Move some definitions for max integer values out of the rbd code and
into the more central "decode.h" header file. These really belong
in a Linux (or libc) header somewhere, but I haven't gotten around
to proposing that yet.
This is in preparation for moving some code out of rbd.c and into
the osd client.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The length of outgoing data in an osd request is dependent on the
osd ops that are embedded in that request. Each op is encoded into
a request message using osd_req_encode_op(), so that should be used
to determine the amount of outgoing data implied by the op as it
is encoded.
Have osd_req_encode_op() return the number of bytes of outgoing data
implied by the op being encoded, and accumulate and use that in
ceph_osdc_build_request().
As a result, ceph_osdc_build_request() no longer requires its "len"
parameter, so get rid of it.
Using the sum of the op lengths rather than the length provided is
a valid change because:
- The only callers of osd ceph_osdc_build_request() are
rbd and the osd client (in ceph_osdc_new_request() on
behalf of the file system).
- When rbd calls it, the length provided is only non-zero for
write requests, and in that case the single op has the
same length value as what was passed here.
- When called from ceph_osdc_new_request(), (it's not all that
easy to see, but) the length passed is also always the same
as the extent length encoded in its (single) write op if
present.
This resolves:
http://tracker.ceph.com/issues/4406
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Record the byte count for an osd request rather than the page count.
The number of pages can always be derived from the byte count (and
alignment/offset) but the reverse is not true.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An osd request defines information about where data to be read
should be placed as well as where data to write comes from.
Currently these are represented by common fields.
Keep information about data for writing separate from data to be
read by splitting these into data_in and data_out fields.
This is the key patch in this whole series, in that it actually
identifies which osd requests generate outgoing data and which
generate incoming data. It's less obvious (currently) that an osd
CALL op generates both outgoing and incoming data; that's the focus
of some upcoming work.
This resolves:
http://tracker.ceph.com/issues/4127
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An osd request uses either pages or a bio list for its data. Use a
union to record information about the two, and add a data type
tag to select between them.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Pull the fields in an osd request structure that define the data for
the request out into a separate structure.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
It's possible that the reference to the object request dropped
inside the loop in rbd_img_request_submit() will be the last
one, in which case the content of the object pointer can't be
trusted.
Use a safe form of the object request list traversal to avoid
problems.
This resolves:
http://tracker.ceph.com/issues/4705
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
A result of ENOENT from a read request for an object that's part of
an rbd image indicates that there is a hole in that portion of the
image. Similarly, a short read for such an object indicates that
the remainder of the read should be interpreted a full read with
zeros filling out the end of the request.
This behavior is not correct for objects that are not backing rbd
image data. Currently rbd_img_obj_request_callback() assumes it
should be done for all objects.
Change rbd_img_obj_request_callback() so it only does this zeroing
for image objects. Encapsulate that special handling in its own
function. Add an assertion that the image object request is a bio
request, since we assume that (and we currently don't support any
other types).
This resolves a problem identified here:
http://tracker.ceph.com/issues/4559
The regression was introduced by bf0d5f503d.
Reported-by: Dan van der Ster <dan@vanderster.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-off-by: Sage Weil <sage@inktank.com>
Use the new version of the encoding for osd requests and replies. In the
process, update the way we are tracking request ops and reply lengths and
results in the struct ceph_osd_request. Update the rbd and fs/ceph users
appropriately.
The main changes are:
- we keep pointers into the request memory for fields we need to update
each time the request is sent out over the wire
- we keep information about the result in an array in the request struct
where the users can easily get at it.
Signed-off-by: Sage Weil <sage@inktank.com>
Reviewed-by: Alex Elder <elder@inktank.com>
The only thing type-specific osd completion functions do with their
osd op parameter is (in some cases) extract the number of bytes
transferred from it. In the other cases, the xferred bytes field
is not used, and total message data transfer byte count (which may
well be zero) is used.
Just set the object request transfer count in the main osd request
callback function and provide that to the other routines. There is
then no longer any need to pass the op pointer to the type-specific
completion routines, so drop those parameters.
