It was found to be buggy on a variety of chipsets from AR913x to AR928x.
The new version (which was introduced along with AR93xx support) is more
reliable in preventing connectivity dropouts and also fixes MIB interrupt
storm issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beacon RSSI is only meaningful in station mode - in ad-hoc mode it
fluctuates, depending on which peer last sent a beacon, and in other
modes it is not set at all.
Fix places in ANI where the beacon RSSI is used to limit their use
to station mode only.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Code using this had already triggered smatch complaints, so remove it before
it gets fixed the wrong way.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_hw: improve ANI processing and rx desensitizing parameters"
was unifying some code related to overriding OFDM weak signal detection,
but seems to have gotten some of the original intent wrong, probably
because of a misnamed variable.
The beacon RSSI is only valid in station mode, and the main reason to check
it in ath9k_hw_set_ofdm_nil is to make sure that OFDM weak signal detection
stays enabled if the RSSI is low, even when the OFDM noise immunity entry
is supposed to disable it.
The above commit removed the mode checks and changed the code so that
OFDM weak signal detection would only be changed if the rssi is high, which
is wrong for everything but client mode.
This patch restores the old behavior in a simplified form.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I don't know why somebody decided to keep a cached copy of beacon rssi in a
variable called 'noiseFloor', but the caching is unnecessary and the variable
name is confusing, so let's just get rid of it entirely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the change "mac80211: remove spurious BSSID change flag",
BSS_CHANGED_BSSID will not be passed on association or IBSS
status changes. So it could be better to program bssid on ASSOC
or IBSS change notification. Not doing so, is affecting the
packet transmission.
Cc: stable@vger.kernel.org [3.4+]
Reported-by: Michael Leun <lkml20120218@newton.leun.net>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"ath9k: Fix softlockup in AR9485" with commit id
64bc1239c7 fixed the reported
issue, yet its better to avoid the possible infinite loop
in ar9003_get_pll_sqsum_dvc by having a timeout as suggested
by ath9k maintainers.
http://www.spinics.net/lists/linux-wireless/msg92126.html.
Based on my testing PLL's locking measurement is done in
~200us (2 iterations).
Cc: stable@vger.kernel.org
Cc: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After setup_frame_info has been called, only info->control.rates is still
valid, other control fields have been overwritten by the ath_frame_info
data. Move the access to info->control.vif for checking short preamble
to setup_frame_info before it gets overwritten.
This regression was introduced in commit d47a61aa
"ath9k: Fix multi-VIF BSS handling"
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Thomas Hühn <thomas@net.t-labs.tu-berlin.de>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Cc: stable@vger.kernel.org [3.4]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rate pointer variable for a rate series is used in a loop before it is
initialized. This went unnoticed because it was used earlier for the RTS/CTS
rate. This bug can lead to the wrong PHY type being passed to the
duration calculation function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
remove MCI_STATE_BT and use bt_state instead.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As p_data is unuse, lets remove it from ar9003_mci_state.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a MCI util function to send wlan channel info to BT.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add a utility function to set bluetooth version and remove
MCI_STATE_SET_BT_COEX_VERSION.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add utility functions to get and test GPM offset and
remove MCI_STATE*_GPM_OFFSET states.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Reset duty cycle before updating btcoex scheme. Otherwise duty cycle
reaches max limit and never be reduced again
* Adjust duty cycle with proper BDR profile value
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As btcoex scheme updation might sleep, remove the function call
from tasklet context and queue it up as a separate work.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
btcoex periord is converted into micro seconds during initialization
and converted back to milli seconds while starting timer. As MCI code
handles btcoex period in msec, lets keep the btcoex timer in msec and
convert them into other form whenever needed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies profile management utility functions.
* Separate find_profile from add/del functions
* Return correct values when the profile list is empty or
profile is ot found
* flush the profiles when there are entries in the list
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
let us process MCI interrupts only when BTCOEX is enabled to avoid
processing bogus interrupts.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a full reset, mci_reset will put LNA update to the setting
for 2G mode. Those registers need to be forced to update when
the channel is in 5G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both "MAC Warm Reset" and "MCI Reset Rx" will reset GPM HW write_ptr.
We should check software cached write_ptr against HW write_ptr before
reset. Otherwise the pending DMA data will be lost.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The HW statemachine is sometimes found stuck in the state
WL_LNA_CTRL_DISABLE when BT is in sleep, which will cause
TX_HOLD always asserted and resmgr stuck in PENDING_TX state
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so, could cause imbalance in powersave count.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Choose legacy rate as the last rate of Multi Rate Retry series
if and only if the last selected rate is MCS and having higher
PER rate. The current code fills a legacy rate as last one even
though the previous rates in the series are having good PER value.
This could limit the aggregation that affects the uplink performance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adjust quick_drop value in the baseband AGC register to
improve RX in HT20 mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
steps to recreate:
load latest ath9k driver with AR9485
stop the network-manager and wpa_supplicant
bring the interface up
Call Trace:
[<ffffffffa0517490>] ? ath_hw_check+0xe0/0xe0 [ath9k]
[<ffffffff812cd1e8>] __const_udelay+0x28/0x30
[<ffffffffa03bae7a>] ar9003_get_pll_sqsum_dvc+0x4a/0x80 [ath9k_hw]
[<ffffffffa05174eb>] ath_hw_pll_work+0x5b/0xe0 [ath9k]
[<ffffffff810744fe>] process_one_work+0x11e/0x470
[<ffffffff8107530f>] worker_thread+0x15f/0x360
[<ffffffff810751b0>] ? manage_workers+0x230/0x230
[<ffffffff81079af3>] kthread+0x93/0xa0
[<ffffffff815fd3a4>] kernel_thread_helper+0x4/0x10
[<ffffffff81079a60>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815fd3a0>] ? gs_change+0x13/0x13
ensure that the PLL-WAR for AR9485/AR9340 is executed only if the STA is
associated (or) IBSS/AP mode had started beaconing. Ideally this WAR
is needed to recover from some rare beacon stuck during stress testing.
