mmc_init_request() depends on card->bouncesz so it must be calculated
before blk_init_allocated_queue() starts allocating requests.
Reported-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Fixes: 304419d8a7 ("mmc: core: Allocate per-request data using the..")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Seraphime Kirkovski <kirkseraph@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Pavel Machek <pavel@ucw.cz>
mmc_start_areq() is an internal mmc core API. Move the declaration
accordingly.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intention for this patch is to help folks debug the failure
like this:
dwmmc_rockchip fe320000.dwmmc: IDMAC supports 32-bit address mode.
dwmmc_rockchip fe320000.dwmmc: Using internal DMA controller.
dwmmc_rockchip fe320000.dwmmc: Version ID is 270a
dwmmc_rockchip fe320000.dwmmc: DW MMC controller at irq 28,32 bit
host data width,256 deep fifo
dwmmc_rockchip fe320000.dwmmc: Got CD GPIO
mmc_host mmc0: Bus speed (slot 0) = 400000Hz (slot req 400000Hz, actual
400000HZ div = 0)
mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 50000000Hz,
actual 50000000HZ div = 0)
mmc0: new high speed SDHC card at address 0007
mmcblk: probe of mmc0:0007 failed with error -28
The reason may be some buggy userspace daemon miss the disk remove
uevent sometimes so it would finally make the SD card not work.
So from the dmesg it only shows a errno of -28 but still don't understand
what happened.
For quick reproduce this, we could set max_devices to 8 and run
for i in $(seq 1 9); do
echo "========================" $i
echo fe320000.dwmmc > /sys/bus/platform/drivers/dwmmc_rockchip/unbind
sleep .5
echo fe320000.dwmmc > /sys/bus/platform/drivers/dwmmc_rockchip/bind
sleep .5
mount -t vfat /dev/mmcblk0 /mnt
sleep .5
done
Another possible reason would be the device has more partitions than
what we support, so that they have to increase their max_devices.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of passing a block device to
mmc_blk_ioctl[_multi]_cmd(), let's pass struct mmc_blk_data()
so we operate ioctl()s on the MMC block device representation
rather than the vanilla block device.
This saves a little duplicated code and makes it possible to
issue ioctl()s not targeted for a specific block device but
rather for a specific partition/area.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Instead of passing a struct mmc_blk_data * to mmc_blk_part_switch()
let's pass the actual partition type we want to switch to. This
is necessary in order not to have a block device with a backing
mmc_blk_data and request queue and all for every hardware partition,
such as RPMB.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_blk_ioctl() calls either mmc_blk_ioctl_cmd() or
mmc_blk_ioctl_multi_cmd() and each of these make the same
check. Factor it into a new helper function, call it on
both branches of the switch() statement and save a chunk
of duplicate code.
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
If we don't have the block layer enabled, we do not present card
status and extcsd in the debugfs.
Debugfs is not ABI, and maintaining files of no relevance for
non-block devices comes at a high maintenance cost if we shall
support it with the block layer compiled out.
The debugfs entries suffer from all the same starvation
issues as the other userspace things, under e.g. a heavy
dd operation.
The expected number of debugfs users utilizing these two
debugfs files is already low as there is an ioctl() to get the
same information using the mmc-tools, and of these few users
the expected number of people using it on SDIO or combo cards
are expected to be zero.
It is therefore logical to move this over to the block layer
when it is enabled, using the new custom requests and issue
it using the block request queue.
On the other hand it moves some debugfs code from debugfs.c
and into block.c.
Tested during heavy dd load by cat:in the status file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This function retrieves the status of the card with the default
number of retries. Since the block layer wants to use this, and
since the block layer is a loadable kernel module, we need to
export this symbol.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have a data pointer for the ioctl() data, but we need to
pass other data along with the DRV_OP:s, so make this a
void * so it can be reused.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The new lockdep annotations for completions cause a warning in the
mmc test module, in a function that now has four 150 byte structures
on the stack:
drivers/mmc/core/mmc_test.c: In function 'mmc_test_nonblock_transfer.constprop':
drivers/mmc/core/mmc_test.c:892:1: error: the frame size of 1360 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
The mmc_test_ongoing_transfer function evidently had a similar problem,
and worked around it by using dynamic allocation.
