There are little changes in core part, but lots of development are
found in drivers, especially ASoC. The diffstat shows regmap-
related changes for a slight API additions / changes, and that's all.
Looking at the code size statistics, the most significant addition
is for Intel Skylake. (Note that SKL support is still underway, the
codec driver is missing.) Also STI controller driver is a major
addition as well as a few new codec drivers.
In HD-audio side, there are fewer changes than the past. The
noticeable change is the support of ELD notification from i915
graphics driver. Thus this pull request carries a few changes in
drm/i915.
Other than that, USB-audio got a rewrite of runtime PM code. It
was initiated by lockdep warning, but resulted in a good cleanup in
the end.
Below are the highlights:
Common:
- Factoring out of AC'97 reset code from ASoC into the core helper
- A few regmap API extensions (in case it's not pulled yet)
ASoC:
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650
- Initial driver support for Intel Skylake devices
- Lots of rsnd cleanup and enhancements
- A few DAPM fixes and cleanups
- A large number of cleanups in various drivers (conversion and
standardized to regmap, component) mostly by Lars-Peter and Axel
HD-audio:
- Extended HD-audio core for Intel Skylake controller support
- Quirks for Dell headsets, Alienware 15
- Clean up of pin-based quirk tables for Realtek codecs
- ELD notifier implenetation for Intel HDMI/DP
USB-audio:
- Refactor runtime PM code to make lockdep happier
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=/sXs
-----END PGP SIGNATURE-----
Merge tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"There are little changes in core part, but lots of development are
found in drivers, especially ASoC. The diffstat shows regmap-related
changes for a slight API additions / changes, and that's all.
Looking at the code size statistics, the most significant addition is
for Intel Skylake. (Note that SKL support is still underway, the
codec driver is missing.) Also STI controller driver is a major
addition as well as a few new codec drivers.
In HD-audio side, there are fewer changes than the past. The
noticeable change is the support of ELD notification from i915
graphics driver. Thus this pull request carries a few changes in
drm/i915.
Other than that, USB-audio got a rewrite of runtime PM code. It was
initiated by lockdep warning, but resulted in a good cleanup in the
end.
Below are the highlights:
Common:
- Factoring out of AC'97 reset code from ASoC into the core helper
- A few regmap API extensions (in case it's not pulled yet)
ASoC:
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650
- Initial driver support for Intel Skylake devices
- Lots of rsnd cleanup and enhancements
- A few DAPM fixes and cleanups
- A large number of cleanups in various drivers (conversion and
standardized to regmap, component) mostly by Lars-Peter and Axel
HD-audio:
- Extended HD-audio core for Intel Skylake controller support
- Quirks for Dell headsets, Alienware 15
- Clean up of pin-based quirk tables for Realtek codecs
- ELD notifier implenetation for Intel HDMI/DP
USB-audio:
- Refactor runtime PM code to make lockdep happier"
* tag 'sound-4.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (411 commits)
drm/i915: Add locks around audio component bind/unbind
drm/i915: Drop port_mst_index parameter from pin/eld callback
ALSA: hda - Fix missing inline for dummy snd_hdac_set_codec_wakeup()
ALSA: hda - Wake the codec up on pin/ELD notify events
ALSA: hda - allow codecs to access the i915 pin/ELD callback
drm/i915: Call audio pin/ELD notify function
drm/i915: Add audio pin sense / ELD callback
ASoC: zx296702-i2s: Fix resource leak when unload module
ASoC: sti_uniperif: Ensure component is unregistered when unload module
ASoC: au1x: psc-i2s: Convert to use devm_ioremap_resource
ASoC: sh: dma-sh7760: Convert to devm_snd_soc_register_platform
ASoC: spear_pcm: Use devm_snd_dmaengine_pcm_register to fix resource leak
ALSA: fireworks/bebob/dice/oxfw: fix substreams counting at vmalloc failure
ASoC: Clean up docbook warnings
ASoC: txx9: Convert to devm_snd_soc_register_platform
ASoC: pxa: Convert to devm_snd_soc_register_platform
ASoC: nuc900: Convert to devm_snd_soc_register_platform
ASoC: blackfin: Convert to devm_snd_soc_register_platform
ASoC: au1x: Convert to devm_snd_soc_register_platform
ASoC: qcom: Constify asoc_qcom_lpass_cpu_dai_ops
...
We've got bug reports showing the old systemd-logind (at least
system-210) aborting unexpectedly, and this turned out to be because
of an invalid error code from close() call to evdev devices. close()
is supposed to return only either EINTR or EBADFD, while the device
returned ENODEV. logind was overreacting to it and decided to kill
itself when an unexpected error code was received. What a tragedy.
The bad error code comes from flush fops, and actually evdev_flush()
returns ENODEV when device is disconnected or client's access to it is
revoked. But in these cases the fact that flush did not actually happen is
not an error, but rather normal behavior. For non-disconnected devices
result of flush is also not that interesting as there is no potential of
data loss and even if it fails application has no way of handling the
error. Because of that we are better off always returning success from
evdev_flush().
Also returning EINTR from flush()/close() is discouraged (as it is not
clear how application should handle this error), so let's stop taking
evdev->mutex interruptibly.
Bugzilla: http://bugzilla.suse.com/show_bug.cgi?id=939834
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The 23 inch device found in Chrome project buddy requires 9.2~10.5 seconds
to complete calibration. Let's increase calibration timeout to 12 seconds
to give the device enough time.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These platform drivers have a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull MIPS updates from Ralf Baechle:
"This is the main pull request for 4.3 for MIPS. Here's the summary:
Three fixes that didn't make 4.2-stable:
- a -Os build might compile the kernel using the MIPS16 instruction
set but the R2 optimized inline functions in <uapi/asm/swab.h> are
implemented using 32-bit wide instructions which is invalid.
- a build error in pgtable-bits.h for a particular kernel
configuration.
- accessing registers of the CM GCR might have been compiled to use
64 bit accesses but these registers are onl 32 bit wide.
And also a few new bits:
- move the ATH79 GPIO driver to drivers/gpio
- the definition of IRQCHIP_DECLARE has moved to linux/irqchip.h,
change ATH79 accordingly.
- fix definition of pgprot_writecombine
- add an implementation of dma_map_ops.mmap
- fix alignment of quiet build output for vmlinuz link
- BCM47xx: Use kmemdup rather than duplicating its implementation
- Netlogic: Fix 0x0x prefixes of constants.
- merge Bjorn Helgaas' series to remove most of the weak keywords
from function declarations.
- CP0 and CP1 registers are best considered treated as unsigned
values to avoid large values from becoming negative values.
- improve support for the MIPS GIC timer.
- enable common clock framework for Malta and SEAD3.
- a number of improvments and fixes to dump_tlb().
- document the MIPS TLB dump functionality in Magic SysRq.
- Cavium Octeon CN68XX improvments.
- NetLogic improvments.
- irq: Use access helper irq_data_get_affinity_mask.
- handle MSA unaligned accesses.
- a number of R6-related math-emu fixes.
- support for I6400.
- improvments to MSA support.
- add uprobes support.
- move from deprecated __initcall to arch_initcall.
- remove finish_arch_switch().
- IRQ cleanups by Thomas Gleixner.
- migrate to new 'set-state' interface.
- random small cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (148 commits)
MIPS: UAPI: Fix unrecognized opcode WSBH/DSBH/DSHD when using MIPS16.
MIPS: Fix alignment of quiet build output for vmlinuz link
MIPS: math-emu: Remove unused handle_dsemul function declaration
MIPS: math-emu: Add support for the MIPS R6 MAX{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MIN{, A} FPU instruction
MIPS: math-emu: Add support for the MIPS R6 CLASS FPU instruction
MIPS: math-emu: Add support for the MIPS R6 RINT FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MSUBF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 MADDF FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELNEZ FPU instruction
MIPS: math-emu: Add support for the MIPS R6 SELEQZ FPU instruction
MIPS: math-emu: Add support for the CMP.condn.fmt R6 instruction
MIPS: inst.h: Add new MIPS R6 FPU opcodes
MIPS: Octeon: Fix management port MII address on Kontron S1901
MIPS: BCM47xx: Use kmemdup rather than duplicating its implementation
STAGING: Octeon: Use common helpers for determining interface and port
MIPS: Octeon: Support interfaces 4 and 5
MIPS: Octeon: Set up 1:1 mapping between CN68XX PKO queues and ports
MIPS: Octeon: Initialize CN68XX PKO
STAGING: Octeon: Support CN68XX style WQE
...
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luis@debethencourt.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The drivers have a I2C device ID table that is used to create the module
aliases and also "cyttsp" and "cyttsp4" are not supported I2C device IDs
so these module aliases are never used.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This ACPI ID present in the DSDT of the ASUS E202SA laptop.
Signed-off-by: João Paulo Rechi Vita <jprvita@endlessm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When driver is in IAP mode ic_type query may return 0xff. However
iap_version will always be valid, so let's use it to determine parameters
of the firmware that the controller is supposed to accept.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently CONFIG_ARCH_HAVE_CUSTOM_GPIO_H is defined for all MIPS
machines, and each machine type provides its own gpio.h. However
only a handful really implement the GPIO API, most just forward
everythings to gpiolib.
The Alchemy machine is notable as it provides a system to allow
implementing the GPIO API at the board level. But it is not used by
any board currently supported, so it can also be removed.
For most machine types we can just remove the custom gpio.h, as well
as the custom wrappers if some exists. Some of the code found in
the wrappers must be moved to the respective GPIO driver.
A few more fixes are need in some drivers as they rely on linux/gpio.h
to provides some machine specific definitions, or used asm/gpio.h
instead of linux/gpio.h for the gpio API.
Signed-off-by: Alban Bedel <albeu@free.fr>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-mips@linux-mips.org
Cc: Hauke Mehrtens <hauke@hauke-m.de>
Cc: Rafał Miłecki <zajec5@gmail.com>
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Manuel Lauss <manuel.lauss@gmail.com>
Cc: Joe Perches <joe@perches.com>
Cc: Daniel Walter <dwalter@google.com>
Cc: Sergey Ryazanov <ryazanov.s.a@gmail.com>
Cc: Huacai Chen <chenhc@lemote.com>
Cc: James Hartley <james.hartley@imgtec.com>
Cc: Andrew Bresticker <abrestic@chromium.org>
Cc: Paul Burton <paul.burton@imgtec.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Wolfram Sang <wsa@the-dreams.de>
Cc: Randy Dunlap <rdunlap@infradead.org>
Cc: Varka Bhadram <varkabhadram@gmail.com>
Cc: Masanari Iida <standby24x7@gmail.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Michael Buesch <m@bues.ch>
Cc: abdoulaye berthe <berthe.ab@gmail.com>
Cc: linux-kernel@vger.kernel.org
Cc: linux-ide@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Cc: netdev@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/10828/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
New or improved SoC support:
- Addition of support for Atmel's SAMA5D2 SoC
- Addition of Freescale i.MX6UL
- Improved support of TI's DM814x platform
- Misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch are
also here (acked by appropriate maintainers):
- Power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- Clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=8T5Z
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Olof Johansson:
"New or improved SoC support:
- add support for Atmel's SAMA5D2 SoC
- add support for Freescale i.MX6UL
- improved support for TI's DM814x platform
- misc fixes and improvements for RockChip platforms
- Marvell MVEBU suspend/resume support
A few driver changes that ideally would belong in the drivers branch
are also here (acked by appropriate maintainers):
- power key input driver for Freescale platforms (svns)
- RTC driver updates for Freescale platforms (svns/mxc)
- clk fixes for TI DM814/816X
+ a bunch of other changes for various platforms"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: rockchip: pm: Fix PTR_ERR() argument
ARM: imx: mach-imx6ul: Fix allmodconfig build
clk: ti: fix for definition movement
ARM: uniphier: drop v7_invalidate_l1 call at secondary entry
memory: kill off set_irq_flags usage
rtc: snvs: select option REGMAP_MMIO
ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE
ARM: BCM: Enable ARM erratum 798181 for BRCMSTB
ARM: OMAP2+: Fix power domain operations regression caused by 81xx
ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend
ARM: rockchip: set correct stabilization thresholds in suspend
ARM: rockchip: rename osc_switch_to_32k variable
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback
soc: mediatek: Fix SCPSYS compilation
ARM: at91/soc: add basic support for new sama5d2 SoC
...
