed that we are looping in
iwl_pcie_rx_handle for very long periods which led to starvation
of other threads (iwl_pcie_rx_handle runs with _bh disabled).
We were handling Rx and allocating new buffers and the new buffers
were ready quickly enough to be available before we had finished
handling all the buffers available in the hardware. As a
consequence, we called iwl_pcie_rxq_restock to refill the hardware
with the new buffers, and start again handling new buffers without
exiting the function. Since we read the hardware pointer again when
we goto restart, new buffers were handled immediately instead of
exiting the function.
This patch avoids refilling RBs inside rx handling loop, unless an
emergency situation is reached. It also doesn't read the hardware
pointer again unless we are in an emergency (unlikely) case.
This significantly reduce the maximal time we spend in
iwl_pcie_rx_handle with _bh disabled.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
iwl_mvm_tcool_get_cur_state is the function that returns the
cooling state index to the sysfs handler. This function returns
mvm->cooling_dev.cur_state but that variable was set to the
budget and not the cooling state index. Fix that.
Add a missing blank line while at it.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We need to track the next packet that we will reclaim in
order to know when the Tx queues are empty. This is useful
when we open or tear down an A-MPDU session which requires
to switch queue.
The next packet being reclaimed is identified by its WiFi
sequence number and this is relevant only when we use QoS.
QoS NDPs do have a TID but have a meaningless sequence
number. The spec mandates the receiver to ignore the
sequence number in this case, allowing the transmitter to
put any sequence number. Our implementation leaves it 0.
When we reclaim a QoS NDP, we can't update the next_relcaim
counter since the sequence number of the QoS NDP itself is
invalid.
We used to update the next_reclaim based on the sequence
number of the QoS NDP which reset it to 1 (0 + 1) and
because of this, we never knew when the queue got empty.
This had to sad consequence to stuck the A-MPDU state
machine in a transient state.
To fix this, don't update next_reclaim when we reclaim
a QoS NDP.
Alesya saw this bug when testing u-APSD. Because the
A-MPDU state machine was stuck in EMPTYING_DELBA, we
updated mac80211 that we still have frames for that
station when it got back to sleep. mac80211 then wrongly
set the TIM bit in the beacon and requested to release
non-existent frames from the A-MPDU queue. This led to
a situation where the client was trying to poll frames
but we had no frames to send.
Reported-by: Alesya Shapira <alesya.shapira@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
From 9000 family on, we need to get HW address from host
CSR registers.
OEM can override it by fusing the override registers - read
those first, and if those are 0 - read the OTP registers instead.
In addition - bail out if no valid mac address is present. Make
it shared for all NICs.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
We kick the allocator when we have 2 RBDs that don't have
attached RBs, and the allocator allocates 8 RBs meaning
that it needs another 6 RBDs to attach the RBs to.
The design is that allocator should always have enough RBDs
to fulfill requests, so we give in advance 6 RBDs to the
allocator so that when it is kicked, it gets additional 2 RBDs
and has enough RBDs.
These RBDs were taken from the Rx queue itself, meaning
that each Rx queue didn't have the maximal number of
RBDs, but MAX - 6.
Change initial number of RBDs in the system to include both
queue size and allocator reserves.
Note the multi-queue is always 511 instead of 512 to avoid a
full queue since we cannot detect this state easily enough in
the 9000 arch.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
When running async rx handler the framework holds the mvm->mutex
before starting the async handler, that might cause a deadlock in case
the handler calls to ops that lock the mutex as well.
Add support for running async rx handler without hold the mutex before
activating the handler.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Currently when the FW sends start/stop aux roc time event
notification with an error status, the driver returns an
error value, but does not remove the time event, and does
not notify the stack above that the time event is over.
This causes problems that the stack above assumes we are still
in the middle of a time event, and therefore can block different
events, such as scanning.
On FW failure notification, cleanup the time event parameters and
notify the stack above that the time event is over.
