Add back some PIDs that were mistakingly remove when reverting commit
73228a0538 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.
Fixes: 63a901c06e ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: Lei Liu <lei35151@163.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The PHY configuration is stored in an opaque "config" field, but when
allocating the structure, its proper size needs to be known. In the case
of UTMI, the proper structure is tegra_utmip_config of which a local
variable already exists, so we can use that to obtain the size from.
Fixes the following warning from the sparse checker:
drivers/usb/phy/phy-tegra-usb.c:882:17: warning: expression using sizeof(void)
Fixes: 81d5dfe6d8 (usb: phy: tegra: Read UTMIP parameters from device tree)
Cc: stable@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Up to now, when endpoint addresses in descriptors were non-consecutive,
there were created redundant files, which could cause problems in kernel,
when user tried to read/write to them. It was result of fact that maximum
endpoint address was taken as total number of endpoints in function.
This patch adds endpoint descriptors counting and storing their addresses
in eps_addrmap to verify their cohesion in each speed.
Endpoint address map would be also useful for further features, just like
vitual endpoint address mapping.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the usb_pkt_pop(). If a gadget driver calls
usb_ep_dequeue(), this driver will call the usb_pkt_pop().
So, the usb_pkt_pop() should cancel the transaction.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the condition of is_done in usbhsf_dma_push_done().
This function will be called after a transmission finished by DMAC.
So, the function should check if the transmission packet is short packet
or not. Also the function should call try_run to send the zero packet
by the pio handler if the "*is_done" is not set. Otherwize, the
transaction will not finish if a gadget driver sets the "zero" flag
in a transmission.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch protects the mod->irq_bempsts and mod->irq_brdysts by
spin lock in the usbhs_status_get_each_irq() because other functions
will write them during spin lock. Otherwise, the driver will clears
the BRDYSTS and/or BEMPSTS wrongly, and then, the transaction will not
finish.
Also since the driver should use the INTSTS0 and BRDYSTS and BEMPSTS
as the same timing, the patch protects them.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some gadget drivers will call usb_ep_queue() more than once before
the first queue doesn't finish. However, this driver didn't handle
it correctly. So, this patch fixes the behavior of some
usbhs_pkt_handle using the "running" flag. Otherwise, the oops below
happens if we use g_ncm driver and when the "iperf -u -c host -b 200M"
is running.
Unable to handle kernel NULL pointer dereference at virtual address 00000000
pgd = c0004000
[00000000] *pgd=00000000
Internal error: Oops: 80000007 [#1] SMP ARM
Modules linked in: usb_f_ncm g_ncm libcomposite u_ether
CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 3.17.0-rc1-00008-g8b2be8a-dirty #20
task: c051c7e0 ti: c0512000 task.ti: c0512000
PC is at 0x0
LR is at usbhsf_pkt_handler+0xa8/0x114
pc : [<00000000>] lr : [<c0278fb4>] psr: 60000193
sp : c0513ce8 ip : c0513c58 fp : c0513d24
r10: 00000001 r9 : 00000193 r8 : eebec4a0
r7 : eebec410 r6 : eebe0c6c r5 : 00000000 r4 : ee4a2774
r3 : 00000000 r2 : ee251e00 r1 : c0513cf4 r0 : ee4a2774
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Clearly this was meant to be an include guard, but a trailing
underscore was missing. It has been this way since the file was
introduced in 0fe6f1d1 ("usb: udc: add Faraday fusb300 driver").
Fixes: 0fe6f1d1 ("usb: udc: add Faraday fusb300 driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
CPPI TX does not transmit ZLP for TX transfers which
- transfer size is multiple of EP packet size,
- and URB_ZERO_PACKET is set in urb->transfer_flags.
The fix is transmitting the ZLP using PIO mode after the CPPI TX is
done.
Validated using the following usbtest write case in MUSB host mode.
# testusb -t1 -c1
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The UAC2 function driver currently responds to all packets at all times
with wMaxPacketSize packets. That results in way too fast audio
playback as the function driver (which is in fact supposed to define
the audio stream pace) delivers as fast as it can.
Fix this by sizing each packet correctly with the following steps:
a) Set the packet's size by dividing the nominal data rate by the
playback endpoint's interval.
b) If there is a residual value from the calculation in a), add
it to a accumulator to keep track of it across packets.
c) If the accumulator has gathered at least the number of bytes
that are needed for one sample frame, increase the packet size.
This way, the packet size calculation will get rid of any kind of
imprecision that would otherwise occur with a simple division over
time.
Some of the variables that are needed while processing each packet
are pre-computed for performance reasons.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With packet sizes other than 512, payloads in the packets may wrap
around the ALSA dma buffer partially, which leads to memory corruption
and audible clicks and pops in the audio stream at the moment, because
there is no boundary check before the memcpy().
In preparation to an implementation for smaller and dynamically sized
packets, we have to address such cases, and copy the payload in two
steps conditionally.
The 'src' and 'dst' approach doesn't work here anymore, as different
behavior is necessary in playback and capture cases. Thus, this patch
open-codes the routine now.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add a simple container_of() wrapper to get a struct f_uac2_opts from a
struct struct audio_dev. Use it in two places where it is currently
open-coded.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In afunc_bind() and afunc_set_alt(), &uac2->pdev.dev are used multiple
times. Adding a short-hand for them makes lines shorter so we can
remove some line wraps.
No functional change.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Restructure some code to make it easier to read.
While at it, return -ENOMEM instead of -EINVAL if
usb_ep_alloc_request() fails, and omit the logging in such cases
(the mm core will complain loud enough).
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Flatten the start_transfer function by reversing the if condition and
returning early out of the function if everything went fine. It makes
the function look less complicated, at least to me, and easier to
understand.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit f226708(usb: gadget: composite: dequeue cdev->req before free it in
composite_dev_cleanup) fixed a bug: free the usb request(i.e. cdev->req) but
does not dequeue it beforehand. This fix is not proper enough because it
dequeues the request after free its data buffer, considering the hardware can
access the buffer's memory anytime before the request's complettion rountine
runs, and usb_ep_dequeue always call the complettion rountine before it returns,
so the best way is to dequeue the request before free its buffer.
Suggested-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If NO_DMA=y:
drivers/built-in.o: In function `usbhsg_dma_map_ctrl':
mod_gadget.c:(.text+0x53b226): undefined reference to `usb_gadget_map_request'
mod_gadget.c:(.text+0x53b242): undefined reference to `usb_gadget_unmap_request'
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/phy/phy-samsung-usb[2,3] drivers got replaced by
drivers/phy/phy-samsung-usb[2,3] ones and the old common Samsung
USB PHY code is no longer used.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/phy/phy-samsung-usb3 driver got replaced by
drivers/phy/phy-samsung-usb3 one and is no longer used.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
drivers/usb/phy/phy-samsung-usb2 driver got replaced by
drivers/phy/phy-samsung-usb2 one and is no longer used.
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Kamil Debski <k.debski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add simple driver for Medtronic CareLink USB devices.
Reported-by: Benjamin West <bewest@gmail.com>
Tested-by: Benjamin West <bewest@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use direct method for supported baud rates, otherwise use divisors.
Limit baud rate to 12 Mbaud with HX type.
This change has been tested to work with PL-2303HX at 115200, 500000,
1000000, 2000000, 2500000, 3000000 and 4000000 baud rates.
Signed-off-by: Lauri Hintsala <lauri.hintsala@bluegiga.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
This VID:PID is used for some Direct IP devices behaving
identical to the already supported 0F3D:68AA devices.
Cc: <stable@vger.kernel.org>
Reported-by: Lars Melin <larsm17@gmail.com>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Sierra Wireless Direct IP devices using the 68A3 product ID
can be configured for modes including a CDC ECM class function.
The known example uses interface numbers 12 and 13 for the ECM
control and data interfaces respectively, consistent with CDC
MBIM function interface numbering on other Sierra devices.
It seems cleaner to restrict this driver to the ff/ff/ff
vendor specific interfaces rather than increasing the already
long interface number blacklist. This should be more future
proof if Sierra adds more class functions using interface
numbers not yet in the blacklist.
Cc: <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device id for NOVITUS Bono E thermal printer.
Reported-by: Emanuel Koczwara <poczta@emanuelkoczwara.pl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add back some PIDs that were mistakingly remove when reverting commit
73228a0538 ("USB: option,zte_ev: move most ZTE CDMA devices to
zte_ev"), which apparently did more than its commit message claimed in
that it not only moved some PIDs from option to zte_ev but also added
some new ones.
Fixes: 63a901c06e ("Revert "USB: option,zte_ev: move most ZTE CDMA
devices to zte_ev"")
Reported-by: Lei Liu <lei35151@163.com>
Cc: stable <stable@vger.kernel.org>
Using $(PWD) breaks builds when make was invoked from outside
of the kernel tree.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces the use of the functions usb_endpoint_type and
usb_endpoint_num.
The Coccinelle semantic patch that makes these changes is as follows:
@@ struct usb_endpoint_descriptor *epd; @@
- (epd->bEndpointAddress & \(USB_ENDPOINT_NUMBER_MASK\|0x0f\))
+ usb_endpoint_num(epd)
@@ struct usb_endpoint_descriptor *epd; @@
- (epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\))
+ usb_endpoint_type(epd)
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Two simple test cases for interrupt endpoints are added to the usbtest.c file.
These are simple non-queued interrupt IN and interrupt OUT transfers. Currently,
only gadget zero is capable of executing the interrupt EP test cases. However,
extending the same to other gadgets is extremely simple and can be done
on-demand.
The two new tests added are
- Test 25: To verify Interrupt OUT transfer
- Test 26: To verify Interrupt IN transfer
Since the default value of wMaxPacketSize is set as 1024, so interrupt
IN transfers must be specified with the size parameter = multiple of
1024. Otherwise the default value (512) in the usbtest application fails
the transfer. See [RUN 4] for sample logs
The application logs (usbtest) and corresponding kernel logs are as
following:
[Run 1]
./testusb -a -c 10 -s 2048 -t 26 -v 511
usbtest 7-1:3.0: TEST 26: read 2048 bytes 10 times
[Run 2]
./testusb -a -c 10 -s 1024 -t 25 -v 511
usbtest 7-1:3.0: TEST 25: write 1024 bytes 10 times
[Run 3]
./testusb -a -c 10 -s 1098 -t 25 -v 511
usbtest 7-1:3.0: TEST 25: write 1098 bytes 10 times
[Run 4 - Failure case scenario]
./testusb -a -t 26
unknown speed /dev/bus/usb/007/004 0
/dev/bus/usb/007/004 test 26 --> 75 (Value too large for defined data type)
usbtest 7-1:3.0: TEST 26: read 512 bytes 1000 times
usb 7-1: test26 failed, iterations left 999, status -75 (not 0)
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Unfortunately, the USB gadget layer has this weird things where NULL
skbs are passed into ops->ndo_start_xmit() in order to trigger the
dev->wrap() calls to build packets.
This is completely outside of the allowable range of sane arguments
for the ndo_start_xmit method. All invocations of ndo_start_xmit()
should be with non-NULL SKB arguments.
