With multi queue devices, its possible that several cpus call
macvlan RX routines simultaneously for the same macvlan device.
We update RX stats counter without any locking, so we can
get slightly wrong counters.
One possible fix is to use percpu counters, to get precise
accounting and also get guarantee of no cache line ping pongs
between cpus.
Note: this adds 16 bytes (32 bytes on 64bit arches) of percpu
data per macvlan device.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dave,
Attached is an update of my patch against the cpufreq fixes branch.
Before applying the patch I compiled and booted the tree to see if the panic
was still there -- to my surprise it was not. This is because of the conversion
of cpufreq_cpu_governor to a char[].
While the panic is kaput, the problem of stale data continues and my patch is
still valid. It is possible to end up with the wrong governor after hotplug
events because CPUFREQ_DEFAULT_GOVERNOR is statically linked to a default,
while the cpu siblings may have had a different governor assigned by a user.
ie) the patch is still needed in order to keep the governors assigned
properly when hotplugging devices
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Dave Jones <davej@redhat.com>
ondemand and conservative governors are messing up time units in the
code path where NO_HZ is not enabled and ignore_nice is set. The walltime
idletime stored is in jiffies and nice time calculation is happening in
microseconds.
The problem was reported and diagnosed by Alexander here.
http://marc.info/?l=linux-kernel&m=125752550404513&w=2
The patch below fixes this thinko.
Reported-by: Alexander Miller <Miller@fmi.uni-stuttgart.de>
Tested-by: Alexander Miller <Miller@fmi.uni-stuttgart.de>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Currently on governer backup/restore path we storing governor's pointer.
This is wrong because one may unload governor's module after cpu goes
offline. As result use-after-free will take place on restored cpu.
It is not easy to exploit this bug, but still we have to close this
issue ASAP. Issue was introduced by following commit
084f349394
##TESTCASE##
#!/bin/sh -x
modprobe acpi_cpufreq
# Any non default governor, in may case it is "ondemand"
modprobe cpufreq_ondemand
echo ondemand > /sys/devices/system/cpu/cpu0/cpufreq/scaling_governor
rmmod acpi_cpufreq
rmmod cpufreq_ondemand
modprobe acpi_cpufreq # << use-after-free here.
Signed-off-by: Dmitry Monakhov <dmonakhov@openvz.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The return should be negative on errors
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Return a negative error value instead of a positive
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: dmitry pervushin <dpervushin@embeddedalley.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add D-Link DWM-162-U5 device id 1e0e:ce16 into option driver. The device
has 4 interfaces, of which 1 is handled by storage and the other 3 by
option driver.
The device appears first as CD-only 05c6:2100 device and must be
switched to 1e0e:ce16 mode either by using "eject CD" or usb_modeswitch.
The MessageContent for usb_modeswitch.conf is:
"55534243e0c26a85000000000000061b000000020000000000000000000000"
Signed-off-by: Zhang Le <r0bertz@gentoo.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1299b) fixes a bug in an error-handling path of usbmon's
binary interface. The storage area for URB data is divided into
fixed-size blocks. If an URB's data can't be copied, the area
reserved for it should be decreased to the size of the truncated
information (rounded up to a block boundary). Rounding up the amount
to be removed and subtracting it from the reserved size is definitely
the wrong thing to do.
Also, when the data for an isochronous URB can't be copied, we can
still copy the isoc packet descriptors. In fact the current code does
copy the descriptors, but then sets the capture length to 0 so they
remain inaccessible. The capture length should be reduced to the
length of the descriptors, not set to 0.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The scratchpad_free() function uses xhci->page_size to free some memory
with pci_free_consistent(). However, the page_size is set to zero before
the call, causing kernel oopses on driver unload. Call scratchpad_free()
before setting xhci->page_size to zero.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Acked-by: John Youn <John.Youn@synopsys.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The trb_in_td() function in the xHCI driver is supposed to translate a
physical transfer buffer request (TRB) into a virtual pointer to the ring
segment that TRB is in.
Unfortunately, a mistake in this function may cause endless loops as the
driver searches through the linked list of ring segments over and over
again. Fix a couple bugs that may lead to loops or bad output:
1. Bail out if we get a NULL pointer when translating the segment's
private structure and the starting DMA address of the segment chunk. If
this happens, we've been handed a starting TRB pointer from a different
ring.
2. Make sure the function works when there's multiple segments in the
ring. In the while loop to search through the ring segments, use the
current segment variable (cur_seg), rather than the starting segment
variable (start_seg) that is passed in.
3. Stop searching the ring if we've run through all the segments in the
ring.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the xHCI driver fails during the memory initialization, xhci->ir_set
may not be a valid pointer. Check that it points to valid DMA'able memory
before writing to that address during the memory freeing process.
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Donnerstag, 10. September 2009 15:43:53 schrieb Dietmar Hilbrich:
> Hello,
>
> i have the following problem with the cdc-acm - driver:
>
> I'm using the driver with an "Ericsson F3507G" on a Thinkpad T400.
>
> If a disable the device (with the RFKill-Switch) while it is used by a
> programm like ppp, the driver doesn't seem to correctly clean up the tty,
> even after the program has been closed)
>
> The tty is still active (e.g. there still exists an entry in
> /sys/dev/char/166:0 if ttyACM0 was used) and if a reacticate the device,
> this device entry will be skipped and the Device-Nodes ttyACM1, ttyACM2
> and ttyACM3 will be used.
>
> This problem was introduced with the commit
> 10077d4a66 (before 2.6.31-rc1) and still
> exists in 2.6.31.
>
> I was able the fix this problem with the following patch:
>
> diff --git a/drivers/usb/class/cdc-acm.c b/drivers/usb/class/cdc-acm.c
> index 2bfc41e..0970d2f 100644
> --- a/drivers/usb/class/cdc-acm.c
> +++ b/drivers/usb/class/cdc-acm.c
> @@ -676,6 +676,7 @@ static void acm_tty_hangup(struct tty_struct *tty)
> struct acm *acm = tty->driver_data;
> tty_port_hangup(&acm->port);
> acm_port_down(acm, 0);
> + acm_tty_unregister(acm);
> }
I have the same problem with cdc-acm (I'm using a Samsung SGH-U900): when I
unplug it from the USB port during a PPP connection, the ppp daemon gets the
hangup correctly (and closes the device), but the struct acm corresponding to
the device disconnected is not freed. Hence reconnecting the device results in
creation of /dev/ttyACM(x+1). The same happens when the system is hibernated
during a PPP connection.
This memory leak is due to the fact that when the tty is hung up,
tty_port_close_start() returns always zero, and acm_tty_close() never reaches
the point where acm_tty_unregister() is called.
Here is a fix for this.
Signed-off-by: Francesco Lavra <francescolavra@interfree.it>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If acm_rx_tasklet() gets called before tty_port_block_til_ready()
returns, then bulk IN urbs may not be sent. This fixes it.
