A bg that's been flagged "corrupt" by definition has no free blocks,
so that the allocator won't be tempted to use the damaged bg.
Therefore, we shouldn't count the clusters in the damaged group when
calculating free counts.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Zheng Liu <wenqing.lz@taobao.com>
If the group descriptor fails validation, mark the whole blockgroup
corrupt so that the inode/block allocators skip this group. The
previous approach takes the risk of writing to a damaged group
descriptor; hopefully it was never the case that the [ib]bitmap fields
pointed to another valid block and got dirtied, since the memset would
fill the page with 1s.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When we notice a block-bitmap corruption (because of device failure or
something else), we should mark this group as corrupt and prevent
further block allocations/deallocations from it. Currently, we end up
generating one error message for every block in the bitmap. This
potentially could make the system unstable as noticed in some
bugs. With this patch, the error will be printed only the first time
and mark the entire block group as corrupted. This prevents future
access allocations/deallocations from it.
Also tested by corrupting the block
bitmap and forcefully introducing the mb_free_blocks error:
(1) create a largefile (2Gb)
$ dd if=/dev/zero of=largefile oflag=direct bs=10485760 count=200
(2) umount filesystem. use dumpe2fs to see which block-bitmaps
are in use by largefile and note their block numbers
(3) use dd to zero-out the used block bitmaps
$ dd if=/dev/zero of=/dev/hdc4 bs=4096 seek=14 count=8 oflag=direct
(4) mount the FS and delete the largefile.
(5) recreate the largefile. verify that the new largefile does not
get any blocks from the groups marked as bad.
Without the patch, we will see mb_free_blocks error for each bit in
each zero'ed out bitmap at (4). With the patch, we only see the error
once per blockgroup:
[ 309.706803] EXT4-fs error (device sdb4): ext4_mb_generate_buddy:735: group 15: 32768 clusters in bitmap, 0 in gd. blk grp corrupted.
[ 309.720824] EXT4-fs error (device sdb4): ext4_mb_generate_buddy:735: group 14: 32768 clusters in bitmap, 0 in gd. blk grp corrupted.
[ 309.732858] EXT4-fs error (device sdb4) in ext4_free_blocks:4802: IO failure
[ 309.748321] EXT4-fs error (device sdb4): ext4_mb_generate_buddy:735: group 13: 32768 clusters in bitmap, 0 in gd. blk grp corrupted.
[ 309.760331] EXT4-fs error (device sdb4) in ext4_free_blocks:4802: IO failure
[ 309.769695] EXT4-fs error (device sdb4): ext4_mb_generate_buddy:735: group 12: 32768 clusters in bitmap, 0 in gd. blk grp corrupted.
[ 309.781721] EXT4-fs error (device sdb4) in ext4_free_blocks:4802: IO failure
[ 309.798166] EXT4-fs error (device sdb4): ext4_mb_generate_buddy:735: group 11: 32768 clusters in bitmap, 0 in gd. blk grp corrupted.
[ 309.810184] EXT4-fs error (device sdb4) in ext4_free_blocks:4802: IO failure
[ 309.819532] EXT4-fs error (device sdb4): ext4_mb_generate_buddy:735: group 10: 32768 clusters in bitmap, 0 in gd. blk grp corrupted.
Google-Bug-Id: 7258357
[darrick.wong@oracle.com]
Further modifications (by Darrick) to make more obvious that this corruption
bit applies to blocks only. Set the corruption flag if the block group bitmap
verification fails.
Original-author: Aditya Kali <adityakali@google.com>
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The block_group parameter to ext4_validate_block_bitmap is both used
as a ext4_group_t inside the function and the same type is passed in
by all callers. We might as well use the typedef consistently instead
of open-coding the 'unsigned int'.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The block bitmap verification code assumes that calling ext4_error()
either panics the system or makes the fs readonly. However, this is
not always true: when 'errors=continue' is specified, an error is
printed but we don't return any indication of error to the caller,
which is (probably) the block allocator, which pretends that the crud
we read in off the disk is a usable bitmap. Yuck.
A block bitmap that fails the check should at least return no bitmap
to the caller. The block allocator should be told to go look in a
different group, but that's a separate issue.
The easiest way to reproduce this is to modify bg_block_bitmap (on a
^flex_bg fs) to point to a block outside the block group; or you can
create a metadata_csum filesystem and zero out the block bitmaps.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The test_root() function could potentially loop forever due to
overflow issues. So rewrite test_root() to avoid this issue; as a
bonus, it is 38% faster when benchmarked via a test loop:
int main(int argc, char **argv)
{
int i;
for (i = 0; i < 1 << 24; i++) {
if (test_root(i, 7))
printf("%d\n", i);
}
}
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
As Dave Chinner pointed out at the 2013 LSF/MM workshop, it's
important that metadata I/O requests are marked as such to avoid
priority inversions caused by I/O bandwidth throttling.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Currently in ENOSPC condition when writing into unwritten space, or
punching a hole, we might need to split the extent and grow extent tree.