Put back the direct call, but with a comment explaining how this
is not acceptable in the long term.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit bdd405d2a5 ("usb: hub: Prevent hub autosuspend if
usbcore.autosuspend is -1") causes a build error if CONFIG_PM_RUNTIME is
disabled. Fix that by doing a simple #ifdef guard around it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Michael Welling <mwelling@emacinc.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a bit bigger hammer then I would like to use for this, but for now
it will have to make do. I'm working on getting my hands on one of these so
that I can try to get streams to work (with a quirk flag if necessary) and
then we can re-enable them.
For now this at least makes uas capable disk enclosures work again by forcing
fallback to the usb-storage driver.
https://bugzilla.kernel.org/show_bug.cgi?id=79511
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to verify the number of ports requested by subdriver to avoid
writing beyond the end of fixed-size array in interface data.
The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of ports requested by a
subdriver (which could have been determined from device descriptors) did
not exceed this limit.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to verify the maximum number of endpoints per type to avoid
writing beyond the end of a stack-allocated array.
The current usb-serial implementation is limited to eight ports per
interface but failed to verify that the number of endpoints of a certain
type reported by a device did not exceed this limit.
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Interrupt endpoints behave quite similar to the bulk endpoints with the
difference that the endpoints expect data sending/reception request at
particular intervals till the whole data has not been transmitted.
The interrupt EP support is added to gadget zero. A new alternate setting (=2)
has been added. It has 2 interrupt endpoints. The default parameters are set as:
bInterval: 1 ms for FS and 8 uFrames (implying 1 ms) for HS/SS
wMaxPacketSize: 64 bytes for FS and 1024 bytes for HS/SS
However, the same can be overridden through the module parameter interface.
The code is tested for HS and SS on a platform having DWC3 controller.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the ttyGS PREFIX macro from u_serial.c and replace all occurences with
the hardcoded ttyGS string.
This macro was mostly used in a few debug/warning messages and a lot of
hardcoded ttyGS existed beneath. It may have been used for renaming the
tty, but if done so most debug messages would have ignored this.
Due to the fact the usage of this PREFIX in all debug calls would have
resulted in a hard to read/grep code it is removed completely.
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Replace the VDBG and DBG macro with the kernels "proper" debug macros
(dev_vdbg and dev_dbg) in f_acm.c, f_obex.c & f_serial.c
Signed-off-by: Richard Leitner <richard.leitner@skidata.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch makes the phy reset clk and reset line optional as this clk
is not available on boards like IFC6410 with APQ8064.
phy-reset clk is only used as argument to the mach level callbacks, so
this patch adds condition before clk_get calls so that the driver
wouldn't fail on SOCs which do not have this support.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds support for the USB PHY in Vybrid VF610. We assume that
the disconnection without VBUS is also needed for Vybrid.
Tests showed, without MXS_PHY_NEED_IP_FIX, enumeration of devices
behind a USB Hub fails with errors:
[ 215.163507] usb usb1-port1: cannot reset (err = -32)
[ 215.170498] usb usb1-port1: cannot reset (err = -32)
[ 215.185120] usb usb1-port1: cannot reset (err = -32)
[ 215.191345] usb usb1-port1: cannot reset (err = -32)
[ 215.202487] usb usb1-port1: cannot reset (err = -32)
[ 215.207718] usb usb1-port1: Cannot enable. Maybe the USB cable is bad?
[ 215.219317] usb usb1-port1: unable to enumerate USB device
Hence we also enable the MXS_PHY_NEED_IP_FIX flag.
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since we want to keep support for both older usb-phys as well as the
newer generic phys, lets first get the generic PHYs and fallback to
older USB-PHYs only when we fail to get the former.
This should fix the issue with ehci-exynos and ohci-exynos, wherein
in the absence of SAMSUNG_USB2PHY config symbol, we end up getting
the NOP_USB_XCEIV phy when the same is enabled. And thus the PHYs
are not configured properly.
Reported-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Jingoo Han <jg1.han@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If user specifies that USB autosuspend must be disabled by module
parameter "usbcore.autosuspend=-1" then we must prevent
autosuspend of USB hub devices as well.
commit 596d789a21 introduced in v3.8 changed the original behaivour
and stopped respecting the usbcore.autosuspend parameter for hubs.
Fixes: 596d789a21 "USB: set hub's default autosuspend delay as 0"
Cc: [3.8+] <stable@vger.kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Tested-by: Michael Welling <mwelling@emacinc.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I have a j5 create (JUA210) USB 2 video device and adding it device id
to SIS USB video gets it to work.
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the default EP max packet value as 8 bytes, because in the case
of low-speed, 'ep_mps' is not set. Thus, the default value of 'ep_mps'
should be considered for the case of low-speed.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The roothub's index per controller is from 0, but the hub port index per hub
is from 1, this patch fixes "can't find device at roohub" problem for connecting
test fixture at roohub when do USB-IF Embedded Host High-Speed Electrical Test.
This patch is for v3.12+.
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The uSCSI from Newer Technology is a SCSI-USB converter with USB ID 06ca:2003.
Like several other SCSI-USB products, it's a Shuttle Technology OEM device.
Without a suitable entry in unusual-devs.h, the converter can only access the
(single) device with SCSI ID 0. Copying the entry for device 04e6:0002 allows
it to work with devices with other SCSI IDs too.
There are currently six entries for Shuttle-developed SCSI-USB devices in
unusual-devs.h (grep for euscsi):
04e6:0002 Shuttle eUSCSI Bridge USB_SC_DEVICE, USB_PR_DEVICE
04e6:000b Shuttle eUSCSI Bridge USB_SC_SCSI, USB_PR_BULK
04e6:000c Shuttle eUSCSI Bridge USB_SC_SCSI, USB_PR_BULK
050d:0115 Belkin USB SCSI Adaptor USB_SC_SCSI, USB_PR_BULK
07af:0004 Microtech USB-SCSI-DB25 USB_SC_DEVICE, USB_PR_DEVICE
07af:0005 Microtech USB-SCSI-HD50 USB_SC_DEVICE, USB_PR_DEVICE
lsusb -v output for the uSCSI lists
bInterfaceSubClass 6 SCSI
bInterfaceProtocol 80 Bulk (Zip)
This patch adds an entry for the uSCSI to unusual_devs.h.
Signed-off-by: Mark Knibbs <markk@clara.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was used back when usbip-host was an interface device driver;
after the conversion to device driver, the table remained unused.
Remove it in order to stop receiving a warning about it.
Signed-off-by: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At this point, USB/IP kernel code is fully functional
and can be moved out of staging.
Signed-off-by: Valentina Manea <valentina.manea.m@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's our first set of fixes for v3.17-rc cycle. Most fixes are
pretty minor changes like the signedness bug in dwc3, or the wrong
string format on MUSB.
The most interesting part is the addition of Intel Quark X1000 support
to PCH UDC.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=Rb6u
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into work-linus
Felipe writes:
usb: fixes for v3.17-rc2
Here's our first set of fixes for v3.17-rc cycle. Most fixes are
pretty minor changes like the signedness bug in dwc3, or the wrong
string format on MUSB.
The most interesting part is the addition of Intel Quark X1000 support
to PCH UDC.
Signed-of-by: Felipe Balbi <balbi@ti.com>
This patch fixes a potential security issue in the whiteheat USB driver
which might allow a local attacker to cause kernel memory corrpution. This
is due to an unchecked memcpy into a fixed size buffer (of 64 bytes). On
EHCI and XHCI busses it's possible to craft responses greater than 64
bytes leading a buffer overflow.
Signed-off-by: James Forshaw <forshaw@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These updates fix the log level for some option log messages that started
bothering people after a recent change.
They also fix some issues reported against the zte_ev driver by moving most
device ids back from the zte_ev driver to the option driver (and removing two
duplicate ids). The zte_ev driver is planned to be removed in 3.18.
Some new device ids are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=e+RG
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.17-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into work-linus
Johan writes:
USB-serial fixes for v3.17-rc2
These updates fix the log level for some option log messages that started
bothering people after a recent change.
They also fix some issues reported against the zte_ev driver by moving most
device ids back from the zte_ev driver to the option driver (and removing two
duplicate ids). The zte_ev driver is planned to be removed in 3.18.
Some new device ids are also added.
Signed-off-by: Johan Hovold <johan@kernel.org>
As the driver is in mainline we can remove the version numbers.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If uvc->control_buf is successfuly allocated but uvc->control_req
is not, uvc->control_buf is not freed in the error recovery path.
With this patch applied uvc->control_buf is freed unconditionally;
if it happens to be NULL kfree on it is safe anyway.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Activate the videobuf2 DMABUF support. As vb2-vmalloc supports the
importer role only, exporting buffers isn't supported yet. When the
exporter role will be implemented in vb2-vmalloc the UVC gadget driver
will automatically gain support for it.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The disconnect of the USB Device is a common pattern for
an UVC Camera. In many cases this will give us an meaningless
information for all buffers that couldn't be enqueued.
That patch changes this to KERN_DEBUG.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for using f_uac1 function as a component of a gadget
composed with configfs.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When configfs support is added the values in question will have to be
used in two different places. Substitute them with defined constants
to avoid duplicating magic numbers.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new usb_gstring_attach interface.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no users of the old interface left, so it can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new interface so that the old one can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Converting uac1 to the new function interface requires converting
the USB uac1's function code and its users.
This patch converts the f_uac1.c to the new function interface.
The file is now compiled into a separate usb_f_uac1.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Integrating configfs requires converting f_uac1 to new function interface,
which in turn requires converting it to the new function interface,
which involves separate compilation of f_uac1.c into usb_f_uac1.ko.
u_uac1.c contains some module parameters. After this patch is applied
they are still a part of the resulting g_audio.ko, but can be guarded
with a compatiblity flag which will be removed when no users of the old
function interface of f_uac1 are left.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
uac1 function is missing strings. Add them.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for using f_uac2 function as a component of a gadget
composed with configfs.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When configfs is integrated the same values will have to be used
as defaults. Use symbolic names in order not to duplicate magic numbers.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new usb_gstring_attach interface.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There are no users of the old interface left, so it can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the new interface so that the old one can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Converting uac2 to the new function interface requires converting
the USB uac2's function code and its users.
This patch converts the f_uac2.c to the new function interface.
The file is now compiled into a separate usb_f_uac2.ko module.
The old function interface is provided by means of a preprocessor
conditional directives. After all users are converted, the old interface
can be removed.
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Eliminate static struct *agdev_g from f_uac2.c.
It is used for freeing its memory, but the same address can be found
by calling container_of in afunc_unbind(). This implies eliminating
uac2_unbind_config(). The audio_config_driver in audio.c does not have
its unbind method any more. It has been used only when uac2 is used,
so uac2 itself can handle unbinding in afunc_unbind().
Tested-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove unnecessary lines of register bit definitions in order
to enhance the readability. In this case, there are lines
per register offset definitions. There is no functional change.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The variable $(PWD) is useless, and it may break the compilation.