Before the STA is associated/IBSS had started beaconing, PLL4(0x1618c)
always seem to have zero even though we had configured PLL3(0x16188) to
query about PLL's locking status. When we keep on polling infinitely PLL4's
8th bit(ie check for PLL locking measurements is done), machine hangs
due to softlockup.
fixes https://bugzilla.redhat.com/show_bug.cgi?id=811142
Reported-by: Rolf Offermanns <rolf.offermanns@gmx.net>
Cc: stable@vger.kernel.org [3.0+]
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MSI is enabled by default for most of the 4th generation
chips. Add this for AR9462 - this fixes PowerSave operation,
the chip was not entering Network-Sleep mode earlier.
With proper powering down of the MAC now, power consumption
in associated state is reduced considerably.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
'cfg80211: fix interface combinations' ensures that if an interface
type is not advertised by the driver in any of the interface combinations
(via ieee80211_iface_combination) then it shall be treated as a single
incompatible interface. if there are more than one interfaces present
and changing them to incompatible interface type is not possible.
These checks will be properly handled by cfg80211_change_iface ->
cfg80211_can_change_interface.
this patch is dependent on 'cfg80211: fix interface combinations'
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch is dependent on the patch "cfg80211: fix interface
combinations"
In ath9k currently we have ADHOC interface as a single incompatible
interface. when drv_add_interface is called during resume we got to
consider number of vifs already present in addition to checking the
drivers 'opmode' information about ADHOC. we incorrectly assume
an ADHOC interface is already present. Then we may miss some driver
specific data for the ADHOC interface after resume.
The above mentioned checks can be removed from the driver,
as the patch 'cfg80211: fix interface combinations' ensures that
if an interface type is not advertised by the driver in any of the
interface combinations(via ieee80211_iface_combination) then it shall
be treated as a single incompatible interface. Fixes the following
warning on suspend/resume with ibss interface.
ath: phy0: Cannot create ADHOC interface when other
interfaces already exist.
WARNING: at net/mac80211/driver-ops.h:12
ieee80211_reconfig+0x1882/0x1ca0 [mac80211]()
Hardware name: 2842RK1
wlan2: Failed check-sdata-in-driver check, flags: 0x0
Call Trace:
[<c01361b2>] warn_slowpath_common+0x72/0xa0
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<f8aaa7c2>] ? ieee80211_reconfig+0x1882/0x1ca0
[mac80211]
[<c0136283>] warn_slowpath_fmt+0x33/0x40
[<f8aaa7c2>] ieee80211_reconfig+0x1882/0x1ca0 [mac80211]
[<c06c1d1a>] ? mutex_lock_nested+0x23a/0x2f0
[<f8a95097>] ieee80211_resume+0x27/0x70 [mac80211]
[<fd177edf>] wiphy_resume+0x8f/0xa0 [cfg80211]
Cc: stable@vger.kernel.org
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After a chip reset, the beacon timers have to re-programmed
correctly for a station in associated state. Use the PS flags
to ensure that this is done after a TSF sync happens, otherwise
the driver ends up using incorrect values for TBTT/DTIM in
powersave mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ps_flags' is used/accessed in a variety of contexts
and requires proper locking. Use 'sc_pm_lock' appropriately.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a fatal interrupt is received or it is detected that the baseband
has hung, the chip has to be reset immediately. Otherwise, we end up
processing spurious interrupts. Ensure that we bail out properly in
the ISR when the reset work hasn't completed yet.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'sc_flags' variable is being used in a number of places
with no locking whatsoever. This patch converts the usage
of sc_flags to atomic ops.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And use a helper function to setup antennae after a reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Currently, there is no synchronization between the reset
work and the tx-poll work. Fix this and make sure that we
bail out properly if a reset work is in progress.
* Cleanup the PLL WAR and enable it for AR9340 too and
use a helper for restarting work/timers after a reset.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add link.c and move all the link/connection monitoring
code to it.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When BT FTP/PAN transmits while WLAN is idle, the one of 9462 chain
often picks up BT's tx signal and starts receiving. If the current
weight is set to be higher than BT tx, BT tx will be aborted and this
also degrades BT performance. Hence lower WLAN rx priority in this
case only when there are no WLAN traffic.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Program MCI related power registers only if MCI interrupts
are enabled. This could help to reduce power consumptions when
WLAN alone is enabled in BT coex chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is waking up from sleep state, the cycle counters
might have incorrect readings. So it is better not to update those
readings with software counters.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use smaller aggregation limit and increasing aggregation threshold
for osla that could improve wlan performance when there is HID profile.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When software rfkill is triggered, before put the chip in reset
state, give LNA and SPDT control to BT to make sure BT can have
good RF performance.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable WLAN and BT mode for switching regulator discontinuous
orverride for AR9462 chips.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
program BT to control SPDT everytime while loading switch table
from eeprom.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The chain index to perform IQ calibration is counted to number of valid
tx chains and then used for indexing chain specific registers. If the
chainmask is set to 0x2 (i.e chain 1 only), still it accesses chain 0
registers for chain 1. So use real chain index instead sequential one.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix bad indentation & if nesting to lose about two levels
of unnecessary indentation.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wrong ADC sample phase that happen between awake and
network/full sleep will lead to improper rx noisefloor
calibration.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also, use atomic operations to check the flags.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211's IEEE80211_CONF_OFFCHANNEL can be used directly
to track offchannel state. Also pass the correct boolean
value to ath9k_hw_startpcureceive().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Exposed by sparse:
ar9003_mci.c:1134:31: warning: Using plain integer as NULL pointer
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'setChip' variable is unused, remove it and
simplify the functions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MCI has to be handled only when BTCOEX is actually enabled.