However since we can not allocate any new metadata blocks we'll have to
zero out unwritten part of extent or punched out part of extent, or in
the worst case return ENOSPC even though use actually does not allocate
any space.
Also in delalloc path we do reserve metadata and data blocks for the
time we're going to write out, however metadata block reservation is
very tricky especially since we expect that logical connectivity implies
physical connectivity, however that might not be the case and hence we
might end up allocating more metadata blocks than previously reserved.
So in future, metadata reservation checks should be removed since we can
not assure that we do not under reserve.
And this is where reserved space comes into the picture. When mounting
the file system we slice off a little bit of the file system space (2%
or 4096 clusters, whichever is smaller) which can be then used for the
cases mentioned above to prevent costly zeroout, or unexpected ENOSPC.
The number of reserved clusters can be set via sysfs, however it can
never be bigger than number of free clusters in the file system.
Note that this patch fixes the failure of xfstest 274 as expected.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Carlos Maiolino <cmaiolino@redhat.com>
Currently on many places in ext4 we're using
ext4_get_group_no_and_offset() even though we're only interested in
knowing the block group of the particular block, not the offset within
the block group so we can use more efficient way to compute block
group.
This patch introduces ext4_get_group_number() which computes block
group for a given block much more efficiently. Use this function
instead of ext4_get_group_no_and_offset() everywhere where we're only
interested in knowing the block group.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Currently in when getting the block group number for a particular
block in ext4_block_in_group() we're using
ext4_get_group_no_and_offset() which uses do_div() to get the block
group and the remainer which is offset within the group.
We don't need all of that in ext4_block_in_group() as we only need to
figure out the group number.
This commit changes ext4_block_in_group() to calculate group number
directly. This shows as a big improvement with regards to cpu
utilization. Measuring fallocate -l 15T on fresh file system with perf
showed that 23% of cpu time was spend in the
ext4_get_group_no_and_offset(). With this change it completely
disappears from the list only bumping the occurrence of
ext4_init_block_bitmap() which is the biggest user of
ext4_block_in_group() by 4%. As the result of this change on my system
the fallocate call was approx. 10% faster.
However since there is '-g' option in mkfs which allow us setting
different groups size (mostly for developers) I've introduced new per
file system flag whether we have a standard block group size or
not. The flag is used to determine whether we can use the bit shift
optimization or not.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We're using macro EXT4_B2C() to convert number of blocks to number of
clusters for bigalloc file systems. However, we should be using
EXT4_NUM_B2C().
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
ext4_has_free_clusters() should tell us whether there is enough free
clusters to allocate, however number of free clusters in the file system
is converted to blocks using EXT4_C2B() which is not only wrong use of
the macro (we should have used EXT4_NUM_B2C) but it's also completely
wrong concept since everything else is in cluster units.
Moreover when calculating number of root clusters we should be using
macro EXT4_NUM_B2C() instead of EXT4_B2C() otherwise the result might be
off by one. However r_blocks_count should always be a multiple of the
cluster ratio so doing a plain bit shift should be enough here. We
avoid using EXT4_B2C() because it's confusing.
As a result of the first problem number of free clusters is much bigger
than it should have been and ext4_has_free_clusters() would return 1 even
if there is really not enough free clusters available.
Fix this by removing the EXT4_C2B() conversion of free clusters and
using bit shift when calculating number of root clusters. This bug
affects number of xfstests tests covering file system ENOSPC situation
handling. With this patch most of the ENOSPC problems with bigalloc file
system disappear, especially the errors caused by delayed allocation not
having enough space when the actual allocation is finally requested.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
In mke2fs, we only checksum the whole bitmap block and it is right.
While in the kernel, we use EXT4_BLOCKS_PER_GROUP to indicate the
size of the checksumed bitmap which is wrong when we enable bigalloc.
The right size should be EXT4_CLUSTERS_PER_GROUP and this patch fixes
it.
Also as every caller of ext4_block_bitmap_csum_set and
ext4_block_bitmap_csum_verify pass in EXT4_BLOCKS_PER_GROUP(sb)/8,
we'd better removes this parameter and sets it in the function itself.