Signed-off-by: Henry Gebhardt <gebhardt@astro.uni-tuebingen.de>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch in the driver is required to avoid USB 1.1 device
failures that may occur due to requests from USB OHCI controllers may
be overwritten if the latency for any pending request by the USB
controller is very long (in the range of milliseconds).
Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=29a68e39d4a broke carrier handling so that a
cp210x setup which needed the carrier lines set up (non CLOCAL) which did
not make a call which set the termios bits left the lines down even if
CLOCAL was not asserted.
Fix this not by reverting but by adding the proper dtr_rts and
carrier_raised methods. This both sets the modem lines properly and also
implements the correct blocking semantics for the port as required by
POSIX.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Tested-by: Karl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Original discussion:
http://thread.gmane.org/gmane.linux.usb.general/23217/focus=23248
or
http://marc.info/?l=linux-usb&m=125553790714133&w=2
The tty_port code inherited a bug common to various drivers it was based
upon. If the tty is opened O_NONBLOCK we do not wait for the carrier to be
raised but we must still raise our modem lines if appropriate.
(There is a second question here about whether we should do so if CLOCAL is
set but that can wait)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Reported-by: Karl Hiramoto <karl@hiramoto.org>
Tested-by: Karl Hiramoto <karl@hiramoto.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] bfa: declare MODULE_FIRMWARE
[SCSI] gdth: Prevent negative offsets in ioctl CVE-2009-3080
[SCSI] libsas: do not set res = 0 in sas_ex_discover_dev()
[SCSI] Fix incorrect reporting of host protection capabilities
[SCSI] pmcraid: Fix ppc64 driver build for using cpu_to_le32 on U8 data type
[SCSI] ipr: add workaround for MSI interrupts on P7
[SCSI] scsi_transport_fc: Fix WARN message for FC passthru failure paths
[SCSI] bfa: fix test in bfad_os_fc_host_init()
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: ensure mfp is in correct range in mfp_{read,write}
[ARM] pxa/hx4700: fix hx4700 touchscreen pressure values
ARM: 5787/1: U300 COH 901 331 fixes
ARM: Fix warning in sa1100-flash.c
[ARM] Kirkwood: disable propagation of mbus error to the CPU local bus
[ARM] pxa: fix incorrect mfp_to_gpio() conversion
[ARM] pxa/colibri: fix AC97 ifdefs and add missing include
[ARM] pxa: fix missing underscores in mfp-pxa910.h
[ARM] pxa: fix interrupts number calculation when CONFIG_PXA_HAVE_ISA_IRQS=y
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
dereferencing freed memory regulator_fixed_voltage_remove()
regulator: Fix check of unsigned return value and transmit errors in wm831x_gp_ldo_get_mode()
regulator: Handle missing constraints in _regulator_disable()
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds-gpio: fix possible crash on OF device unbinding
backlight: Fix backlight limiting on spitz/corgi devices
backlight: lcd - Fix wrong sizeof
* 'hostprogs-wmissing-prototypes' of git://git.kernel.org/pub/scm/linux/kernel/git/josh/linux-misc:
Makefile: Add -Wmising-prototypes to HOSTCFLAGS
oss: Mark loadhex static in hex2hex.c
dtc: Mark various internal functions static
dtc: Set "noinput" in the lexer to avoid an unused function
drm: radeon: Mark several functions static in mkregtable
arch/sparc/boot/*.c: Mark various internal functions static
arch/powerpc/boot/addRamDisk.c: Mark several internal functions static
arch/alpha/boot/tools/objstrip.c: Mark "usage" static
Documentation/vm/page-types.c: Declare checked_open static
genksyms: Mark is_reserved_word static
kconfig: Mark various internal functions static
kconfig: Make zconf.y work with current bison
znet was including "wireless/i82593.h" (which is a bit wierd), and I
missed that when I relocated i82593.h to drivers/staging/wavelan. Since
I don't have ISA turned-on in my normal .config, I didn't see the build
failures -- mea culpa!
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add missing 'const' attribute to avoid the following compile warnings:
drivers/s390/net/ctcm_main.c: In function 'ctcm_init':
drivers/s390/net/ctcm_main.c:1864: warning: assignment from incompatible pointer type
drivers/s390/net/lcs.c: In function 'lcs_init_module':
drivers/s390/net/lcs.c:2468: warning: assignment from incompatible pointer type
drivers/s390/net/claw.c: In function 'claw_init':
drivers/s390/net/claw.c:3408: warning: assignment from incompatible pointer type
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to look for the 'shared-pins' property to get
this right.
Based upon a patch by Hermann Lauer.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes config dependency on x86 to build vmxnet3 driver. Thus
the driver can be built on big endian architectures now. Although vmxnet3
is not supported on VMs other than x86 architecture, all this code goes in
to ensure correctness. If the code is not dependent on x86, it should not
assume little endian architecture in any of its operations.
Signed-off-by: Shreyas Bhatewara <sbhatewara@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Put Tx and Rx DPC to be handled in the NAPI:
- Saves status blocks.
- Moves the Tx work from hardIRQ to NAPI.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes the following warning:
WARNING: drivers/net/phy/built-in.o(.devexit.text+0x70): Section mismatch in reference from the function .mdio_gpio_bus_destroy() to the function .devinit.text:.mdio_gpio_bus_deinit()
The function __devexit .mdio_gpio_bus_destroy() references
a function __devinit .mdio_gpio_bus_deinit().
This is often seen when error handling in the exit function
uses functionality in the init path.
The fix is often to remove the __devinit annotation of
.mdio_gpio_bus_deinit() so it may be used outside an init section.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
1. This patch is based on the kernel of 2.6.32-rc7
2. In this patch, we enlarge the out buffer size to optimize the
upload speed for the ppp connection. Then it can support the upload of
HSUPA data cards.
Signed-off-by: fangxiaozhi <huananhu@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- move Kconfig entries to the subdirectory
- do remaining renames of mpc52xx to mpc5xxx
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all hardcoded values have been replaced as this made the code quite
unreadable. IMHO this compromise serves the purpose of readability.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge two functions into one. The result is smaller as they can now share some
variables.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- use extern where apropriate
- don't export symbols
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
- remove whitespaces
- use ! and ?: when apropriate
- make braces consistent
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
ks8695_rx() will call refill_buffers() for every incoming packet.
Its not necessary. We just need do it after finishing receiving thing.
And the 'RX dma engine' is in the same situation.
This blocks our user space application. The following patch may fix it.
Signed-off-by: zeal <zealcook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ks8695 rx irq is edge-level. Before arriving at irq handler, the
corresponding status bit has been clear(irq's ack).
So we should not check it after that.
Signed-off-by: zeal <zealcook@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PPP does not correctly call pskb_may_pull() on all necessary receive paths
before reading the PPP protocol, thus causing PPP to report seemingly
random 'unsupported protocols' and eventually trigger BUG_ON(skb->len <
skb->data_len) in skb_pull_rcsum() when receiving multilink protocol in
non-linear skbs.
ppp_receive_nonmp_frame() does not call pskb_may_pull() before reading the
protocol number. For the non-mp receive path this is not a problem, as
this check is done in ppp_receive_frame(). For the mp receive path,
ppp_mp_reconstruct() usually copies the data into a new linear skb.