Pull x86 asm changes from Ingo Molnar:
"The biggest changes in this cycle were:
- Revamp, simplify (and in some cases fix) Time Stamp Counter (TSC)
primitives. (Andy Lutomirski)
- Add new, comprehensible entry and exit handlers written in C.
(Andy Lutomirski)
- vm86 mode cleanups and fixes. (Brian Gerst)
- 32-bit compat code cleanups. (Brian Gerst)
The amount of simplification in low level assembly code is already
palpable:
arch/x86/entry/entry_32.S | 130 +----
arch/x86/entry/entry_64.S | 197 ++-----
but more simplifications are planned.
There's also the usual laudry mix of low level changes - see the
changelog for details"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (83 commits)
x86/asm: Drop repeated macro of X86_EFLAGS_AC definition
x86/asm/msr: Make wrmsrl() a function
x86/asm/delay: Introduce an MWAITX-based delay with a configurable timer
x86/asm: Add MONITORX/MWAITX instruction support
x86/traps: Weaken context tracking entry assertions
x86/asm/tsc: Add rdtscll() merge helper
selftests/x86: Add syscall_nt selftest
selftests/x86: Disable sigreturn_64
x86/vdso: Emit a GNU hash
x86/entry: Remove do_notify_resume(), syscall_trace_leave(), and their TIF masks
x86/entry/32: Migrate to C exit path
x86/entry/32: Remove 32-bit syscall audit optimizations
x86/vm86: Rename vm86->v86flags and v86mask
x86/vm86: Rename vm86->vm86_info to user_vm86
x86/vm86: Clean up vm86.h includes
x86/vm86: Move the vm86 IRQ definitions to vm86.h
x86/vm86: Use the normal pt_regs area for vm86
x86/vm86: Eliminate 'struct kernel_vm86_struct'
x86/vm86: Move fields from 'struct kernel_vm86_struct' to 'struct vm86'
x86/vm86: Move vm86 fields out of 'thread_struct'
...
Not many updates to the core here, but an awful lot of driver updates
this time round:
- Factoring out of AC'97 reset code into the core
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers.
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650.
- Initial driver support for Intel Skylake devices.
- A large number of cleanups for Lars-Peter Clausen and Axel Lin.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJV4xxpAAoJECTWi3JdVIfQjuUH/3xuZSROdiVUit9zWHepebqR
4e9bgu9vN9RfFZ3BqYC/0TIv8PwtwvDFu3xJoCxy52wcXWuz/H4itH9xh21EiL9l
4s14Sfkj8BA332aQMXKMFBtpB5S1feMFhBSATihfXlfLCLby9Gm0GDoLiiDklX47
svysCy9G9CmCSDufZ6TcO58PUJvjrQaI0SY5oAG2JnHW7XmnG6a7s5gJR4bu/FXs
oJfkLbpfIl03JdJ/q1IoTm0UUyRaTx7cWKoOtp8icoza8cfnsUG8uoCAvbYcG3Li
/1JtZrVjZPM+ZpM0+5gl9mhRpj8zJksDgTPT2mlzWfsgJiuo48w9xqlqItvJjG8=
=92/y
-----END PGP SIGNATURE-----
Merge tag 'asoc-v4.2-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v4.3
Not many updates to the core here, but an awful lot of driver updates
this time round:
- Factoring out of AC'97 reset code into the core
- New drivers for Cirrus CS4349, GTM601, InvenSense ICS43432, Realtek
RT298 and ST STI controllers.
- Machine drivers for Rockchip systems with MAX98090 and RT5645 and
RT5650.
- Initial driver support for Intel Skylake devices.
- A large number of cleanups for Lars-Peter Clausen and Axel Lin.
The driver is a platform driver and not a I2C driver so its modalias
should be exported with MODULE_DEVICE_TABLE(platform,...) instead of
MODULE_DEVICE_TABLE(i2c,...).
Also, remove the unnecessary MODULE_ALIAS("platform:max8997-haptic")
now that the correct module alias is created.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Search for "vaildpage_count" and replace with "validpage_count".
Signed-off-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
There are trackpoint devices that fail to respond to the PS2 command
PSMOUSE_CMD_GETID if immediately queried after the parent device is
deactivated. Add a small delay for the hardware to get in a sane state
before sending any PS2 commands.
One example of such a system is:
Lenovo ThinkPad X120e, model 30515QG
synaptics: Touchpad model: 1, fw: 8.0, id: 0x1e2b1, caps: 0xd001a3/0x940300/0x121c00, board id: 1811, fw id: 797391
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Bit 2 of the mode byte has dual meaning: it can disable reporting of
gestures when touchpad works in Relative mode or normal Absolute mode,
or it can enable so called Extended W-Mode when touchpad uses enhanced
Absolute mode (W-mode). The extended W-Mode confuses our driver and
causes missing button presses on some Thinkpads (x250, T450s), so let's
make sure we do not enable it.
Also, according to the spec W mode "... bit is defined only in Absolute
mode on pads whose capExtended capability bit is set. In Relative mode and
in TouchPads without this capability, the bit is reserved and should be
left at 0.", so let's make sure we respect this requirement as well.
Reported-by: Nick Bowler <nbowler@draconx.ca>
Suggested-by: Gabor Balla <gaborwho@gmail.com>
Tested-by: Gabor Balla <gaborwho@gmail.com>
Tested-by: Nick Bowler <nbowler@draconx.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Enable ELAN0100 touchpad driver, found on a Asus X205TA laptop, to
gai 2,3 fingers tap and 2 fingers scroll.
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Reviewed-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When trying to disable a key that is not supported by the device we should
report error, not do nothing and report success:
root@yocto:/sys/devices/soc0/gpio-keys# cat keys
114-116
root@yocto:/sys/devices/soc0/gpio-keys# echo 77 > keys
root@yocto:/sys/devices/soc0/gpio-keys#
We want 'echo 77 > keys' to report an error, but silence to give us an
illusion that all is 'ok'.
Signed-off-by: Peng Fan <van.freenix@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Propagate error code on failure, or upper layers will be confused by
returned 0 (success) code.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fix from Dmitry Torokhov:
"A small fixup to gpio_keys_polled driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: gpio_keys_polled - request GPIO pin as input.
Convert the ac97_bus from legacy suspend/resume callbacks to dev_pm_ops.
Since there isn't anything special to do at the bus level the bus driver
does not have to implement any callbacks. The device driver core will
automatically pick up and execute the device's PM ops.
As there is only a single AC'97 driver implementing suspend and resume,
update both the core and driver at the same time to avoid unnecessary code
churn.
While we are at it also drop the ifdefs around the suspend/resume functions
to increase compile test coverage.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I have a static checker that complains when we check for an upper bound
but don't have a corresponding check for a lower bound. With this code,
the upper bound check seems not really required, so it is not a bug to
leave the lower bound check out as well. But let's silence the warning
by making these variables unsigned.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
GPIOF_IN flag was lost in:
Commit 633a21d80b4a("input: gpio_keys_polled: Add support for GPIO
descriptors").
Without this flag, legacy code path (for non-descriptor GPIO declarations)
would configure GPIO as output (0 meaning GPIOF_DIR_OUT | GPIOF_INIT_LOW).
Cc: stable@vger.kernel.org
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The ChromeOS EC keyboard driver config depends on CROS_EC_PROTO but
MFD_CROS_EC selects CROS_EC_PROTO instead. Mixing select and depends
on is bad practice as it may lead to circular Kconfig dependencies.
Since the platform device that is matched with the keyboard driver
is registered by the ChromeOS EC mfd driver, KEYBOARD_CROS_EC really
should depend on MFD_CROS_EC. And because this config option selects
CROS_EC_PROTO, that dependency is met as well. So make the driver
to depend on MFD_CROS_EC instead of CROS_EC_PROTO.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
- Add i.MX6 Ultralite SoC support, which is the newest addition to
i.MX6 family. It integrates a single Cortex-A7 core and a power
management module that reduces the complexity of external power
supply and simplifies power sequencing.
- Change SNVS RTC driver to use syscon interface for register access,
and add SNVS power key driver support.
- Add a second clock for mxc rtc driver, and support device tree probe
for the driver.
- Add FEC MAC reference clock and phy fixup initialization for i.MX6UL
platform.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVyg8nAAoJEFBXWFqHsHzOQC8H/iY+cdNfAWIxYmt2CeF607su
fLaycUSUPqPAERUTcHpjKyiKkRg2NWV7vFVWCkKaQ3RZ+IW6xNntkqMxzocS1sh2
+70Ckp+B0orGuo96PkEXua9fNPf8/yaGiDhuJpK966VRRSSXRD15uOuqHAJ2Jz/v
HEnEm3KANSSYS1heEJRqiiCsqhADRWl2RzgfV327aXtScP9zXlbJGlEc/jUVAY65
wbqjsXdySeS3rECNMAYXnPU7IlK4NkRqrOi1JmTJCBlXqV2b6dBfjgIu9jOa91UG
yRj7IEBJemqT4Ap1ee2NR3H1lDngt2JKg9XqRDL3j9alYvhAWGvhSY2UH2iPrFg=
=emep
-----END PGP SIGNATURE-----
Merge tag 'imx-soc-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into next/soc
The i.MX SoC changes for 4.3:
- Add i.MX6 Ultralite SoC support, which is the newest addition to
i.MX6 family. It integrates a single Cortex-A7 core and a power
management module that reduces the complexity of external power
supply and simplifies power sequencing.
- Change SNVS RTC driver to use syscon interface for register access,
and add SNVS power key driver support.
- Add a second clock for mxc rtc driver, and support device tree probe
for the driver.
- Add FEC MAC reference clock and phy fixup initialization for i.MX6UL
platform.
* tag 'imx-soc-4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
rtc: snvs: select option REGMAP_MMIO
ARM: imx6ul: add fec MAC refrence clock and phy fixup init
ARM: imx6ul: add fec bits to GPR syscon definition
rtc: mxc: add support of device tree
dt-binding: document the binding for mxc rtc
rtc: mxc: use a second rtc clock
input: snvs_pwrkey: use "wakeup-source" as deivce tree property name
Document: devicetree: input: imx: i.mx snvs power device tree bindings
input: keyboard: imx: add snvs power key driver
Document: dt: fsl: snvs: change support syscon
rtc: snvs: use syscon to access register
ARM: imx: add low-level debug support for i.mx6ul
ARM: imx: add i.mx6ul msl support
Signed-off-by: Olof Johansson <olof@lixom.net>
Several cap11xx variants have LEDs that be can be controlled; let's plug
the driver into the LED subsystem.