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Lukas Czerner <lczerner@redhat.com>
Cc: stable@vger.kernel.org
While in ext4_validate_block_bitmap(), if an block allocation bitmap
is found to be invalid, we call ext4_error() while the block group is
still locked. This causes ext4_commit_super() to call a function
which might sleep while in an atomic context.
There's no need to keep the block group locked at this point, so hoist
the ext4_error() call up to ext4_validate_block_bitmap() and release
the block group spinlock before calling ext4_error().
The reported stack trace can be found at:
http://article.gmane.org/gmane.comp.file-systems.ext4/33731
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
Make it possible for ext4_count_free to operate on buffers and not
just data in buffer_heads.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Ext3 filesystems that are converted to use as many ext4 file system
features as possible will enable uninit_bg to speed up e2fsck times.
These file systems will have a native ext3 layout of inode tables and
block allocation bitmaps (as opposed to ext4's flex_bg layout).
Unfortunately, in these cases, when first allocating a block in an
uninitialized block group, ext4 would incorrectly calculate the number
of free blocks in that block group, and then errorneously report that
the file system was corrupt:
EXT4-fs error (device vdd): ext4_mb_generate_buddy:741: group 30, 32254 clusters in bitmap, 32258 in gd
This problem can be reproduced via:
mke2fs -q -t ext4 -O ^flex_bg /dev/vdd 5g
mount -t ext4 /dev/vdd /mnt
fallocate -l 4600m /mnt/test
The problem was caused by a bone headed mistake in the check to see if a
particular metadata block was part of the block group.
Many thanks to Kees Cook for finding and bisecting the buggy commit
which introduced this bug (commit fd034a84e1, present since v3.2).
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Reported-by: Kees Cook <keescook@chromium.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Tested-by: Kees Cook <keescook@chromium.org>
Cc: stable@kernel.org
The major new feature added in this update is Darrick J. Wong's
metadata checksum feature, which adds crc32 checksums to ext4's
metadata fields. There is also the usual set of cleanups and bug
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=SdJJ
-----END PGP SIGNATURE-----
Merge tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4
Pull Ext4 updates from Theodore Ts'o:
"The major new feature added in this update is Darrick J Wong's
metadata checksum feature, which adds crc32 checksums to ext4's
metadata fields.
There is also the usual set of cleanups and bug fixes."
* tag 'ext4_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tytso/ext4: (44 commits)
ext4: hole-punch use truncate_pagecache_range
jbd2: use kmem_cache_zalloc wrapper instead of flag
ext4: remove mb_groups before tearing down the buddy_cache
ext4: add ext4_mb_unload_buddy in the error path
ext4: don't trash state flags in EXT4_IOC_SETFLAGS
ext4: let getattr report the right blocks in delalloc+bigalloc
ext4: add missing save_error_info() to ext4_error()
ext4: add debugging trigger for ext4_error()
ext4: protect group inode free counting with group lock
ext4: use consistent ssize_t type in ext4_file_write()
ext4: fix format flag in ext4_ext_binsearch_idx()
ext4: cleanup in ext4_discard_allocated_blocks()
ext4: return ENOMEM when mounts fail due to lack of memory
ext4: remove redundundant "(char *) bh->b_data" casts
ext4: disallow hard-linked directory in ext4_lookup
ext4: fix potential integer overflow in alloc_flex_gd()
ext4: remove needs_recovery in ext4_mb_init()
ext4: force ro mount if ext4_setup_super() fails
ext4: fix potential NULL dereference in ext4_free_inodes_counts()
ext4/jbd2: add metadata checksumming to the list of supported features
...
metadata_csum supersedes uninit_bg. Convert the ROCOMPAT uninit_bg
flag check to a helper function that covers both, and make the
checksum calculation algorithm use either crc16 or the metadata_csum
chosen algorithm depending on which flag is set. Print a warning if
we try to mount a filesystem with both feature flags set.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Compute and verify the checksum of the block bitmap; this checksum is
stored in the block group descriptor.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Get rid of this one:
fs/ext4/balloc.c: In function 'ext4_wait_block_bitmap':
fs/ext4/balloc.c:405:3: warning: format '%llu' expects argument of
type 'long long unsigned int', but argument 6 has type 'sector_t' [-Wformat]
Happens because sector_t is u64 (unsigned long long) or unsigned long
dependent on CONFIG_64BIT.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
In ext4_read_{inode,block}_bitmap() we were setting bitmap_uptodate()
before submitting the buffer for read. The is bad, since we check
bitmap_uptodate() without locking the buffer, and so if another
process is racing with us, it's possible that they will think the
bitmap is uptodate even though the read has not completed yet,
resulting in inodes and blocks potentially getting allocated more than
once if we get really unlucky.