For example, it breaks the kernel compilation when it's done with
buildroot :
/home/trem/Codes/armadeus/armadeus/buildroot/output/host/usr/bin/ccache
/home/trem/Codes/armadeus/armadeus/buildroot/output/host/usr/bin/arm-buildroot-linux-uclibcgnueabi-gcc
-Wp,-MD,drivers/usb/gadget/legacy/.hid.o.d -nostdinc -isystem
/home/trem/Codes/armadeus/armadeus/buildroot/output/host/usr/lib/gcc/arm-buildroot-linux-uclibcgnueabi/4.7.3/include
-I./arch/arm/include -Iarch/arm/include/generated -Iinclude
-I./arch/arm/include/uapi -Iarch/arm/include/generated/uapi
-I./include/uapi -Iinclude/generated/uapi -include
./include/linux/kconfig.h -D__KERNEL__ -mlittle-endian -Wall -Wundef
-Wstrict-prototypes -Wno-trigraphs -fno-strict-aliasing -fno-common
-Werror-implicit-function-declaration -Wno-format-security
-fno-dwarf2-cfi-asm -mabi=aapcs-linux -mno-thumb-interwork -mfpu=vfp
-funwind-tables -marm -D__LINUX_ARM_ARCH__=5 -march=armv5te
-mtune=arm9tdmi -msoft-float -Uarm -fno-delete-null-pointer-checks -O2
--param=allow-store-data-races=0 -Wframe-larger-than=1024
-fno-stack-protector -Wno-unused-but-set-variable -fomit-frame-pointer
-fno-var-tracking-assignments -g -Wdeclaration-after-statement
-Wno-pointer-sign -fno-strict-overflow -fconserve-stack
-Werror=implicit-int -Werror=strict-prototypes -DCC_HAVE_ASM_GOTO
-I/home/trem/Codes/armadeus/armadeus/buildroot/drivers/usb/gadget/
-I/home/trem/Codes/armadeus/armadeus/buildroot/drivers/usb/gadget/udc/
-I/home/trem/Codes/armadeus/armadeus/buildroot/drivers/usb/gadget/function/
-DMODULE -D"KBUILD_STR(s)=#s" -D"KBUILD_BASENAME=KBUILD_STR(hid)"
-D"KBUILD_MODNAME=KBUILD_STR(g_hid)" -c -o
drivers/usb/gadget/legacy/hid.o drivers/usb/gadget/legacy/hid.c
drivers/usb/gadget/epautoconf.c:23:26: erreur fatale: gadget_chips.h :
Aucun fichier ou dossier de ce type
This compilation line include :
..../buildroot/driver/usb/gadget
but the real path is :
..../buildroot/output/build/linux-3.17-rc1/driver/usb/gadget
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch is to enable the USB gadget device for Intel Quark X1000
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@intel.com>
Signed-off-by: Bing Niu <bing.niu@intel.com>
Signed-off-by: Alvin (Weike) Chen <alvin.chen@intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the pending buffers in the queue could not be pushed to the udc
endpoint we have to cancel the uvc_queue. Otherwise the gadget will get
stuck on this error. This patch calls uvc_queue_cancel if usb_ep_queue
failed.
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
linux-2.6/drivers/usb/wusbcore/wa-xfer.c: In function 'wa_buf_in_cb':
linux-2.6/drivers/usb/wusbcore/wa-xfer.c:2590: warning: 'rpipe' may be used uninitialized in this function
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Suggested-by: Thomas Pugliese <thomas.pugliese@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
linux-2.6/drivers/usb/core/hub.c: In function 'usb_disconnect':
linux-2.6/drivers/usb/core/hub.c:2110: warning: 'hub' may be used uninitialized in this function
linux-2.6/drivers/usb/core/hub.c:2111: warning: 'port1' may be used uninitialized in this function
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
linux-2.6/drivers/usb/dwc2/gadget.c: In function 's3c_hsotg_irq_enumdone':
linux-2.6/drivers/usb/dwc2/gadget.c:1904: warning: 'ep_mps' may be used uninitialized in this function
Acked-by: Paul Zimmerman <Paul.Zimmerman@synopsys.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When we manually need to move the TR dequeue pointer we need to set the
correct cycle bit as well. Previously we used the trb pointer from the
last event received as a base, but this was changed in
commit 1f81b6d22a ("usb: xhci: Prefer endpoint context dequeue pointer")
to use the dequeue pointer from the endpoint context instead
It turns out some Asmedia controllers advance the dequeue pointer
stored in the endpoint context past the event triggering TRB, and
this messed up the way the cycle bit was calculated.
Instead of adding a quirk or complicating the already hard to follow cycle bit
code, the whole cycle bit calculation is now simplified and adapted to handle
event and endpoint context dequeue pointer differences.
Fixes: 1f81b6d22a ("usb: xhci: Prefer endpoint context dequeue pointer")
Reported-by: Maciej Puzio <mx34567@gmail.com>
Reported-by: Evan Langlois <uudruid74@gmail.com>
Reviewed-by: Julius Werner <jwerner@chromium.org>
Tested-by: Maciej Puzio <mx34567@gmail.com>
Tested-by: Evan Langlois <uudruid74@gmail.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
AMD xHC also needs short tx quirk after tested on most of chipset
generations. That's because there is the same incorrect behavior like
Fresco Logic host. Please see below message with on USB webcam
attached on xHC host:
[ 139.262944] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.266934] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.270913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.274937] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.278914] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.282936] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.286915] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.290938] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.294913] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
[ 139.298917] xhci_hcd 0000:00:10.0: WARN Successful completion on short TX: needs XHCI_TRUST_TX_LENGTH quirk?
Reported-by: Arindam Nath <arindam.nath@amd.com>
Tested-by: Shriraj-Rai P <shriraj-rai.p@amd.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using a Renesas uPD720231 chipset usb-3 uas to sata bridge with a 120G
Crucial M500 ssd, model string: Crucial_ CT120M500SSD1, together with a
the integrated Intel xhci controller on a Haswell laptop:
00:14.0 USB controller [0c03]: Intel Corporation 8 Series USB xHCI HC [8086:9c31] (rev 04)
The following error gets logged to dmesg:
xhci error: Transfer event TRB DMA ptr not part of current TD
Treating COMP_STOP the same as COMP_STOP_INVAL when no event_seg gets found
fixes this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit [5ee0f803cc: usbcore: don't log on consecutive debounce
failures of the same port] added the check of the reliable port, but
it also replaced the device argument to dev_err() wrongly, which leads
to a NULL dereference.
This patch restores the right device, port_dev->dev. Also, since
dev_err() itself shows the port number, reduce the port number shown
in the error message, essentially reverting to the state before the
commit 5ee0f803cc.
[The fix suggested by Hannes, and the error message cleanup suggested
by Alan Stern]
Fixes: 5ee0f803cc ('usbcore: don't log on consecutive debounce failures of the same port')
Reported-by: Hannes Reinecke <hare@suse.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function devm_ioremap_nocache() returns NULL
pointer not ERR_PTR(). The IS_ERR() test in the return value check
should be replaced with NULL test.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Acked-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case of error, the function memdup_user() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Felipe Balbi <balbi@ti.com>
"ret" should be signed. It's only used for zero and negative error
codes.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The prefix suggests the number should be printed in hex, so use
the %x specifier to do that.
Found by using regex suggested by Joe Perches.
Signed-off-by: Hans Wennborg <hans@hanshq.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
As, the interrupt for DMA is counted from 1, so need to checked
the USBA_NR_DMAS, in old way, it only check (USBA_NR_DMAS - 1),
so fix it.
Reported-by: Max Liao <liaops@embest-tech.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Convert a zero return value on error to a negative one, as returned
elsewhere in the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
{ ... return ret; }
|
ret = 0
)
... when != ret = e1
when != &ret
*if(...)
{
... when != ret = e2
when forall
return ret;
}
// </smpl>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Felipe Balbi <balbi@ti.com>
According to the datasheet, PHYPARAM1_PCS_TXDEEMPH is set as
6 bits [5:0]. Thus, the bit mask should be set as 0x3f, instead
of 0x1f.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
After dbgp_bind()-dbgp_unbind() cycle happens, static variable dbgp
contains pointers to already deallocated memory (dbgp.serial and dbgp.req).
If the next dbgp_bind() fails, for example in usb_ep_alloc_request(),
dbgp_bind() calls dbgp_unbind() on failure path,
and dbgp_unbind() frees dbgp.serial that still stores a pointer
to already deallocated memory.
The patch sets pointers to NULL in dbgp_unbind().
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using kfree to free data allocated with devm_kzalloc causes double frees.
The Coccinelle semantic patch that fixes this problem is as follows:
// <smpl>
@@
expression x;
@@
x = devm_kzalloc(...)
...
?-kfree(x);
// </smpl>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When __usb_find_phy_dev() does not return error and
try_module_get() fails, return -ENODEV.
Signed-off-by: Arjun Sreedharan <arjun024@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Added support to the ftdi_sio driver for ekey Converter USB which
uses an FT232BM chip.
Signed-off-by: Jaša Bartelj <jasa.bartelj@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This adds a new device id to the pl2303 driver for the ZTEK device.
Reported-by: Mike Chu <Mike-Chu@prolific.com.tw>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add device id for Basic Micro ATOM Nano USB2Serial adapters.
Reported-by: Nicolas Alt <n.alt@mytum.de>
Tested-by: Nicolas Alt <n.alt@mytum.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove dublicate Qualcom PID 0x3197 which is already handled by the
moto-modem driver since commit 6986a978ee ("USB: add new moto_modem
driver for some Morotola phones").
Fixes: 799ee9243d ("USB: serial: add zte_ev.c driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove dublicate Gobi PID 0x9008 which is already handled by the
qcserial driver since commit f05932c0ca ("USB: qcserial: Add extra
device IDs").
Fixes: 799ee9243d ("USB: serial: add zte_ev.c driver")
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This reverts commit 73228a0538 ("USB: option,zte_ev: move most ZTE
CDMA devices to zte_ev").
Move the IDs of the devices that were previously driven by the option
driver back to that driver.
As several users have reported, the zte_ev driver is causing random
disconnects as well as reconnect failures.
A closer analysis of the zte_ev setup code reveals that it consists of
standard CDC requests (SET/GET_LINE_CODING and SET_CONTROL_LINE_STATE)
but unfortunately fails to get some of those right. In particular, as
reported by Liu Lei, it fails to lower DTR/RTS on close. It also appears
that the control requests lack the interface argument.
Note that the zte_ev driver is based on code (once) distributed by ZTE
that still appears to originally have been reverse-engineered and bolted
onto the generic driver.
Since line control is already handled properly by the option driver, and
the SET/GET_LINE_CODING requests appears to be redundant (amounts to a
SET 9600 8N1), this is a first step in ultimately removing the redundant
zte_ev driver.
Note that AC2726 had already been moved back to option, and that some
IDs were in the device table of both drivers prior to the commit being
reverted.
Reported-by: Lei Liu <liu.lei78@zte.com.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This VIA Telecom baseband processor is used is used by by u-blox in both the
FW2770 and FW2760 products and may be used in others as well.
This patch has been tested on both of these modem versions.
Signed-off-by: Brennan Ashton <bashton@brennanashton.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Do not log normal interrupt-urb shutdowns as errors.
The option driver has always been logging any nonzero interrupt-urb
status as an error, including when the urb is killed during normal
operation.
Commit 9096f1fbba ("USB: usb_wwan: fix potential NULL-deref at
resume") moved the interrupt urb submission from port probe and release
to open and close, thus potentially increasing the number of these
false-positive error messages dramatically.