Check for this condition before calling MCI related functions
from various reset/calibration call-sites.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default value that is being programmed to AR_RTC_KEEP_AWAKE
is 0x2, there is no need to program it manually in various
functions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
MCI interrupts have to be enabled only when BTCOEX is
actually in use.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ASPM has to be disabled when BTCOEX is in use, do this properly
by calling the bus-specific ASPM init routine after the
BTCOEX scheme has been determined.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of cluttering ath9k_init_device() with 'ath_softc'
specific initialization code, use ath9k_init_softc() to
setup driver-specific work routines, timers etc.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure CWmin based on slot time for IBSS mode. This helps
in increasing the beacon distribution of ath9k to accepted
levels in 11a mode.
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Updates for spectral scanning register modification for AR93x:
* fix bits for spectral_scan_count
* add bits for new parameters
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force, __iomem and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
Neatened the mwifiex_deauthenticate_infra function which
was doing odd things with array pointers and not using
is_zero_ether_addr.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This returns many of the values that formerly could
only be obtained from debugfs. This should be an
improvement when trying to access these counters
programatically. Currently this support is only
enabled when DEBUGFS is enabled because otherwise
these stats are not accumulated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we provide excess buffer size for 'simple_read_from_buffer'
for modal EEPROM dump. This results in trailing NULL bytes
at the end of EEPROM dump, fix this.
Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Reported-by: Holger Schurig <holgerschurig@googlemail.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Tested-by: Holger Schurig <holgerschurig@gogglemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On AR933x, the internal regulator settings need to be applied before the
PLL init to avoid stability issues.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"> Can you provide more information about the issues with high power devices?
Tx being flakey and Rx not working at all."
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_tx_setup_buffer() can fail if there is no ath_buf left, or if mapping DMA
failed. In this case it frees the skb passed to it.
If ath_tx_setup_buffer is called from ath_tx_form_aggr, the skb is still
linked into the tid buffer list and must be dequeued before being released.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It has been found that active Rx can interfere with stopping tx DMA, which
could result in at least parts of those "Failed to stop Tx DMA!" messages.
Stopping rx before tx should prevent that.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as well.
We deleted a staging driver, which was nice, and finally dropped the
obsolete usbfs code, which will make Al happy to never have to touch
that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were due
to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7qs0ACgkQMUfUDdst+ymjOgCfeoWqWk1bsKKt6SZULvQois5i
3csAn1Uapcm8Uswwpnj2v1/2Zh4rBHLA
=4jM1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB 3.5-rc1 changes from Greg Kroah-Hartman:
"Here is the big USB 3.5-rc1 pull request for the 3.5-rc1 merge window.
It's touches a lot of different parts of the kernel, all USB drivers,
due to some API cleanups (getting rid of the ancient err() macro) and
some changes that are needed for USB 3.0 power management updates.
There are also lots of new drivers, pimarily gadget, but others as
well. We deleted a staging driver, which was nice, and finally
dropped the obsolete usbfs code, which will make Al happy to never
have to touch that again.
There were some build errors in the tree that linux-next found a few
days ago, but those were fixed by the most recent changes (all were
due to us not building with CONFIG_PM disabled.)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (477 commits)
xhci: Fix DIV_ROUND_UP compile error.
xhci: Fix compile with CONFIG_USB_SUSPEND=n
USB: Fix core compile with CONFIG_USB_SUSPEND=n
brcm80211: Fix compile error for .disable_hub_initiated_lpm.
Revert "USB: EHCI: work around bug in the Philips ISP1562 controller"
MAINTAINERS: Add myself as maintainer to the USB PHY Layer
USB: EHCI: fix command register configuration lost problem
USB: Remove races in devio.c
USB: ehci-platform: remove update_device
USB: Disable hub-initiated LPM for comms devices.
xhci: Add Intel U1/U2 timeout policy.
xhci: Add infrastructure for host-specific LPM policies.
USB: Add macros for interrupt endpoint types.
xhci: Reserve one command for USB3 LPM disable.
xhci: Some Evaluate Context commands must succeed.
USB: Disable USB 3.0 LPM in critical sections.
USB: Add support to enable/disable USB3 link states.
USB: Allow drivers to disable hub-initiated LPM.
USB: Calculate USB 3.0 exit latencies for LPM.
USB: Refactor code to set LPM support flag.
...
Conflicts:
arch/arm/mach-exynos/mach-nuri.c
arch/arm/mach-exynos/mach-universal_c210.c
drivers/net/wireless/ath/ath6kl/usb.c
Hub-initiated LPM is not good for USB communications devices. Comms
devices should be able to tell when their link can go into a lower power
state, because they know when an incoming transmission is finished.
Ideally, these devices would slam their links into a lower power state,
using the device-initiated LPM, after finishing the last packet of their
data transfer.
If we enable the idle timeouts for the parent hubs to enable
hub-initiated LPM, we will get a lot of useless LPM packets on the bus
as the devices reject LPM transitions when they're in the middle of
receiving data. Worse, some devices might blindly accept the
hub-initiated LPM and power down their radios while they're in the
middle of receiving a transmission.
The Intel Windows folks are disabling hub-initiated LPM for all USB
communications devices under a xHCI USB 3.0 host. In order to keep
the Linux behavior as close as possible to Windows, we need to do the
same in Linux.
Set the disable_hub_initiated_lpm flag for for all USB communications
drivers. I know there aren't currently any USB 3.0 devices that
implement these class specifications, but we should be ready if they do.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: Marcel Holtmann <marcel@holtmann.org>
Cc: Gustavo Padovan <gustavo@padovan.org>
Cc: Johan Hedberg <johan.hedberg@gmail.com>
Cc: Hansjoerg Lipp <hjlipp@web.de>
Cc: Tilman Schmidt <tilman@imap.cc>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Petko Manolov <petkan@users.sourceforge.net>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: "Luis R. Rodriguez" <mcgrof@qca.qualcomm.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Cc: Christian Lamparter <chunkeey@googlemail.com>
Cc: Brett Rudley <brudley@broadcom.com>
Cc: Roland Vossen <rvossen@broadcom.com>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: "Franky (Zhenhui) Lin" <frankyl@broadcom.com>
Cc: Kan Yan <kanyan@broadcom.com>
Cc: Dan Williams <dcbw@redhat.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Cc: Ivo van Doorn <IvDoorn@gmail.com>
Cc: Gertjan van Wingerde <gwingerde@gmail.com>
Cc: Helmut Schaa <helmut.schaa@googlemail.com>
Cc: Herton Ronaldo Krzesinski <herton@canonical.com>
Cc: Hin-Tak Leung <htl10@users.sourceforge.net>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Chaoming Li <chaoming_li@realsil.com.cn>
Cc: Daniel Drake <dsd@gentoo.org>
Cc: Ulrich Kunitz <kune@deine-taler.de>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
This patch fixes multiple issues with the current RTT
implementation in ath9k.