Stop doing anything with the total message data length.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
This function is slightly out of place, probably the result
of an errant automatic merge or something.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
Fengguang Wu reminded me that there were outstanding sparse reports
in the ceph and rbd code. This patch fixes these problems in rbd
that lead to those reports:
- Convert functions that are never referenced externally to have
static scope.
- Add a lockdep annotation to rbd_request_fn(), because it
releases a lock before acquiring it again.
This partially resolves:
http://tracker.ceph.com/issues/4184
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add dout() calls to facilitate tracing of image and object requests.
Change a few existing calls so they use __func__ rather than the
hard-coded function name. Have calls always add ":" after the name
of the function, and prefix pointer values with a consistent tag
indicating what it represents. (Note that there remain some older
dout() calls that are left untouched by this patch.)
Issue a warning if rbd_osd_write_callback() ever gets a short write.
This resolves:
http://tracker.ceph.com/issues/4235
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Let's go shopping!
I'm afraid this may not have gotten it right:
07741308 rbd: add barriers near done flag operations
The smp_wmb() should have been done *before* setting the done flag,
to ensure all other data was valid before marking the object request
done.
Switch to use atomic_inc_return() here to set the done flag, which
allows us to verify we don't mark something done more than once.
Doing this also implies general barriers before and after the call.
And although a read memory barrier might have been sufficient before
reading the done flag, convert this to a full memory barrier just
to put this issue to bed.
This resolves:
http://tracker.ceph.com/issues/4238
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The old request code simply ignored zero-length requests. We should
still operate that same way to avoid any changes in behavior. We
can implement handling for special zero-length requests separately
(see http://tracker.ceph.com/issues/4236).
Add some assertions based on this new constraint.
This resolves:
http://tracker.ceph.com/issues/4237
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The return values provided for ceph_copy_to_page_vector() and
ceph_copy_from_page_vector() serve no purpose, so get rid of them.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The result of ceph_copy_from_page_vector() is simply the length
argument it is provided.
This is called by rbd_obj_method_sync(), which returns the result if
it's non-negative. But we always either ignore or overwrite that
return value. So explicitly ignore what's returned by the copy
function, and have rbd_obj_method_sync() always return either a
negative errno or 0.
We also return the result of ceph_copy_from_page_vector() in
rbd_obj_read_sync(). There we still want to return the number of
bytes transferred, but we can use the value we already have in hand
rather than what ceph_copy_from_page_vector() provides.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In rbd_obj_read_sync(), verify the number of bytes transferred won't
exceed what can be represented by a size_t before using it to
indicate the number of bytes to copy to the result buffer.
(The real motivation for this is to prepare for the next patch.)
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add support for CEPH_OSD_OP_STAT operations in the osd client
and in rbd.
This operation sends no data to the osd; everything required is
encoded in identity of the target object.
The result will be ENOENT if the object doesn't exist. If it does
exist and no other error occurs the server returns the size and last
modification time of the target object as output data (in little
endian format). The size is a 64 bit unsigned and the time is
ceph_timespec structure (two unsigned 32-bit integers, representing
a seconds and nanoseconds value).
This resolves:
http://tracker.ceph.com/issues/4007
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The for_each_obj_request*() macros should parenthesize their uses of
the ireq parameter.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is only one caller of ceph_osdc_create_event(), and it
provides 0 as its "one_shot" argument. Get rid of that argument and
just use 0 in its place.
Replace the code in handle_watch_notify() that executes if one_shot
is nonzero in the event with a BUG_ON() call.
While modifying "osd_client.c", give handle_watch_notify() static
scope.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Somehow, I missed this little item in Documentation/atomic_ops.txt:
*** WARNING: atomic_read() and atomic_set() DO NOT IMPLY BARRIERS! ***
Create and use some helper functions that include the proper memory
barriers for manipulating the done field.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This commit:
bc7a62ee5 rbd: prevent open for image being removed
added checking for removing rbd before allowing an open, and used
the same request spinlock for protecting that and updating the open
count as is used for the request queue.