However, in the case where the frame is made up of a single mp fragment,
the mp header is pulled and the existing skb used. This skb was then
passed to ppp_receive_nonmp_frame() without checking if the encapsulated
protocol header could safely be read.
Signed-off-by: Ben McKeegan <ben@netservers.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commmit 4b77b0a2ba EEH breaks
after the second error, since it calls pci_restore_state()
but it returns 0, since pci->state_saved is false.
So, this patch just call pci_save_state() after pci_restore_state().
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Panasonic CF-72 uses 6-byte protocol and does not need to be tied
to a particular port.
Signed-off-by: Abner Holsinger <9zabner@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit b7802c5c1e ("Input: psmouse - use boolean type") caused the
synaptics_hardware variable to be completely useless, as it is
constantly set to 'true' throughout the whole psmouse_extensions().
This was caused by the following hunk in the commit in question
- int synaptics_hardware = 0;
+ bool synaptics_hardware = true;
which is wrong and causes driver to issue extra reset when falling
back to bare PS/2 protocol.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
As a holdover from earlier code when we used to set
the power limit to '0' after a reset to configure the
default transmit power, ath5k interprets txpower=0 as
12.5 dBm. Fix that by just passing 0 through.
This fixes http://bugzilla.kernel.org/show_bug.cgi?id=14567
Cc: stable@kernel.org
Reported-by: Daniel Folkers <daniel.folkers@task24.nl>
Tested-by: Daniel Folkers <daniel.folkers@task24.nl>
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rndis_wlan didn't know about NL80211_AUTHTYPE_AUTOMATIC and simple
setup with 'iwconfig wlan essid no-encrypt' would fail (ENOSUPP).
v2: use NDIS_80211_AUTH_AUTO_SWITCH instead of _OPEN.
This will make device try shared key auth first, then open.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Please be gentle, I'm a fs developer and this is my first foray into drivers, as
I'm tired of building ralinks driver everytime I update my kernel. Whenever I
load the rt2800pci driver my box bogs down, and a few printk's later I
discovered its because I was getting 10's of thousands of TBTT interrupts a
second. I discovered this was because we were setting the beacon timer to 0,
which is apparently what TBTT keys off of. It seems to me that we should only
be enabling TBTT when we are in a beacon transmitting mode, which from what I
can tell is in AD-HOC and other such modes where the mac80211 layer would have
given us a proper beacon_int to set the beacon timer to instead of 0. So this
is my fix, only enable TBTT if our sync mode is for beacon. This makes it so my
box doesn't die everytime I load the rt2800pci driver. Let me know if this is
acceptable, I just learned all these terms about 15 minutes ago via wikipedia,
so I really am not familiar with how this stuff is supposed to work. Thanks,
Signed-off-by: Josef Bacik <josef@redhat.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes a regression introduced in
"ath9k: avoid the copy skb->cb on every RX'd skb"
With that change, the rx status in skb->cb was left uninitialized
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current tree hits a BUG_ON in rt2x00_regbusy_read, because the eFuse EEPROM
reading code of rt2800lib uses the function without the csr_mutex locked.
Fix this by locking the csr_mutex for the of the EEPROM reading cycly and
using the _lock variants of the register reading and writing functions.
This also introcudes the register_read_lock function pointer in the
rt2800_ops structure.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some drivers (rt2800* most notably) cannot set the RF and RT chipset in
the correct order to have the information logging in rt2x00_set_chip
be correct.
Fix this by decoupling the setting of the chipset information from the
logging of the chipset information so that drivers can determine
themselves when all information is set.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Ensure RF302x and RF2020 chipsets are handled properly in rt2800lib
for the rt3090 chipset.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mirror the legacy Ralink driver with respect to rt2800 RF register
programming. Execute rt2800_config_channel_rt3x for all RF2020,
RF3020, RF3021 & RF3022 chipsets when operating on RT3070 devices.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will fix some small issues with the COH 901 331 RTC driver:
- Interrupt is disabled after alarm so that we don't fire
multiple interrupts.
- We return 0 from the coh901331_alarm_irq_enable() ridding
a compile warning.
- We alter the name in the U300 device registry to match that
of the driver so they sucessfully resolve.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
drivers/mtd/maps/sa1100-flash.c: In function 'sa1100_probe_subdev':
drivers/mtd/maps/sa1100-flash.c:214: warning: format '%d' expects type 'int', but argument 3 has type 'uint64_t'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't dereference drvdata after it has been freed.
regards,
dan carpenter
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
If there are leds present in the OF tree, but the GPIOs for (some) of
them are unavailable, led_data doesn't get populated with correct
devices. Then, on device unbinding, one can crash the kernel.
Workaround this by setting led->gpio to invalid value early.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
On spitz (& similar) machines, if battery is running low, backlight
needs
to be limited to lower step. Unfortunately, current code uses &= for
limiting, turning backlight off completely for some backlight settings.
Fix that.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
Which is why I have always preferred sizeof(struct foo) over
sizeof(var).
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Richard Purdie <rpurdie@linux.intel.com>
The adt7475 driver creates pwm#_auto_channel_temp attributes instead
of the standard pwm#_auto_channels_temp. Fix it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
The comment says that limits are cached for 60 seconds but the code
actually caches them for only 2 seconds. Align the code on the
comment, as 60 seconds makes more sense.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
The logic of temperature fault flags is wrong, it shows faults when
there are none and vice versa. Fix it.
I can't believe this has been broken since the driver was added, 8
months ago, basically breaking temp1 and temp3, and nobody ever
complained.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Cc: Jordan Crouse <jordan@cosmicpenguin.net>
Avoid registering channels that have zero divider settings in them, as this
will only lead to kernel OOPS from divide-by-zero when the sysfs entry is
read.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Technically there is no need to set the card offline to change
RX checksumming. Get rid of this stupid limitation.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum TSO size OSA can handle is 15 * PAGE_SIZE. This
patch reduces gso_max_size to this value and adds some sanity
checks and statistics to the TSO implementation.
Since only layer 3 is able to do TSO move all TSO related functions
to the qeth_l3 module.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Setting a qeth device online requires to call function
ccw_device_set_online() for read-, write-, and data-subchannel.
Failures should be detected immediately without an attempt to
invoke follow-on activity qeth_qdio_clear_card().,
In addition, ccw_device_set_online calls are consolidated in
qeth_core_main.c only.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
EDDP code has been removed from qeth in 2009. This patch removes two
useless remaining EDDP-references.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Isolate data connection to a shared OSA card against other data
connections to the same OSA card. Connectivity between isolated
data connections sharing the same OSA card is therefore possible only
through external network gear (e.g. a router).