* The data that is obtained from the RTT interface registers
are stored in 31:5 - mask out the extra bits when reading them.
* A history buffer is maintained which is not needed at all.
Remove this array and just store the baseband data for each
chain (or bank).
* A 'num_readings' variable was being used to handle the
last entry. But it was being used in an improper manner, with
the result that the RTT values were never being written
to the RTT Interface registers. Fix this by using a simple
flag.
* Stop baseband operations before programming the calibration values
to the HW.
* Do not restore RX gain settings as part of RTT.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit a844adfd7b.
The commit a844adfd is degrading rx sensitivity of lower rate in
HT40 mode and it is confirmed that reverting the change is
improving rx sensitivity.
spur_freq_sd (for self-corr in AGC) is defined with respect to the
center of each 20MHz channel while spur_phase_delta (for self-corr
in Rx and spur data filter) is defined with respect to the center
of current RF channel.
So in short, we need to subtract spur_freq_sd (for self-corr in AGC)
by the offset between the center of primary20 and the center of RF
channel in SW. This offset could be +/10 MHz for dynamic 40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Kai Shi <kaishi@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* PS_WAIT_FOR_TX_ACK is used in network-sleep mode and checking
it for handling IDLE transitions is incorrect. Fix this.
* RX PCU/DMA engines have to be stopped before setting the chip into
full-sleep mode - otherwise the chip becomes mute.
* Make things a bit clear by checking explicitly for network-sleep
mode in the tx() routine and add a couple of debug statements
to aid PS debugging.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix merge between commit 3adadc08cc ("net ax25: Reorder ax25_exit to
remove races") and commit 0ca7a4c87d ("net ax25: Simplify and
cleanup the ax25 sysctl handling")
The former moved around the sysctl register/unregister calls, the
later simply removed them.
With help from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend debugfs entry for dfs_stats with DFS detection events
and shared pool statistics.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix the following bug: in tkip mode, qos-null ps on/off packets
are dropped due to incorrect packet length so that ath9k softap
can't handle powersave state transition of peer STA correctly.
Signed-off-by: Michael Liang <mliang@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It does not work properly and reduces throughput.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The delay calculation is the same for all chips, however some parts of the
code missed the extra delay factor for half/quarter.
Clean up the code and move the delay calculation to a common place.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For some reason the MAC timing is a bit off when waiting for ACKs, so add
some extra delay to the ACK timeout values. Significantly reduces the
number of retransmissions in my tests.
Also disable the 2.4 GHz ACK timeout workaround in half/quarter mode, it
is not required there.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9462 uses modified version of 3-Wire hw scheme for btcoex.
MCI itself is not a separate hw scheme but it aids to manage
multiple bt profiles. In ar9462, bt priority traffic is identified
by the number of bt profile types instead of gpio. So that this
patch removes MCI hw scheme.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As of now beacon configuration is being called multiple times
in bss info change notification. This patch avoids multiple
configuration and make it simpler.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds locking of the detector's shared pulse and PRI sequence
pools to enable multi-wiphy operation on SMP systems.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current code unconditionally reads the target
power values for all modes from the EEPROM. However
In 'ar9003_hw_set_power_per_rate_table' the regulatory
caps are applied only on a mode specific subset of the
power values.
The reported TX power level is calculated from the
maximum of the power values. Because some of these
values are uncapped in certain cases, the reported
TX power will be wrong.
On the older chipset, we don't have such problems
because only the mode specific subset of the power
levels are retrieved from the EEPROM on those. Do
the same for the AR9003 chips to fix the issue.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes two compile warnings, and removes a useless
cast when assigning the 'sc' variable.
Reported-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ath9k_hw_update_regulatory_maxpower'
helper function has been introduced by
commit a55f858852
(ath9k_hw: Cleanup TX power calculation for AR9287).
Updating of the max_power_level value has been moved
into the helper function in that change, however the
removed code from 'ath9k_hw_ar9287_set_txpower' has
not been replaced with a call of the new helper
function.
Due to that missing call, retrieving tx power for 2x2
and 3x3 chainmask is not handled properly. During the
calculation of the tx power for 2x2 and 3x3 chainmasks
the values are reduced. Those reductions must be
compensated during retrieving.
Fix this by adding the missing call of the helper
function.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to unifying regulatory limit handling
commit ca2c68cc7b
(ath9k_hw: clean up tx power handling) introduced
a new helper function 'ath9k_hw_apply_txpower',
and the direct calls of 'ah->eep_ops->set_txpower'
has been replaced by a call of the helper function.
This caused a change in the behaviour of the
'ath9k_hw_set_txpowerlimit' function. The purpose
of that function is to calculate and store the
rate txpower table and the regulatory limit without
touching the hardware registers. Before the commit,
the 'test' parameter of the function was passed to
the 'ah->eep_ops->set_txpower'. Now the calling of
the 'set_txpower' function happens indirectly through
'ath9k_hw_apply_txpower', so the 'test' argument of
the 'set_txpower' is always 'false'.
This patch restores the original behaviour of
'ath9k_hw_set_txpowerlimit' by adding a new
argument to 'ath9k_hw_apply_txpower.'