However it used the non-irq protected version of the spinlocks.
Fix that.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is a check in the completion path for osd requests that
ensures the number of pages allocated is enough to hold the amount
of incoming data expected.
For bio requests coming from rbd the "number of pages" is not really
meaningful (although total length would be). So stop requiring that
nr_pages be supplied for bio requests. This is done by checking
whether the pages pointer is null before checking the value of
nr_pages.
Note that this value is passed on to the messenger, but there it's
only used for debugging--it's never used for validation.
While here, change another spot that used r_pages in a debug message
inappropriately, and also invalidate the r_con_filling_msg pointer
after dropping a reference to it.
This resolves:
http://tracker.ceph.com/issues/3875
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Currently, if the OSD client finds an osd request has had a bio list
attached to it, it drops a reference to it (or rather, to the first
entry on that list) when the request is released.
The code that added that reference (i.e., the rbd client) is
therefore required to take an extra reference to that first bio
structure.
The osd client doesn't really do anything with the bio pointer other
than transfer it from the osd request structure to outgoing (for
writes) and ingoing (for reads) messages. So it really isn't the
right place to be taking or dropping references.
Furthermore, the rbd client already holds references to all bio
structures it passes to the osd client, and holds them until the
request is completed. So there's no need for this extra reference
whatsoever.
So remove the bio_put() call in ceph_osdc_release_request(), as
well as its matching bio_get() call in rbd_osd_req_create().
This change could lead to a crash if old libceph.ko was used with
new rbd.ko. Add a compatibility check at rbd initialization time to
avoid this possibilty.
This resolves:
http://tracker.ceph.com/issues/3798 and
http://tracker.ceph.com/issues/3799
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
An open request for a mapped rbd image can arrive while removal of
that mapping is underway. We need to prevent such an open request
from succeeding. (It appears that Maciej Galkiewicz ran into this
problem.)
Define and use a "removing" flag to indicate a mapping is getting
removed. Set it in the remove path after verifying nothing holds
the device open. And check it in the open path before allowing the
open to proceed. Acquire the rbd device's lock around each of these
spots to avoid any races accessing the flags and open_count fields.
This addresses:
http://tracker.newdream.net/issues/3427
Reported-by: Maciej Galkiewicz <maciejgalkiewicz@ragnarson.com>
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Define a new rbd device flags field, manipulated using bit
operations. Replace the use of the current "exists" flag with a bit
in this new "flags" field. Add a little commentary about the
"exists" flag, which does not need to be manipulated atomically.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When we register an osd request to linger, it means that request
will stay around (under control of the osd client) until we've
unregistered it. We do that for an rbd image's header object, and
we keep a pointer to the object request associated with it.
Keep a reference to the watch object request for as long as it is
registered to linger. Drop it again after we've removed the linger
registration.
This resolves:
http://tracker.ceph.com/issues/3937
(Note: this originally came about because the osd client was
issuing a callback more than once. But that behavior will be
changing soon, documented in tracker issue 3967.)
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Decrement the obj_request_count value when deleting an object
request from its image request's list. Rearrange a few lines
in the surrounding code.
This resolves:
http://tracker.ceph.com/issues/3940
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Switch to keeping track of the object request pointer rather than
the osd request used to watch the rbd image header object.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Move the code that unregisters an rbd device's lingering header
object watch request into rbd_dev_header_watch_sync(), so it
occurs in the same function that originally sets up that request.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Get rid rbd_req_sync_exec() because it is no longer used. That
eliminates the last use of rbd_req_sync_op(), so get rid of that
too. And finally, that leaves rbd_do_request() unreferenced, so get
rid of that.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Reimplement synchronous object method calls using the new request
tracking code. Use the name rbd_obj_method_sync()
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When we receive notification of a change to an rbd image's header
object we need to refresh our information about the image (its
size and snapshot context). Once we have refreshed our rbd image
we need to acknowledge the notification.