Signed-off-by: Einar Lueck <elelueck@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If ret is unsigned, the checks for negative wm831x_reg_read() return values
are wrong. The error value should be transmitted to its caller, e.g.
wm831x_gp_ldo_get_status() which tests for a negative return value.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
The language of 802.3ad 43.4.9 requires the "recordPDU" function
to, in part, compare the Partner parameter values in a received LACPDU
to the stored Actor values. If those match, then the Partner's
synchronization state is set to true.
The current 802.3ad implementation is performing these steps out
of order; first, the synchronization check is done, then the paramters are
checked to see if they match (the synch check being done against a match
check of a prior LACPDU). This causes delays in establishing aggregators
in some circumstances.
This patch modifies the 802.3ad code to call __choose_matched,
the function that does the "match" comparisions, as the first step of
__record_pdu, instead of immediately afterwards. This new behavior is
in compliance with the language of the standard.
Some additional commentary relating to code vs. standard is also
added.
Reported by Martin Patterson <martin@gear6.com> who also supplied
the logic of the fix and verified the patch.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the NAPI poll function(emac_poll), check for netif_running()
is unnecassary. In addition to associated runtime overhead, it
also results in a continuous softirq loop when the interface is
brought down under heavy traffic(tested wit Traffic Generator).
Once the interface is disabled, the poll function always returns
zero(with the check for netif_running) and napi_complete() would
never get called resulting in softirq loop.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Acked-by: Chaithrika U S <chaithrika@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the NAPI poll function, check for netif_running() is unnecassary.
In addition to associated runtime overhead, it also results in
continuous softirq loop when the interface is brought down under heavy
traffic(tested with Traffic Generator).Once the interface is disabled,
the poll function always returns zero(with the check for netif_running)
and napi_complete() would never get called resulting in softirq loop.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the tg3 version to 3.104.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the 5717 variant device ID enumerations and adds those
DIDs to the PCI ID table.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to funnel each MSI-X vector's rx packet buffers
into a single set of producer rings which will then be submitted to the
hardware.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The rx producer mailbox registers are used in several spots in the code.
The addition of TG3_64BIT_REG_LOW makes register references
uncomfortably long. This patch creates an alias for the standard and
jumbo ring producer index registers to make the code cleaner.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch increases the number of producer rings available and
implements the constructor and destructor code that deals with them.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes how the code uses the rx_std_prod_idx member. In the
following patch, the code will be changed so that it will act just like
a hardware mailbox. This patch prepares the code so that memory barriers
can be more easily inserted.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A later patch is going to add consumer indicies for the producer rings.
To keep things readable, this patch renames rx_[std|jmb]_ptr to
rx_[std|jmb]_prod_idx.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts the tnapi argument of tg3_alloc_rx_skb() to tp. The
level of indirection is unnecessary.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the tg3_alloc_rx_skb() implementation to accept the
destination producer ring set pointer as a parameter rather than
assuming the source and destination producer rings are the same.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes the source index parameter of tg3_alloc_rx_skb(). A
later patch will make it possible for the source and destination
producer rings to be different. This patch opts to make
tg3_alloc_rx_skb() a destination-only implementation and move the code
sensitive to the difference elsewhere.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3_get_invariants(), among other things, discovers whether or not
the device is MSI-X capable and how many interrupts it supports.
This discovery needs to happen before registering NAPI instances with
netdev. This patch moves the code block that calls napi_add later in
tg3_init_one() so that tg3_get_invariants() has a chance to run first.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch gives all non-zero MSIX vectors their own NAPI handler. This
will make NAPI handling for those vectors slightly more efficient.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the 5717 (and future chips) break up PCIe DMA packets across
cacheline boundaries. This isn't necessary on x86. This patch
selectively loosens the restriction.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The A0 revision of the 5717 has problems with short packet fragments.
It needs to use the tg3_start_xmit_dma_bug() routine.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 5717 sets up TSO slightly differently in the transmit path. It
looks like this method will be the new way of doing things. This patch
defines a flag to indicate this.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch consolidates the TSO capability discovery code into its own
code block. The code that decides whether or not to allow TSO is then
cleaned up. Finally, the patch consolidates all MSI and MSIX
capability code into a single code block.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need room for another TSO flag and it would be most efficient if it
resided in tg3_flags2. This patch moves the TG3_FLG2_PROTECTED_NVRAM
to tg3_flags3 to make room.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts tg3_start_xmit_dma_bug() to accomodate multiple NAPI
instances. This is prep work for a later patch in this series.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch avoids reprogramming the RCB NIC addresses for all 5755 and
later devices. The address is incorrect for 5717 devices and should be
correct by default for all other affected devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the 5717 phy ID.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
drop the version parts not needed for in-tree driver
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use device id number directly accompany with
comment rather then a #define
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The returned error should stay negative
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Karsten Keil <keil@b1-systems.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the existing random_ether_addr() to generate random MAC
instead of doing it by-hand.
Signed-off-by: Stanislav O. Bezzubtsev <stas@lvk.cs.msu.su>
Signed-off-by: David S. Miller <davem@davemloft.net>
The version string already contains the printk level
specifying it again results in the following message
being printed:
<6>r6040: RDC R6040 NAPI ...
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
My last commit introduced an typo causing the
compat_ioctl function to do nothing useful.
The obvious way for an ioctl function to work
is to look at the command, not the argument first.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.infradead.org/users/dwmw2/iommu-2.6.32:
intel-iommu: Support PCIe hot-plug
intel-iommu: Obey coherent_dma_mask for alloc_coherent on passthrough
intel-iommu: Check for 'DMAR at zero' BIOS error earlier.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: psmouse - remove unneeded '\n' from psmouse.proto parameter
Input: atkbd - restore LED state at reconnect
Input: force LED reset on resume
Input: fix locking in memoryless force-feedback devices
* 'for-linus' of git://neil.brown.name/md:
md/raid5: Allow dirty-degraded arrays to be assembled when only party is degraded.
Don't unconditionally set in_sync on newly added device in raid5_reshape
md: allow v0.91 metadata to record devices as being active but not in-sync.
md: factor out updating of 'recovery_offset'.
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] s390: fix single stepping on svc0
[S390] sclp: undo quiesce handler override on resume
[S390] reset cputime accounting after IPL from NSS
[S390] monreader: fix use after free bug with suspend/resume
If the waker is killed before it can replay outstanding URBs, these URBs
won't be freed or will be replayed at the next open. This patch closes
the window by explicitely discarding outstanding URBs.
Signed-off-by: Oliver Neukum <oliver@neukum.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Taken from socketcan-svn, fixed remaining todos, cleaned up, tested with a
phyCORE-MPC5200B-IO and a custom board.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
tx_bytes value must be updated by skb length before skb is freed.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The cu3088-driver used as common base for lcs- and ctcm-devices
makes it difficult to assign the appropriate driver to an lcs-device
or a ctcm-device. This patch eliminates the cu3088-driver and thus
the root device "cu3088". Path /sys/devices/cu3088 is replaced with
the pathes /sys/devices/lcs and /sys/devices/ctcm.