This generalizes the approach used by mmc_test_ongoing_transfer() and
applies it to mmc_test_nonblock_transfer() as well.
Fixes: cd8084f91c ("locking/lockdep: Apply crossrelease to completions")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
CQE needs to be off for the host controller to accept non-CQ commands. Turn
off the CQE before sending commands, and ensure it is off in any reset or
power management paths, or re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
mmc_return_hold() / mmc_retune_release() are used around a group of
commands to prevent re-tuning between the commands. Re-tuning can still
happen before the first command. In some cases, re-tuning must be
prevented entirely. Add mmc_retune_hold_now() for that purpose. It is
added in preparation for CQE support where it will be used by CQE recovery.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Packed commands support was removed but some bits got left behind. Remove
them.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the SD physical layer simplified specification V4.10,
section 4.6.2, CSD version 1.0 SD card should use taac, nsac
and r2w_factor for calculating the data access time. But the
taac and nsac for SDHC(CSD version 2.0) are always fixed and
the software should use the recommended value for timeout. When
parsing the CSD, we sanely set them to zero for SDHC(CSD version
2.0), all the calculation for timeout_ns and timeout_clk is zero
as well. So what we actually want to limit here is either SDHC
case or unreasonable timeout reported by the cards. In principle
we should at least be able to remove the bogus check for the
mmc_card_blockaddr.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Per the spec of JESD84-B51, section 7.3, replace tacc with taac to
fix the obvious typo.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Jan Glauber <jglauber@cavium.com>
Cc: David Daney <david.daney@cavium.com>
Cc: "Steven J. Hill" <Steven.Hill@cavium.com>
Cc: linux-mmc@vger.kernel.org
Acked-by: David Daney <david.daney@cavium.com>
Tested-by: Steven J. Hill <Steven.Hill@cavium.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are lots of debug message in core.c which use pr_debug
for better dynamic log level control. So it doesn't make sense
for those print to still keep working only under CONFIG_MMC_DEBUG.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
All the check within mmc_mrq_prep seems to be all-or-none
proposition, so it doesn't make sense to only check the
length of sglist only under the CONFIG_MMC_DEBUG context.
I'd prefer to always keep the check there unconditionally.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The intention of this check was to prevent the conflict between
hotplug and removing driver for whatever reason. Currently it
doesn't improve anything and the following rescan process could
still saftly perform the scan flow. So these code seems pointless
now and let's remove them.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was never used and introduced a long standing compile
warning:
drivers/mmc/core/block.c: In function 'power_ro_lock_store':
drivers/mmc/core/block.c:191:19: warning: variable 'card' set but not
used [-Wunused-but-set-variable]
Remove it to fix the warning.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Just a trivial fix for that found by reading the code.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 2a842acab1 ("block: introduce new block status code type") changed
the error type but not in patches merged through the mmc tree, like
commit 0493f6fe5b ("mmc: block: Move boot partition locking into a driver
op"). Fix one error code that is incorrect and also use BLK_STS_OK in
preference to 0.
Fixes: 17ece345a0 ("Merge tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We to some extent should tolerate R1_OUT_OF_RANGE for open-ending
mode as it is expected behaviour and most of the backup partition
tables should be located near some of the last blocks which will
always make open-ending read exceed the capacity of cards.
Fixes: 9820a5b111 ("mmc: core: for data errors, take response of stop cmd into account")
Fixes: a04e6bae9e ("mmc: core: check also R1 response for stop commands")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Change the default err value to -EINVAL, make sure the card only
has type EXT_CSD_CARD_TYPE_HS400_1_8V also do the signal voltage
setting when select hs400es mode.
Fixes: commit 1720d3545b ("mmc: core: switch to 1V8 or 1V2 for hs400es mode")
Cc: <stable@vger.kernel.org>
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The commit 304419d8a7 ("mmc: core: Allocate per-request data using the
block layer core") refactored mechanism of queue handling caused
mmc_init_request() can be called just after mmc_cleanup_queue() caused null
pointer dereference.