This acknowledgement was previously done synchronously, but there's
really no need to wait for it to complete.
Change it so the caller doesn't wait for the notify acknowledgement
request to complete. And change the name to reflect it's no longer
synchronous.
This resolves:
http://tracker.newdream.net/issues/3877
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Get rid rbd_req_sync_notify_ack() because it is no longer used.
As a result rbd_simple_req_cb() becomes unreferenced, so get rid
of that too.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Use the new object request tracking mechanism for handling a
notify_ack request.
Move the callback function below the definition of this so we don't
have to do a pre-declaration.
This resolves:
http://tracker.newdream.net/issues/3754
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Get rid of rbd_req_sync_watch(), because it is no longer used.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Implement a new function to set up or tear down a watch event
for an mapped rbd image header using the new request code.
Create a new object request type "nodata" to handle this. And
define rbd_osd_trivial_callback() which simply marks a request done.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Delete rbd_req_sync_read() is no longer used, so get rid of it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Reimplement the synchronous read operation used for reading a
version 1 header using the new request tracking code. Name the
resulting function rbd_obj_read_sync() to better reflect that
it's a full object operation, not an object request. To do this,
implement a new OBJ_REQUEST_PAGES object request type.
This implements a new mechanism to allow the caller to wait for
completion for an rbd_obj_request by calling rbd_obj_request_wait().
This partially resolves:
http://tracker.newdream.net/issues/3755
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The two remaining callers of rbd_do_request() always pass a null
collection pointer, so the "coll" and "coll_index" parameters are
not needed. There is no other use of that data structure, so it
can be eliminated.
Deleting them means there is no need to allocate a rbd_request
structure for the callback function. And since that's the only use
of *that* structure, it too can be eliminated.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Now that the request function has been replaced by one using the new
request management data structures the old one can go away.
Deleting it makes rbd_dev_do_request() no longer needed, and
deleting that makes other functions unneeded, and so on.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This patch fully implements the new request tracking code for rbd
I/O requests.
Each I/O request to an rbd image will get an rbd_image_request
structure allocated to track it. This provides access to all
information about the original request, as well as access to the
set of one or more object requests that are initiated as a result
of the image request.
An rbd_obj_request structure defines a request sent to a single osd
object (possibly) as part of an rbd image request. An rbd object
request refers to a ceph_osd_request structure built up to represent
the request; for now it will contain a single osd operation. It
also provides space to hold the result status and the version of the
object when the osd request completes.
An rbd_obj_request structure can also stand on its own. This will
be used for reading the version 1 header object, for issuing
acknowledgements to event notifications, and for making object
method calls.
All rbd object requests now complete asynchronously with respect
to the osd client--they supply a common callback routine.
This resolves:
http://tracker.newdream.net/issues/3741
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When an rbd image is initially mapped a watch event is registered so
we can do something if the header object changes.
The code that does this currently loops if initiating the watch
request results in an ERANGE error. The osds will never return
ERANGE, so there's no reason to do this loop, so get rid of it.
This resolves:
http://tracker.newdream.net/issues/3860
Note that the problem this loop was intended to solve is a race
between collecting image header information and setting up the watch
on the header object. The real fix for that problem is described
here:
http://tracker.newdream.net/issues/3871
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The return type of rbd_get_num_segments() is int, but the values it
operates on are u64. Although it's not likely, there's no guarantee
the result won't exceed what can be respresented in an int. The
function is already designed to return -ERANGE on error, so just add
this possible overflow as another reason to return that.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
A few very minor changes to the rbd code:
- RBD_MAX_OPT_LEN is unused, so get rid of it
- Consolidate rbd options definitions
- Make rbd_segment_name() return pointer to const char
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The type of the snap_id local variable is defined with the
wrong byte order. Fix that.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Both rbd_req_sync_op() and rbd_do_request() have a "linger"
parameter, which is the address of a pointer that should refer to
the osd request structure used to issue a request to an osd.