Patch is based on a proposal from Cornelia Huck.
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
State transition to DEV_STATE_STOPPED indicates all outstanding I/O has
finished. Add wait queue to wait for this state.
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch pairs similar-numbered Rx and Tx queues onto a single
MSI-X vector. For example, Tx queue 0 and Rx queue 0's interrupt
with be ethX-RxTx-0. This allows for more efficient cleanup, since
fewer interrupts will be firing during device operation. It also
helps with a cleaner CPU affinity for IRQ affinity.
Signed-off-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Shannon Nelson <shannon.nelson@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that we only recycle pages when they are from the
local NUMA node. Non-local pages are freed and replaced with locally
allocated pages.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were previously only checking the first tx ring to see if it had any
packets in it when the link when down. However we should be checking all
of the rings so this patch makes it so that all of the rings are now being
checked.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes unused variables total_tx_bytes, total_tx_packets,
total_rx_bytes, and total_rx_packets from the adapter struct.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does some refactoring work that I felt was needed after reviewing
the changes recently submitted relating to the replacement of net_stats with
netdev->stats.
This patch essentially creates two different collections of stats. The
first handles the adapter specific states and is stored in gstring_stats,
and the second is for netdev specific stats and is stored in
gstring_net_stats.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch makes it so that nics such as 82576 and newer can support more
hardware queues when there are more than 4 cpus by combining a tx/rx queue
pair onto one interrupt so that 8 queue pairs can be supported and thus
allow for more queues.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current code is quite large and making igb_probe difficult to read.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the type for the ring size values to u16 and use min/max_t instead of
min/max.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To fix the bug of checking on signed return value using unsigned statement.
Thanks Roel Kluin for digging out it.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In r8169 driver MTU is used to calculate receive buffer size.
Receive buffer size is used to configure hardware incoming packet filter.
For jumbo frames:
Receive buffer size = Max frame size = MTU + 14 (ethernet header) + 4
(vlan header) + 4 (ethernet checksum) = MTU + 22
Bug:
driver for all MTU up to 1536 use receive buffer size 1536
As you can see from formula, this mean all IP packets > 1536 - 22
(for vlan tagged, 1536 - 18 for not tagged) are dropped by hardware
filter.
Example:
host_good> ifconfig eth0 mtu 1536
host_r8169> ifconfig eth0 mtu 1536
host_good> ping host_r8169
Ok
host_good> ping -s 1500 host_r8169
Fail
host_good> ifconfig eth0 mtu 7000
host_r8169> ifconfig eth0 mtu 7000
host_good> ping -s 1500 host_r8169
Ok
Bonus: got rid of magic number 8
Signed-off-by: Raimonds Cicans <ray@apollo.lv>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the missing "get_xstats_size" callback for the
netlink interface, which is required if "fill_xstats" is used,
as pointed out by Patrick McHardy.
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 2.6.32-rc the new EMS USB CAN driver was contributed and added the Kconfig
entry right behind an entry of the same *vendor*. This teared the SJA1000
based driver selection into pieces.
This fix cleans up the 2.6.32-rc Kconfig files for the CAN drivers and moves
the SJA1000 and USB Kconfig portions into the belonging directories.
As there are many new CAN drivers in the queue getting this cleanup into
2.6.32-rc would massively reduce the problems for the upcoming drivers.
Thanks,
Oliver
Signed-off-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due commit 4b77b0a2ba, it is not more
possible to pci_restore_state() more than once without calling
pci_save_state() in the middle.
Actually running a ethtool test on s2io makes the card inactive,
and it needs to unload/reload the module to fix.
This patch just save the state just after it restore in order to
keep the old behaviour
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix some typos and punctuation in comments
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
[bart: ported the change from the older patch for rt2800usb & rt61pci]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The bit value of AR_GPIO_INPUT_EN_VAL_BT_PRIORITY_BB is wrong, it should
be 0x400 and the number of bits to be right shifted is 10. Having this
wrong value in 0x4054 sometimes affects bt quality on btcoex environment.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Allow rt2800usb to properly detect RT307X based devices, and set the appropriate chipset values.
Signed-off-by: Gertjan van Wingede <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit b8ecd988b1.
Due to poor API call balancing by me, this commit not only broke ipw2200
if it can't find it's firmware, it broke ipw2100 basically anytime you
removed the module. At this point in the cycle, let's just put it back
to a sane state and try again next time...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both vlan and macvlan devices usually don't use a qdisc and immediately
queue packets to the underlying device. Propagate transmission state of
the underlying device to the upper layers so they can react on congestion
and/or inform the sending process.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a system where the ctrl-alt-del init action initiated by signal
quiesce suspends the machine the quiesce handler override for
_machine_restart, _machine_halt and _machine_power_off needs to be
undone, otherwise the override is still present in the resumed
system. The next shutdown would then load the quiesce state psw
instead of performing the correct shutdown action.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The monreader device driver doesn't set dev->driver_data to NULL after
freeing the corresponding data structure. This leads to a use after
free bug in the freeze/thaw suspend/resume functions after the device
has been opened and closed once. Fix this by clearing dev->driver_data
in the close() function.
Signed-off-by: Gerald Schaefer <gerald.schaefer@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The get parameter function should return a string without a life-feed.
Otherwise you'll see additional empty line in sysfs parameters file.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Even though input core tells us to restore LED state and repeat rate
at resume keyboard may be reconnected either by request from userspace
(via sysfs) or just by pulling it from the box and plugging it back in.
In these cases we still need to restore state ourselves.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should be sending EV_LED event down to drivers upon resume even in cases
when in-kernel state of the LED is off since device could come up with some
leds turned on.
Reported-and-tested-by: Mikko Vinni <mmvinni@yahoo.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Normally is it not safe to allow a raid5 that is both dirty and
degraded to be assembled without explicit request from that admin, as
it can cause hidden data corruption.
This is because 'dirty' means that the parity cannot be trusted, and
'degraded' means that the parity needs to be used.
However, if the device that is missing contains only parity, then
there is no issue and assembly can continue.
This particularly applies when a RAID5 is being converted to a RAID6
and there is an unclean shutdown while the conversion is happening.
So check for whether the degraded space only contains parity, and
in that case, allow the assembly.
Signed-off-by: NeilBrown <neilb@suse.de>
When a reshape finds that it can add spare devices into the array,
those devices might already be 'in_sync' if they are beyond the old
size of the array, or they might not if they are within the array.
The first case happens when we change an N-drive RAID5 to an
N+1-drive RAID5.
The second happens when we convert an N-drive RAID5 to an
N+1-drive RAID6.
So set the flag more carefully.
Also, ->recovery_offset is only meaningful when the flag is clear,
so only set it in that case.
This change needs the preceding two to ensure that the non-in_sync
device doesn't get evicted from the array when it is stopped, in the
case where v0.90 metadata is used.