Addresses-Google-Bug: 2828254
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
A couple more functions can reasonably be made static if desired.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
sbi is not defined, so let ext4_free_blocks use EXT4_SB(sb) instead
when EXT4FS_DEBUG is defined.
Signed-off-by: Yongqiang Yang <xiaoqiangnk@gmail.com>
Rename the function so it is more clear what is going on. Also rename
the various variables so it's clearer what's happening.
Also fix a missing blocks to cluster conversion when reading the
number of reserved blocks for root.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This function really claims a number of free clusters, not blocks, so
rename it so it's clearer what's going on.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This function really returns the number of clusters after initializing
an uninitalized block bitmap has been initialized.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This function really counts the free clusters reported in the block
group descriptors, so rename it to reduce confusion.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The field bg_free_blocks_count_{lo,high} in the block group
descriptor has been repurposed to hold the number of free clusters for
bigalloc functions. So rename the functions so it makes it easier to
read and audit the block allocation and block freeing code.
Note: at this point in bigalloc development we doesn't support
online resize, so this also makes it really obvious all of the places
we need to fix up to add support for online resize.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
With bigalloc changes, the i_blocks value was not correctly set (it was still
set to number of blocks being used, but in case of bigalloc, we want i_blocks
to represent the number of clusters being used). Since the quota subsystem sets
the i_blocks value, this patch fixes the quota accounting and makes sure that
the i_blocks value is set correctly.
Signed-off-by: Aditya Kali <adityakali@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Convert the percpu counters s_dirtyblocks_counter and
s_freeblocks_counter in struct ext4_super_info to be
s_dirtyclusters_counter and s_freeclusters_counter.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Certain parts of the ext4 code base, primarily in mballoc.c, use a
block group number and offset from the beginning of the block group.
This offset is invariably used to index into the allocation bitmap, so
change the offset to be denominated in units of clusters.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The function ext4_free_blocks_after_init() used to be a #define of
ext4_init_block_bitmap(). This actually made it difficult to
understand how the function worked, and made it hard make changes to
support clusters. So as an initial cleanup, I've separated out the
functionality of initializing block bitmap from calculating the number
of free blocks in the new block group.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This makes it easier to understand how ext4_init_block_bitmap() works,
and it will assist when we split out ext4_free_blocks_after_init() in
the next commit.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
I found that ext4_ext_find_goal() and ext4_find_near()
share the same code for returning a coloured start block
based on i_block_group.
We can refactor this into a common function so that they
don't diverge in the future.
Thanks to adilger for suggesting the new function name.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch adds an allocation request flag to the ext4_has_free_blocks
function which enables the use of reserved blocks. This will allow a
punch hole to proceed even if the disk is full. Punching a hole may
require additional blocks to first split the extents.
Because ext4_has_free_blocks is a low level function, the flag needs
to be passed down through several functions listed below:
ext4_ext_insert_extent
ext4_ext_create_new_leaf
ext4_ext_grow_indepth
ext4_ext_split
ext4_ext_new_meta_block
ext4_mb_new_blocks
ext4_claim_free_blocks
ext4_has_free_blocks
[ext4 punch hole patch series 1/5 v7]
Signed-off-by: Allison Henderson <achender@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reviewed-by: Mingming Cao <cmm@us.ibm.com>
In preparation for the next patch, the function ext4_add_groupblocks()
is moved to mballoc.c, where it could use some static functions.
Signed-off-by: Amir Goldstein <amir73il@users.sf.net>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
percpu_counter_sum_positive() never returns a negative value.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
- Add more ext4 tracepoints.
- Change ext4 tracepoints to use dev_t field with MAJOR/MINOR macros
so that we can save 4 bytes in the ring buffer on some platforms.
- Add sync_mode to ext4_da_writepages, ext4_da_write_pages, and
ext4_da_writepages_result tracepoints. Also remove for_reclaim
field from ext4_da_writepages since it is usually not very useful.
Signed-off-by: Jiaying Zhang <jiayingz@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Remove the short element i_delalloc_reserved_flag from the
ext4_inode_info structure and replace it a new bit in i_state_flags.
Since we have an ext4_inode_info for every ext4 inode cached in the
inode cache, any savings we can produce here is a very good thing from
a memory utilization perspective.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
These functions have no need to be exported beyond file context.
No functions needed to be moved for this commit; just some function
declarations changed to be static and removed from header files.
(A similar patch was submitted by Eric Sandeen, but I wanted to handle
code movement in separate patches to make sure code changes didn't
accidentally get dropped.)
