Reading the ELP_CTRL register with sdio_readb causes problems because
hardware seems to be performing a write using stuff bits in the request
(those bits contain write data in write request). This indicates that it
actually expects RAW (read after write) type of request, so perform that
when reading ELP_CTRL instead. Also cache last written value so we know
what to write when doing RAW request.
Because of the above it was not possible to wake the chip from ELP power
saving mode, PM had to be disabled to have the driver usable in SDIO
mode. After this patch PM is functional.
For backporting to 2.6.34 or earlier, this patch depends on
6c1f716e81, which adds the
required SDIO funcion.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251_sdio_probe() error path is missing wl1251_free_hw, add it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 5GHz bands were scanned without the proper IE's in place, preventing
proper 5GHz scanning. This patches fixes the problem by storing a pointer
to the scan request (with the IE's) for all iterations of scan.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A fixed 1 mbps rate was used for the PSM entry/exit null-func frames. Fix this
by using the basic rates instead.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The core wl1271 module can also be used with SDIO, so it should not depend on
SPI_MASTER.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The mac80211 changes to idle almost immediately after transmitting some
frames, such as deauth etc. When going to idle, the wl1271 is disconnected,
which causes TX frames already on buffers, but not yet transmitted, to be
deleted.
To make sure deauth frames reach the air, allow the TX buffers to flush
before proceeding to idle.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As there is more and more stuff triggered by going in and out of idle,
create a separate function for handling that.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl1271 uses a session counter in CMD_JOIN and TX frame descriptors. This
counter is used to determine which frames to drop when the CMD_JOIN is
executed.
The driver executes CMD_JOIN multiple times upon association and sometimes
disassociation, and we don't want any frames to get lost.
Fix this by incrementing the session counter only when leaving idle (not every
CMD_JOIN as before.) Also, remove the TX flush flag from the CMD_JOIN options.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use kmemdup when some other buffer is immediately copied into the
allocated region.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression from,to,size,flag;
statement S;
@@
- to = \(kmalloc\|kzalloc\)(size,flag);
+ to = kmemdup(from,size,flag);
if (to==NULL || ...) S
- memcpy(to, from, size);
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch adds support for NVS files with 5GHz band parameters. The change
is done in a backward compatible manner - if 11a is not enabled in the driver,
the driver will allow also old NVS files to be loaded.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch updates the handling of the NVS file INI-section, trying to make
it slightly more generic, and exposing the parameters being set. This is done
in preparation for 5GHz parameters.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make it possible to use wl1271's SDIO interface on non-ARM platforms.
Fully tested on a x86 platform, compile-tested on ARM.
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current frame length used by the driver for RX frames is the SPI bus
transfer length. This length has padding bytes, which do not belong to the
WLAN frame.
As there is no other length information in the WLAN frame except the skb
length this problem caused for instance extra ESSID's to be listed at the
end of scan results (IE id 0) with zero length.
Fix the frame length by removing padding.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes from drivers/net/ all the unnecessary
return; statements that precede the last closing brace of
void functions.
It does not remove the returns that are immediately
preceded by a label as gcc doesn't like that.
It also does not remove null void functions with return.
Done via:
$ grep -rP --include=*.[ch] -l "return;\n}" net/ | \
xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }'
with some cleanups by hand.
Compile tested x86 allmodconfig only.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The goto and the break are equivelent. I removed the goto in memory of
Edsger Dijkstra who famously hated gotos and who would have been eighty
years old next Tuesday.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "(wl == NULL)" test doesn't work here because "wl" is always
non-null. The intent of the code is to return if the interface
was not supported by the driver.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We should start the loop consistently with the "wl_lock" lock held.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, we configure a 128ms hang over period for the PSM entry
(the firmware will remain active for 128ms after sending the null func for
PSM and getting an ack for it.) This is a huge power consumption issue, and
appears unnecessary. So, configure the value to 1 ms.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Janne Ylalehto <janne.ylalehto@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incresed the timeout value for command complete event waiting from 100
ms to 750 ms. In some rare cases it can take about 600 ms before
complete event for join command is received. This is most propably
caused by the firmware being busy with scanning related activities.