Signed-off-by: Matt Ranostay <mranostay@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Flags are now mandatory for devm_gpiod_get(). So let's use proper flag
to configure gpio for output instead of doing this by hand.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
[Dmitry: GPIOD_ASIS -> GPIOD_OUT_LOW]
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem fixes from Dmitry Torokhov:
"Just small ALPS and Elan touchpads, and other driver fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elantech - add special check for fw_version 0x470f01 touchpad
Input: twl4030-vibra - fix ERROR: Bad of_node_put() warning
Input: alps - only Dell laptops have separate button bits for v2 dualpoint sticks
Input: axp20x-pek - add module alias
Input: turbografx - fix potential out of bound access
It takes a bit of time to go through controller power up sequence and
initialization. To not stall the overall boot progress let's probe the
controller asynchronously, given that userspace is usually prepared for
hot-plugging of input devices and thus does not rely on particular
ordering.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It takes a bit of time to go through controller power up sequence and
initialization. To not stall the overall boot progress let's probe the
controller asynchronously, given that userspace is usually prepared for
hot-plugging of input devices and thus does not rely on particular
ordering.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Elan touchscreen controllers use two power supplies, vcc33 and vccio,
and we need to enable them before trying to access the device. On X86
firmware usually does this, but on ARM it is usually left to the kernel.
Signed-off-by: Dmitry Torokhov <dtor@chromium.org>
Reviewed-by: Benson Leung <bleung@chromium.org>
Reviewed-by: Scott Liu <scott.liu@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do not emit EV_SYN/SYN_REPORT on suspend if there were no keys that are
still pressed as we are suspending the device (and in all other cases when
input core is forcibly releasing keys via input_dev_release_keys() call).
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It is no need to check the packet[0] for sanity check when doing
elantech_packet_check_v4() function for fw_version = 0x470f01 touchpad.
Signed-off by: Duson Lin <dusonlin@emc.com.tw>
Reviewed-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The max77693 haptic driver supports Maxim 77843 device so remove the
max77843 driver.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The Maxim 77843 haptic driver differs from 77693 by:
1. Setting the bias.
2. Different configuration register.
3. Not enabling the low-sys DAC.
4. Using same regmap for PMIC and haptic blocks.
Incorporate all differences into max77693 haptic driver so both devices
can be supported.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Prepare the driver for supporting two devices: Maxim 77693 and 77843:
1. Add table of device ids and store current device type for later
usage.
2. Differentiate the haptic device configuration.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Storing a predefined PWM divisor in state container structure is
meaningless. The field, after initialization, is only read so this only
obfuscates the code. Remove the field and use directly enum value.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This patch fix spelling typo inv various part of sources.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.com>
If the device is in idle mode and is in the middle of a scan it may not
have a chance to react to the reset and then IAP commands within required
time interval and firmware update may fail. Let's bring the device out of
idle mode before attempting to reset it so that the scan period is smaller
and thus it can react to the command quicker.
Signed-off-by: James Chen <james.chen@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This indicates the device coordinates should be directly mapped to screen.
This is valid since scaling/flipping/rotation should be done by configuring
the MXT device.
It also flags to Android using INPUT_PROP_DIRECT that the device should be
treated as a touch screen by default, and removes the necessity for a
default IDC file.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The CHG/interrupt line is momentarily set (approximately 100 ms) as an
input after power-up or reset for diagnostic purposes. This may cause
spurious interrupts, so disable interrupt handler during this period.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use function rather than loop, define np to reduce wrapping.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_dev may be NULL if mxt_initialize_input_device fails. But pm ops is
still available and suspend/resume assume
input_dev is not NULL. To fix this issue, we add a check if (!input_dev).
Signed-off-by: Pan Xinhui <xinhuix.pan@intel.com>
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Many of these values are out of date and they aren't used in the driver
- all they do is increase the size of the kernel source.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The hardcoded 0x83 CTRL setting overrides other settings in that byte,
enabling extra reporting that may not be useful on a particular platform.
Implement improved suspend mechanism via deep sleep. By writing zero to
both the active and idle cycle times the maXTouch device can be put into a
deep sleep mode, using minimal power. It is necessary to issue a calibrate
command after the chip has spent any time in deep sleep, however a soft
reset is unnecessary.
Use the old method on Chromebook Pixel via platform data option.
This patch also deals with the situation where the power configuration is
zero on probe, which would mean that the device never wakes up to execute
commands.
After a config download, the T7 power configuration may have changed so it
is necessary to re-read it.
Signed-off-by: Nick Dyer <nick.dyer@itdev.co.uk>
Acked-by: Benson Leung <bleung@chromium.org>
Acked-by: Yufeng Shen <miletus@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The GPIO subsystem provides dummy GPIO consumer functions if GPIOLIB is
not enabled. Hence drivers that depend on GPIOLIB, but use GPIO consumer
functionality only, can still be compiled if GPIOLIB is not enabled.
Relax the dependency on GPIOLIB if COMPILE_TEST is enabled, where
appropriate.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
It turns out that only Dell laptops have the separate button bits for
v2 dualpoint sticks and that commit 92bac83dd7 ("Input: alps - non
interleaved V2 dualpoint has separate stick button bits") causes
regressions on Toshiba laptops.
This commit adds a check for Dell laptops to the code for handling these
extra button bits, fixing this regression.
This patch has been tested on a Dell Latitude D620 to make sure that it
does not reintroduce the original problem.
Reported-and-tested-by: Douglas Christman <douglaschristman@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add a proper module alias so the driver can be autoloaded when the
parent axp20x mfd driver registers its cells.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Patch 17dd3f0f7a: "[PATCH] drivers/input/joystick: convert to dynamic
input_dev allocation" from Sep 15, 2005, leads to the following static
checker warning:
drivers/input/joystick/turbografx.c:235 tgfx_probe()
error: buffer overflow 'tgfx_buttons' 5 <= 5
drivers/input/joystick/turbografx.c
195 for (i = 0; i < n_devs; i++) {
196 if (n_buttons[i] < 1)
197 continue;
198
199 if (n_buttons[i] > 6) {
^^^^^^^^^^^^^^^^
Possibly off by one. >= 6.
Let's change the upper value to ARRAY_SIZE(tgfx_buttons) to ensure we do
not reach past the end of the array.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for hardware which uses an I2C Serializer / Deserializer
(SerDes) to communicate with the zFroce touch driver. In this case the
SerDes will be configured as an interrupt controller and the zForce driver
will have no access to poll the GPIO line.
To support this, we add two dedicated new GPIOs in the device tree:
reset-gpios and irq-gpios, with the irq-gpios being optional.
To not break the existing device trees, the index based 'gpios' entries
are still supported, but marked as deprecated.
With this, if the interrupt GPIO is available, either via the old or new
device tree style, the while loop will read and handle the packets as long
as the GPIO indicates that the interrupt is asserted (existing, unchanged
driver behavior).
If the interrupt GPIO isn't available, i.e. not configured via the new
device tree style, we are falling back to one read per ISR invocation
(new behavior to support the SerDes).
Note that the gpiod functions help to handle the optional GPIO:
devm_gpiod_get_index_optional() will return NULL in case the interrupt
GPIO isn't available. And gpiod_get_value_cansleep() does cover this, too,
by returning 0 in this case.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Reviewed-by: Heiko Stuebner <heiko.stuebner@bq.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The thermal code uses int, long and unsigned long for temperatures
in different places.
Using an unsigned type limits the thermal framework to positive
temperatures without need. Also several drivers currently will report
temperatures near UINT_MAX for temperatures below 0°C. This will probably
immediately shut the machine down due to overtemperature if started below
0°C.
'long' is 64bit on several architectures. This is not needed since INT_MAX °mC
is above the melting point of all known materials.
Consistently use a plain 'int' for temperatures throughout the thermal code and
the drivers. This only changes the places in the drivers where the temperature
is passed around as pointer, when drivers internally use another type this is
not changed.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Reviewed-by: Darren Hart <dvhart@linux.intel.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Peter Feuerer <peter@piie.net>
Cc: Punit Agrawal <punit.agrawal@arm.com>
Cc: Zhang Rui <rui.zhang@intel.com>
Cc: Eduardo Valentin <edubezval@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Jean Delvare <jdelvare@suse.de>
Cc: Peter Feuerer <peter@piie.net>
Cc: Heiko Stuebner <heiko@sntech.de>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: linux-acpi@vger.kernel.org
Cc: platform-driver-x86@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Cc: linux-samsung-soc@vger.kernel.org
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: lm-sensors@lm-sensors.org
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Avoid the driver generate warning message when the cyapa driver working
with the old Gen5 trackpad device which does not support the proximity
function. Those old Gen5 trackpad device all have the platform version
less than 2.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add device tree support for Cypress trackpad devices.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We need to power up the chip before we can initialize it.
On systems that delegate task of powering up regulators to firmware we
assume that we'll be simply given a dummy regulator.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So technically there's no need for a driver to export
the OF table since currently it's not used.
In fact, the I2C device ID table is mandatory for I2C drivers since
a i2c_device_id is passed to the driver's probe function even if the
I2C core used the OF table to match the driver.
And since the I2C core uses different tables, OF-only drivers needs to
have duplicated data that has to be kept in sync and also the dev node
compatible manufacturer prefix is stripped when reporting the MODALIAS.
To avoid the above, the I2C core behavior may be changed in the future
to not require an I2C device table for OF-only drivers and report the
OF module alias. So, it's better to also export the OF table to prevent
breaking module autoloading if that happens.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The I2C core always reports the MODALIAS uevent as "i2c:<client name"
regardless if the driver was matched using the I2C id_table or the
of_match_table. So the driver needs to export the I2C table and this
be built into the module or udev won't have the necessary information
to auto load the correct module when the device is added.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"The main change is support for keyboards and touchpads found in 2015
editions of Macbooks"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: zforce - don't overwrite the stack"
Input: bcm5974 - add support for the 2015 Macbook Pro
HID: apple: Add support for the 2015 Macbook Pro
Input: bcm5974 - prepare for a new trackpad generation
Input: synaptics - dump ext10 capabilities as well
This reverts commit 7d01cd261c because
with given FRAME_MAXSIZE of 257 the check will never trigger and it
causes warnings from GCC (with -Wtype-limits). Also the check was
incorrect as it was not accounting for the already read 2 bytes of data
stored in the buffer.
The GPIOD API can be used from boardcode, so that the DT check can be
removed. To avoid breaking existing boardcode, _optional() variant has been
chosen. For completely removing the DT check, the regulator has also been
made optional, so that it could be supplied from boardcode.
As a side-effect the patch fixes the after-probe reset GPIO state, so that
the device is not kept in reset state.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Using dev_*_drvdata() instead of spi_*_drvdata() reduces lines of code and
prepares the driver for possible tsc2004 support, which is i2c based.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Convert driver so that it uses regmap instead of directly using
spi_transfer for all register accesses.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Replace spaces with tab, so that the tsc2005 Kconfig entry matches the
other entries in drivers/input/touchscreen/Kconfig.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Improve defines for first control byte by removing 0x00 prefix (the defines
are for 8 bit values and not for 16 bit values) and expose register
structure by exposing the shift.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add support for the MacBookPro12,1 model. This patch needs to be
applied together with the accompanied HID patch, as usual.