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We don't need to set s_dirt in most of the ext4 code when journaling
is enabled. In ext3/4 some of the summary statistics for # of free
inodes, blocks, and directories are calculated from the per-block
group statistics when the file system is mounted or unmounted. As a
result the superblock doesn't have to be updated, either via the
journal or by setting s_dirt. There are a few exceptions, most
notably when resizing the file system, where the superblock needs to
be modified --- and in that case it should be done as a journalled
operation if possible, and s_dirt set only in no-journal mode.
This patch will optimize out some unneeded disk writes when using ext4
with a journal.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Because we can badly over-reserve metadata when we
calculate worst-case, it complicates things for quota, since
we must reserve and then claim later, retry on EDQUOT, etc.
Quota is also a generally smaller pool than fs free blocks,
so this over-reservation hurts more, and more often.
I'm of the opinion that it's not the worst thing to allow
metadata to push a user slightly over quota. This simplifies
the code and avoids the false quota rejections that result
from worst-case speculation.
This patch stops the speculative quota-charging for
worst-case metadata requirements, and just charges quota
when the blocks are allocated at writeout. It also is
able to remove the try-again loop on EDQUOT.
This patch has been tested indirectly by running the xfstests
suite with a hack to mount & enable quota prior to the test.
I also did a more specific test of fragmenting freespace
and then doing a large delalloc write under quota; quota
stopped me at the right amount of file IO, and then the
writeout generated enough metadata (due to the fragmentation)
that it put me slightly over quota, as expected.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There are duplicate macro definitions of in_range() in mballoc.h and
balloc.c. This consolidates these two definitions into ext4.h, and
changes extents.c to use in_range() as well.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andreas Dilger <adilger@sun.com>
This is a cleanup and simplification patch which takes some open-coded
calculations to calculate the first block number of a group and
converts them to use the (already defined) ext4_group_first_block_no()
function.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andreas Dilger <adilger@sun.com>
Just a pet peeve of mine; we had a mishash of calls with either __func__
or "function_name" and the latter tends to get out of sync.
I think it's easier to just hide the __func__ in a macro, and it'll
be consistent from then on.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
ext4_mb_free_blocks() is only called by ext4_free_blocks(), and the
latter function doesn't really do much. So merge the two functions
together, such that ext4_free_blocks() is now found in
fs/ext4/mballoc.c. This saves about 200 bytes of compiled text space.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The number of old-style block group descriptor blocks is
s_meta_first_bg when the meta_bg feature flag is set.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
ext4_mb_update_group_info is only called in one place, and it's
extremely simple. There's no reason to have it in a separate function
in a separate file as far as I can tell, it just obfuscates what's
really going on.
Perhaps it was intended to keep the grp->bb_* manipulation local to
mballoc.c but we're already accessing other grp-> fields in balloc.c
directly so this seems ok.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We have sb_bgl_lock() and ext4_group_info.bb_state
bit spinlock to protech group information. The later is only
used within mballoc code. Consolidate them to use sb_bgl_lock().
This makes the mballoc.c code much simpler and also avoid
confusion with two locks protecting same info.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Ext4's on-line resizing adds a new block group and then, only at the
last step adjusts s_groups_count. However, it's possible on SMP
systems that another CPU could see the updated the s_group_count and
not see the newly initialized data structures for the just-added block
group. For this reason, it's important to insert a SMP read barrier
after reading s_groups_count and before reading any (for example) the
new block group descriptors allowed by the increased value of
s_groups_count.
Unfortunately, we rather blatently violate this locking protocol
documented in fs/ext4/resize.c. Fortunately, (1) on-line resizes
happen relatively rarely, and (2) it seems rare that the filesystem
code will immediately try to use just-added block group before any
memory ordering issues resolve themselves. So apparently problems
here are relatively hard to hit, since ext3 has been vulnerable to the
same issue for years with no one apparently complaining.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Reduce pressure on the sb_bgl_lock family of locks by using atomic_t's
to track the number of free blocks and inodes in each flex_group.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The static function ext4_group_used_meta_blocks() only has one caller,
who already has access to the block group's group descriptor. So it's
better to have ext4_init_block_bitmap() pass the group descriptor to
ext4_group_used_meta_blocks(), so it doesn't need to call
ext4_group_desc(). Previously this function did not check if
ext4_group_desc() returned NULL due to an error, potentially causing a
kernel OOPS report. This avoids the issue entirely.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Use lowercase names of quota functions instead of old uppercase ones.
Signed-off-by: Jan Kara <jack@suse.cz>
Acked-by: Mingming Cao <cmm@us.ibm.com>
CC: linux-ext4@vger.kernel.org
Running without a journal, I oopsed when I ran out of space,
because we called jbd2_journal_force_commit_nested() from
ext4_should_retry_alloc() without a journal.