Signed-off-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch changes the way JOIN's are performed, and channel numbers updated.
The reason for this is that the firmware JOIN command clears WPA(2) key
material, and if done while associated to a WPA(2) secured AP, will render
the data-path unusable.
While the channel is not usually changed while associated (and currently we
could not even support something like that), after performing a scan operation
while associated, mac80211 will re-set the current channel to the driver. This
caused our problem.
Also, the mac80211 is assuming that the driver channel configuration remains
persistent over periods of IDLE. Therefore remove channel resetting to zero
from the unjoin function.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reading single registers did not pay attention to data endianness. This patch
fix that.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch reads the HW PG version (along with a ROM-version, embedded in the
same value) from the wl1271 hardware and publishes the value in a sysfs -file.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
in your merge in 5c01d56693 you added "int
i;" into wl1271_main.c which is unused in that function.
This patch fixes the merge problem:
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple of sparse warnings in some rate settings (missing cpu_to_le32) were
fixed. Changed the conf_sg_settings struct from le to native endianess. The
values are converted to le when copying them to the acx command instead.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver had a join command without keep-alive restart procedures in the
channel changing code. After associated scans, the mac80211 does re-set the
current channel, causing the join to occur. This would stop the hardware
keep alive.
To make the joins safer in this respect, this patch adds a join function that
does the hardware-keep-alive magic along the join. This is now invoked in the
above mentioned scenario, and also other scenarios.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When U-APSD is enabled, device is not sending power save
state notifications to AP using QOS nullfunc frames.
This patch configures nullfunc templates needed for U-APSD.
Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In testing I noticed that the wl1271 commands fall into two categories. In the
first category are "fast" commands, these mostly take only 0 or 1 polls to
complete, but occasionally upto 50 (giving a 0.5ms execution time.) In the
second category, the command completion takes well more than 0.5ms (from
1.5ms upwards.)
This patch fixes command polling such that it is optimal for the fast commands,
but also allows sleep for the longer ones.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When scanning, it is somewhat important to scan
on the correct virtual interface. All drivers
that currently implement hw_scan only support a
single virtual interface, but that may change
and then we'd want to be ready.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 has WLAN_IRQ pin for generating interrupts to host processor,
which is mandatory in SPI mode and optional in SDIO mode (which can
use SDIO interrupts instead). However TI recommends using deditated
IRQ line for SDIO too.
Add support for using dedicated interrupt line with SDIO, but also leave
ability to switch to SDIO interrupts in case it's needed.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Reviewed-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1251 is embedded chip that can be connected using SDIO bus, and is not
an actual SDIO card. For this reason there is a need to pass some board
specific data, like 'EEPROM is attached' flag or power control callback.
However currently there is no way to pass this data through SDIO subsystem,
so this patch registers dummy platform_device to allow that, until we
have a better solution to this.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some wl1251 hardware configurations (like in WG7210 module) have
EEPROM attached where NVS data is kept, which includes MAC address.
In such configurations, let's read default MAC address from EEPROM,
instead of using random one.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If EEPROM is used, NVS data is now loaded but ignored.
Stop loading it to avoid need of dummy NVS file for modules with EEPROM.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Acked-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch will add support for connection quality monitoring by configuring
rssi triggers to the firmware, and enabling the firmware rssi trigger
functionality.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow the wl1271 go to ELP mode also in idle. This will reduce current
consumption remarkably in idle mode (~12mA -> ~0.2mA)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 sends RTS threshold configuration request even if the wl1271 interface
state is WL1271_STATE_OFF. This leads to failures during pm tests.
This patch leaves the configuration function, if the interface is
going down.
Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 sends configuration requests even if the wl1271 interface
state is WL1271_STATE_OFF. This creates warnings from mac80211.
This patch leaves the configuration functions, if the interface is
going down.
Signed-off-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes some memory leaks occurring during driver init/de-init.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Better use the macro for consistency, the content is the same anyway.
Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