Reported-by: Ed Butler <ressy66@ausics.net>
Tested-by: Ed Butler <ressy66@ausics.net>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull trivial tree changes from Jiri Kosina:
"Summer edition of trivial tree updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (23 commits)
doc: fix two typos in watchdog-api.txt
irq-gic: remove file name from heading comment
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
scsi: mvsas: mv_sas.c: Fix for possible null pointer dereference
doc: replace "practise" with "practice" in Documentation
befs: remove check for CONFIG_BEFS_RW
scsi: doc: fix 'SCSI_NCR_SETUP_MASTER_PARITY'
drivers/usb/phy/phy.c: remove a leading space
mfd: fix comment
cpuidle: fix comment
doc: hpfall.c: fix missing null-terminate after strncpy call
usb: doc: hotplug.txt code typos
kbuild: fix comment in Makefile.modinst
SH: add proper prompt to SH_MAGIC_PANEL_R2_VERSION
ARM: msm: Remove MSM_SCM
crypto: Remove MPILIB_EXTRA
doc: CN: remove dead link, kerneltrap.org no longer works
media: update reference, kerneltrap.org no longer works
hexagon: update reference, kerneltrap.org no longer works
doc: LSM: update reference, kerneltrap.org no longer works
...
This patch set consists of the usual driver updates (ufs, storvsc, pm8001
hpsa). It also has removal of the user space target driver code (everyone is
using LIO now), a partial PCI MSI-X update, more multi-queue updates,
conversion to 64 bit LUNs (so we could theoretically cope with any LUN
returned by a device) and placeholder support for the ZBC device type (Shingle
drives), plus an assortment of minor updates and bug fixes.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJT4mS9AAoJEDeqqVYsXL0Mq34H/2AeXiM8GEVO3PIsBtF3TFZ9
poJvAyb8t//+VwAIVLHU9wrssIrIcyvNQmNHH/InGt5rOaXwGQRsnEc73bBtot4b
aC1t+hAnp2Ddvu6phmyUg7iY2GmQhAoZmeaj7krGIu2XgtLGiPg26eSsgk4Yv/U9
cuULEuOc/UnTj3w5VK8SvpyXMybVF6oQhSrS1slOglfFwPTlTI/NHU9xo7Wc3qHT
VifHXNphIvye5EH8zwtKX5p8qCrFW0pevJwyfPz7Hp2CTA9XYKx3SoeOh+n9F9ez
udBBggg7Vb1tb4mPKUoZ78UrtCVdFSCmesBU/RJe7cIh8daKaO5MVr3WPSx2JhM=
=yGai
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI updates from James Bottomley:
"This patch set consists of the usual driver updates (ufs, storvsc,
pm8001 hpsa). It also has removal of the user space target driver
code (everyone is using LIO now), a partial PCI MSI-X update, more
multi-queue updates, conversion to 64 bit LUNs (so we could
theoretically cope with any LUN returned by a device) and placeholder
support for the ZBC device type (Shingle drives), plus an assortment
of minor updates and bug fixes"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (143 commits)
scsi: do not issue SCSI RSOC command to Promise Vtrak E610f
vmw_pvscsi: Use pci_enable_msix_exact() instead of pci_enable_msix()
pm8001: Fix invalid return when request_irq() failed
lpfc: Remove superfluous call to pci_disable_msix()
isci: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Use pci_enable_msix_exact() instead of pci_enable_msix()
bfa: Cleanup bfad_setup_intr() function
bfa: Do not call pci_enable_msix() after it failed once
fnic: Use pci_enable_msix_exact() instead of pci_enable_msix()
scsi: use short driver name for per-driver cmd slab caches
scsi_debug: support scsi-mq, queues and locks
Drivers: add blist flags
scsi: ufs: fix endianness sparse warnings
scsi: ufs: make undeclared functions static
bnx2i: Update driver version to 2.7.10.1
pm8001: fix a memory leak in nvmd_resp
pm8001: fix update_flash
pm8001: fix a memory leak in flash_update
pm8001: Cleaning up uninitialized variables
pm8001: Fix to remove null pointer checks that could never happen
...
Pull networking updates from David Miller:
"Highlights:
1) Steady transitioning of the BPF instructure to a generic spot so
all kernel subsystems can make use of it, from Alexei Starovoitov.
2) SFC driver supports busy polling, from Alexandre Rames.
3) Take advantage of hash table in UDP multicast delivery, from David
Held.
4) Lighten locking, in particular by getting rid of the LRU lists, in
inet frag handling. From Florian Westphal.
5) Add support for various RFC6458 control messages in SCTP, from
Geir Ola Vaagland.
6) Allow to filter bridge forwarding database dumps by device, from
Jamal Hadi Salim.
7) virtio-net also now supports busy polling, from Jason Wang.
8) Some low level optimization tweaks in pktgen from Jesper Dangaard
Brouer.
9) Add support for ipv6 address generation modes, so that userland
can have some input into the process. From Jiri Pirko.
10) Consolidate common TCP connection request code in ipv4 and ipv6,
from Octavian Purdila.
11) New ARP packet logger in netfilter, from Pablo Neira Ayuso.
12) Generic resizable RCU hash table, with intial users in netlink and
nftables. From Thomas Graf.
13) Maintain a name assignment type so that userspace can see where a
network device name came from (enumerated by kernel, assigned
explicitly by userspace, etc.) From Tom Gundersen.
14) Automatic flow label generation on transmit in ipv6, from Tom
Herbert.
15) New packet timestamping facilities from Willem de Bruijn, meant to
assist in measuring latencies going into/out-of the packet
scheduler, latency from TCP data transmission to ACK, etc"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1536 commits)
cxgb4 : Disable recursive mailbox commands when enabling vi
net: reduce USB network driver config options.
tg3: Modify tg3_tso_bug() to handle multiple TX rings
amd-xgbe: Perform phy connect/disconnect at dev open/stop
amd-xgbe: Use dma_set_mask_and_coherent to set DMA mask
net: sun4i-emac: fix memory leak on bad packet
sctp: fix possible seqlock seadlock in sctp_packet_transmit()
Revert "net: phy: Set the driver when registering an MDIO bus device"
cxgb4vf: Turn off SGE RX/TX Callback Timers and interrupts in PCI shutdown routine
team: Simplify return path of team_newlink
bridge: Update outdated comment on promiscuous mode
net-timestamp: ACK timestamp for bytestreams
net-timestamp: TCP timestamping
net-timestamp: SCHED timestamp on entering packet scheduler
net-timestamp: add key to disambiguate concurrent datagrams
net-timestamp: move timestamp flags out of sk_flags
net-timestamp: extend SCM_TIMESTAMPING ancillary data struct
cxgb4i : Move stray CPL definitions to cxgb4 driver
tcp: reduce spurious retransmits due to transient SACK reneging
qlcnic: Initialize dcbnl_ops before register_netdev
...
Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf2ZIACgkQMUfUDdst+ylvQwCfQKPKcwhtq4vJ2imUzJROEZwN
ygYAnRpFpH/19X59uGSdE7DAdhbitqKg
=uPh1
-----END PGP SIGNATURE-----
Merge tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here is the big USB driver update for 3.17-rc1.
Loads of gadget driver changes in here, including some big file
movements to make things easier to manage over time. There's also the
usual xhci and uas driver updates, and a handful of other changes in
here. The changelog has the full details.
All of these have been in linux-next for a while"
* tag 'usb-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (211 commits)
USB: devio: fix issue with log flooding
uas: Log a warning when we cannot use uas because the hcd lacks streams
uas: Only complain about missing sg if all other checks succeed
xhci: Add missing checks for xhci_alloc_command failure
xhci: Rename Asrock P67 pci product-id to EJ168
xhci: Blacklist using streams on the Etron EJ168 controller
uas: Limit qdepth to 32 when connected over usb-2
uwb/whci: use correct structure type name in sizeof
usb-core bInterval quirk
USB: serial: ftdi_sio: Add support for new Xsens devices
USB: serial: ftdi_sio: Annotate the current Xsens PID assignments
usb: chipidea: debug: fix sparse non static symbol warnings
usb: ci_hdrc_imx doc: fsl,usbphy is required
usb: ci_hdrc_imx: Return -EINVAL for missing USB PHY
usb: core: allow zero packet flag for interrupt urbs
usb: lvstest: Fix sparse warnings generated by kbuild test bot
USB: core: hcd-pci: free IRQ before disabling PCI device when shutting down
phy: miphy365x: Represent each PHY channel as a DT subnode
phy: miphy365x: Provide support for the MiPHY356x Generic PHY
phy: miphy365x: Add Device Tree bindings for the MiPHY365x
...
Here's the big pull request for the staging driver tree for 3.17-rc1.
Lots of things in here, over 2000 patches, but the best part is this:
1480 files changed, 39070 insertions(+), 254659 deletions(-)
Thanks to the great work of Kristina Martšenko, 14 different staging
drivers have been removed from the tree as they were obsolete and no one
was willing to work on cleaning them up. Other than the driver
removals, loads of cleanups are in here (comedi, lustre, etc.) as well
as the usual IIO driver updates and additions.
All of this has been in the linux-next tree for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlPf1wYACgkQMUfUDdst+ykrNwCgswPkRSAPQ3C8WvLhzUYRZZ/L
AqEAoJP0Q8Fz8unXjlSMcx7pgcqUaJ8G
=mrTQ
-----END PGP SIGNATURE-----
Merge tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging driver updates from Greg KH:
"Here's the big pull request for the staging driver tree for 3.17-rc1.
Lots of things in here, over 2000 patches, but the best part is this:
1480 files changed, 39070 insertions(+), 254659 deletions(-)
Thanks to the great work of Kristina Martšenko, 14 different staging
drivers have been removed from the tree as they were obsolete and no
one was willing to work on cleaning them up. Other than the driver
removals, loads of cleanups are in here (comedi, lustre, etc.) as well
as the usual IIO driver updates and additions.
All of this has been in the linux-next tree for a while"
* tag 'staging-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (2199 commits)
staging: comedi: addi_apci_1564: remove diagnostic interrupt support code
staging: comedi: addi_apci_1564: add subdevice to check diagnostic status
staging: wlan-ng: coding style problem fix
staging: wlan-ng: fixing coding style problems
staging: comedi: ii_pci20kc: request and ioremap memory
staging: lustre: bitwise vs logical typo
staging: dgnc: Remove unneeded dgnc_trace.c and dgnc_trace.h
staging: dgnc: rephrase comment
staging: comedi: ni_tio: remove some dead code
staging: rtl8723au: Fix static symbol sparse warning
staging: rtl8723au: usb_dvobj_init(): Remove unused variable 'pdev_desc'
staging: rtl8723au: Do not duplicate kernel provided USB macros
staging: rtl8723au: Remove never set struct pwrctrl_priv.bHWPowerdown
staging: rtl8723au: Remove two never set variables
staging: rtl8723au: RSSI_test is never set
staging:r8190: coding style: Fixed checkpatch reported Error
staging:r8180: coding style: Fixed too long lines
staging:r8180: coding style: Fixed commenting style
staging: lustre: ptlrpc: lproc_ptlrpc.c - fix dereferenceing user space buffer
staging: lustre: ldlm: ldlm_resource.c - fix dereferenceing user space buffer
...
usbfs allows user space to pass down an URB which sets URB_SHORT_NOT_OK
for output URBs. That causes usbcore to log messages without limit
for a nonsensical disallowed combination. The fix is to silently drop
the attribute in usbfs.