Signed-off-by: Matti Gottlieb <matti.gottlieb@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Our hardware de-aggregates AMSDUs but copies the mac header
as it to the de-aggregated MPDUs. We need to turn off the AMSDU
bit in the QoS control ourselves.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Add debugfs entries to get the ctdp budget average
and to stop ctdp.
Signed-off-by: Chaya Rachel Ivgi <chaya.rachel.ivgi@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
The cw1200 uses #ifdef to check for CONFIG_PM, but then
uses SIMPLE_DEV_PM_OPS, which leaves the references out when
CONFIG_PM_SLEEP is not defined, so we get a warning with
PM=y && PM_SLEEP=n:
drivers/net/wireless/st/cw1200/cw1200_spi.c:450:12: error: 'cw1200_spi_suspend' defined but not used [-Werror=unused-function]
This removes the incorrect #ifdef and instead uses a __maybe_unused
annotation to let the compiler know it can silently drop
the function definition.
For the DEV_PM_OPS definition, we can use an IS_ENABLED() check
to avoid defining the structure when CONFIG_PM is not set without
the #ifdef.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Smatch reports the following warning:
CHECK drivers/net/wireless/realtek/rtlwifi/rc.c
drivers/net/wireless/realtek/rtlwifi/rc.c:144 _rtl_rc_rate_set_series() warn: impossible condition '(wireless_mode == 256) => (0-255 == 256)'
This warning arises because commit acc6907b87a9 ("rtlwifi: Fix warning
from ieee80211_get_tx_rates() when using 5G") now checks the wireless
mode for WIRELESS_MODE_AC_ONLY (BIT(8)) in _rtl_rc_rate_set_series().
As a result, all quantities used to store the wireless mode must be u16.
This patch also reorders struct rtl_sta_info to save a little space.
Fixes: d76d65fd26 ("rtlwifi: fix broken VHT support")
Reported-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* fixes for 9000 devices data path (Sara Sharon)
* improvements in scheduled scan w/o profiles (Luca)
* new firmware support (-21.ucode)
* add MSIX support for 9000 devices (Haim Dreyfuss)
* cleanup in PCIe initialization
* enable MU-MIMO and take care of firmware restart(Sara Sharon)
===> This needs mac80211-next
* add support for large SKBs in mvm to reach A-MSDU
===> This needs mac80211-next
* add support for filtering frames from a BA session (Sara Sharon)
===> This needs mac80211-next
* start implementing the new Rx path for 9000 devices (Sara Sharon)
* enable the new RRM feature flag (Beni Lev)
* fix U-APSD enablement on P2P Client (Avri Altman)
* fix beacon abort enablement (Avri Altman)
* forbid beacon storing with WoWLAN (Matti Gottlieb)
* support unified uSniffer / regular firmware image (Golan Ben-Ami)
* fix a race between debugfs hooks and iface up (Chaya Rachel Ivgi)
* fixes for runtime PM (Luca)
* add a new module paramater to disable VHT (Andrei Otcheretianski)
* build infrastructure for Dynamic Queue Allocation (Liad Kaufman)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=b5Ae
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2016-03-02' of https://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
* add support for thermal device / cooling device (Chaya Rachel)
* fixes for 9000 devices data path (Sara Sharon)
* improvements in scheduled scan w/o profiles (Luca)
* new firmware support (-21.ucode)
* add MSIX support for 9000 devices (Haim Dreyfuss)
* cleanup in PCIe initialization
* enable MU-MIMO and take care of firmware restart(Sara Sharon)
===> This needs mac80211-next
* add support for large SKBs in mvm to reach A-MSDU
===> This needs mac80211-next
* add support for filtering frames from a BA session (Sara Sharon)
===> This needs mac80211-next
* start implementing the new Rx path for 9000 devices (Sara Sharon)
* enable the new RRM feature flag (Beni Lev)
* fix U-APSD enablement on P2P Client (Avri Altman)
* fix beacon abort enablement (Avri Altman)
* forbid beacon storing with WoWLAN (Matti Gottlieb)
* support unified uSniffer / regular firmware image (Golan Ben-Ami)
* fix a race between debugfs hooks and iface up (Chaya Rachel Ivgi)
* fixes for runtime PM (Luca)
* add a new module paramater to disable VHT (Andrei Otcheretianski)
* build infrastructure for Dynamic Queue Allocation (Liad Kaufman)
Flashes are attached and accessible through ChipCommon core, they aren't
connected to MIPS one. Moreover some new ARM devices (e.g. BCM47189) may
have serial flash accessibility using ChipCommon registers as well. To
support them we can't keep this code in MIPS core driver.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This follows the way of handling other flashes and cleans code a bit. As
next task we will want to move flash code to ChipCommon driver as:
1) Flash controllers are accesible using ChipCommon registers
2) This code isn't MIPS specific
This change prepares bcma for that.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Most of info stored in this struct wasn't really used anywhere as we put
all that data in platform data & resource as well.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the allocation of ivp fails the error handling attempts to
free an uninitialized dma_buf; this data structure just contains
garbage on the stack, so the freeing will cause issues when the
urb, buf and dma fields are free'd. Fix this by not free'ing the
dma_buf if the ivp allocation fails.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the missing spaces issue in coding style.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes spaces before commas issue in coding style.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch fixes the incorrect indentation of the case label.