This should take care of it, I think.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
When bg_free_blocks_count was renamed to bg_free_blocks_count_lo in
560671a0, its uses under EXT4FS_DEBUG were not changed to the helper
ext4_free_blks_count.
Another commit, 498e5f24, also did not change everything needed under
EXT4FS_DEBUG, thus making it spill some warnings related to printing
format.
This commit fixes both issues and makes ext4 build again when
EXT4FS_DEBUG is enabled.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
For uninit block group, the on-disk bitmap is not initialized. That
implies we cannot depend on the uptodate flag on the bitmap
buffer_head to find bitmap validity. Use a new buffer_head flag which
would be set after we properly initialize the bitmap. This also
prevents (re-)initializing the uninit group bitmap every time we call
ext4_read_block_bitmap().
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Rename some variables. We also unlock locks in the reverse order we
acquired as a part of cleanup.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Rename the lower bits with suffix _lo and add helper
to access the values. Also rename bg_itable_unused_hi
to bg_pad as in e2fsprogs.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The new groups added during resize are flagged as
need_init group. Make sure we properly initialize these
groups. When we have block size < page size and we are adding
new groups the page may still be marked uptodate even though
we haven't initialized the group. While forcing the init
of buddy cache we need to make sure other groups part of the
same page of buddy cache is not using the cache.
group_info->alloc_sem is added to ensure the same.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
cc: stable@kernel.org
With this change new blocks added during resize
are marked as free in the block bitmap and the
group is flagged with EXT4_GROUP_INFO_NEED_INIT_BIT
flag. This makes sure when mballoc tries to allocate
blocks from the new group we would reload the
buddy information using the bitmap present in the disk.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@kernel.org
Convert the unsigned longs that are most responsible for bloating the
stack usage on 64-bit systems.
Nearly all places in the ext3/4 code which uses "unsigned long" is
probably a bug, since on 32-bit systems a ulong a 32-bits, which means
we are wasting stack space on 64-bit systems.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Nearly all places in the ext3/4 code which uses "unsigned long" is
probably a bug, since on 32-bit systems a ulong a 32-bits, which means
we are wasting stack space on 64-bit systems.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This removes annoying blank syslog entries emitted by ext4_error() or
ext4_warning(), since these functions add their own newline.
Signed-off-by: Nick Warne <nick@ukfsn.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
A few weeks ago I posted a patch for discussion that allowed ext4 to run
without a journal. Since that time I've integrated the excellent
comments from Andreas and fixed several serious bugs. We're currently
running with this patch and generating some performance numbers against
both ext2 (with backported reservations code) and ext4 with and without
a journal. It just so happens that running without a journal is
slightly faster for most everything.
We did
iozone -T -t 4 s 2g -r 256k -T -I -i0 -i1 -i2
which creates 4 threads, each of which create and do reads and writes on
a 2G file, with a buffer size of 256K, using O_DIRECT for all file opens
to bypass the page cache. Results:
ext2 ext4, default ext4, no journal
initial writes 13.0 MB/s 15.4 MB/s 15.7 MB/s
rewrites 13.1 MB/s 15.6 MB/s 15.9 MB/s
reads 15.2 MB/s 16.9 MB/s 17.2 MB/s
re-reads 15.3 MB/s 16.9 MB/s 17.2 MB/s
random readers 5.6 MB/s 5.6 MB/s 5.7 MB/s
random writers 5.1 MB/s 5.3 MB/s 5.4 MB/s
So it seems that, so far, this was a useful exercise.
Signed-off-by: Frank Mayhar <fmayhar@google.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
The convenience function do_blk_alloc() is a static function with only
one caller, so fold it into ext4_new_meta_blocks() to simplify the
code and to make it easier to understand.
To save more stack space, if count is a null pointer in
ext4_new_meta_blocks() assume that caller wanted a single block (and
if there is an error, no blocks were allocated).
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There were only two one callers of the function ext4_new_meta_block(),
which just a very simpler wrapper function around
ext4_new_meta_blocks(). Change those two functions to call
ext4_new_meta_blocks() directly, to save code and stack space usage.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
There was only one caller of the compatibility function
ext4_new_blocks(), in balloc.c's ext4_alloc_blocks(). Change it to
call ext4_mb_new_blocks() directly, and remove ext4_new_blocks()
altogether. This cleans up the code, by removing two extra functions
from the call chain, and hopefully saving some stack usage.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
fs/ext4/balloc.c:607: warning: format '%lld' expects type 'long long int', but argument 2 has type 's64'
fs/ext4/inode.c:1822: warning: format '%lld' expects type 'long long int', but argument 2 has type 's64'
fs/ext4/inode.c:1824: warning: format '%lld' expects type 'long long int', but argument 2 has type 's64'
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Revert
commit e8ced39d5e
Author: Mingming Cao <cmm@us.ibm.com>
Date: Fri Jul 11 19:27:31 2008 -0400
percpu_counter: new function percpu_counter_sum_and_set
As described in
revert "percpu counter: clean up percpu_counter_sum_and_set()"
the new percpu_counter_sum_and_set() is racy against updates to the
cpu-local accumulators on other CPUs. Revert that change.