Tested-by: John Horan <knasher@gmail.com>
Tested-by: Jochen Radmacher <jradmacher@gmx.de>
Tested-by: Yang Hongyang <burnef@gmail.com>
Tested-by: Yen-Chin, Lee <coldnew.tw@gmail.com>
Tested-by: George Hilios <ghilios@gmail.com>
Tested-by: Janez Urevc <janez@janezurevc.name>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With the advent of the Macbook Pro 12, we see a new generation of
trackpads, capable of force sensoring and haptic feedback.
This patch prepares for the new device by adding configuration data
for the code paths that would otherwise look different.
Tested-by: John Horan <knasher@gmail.com>
Tested-by: Jochen Radmacher <jradmacher@gmx.de>
Tested-by: Yang Hongyang <burnef@gmail.com>
Tested-by: Yen-Chin, Lee <coldnew.tw@gmail.com>
Tested-by: George Hilios <ghilios@gmail.com>
Tested-by: Janez Urevc <janez@janezurevc.name>
Signed-off-by: Henrik Rydberg <rydberg@bitmath.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make extended capabilities obtained through $10 query also available in
touchpad identification.
Signed-off-by: Jiri Kosina <jkosina@suse.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fix for the warnings/oops when handling HID devices with "unnamed"
LEDs and couple of other driver fixups""
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: goodix - fix touch coordinates on WinBook TW100 and TW700
Input: LEDs - skip unnamed LEDs
Input: usbtouchscreen - avoid unresponsive TSC-30 touch screen
Input: elantech - force resolution of 31 u/mm
Input: zforce - don't overwrite the stack
The touchscreen on the WinBook TW100 and TW700 don't match the default
display, with 0,0 touches being reported when touching at the bottom
right of the screen.
1280,800 0,800
+-------------+
| |
| |
| |
+-------------+
1280,0 0,0
It's unfortunately impossible to detect this problem with data from the
DSDT, or other auxiliary metadata, so fallback to quirking this specific
model of tablet instead.
Signed-off-by: Bastien Nocera <hadess@hadess.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Devices may declare more LEDs than what is known to input-leds
(HID does this for some devices). Instead of showing ugly warnings
on connect and, even worse, oopsing on disconnect, let's simply
ignore LEDs that are not known to us.
Reported-and-tested-by: Vlastimil Babka <vbabka@suse.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add CYTP0002 to the list of ACPI HIDs recognized by the driver.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the the runtime suspend power management not working issue when system
starts up and before user touches the trackpad device.
TEST=test on Chromebook.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Gen5 and Gen6 trackpad devices are able to detect and report object
proximity data/events, add this function support in the cyapa driver
through the ABS_DISTANCE event.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on the cyapa core, add support for basic functionality of the gen6
trackpad devices. The driver can automatically determine what protocol
(gen3, gen5, or gen6) should be used with the attached trackpad device.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change 'gen5' to 'pip' for all macros, variables and functions that are
shared between gen5 and gen6 modules to make naming more clear and
readable.
Also fix a few spelling errors.
Signed-off-by: Dudley Du <dudl@cypress.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch the driver to use managed resources, this will simplify
error handling and driver unbinding logic.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Acked-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wakeup property of device is not Linux-specific, it describes intended
system behavior regardless of the OS being used. Therefore let's drop
"linux," prefix, and, while at it, use the same name as I2C bus does:
"wakeup-source".
We keep parsing old name to keep compatibility with old DTSes.
Cc: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On pm8xxx PMICs, shutdown and restart are signaled to the PMIC via a pin
called PS_HOLD. When this pin goes low, the PMIC performs a configurable
power sequence. Add a .shutdown hook so that we can properly configure this
power sequence for shutdown or restart depending on the system state.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@sonymobile.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This patch fixes a problem in the usbtouchscreen driver for DMC TSC-30
touch screen. Due to a missing delay between the RESET and SET_RATE
commands, the touch screen may become unresponsive during system startup or
driver loading.
According to the DMC documentation, a delay is needed after the RESET
command to allow the chip to complete its internal initialization. As this
delay is not guaranteed, we had a system where the touch screen
occasionally did not send any touch data. There was no other indication of
the problem.
The patch fixes the problem by adding a 150ms delay between the RESET and
SET_RATE commands.
Cc: stable@vger.kernel.org
Suggested-by: Jakob Mustafa <jakob.mustafa@bytecmed.com>
Signed-off-by: Bernhard Bender <bernhard.bender@bytecmed.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVrBp0AAoJEHm+PkMAQRiGADsH/iCVjA1x+a19xpeuHNJcjcQR
Lin8td8zdUxereBNQOFjnkhCmKtzLODXGkQdYFaWZx8mbEQ93wC+nPV8O+LsqPbI
T/2MjJ78IjlNsoTyE4b1AhqpASsxrLZJNB+f9dd251f1BSAzKfRER0G46WxbOPN7
9HdzCMbtx03ZJkr9baE6alljxA43O5mpDzpotKIagfTMQr5h0ra16uXlmVXFjHRs
roNJsugwKxJPnVmLWWOM1JsAjRSMBAXQUQxhJJCMDOhgZZ5KR1z6L30ESeFTUhvh
WG/2MEfyVYXn91kV0N+AUCuOFHTv6uiaz3RaRVJFDSv3sPOh1WQ9tQHxyrBsqyY=
=MA/P
-----END PGP SIGNATURE-----
Merge tag 'v4.2-rc3' into next
Sync up with Linux 4.2-rc3 to bring in infrastructure (OF) pieces.
ELAN0600 seems to work just fine in mouse emulation mode through i2c-hid,
but to have full raw touch support we need to register it in elan_i2c.ko
Reported-and-tested-by: Alessio Treglia <alessio@debian.org>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Jiri Kosina <jkosina@suse.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Commit 2d53809594 ("Input: zforce_ts - convert to use the gpiod
interface") converted this driver to use the gpiod functions. These
functions take the active low property into account, so we don't have
to invert the result of gpiod_get_value_cansleep(). This has been
missed in that commit. Fix it.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of inventing a new property name, let's use "wakeup-source" to
be consistent with other driver and subsystem bindings.
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
i2c_driver does not need to set an owner because i2c_register_driver()
will set it.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Separate the functionality using sequences of register writes from the
functions that take register defaults. This change renames the arguments
in order to support the extension of reg_sequence to take an optional
delay to be applied after any given register in a sequence is written.
This avoids adding an int to all register defaults, which could
substantially increase memory usage for regmaps with large default tables.
This also updates all the clients of multi_reg_write/register_patch.
Signed-off-by: Nariman Poushin <nariman@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch to the same definition of state container as in MAX77693 drivers.
This will allow usage of one regulator driver in both devices: MAX77693
and MAX77843.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This prepares for merging some of the drivers between max77693 and
max77843 so the child MFD driver can be attached to any parent MFD main
driver.
Move the state container to common header file. Additionally add
consistent 'i2c' prefixes to its members (of 'struct i2c_client' type).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
All Elantech touchpads pre-v4 with dynamic resolution queries have a fixed
resolution of 800dpi -> 31.49 units/mm. Set this statically, so userspace
does not have to guess.
Signed-off-by: Peter Hutterer <peter.hutterer@who-t.net>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
If we get a corrupted packet with PAYLOAD_LENGTH > FRAME_MAXSIZE, we
will silently overwrite the stack.
Cc: stable@vger.kernel.org
Signed-off-by: Oleksij Rempel <external.Oleksij.Rempel@de.bosch.com>
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The legacy system PM support has long time ago been dropped from the
AMBA bus. Align to that by converting to the modern system PM
callbacks.
Fixes: 26825cfd90 (ARM: 7914/1: amba: Drop legacy PM support ...)
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
A big problem with the current i8042 debugging option is that it outputs
data going to and from the keyboard by default. As a result, many dmesg
logs uploaded by users will unintentionally contain sensitive information
such as their password, as such it's probably a good idea not to output
data coming from the keyboard unless specifically enabled by the user.
Signed-off-by: Stephen Chandler Paul <cpaul@redhat.com>
Reviewed-by: Andreas Mohr <andim2@users.sf.net>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
add snvs power key driver.
It work in imx chips after i.mx6sx
ON/OFF key used power on/off whole system.
This driver make it wakeup from suspend state when short press
ON/OFF key.
Long time press will trig SNVS power off chip without software
intervention.
Signed-off-by: Robin Gong <b38343@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The original wait time was 200ms which was enough for the firmware to
finish loading and boot. After that the firmware will perform
initialization and touch calibration, which will take about 1.1 second. The
touch calibration will change controller frequency to scan at the most
optimal frequency and during calibration/frequency switching process we may
run into i2c data errors. To avoid them we extend the sleep to 2500ms after
issuing the sw reset.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These attributes can be used to identify controllers present in the system.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch to using standard touchscreen device properties parsing module
instead of doing it by hand in the driver.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() will perform necessary settings for performing
multi-touch to single-touch emulation, we do not need to do that ourselves.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The controller has a RESET pin which is usually controlled over
a GPIO line. If such a GPIO is provided, perform a RESET
during probe.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We are using threaded interrupt handler and thus are allowed to sleep.
Let's switch over to gpiod_get_value_cansleep() so that we do not get
ugly warnings in case GPIO controller might sleep when accessing GPIO.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This allows uniform parsing on legacy, DT and ACPI systems.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's move driver's platform data definitions from include/linux/input/
into include/linux/platform_data/ so that it stays with the rest of
platform data definitions.
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's switch form OF to device properties so that common parsing code could
work not only on device tree but also on ACPI-based platforms.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The binding specification says that "touchscreen-size-x" and "-y" specify
horizontal and vertical resolution of the touchscreen and therefore maximum
absolute coordinates should be reduced by 1 since we are starting with 0.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Do issue warning about axis that is present in device tree but not specified
by the driver even in case of multi-touch axis as callers now tell us if they
expect multi-touch data or not.
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"A fix (revert) for a recent regression in Synaptics driver and a fix
for Elan i2c touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Revert "Input: synaptics - allocate 3 slots to keep stability in image sensors"
Input: elan_i2c - change the hover event from MT to ST
Use for_each_set_bit to check for set bits in bitmap
as it is more efficient and compact.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use for_each_set_bit to check for set bits in bitmap
as it is more efficient than checking individual bits.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use for_each_set_bit to check for set bits in bitmap as it is more
efficient than checking individual bits.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
These reg_default tables are not modified after initialized, so make them
const.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use the new GPIO descriptor interface to handle the zForce GPIOs.
This simplifies the code and allows transparently handle GPIO polarity, as
specified in device tree data.
Also switch to using gpio_{set|get}_value_cansleep() since none of the
callers is in atomic context and cansleep variant allows more GPIO
controllers to be used with the touchscreen.
Signed-off-by: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Despite it's name, sign_extend32() is used for 16 bit values aswell.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The firmware only reports hover condition while the very first contact is
approaching the surface; the hover is not reported for the subsequent
contacts. Therefore we should not be using ABS_MT_DISTANCE to report hover
but rather its single-touch counterpart ABS_DISTANCE.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that there is no paravirt TSC, the "native" is
inappropriate. The function does RDTSC, so give it the obvious
name: rdtsc().
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Link: http://lkml.kernel.org/r/fd43e16281991f096c1e4d21574d9e1402c62d39.1434501121.git.luto@kernel.org
[ Ported it to v4.2-rc1. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
It's unclear to me why this code exists in the first place.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: linux-input@vger.kernel.org
Link: http://lkml.kernel.org/r/9e058e72f4cf1f13c6483c1360b39c3d188a2c2a.1434501121.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This timing code is hideous, and this doesn't help. It gets rid
of one of the last users of rdtscl(), though.