Signed-off-by: NeilBrown <neilb@suse.de>
This is a combination that didn't really make sense before.
However when a reshape is converting e.g. raid5 -> raid6, the extra
device is not fully in-sync, but is certainly active and contains
important data.
So allow that start to be meaningful and in particular get
the 'recovery_offset' value (which is needed for any non-in-sync
active device) from the reshape_position.
Signed-off-by: NeilBrown <neilb@suse.de>
PPS events must be recorded according to PPS's mode settings.
If a process asks for (i.e.) capture-assert events only, when the PPS
client calls the pps_event() function to save the current PPS event, we
should verify the event type and then discard unwanted ones.
Also, without this patch userland processes waiting for a specific PPS
event (assert or clear but not both) may be awakened at wrong time.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: William S. Brasher <billb958@door.net>
Tested-by: Reg Clemens <clemens@dwf.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Userland programs may read/write PPS parameters at same time and these
operations may corrupt PPS data.
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Tested-by: Reg Clemens <clemens@dwf.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
TASK_INTERRUPTIBLE and friends are now only available after including
<linux/sched.h>, so include it when needed.
bus_id is no longer available/necessary, so remove that.
Android pmem driver is not available in mainline, so remove its hooks
from drivers/video.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In case of failure, device_create() returns not NULL but the error code.
The current code checks for non-NULL though which causes kernel oops in
sysfs_create_group() when device_create() fails. Check for error using
IS_ERR() and propagate the error value using PTR_ERR() instead of fixed
-ENODEV code returned now...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
v3020_mmio_read_bit() always returns 0 when left_shift > 7.
v3020_mmio_read_bit()'s return type is (unsigned char). The code returns
a value masked by (1 << left_shift) that is casted to the return type. If
left_shift is larger than 7, the cast will always result in a 0 return
value. The problem was discovered with left_shift = 16, and the included
patch corrects the problem.
The bug was introduced in the last (Apr 3 2009) commit of the file, kernel
versions 2.6.30 and later.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Raphael Assenat <raph@8d.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/rtc/rtc-vr41xx.c: In function 'vr41xx_rtc_irq_set_freq':
drivers/rtc/rtc-vr41xx.c:217: warning: comparison of distinct pointer types lacks a cast
drivers/rtc/rtc-vr41xx.c:217: warning: right shift count >= width of type
drivers/rtc/rtc-vr41xx.c:217: warning: passing argument 1 of '__div64_32' from incompatible pointer type
include/asm-generic/div64.h:35: note: expected 'uint64_t *' but argument is of type 'long unsigned int *'
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The config FB_PRE_INIT_FB entry in drivers/video/Kconfig pushes all entries
below it out of the menuconfig selection. Fix this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This seems to be a different model (with a different PCI ID) than the
"Quatro" card that is also in the list.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
struct uart_port::iobase is unsigned long, so use %lx as printk format
specifier.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
According to Documentation/rtc.txt, RTC_WKALM_SET sets the alarm time and
enables/disables the alarm. We implement RTC_WKALM_SET through
pcf50633_rtc_set_alarm. The enabling/disabling part was missing.
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Reported-by: Michael 'Mickey' Lauer <mickey@openmoko.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The PCF50633 stores a month value of 1-12, but the kernel wants 0-11.
Signed-off-by: Rask Ingemann Lambertsen <rask@sygehus.dk>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
at91sam9g45 non ES lots have an alternate pixel clock calculation formula.
Introduce this one with condition on the cpu_is_xxxxx() macros.
Newer 9g45 SOC will not have good pixel clock calculation without this
fix.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Krzysztof Helt <krzysztof.h1@wp.pl>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix wrong bit mask for blanking register. Due to the error a CRT monitor
blanks off due to wrong frequency (out of range) instead of PM signal
(vertical and horizontal frequencies cut off).
Just compare the mask with bits set in the switch(blank) clause below the
changed line.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove fb_save_state() and fb_restore_state operations from frame buffer layer.
They are used only in two drivers:
1. savagefb - and cause bug #11248
2. uvesafb
Usage of these operations is misunderstood in both drivers so kill these
operations, fix the bug #11248 and avoid confusion in the future.
Tested on Savage 3D/MV card and the patch fixes the bug #11248.
The frame buffer layer uses these funtions during switch between graphics
and text mode of the console, but these drivers saves state before
switching of the frame buffer (in the fb_open) and after releasing it (in
the fb_release). This defeats the purpose of these operations.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=11248
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Reported-by: Jochen Hein <jochen@jochen.org>
Tested-by: Jochen Hein <jochen@jochen.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Michal Januszewski <spock@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for Wake on LAN (WOL) reception and waking the device up from
this signal via the ethtool interface. Currently we are only supporting
the magic-packet variant of wakeup.
WOL is enabled by specifying a second interrupt resource to the driver
which indicates where the interrupt for the WOL is being signalled. This
then enables the necessary ethtool calls to leave the device in a state
to receive WOL frames when going into suspend.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The values of r_idx and rx_ring are not used after the last time they
are set in ixgbe_msix_clean_rx(), so they can be removed.
Signed-off-by: Ali Gholami Rudi <ali@rudi.ir>
Acked-by: Peter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not need to change the frame routing to direct all frames to the
management fifo during suspend. This is now done by the firmware.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before calling gfar_clean_tx_ring() the driver grabs an irqsave
spinlock, and then tries to recycle skbs. But since
skb_recycle_check() returns 0 with IRQs disabled, we'll never
recycle any skbs.
It appears that gfar_clean_tx_ring() and gfar_start_xmit() are
mostly idependent and can work in parallel, except when they
modify num_txbdfree.
So we can drop the lock from most sections and thus fix the skb
recycling.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
gfar_error() can arrive at the middle of gfar_start_xmit() processing,
and so it can trigger transfers of BDs that we don't yet expect to
be transmitted.
Fix this by locking the tx queues in gfar_error().
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We obviously want to write a modified 'temp' value back to the
register, not the saved IRQ flags.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit fba4ed030c ("gianfar: Add Multiple
Queue Support") introduced the following build failure:
CC gianfar.o
gianfar.c: In function 'gfar_restore':
gianfar.c:1249: error: request for member 'napi' in something not a structure or union
This patch fixes the issue.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is OK to poll with disabled IRQs, so remove the warning.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support PCIe hot plug in IOMMU, we register a notifier to respond to device
change action.
When the notifier gets BUS_NOTIFY_UNBOUND_DRIVER, it removes the device
from its DMAR domain.
A hot added device will be added into an IOMMU domain when it first does IOMMU
op. So there is no need to add more code for hot add.
Without the patch, after a hot-remove, a hot-added device on the same
slot will not work.
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Tested-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The model for IOMMU passthrough is that decent devices that can cope
with DMA to all of memory get passthrough; crappy devices with a limited
dma_mask don't -- they get to use the IOMMU anyway.