Signed-off-by: Ujjal Roy <royujjal@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add USB ID 0411:01fd for Buffalo WLI-UC-G450 wireless adapter,
RT chipset 3593
Signed-off-by: Anthony Wong <anthony.wong@ubuntu.com>
Cc: stable@vger.kernel.org
Acked-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
multiport address flag(0x1000) should not be set during sdio cmd53,
if we have only one packet to read/write.
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch sdio multi port aggregation statistics which can be
used for debugging. This debug data is collected in
/sys/kernel/debug/mwifiex/mlan0/debug.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch corrects the error case in association path by returning
-1. Earlier "media_connected" used to remain on in this error case
causing failure for further association attempts.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Fixes: b887664d88 ('mwifiex: channel switch handling for station')
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It is observed that driver may send the data packet to tdls peer
before tdls peer receives tdls setup confirm frame.
Similar race condition exists during tdls teardown procedure also.
This patch adds 10 milliseconds delay to resolve the race.
Signed-off-by: Xinming Hu <huxm@marvell.com>
Signed-off-by: Cathy Luo <cluo@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
passing rtl_stats by value is inefficient; the structure is over 300
bytes in size and generally just one field (packet_report_type)
is being accessed, so the pass by value is a relatively large overhead.
This change just affects just the rx_command_packet calls.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is no need in usb_put_dev() if at76_load_internal_fw() succeed.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Introduce the use of to_delayed_work() helper function instead of open
coding it with container_of()
A simplified version of the Coccinelle semantic patch used to make
this change is:
//<smpl>
@@
expression a;
symbol work;
@@
- container_of(a, struct delayed_work, work)
+ to_delayed_work(a)
//</smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Reviewed-by: Julian Calaby <julian.calaby@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add full support for both AP and STA for management frame protection.
Reviewed-by: Arend Van Spriel <arend.van@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
brcmf_add_keyext is called when a key is configured for a specific
mac address. This function is very similar to the calling function
brcmf_add_key. Integrate this function and also use existing del_key
function in case key is to be cleared.
Reviewed-by: Arend Van Spriel <arend.van@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <franky.lin@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com>
Signed-off-by: Hante Meuleman <hante.meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Merge module parameters and platform data in one struct. This is the
last step to move to the new platform data per device. Now parameters
of platform data will be merged with module parameters per device.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Platform data is only available for sdio. With this patch a new
platform data structure is being used which allows for platform
data for any device and configurable per device. This patch only
switches to the new structure and adds support for SDIO devices.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently ARP and ND (IPv6 Neigbor Discovery) offload get disabled
on entering suspend. However when firmwares support the wowl_cap
iovar then these offload routines can be kept enabled as they
will work during WOWL as well.
Reviewed-by: Arend Van Spriel <arend@broadcom.com>
Reviewed-by: Franky (Zhenhui) Lin <frankyl@broadcom.com>
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: Hante Meuleman <meuleman@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