Signed-off-by: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Huang Rui <ray.huang@amd.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: kvm ML <kvm@vger.kernel.org>
Cc: linux-input@vger.kernel.org
Link: http://lkml.kernel.org/r/90d19b3cea0e05ca6f333d1598daa38afb993260.1434501121.git.luto@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Pull second round of input updates from Dmitry Torokhov:
"A new driver for Weida wdt87xx touch controllers, and a bunch of
fixups for other drivers"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: wdt87xx_i2c - add a scaling factor for TOUCH_MAJOR event
Input: wdt87xx_i2c - remove stray newline in diagnostic message
Input: arc_ps2 - add HAS_IOMEM dependency
Input: wdt87xx_i2c - fix format warning
Input: improve parsing OF parameters for touchscreens
Input: edt-ft5x06 - mark as direct input device
Input: use for_each_set_bit() where appropriate
Input: add a driver for wdt87xx touchscreen controller
Input: axp20x-pek - fix reporting button state as inverted
Input: xpad - re-send LED command on present event
Input: xpad - set the LEDs properly on XBox Wireless controllers
Input: imx_keypad - check for clk_prepare_enable() error
Get the scaling factor when it reads the sys params. The width value will
multiple the factor and report the value in the TOUCH_MAJOR event.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Main excitement here is Peter Zijlstra's lockless rbtree optimization to
speed module address lookup. He found some abusers of the module lock
doing that too.
A little bit of parameter work here too; including Dan Streetman's breaking
up the big param mutex so writing a parameter can load another module (yeah,
really). Unfortunately that broke the usual suspects, !CONFIG_MODULES and
!CONFIG_SYSFS, so those fixes were appended too.
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tWPQ
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Main excitement here is Peter Zijlstra's lockless rbtree optimization
to speed module address lookup. He found some abusers of the module
lock doing that too.
A little bit of parameter work here too; including Dan Streetman's
breaking up the big param mutex so writing a parameter can load
another module (yeah, really). Unfortunately that broke the usual
suspects, !CONFIG_MODULES and !CONFIG_SYSFS, so those fixes were
appended too"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (26 commits)
modules: only use mod->param_lock if CONFIG_MODULES
param: fix module param locks when !CONFIG_SYSFS.
rcu: merge fix for Convert ACCESS_ONCE() to READ_ONCE() and WRITE_ONCE()
module: add per-module param_lock
module: make perm const
params: suppress unused variable error, warn once just in case code changes.
modules: clarify CONFIG_MODULE_COMPRESS help, suggest 'N'.
kernel/module.c: avoid ifdefs for sig_enforce declaration
kernel/workqueue.c: remove ifdefs over wq_power_efficient
kernel/params.c: export param_ops_bool_enable_only
kernel/params.c: generalize bool_enable_only
kernel/module.c: use generic module param operaters for sig_enforce
kernel/params: constify struct kernel_param_ops uses
sysfs: tightened sysfs permission checks
module: Rework module_addr_{min,max}
module: Use __module_address() for module_address_lookup()
module: Make the mod_tree stuff conditional on PERF_EVENTS || TRACING
module: Optimize __module_address() using a latched RB-tree
rbtree: Implement generic latch_tree
seqlock: Introduce raw_read_seqcount_latch()
...
Fix this compile error:
drivers/built-in.o: In function `arc_ps2_probe':
/mnt/linux/drivers/input/serio/arc_ps2.c:206: undefined reference to `devm_ioremap_resource'
Signed-off-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes the following warning:
drivers/input/touchscreen/wdt87xx_i2c.c: In function 'wdt87xx_validate_firmware':
>> drivers/input/touchscreen/wdt87xx_i2c.c:472:4: warning: format '%zd' expects argument of type 'signed size_t', but argument 4 has type 'size_t' [-Wformat=]
size, fw->size);
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlWNoSAACgkQMUfUDdst+ymxNQCguSEmkAYNDdLyYhdcOqSxJt9u
U1gAoMThUDoomkx6CTDMU1wn53hxgMk9
=eCUS
-----END PGP SIGNATURE-----
Merge tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here's the tty and serial driver patches for 4.2-rc1.
A number of individual driver updates, some code cleanups, and other
minor things, full details in the shortlog.
All have been in linux-next for a while with no reported issues"
* tag 'tty-4.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (152 commits)
Doc: serial-rs485.txt: update RS485 driver interface
Doc: tty.txt: remove mention of the BKL
MAINTAINERS: tty: add serial docs directory
serial: sprd: check for NULL after calling devm_clk_get
serial: 8250_pci: Correct uartclk for xr17v35x expansion chips
serial: 8250_pci: Add support for 12 port Exar boards
serial: 8250_uniphier: add bindings document for UniPhier UART
serial: core: cleanup in uart_get_baud_rate()
serial: stm32-usart: Add STM32 USART Driver
tty/serial: kill off set_irq_flags usage
tty: move linux/gsmmux.h to uapi
doc: dt: add documentation for nxp,lpc1850-uart
serial: 8250: add LPC18xx/43xx UART driver
serial: 8250_uniphier: add UniPhier serial driver
serial: 8250_dw: support ACPI platforms with integrated DMA engine
serial: of_serial: check the return value of clk_prepare_enable()
serial: of_serial: use devm_clk_get() instead of clk_get()
serial: earlycon: Add support for big-endian MMIO accesses
serial: sirf: use hrtimer for data rx
serial: sirf: correct the fifo empty_bit
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iJ/U
-----END PGP SIGNATURE-----
Merge tag 'media/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Lots of improvements at the DVB API DocBook documentation. Now, the
frontend and the network APIs are fully in sync with the Kernel and
looks more like the rest of the media documentation;
- New frontend driver: cx24120
- New driver for a PCI device: cobalt. This driver is actually not
sold in the market, but it is a good example of a multi-HDMI input
device;
- The dt3155 driver were promoted from staging;
- The mantis driver got remote controller support;
- New V4L2 driver for ST bdisp SoC chipsets;
- Make sparse and smatch happier: several bugs were solved by fixing
the issues reported by those static code analyzers.
- Lots of new device additions, new features, improvements and cleanups
at the existing drivers.
* tag 'media/v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (553 commits)
[media] lmedm04: fix the range for relative measurements
[media] lmedm04: use u32 instead of u64 for relative stats
[media] omap3isp: remove unused var
[media] saa7134: fix page size on some archs
[media] use CONFIG_PM_SLEEP for suspend/resume
[media] tuner-i2c: be consistent with I2C declaration
[media] si470x: cleanup define namespace
[media] bdisp: prevent compiling on random arch
[media] vb2: Don't WARN when v4l2_buffer.bytesused is 0 for multiplanar buffers
[media] MAINTAINERS: Add entry for the Renesas VSP1 driver
[media] videodev2.h: fix copy-and-paste error in V4L2_MAP_XFER_FUNC_DEFAULT
[media] Revert "[media] vb2: Push mmap_sem down to memops"
[media] mantis: cleanup a warning
[media] bdisp-debug: don't try to divide by s64
[media] cx88: don't declare restart_video_queue if not used
[media] au0828: move dev->boards atribuition to happen earlier
[media] lmedm04: implement dvb v5 statistics
[media] bdisp: remove unused var
[media] bdisp: remove needless check
ts2020: fix compilation on i386
...
When applying touchscreen parameters specified in device tree let's make
sure we keep whatever setup was done by the driver and not reset the
missing values to zero.
Reported-by: Pavel Machek <pavel@ucw.cz>
Tested-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
edt-ft5x06 is a touchscreen and thus a direct input device; let's amrk it
as such. This also allows us to drop some initialization code as
input_init_mt_slots() will do that for us.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Instead of iterating over all bits in a bitmap and test them individually
let's siwtch to for_each_set_bit() which is more compact and is also
faster.
Also use bitmap_weight() when counting number of set bits.
This also fixes INPUT_DO_TOGGLE() implementation as it should have used
*_CNT as the upper boundary, not *_MAX.
Signed-off-by: Anshul Garg <aksgarg1989@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"Thanks to Samuel Thibault input device (keyboard) LEDs are no longer
hardwired within the input core but use LED subsystem and so allow use
of different triggers; Hans de Goede did a large update for the ALPS
touchpad driver; we have new TI drv2665 haptics driver and DA9063
OnKey driver, and host of other drivers got various fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (55 commits)
Input: pixcir_i2c_ts - fix receive error
MAINTAINERS: remove non existent input mt git tree
Input: improve usage of gpiod API
tty/vt/keyboard: define LED triggers for VT keyboard lock states
tty/vt/keyboard: define LED triggers for VT LED states
Input: export LEDs as class devices in sysfs
Input: cyttsp4 - use swap() in cyttsp4_get_touch()
Input: goodix - do not explicitly set evbits in input device
Input: goodix - export id and version read from device
Input: goodix - fix variable length array warning
Input: goodix - fix alignment issues
Input: add OnKey driver for DA9063 MFD part
Input: elan_i2c - add product IDs FW names
Input: elan_i2c - add support for multi IC type and iap format
Input: focaltech - report finger width to userspace
tty: remove platform_sysrq_reset_seq
Input: synaptics_i2c - use proper boolean values
Input: psmouse - use true instead of 1 for boolean values
Input: cyapa - fix a few typos in comments
Input: stmpe-ts - enforce device tree only mode
...
This is a driver for Weida HiTech WDT87xx series touchscreen controller.
Signed-off-by: HungNien Chen <hn.chen@weidahitech.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Currently we are reporting the button state as inverted on all boards with
an axp209 pmic, tested on a ba10-tvbox, bananapi, bananapro, cubietruck and
utoo-p66 tablet.
The axp209 datasheet clearly states that the power button must be connected
between the PWRON key and ground. Which means that on a press we will get
a falling edge (dbf) irq not a rising one, and likewise on release we will
get a rising edge (dbr) irq, not a falling one.
This commit swaps the check for the 2 irqs fixing the inverted reporting of
the power button state.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Carlo Caione <carlo@caione.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The controller only receives commands when its present. So for the
correct LED to be lit the LED command has to be sent on the present
event.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Based on Patch by Pierre-Loup A. Griffais <pgriffais@valvesoftware.com>:
Add the logic to set the LEDs on XBox Wireless controllers. Command
sequence found by sniffing the Windows data stream when plugging the
device in.
Updated based on comments on linux-input:
unify codepaths in xpad_send_led_command for wired/ wireless controller.
Also document command values for clarification.
All values tested on Xbox 360 Wireless Controller.
Signed-off-by: Pavel Rojtberg <rojtberg@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
clk_prepare_enable() may fail, so we should better check its return value
and propagate it in the case of error.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The i2c_master_recv() uses readsize to receive data from i2c but compares
to size of rdbuf which is always 27. This would cause problem when the
max_fingers is not 5. Change the comparison value to readsize instead.
Fixes: 36874c7e21 ("Input: pixcir_i2c_ts - support up to 5 fingers and
hardware tracking IDs:)
Cc: stable@vger.kernel.org
Signed-off-by: Frodo Lai <frodo_lai@bcmcom.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for
output. Simplify drivers accordingly.