Another commit bbdc74dc19 ("mmc: block: Prevent new req entering queue
after its cleanup") tried to fix the problem. However it actually miss one
corner case.
We could still reproduce the issue mentioned with these steps:
(1) insert a SD card and mount it
(2) hotplug it, so it will leave md->usage still be counted
(3) reboot the system which will sync data and umount the card
[Unable to handle kernel NULL pointer dereference at virtual address
00000000
[user pgtable: 4k pages, 48-bit VAs, pgd = ffff80007bab3000
[[0000000000000000] *pgd=000000007a828003, *pud=0000000078dce003,
*pmd=000000007aab6003, *pte=0000000000000000
[Internal error: Oops: 96000007 [#1] PREEMPT SMP
[Modules linked in:
[CPU: 3 PID: 3507 Comm: umount Tainted: G W
4.13.0-rc1-next-20170720-00012-g9d9bf45 #33
[Hardware name: Firefly-RK3399 Board (DT)
[task: ffff80007a1de200 task.stack: ffff80007a01c000
[PC is at mmc_init_request+0x14/0xc4
[LR is at alloc_request_size+0x4c/0x74
[pc : [<ffff0000087d7150>] lr : [<ffff000008378fe0>] pstate: 600001c5
[sp : ffff80007a01f8f0
....
[[<ffff0000087d7150>] mmc_init_request+0x14/0xc4
[[<ffff000008378fe0>] alloc_request_size+0x4c/0x74
[[<ffff00000817ac28>] mempool_create_node+0xb8/0x17c
[[<ffff00000837aadc>] blk_init_rl+0x9c/0x120
[[<ffff000008396580>] blkg_alloc+0x110/0x234
[[<ffff000008396ac8>] blkg_create+0x424/0x468
[[<ffff00000839877c>] blkg_lookup_create+0xd8/0x14c
[[<ffff0000083796bc>] generic_make_request_checks+0x368/0x3b0
[[<ffff00000837b050>] generic_make_request+0x1c/0x240
So mmc_blk_put wouldn't calling blk_cleanup_queue which actually the
QUEUE_FLAG_DYING and QUEUE_FLAG_BYPASS should stay. Block core expect
blk_queue_bypass_{start, end} internally to bypass/drain the queue before
actually dying the queue, so it didn't expose API to set the queue bypass.
I think we should set QUEUE_FLAG_BYPASS whenever queue is removed, although
the md->usage is still counted, as no dispatch queue could be found then.
Fixes: 304419d8a7 ("mmc: core: Allocate per-request data using the block layer core")
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With gcc 4.1.2:
drivers/mmc/core/block.c: In function ‘mmc_blk_ioctl_cmd_issue’:
drivers/mmc/core/block.c:630: warning: ‘ioc_err’ may be used uninitialized in this function
Indeed, if mq_rq->ioc_count is zero, an uninitialized value will be
stored in mq_rq->drv_op_result and passed to blk_end_request_all().
Can mq_rq->ioc_count be zero?
- mmc_blk_ioctl_cmd() sets ioc_count to 1, so this is safe,
- mmc_blk_ioctl_multi_cmd() obtains ioc_count from user space in
response to the MMC_IOC_MULTI_CMD ioctl, and does allow zero.
To avoid returning an uninitialized value, and as it is pointless to do
all this work when the MMC_IOC_MULTI_CMD ioctl is used with zero
entries, check for this early in mmc_blk_ioctl_multi_cmd(), and return
zero, like was returned before.
Fixes: 3ecd8cf23f ("mmc: block: move multi-ioctl() to use block layer")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
With gcc 4.1.2:
drivers/mmc/core/block.c: In function ‘mmc_blk_issue_drv_op’:
drivers/mmc/core/block.c:1178: warning: ‘ret’ may be used uninitialized in this function
Indeed, for MMC_DRV_OP_IOCTL, if mq_rq->ioc_count is zero, an
uninitialized value will be stored in mq_rq->drv_op_result and passed to
blk_end_request_all().
Can mq_rq->ioc_count be zero?