Only one case ever supplies a non-null "linger" argument: an
CEPH_OSD_OP_WATCH start. And in that one case it is assigned
&rbd_dev->watch_request.
Within rbd_do_request() (where the assignment ultimately gets made)
we know the rbd_dev and therefore its watch_request field. We
also know whether the op being sent is CEPH_OSD_OP_WATCH start.
Stop opaquely passing down the "linger" pointer, and instead just
assign the value directly inside rbd_do_request() when it's needed.
This makes it unnecessary for rbd_req_sync_watch() to make
arrangements to hold a value that's not available until a
bit later. This more clearly separates setting up a watch
request from submitting it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The two remaining osd ops used by rbd are CEPH_OSD_OP_WATCH and
CEPH_OSD_OP_NOTIFY_ACK. Move the setup of those operations into
rbd_osd_req_op_create(), and get rid of rbd_create_rw_op() and
rbd_destroy_op().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Move the initialization of the CEPH_OSD_OP_CALL operation into
rbd_osd_req_op_create().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Move the assignment of the extent offset and length and payload
length out of rbd_req_sync_op() and into its caller in the one spot
where a read (and note--no write) operation might be initiated.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In rbd_do_request() there's a sort of last-minute assignment of the
extent offset and length and payload length for read and write
operations. Move those assignments into the caller (in those spots
that might initiate read or write operations)
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When rbd_req_sync_notify_ack() calls rbd_do_request() it supplies
rbd_simple_req_cb() as its callback function. Because the callback
is supplied, an rbd_req structure gets allocated and populated so it
can be used by the callback. However rbd_simple_req_cb() is not
freeing (or even using) the rbd_req structure, so it's getting
leaked.
Since rbd_simple_req_cb() has no need for the rbd_req structure,
just avoid allocating one for this case. Of the three calls to
rbd_do_request(), only the one from rbd_do_op() needs the rbd_req
structure, and that call can be distinguished from the other two
because it supplies a non-null rbd_collection pointer.
So fix this leak by only allocating the rbd_req structure if a
non-null "coll" value is provided to rbd_do_request().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When rbd_do_request() is called it allocates and populates an
rbd_req structure to hold information about the osd request to be
sent. This is done for the benefit of the callback function (in
particular, rbd_req_cb()), which uses this in processing when
the request completes.
Synchronous requests provide no callback function, in which case
rbd_do_request() waits for the request to complete before returning.
This case is not handling the needed free of the rbd_req structure
like it should, so it is getting leaked.
Note however that the synchronous case has no need for the rbd_req
structure at all. So rather than simply freeing this structure for
synchronous requests, just don't allocate it to begin with.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The rbd_req_sync_watch() and rbd_req_sync_unwatch() functions are
nearly identical. Combine them into a single function with a flag
indicating whether a watch is to be initiated or torn down.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Each osd message includes a layout structure, and for rbd it is
always the same (at least for osd's in a given pool).
Initialize a layout structure when an rbd_dev gets created and just
copy that into osd requests for the rbd image.
Replace an assertion that was done when initializing the layout
structures with code that catches and handles anything that would
trigger the assertion as soon as it is identified. This precludes
that (bad) condition from ever occurring.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
When rbd_do_request() has a request to process it initializes a ceph
file layout structure and uses it to compute offsets and limits for
the range of the request using ceph_calc_file_object_mapping().
The layout used is fixed, and is based on RBD_MAX_OBJ_ORDER (30).
It sets the layout's object size and stripe unit to be 1 GB (2^30),
and sets the stripe count to be 1.
The job of ceph_calc_file_object_mapping() is to determine which
of a sequence of objects will contain data covered by range, and
within that object, at what offset the range starts. It also
truncates the length of the range at the end of the selected object
if necessary.
This is needed for ceph fs, but for rbd it really serves no purpose.