Note that in the case of the drv260x driver error checking is more
strict now because -ENOSYS is reported to the caller now. But this
should only be returned if GPIOLIB is disabled which shouldn't happen as
the driver depends on GPIOLIB.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Chromebooks can have more than one Embedded Controller so the
cros_ec device id has to be incremented for each EC registered.
Add a new structure to represent multiple EC as different char
devices (e.g: /dev/cros_ec, /dev/cros_pd). It connects to
cros_ec_device and allows sysfs inferface for cros_pd.
Also reduce number of allocated objects, make chromeos sysfs
class object a static and add refcounting to prevent object
deletion while command is in progress.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Reviewed-by: Dmitry Torokhov <dtor@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
The MFD driver should only have the logic to instantiate its child devices
and setup any shared resources that will be used by the subdevices drivers.
The cros_ec MFD is more complex than expected since it also has helpers to
communicate with the EC. So the driver will only get more bigger as other
protocols are supported in the future. So move the communication protocol
helpers to its own driver as drivers/platform/chrome/cros_ec_proto.c.
Suggested-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Commit 1b84f2a4cd ("mfd: cros_ec: Use fixed size arrays to transfer
data with the EC") modified the struct cros_ec_command fields to not
use pointers for the input and output buffers and use fixed length
arrays instead.
This change was made because the cros_ec ioctl API uses that struct
cros_ec_command to allow user-space to send commands to the EC and
to get data from the EC. So using pointers made the API not 64-bit
safe. Unfortunately this approach was not flexible enough for all
the use-cases since there may be a need to send larger commands
on newer versions of the EC command protocol.
So to avoid to choose a constant length that it may be too big for
most commands and thus wasting memory and CPU cycles on copy from
and to user-space or having a size that is too small for some big
commands, use a zero-length array that is both 64-bit safe and
flexible. The same buffer is used for both output and input data
so the maximum of these values should be used to allocate it.
Suggested-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This change creates a new input handler called "leds" that exports LEDs on input
devices as standard LED class devices in sysfs and allows controlling their
state via sysfs or via any of the standard LED triggers. This allows to
re-purpose and reassign LDEs on the keyboards to represent states other
than the standard keyboard states (CapsLock, NumLock, etc).
The old API of controlling input LEDs by writing into /dev/input/eventX
devices is still present and will take precedence over accessing via LEDs
subsystem (i.e. it may override state set by a trigger). If input device is
"grabbed" then requests coming through LED subsystem will be ignored.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use kernel.h macro definition.
Thanks to Julia Lawall for Coccinelle scripting support.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
input_mt_init_slots() will do that for us.
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input layer fix from Dmitry Torokhov:
"A small tweak for the Synaptics PS/2 touchpad driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics - add min/max quirk for Lenovo S540
Goodix touchscreens export through their registers a Product ID and
Firmware Version. The Product ID is an ASCII encoding of the product name
(e.g.: "911").
Export to sysfs (through the input subsystem) the product id and firmware
version read from the device rather than using constant values.
Signed-off-by: Octavian Purdila <octavian.purdila@intel.com>
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix sparse warning:
drivers/input/touchscreen/goodix.c:182:26: warning: Variable length array is used.
Replace the variable length array with fixed length.
Some Goodix devices have maximum 5 touch points, while others have 10 touch
points. Using the maximum length (80 bytes) for all devices will lead to
wasting 40 bytes on stack when using devices with maximum 5 touch points.
However, that is preferable to using kmalloc which will use even more
resources.
Signed-off-by: Irina Tirdea <irina.tirdea@intel.com>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds OnKey driver support for DA9063.
Signed-off-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Previously the elan_i2c touchpad driver would simply request the firmware
"/lib/firmware/elan_i2c.bin", which does not work well if there are
multiple such devices in the system.
Let's append the "product ID" (by using the same function as the sysfs
interface for consistency) to the filename. This results in filenames of
the form "/lib/firmware/elan_i2c_72.0.bin", allowing you to support
multiple elan_i2c touchpads on the same device by simply naming each
device's FW with its corresponding product ID. This way when you trigger a
fw update the driver will load the correct binary.
Signed-off-by: Charlie Mooney <charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In order to support multiple IC types for i2c/smbus protocol, add get ic
type command and use this data when checking firmware page count and
signature address.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This fixes up a merge issue with the amba-pl011.c driver, and we want
the fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull input subsystem fixes from Dmitry Torokhov:
"Just a couple touchpad drivers fixups"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: alps - do not reduce trackpoint speed by half
Input: elantech - add new icbody type
Input: elantech - fix detection of touchpads where the revision matches a known rate
On some v7 devices (e.g. Lenovo-E550) the deltas reported are typically
only in the 0-1 range dividing this by 2 results in a range of 0-0.
And even for v7 devices where this does not lead to making the trackstick
entirely unusable, it makes it twice as slow as before we added v7 support
and were using the ps/2 mouse emulation of the dual point setup.
If some kind of generic slowdown is actually necessary for some devices,
then that belongs in userspace, not in the kernel.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Rico Moorman <rico.moorman@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This adds new icbody type to the list recognized by Elantech PS/2 driver.
Cc: stable@vger.kernel.org
Signed-off-by: Sam Hung <sam.hung@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Focaltech touchpads report finger width in packet[5] of absolute packet.
Range for width in raw format is 0x10 - 0x70. Second half-byte is always 0.
0xff is reported, when a large contact area is detected.
This can be handled in userspace.
Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Make the check to skip the rate check more lax, so that it applies
to all hw_version 4 models.
This fixes the touchpad not being detected properly on Asus PU551LA
laptops.
Cc: stable@vger.kernel.org
Reported-and-tested-by: David Zafra Gómez <dezeta@klo.es>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When stop_streaming is called while a frame is currently being retrieved, the
buffer being filled will still be returned with BUF_STATE_DONE. By resetting
the sequence number and checking before returning the buffer, it can now
correctly be returned with BUF_STATE_ERROR.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add dev_dbg statements for easier future debugging; also change the warning
about packet ID mismatches to debug output to avoid flooding the logs. This
warning is only important in a very specific/rare use case when trying to
correlate input events with video data.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add missing functions to query the single fixed frame size (960x540) and
supported frame rates. Technically, the SUR40 supports any arbitrary frame
rate up to 60 FPS, as it is polled and not interrupt-driven. For now, we
just report 30 and 60 FPS, which is sufficient to make most V4L2 tools work.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The SUR40 hardware can deliver images at up to 60 FPS; at full USB2 bandwidth,
one raw frame will take about 11 ms to transmit. If the poll interval is above
5 ms, fully handling one frame will take longer than 16 ms and the overall
frame rate will drop below 60 FPS. To get the full frame rate without blocking
all the time and still allowing for a bit of timing jitter, we reduce the poll
interval to 4 ms.
Signed-off-by: Martin Kaltenbrunner <modin@yuri.at>
Signed-off-by: Florian Echtler <floe@butterbrot.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Most code already uses consts for the struct kernel_param_ops,
sweep the kernel for the last offending stragglers. Other than
include/linux/moduleparam.h and kernel/params.c all other changes
were generated with the following Coccinelle SmPL patch. Merge
conflicts between trees can be handled with Coccinelle.
In the future git could get Coccinelle merge support to deal with
patch --> fail --> grammar --> Coccinelle --> new patch conflicts
automatically for us on patches where the grammar is available and
the patch is of high confidence. Consider this a feature request.
Test compiled on x86_64 against:
* allnoconfig
* allmodconfig
* allyesconfig
@ const_found @
identifier ops;
@@
const struct kernel_param_ops ops = {
};
@ const_not_found depends on !const_found @
identifier ops;
@@
-struct kernel_param_ops ops = {
+const struct kernel_param_ops ops = {
};
Generated-by: Coccinelle SmPL
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Junio C Hamano <gitster@pobox.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Kees Cook <keescook@chromium.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: cocci@systeme.lip6.fr
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The variable no_decel is bool type so assigning "true" instead of "1".
Also, synaptics_i2c_get_input() has bool return type, so let's use "false"
there.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The variable psmouse_smartscroll is bool type so assigning true
instead of 1.
Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The STMPE MFD is only used with device tree configured systems (and STMPE
MFD core depends on OF), so force the configuration to come from device
tree only.
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When STMPE is instantiated via device tree individual MFD cells rae formed
with OF modaliases, not platform modaliases, and so we need to add OF
device table to the driver if we want it to load automatically:
of:Nstmpe_touchscreenT<NULL>Cst,stmpe-ts
Reported-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input fixes from Dmitry Torokhov:
"Updates for the input subsystem.
The main change is that we tell joydev not to touch "absolute mice",
such as VMware virtual mouse, as that produced bad result (cursor
stuck in upper right corner) with games"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: smtpe-ts - wait 50mS until polling for pen-up
Input: smtpe-ts - use msecs_to_jiffies() instead of HZ
Input: joydev - don't classify the vmmouse as a joystick
Input: vmmouse - do not reference non-existing version of X driver
Input: alps - fix finger jumps on lifting 2 fingers on v7 touchpad
Input: elantech - fix semi-mt protocol for v3 HW
Input: sx8654 - fix memory allocation check
rajeev-dlh.kumar@st.com email-id doesn't exist anymore as I have left the
company.
Signed-off-by: Rajeev Kumar <rajeevkumar.linux@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
gcc-5 defaults to gnu11 which used c99 inline semantics in c99 'inline' is
not externally visible unlike gnu89, therefore we use 'static inline' which
has same semantics between gnu89 and c99
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The I2C subsystem can match devices without explicit OF support based on
the part of their compatible property after the comma. However, this
mechanism uses the first compatible value only. For adxl34x OF device
nodes the compatible property will contain the more specific
"adi,adxl345" or "adi,adxl346" value first. This prevents the device
node from being matched with the adxl34x driver.
Fix this by adding an OF match table with an "adi,adxl345" compatible
entry. There's no need to add the "adi,adxl346" entry as the ADXL346 is
backward-compatible with the ADXL345 with differences handled by runtime
detection of the device model.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
As the name suggests, always_unused argument in cyapa_gen3_set_power_mode()
is never used, so there is no reason for setting it to 0.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Joydev is currently thinking some absolute mice are joystick, and that
messes up games in VMware guests, as the cursor typically gets stuck in
the top left corner.
Try to detect the event signature of a VMmouse input device and back off
for such devices. We're still incorrectly detecting, for example, the
VMware absolute USB mouse as a joystick, but adding an event signature
matching also that device would be considerably more risky, so defer that
to a later merge window.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
This makes the intent a tad more clear.
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The vmmouse Kconfig help text was referring to an incorrect user-space
driver version. Fix this.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
On v7 touchpads sometimes when 2 fingers are moved down on the touchpad
until they "fall of" the touchpad, the second touch will report 0 for y
(max y really since the y axis is inverted) and max x as coordinates,
rather then reporting 0, 0 as is expected for a non touching finger.
This commit detects this and treats these touches as non touching.
See the evemu-recording here:
https://bugzilla.redhat.com/attachment.cgi?id=1025058
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1221200
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Now that the generic process_bitmap function has been improved to offer
accurate coordinates for the first touch we can use it for v5 (dolphin)
touchpads too.