The problem is reported to exist since 3.14
https://www.virtualbox.org/ticket/13085
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable@vger.kernel.org
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
So that an user who wants to use uas can see why he is not getting uas.
Also move the check down so that we don't warn if there are other reasons
why uas cannot work.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Don't complain about controllers without sg support if there are other
reasons why uas cannot be used anyways.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 7023 product id is the generic product id for the Etron EJ168, it is
not specific to the version found on the Asrock P67 motherboard. The same id
is e.g. also used on Gigabyte motherboards and on no-name pci-e usb-3 addon
cards.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Streams on the EJ168 do not work as they should. I've spend 2 days trying
to get them to work, but without success.
The first problem is that when ever you ring the stream-ring doorbell, the
controller starts executing trbs at the beginning of the first ring segment,
event if it ended somewhere else previously. This can be worked around by
allowing enqueing only one td (not a problem with how streams are typically
used) and then resetting our copies of the enqueueing en dequeueing pointers
on a td completion to match what the controller seems to be doing.
This way things seem to start working with uas and instead of being able
to complete only the very first scsi command, the scsi core can probe the disk.
But then things break later on when td-s get enqueued with more then one
trb. The controller does seem to increase its dequeue pointer while executing
a stream-ring (data transfer events I inserted for debugging do trigger).
However execution seems to stop at the final normal trb of a multi trb td,
even if there is a data transfer event inserted after the final trb.
The first problem alone is a serious deviation from the spec, and esp.
dealing with cancellation would have been very tricky if not outright
impossible, but the second problem simply is a deal breaker altogether,
so this patch simply disables streams.
Note this will cause the usb-storage + uas driver pair to automatically switch
to using usb-storage instead of uas on these devices, essentially reverting
to the 3.14 and earlier behavior when uas was marked CONFIG_BROKEN.
https://bugzilla.redhat.com/show_bug.cgi?id=1121288https://bugzilla.kernel.org/show_bug.cgi?id=80101
Cc: stable@vger.kernel.org # 3.15
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some jmicron uas chipsets act up (they disconnect from the bus) when sending
more then 32 commands to them at once.
Rather then building an ever growing list with usb-id based quirks for
devices using this chipset, simply reduce the qdepth to 32 when connected
over usb-2. 32 should be plenty to keep things close to maximum
possible throughput on usb-2.
Cc: stable@vger.kernel.org
Tested-and-reported-by: Laszlo T. <tlacix@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a usb quirk to support devices with interupt endpoints
and bInterval values expressed as microframes. The quirk causes the
parse endpoint function to modify the reported bInterval to a standards
conforming value.
There is currently code in the endpoint parser that checks for
bIntervals that are outside of the valid range (1-16 for USB 2+ high
speed and super speed interupt endpoints). In this case, the code assumes
the bInterval is being reported in 1ms frames. As well, the correction
is only applied if the original bInterval value is out of the 1-16 range.
With this quirk applied to the device, the bInterval will be
accurately adjusted from microframes to an exponent.
Signed-off-by: James P Michels III <james.p.michels@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for new Xsens devices, using Xsens' own Vendor ID.
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The converters are used in specific products. It can be useful to know
which they are exactly.
Signed-off-by: Patrick Riphagen <patrick.riphagen@xsens.com>
Signed-off-by: Frans Klaver <frans.klaver@xsens.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver hasn't been fully cleaned up and it doesn't look like anyone
is working on it anymore (including the original author). So remove the
driver and all references to it. If someone wants to finish cleaning
the driver up and moving it out of staging, this commit can be reverted.
Signed-off-by: Kristina Martšenko <kristina.martsenko@gmail.com>
Cc: Cho, Yu-Chen <acho@novell.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following sparse warnings:
drivers/usb/chipidea/debug.c:211:5: warning:
symbol 'ci_otg_show' was not declared. Should it be static?
drivers/usb/chipidea/debug.c:334:5: warning:
symbol 'ci_registers_show' was not declared. Should it be static?
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-ENODEV is interpreted by the generic driver probing function as a
non-matching driver. This leads to a missing probe failure message.
Also a missing USB PHY is more of an invalid configuration of the usb
driver because it is necessary.
This patch returns -EINVAL if devm_usb_get_phy_by_phandle() returned -ENODEV.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Section 4.4.7.2 "Interrupt Transfer Bandwidth Requirements" of the USB3.0 spec
says:
A zero-length data payload is a valid transfer and may be useful for
some implementations.
So, extend the logic of allowing URB_ZERO_PACKET to interrupt urbs too.
Otherwise, the kernel throws warning of BOGUS transfer flags.
Signed-off-by: Amit Virdi <amit.virdi@st.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Conflicts:
drivers/infiniband/hw/cxgb4/device.c
The cxgb4 conflict was simply overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=aJY4
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v3.17 merge window
Surprisingly enough, while a big set of patches, the majority is
composed of cleanups (using devm_*, fixing sparse errors, moving
code around, adding const, etc).
The highlights are addition of new support for PLX USB338x devices,
and support for USB 2.0-only configurations of the DWC3 IP core.
Signed-of-by: Felipe Balbi <balbi@ti.com>
This patch adds an extra check to ohci-hcd's I/O watchdog routine. If
the controller stops updating the frame counter, we will assume it is
dead. But there has to be an exception: Some controllers stop the
frame counter when no ports are connected. Check to make sure there
is at least one active port before deciding the controller is dead.
(This test may appear racy, but it isn't. Enabling a newly connected
port takes several milliseconds, during which time the frame counter
must advance.)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Tested-by: Dennis New <dennisn@dennisn.linuxd.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some OHCI controllers have a bug: They fail to add completed TDs to
the done queue. Examining this queue is the only method ohci-hcd has
for telling when a transfer is complete; failure to add a TD can
result in an URB that never completes and cannot be unlinked.
This patch adds a watchdog routine to ohci-hcd. The routine
periodically scans the active ED and TD lists, looking for TDs which
are finished but not on the done queue. When one is found, and it is
certain that the controller hardware will never add the TD to the done
queue, the watchdog routine manually puts the TD on the done list so
that it can be handled normally.
The watchdog routine also checks for a condition indicating the
controller has died. If the done queue is non-empty but the
HccaDoneHead pointer hasn't been updated for a few hundred
milliseconds, we assume the controller will never update it and
therefore is dead.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
URBs for a particular endpoint should complete sequentially. That is,
we shouldn't call the completion handler for one URB until the handler
for the previous URB has returned.
When the OHCI watchdog routine is added, there will be two paths for
completing URBs: interrupt handler and watchdog routine. Their
activities have to be synchronized so that completions don't occur in
multiple threads concurrently.
For that purpose, this patch creates an ohci_work() routine which will
be responsible for calling process_done_list() and finish_unlinks(),
the two routines that detect when an URB is complete. Everything will
funnel through ohci_work(), and it will be careful not to run in more
than one thread at a time.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch changes the way ohci-hcd handles the TD done list. In
addition to relying on the TD pointers stored by the controller
hardware, we need to handle TDs that the hardware has forgotten about.
This means the list has to exist even while the dl_done_list() routine
isn't running. That function essentially gets split in two:
update_done_list() reads the TD pointers stored by the hardware and
adds the TDs to the done list, and process_done_list() scans through
the list to handle URB completions. When we detect a TD that the
hardware forgot about, we will be able to add it to the done list
manually and then process it normally.
Since the list is really a queue, and because there can be a lot of
TDs, keep the existing singly linked implementation. To insure that
URBs are given back in order of submission, whenever a TD is added to
the done list, all the preceding TDs for the same endpoint must be
added as well (going back to the first one that isn't already on the
done list).
The done list manipulations must all be protected by the private
lock. The scope of the lock is expanded in preparation for the
watchdog routine to be added in a later patch.
We have to be more careful about giving back unlinked URBs. Since TDs
may be added to the done list by the watchdog routine and not in
response to a controller interrupt, we have to check explicitly to
make sure all the URB's TDs that were added to the done list have been
processed before giving back the URB.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When an URB is unlinked from a dead controller, ohci-hcd gives back
the URB with no regard for cleaning up the internal data structures.
This won't play nicely with the upcoming changes to the TD done
list.
Therefore make ohci_urb_dequeue() call finish_unlinks(), which uses
td_done() to do a proper cleanup, rather than calling finish_urb()
directly. Also, remove the checks that urb_priv is non-NULL; the
driver guarantees that urb_priv will never be NULL for a valid URB.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch reverts the important parts of commit 89a0fd18a9 (USB:
OHCI handles more ZFMicro quirks), namely, the parts related to
handling orphan TDs for interrupt endpoints. A later patch in this
series will introduce a more general mechanism that applies to all
endpoint types and all controllers.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Problem Summary: Problem has been observed generally with PM states
where VBUS goes off during suspend. There are some SS USB devices which
take longer time for link training compared to many others. Such
devices fail to reconnect with same old address which was associated
with it before suspend.
When system resumes, at some point of time (dpm_run_callback->
usb_dev_resume->usb_resume->usb_resume_both->usb_resume_device->
usb_port_resume) SW reads hub status. If device is present,
then it finishes port resume and re-enumerates device with same
address. If device is not present then, SW thinks that device was
removed during suspend and therefore does logical disconnection
and removes all the resource allocated for this device.
Now, if I put sufficient delay just before root hub status read in
usb_resume_device then, SW sees always that device is present. In normal
course(without any delay) SW sees that no device is present and then SW
removes all resource associated with the device at this port. In the
latter case, after sometime, device says that hey I am here, now host
enumerates it, but with new address.
Problem had been reproduced when I connect verbatim USB3.0 hard disc
with my STiH407 XHCI host running with 3.10 kernel.
I see that similar problem has been reported here.
https://bugzilla.kernel.org/show_bug.cgi?id=53211
Reading above it seems that bug was not in 3.6.6 and was present in 3.8
and again it was not present for some in 3.12.6, while it was present
for few others. I tested with 3.13-FC19 running at i686 desktop, problem
was still there. However, I was failed to reproduce it with 3.16-RC4
running at same i686 machine. I would say it is just a random
observation. Problem for few devices is always there, as I am unable to
find a proper fix for the issue.
So, now question is what should be the amount of delay so that host is
always able to recognize suspended device after resume.
XHCI specs 4.19.4 says that when Link training is successful, port sets
CSC bit to 1. So if SW reads port status before successful link
training, then it will not find device to be present. USB Analyzer log
with such buggy devices show that in some cases device switch on the
RX termination after long delay of host enabling the VBUS. In few other
cases it has been seen that device fails to negotiate link training in
first attempt. It has been reported till now that few devices take as
long as 2000 ms to train the link after host enabling its VBUS and
RX termination. This patch implements a 2000 ms timeout for CSC bit to set
ie for link training. If in a case link trains before timeout, loop will
exit earlier.
This patch implements above delay, but only for SS device and when
persist is enabled.
So, for the good device overhead is almost none. While for the bad
devices penalty could be the time which it take for link training.
But, If a device was connected before suspend, and was removed
while system was asleep, then the penalty would be the timeout ie
2000 ms.
Results:
Verbatim USB SS hard disk connected with STiH407 USB host running 3.10
Kernel resumes in 461 msecs without this patch, but hard disk is
assigned a new device address. Same system resumes in 790 msecs with
this patch, but with old device address.