This means that ext4 will be slow again. But correct.
Reported-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mingming Cao <cmm@us.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Cc: <stable@kernel.org> [2.6.27.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert
commit 1f7c14c62c
Author: Mingming Cao <cmm@us.ibm.com>
Date: Thu Oct 9 12:50:59 2008 -0400
percpu counter: clean up percpu_counter_sum_and_set()
Before this patch we had the following:
percpu_counter_sum(): return the percpu_counter's value
percpu_counter_sum_and_set(): return the percpu_counter's value, copying
that value into the central value and zeroing the per-cpu counters before
returning.
After this patch, percpu_counter_sum_and_set() has gone, and
percpu_counter_sum() gets the old percpu_counter_sum_and_set()
functionality.
Problem is, as Eric points out, the old percpu_counter_sum_and_set()
functionality was racy and wrong. It zeroes out counters on "other" cpus,
without holding any locks which will prevent races agaist updates from
those other CPUS.
This patch reverts 1f7c14c62c. This means
that percpu_counter_sum_and_set() still has the race, but
percpu_counter_sum() does not.
Note that this is not a simple revert - ext4 has since started using
percpu_counter_sum() for its dirty_blocks counter as well.
Note that this revert patch changes percpu_counter_sum() semantics.
Before the patch, a call to percpu_counter_sum() will bring the counter's
central counter mostly up-to-date, so a following percpu_counter_read()
will return a close value.
After this patch, a call to percpu_counter_sum() will leave the counter's
central accumulator unaltered, so a subsequent call to
percpu_counter_read() can now return a significantly inaccurate result.
If there is any code in the tree which was introduced after
e8ced39d5e was merged, and which depends
upon the new percpu_counter_sum() semantics, that code will break.
Reported-by: Eric Dumazet <dada1@cosmosbay.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mingming Cao <cmm@us.ibm.com>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wrap access to task credentials so that they can be separated more easily from
the task_struct during the introduction of COW creds.
Change most current->(|e|s|fs)[ug]id to current_(|e|s|fs)[ug]id().
Change some task->e?[ug]id to task_e?[ug]id(). In some places it makes more
sense to use RCU directly rather than a convenient wrapper; these will be
addressed by later patches.
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: James Morris <jmorris@namei.org>
Acked-by: Serge Hallyn <serue@us.ibm.com>
Cc: Stephen Tweedie <sct@redhat.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: adilger@sun.com
Cc: linux-ext4@vger.kernel.org
Signed-off-by: James Morris <jmorris@namei.org>
As reported by Eric Paris, the capable() check in ext4_has_free_blocks()
sometimes causes SELinux denials.
We can rearrange the logic so that we only try to use the root-reserved
blocks when necessary, and even then we can move the capable() test
to last, to avoid the check most of the time.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Mingming pointed out that ext4_claim_free_blocks & ext4_has_free_blocks
are largely cut & pasted; they can be collapsed/merged as follows.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Reviewed-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We need to make sure we don't reuse the data blocks released
during the transaction untill the transaction commits. We force
this mode only for ordered and journalled mode. Writeback mode
already don't provided data consistency.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This fixes a bug which caused on-line resizing of filesystems with a
1k blocksize to fail. The root cause of this bug was the fact that if
an uninitalized bitmap block gets read in by userspace (which
e2fsprogs does try to avoid, but can happen when the blocksize is less
than the pagesize and an adjacent blocks is read into memory)
ext4_read_block_bitmap() was erroneously depending on the buffer
uptodate flag to decide whether it needed to initialize the bitmap
block in memory --- i.e., to set the standard set of blocks in use by
a block group (superblock, bitmaps, inode table, etc.). Essentially,
ext4_read_block_bitmap() assumed it was the only routine that might
try to read a block containing a block bitmap, which is simply not
true.
To fix this, ext4_read_block_bitmap() and ext4_read_inode_bitmap()
must always initialize uninitialized bitmap blocks. Once a block or
inode is allocated out of that bitmap, it will be marked as
initialized in the block group descriptor, so in general this won't
result any extra unnecessary work.