Besides being a nice code cleanup this also fixes the saw tooth pattern
in the coordinates for the second touch the dolphin specific version had.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Rename alps_set_abs_params_mt to alps_set_abs_params_semi_mt,
to make it clear that it is only (to be) used for semi-mt devices.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
With the recent process_bitmap() changes all semi-mt devices always report
the first finger down in slot 0, so stop using input-mt finger tracking
for these.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
All alps semi-mt touchpads give us the following data when 2 (or more)
fingers are touching: 1 more or less accurate touch for the first finger
down, and a bitmap with columns and rows in which 1 or more fingers are
seen resulting in a crude (low res) bounding box.
So far for v3, rushmore and v4 touchpads we've been reporting the
coordinates of 2 opposite corners of the box when 2 fingers are touching.
Ignoring the much better resolution data given in the normal position
packet.
This commit actually uses this data for the first touch, figures out which
corner of the bounding box is closest to the first touch, and reports the
coordinates of the opposite corner for the second touch, resulting in
much better data for the first touch and for the single touch
pointer-emulation events.
This approach is similar to the one in alps_process_bitmap_dolphin, that
function takes the single accurate touch info, calculates the distance to
the center of the bounding box, and then puts the 2nd touch mirrored to
the center. The downside of that approach is that if both touches move
slowly in the same direction, the bounding box will stay the same for a
while (as it is low res) and the second touch will thus been seen moving
in the opposite direction until the bounding box actually changes, and
then the second touch snaps to its new position resulting in a saw tooth
pattern in the coordinates for the second touch, hence this new approach.
This commit fixes 2 finger scrolling being choppy / jumpy on these
touchpads.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We should decode the position packet before the packet with the bitmap
data. This way we can use the more accurate position info in
process_bitmap() to get better results.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pinnacle / Rushmore packets contain either position info, or bitmap info,
never both. So far we've in essence been storing garbage in the position /
bitmap fields of the fields struct when decoding a bitmap / pos packet.
We've been relying on the following sequence to get away with this:
1) Decode bitmap packet
2) Process bitmap packet
3) Decode position packet
4) Use position / button info
This patch allows us to change this sequence, which will allow using the
position info when processing the bitmap for more accurate results.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Change alps_decode_rushmore to do all decoding itself, rather then relying
on alps_decode_pinnacle and then overriding some fields + or-ing in some
bits.
This is a preparation patch for modifying the decode functions to properly
differentiate between position and bitmap packets.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Since commit 1c6c69525b ("genirq: Reject
bogus threaded irq requests") threaded IRQs without a primary handler
need to be requested with IRQF_ONESHOT, otherwise the request will fail.
So pass the IRQF_ONESHOT flag in this case.
The semantic patch that makes this change is available
in scripts/coccinelle/misc/irqf_oneshot.cocci.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
max7359_build_keycode() does the same thing as matrix_keypad_build_keymap(),
but the latter can also handle DT bindings.
Tested on beagleboard-xm.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
In datasheet of max7359 there is the following description of this flag:
0 - INT cleared when FIFO empty,
1 - INT cleared after host read. In this mode, I2C should read
FIFO until interrupt condition removed, or further INT may be lost.
So, if we set this flag, we have to read FIFO until it becomes empty. But
in interrupt we read FIFO just once. This lead to "keyboard" hang until
reboot, if we press several keys, because of interrupt handler read just
one "press" from FIFO and clear interrupt.
Signed-off-by: Evgeniy A. Dushistov <dushistov@mail.ru>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the v3 hardware sees more than one finger, it uses the semi-mt
protocol to report the touches. However, it currently works when
num_fingers is 0, 1 or 2, but when it is 3 and above, it sends only 1
finger as if num_fingers was 1.
This confuses userspace which knows how to deal with extra fingers
when all the slots are used, but not when some are missing.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=90101
Cc: stable@vger.kernel.org
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
We have been testing wrong variable when trying to make sure that input
allocation succeeded.
Reported by Coverity (CID 1295918).
Acked-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add the TI drv2665 piezo haptic driver. This haptics IC requires the data
to be streamed to the FIFO for continuous output.
Datasheet can be found at:
http://www.ti.com/product/drv2665
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Fix the Kconfig for the drv2667 as there was a copy/paste error.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Wait a little bit longer, 50mS instead of 20mS, until the driver starts
polling for pen-up. The problematic behavior before this patch is applied
is as follows. The behavior was observed on the STMPE610QTR controller.
Upon a physical pen-down event, the touchscreen reports one set of x-y-p
coordinates and a pen-down event. After that, the pen-up polling is
triggered and since the controller is not ready yet, the polling mistakenly
detects a pen-up event while the physical state is still such that the pen
is down on the touch surface.
The pen-up handling flushes the controller FIFO, so after that, all the
samples in the controller are discarded. The controller becomes ready
shortly after this bogus pen-up handling and does generate again a pen-down
interrupt. This time, the controller contains x-y-p samples which all read
as zero. Since pressure value is zero, this set of samples is effectively
ignored by userland.
In the end, the driver just bounces between pen-down and bogus pen-up
handling, generating no useful results. Fix this by giving the controller a
bit more time before polling it for pen-up.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Use msecs_to_jiffies(20) instead of plain (HZ / 50), as the former is much
more explicit about it's behavior. We want to schedule the task 20 mS from
now, so make it explicit in the code.
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The MSB of the first byte read via I2C at the coordinates address
indicates whether the data is valid or ready (called "buffer status" in
the datasheets) when an interrupt is raised. Previously, this bit was
ignored, which resulted in a lot of incorrect detections of "finger
removed" events.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Bastien Nocera <hadess@hadess.net>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The event mask was specified as 0xF (4 bits) when in reality is 0x1F (5
bits) in order to be capable of representing all FIFO length values from
0 to 16.
This caused a problem: when the keypad reported 16 pending events the
driver took it as 0, and did nothing. This in turn caused the keypad to
re-issue the interrupt over and over again.
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The pull mask is created by looping each row (column) and building an
8-bit integer with the configuration. It is written byte-by-byte, when
we reach the end of the rows (columns) or we're at the 3rd line (which
finishes the first byte, since each pin is 2bits on the mask).
However, this only works if we have at most 8 pins (2 bytes), which is
not the case for the ADP5589. So, write the byte at each boundary (every
4 rows/columns).
Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
tty_name no longer uses the buf parameter, so remove it along with all
the 64 byte stack buffers that used to be passed in.
Mostly generated by the coccinelle script
@depends on patch@
identifier buf;
constant C;
expression tty;
@@
- char buf[C];
<+...
- tty_name(tty, buf)
+ tty_name(tty)
...+>
allmodconfig compiles, so I'm fairly confident the stack buffers
weren't used for other purposes as well.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Peter Hurley <peter@hurleysoftware.com>
Acked-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's a set of updates to the Chrome OS platform drivers for this merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can make your
own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The laptop driver
is trying to be smart and not instantiate the devices that don't answer to
probe. For the trackpad that can come up in two modes (bootloader or regular),
this gets complicated since the driver already knows how to handle the two
modes including the actual addresses used. So now the laptop driver needs to
know more too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few bugfixes
from him, kbuild and myself.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=NVa4
-----END PGP SIGNATURE-----
Merge tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's a set of updates to the Chrome OS platform drivers for this
merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can
make your own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The
laptop driver is trying to be smart and not instantiate the devices
that don't answer to probe. For the trackpad that can come up in
two modes (bootloader or regular), this gets complicated since the
driver already knows how to handle the two modes including the
actual addresses used. So now the laptop driver needs to know more
too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few
bugfixes from him, kbuild and myself"
* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: chromeos_laptop - instantiate Atmel at primary address
platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
platform/chrome: cros_ec_lpc - Include linux/io.h header file
platform/chrome: fix platform_no_drv_owner.cocci warnings
platform/chrome: cros_ec_lightbar - fix duplicate const warning
platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
platform/chrome: Expose Chrome OS Lightbar to users
platform/chrome: Create sysfs attributes for the ChromeOS EC
mfd: cros_ec: Instantiate ChromeOS EC character device
platform/chrome: Add Chrome OS EC userspace device interface
platform/chrome: Add cros_ec_lpc driver for x86 devices
mfd: cros_ec: Add char dev and virtual dev pointers
mfd: cros_ec: Use fixed size arrays to transfer data with the EC
Pull more input subsystem updates from Dmitry Torokhov:
- an update to Atmel MXT driver that makes it functional on Google
Pixel 2 boxes (both touchpad and touchscreen)
- a new VMware VMMouse driver that should allow us drop X vmmouse
driver that requires root privileges (since it accesses ioports)
- XBox One controllers now support force feedback (rumble)
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: lm8333 - fix broken email address
Input: cyapa - fix setting suspend scan rate
Input: elan_i2c - fix calculating number of x and y traces.
Input: elan_i2c - report hovering contacts
Input: elants_i2c - zero-extend hardware ID in firmware name
Input: alps - document separate pointstick button bits for V2 devices
Input: atmel_mxt_ts - add support for Google Pixel 2
Input: xpad - add rumble support for Xbox One controller
Input: ff-core - use new debug macros
Input: add vmmouse driver
Input: elan_i2c - adjust for newer firmware pressure reporting
* 'drm-next-merged' of git://people.freedesktop.org/~airlied/linux: (9717 commits)
media-bus: Fixup RGB444_1X12, RGB565_1X16, and YUV8_1X24 media bus format
hexdump: avoid warning in test function
fs: take i_mutex during prepare_binprm for set[ug]id executables
smp: Fix error case handling in smp_call_function_*()
iommu-common: Fix PARISC compile-time warnings
sparc: Make LDC use common iommu poll management functions
sparc: Make sparc64 use scalable lib/iommu-common.c functions
Break up monolithic iommu table/lock into finer graularity pools and lock
sparc: Revert generic IOMMU allocator.
tools/power turbostat: correct dumped pkg-cstate-limit value
tools/power turbostat: calculate TSC frequency from CPUID(0x15) on SKL
tools/power turbostat: correct DRAM RAPL units on recent Xeon processors
tools/power turbostat: Initial Skylake support
tools/power turbostat: Use $(CURDIR) instead of $(PWD) and add support for O= option in Makefile
tools/power turbostat: modprobe msr, if needed
tools/power turbostat: dump MSR_TURBO_RATIO_LIMIT2
tools/power turbostat: use new MSR_TURBO_RATIO_LIMIT names
Bluetooth: hidp: Fix regression with older userspace and flags validation
config: Enable NEED_DMA_MAP_STATE by default when SWIOTLB is selected
perf/x86/intel/pt: Fix and clean up error handling in pt_event_add()
...
That solves several merge conflicts:
Documentation/DocBook/media/v4l/subdev-formats.xml
Documentation/devicetree/bindings/vendor-prefixes.txt
drivers/staging/media/mn88473/mn88473.c
include/linux/kconfig.h
include/uapi/linux/media-bus-format.h
The ones at subdev-formats.xml and media-bus-format.h are not trivial.
That's why we opted to merge from DRM.
My Pengutronix address is not valid anymore, redirect people to the
Pengutronix kernel team.
Reported-by: Harald Geyer <harald@ccbib.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
The suspend scan rate value should not exceed 1000, unfortunately when
implementing the limit we used max_t instead of min_t, causing the value to
be at least 1000.
Signed-off-by: Dudley Du <dudl@cypress.com>
Reviewed-by: Benson Leung <bleung@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
According to Elan's firmware engineers we should not be subtracting 1 form
the raw number of x and y traces so that the pitch size is correct. For
example, if the touchpad x resolution is 2800 and x trace number is 20,
the pitch size of x should be 2800/20 = 140, not 2800/19 = 147.36.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When hover is detected report ABS_MT_DISTANCE as 1; for active contacts
the distance is reported as 0.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Let's zero-extend hardware id number when forming firmware file name,
to avoid kernel requesting firmware like "elants_i2c_ 0.bin", which
is quite unexpected.