This is done on the basis that IOMMU passthrough is usually wanted for
performance reasons, and it's only the decent PCI devices that you
really care about performance for, while the crappy 32-bit ones like
your USB controller can just use the IOMMU and you won't really care.
Unfortunately, the check for this was only looking at dev->dma_mask, not
at dev->coherent_dma_mask. And some devices have a 32-bit
coherent_dma_mask even though they have a full 64-bit dma_mask.
Even more unfortunately, fixing that simple oversight would upset
certain broken HP devices. Not only do they have a 32-bit
coherent_dma_mask, but they also have a tendency to do stray DMA to
unmapped addresses. And then they die when they take the DMA fault they
so richly deserve.
So if we do the 'correct' fix, it'll mean that affected users have to
disable IOMMU support completely on "a large percentage of servers from
a major vendor."
Personally, I have little sympathy -- given that this is the _same_
'major vendor' who is shipping machines which claim to have IOMMU
support but have obviously never _once_ booted a VT-d capable OS to do
any form of QA. But strictly speaking, it _would_ be a regression even
though it only ever worked by fluke.
For 2.6.33, we'll come up with a quirk which gives swiotlb support
for this particular device, and other devices with an inadequate
coherent_dma_mask will just get normal IOMMU mapping.
The simplest fix for 2.6.32, though, is just to jump through some hoops
to try to allocate coherent DMA memory for such devices in a place that
they can reach. We'd use dma_generic_alloc_coherent() for this if it
existed on IA64.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Each device has its own 'recovery_offset' showing how far
recovery has progressed on the device.
As the only real significance of this is that fact that it can
be stored in the metadata and recovered at restart, and as
only 1.x metadata can do this, we were only updating
'recovery_offset' to 'curr_resync_completed' when updating
v1.x metadata.
But this is wrong, and we will shortly make limited use of this
field in v0.90 metadata.
So move the update into common code.
Signed-off-by: NeilBrown <neilb@suse.de>
Fix a type in rt2800_config_channel_rt3x. The second write to RF
register 2 should be to RF register 3. This is confirmed by the
legacy Ralink code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
fix some typos and punctuation in comments
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For my Linksys WUSB11 at76c503-i3861 device, scanning fails without
probe_delay, min_channel_time, and max_channel_time specified for the
scan request. These values were found by checking scan requests from
the at76_usb driver.
Signed-off-by: Jason Andryuk <jandryuk@gmail.com>
Acked-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As mentioned on the linux-wireless mailing list, the current copyright
statements in the rt2x00 are meaningless, as the rt2x00 project is
not even a formal legal entity. Therefore it is better to replace
the existing copyright statements with copyright statements for the
people that actually wrote the code.
Note: Updated to the best of my knowledge with respect to who
contributed considerable amounts of code.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
CC: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Link tuning code from the legacy rt2570 driver turned out to be
harmful and got disabled by the commit d06193f ("rt2x00: Disable
link tuning in rt2500usb") in August 2008.
There is no reason to keep this dead code any longer so remove it
(it can still be retrieved from the git history if necessary).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is needed for at least RT3070 chip.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
eFuse EEPROM is used also by USB chips (i.e. RT3070)
so move the needed code from rt2800pci to rt2800lib.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename RXD_W0_* defines to RXINFO_W0_* ones to match naming
used for TX descriptor and by the vendor driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add rf_vals tables and rt2800_probe_hw_mode() to rt2800lib.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enclose interface specific code in rt2800[pci,usb]_probe_hw_mode()
with rt2x00_intf_is_[pci,usb]() checks.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move hw_mode information initialization code block before
HT information initialization one to match the ordering used
by rt2800pci's rt2800pci_probe_hw_mode().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2800pci's rf_vals[] copy was missing values for some channels.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add rt2800_validate_eeprom() and rt2800_init_eeprom() to rt2800lib.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Factor out common code from rt2800[pci,usb]_validate_eeprom()
to rt2800_validate_eeprom().
* Fix interface specific comment in rt2800[pci,usb]_validate_eeprom().
* Enclose interface specific code in rt2800[pci,usb]_init_eeprom()
with rt2x00_intf_is_[pci,usb]() checks.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_rx_status->qual has been marked deprecated.
This allows us to remove several functions and fields which
were used to calculate a reasonable value for it.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of assuming that all rt3090 devices will have an eFuse EEPROM,
do as the legacy Ralink driver, and detect at run-time whether an
eFuse EEPROM is present.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jumbograms are frames put together linked together through
more than one descriptor. For example ath9k_htc will use this
to send from the target a large frame split up into 2 or more
segments. The driver then would be in charge of putting the
frame back together.
When jumbograms are constructed the rx_stats->rs_more will
bet set and rx_stats->rs_status will not have any valid content
as the actual status will only be avialable at the end of
the chained descriptors.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is now deprecated and unused within mac80211, so time
to remove it as otherwise we'd be doing some unecessary
computations for nothing.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k and ath9k_htc share a lot of common hardware characteristics.
They only differ in that ath9k_htc works with a target CPU and ath9k
works directly with the hardware. ath9k_htc will do *some* things in
the firmware, but a lot of others on the host.
The common 802.11n hardware code is already shared through the ath9k_hw
module. Common helpers amongst all Atheros drivers can use the ath module,
this includes ath5k and ar9170 as users. But there is some common driver
specific helpers which are not exactly hardware code which ath9k and
ath9k_htc can share. We'll be using ath9k_common for this to avoid
bloating the ath module and the common 802.11n hardware module ath9k_hw.
We start by sharing skb pre and post processing in preparation for a hand
off to mac80211.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a helper for the RX skb post processing,
ath9k_rx_skb_postprocess().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will make sharing code easier between ath9k and ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
And change the return value to something more obvious.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While at it flip the order, seems easier to read and also
add some better description as to why we do this check.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath5k is using the (csz - 1) twice as ath_rxbuf_alloc() already allocates
and moves skb->data accordingly. Remove the extra (csz -1).
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will also be used by ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The skb->cb (control buffer, 48 bytes) is available to the skb
upon skb allocation. You can fill it up imediately after skb
allocation. ath9k was copying onto the skb->cb the data from the
processed skb for mac80211 from a stack struct ieee80211_rx_status
structure. This is unnecessary, instead use the skb->cb for the
rx status immediately after the skb becomes available and DMA
synched.
Additionally, avoid the copy of the skb->cb also for virtual wiphys
as skb_copy() will copy over the skb->cb for us as well.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves all the RX processing of RSSI into a helper,
ath_rx_prepare(). ath_rx_prepare() should now be really
easy to read and follow.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This moves the qual computing into a small helper,
ath9k_compute_qual()
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_process_rate() now does all the rx status processing to
read the rate the hardware passed and translate it to whatever
mac80211 wants.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its just a distraction when reading the code, instead use the
rx_stats->rs_rate directly.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This does sanity checking on the skb and RX status descriptor
prior to processing.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to use the private driver structure to get to an sband.