Cc: <stable@vger.kernel.org>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I am removing two fix mes in this file as after dicussing then it seems
there is no reason to check against Null for usb_device as it can never
be NULL and this is check is therefore not needed.
Signed-off-by: Nicholas Krause <xerofoify@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some laptops have an internal port for a BT device which picks
up noise when the kill switch is used, but not enough to trigger
printk_rlimit(). So we shouldn't log consecutive faults of this kind.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When using USB 3.0 pen drive with the [AMD] FCH USB XHCI Controller
[1022:7814], the second hotplugging will experience the USB 3.0 pen
drive is recognized as high-speed device. After bisecting the kernel,
I found the commit number 41e7e056cd
(USB: Allow USB 3.0 ports to be disabled.) causes the bug. After doing
some experiments, the bug can be fixed by avoiding executing the function
hub_usb3_port_disable(). Because the port status with [AMD] FCH USB
XHCI Controlleris [1022:7814] is already in RxDetect
(I tried printing out the port status before setting to Disabled state),
it's reasonable to check the port status before really executing
hub_usb3_port_disable().
Fixes: 41e7e056cd (USB: Allow USB 3.0 ports to be disabled.)
Signed-off-by: Gavin Guo <gavin.guo@canonical.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This `usb_reset_device` command has been around since the driver was
originally reverse engineered. It doesn't cause much issue on single
interface CP210x devices, but on the CP2105 and CP2108 with 2 and 4
interfaces respectively it will cause instability on enumeration and
delays enumeration noticably. There should be no reason to reset a device
at startup, per the CP210x AN571 spec.
Signed-off-by: Preston Fick <preston.fick@silabs.com>
Cc: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OTG3 and EH Compliance Plan 1.0 talks about Super Speed OTG Verification
system (SS-OVS) which consists of an excersizer and analyzer.
USB Compliance Suite from Lecroy or Ellisys can act as such SS-OVS for
Link Layer Validation (LVS).
Some modifications are needed for an embedded Linux USB host to pass all
these tests. Most of these tests require just Link to be in U0. They do
not work with default Linux USB stack since, default stack does port
reset and then starts sending setup packet, which is not expected by
Link Layer Validation (LVS) device of Lecroy Compliance Suit. Then,
There are many Link Layer Tests which need host to generate specific
traffic.
This patch supports specific traffic generation cases. As of now all the
host Lecroy Link Layer-USBIF tests (except TD7.26) passes
with this patch for single run using Lecroy USB Compliance Suite
Version 1.98 Build 239 and Lecroy USB Protocol Analyzer version 4.80
Build 1603. Therefore patch seems to be a good candidate for inclusion.
Further modification can be done on top of it.
lvstest driver will not bind to any device by default. It can bind
manually to a super speed USB host controller root hub. Therefore, regular
hub driver must be unbound before this driver is bound. For example, if
2-0:1.0 is the xhci root hub, then execute following to unbind hub driver.
echo 2-0:1.0 > /sys/bus/usb/drivers/hub/unbind
Then write Linux Foundation's vendor ID which is used by root hubs and
SS root hub's device ID into new_id file. Writing IDs into new_id file
will also bind the lvs driver with any available SS root hub interfaces.
echo "1D6B 3" > /sys/bus/usb/drivers/lvs/new_id
Now connect LVS device with root hub port.
Test case specific traffic can be generated as follows whenever needed:
1. To issue "Get Device descriptor" command for TD.7.06:
echo > /sys/bus/usb/devices/2-0\:1.0/get_dev_desc
2. To set U1 timeout to 127 for TD.7.18
echo 127 > /sys/bus/usb/devices/2-0\:1.0/u1_timeout
3. To set U2 timeout to 0 for TD.7.18
echo 0 > /sys/bus/usb/devices/2-0\:1.0/u2_timeout
4. To issue "Hot Reset" for TD.7.29
echo > /sys/bus/usb/devices/2-0\:1.0/hot_reset
5. To issue "U3 Entry" for TD.7.35
echo > /sys/bus/usb/devices/2-0\:1.0/u3_entry
6. To issue "U3 Exit" for TD.7.36
echo > /sys/bus/usb/devices/2-0\:1.0/u3_exit
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usb_alloc_dev is used by lvstest driver now which can be built as
module. Therefore export usb_alloc_dev symbol.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes a bug in ohci-hcd. When an URB is unlinked, the
corresponding Endpoint Descriptor is added to the ed_rm_list and taken
off the hardware schedule. Once the ED is no longer visible to the
hardware, finish_unlinks() handles the URBs that were unlinked or have
completed. If any URBs remain attached to the ED, the ED is added
back to the hardware schedule -- but only if the controller is
running.
This fails when a controller dies. A non-empty ED does not get added
back to the hardware schedule and does not remain on the ed_rm_list;
ohci-hcd loses track of it. The remaining URBs cannot be unlinked,
which causes the USB stack to hang.
The patch changes finish_unlinks() so that non-empty EDs remain on
the ed_rm_list if the controller isn't running. This requires moving
some of the existing code around, to avoid modifying the ED's hardware
fields more than once.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The debug routine fill_async_buffer() in ohci-hcd is buggy: It never
produces any output because it forgets to initialize the output buffer
size. Also, the debug routine ohci_dump() has an unused argument.
This patch adds the correct initialization and removes the unused
argument.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently nobody ever remembered to add Scatter-Gather support to
ohci-hcd. This patch adds it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a host controller dies, we don't need to wait for a driver to
time out. We can shut down its URBs immediately. Without this
change, we can end up waiting 30 seconds for a mass-storage transfer
to time out.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are 2 methods for ZLP (zero-length packet) generation:
1) In software
2) Automatic generation by device controller
1) is implemented in UDC driver and it attaches ZLP to IN packet if
descriptor->size < wLength
2) can be enabled/disabled by setting ZLT bit in the QH
When gadget ffs is connected to ubuntu host, the host sends
get descriptor request and wLength in setup packet is 255 while the
size of descriptor which will be sent by gadget in IN packet is
64 byte. So the composite driver sets req->zero = 1.
In UDC driver following code will be executed then
if (hwreq->req.zero && hwreq->req.length
&& (hwreq->req.length % hwep->ep.maxpacket == 0))
add_td_to_list(hwep, hwreq, 0);
Case-A:
So in case of ubuntu host, UDC driver will attach a ZLP to the IN packet.
ubuntu host will request 255 byte in IN request, gadget will send 64 byte
with ZLP and host will come to know that there is no more data.
But hold on, by default ZLT=0 for endpoint 0 so hardware also tries to
automatically generate the ZLP which blocks enumeration for ~6 seconds due
to endpoint 0 STALL, NAKs are sent to host for any requests (OUT/PING)
Case-B:
In case when gadget ffs is connected to Apple device, Apple device sends
setup packet with wLength=64. So descriptor->size = 64 and wLength=64
therefore req->zero = 0 and UDC driver will not attach any ZLP to the
IN packet. Apple device requests 64 bytes, gets 64 bytes and doesn't
further request for IN data. But ZLT=0 by default for endpoint 0 so
hardware tries to automatically generate the ZLP which blocks enumeration
for ~6 seconds due to endpoint 0 STALL, NAKs are sent to host for any
requests (OUT/PING)
According to USB2.0 specs:
8.5.3.2 Variable-length Data Stage
A control pipe may have a variable-length data phase in which the
host requests more data than is contained in the specified data
structure. When all of the data structure is returned to the host,
the function should indicate that the Data stage is ended by
returning a packet that is shorter than the MaxPacketSize for the
pipe. If the data structure is an exact multiple of wMaxPacketSize
for the pipe, the function will return a zero-length packet to indicate
the end of the Data stage.
In Case-A mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint 0 OR if software
ZLP generation is not disabled but we set ZLT=1 for endpoint 0 then
enumeration doesn't block for 6 seconds.
In Case-B mentioned above:
If we disable software ZLP generation & ZLT=0 for endpoint then enumeration
still blocks due to ZLP automatically generated by hardware and host not needing
it. But if we keep software ZLP generation enabled but we set ZLT=1 for
endpoint 0 then enumeration doesn't block for 6 seconds.
So the proper solution for this issue seems to disable automatic ZLP generation
by hardware (i.e by setting ZLT=1 for endpoint 0) and let software (UDC driver)
handle the ZLP generation based on req->zero field.
Cc: stable@vger.kernel.org
Signed-off-by: Abbas Raza <Abbas_Raza@mentor.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The SCSI standard defines 64-bit values for LUNs, and large arrays
employing large or hierarchical LUN numbers become more and more
common.
So update the linux SCSI stack to use 64-bit LUN numbers.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Christoph Hellwig <hch@infradead.org>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Obsolete; either use 'max_lun' if the host supports only a
limited number of LUNs or BLIST_NOLUN if the target has
problems addressing more than one LUN.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
f->os_desc_table[0].if_id is zero by default. If the actual id happens
to be different then no Feature Descriptors will be returned to the host
for this interface, so assign if_id as soon as it is known.
Cc: <stable@vger.kernel.org> # v3.16
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The pcm playback and capture sample size format was fixed
SNDRV_PCM_FMTBIT_S16_LE.
This patch respects also 16, 24 and 32 bit p_ssize and c_ssize values.
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Sebastian Reimers <sebastian.reimers@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional changes, just fixing one easy to spot
sparse error.
While fixing that sparse error, I had to add two
includes to a header to avoid a build error.
Signed-off-by: Felipe Balbi <balbi@ti.com>
The drivers/usb/gadget directory contains many files.
Files which are related can be distributed into separate directories.
This patch moves the USB functions implementations into a separate directory.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The drivers/usb/gadget directory contains many files.
Files which are related can be distributed into separate directories.
This patch moves the UDC drivers into a separate directory.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The drivers/usb/gadget directory contains many files.
Files which are related can be distributed into separate directories.
This patch moves the legacy gadgets (i.e. those not using configfs)
into a separate directory.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Here are some minor fixes and clean-ups to the ftdi_sio, mos7840 and kl5kusb105
drivers for v3.17-rc1.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=tUqf
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-3.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for v3.17-rc1
Here are some minor fixes and clean-ups to the ftdi_sio, mos7840 and kl5kusb105
drivers for v3.17-rc1.
Signed-off-by: Johan Hovold <johan@kernel.org>
In preparation for DT conversion to reduce reliance on platform device
callbacks.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch try to dequeue the cdev->req to guarantee the request is not queued
before free it.
Signed-off-by: Li Jun <b47624@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add sw_babble_control() logic to differentiate between transient
babble and real babble condition. Also add the SW babble control
register definitions.
Babble control register logic is implemented in the latest
revision of AM335x.
Find whether we are running on newer silicon. The babble control
register reads 0x4 by default in newer silicon as opposed to 0
in old versions of AM335x. Based on this enable the sw babble
control logic.
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Currently musb_platform_reset() is only used by dsps.
In case of BABBLE interrupt for other platforms the musb_platform_reset()
is a NOP. In such situations no need to re-initialize the endpoints.
Also in the latest silicon revision of AM335x, we do have a babble recovery
mechanism without resetting the IP block. In preperation to add that support
its better to have a rest_done return for musb_platform_reset().
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During babble condition both first disconnect of devices are
initiated. Make sure MUSB controller is reset and re-initialized
after all disconnects.
To acheive this schedule a delayed work for babble recovery.