Acked-by: Charlie Mooney<charliemooney@chromium.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
cycle:
- A new GPIO hogging mechanism has been added. This can
be used on boards that want to drive some GPIO line high,
low, or set it as input on boot and then never touch it
again. For some embedded systems this is bliss and
simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs
in bulk as was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header
any GPIO driver needs to include or something is wrong.
Cleanups restricting drivers to this include are welcomed
if tested.
- Sort the GPIO Kconfig and split it into submenus, as
it was becoming and unstructured, illogical and
unnavigatable mess. I hope this is easier to follow.
Menus that require a certain subsystem like I2C can
now be hidden nicely for example, still working on
others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and
F71869A variants.
- The MIPS Loongson driver has been moved to
drivers/gpio for consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is
a "hard IP" block from Synopsys which has started to
turn up in so diverse architectures as X86 Quark, ARC
and a slew of ARM systems. So even though it's not an
expander, it's generic enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long
discussion with Daniel Vetter et al, tracing back to
the shootout at the kernel summit where DRM drivers
and sub-componentization was discussed. In this case
a mock GPIO is assumed to be the best compromise
gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's
see.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=QFbC
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.1 development cycle:
- A new GPIO hogging mechanism has been added. This can be used on
boards that want to drive some GPIO line high, low, or set it as
input on boot and then never touch it again. For some embedded
systems this is bliss and simplifies things to a great extent.
- Some API cleanup and closure: gpiod_get_array() and
gpiod_put_array() has been added to get and put GPIOs in bulk as
was possible with the non-descriptor API.
- Encapsulate cross-calls to the pin control subsystem in
<linux/gpio/driver.h>. Now this should be the only header any GPIO
driver needs to include or something is wrong. Cleanups
restricting drivers to this include are welcomed if tested.
- Sort the GPIO Kconfig and split it into submenus, as it was
becoming and unstructured, illogical and unnavigatable mess. I
hope this is easier to follow. Menus that require a certain
subsystem like I2C can now be hidden nicely for example, still
working on others.
- New drivers:
- New driver for the Altera Soft GPIO.
- The F7188x driver now handles the F71869 and F71869A variants.
- The MIPS Loongson driver has been moved to drivers/gpio for
consolidation and cleanup.
- Cleanups:
- The MAX732x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- The PCF857x is converted to use the GPIOLIB_IRQCHIP
infrastructure.
- Radical cleanup of the OMAP driver.
- Misc:
- Enable the DWAPB GPIO for all architectures. This is a "hard
IP" block from Synopsys which has started to turn up in so
diverse architectures as X86 Quark, ARC and a slew of ARM
systems. So even though it's not an expander, it's generic
enough to be available for all.
- We add a mock GPIO on Crystalcove PMIC after a long discussion
with Daniel Vetter et al, tracing back to the shootout at the
kernel summit where DRM drivers and sub-componentization was
discussed. In this case a mock GPIO is assumed to be the best
compromise gaining some reuse of infrastructure without making
DRM drivers overly complex at the same time. Let's see"
* tag 'gpio-v4.1-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (62 commits)
Revert "gpio: sch: use uapi/linux/pci_ids.h directly"
gpio: dwapb: remove dependencies
gpio: dwapb: enable for ARC
gpio: removing kfree remove functionality
gpio: mvebu: Fix mask/unmask managment per irq chip type
gpio: split GPIO drivers in submenus
gpio: move MFD GPIO drivers under their own comment
gpio: move BCM Kona Kconfig option
gpio: arrange SPI Kconfig symbols alphabetically
gpio: arrange PCI GPIO controllers alphabetically
gpio: arrange I2C Kconfig symbols alphabetically
gpio: arrange Kconfig symbols alphabetically
gpio: ich: Implement get_direction function
gpio: use (!foo) instead of (foo == NULL)
gpio: arizona: drop owner assignment from platform_drivers
gpio: max7300: remove 'ret' variable
gpio: use devm_kzalloc
gpio: sch: use uapi/linux/pci_ids.h directly
gpio: x-gene: fix devm_ioremap_resource() check
gpio: loongson: Add Loongson-3A/3B GPIO driver support
...
This change allows atmel_mxt_ts to bind to ACPI-enumerated devices in
Google Pixel 2 (2015).
While newer version of ACPI standard allow use of device-tree-like
properties in device descriptions, the version of ACPI implemented in
Google BIOS does not support them, and we have to resort to DMI data to
specify exact characteristics of the devices (touchpad vs. touchscreen,
GPIO to button mapping, etc).
Pixel 1 continues to use i2c devices and platform data created by
chromeos-laptop driver, since ACPI does not enumerate them.
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull input subsystem updates from Dmitry Torokhov:
"You will get the following new drivers:
- Qualcomm PM8941 power key drver
- ChipOne icn8318 touchscreen controller driver
- Broadcom iProc touchscreen and keypad drivers
- Semtech SX8654 I2C touchscreen controller driver
ALPS driver now supports newer SS4 devices; Elantech got a fix that
should make it work on some ASUS laptops; and a slew of other
enhancements and random fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (51 commits)
Input: alps - non interleaved V2 dualpoint has separate stick button bits
Input: alps - fix touchpad buttons getting stuck when used with trackpoint
Input: atkbd - document "no new force-release quirks" policy
Input: ALPS - make alps_get_pkt_id_ss4_v2() and others static
Input: ALPS - V7 devices can report 5-finger taps
Input: ALPS - add support for SS4 touchpad devices
Input: ALPS - refactor alps_set_abs_params_mt()
Input: elantech - fix absolute mode setting on some ASUS laptops
Input: atmel_mxt_ts - split out touchpad initialisation logic
Input: atmel_mxt_ts - implement support for T100 touch object
Input: cros_ec_keyb - fix clearing keyboard state on wakeup
Input: gscps2 - drop pci_ids dependency
Input: synaptics - allocate 3 slots to keep stability in image sensors
Input: Revert "Revert "synaptics - use dmax in input_mt_assign_slots""
Input: MT - make slot assignment work for overcovered solutions
mfd: tc3589x: enforce device-tree only mode
Input: tc3589x - localize platform data
Input: tsc2007 - Convert msecs to jiffies only once
Input: edt-ft5x06 - remove EV_SYN event report
Input: edt-ft5x06 - allow to setting the maximum axes value through the DT
...
This adds rumble support for Xbox One controller by sending continuous
rumble command. Trigger button rumbling is not yet implemented.
Signed-off-by: Ming-ting Yao Wei <mwei@lxde.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
VMMouse enables low-latency mouse-cursor-movements for VMWare and QEMU
guests. By removing the guest cursor and using the host as a guest cursor
the cursor movement appears instant although in reality there is some lag.
To be able to do this, the host's view of the cursor position must exactly
match the guest's view and an absolute pointer device is needed. Enter the
VMMouse. While the VMMouse driver has historically been an Xorg user-space
driver, implementing it as a kernel imput driver enables rootless Xorg and
new compositing display servers for VMware guests.
Signed-off-by: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Get pressure format flag from firmware to check if we need to normalize
pressure data before reporting it.
Signed-off-by: Duson Lin <dusonlin@emc.com.tw>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Pull HID updates from Jiri Kosina:
- quite a few firmware fixes for RMI driver by Andrew Duggan
- huion and uclogic drivers have been substantially overlaping in
functionality laterly. This redundancy is fixed by hid-huion driver
being merged into hid-uclogic; work done by Benjamin Tissoires and
Nikolai Kondrashov
- i2c-hid now supports ACPI GPIO interrupts; patch from Mika Westerberg
- Some of the quirks, that got separated into individual drivers, have
historically had EXPERT dependency. As HID subsystem matured (as
well as the individual drivers), this made less and less sense. This
dependency is now being removed by patch from Jean Delvare
- Logitech lg4ff driver received a couple of improvements for mode
switching, by Michal Malý
- multitouch driver now supports clickpads, patches by Benjamin
Tissoires and Seth Forshee
- hid-sensor framework received a substantial update; namely support
for Custom and Generic pages is being added; work done by Srinivas
Pandruvada
- wacom driver received substantial update; it now supports
i2c-conntected devices (Mika Westerberg), Bamboo PADs are now
properly supported (Benjamin Tissoires), much improved battery
reporting (Jason Gerecke) and pen proximity cleanups (Ping Cheng)
- small assorted fixes and device ID additions
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (68 commits)
HID: sensor: Update document for custom sensor
HID: sensor: Custom and Generic sensor support
HID: debug: fix error handling in hid_debug_events_read()
Input - mt: Fix input_mt_get_slot_by_key
HID: logitech-hidpp: fix error return code
HID: wacom: Add support for Cintiq 13HD Touch
HID: logitech-hidpp: add a module parameter to keep firmware gestures
HID: usbhid: yet another mouse with ALWAYS_POLL
HID: usbhid: more mice with ALWAYS_POLL
HID: wacom: set stylus_in_proximity before checking touch_down
HID: wacom: use wacom_wac_finger_count_touches to set touch_down
HID: wacom: remove hardcoded WACOM_QUIRK_MULTI_INPUT
HID: pidff: effect can't be NULL
HID: add quirk for PIXART OEM mouse used by HP
HID: add HP OEM mouse to quirk ALWAYS_POLL
HID: wacom: ask for a in-prox report when it was missed
HID: hid-sensor-hub: Fix sparse warning
HID: hid-sensor-hub: fix attribute read for logical usage id
HID: plantronics: fix Kconfig default
HID: pidff: support more than one concurrent effect
...
Non interleaved V2 dualpoint touchpad / stick combos have separate stick
button bits in the touchpad packets, if we do not check these then the
trackpoint buttons will not work when using the touchpad, and when pressed
when the user starts using the touchpad will report a release event even
though the button is still pressed.
This commit fixes this by checking the separate bits, note that we simply
combine the buttons, since the hardware does the same when using the touchpad
buttons with the trackpoint, so we do not have enough information to properly
separate them.
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
When the left touchpad button gets pressed, and then the trackpoint is
moved, and then the button is released, the following happens:
1) touchpad packet is received, touchpad evdev node reports BTN_LEFT 1
2) pointing stick packet is received, the hw will report a BTN_LEFT 1 in
this packet because when the trackstick is active it communicates the
combined touchpad + pointing stick buttons in the trackstick packet,
since alps_report_bare_ps2_packet passes NULL (*) for the dev2 parameter
to alps_report_buttons the combining is not detected and the
pointing stick evdev node will also report BTN_LEFT 1
3) on release of the button a pointing stick packet with BTN_LEFT 0 is
received and the pointing stick evdev node will report BTN_LEFT 0
Note how because of the passing as NULL for dev2 the touchpad evdev node
will never send BTN_LEFT 0 in this scenario leading to a stuck mouse button.
This is a regression in 4.0 introduced by commit 04aae283ba
("Input: ALPS - do not mix trackstick and external PS/2 mouse data")
This commit fixes this by passing in the touchpad evdev as dev2 parameter
when calling alps_report_buttons for the pointingstick on alps v2 devices,
so that alps_report_buttons correctly detect that we're already reporting
the button as pressed via the touchpad evdev node, and will also send the
release event there.
Cc: stable@vger.kernel.org # 4.0
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