It does its own blocking of images into objects, echo of which is
(1 << obj_order) in size, and as a result it ignores the "bno"
value returned by ceph_calc_file_object_mapping(). In addition,
by the point a request has reached this function, it is already
destined for a single rbd object, and its length will not exceed
that object's extent. Because of this, and because the mapping will
result in blocking up the range using an integer multiple of the
image's object order, ceph_calc_file_object_mapping() will never
change the offset or length values defined by the request.
In other words, this call is a big no-op for rbd data requests.
There is one exception. We read the header object using this
function, and in that case we will not have already limited the
request size. However, the header is a single object (not a file or
rbd image), and should not be broken into pieces anyway. So in fact
we should *not* be calling ceph_calc_file_object_mapping() when
operating on the header object.
So...
Don't call ceph_calc_file_object_mapping() in rbd_do_request(),
because useless for image data and incorrect to do sofor the image
header.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This patch gets rid of rbd_calc_raw_layout() by simply open coding
it in its one caller.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This is the first in a series of patches aimed at eliminating
the use of ceph_calc_raw_layout() by rbd.
It simply pulls in a copy of that function and renames it
rbd_calc_raw_layout().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
We now know that every of rbd_req_sync_op() passes an array of
exactly one operation, as evidenced by all callers passing 1 as its
num_op argument. So get rid of that argument, assuming a single op.
Similarly, we now know that all callers of rbd_do_request() pass 1
as the num_op value, so that parameter can be eliminated as well.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Throughout the rbd code there are spots where it appears we can
handle an osd request containing more than one osd request op.
But that is only the way it appears. In fact, currently only one
operation at a time can be supported, and supporting more than
one will require much more than fleshing out the support that's
there now.
This patch changes names to make it perfectly clear that anywhere
we're dealing with a block of ops, we're in fact dealing with
exactly one of them. We'll be able to simplify some things as
a result.
When multiple op support is implemented, we can update things again
accordingly.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Both ceph_osdc_alloc_request() and ceph_osdc_build_request() are
provided an array of ceph osd request operations. Rather than just
passing the number of operations in the array, the caller is
required append an additional zeroed operation structure to signal
the end of the array.
All callers know the number of operations at the time these
functions are called, so drop the silly zero entry and supply that
number directly. As a result, get_num_ops() is no longer needed.
This also means that ceph_osdc_alloc_request() never uses its ops
argument, so that can be dropped.
Also rbd_create_rw_ops() no longer needs to add one to reserve room
for the additional op.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add a num_op parameter to rbd_do_request() and rbd_req_sync_op() to
indicate the number of entries in the array. The callers of these
functions always know how many entries are in the array, so just
pass that information down.
This is in anticipation of eliminating the extra zero-filled entry
in these ops arrays.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Only one of the two callers of ceph_osdc_alloc_request() provides
page or bio data for its payload. And essentially all that function
was doing with those arguments was assigning them to fields in the
osd request structure.
Simplify ceph_osdc_alloc_request() by having the caller take care of
making those assignments
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The only thing ceph_osdc_alloc_request() really does with the
flags value it is passed is assign it to the newly-created
osd request structure. Do that in the caller instead.
Both callers subsequently call ceph_osdc_build_request(), so have
that function (instead of ceph_osdc_alloc_request()) issue a warning
if a request comes through with neither the read nor write flags set.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The osdc parameter to ceph_calc_raw_layout() is not used, so get rid
of it. Consequently, the corresponding parameter in calc_layout()
becomes unused, so get rid of that as well.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
A snapshot id must be provided to ceph_calc_raw_layout() even though
it is not needed at all for calculating the layout.
Where the snapshot id *is* needed is when building the request
message for an osd operation.
Drop the snapid parameter from ceph_calc_raw_layout() and pass
that value instead in ceph_osdc_build_request().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The len argument to ceph_osdc_build_request() is set up to be
passed by address, but that function never updates its value
so there's no need to do this. Tighten up the interface by
passing the length directly.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
For some reason, the snapid field of the osd request header is
explicitly set to CEPH_NOSNAP in rbd_do_request(). Just a few lines
later--with no code that would access this field in between--a call
is made to ceph_calc_raw_layout() passing the snapid provided to
rbd_do_request(), which encodes the snapid value it is provided into
that field instead.