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The FBIN2FREQ macro and the ath9k_hw_fbin2freq function
does the same thing. Remove the macro, and use the inline
function instead.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both eeprom.c and ar9003_eeprom.c has an indentical
'ath9k_hw_fbin2freq' function. Move the function to
a common place and remove the duplicates.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The existing constants are used for reduction/increase
tx power level on devices with 2x2 and 3x3 chainmask.
Both reduction and increase must use the same value, so
it makes no sense to use separate constants for them.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assigning sequence number for frames without taking care
of the fragment field breaks transmission of fragmented frames.
Fix this by assigning the fragment number properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The computation of the scaled power value in
various eeprom files uses identical code. Move
that code into a helper function and use that
instead of code duplication.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The REDUCE_SCALED_POWER_BY_THREE_CHAIN symbol is
defined in different eeprom files, and the value
varies between the different files.
In eeprom_def.c and in ar9003_eeprom.c the value
of the symbol is 9, however the comments in these
files indicates the value should be 10*log10(3)*2
which is 9.54242509439325. Replace the the value
to 10 in these files.
Also add comments to eeprom_9287.c.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have a helper function for updating the max_power_level
value. Use that and remove the duplicated code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tx interrupt for beacon queue is configured only for edma chips.
As the edma chip does not support per descriptor interrupt, no need to
set INTREQ for every beacon descriptor. And also clear ps filter for
beacon frame.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever the reset work is queued up, do not generate beacon. And also
clear the beacon miss count once the beacon stuck was observed.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After the chip reset, the noise immunity levels are restored with
history values. If the immunity levels are lower than the defaults,
lets start with the optimal values.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sync-up ibss beacon timer with the beacon frame's timestamp. When the
node acts as joiner, it has to sync with the received beacon timestamp
instead of reading tsf from hw. As the hw tsf wont wont be update till
bssid is configured. This patch programs hw tsf with the received beacon
timestamp if beacon timers are yet to be configured.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Update AR9462 initval to fix unbalance beacon distribution
in Ad-Hoc network.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it's only called when beacons are stuck, move it to the SWBA handler
tasklet, to avoid doing redundant checks on every single interrupt.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
LED support is typically handled via system GPIO on these platforms.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Also tweak beacon response times for better stability with the shorter
timer intervals.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Report all defined sync_cause errors in debugfs
to aid with debugging.
Use a macro to print out the interrupts file contents
to decrease code duplication.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This hides some repetitive code, and will help if the
column widths ever need to change.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Ryan Roper <ryan.roper@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The MAX_TXPWR table for BTCOEX is not needed for AR9462.
Programming these values to the HW results in undesirable
behavior - for example, large number of delimiter/data
underruns are seen in AES-CCMP mode. Also, registers like
AR_PCU_MISC_MODE2 return 0xdeadbeef after the BTCOEX_MAX
power table is programmed to the HW, and frames being transmitted
end up being looped back to the RX engine, an example being beacon
frames in IBSS mode.
Remove this table for now - this fixes CCMP performance and general
IBSS usage.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware needs a reset to recover from full sleep. Issue this reset
directly in the ath9k_config call that turns off idle, otherwise tx
remains dead until the first channel change after the idle state change
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds counters in various places that can drop packets on
rx without otherwise incrementing a counter. It also counts
some non-error cases, such as becons and fragments received.
Should help with figuring out where packets are (and are not)
dropped.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This counts any failure during getting packets into
the DMA buffers, including out-of-memory, etc.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Follow updates in DFS pattern detector interface:
a) use given pulse event structure
b) adapt to boolean return value of add_pulse()
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This adds a DFS pattern detector to ath9k. It is fed with pulse events
by the radar pulse detector and reports in place whether a pattern
was detected. On detection, the result is reported as radar event to
the DFS management component in the upper layer.
Currently the ETSI DFS domain is supported with detector lines for
the patterns defined by EN-301-893 v1.5.1. Support for FCC and JP
will be added gradually.
To include the pattern detector, ath9k must be built with support
for DFS certified config flag set (CONFIG_ATH9K_DFS_CERTIFIED).
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Devices that have internal rate control need to be
notified when the bandwidth or SMPS state changes
just like external rate control algorithms get a
notification now.
Add this notification and clarify the change bits
while at it, the HT_CHANGED bit really meant only
bandwidth changed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel type argument to the rate_update()
callback isn't really the correct way to give
the rate control algorithm about the desired
RX bandwidth of the peer.
Remove this argument, and instead update the
STA capabilities with 20/40 appropriately. The
SMPS update done by this callback works in the
same way, so this makes the callback cleaner.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not all devices are really capable of implementing
remain-on-channel, even if it is implemented in SW,
as they can't necessarily deal with channel changes
while associated.
Remove the WIPHY_FLAG_HAS_REMAIN_ON_CHANNEL and add
it only if either the driver has remain_on_channel
implemented in the driver/device.
Also add it to all drivers that advertise P2P right
now since those definitely have to have it working.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a more current logging style.
Make sure all output is prefixed appropriately.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit c1afdaff90.
Users have reported connection failures in 3.3.1 and suspend/resume
failures in 3.4-rcX. Revert this commit for now - PS IDLE can be
fixed in a clean manner later on.
Cc: stable@vger.kernel.org
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the experiment with Azimuth ADEPT-n testbed where the APs transmit
power was reduced to 25% and the signal strength was futher attenuated
by 20dB and induced a path loss of ~7dB, the station was reporting
beacon losses and the following issue were observed.
* rx clear is stuck at low for more than 300ms
* dcu chain and complete state is stuck at one of the hang signature
This patch triggers the hang detection logic that recovers the chip
from any of the above conditions. As the issue was originally reported
in ChromeOs with AR9382 chips, this detection logic is enabled only for
AR9380/2 chips.
Cc: Paul Stewart <pstew@google.com>
Reported-by: Gary Morain <gmorain@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch improves ANI operations by switching among the immunity
levels based on PHY errors and beacon rssi which will adjust receiver
desensitizing parameters. The changes are
* Configure the Weak Signal Detection based on current immunity value.