While at that convert udelay to usleep_range.
Refer Documentation/timers/timers-howto.txt
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
BABBLE and RESET share the same interrupt. The interrupt
is considered to be RESET if MUSB is in peripheral mode and
as a BABBLE if MUSB is in HOST mode.
Handle babble condition iff MUSB is in HOST mode.
Signed-off-by: George Cherian <george.cherian@ti.com>
Tested-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move the extcon related code to its own function.
Improve code readability, decrease the dwc3_probe() size.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move find and set the utmi mode to its own separate function.
Improve code readability, decrease the dwc3_probe() size.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Move map offset to its own separate function.
Improve code readability, decrease the dwc3_probe() size.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the x_major calculation logic from the wrapper revision register
to differentiate between OMAP5 and AM437x. This was done to find the
register offsets of wrapper register. Now that We do it using dt
compatible, remove the whole logic.
Signed-off-by: George Cherian <george.cherian@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The usb device will autoresume from choose_wakeup() if it is
autosuspended with the wrong wakeup setting, but below errors occur
because usb3503 misc driver will switch to standby mode when suspended.
As add USB_QUIRK_RESET_RESUME, it can stop setting wrong wakeup from
autosuspend_check().
[ 7.734717] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 7.854658] usb 1-3: device descriptor read/64, error -71
[ 8.079657] usb 1-3: device descriptor read/64, error -71
[ 8.294664] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 8.414658] usb 1-3: device descriptor read/64, error -71
[ 8.639657] usb 1-3: device descriptor read/64, error -71
[ 8.854667] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 9.264598] usb 1-3: device not accepting address 3, error -71
[ 9.374655] usb 1-3: reset high-speed USB device number 3 using exynos-ehci
[ 9.784601] usb 1-3: device not accepting address 3, error -71
[ 9.784838] usb usb1-port3: device 1-3 not suspended yet
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb3503 needs to switch to standby mode while suspending and should
switch to hub mode when resumed. Also we can control clock on PM
function.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a problem with dropped packets over 16k CDC-NCM
when the connection is being heavily used.
The issue was that the extracted frames cloned from the
received frame were consuming more memory than necessary
resulting in the truesize being ~32KB instead of ~2KB, this
meant there was a high chance of reaching the sk_rcvbuf
limit.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This adds multi-frame support to the NCM NTB's for
the gadget driver. This allows multiple network
packets to be put inside a single USB NTB with a
maximum size of 16kB.
It has a time out of 300ms to ensure that smaller
number of packets still maintain a normal latency.
Also the .fp_index and .next_fp_index have been
changed to .ndp_index and .next_ndp_index to
match the latest CDC-NCM specification and
help with maintenance.
Results transmitting from gadget to host.
Before the change:
TCP_STREAM Throughput (10^6bits/sec): 22.72
UDP_STREAM Throughput (10^6bits/sec): 25.94
Latency:
netperf -H 192.168.1.101 -v2 -l 50 -t TCP_RR -- -r 16384,16384
Trans. RoundTrip Throughput
Rate Latency 10^6bits/s
per sec usec/Tran Outbound
100.83 9918.116 13.215
After the change:
TCP_STREAM Throughput (10^6bits/sec): 124.26
UDP_STREAM Throughput (10^6bits/sec): 227.48
Latency:
netperf -H 192.168.1.101 -v2 -l 50 -t TCP_RR -- -r 16384,16384
Trans. RoundTrip Throughput
Rate Latency 10^6bits/s
per sec usec/Tran Outbound
156.80 6377.730 20.552
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The NDP was ignoring the wNextNdpIndex in the NDP which
means that NTBs containing multiple NDPs would have missed
frames.
Signed-off-by: Jim Baxter <jim_baxter@mentor.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Even if the skb is cloned, we still need a ZLP or USB will stall.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Acked-by: Brad Mouring <brad.mouring@ni.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove 'start_new' variable from dwc3_endpoint_transfer_complete(),
since this variable has not been used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use SIMPLE_DEV_PM_OPS macro and remove DEV_PM_OPS macro, in order
to make the code simpler.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use the module_usb_composite_driver() macro where applicable to
eliminate the module_init/module_exit boilerplate in USB gadget composite
drivers.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for OS descriptors. The new format of descriptors is used,
because the "flags" field is required for extensions. os_count gives
the number of OSDesc[] elements.
The format of descriptors is given in include/uapi/linux/usb/functionfs.h.
For extended properties descriptor the usb_ext_prop_desc structure covers
only a part of a descriptor, because the wPropertyNameLength is unknown
up front.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Provide helper functions to get pointers to particular locations within
a buffer holding an extended properties descriptor.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ffs_do_desc() handles one descriptor, while ffs_do_descs() handles a number
of descriptors. The tho names are so similar that it causes confusion.
Rename to reflect their purpose better.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
It is no longer needed and keeping it will break 64-bit ARM builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Following the name change of the NOP transceiver driver in commit
4525bee (usb: phy: rename usb_nop_xceiv to usb_phy_generic), the
transceiver driver was no longer operable under its old name.
Register the transceiver driver before calling usb_get_phy() to make
sure we are noticed by an error message if it is not available.
Signed-off-by: Apelete Seketeli <apelete@seketeli.net>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Commit e56e69cc0f ("usb: gadget: net2280: Use pr_* function")
includes a editing mistake on one of the #ifdef.
This patch fixes it.
Reported-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
commit c63d2225e7 ("usb: gadget: pxa25x_udc: use devm_ functions")
introduced the use of devm_gpio_request in this driver, but did not
correctly include the header file declaring this function, which
causes a build failure.
This changes pxa25x_udc to include linux/gpio.h instead of asm/gpio.h
to fix this.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Himangi Saraogi <himangi774@gmail.com>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Cc: Felipe Balbi <balbi@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that the renesas_usbhs driver in gadget mode
cannot work correctly even if I disabled DMAC of the driver when I used
the g_zero driver and the testusb tool.
When a usb cable is re-connected, the renesas_usbhs driver calls the
usbhsp_flags_init() (via usbhs_hotplug() --> usbhs_mod_call(start) -->
usbhsg_try_start() --> usbhs_pipe_init()). However, the driver doesn't
call the usbhsp_flags_init() when usbhsg_ep_disable() is called.
So, if a gadget driver calls usb_ep_enable() and usb_ep_disable() again
and again, the renesas_usbhs driver will output the following log:
renesas_usbhs renesas_usbhs: can't get pipe (BULK)
renesas_usbhs renesas_usbhs: wrong recip request
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes an issue that the driver cannot push a new data when
a pipe is re-enabled after the pipe is queued.
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch intoduces the use of devm_ioremap_resource instead of
request_mem_region and ioremap_nocache and removes the calls to free the
allocated memory. Some labels are removes and a new label failed
introduced to make it less specific to the context. The call to a
platform get resource with IORESOURCE_IO is removed as it allocates
memory that is not needed.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch replaces the memory allocation using request_mem_region and
the ioremap by a single call to managed interface devm_ioremap_reource.
The corresponding calls to release_mem_region and iounmap in the probe
and release functions are now unnecessary and are removed. Also a label
is done away with and linux/device.h is added to make sure the devm_*()
outine declarations are unambiguously available.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds PID 0x0003 to the VID 0x128d (Testo). At least the
Testo 435-4 uses this, likely other gear as well.
Signed-off-by: Bert Vermeulen <bert@biot.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tegra_usb_phy_close() is supposed to undo the effects of
tegra_usb_phy_init(). It is also currently added as the USB PHY shutdown
callback, which is wrong, since tegra_usb_phy_init() is only called
during probing wheras the shutdown callback can get called multiple
times. This then leads to warnings about unbalanced regulator_disable if
the EHCI driver is unbound and bound again at runtime.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Tegra USB complex has a particularly annoying misdesign: some of the
UTMI pad configuration registers are global for all the 3 USB controllers
on the chip, but those registers are located in the first controller's
register space and will be cleared when the reset to the first
controller is asserted. Currently, this means that if the 1st controller
were to finish probing after the 2nd or 3rd controller, USB would not
work at all.
Fix this situation by always resetting the 1st controller before doing
any other setup to any of the controllers, and then never ever reset the
first controller again. As the UTMI registers are related to the PHY,
the PHY driver should probably reset the Tegra controllers instead,
but since old device trees only have reset phandles in the EHCI nodes,
do it here, which means a bit of device tree groveling. Those old DTs
also won't get the reset fix from this commit, so we'll dev_warn() them,
but the driver will still keep probing successfully.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The various devm_ functions allocate memory that is released when a
driver detaches. This patch uses devm_ioremap_resource for data
that is allocated in the probe function of a platform device and
is only freed in the remove function. The corresponding free functions
are removed and two labels are done away with. Also, linux/device.h
is added to make sure the devm_*() routine declarations are
unambiguously available.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Andreas Larsson <andreas@gaisler.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The tegra_ehci_hcd structure is located in the private space allocated
by the core USB code so it must not be accessed after the HCD is
freed.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The EHCI packet buffer in/out threshold is programmable for Intel Quark X1000
USB host controller, and the default value is 0x20 dwords. The in/out threshold
can be programmed to 0x80 dwords (512 Bytes) to maximize the perfomrance,
but only when isochronous/interrupt transactions are not initiated by the USB
host controller. This patch is to reconfigure the packet buffer in/out
threshold as maximal as possible to maximize the performance, and 0x7F dwords
(508 Bytes) should be used because the USB host controller initiates
isochronous/interrupt transactions.
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@intel.com>
Signed-off-by: Alvin (Weike) Chen <alvin.chen@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Jingoo Han <jg1.han@samsung.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OHCI HCCA memory region is allocated from atomic DMA pool one time
during usb_add_hcd() and deallocated by usb_remove_hcd().
Do non-atomic allocation of OHCI HCCA and free some space in
coherent atomic DMA pool.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
uhci_start() is executed one time during usb_add_hcd() call and by
default UHCI frame list is allocated from atomic DMA pool.
Do non-atomic allocation of uhci->frame and free some space in
coherent atomic DMA pool.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ehci_mem_init() is executed one time during ehci_init() and by default
all memory allocations but ehci->periodic are done not atomically,
GFP_KERNEL is passed as flags parameter.
Do similar allocation for ehci->periodic and free some space in
coherent atomic DMA pool by default.
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes checkpatch warning:
"WARNING: debugfs_remove(NULL) is safe this check is probably not required"
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make of_device_id array const, because all OF functions handle
it as const.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the use of devm_ioremap_resource instead of
request_mem_region and ioremap. The error handling on
platform_get_resource and the error message for ioremap are removed. The
function devm_kzalloc replaces memory allocation by unmanaged kzalloc. The
function calls to free the allocated memory in the probe and remove
functions are done away with. Some labels are removed and a label error
is added to make is less specific to the context. The debug message is
removed as devm_ioremap generates debug messages of its own.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is no longer needed and keeping it will break 64-bit ARM builds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As far as kzalloc() is called with spinlock held,
we have to pass GFP_ATOMIC regardless of mem_flags argument.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: David Mosberger <davidm@egauge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The third argument of devm_of_phy_get expects a pointer.
Hence use NULL instead of 0. Fixes the following warning:
drivers/usb/host/ehci-exynos.c:91:51: warning: Using plain integer as NULL pointer
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The third argument of devm_of_phy_get expects a pointer.