In other words, there is no need to fill in CEPH_NOSNAP, and doing
so suggests it might be necessary. Don't do that any more.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The snapc and snapid parameters to rbd_req_sync_op() always take
the values NULL and CEPH_NOSNAP, respectively. So just get rid
of them and use those values where needed.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
All callers of rbd_req_sync_exec() pass CEPH_OSD_FLAG_READ as their
flags argument. Delete that parameter and use CEPH_OSD_FLAG_READ
within the function. If we find a need to support write operations
we can add it back again.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is only one caller of rbd_req_sync_read(), and it passes
CEPH_NOSNAP as the snapshot id argument. Delete that parameter
and just use CEPH_NOSNAP within the function.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The last two parameters to ceph_osd_build_request() describe the
object id, but the values passed always come from the osd request
structure whose address is also provided. Get rid of those last
two parameters.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Pull a block of code that initializes the layout structure in an osd
request into its own function so it can be reused.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Right now we get the snapshot context for an rbd image (under
protection of the header semaphore) for every request processed.
There's no need to get the snap context if we're doing a read,
so avoid doing so in that case.
Note that we no longer need to hold the header semaphore to
check the rbd_dev's existence flag.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The rbd_device->exists field can be updated asynchronously, changing
from set to clear if a mapped snapshot disappears from the base
image's snapshot context.
Currently, value of the "exists" flag is only read and modified
under protection of the header semaphore, but that will change with
the next patch. Making it atomic ensures this won't be a problem
because the a the non-existence of device will be immediately known.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Now that a big hunk in the middle of rbd_rq_fn() has been moved
into its own routine we can simplify it a little more.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Only one of the three callers of rbd_do_request() provide a
collection structure to aggregate status.
If an error occurs in rbd_do_request(), have the caller
take care of calling rbd_coll_end_req() if necessary in
that one spot.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
In rbd_rq_fn(), requests are fetched from the block layer and each
request is processed, looping through the request's list of bio's
until they've all been consumed.
Separate the handling for a single request into its own function to
make it a bit easier to see what's going on.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The result field in a ceph osd reply header is a signed 32-bit type,
but rbd code often casually uses int to represent it.
The following changes the types of variables that handle this result
value to be "s32" instead of "int" to be completely explicit about
it. Only at the point we pass that result to __blk_end_request()
does the type get converted to the plain old int defined for that
interface.
There is almost certainly no binary impact of this change, but I
prefer to show the exact size and signedness of the value since we
know it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
There are spots where a ceph_osds_request pointer variable is given
the name "req". Since we're dealing with (at least) three types of
requests (block layer, rbd, and osd), I find this slightly
distracting.
Change such instances to use "osd_req" consistently to make the
abstraction represented a little more obvious.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There are two names used for items of rbd_request structure type:
"req" and "req_data". The former name is also used to represent
items of pointers to struct ceph_osd_request.
Change all variables that have these names so they are instead
called "rbd_req" consistently.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Josh suggested adding warnings to this function to help users
diagnose problems.
Other than memory allocatino errors, there are two places where
errors can be returned. Both represent problems that should
have been caught earlier, and as such might well have been
handled with BUG_ON() calls. But if either ever did manage to
happen, it will be reported.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add a warning in bio_chain_clone_range() to help a user determine
what exactly might have led to a failure. There is only one; please
say something if you disagree with the following reasoning.
There are three places this can return abnormally:
- Initially, if there is nothing to clone. It turns out that
right now this cannot happen anyway. The test is in place
because the code below it doesn't work if those conditions
don't hold. As such they could be assertions but since I can
return a null to indicate an error I just do that instead.
I have not added a warning here because it won't happen.
- While processing bio's, if none remain but there are supposed
to be more bytes to clone. Here I have added a warning.
- If bio_clone_range() returns a null pointer. That function
will have already produced a warning (at least the first
time, via WARN_ON_ONCE()) to distinguish the cause of the
error. The only exception is memory exhaustion, and I'd
rather not pepper the code with warnings in all those spots.