* At highest OFDM immunity level poor performance was observed with
strong interference. By tuning the FIR step and spur immunity levels
and not changing any weak signal detection thresholds at any level
helped to improve the performance.
* ANI took long time to recover back to lower immunity levels on heavy
data load. As the listen time got reset to zero before reaching to
the 5x of aniperiod, the immunity level is not lowering back even
without any interference. This patch fix that.
Cc: Paul Stewart <pstew@google.com>
Cc: Susinder Gulasekaran <susinder@qca.qualcomm.com>
Signed-off-by: Suresh Chandrasekaran <csuresh@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge batch of fixes from Andrew Morton:
"The simple_open() cleanup was held back while I wanted for laggards to
merge things.
I still need to send a few checkpoint/restore patches. I've been
wobbly about merging them because I'm wobbly about the overall
prospects for success of the project. But after speaking with Pavel
at the LSF conference, it sounds like they're further toward
completion than I feared - apparently davem is at the "has stopped
complaining" stage regarding the net changes. So I need to go back
and re-review those patchs and their (lengthy) discussion."
* emailed from Andrew Morton <akpm@linux-foundation.org>: (16 patches)
memcg swap: use mem_cgroup_uncharge_swap fix
backlight: add driver for DA9052/53 PMIC v1
C6X: use set_current_blocked() and block_sigmask()
MAINTAINERS: add entry for sparse checker
MAINTAINERS: fix REMOTEPROC F: typo
alpha: use set_current_blocked() and block_sigmask()
simple_open: automatically convert to simple_open()
scripts/coccinelle/api/simple_open.cocci: semantic patch for simple_open()
libfs: add simple_open()
hugetlbfs: remove unregister_filesystem() when initializing module
drivers/rtc/rtc-88pm860x.c: fix rtc irq enable callback
fs/xattr.c:setxattr(): improve handling of allocation failures
fs/xattr.c:listxattr(): fall back to vmalloc() if kmalloc() failed
fs/xattr.c: suppress page allocation failure warnings from sys_listxattr()
sysrq: use SEND_SIG_FORCED instead of force_sig()
proc: fix mount -t proc -o AAA
Many users of debugfs copy the implementation of default_open() when
they want to support a custom read/write function op. This leads to a
proliferation of the default_open() implementation across the entire
tree.
Now that the common implementation has been consolidated into libfs we
can replace all the users of this function with simple_open().
This replacement was done with the following semantic patch:
<smpl>
@ open @
identifier open_f != simple_open;
identifier i, f;
@@
-int open_f(struct inode *i, struct file *f)
-{
(
-if (i->i_private)
-f->private_data = i->i_private;
|
-f->private_data = i->i_private;
)
-return 0;
-}
@ has_open depends on open @
identifier fops;
identifier open.open_f;
@@
struct file_operations fops = {
...
-.open = open_f,
+.open = simple_open,
...
};
</smpl>
[akpm@linux-foundation.org: checkpatch fixes]
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The commit "ath9k: Remove aggregation flags" changed how
nodes were being initialized. Use the HW HT cap bits
to initialize/de-initialize nodes, else we would be
accessing an uninitialized entry during a suspend/resume cycle,
resulting in a panic.
Reported-by: Justin P. Mattock <justinmattock@gmail.com>
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 0d95521ea7 (ath9k: use split rx buffers to get rid of order-1 skb
allocations) added in memory leak in error path.
sc->rx.frag should be cleared after the pskb_expand_head() call, or else
we jump to requeue_drop_frag and leak an skb.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jouni Malinen <jouni@qca.qualcomm.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: John W. Linville <linville@tuxdriver.com>
Cc: Trond Wuellner <trond@chromium.org>
Cc: Grant Grundler <grundler@chromium.org>
Cc: Paul Stewart <pstew@chromium.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we have downlink traffic alone and the station is going thru
bgscan, the client is out of operating channel for around 1000ms which
is too long. The mac80211 decides when to switch back to oper channel
based on tx queue, bad latency and listen time. As the station does not
have tx traffic, the bgscan can easily affect downlink throughput. By
reducing the listen time, it helps the associated AP to retain the
downstream rate.
Cc: Paul Stewart <pstew@google.com>
Tested-by: Gary Morain <gmorain@google.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently the maximum noise floor limit is set as too high (-60dB). The
assumption of having a higher threshold limit is that it would help
de-sensitize the receiver (reduce phy errors) from continuous
interference. But when we have a bursty interference where there are
collisions and then free air time and if the receiver is desensitized too
much, it will miss the normal packets too. Lets make use of chips
specific min, nom and max limits always. This patch helps to improve the
connection stability in congested networks.
Cc: stable@vger.kernel.org
Cc: Paul Stewart <pstew@google.com>
Tested-by: Gary Morain <gmorain@google.com>
Signed-off-by: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Program tx gain through iniModesTxGain like on AR9287
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
use iniModesFastClock for 5 ghz fast clock specific settings, and
iniAdditional for clock/chip specific initval overrides
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Program the ah->ini_japan2484 INI values which were left out by accident
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The ATH9K_HW_CAP_AUTOSLEEP check is bogus, the rx status area needs to be
cleared on all non-EDMA PCI/AHB based chipsets anyway.
Limit the memset to the rx status area to improve performance.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By checking for NR_CPUS, the compiler can optimize out register access
serialization code on non-SMP kernels
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The default antenna (as programmed by the INI file) is always 0 anyway.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Automatically set the ah->htc_reset_init on init and after PHY disable.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TXQ_FLAG_TXOKINT_ENABLE and TXQ_FLAG_TXERRINT_ENABLE are always set and
used together, and they share the same bitmask in enum ath9k_tx_queue_flags.
Simplify the code that tests for these flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 provides short preamble information and ERP protection
information on a per-BSS basis, which can be used. Remove flags
stored in the driver, which was incorrect since they were being used
in a global manner.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
SC_OP_TXAGGR and SC_OP_RXAGGR are not really needed.