This will make it easier to share this code with ath9k_htc.
With the sc gone we can now just pass the common structure to
ath_rx_prepare().
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This can be shared between ath9k and ath9k_htc. It will also
help with sharing routine helpers on the RX path.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This will be shared between ath9k and ath9k_htc.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Its not needed, so just pass the hardware RX status.
We'll be simplfying ath_rx_prepare() with code we can share
between ath9k and ath9k_htc. This will help make that code
easier to read and manage.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k virtual wiphys all share the same internal buffer space
for TX but they do not share the mac80211 skb queues. When
ath9k detects it is running low on buffer space to TX it tells
mac80211 to stop sending it skbs its way but it always does
this only for the primary wiphy. This means mac80211 won't know
its best to avoid sending ath9k more skbs on a separate virtual
wiphy. The same issue is present for reliving the skb queue.
Since ath9k does not keep track of which virtual wiphy is hammering
on TX silence all wiphy's TX when we're low on buffer space. When
we're free on buffer space only bother informing the virtual wiphy
which is active that we have free buffers.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using virtual wiphys the base sc->hw was being used, the correct
hw is passed along the caller already so just use that.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ath9k virtual wiphys are used the sc->hw will not always represent
the active hw, instead we need to get it from the skb->cb private
driver area. This ensures the right hw is used to find a sta for
the TX'd skb.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We use the ieee80211_hw for radio enable/disable but the wrong
structure hw was being used in consideration for virtual wiphys
as each virtual wiphy has its own ieee80211_hw struct.
Just pass the hw struct to ensure we use the right one. This should
fix the hw used and passed for radio enable/disable. This includes
the stoping / starting of the software TX queues so mac80211 doesn't
send us data for a specific virtual wiphy. ath9k already takes care
of pausing virtual wiphys and stopping the respective queues on its
own, but this should handle the idle mac80211 conf calls as well.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this now uses the proper hw which should mean finding the
right sta when using ath9k virtual wiphy stuff. Only
advantage I see here is getting the rssi properly updated
so the 'fix' itself isn't that great, but at least this
is correct.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath_get_virt_hw() is required on RX to determine for which virtual
wiphy an skb came in for. Instead of searching for the hw twice do
it only once.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k supports its own virtual wiphys. The hardware code
relies on the ieee80211_hw for the present interface but
with recent changes introduced the common->hw was never
updated and is required for virtual wiphys.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The way idle configuration detection was implemented as
busted due to the fact that it assumed the ath9k virtual wiphy,
the aphy, would be marked as inactive if it was not used but
it turns out an aphy is always active if its the only wiphy
present. We need to distinguish between aphy activity and
idleness so we now add an idle bool for the aphy and mark
it as such based on the passed IEEE80211_CONF_CHANGE_IDLE
from mac80211.
Previous to all_wiphys_idle would never be true when using
only one device so we never really were using
IEEE80211_CONF_CHANGE_IDLE -- we never turned the radio
off or on upon IEEE80211_CONF_CHANGE_IDLE changes as radio
changes depended on all_wiphys_idle being true either to
turn the radio on or off. Since it was always false for
one device this code was doing nothing.
Cc: Jouni.Malinen <Jouni.Malinen@atheros.com>
Reported-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rafael debugged a resume-time hang (with oopses in workqueue handling)
on his laptop that was due to the 'waker' workqueue entry being
disconnected and then released without the workqueue entry having been
synchronized.
Several people were involved, with Oleg Nesterov doing a debugging patch
showing what workqueue entry was corrupt etc.
This was a regression introduced by commit 7bee549e19 ("Bluetooth: Add
USB autosuspend support to btusb driver") as Rafael points out (not
actually bisected, but it became clear once the bug was found).
Tested-and-reported-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Oliver Neukum <oliver@neukum.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I may have botched my merge conflict resolution instructions for Dave...
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When enabling rt2800usb as a built-in driver (as opposed to a as a module) the build fails. See
http://marc.info/?l=linux-wireless&m=125768687711034&w=2 for details.
Fix it by properly including <linux/usb.h> from rt2x00usb.h
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make sure all drivers can benefit of the assignment of the interface
type of an adapter, instead of keeping it for rt2800 only.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CCS_START_NETWORK is declared in drivers/net/wireless/rayctl.h with the
comment Values for cmd. status is previously compared to
CCS_COMMAND_COMPLETE, which is declared in the same file with the comment
Values for buffer_status. Finally, it is possible at this point that cmd
is CCS_START_NETWORK, because it is compared to that value in an enclosing
switch that has CCS_START_NETWORK as one of two case labels around this code.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes the RX error path for rev>=8 devices.
The wrong register size and definitions were used.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These wireless drivers in staging could be built when
CONFIG_NET=n, CONFIG_NETDEVICES=n, causing this build error:
net/wireless/wext-priv.c: In function 'ioctl_private_call':
net/wireless/wext-priv.c:206: error: implicit declaration of function 'call_commit_handler'
due to faulty selects.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add txq_id info to "Tx queue requesting wakeup" debug message
Add "Rx queue requesting wakeup" debug message
Move clear of CSR_GP_CNTRL_REG_FLAG_MAC_ACCESS_REQ to be after nearby
iwl_write_prph(), since iwl_write_prph() sets it and clears it. Almost
removed it entirely, but just making sure in case someone removes the
iwl_write_prph()! Also remove unneeded priv->lock usage; this is now
handled by priv->reg_lock within iwl_clear_bit().
Join a couple of lines that had unneeded line returns.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Turn on RTS/CTS for HT to prevent uCode TX fifo underrun
This is fix for
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=2103
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Tested-by: Jiajia Zheng <jiajia.zheng@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Follow-up to "update write pointers for all tx queues after wakeup"; that
patch changed iwl_irq_tasklet_legacy(), but not iwl_irq_tasklet(), so
newer devices were not covered.
Comments from original patch:
Wakeup interrupt has been updating write pointers (indexes, actually) only
for tx queues 0-5. This is adequate just for 3945, but inadequate for other
devices, all of which have more tx queues. Now updating all tx/command queues,
so device can be aware of all new tx and host commands enqueued while
device was asleep.
This can potentially improve data traffic bandwidth and/or latency.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Take advantage of device's auto-increment for SRAM reads to eliminate extra
write address accesses.
Grab/release NIC access before/after entire read sequence, rather than for
each read individually.
After a quick check of dmesg logs, this seems to double Event Log dump speed,
reducing from about 20 milliseconds to about 10 milliseconds for 512 entries
using 3945.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If device provides bad values for Event Log parameters (due to being asleep
or SRAM corruption, etc.), the size can be very, very large (e.g. 0xa5a5a5a5),
which can flood system log.
Sanity-check capacity and next_entry values and limit to reasonable size dump.
Signed-off-by: Ben Cahill <ben.m.cahill@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Do not use AP's SM_PS setting for our own SM_PS setting.
Reported-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the support for all the PCI_IDs never make into production
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