So no warning is added in that place.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Tell the user (via dmesg) what was wrong with the arguments provided
via /sys/bus/rbd/add.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Define a new function rbd_warn() that produces a boilerplate warning
message, identifying in the resulting message the affected rbd
device in the best way available. Use it in a few places that now
use pr_warning().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
This replaces two kmalloc()/memcpy() combinations with a single
call to kmemdup().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There is no real benefit to keeping the length of an image id, so
get rid of it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
There may have been a benefit to hanging on to the length of an
image name before, but there is really none now. The only time it's
used is when probing for rbd images, so we can just compute the
length then.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
I promised Josh I would document whether there were any restrictions
needed for accessing fields of an rbd_spec structure. This adds a
big block of comments that documents the structure and how it is
used--including the fact that we don't attempt to synchronize access
to it.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
The functions rbd_get_dev() and rbd_put_dev() are trivial wrappers
that add no value, and their existence suggests they may do more
than what they do.
Get rid of them.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Dan Mick <dan.mick@inktank.com>
ENOTSUPP is not a standard errno (it shows up as "Unknown error 524"
in an error message). This is what was getting produced when the
the local rbd code does not implement features required by a
discovered rbd image.
Change the error code returned in this case to ENXIO.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
RBD_MAX_SEG_NAME_LEN represents the maximum length of an rbd object
name (i.e., one of the objects providing storage backing an rbd
image).
Another symbol, MAX_OBJ_NAME_SIZE, is used in the osd client code to
define the maximum length of any object name in an osd request.
Right now they disagree, with RBD_MAX_SEG_NAME_LEN being too big.
There's no real benefit at this point to defining the rbd object
name length limit separate from any other object name, so just
get rid of RBD_MAX_SEG_NAME_LEN and use MAX_OBJ_NAME_SIZE in its
place.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
There is no check in rbd_remove() to see if anybody holds open the
image being removed. That's not cool.
Add a simple open count that goes up and down with opens and closes
(releases) of the device, and don't allow an rbd image to be removed
if the count is non-zero.
Protect the updates of the open count value with ctl_mutex to ensure
the underlying rbd device doesn't get removed while concurrently
being opened.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
When a layered rbd image has a parent, that parent is identified
only by its pool id, image id, and snapshot id. Images that have
been mapped also record *names* for those three id's.
Add code to look up these names for parent images so they match
mapped images more closely. Skip doing this for an image if it
already has its pool name defined (this will be the case for images
mapped by the user).
It is possible that an the name of a parent image can't be
determined, even if the image id is valid. If this occurs it
does not preclude correct operation, so don't treat this as
an error.
On the other hand, defined pools will always have both an id and a
name. And any snapshot of an image identified as a parent for a
clone image will exist, and will have a name (if not it indicates
some other internal error). So treat failure to get these bits
of information as errors.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Add support for getting the the information identifying the parent
image for rbd images that have them. The child image holds a
reference to its parent image specification structure. Create a new
entry "parent" in /sys/bus/rbd/image/N/ to report the identifying
information for the parent image, if any.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Format 2 parent images are partially identified by their image id,
but it may not be possible to determine their image name. The name
is not strictly needed for correct operation, so we won't be
treating it as an error if we don't know it. Handle this case
gracefully in rbd_name_show().
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
We will know the image id for format 2 parent images, but won't
initially know its image name. Avoid making the query for an image
id in rbd_dev_image_id() if it's already known.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Group the activities that now take place after an rbd_dev_probe()
call into a single function, and move the call to that function
into rbd_dev_probe() itself.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
Encapsulate the creation/initialization and destruction of rbd
device structures. The rbd_client and the rbd_spec structures
provided on creation hold references whose ownership is transferred
to the new rbd_device structure.
Signed-off-by: Alex Elder <elder@inktank.com>
Reviewed-by: Josh Durgin <josh.durgin@inktank.com>