The HT capabilities of the station and HW can be used instead.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The logic to determine whether to use FCC is a bit convoluted.
Use a small helper function to decide whether FCC is to be
used.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not needed and will not be used anyway since
unsupported interfaces are not allowed to be created.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to mask out SWBA/BMISS from the
interrupt mask in start().
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The check for PS_WAIT_FOR_TX_ACK was inverted, the hardware should only go
to full sleep if no tx is pending.
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mactime was being overwritten by the function ath9k_rx_skb_preprocess. Fixed by
memsetting rx_status in ath_rx_tasklet.
Signed-off-by: Ashok Nagarajan <ashok@cozybit.com>
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The proper place to configure bss info is at assoc notification. So that
ath9k continues to work if the supirous bssid notification will be
removed in future.
Cc: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tested in AR9462 Rev:2, both hardware capability flag are set
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On A-MPDU frames, the hardware only reports valid signal strength data for
the last subframe. The driver also mangled rx_stats->rs_rssi using the
ATH_EP_RND macro in a way that may make sense for ANI, but definitely
not for reporting to mac80211.
This patch changes the code to calculate the signal strength from the rssi
directly instead of taking the average value, and flag everything but
the last subframe in an A-MPDU to tell mac80211 to ignore the signal strength
entirely, fixing signal strength fluctuation issues reported by various
users.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Process rx status directly instead of separating the completion test from
the actual rx status processing.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The way this is implemented (simply storing the last value) is absolutely
worthless for debugging anything, and the same information is also available
through the MAC sample feature, so there's no point in keeping this around.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They're more expensive than some of the other debug options and only used
in very rare situations, so it sometimes makes sense to disable them while
leaving in debugfs support.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cold reset is more reliable for getting the hardware out of some specific
stuck states.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this does the same thing as the previous code
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
its better to zero initialize the 'valid_phy_rate_idx' array completely
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Not doing so could cause the tx status queue to overflow during longer
periods of time without non-beacon tx. These events are also required
for proper drv_tx_last_beacon handling.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since AR9003 uses a global tx status queue, processing tx status outside of
the regular tx tasklet is dangerous and messes up hardware/software
synchronization of tx status events.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The approach of this change is flawed, as it triggers tx status processing
from more callsites, yet the chips only have one global tx status queue.
Subsequent patches will properly fix the issue that this one tried to address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Conflicts:
drivers/net/ethernet/broadcom/tg3.c
Conflicts in the statistics regression bug fix from 'net',
but happily Matt Carlson originally posted the fix against
'net-next' so I used that to resolve this.
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous RX error checking was done exclusive-or for different error
types and caused DFS pulse events to be dropped when other error
flags (e.g. CRC) were set simultaneously.
This patch decouples PHY error processing from other types and ensures
that all pulses detected by HW are accounted by the pattern detector.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup whitespace, fix indentation and coding style.
Also remove debug messages that were flooding the log.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes indentation and the general coding style
in ar9003_mci.c. Also, minimize the amount of debug log
output generated by MCI.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
They are not needed since MCI will be enabled only for
AR9462 v2.0
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Use a separate function to enable/disable
OneStepLookAhead.
* Remove unnecessary hardware SREV checks.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ATH9K_BTCOEX_SUPPORT is now used by both ath9k and ath9k_htc
to enable BT coexistence. Fix Kbuild to allow this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the ability to remove BTCOEX support at compile time,
these checks are no longer needed.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since BTCOEX code can be compiled out cleanly now,
remove these checks.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_htc can also make use of CONFIG_ATH9K_BTCOEX_SUPPORT
to be compiled without BTCOEX support.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make use of CONFIG_ATH9K_BTCOEX_SUPPORT in ath9k_hw
to provide a clean way of compilation without BTCOEX
support.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch converts a few functions to static variants
and removes extraneous declarations.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves all the MCI-specific declarations that have been
dumped unceremoniously in hw.h to ar9003_mci.h
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch moves all the MCI-specific code in the main reset
function to helper functions.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Setting up the required scheme can be done as part of the
BTCOEX initialization path and it doesn't belong in
ath9k_hw_fill_cap_info() anyway.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch uses CONFIG_ATH9K_BTCOEX_SUPPORT to conditionally
compile btcoex-related code in the driver core.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
v1.0 chips are not available in the market.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change the descriptor length to 24 and explicitly
set the control field 23 to zero. Not doing so would
result in dropping of frames.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The LONG_SHIFT_SELECT offset is different for AR9462 from
the other chip families. Fix this.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using AR_SREV_* macros for setting up the chip-specific NF
values will make adding support for new chips hard. Use separate
macros for each chip. Currently, AR9462 has the same value for
all NF limits.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Validate the phyerr value against the max. size of the
statistics array properly.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dumping the RSSI information in the middle of error
statistics is a bit misleading. Move them to the end.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch merges the 'wiphy' and 'misc' debugfs files
and consolidates the information.
Information about the current channel and other HT parameters
can be obtained from both mac80211 and iw. Remove such
redundant data.
The reset statistics have been removed, they will be re-added in
a subsequent patch (in a new debugfs file).
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Comparing SHA1 checksums of the initval tables has shown that there are many
tables that are 100% identical.
iniBank{0,1,2,3,7} and iniBB_RfGain are shared by AR5416, AR913x, AR9160
iniBank6 is shared between AR5416 and AR9160
iniBank6TPC is shared between AR913x and AR9160
iniPcieSerdes is the same for all AR9002 based devices
The CCK FIR coefficients are shared between AR9271 and AR9287
Getting rid of those duplicates saves about 7.5k uncompressed (on MIPS).
For AR9003 and later there are some duplicates as well, but I've decided to
leave them in for now, as the initvals for those chips are still actively
maintained by QCA.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_set_channel is called from ath9k_config which already has proper
PS wrappers
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the corresponding code/logic was removed in
"ath9k: rework power state handling"
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Duplicate the data for iniAddac early on, to avoid having to do redundant
memcpy calls later. While we're at it, make AR5416 < v2.2 use the same
codepath. Fixes a reported crash on x86.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Magnus Määttä <magnus.maatta@logica.com>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rate control algorithms are supposed to stop processing when they
encounter a rate with the index -1. Checking for rate->count not being
zero is not enough.