Signed-off-by: Frederic Bohe <frederic.bohe@bull.net>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Make sure we don't add the inode to the journal handle until after the
block allocation, so that a journal commit will not include the inode in
case of block allocation failure.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
We run into ENOSPC error on nonmballoc ext4, even when there is free blocks
on the filesystem.
The patch includes two changes:
a) Set reservation to NULL if we trying to allocate near group_target_block
from the goal group if the free block in the group is less than windows.
This should give us a better chance to allocate near group_target_block.
This also ensures that if we are not allocating near group_target_block
then we don't trun off reservation. This should enable us to allocate
with reservation from other groups that have large free blocks count.
b) we don't need to check the window size if the block reservation is off.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch converts some usage of ext4_fsblk_t to s64. This is needed
so that some of the sign conversion works as expected in if loops.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
This patch adds dirty block accounting using percpu_counters. Delayed
allocation block reservation is now done by updating dirty block
counter. In a later patch we switch to non delalloc mode if the
filesystem free blocks is greater than 150% of total filesystem dirty
blocks
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao<cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
During block reservation if we don't have enough blocks left, retry
block reservation with smaller block counts. This makes sure we try
fallocate and DIO with smaller request size and don't fail early. The
delayed allocation reservation cannot try with smaller block count. So
retry block reservation to handle temporary disk full conditions. Also
print free blocks details if we fail block allocation during writepages.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
With delayed allocation we need to make sure block are reserved before
we attempt to allocate them. Otherwise we get block allocation failure
(ENOSPC) during writepages which cannot be handled. This would mean
silent data loss (We do a printk stating data will be lost). This patch
updates the DIO and fallocate code path to do block reservation before
block allocation. This is needed to make sure parallel DIO and fallocate
request doesn't take block out of delayed reserve space.
When free blocks count go below a threshold we switch to a slow patch
which looks at other CPU's accumulated percpu counter values.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
percpu_counter_sum_and_set() and percpu_counter_sum() is the same except
the former updates the global counter after accounting. Since we are
taking the fbc->lock to calculate the precise value of the counter in
percpu_counter_sum() anyway, it should simply set fbc->count too, as the
percpu_counter_sum_and_set() does.
This patch merges these two interfaces into one.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: <linux-ext4@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Fix ext4_has_free_blocks() to return 0 when we don't have enough space.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
I noticed when filling a 1T filesystem with 4 threads using the
fs_mark benchmark:
fs_mark -d /mnt/test -D 256 -n 100000 -t 4 -s 20480 -F -S 0
that I occasionally got checksum mismatch errors:
EXT4-fs error (device sdb): ext4_init_inode_bitmap: Checksum bad for group 6935
etc. I'd reliably get 4-5 of them during the run.
It appears that the problem is likely a race to init the bg's
when the uninit_bg feature is enabled.
With the patch below, which adds sb_bgl_locking around initialization,
I was able to complete several runs with no errors or warnings.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
ext4_read_block_bitmap and read_inode_bitmap do essentially
the same thing, and yet they are structured quite differently.
I came across this difference while looking at doing bg locking
during bg initialization.
This patch:
* removes unnecessary casts in the error messages
* renames read_inode_bitmap to ext4_read_inode_bitmap
* and more substantially, restructures the inode bitmap
reading function to be more like the block bitmap counterpart.
The change to the inode bitmap reader simplifies the locking
to be applied in the next patch.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
This patch does block reservation for delayed
allocation, to avoid ENOSPC later at page flush time.
Blocks(data and metadata) are reserved at da_write_begin()
time, the freeblocks counter is updated by then, and the number of
reserved blocks is store in per inode counter.
At the writepage time, the unused reserved meta blocks are returned
back. At unlink/truncate time, reserved blocks are properly released.
Updated fix from Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
to fix the oldallocator block reservation accounting with delalloc, added
lock to guard the counters and also fix the reservation for meta blocks.
Signed-off-by: Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: Theodore Ts'o <tytso@mit.edu>
Delayed allocation need to check free blocks at every write time.
percpu_counter_read_positive() is not quit accurate. delayed
allocation need a more accurate accounting, but using
percpu_counter_sum_positive() is frequently is quite expensive.
This patch added a new function to update center counter when sum
per-cpu counter, to increase the accurate rate for next
percpu_counter_read() and require less calling expensive
percpu_counter_sum().
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
mballoc allocation missed check for blocks reserved for root users. Add
ext4_has_free_blocks() check before allocation. Also modified
ext4_has_free_blocks() to support multiple block allocation request.
Signed-off-by: Mingming Cao <cmm@us.ibm.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