Hence use NULL instead of 0.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Jingoo Han <jg1.han@samsung.com>
Reviewed-by: Vivek Gautam <gautam.vivek@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a risk that the variable will be used without being initialized.
This was largely found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The file and folder movements resulted in the incorrect reference.
So for better code maintainability, let's remove it.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix checkpatch errors as belows.
ERROR: open brace '{' following function declarations go on the next line
ERROR: space required before the open parenthesis '('
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Paul Zimmerman <paulz@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The R-Car H2 and M2 SoCs come with an xHCI controller that requires
some specific initializations related to the firmware downloading and
some specific registers. This patch adds the support for this special
configuration as an xHCI quirk executed during probe and start.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: "mathias.nyman@intel.com" <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces the use of managed interface devm_ioremap_resource
for ioremap_nocache and request_mem_region and removes the corresponding
free functions in the probe and remove functions.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
grep must work, not matter the line length.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch remove the function klsi_105_tiocmset which was only
returning -EINVAL. It also removes the function prototype and
the .tiocmset entry in the struct usb_serial_driver.
Verified by compilation only.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Resuming a powered down port sometimes results in the port state being
stuck in the training sequence.
hub 3-0:1.0: debounce: port 1: total 2000ms stable 0ms status 0x2e0
port1: can't get reconnection after setting port power on, status -110
hub 3-0:1.0: port 1 status 0000.02e0 after resume, -19
usb 3-1: can't resume, status -19
hub 3-0:1.0: logical disconnect on port 1
In the case above we wait for the port re-connect timeout of 2 seconds
and observe that the port status is USB_SS_PORT_LS_POLLING (although it
is likely toggling between this state and USB_SS_PORT_LS_RX_DETECT).
This is indicative of a case where the device is failing to progress the
link training state machine.
It is resolved by issuing a warm reset to get the hub and device link
state machines back in sync.
hub 3-0:1.0: debounce: port 1: total 2000ms stable 0ms status 0x2e0
usb usb3: port1 usb_port_runtime_resume requires warm reset
hub 3-0:1.0: port 1 not warm reset yet, waiting 50ms
usb 3-1: reset SuperSpeed USB device number 2 using xhci_hcd
After a reconnect timeout when we expect the device to be present, force
a warm reset of the device. Note that we can not simply look at the
link status to determine if a warm reset is required as any of the
training states USB_SS_PORT_LS_POLLING, USB_SS_PORT_LS_RX_DETECT, or
USB_SS_PORT_LS_COMP_MOD are valid states that do not indicate the need
for warm reset by themselves.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: Vincent Palatin <vpalatin@chromium.org>
Cc: Lan Tianyu <tianyu.lan@intel.com>
Cc: Ksenia Ragiadakou <burzalodowa@gmail.com>
Cc: Vivek Gautam <gautam.vivek@samsung.com>
Cc: Douglas Anderson <dianders@chromium.org>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Sunil Joshi <joshi@samsung.com>
Cc: Hans de Goede <hdegoede@redhat.com>
Acked-by: Julius Werner <jwerner@chromium.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When a USB device is disconnected, usb_unbind_interface is called, which
tries to enable and disable LPM. usb_enable_lpm also try to send a
control command SET SEL to the device.
Since device is already disconnected, therefore it does not make sense
to execute usb_(en/dis)able_lpm.
This patch returns from usb_(en/dis)able_lpm, if device was not in
default state atleast.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Aymen Bouattay <aymen.bouattay@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All dwc3 based xhci host controller supports USB3.0 LPM functionality.
Therefore enable it in platform data for all dwc3 based xhci device if
DWC3_HOST_USB3_LPM_ENABLE is selected in Kconfig.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To use auto U0-U1/U2 transition by xhci platform device add
(en/dis)able_usb3_lpm_timeout function to the xhci_plat_xhci_driver struct.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Aymen Bouattay <aymen.bouattay@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As best case, a host controller should support U0 to U1 switching for
the devices connected below any tier of hub level supported by usb
specification. Therefore xhci_check_tier_policy should always return
success as default implementation.
A host should be able to issue LGO_Ux after the timeout calculated as
per definition of system exit latency defined in C.1.5.2. Therefore
xhci_calculate_ux_timeout returns ux_params.sel as the default
implementation.
Use default calculation in absence of any vendor specific limitations.
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Aymen Bouattay <aymen.bouattay@st.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'err' is uninitialized, rather print the error code directly.
This also fixes following warning.
drivers/usb/misc/usb3503.c: In function ‘usb3503_probe’:
drivers/usb/misc/usb3503.c:195:11: warning: ‘err’ may be used uninitialized
in this function [-Wmaybe-uninitialized]
dev_err(dev, "unable to request refclk (%d)\n", err);
Signed-off-by: Tushar Behera <tushar.b@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch remove the function klsi_105_tiocmset which was only
returning -EINVAL. It also removes the function prototype and
the .tiocmset entry in the struct usb_serial_driver.
Verified by compilation only.
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add ID of the Telewell 4G v2 hardware to option driver to get legacy
serial interface working
Signed-off-by: Bernd Wachter <bernd.wachter@jolla.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Corsair USB Dongles are shipped with Corsair AXi series PSUs.
These are cp210x serial usb devices, so make driver detect these.
I have a program, that can get information from these PSUs.
Tested with 2 different dongles shipped with Corsair AX860i and
AX1200i units.
Signed-off-by: Andras Kovacs <andras@sth.sze.hu>
Cc: <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove redundant mtxorb quirk used to fix up incorrect wMaxPacketSize,
which was added before 895f28badc ("USB: ftdi_sio: fix hi-speed device
packet size calculation") which does the same thing for all devices.
Signed-off-by: Johan Hovold <johan@kernel.org>
Promote max-packet-size-override message to warning level and use the
port device for logging, while using actual endpoint numbers in the
message itself.
Signed-off-by: Johan Hovold <johan@kernel.org>
There's no need to print the number of endpoints per interface or
endpoint wMaxPacketSize during port probe. This information is readily
available using lsusb should it ever be needed.
Note that this also fixes the wMaxPacketSize being incorrectly reported
on big-endian systems due to a missing le16_to_cpu().
Signed-off-by: Johan Hovold <johan@kernel.org>
We need to delete un-finished td from current request's td list
at ep_dequeue API, otherwise, this non-user td will be remained
at td list before this request is freed. So if we do ep_queue->
ep_dequeue->ep_queue sequence, when the complete interrupt for
the second ep_queue comes, we search td list for this request,
the first td (added by the first ep_queue) will be handled, and
its status is still active, so we will consider the this transfer
still not be completed, but in fact, it has completed. It causes
the peripheral side considers it never receives current data for
this transfer.
We met this problem when do "Error Recovery Test - Device Configured"
test item for USBCV2 MSC test, the host has never received ACK for
the IN token for CSW due to peripheral considers it does not get this
CBW, the USBCV test log like belows:
--------------------------------------------------------------------------
INFO
Issuing BOT MSC Reset, reset should always succeed
INFO
Retrieving status on CBW endpoint
INFO
CBW endpoint status = 0x0
INFO
Retrieving status on CSW endpoint
INFO
CSW endpoint status = 0x0
INFO
Issuing required command (Test Unit Ready) to verify device has recovered
INFO
Issuing CBW (attempt #1):
INFO
|----- CBW LUN = 0x0
INFO
|----- CBW Flags = 0x0
INFO
|----- CBW Data Transfer Length = 0x0
INFO
|----- CBW CDB Length = 0x6
INFO
|----- CBW CDB-00 = 0x0
INFO
|----- CBW CDB-01 = 0x0
INFO
|----- CBW CDB-02 = 0x0
INFO
|----- CBW CDB-03 = 0x0
INFO
|----- CBW CDB-04 = 0x0
INFO
|----- CBW CDB-05 = 0x0
INFO
Issuing CSW : try 1
INFO
CSW Bulk Request timed out!
ERROR
Failed CSW phase : should have been success or stall
FAIL
(5.3.4) The CSW status value must be 0x00, 0x01, or 0x02.
ERROR
BOTCommonMSCRequest failed: error=80004000
Cc: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
Cc: stable@vger.kernel.org
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch makes the msm ehci driver available to use on QCOM SOCs,
which have the same IP.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some buggy JMicron USB-ATA bridges don't know how to translate the FUA
bit in READs or WRITEs. This patch adds an entry in unusual_devs.h
and a blacklist flag to tell the sd driver not to use FUA.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Michael Büsch <m@bues.ch>
Tested-by: Michael Büsch <m@bues.ch>
Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
CC: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A few more fixes for this RC cycle. There's a revert of a previous patch
which ended up being the wrong version, so we reverted that commit and
applied a better fix.
CPPI41 got a race condition fix which was found by Thomas Gleixner.
The MSM PHY driver got a runtime pm usage fix so that it wouldn't
kill the PHY while it was still being used.
We also have a fix for a panic caused when removing musb_am335x driver.
Other than that, a few other minor fixes.
Signed-of-by: Felipe Balbi <balbi@ti.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=7Mt5
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v3.16-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v3.16-rc4
A few more fixes for this RC cycle. There's a revert of a previous patch
which ended up being the wrong version, so we reverted that commit and
applied a better fix.
CPPI41 got a race condition fix which was found by Thomas Gleixner.
The MSM PHY driver got a runtime pm usage fix so that it wouldn't
kill the PHY while it was still being used.
We also have a fix for a panic caused when removing musb_am335x driver.
Other than that, a few other minor fixes.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Use clk_prepare_enable/clk_disable_unprepare to make the driver
work properly with common clock framework.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The musb/cppi41 code installs a hrtimer to work around DMA completion
interrupts that have fired too early on AM335x hardware. This timer
is currently programmed to first fire 140 microseconds after the DMA
completion callback. According to the commit which introduced it
(a655f481d8, "usb: musb: musb_cppi41: handle pre-mature TX complete
interrupt"), that value is is considered a 'rule of thumb' that worked
well with the test case described in the commit log.
Test show, however, that for USB audio devices and much smaller packet
sizes, the timer has to fire earlier in order to correctly handle the audio
stream. The original test case had output transfer sizes of 1514 bytes, and
a delay of 140 microseconds. For audio devices with 24 bytes channel size, 3
microseconds seem to work well.
Hence, let's assume that the time it takes to clear the bit correlates with
the number of bytes transferred. The referenced commit log mentions such a
suspicion as well. Let the timer fire in cppi41_channel->total_len/10
microseconds to correctly handle both cases.
Also, shorten the interval in which the timer fires again in case of
a non-empty early_tx list.
With these changes in place, both FS and HS audio devices appear to work
well on AM335x hardware.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This reverts commit 1af54b7a4.
The commit tried to address cases in which isochronous transfers are 'not
reliable', most probably in the tests conducted, polling for the
MUSB_TXCSR_TXPKTRDY bit in MUSB_TXCSR is done too late.
Hence, it installs a work struct which basically busy-polls for the bit in a
rather agressive way by rescheduling the work if the FIFO is not empty. With
USB audio devices, tests have shown that it takes approximately 100
iterations of the asynchronous worker until the FIFO signals completion,
which leads to 100% CPU loads when streaming audio.
The issue the patch tried to address can be handled differently, which is
what the next patch does.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Sebastian Reimers <sebastian.reimers@googlemail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