Allowing a rate with negative index leads to memory corruption in
ath_debug_stat_rc().
One consequence of the bug is discussed at
https://bugzilla.redhat.com/show_bug.cgi?id=768639
Signed-off-by: Pavel Roskin <proski@gnu.org>
Cc: stable@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Booleans should not be compared to true or false
but be directly tested or tested with !.
Done via cocci script:
@@
bool t;
@@
- t == true
+ t
@@
bool t;
@@
- t != true
+ !t
@@
bool t;
@@
- t == false
+ !t
@@
bool t;
@@
- t != false
+ t
Signed-off-by: Joe Perches <joe@perches.com>
Reviewed-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the firmware was over 2G, it would cause memory corruption and the
system would die here. Obviously we all know the firmware isn't going
to be that large but static checkers get upset.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit adb5066 "ath9k_hw: do not apply the 2.4 ghz ack timeout
workaround to cts" reduced the hardware CTS timeout to the normal
values specified by the standard, but it turns out while it doesn't
need the same extra time that it needs for the ACK timeout, it
does need more than the value specified in the standard, but only
for 2.4 GHz.
This patch brings the CTS timeout value in sync with the initialization
values, while still allowing adjustment for bigger distances.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit b4a82a0 "ath9k_hw: fix interpretation of the rx KeyMiss flag"
fixed the interpretation of the KeyMiss flag for keycache based lookups,
however WEP encryption uses a static index, so KeyMiss is always asserted
for it, even though frames are decrypted properly.
Fix this by clearing the ATH9K_RXERR_KEYMISS flag if no keycache based
lookup was performed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@vger.kernel.org
Reported-by: Laurent Bonnans <bonnans.l@gmail.com>
Reported-by: Jurica Vukadin <u.ra604@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
all works need to be initialized before ieee80211_register_hw
to prevent mac80211 call backs such as drv_start, drv_config
getting started. otherwise we would queue/cancel works before
initializing them and it leads to kernel panic.
this issue can be recreated with the following script
in Chrome laptops with AR928X cards, with background scan
running (or) Network manager is running
while true
do
sudo modprobe -v ath9k
sleep 3
sudo modprobe -r ath9k
sleep 3
done
EIP: [<81040a47>] __cancel_work_timer+0xb8/0xe1 SS:ESP 0068:f6be9d70
---[ end trace 4f86d6139a9900ef ]---
Registered led device: ath9k-phy0
ieee80211 phy0: Atheros AR9280 Rev:2 mem=0xf88a0000,
irq=16
Kernel panic - not syncing: Fatal exception
Pid: 456, comm: wpa_supplicant Tainted: G D
3.0.13 #1
Call Trace:
[<81379e21>] panic+0x53/0x14a
[<81004a30>] oops_end+0x73/0x81
[<81004b53>] die+0x4c/0x55
[<81002710>] do_trap+0x7c/0x83
[<81002855>] ? do_bounds+0x58/0x58
[<810028cc>] do_invalid_op+0x77/0x81
[<81040a47>] ? __cancel_work_timer+0xb8/0xe1
[<810489ec>] ? sched_clock_cpu+0x81/0x11f
[<8103f809>] ? wait_on_work+0xe2/0xf7
[<8137f807>] error_code+0x67/0x6c
[<810300d8>] ? wait_consider_task+0x4ba/0x84c
[<81040a47>] ? __cancel_work_timer+0xb8/0xe1
[<810380c9>] ? try_to_del_timer_sync+0x5f/0x67
[<81040a91>] cancel_work_sync+0xf/0x11
[<f88d7b7c>] ath_set_channel+0x62/0x25c [ath9k]
[<f88d67d1>] ? ath9k_tx_last_beacon+0x26a/0x85c [ath9k]
[<f88d8899>] ath_radio_disable+0x3f1/0x68e [ath9k]
[<f90d0edb>] ieee80211_hw_config+0x111/0x116 [mac80211]
[<f90dd95c>] __ieee80211_recalc_idle+0x919/0xa37 [mac80211]
[<f90dda76>] __ieee80211_recalc_idle+0xa33/0xa37 [mac80211]
[<812dbed8>] __dev_open+0x82/0xab
Cc: <stable@vger.kernel.org>
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Tested-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
alloc failures use dump_stack so emitting an additional
out-of-memory message is an unnecessary duplication.
Remove the allocation failure messages.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
channelFlags doesn't contain the operating HT mode.
Use IS_CHAN_HT40 to determine if the current channel is
in HT40 mode.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch modifies ath9k_htc to load the needed
firmware in an asynchronous manner, fixing timeouts
that were introduced with the new udev changes.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Skip group keys configuration in hardware in order to make IBSS RSN work.
Keys will be managed using software.
Signed-off-by: Antonio Quartulli <ordex@autistici.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Documentation states that the KeyMiss flag is only valid if RxFrameOK is
unset, however empirical evidence has shown that this is false.
When KeyMiss is set (and RxFrameOK is 1), the hardware passes a valid frame
which has not been decrypted. The driver then falsely marks the frame
as decrypted, and when using CCMP this corrupts the rx CCMP PN, leading
to connection hangs.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: Fix invalid noisefloor reading due to channel update"
preserves the current channel noisefloor readings before updating
channel type at the same channel index. It is also updating the curchan
pointer. As survey updation is also referring curchan pointer to fetch
the appropriate index, which might leads to invalid memory access. This
patch partially reverts the change and stores the noise floor history
buffer before updating channel type w/o updating curchan.
Cc: stable@kernel.org
Cc: Gary Morain <gmorain@google.com>
Cc: Paul Stewart <pstew@google.com>
Reported-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
also remove an unused macro and a function declaration
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