- mmc_blk_ioctl_cmd() sets ioc_count to 1, so this is safe,
- mmc_blk_ioctl_multi_cmd() obtains ioc_count from user space in
response to the MMC_IOC_MULTI_CMD ioctl, and does allow zero.
Initialize ret to zero to fix this for current and future callers.
Fixes: 0493f6fe5b ("mmc: block: Move boot partition locking into a driver op")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
- Add support to enable irq wake for slot gpio
- Remove MMC_CAP2_HC_ERASE_SZ and make it the default behaviour
- Improve R1 response error checks for stop commands
- Cleanup and clarify some MMC specific code
- Keep card runtime resumed while adding SDIO function devices
- Use device_property_read instead of of_property_read in mmc_of_parse()
- Move boot partition locking into a driver op to enable proper I/O scheduling
- Move multi/single-ioctl() to use block layer to enable proper I/O scheduling
- Delete bounce buffer Kconfig option
- Improve the eMMC HW reset support provided via the eMMC pwrseq
- Add host API to manage SDIO IRQs from a workqueue
MMC host:
- dw_mmc: Drop support for multiple slots
- dw_mmc: Use device_property_read instead of of_property_read
- dw_mmc-rockchip: Optional improved tuning to greatly decrease tuning time
- dw_mmc: Prevent rpm suspend for SDIO IRQs instead of always for SDIO cards
- dw_mmc: Convert to use MMC_CAP2_SDIO_IRQ_NOTHREAD for SDIO IRQs
- omap_hsmmc: Convert to mmc regulator APIs to consolidate code
- omap_hsmmc: Deprecate "vmmc_aux" in DT and use "vqmmc" instead
- tmio: make sure SDIO gets reinitialized after resume
- sdhi: add CMD23 support to R-Car Gen2 & Gen3
- tmio: add CMD23 support
- sdhi/tmio: Refactor code and rename files to simplify Kconfig options
- sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
- sdhci-pci: Add support for Intel CNP
- sdhci-esdhc-imx: Remove ENGcm07207 workaround - allow multi block transfers
- sdhci-esdhc-imx: Allow all supported prescaler values
- sdhci-esdhc-imx: Fix DAT line software reset
- sdhci-esdhc: Add SDHCI_QUIRK_32BIT_DMA_ADDR
- atmel-mci: Drop AVR32 support
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=zJi3
-----END PGP SIGNATURE-----
Merge tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Add support to enable irq wake for slot gpio
- Remove MMC_CAP2_HC_ERASE_SZ and make it the default behaviour
- Improve R1 response error checks for stop commands
- Cleanup and clarify some MMC specific code
- Keep card runtime resumed while adding SDIO function devices
- Use device_property_read instead of of_property_read in mmc_of_parse()
- Move boot partition locking into a driver op to enable proper I/O scheduling
- Move multi/single-ioctl() to use block layer to enable proper I/O scheduling
- Delete bounce buffer Kconfig option
- Improve the eMMC HW reset support provided via the eMMC pwrseq
- Add host API to manage SDIO IRQs from a workqueue
MMC host:
- dw_mmc: Drop support for multiple slots
- dw_mmc: Use device_property_read instead of of_property_read
- dw_mmc-rockchip: Optional improved tuning to greatly decrease tuning time
- dw_mmc: Prevent rpm suspend for SDIO IRQs instead of always for SDIO cards
- dw_mmc: Convert to use MMC_CAP2_SDIO_IRQ_NOTHREAD for SDIO IRQs
- omap_hsmmc: Convert to mmc regulator APIs to consolidate code
- omap_hsmmc: Deprecate "vmmc_aux" in DT and use "vqmmc" instead
- tmio: make sure SDIO gets reinitialized after resume
- sdhi: add CMD23 support to R-Car Gen2 & Gen3
- tmio: add CMD23 support
- sdhi/tmio: Refactor code and rename files to simplify Kconfig options
- sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
- sdhci-pci: Add support for Intel CNP
- sdhci-esdhc-imx: Remove ENGcm07207 workaround - allow multi block transfers
- sdhci-esdhc-imx: Allow all supported prescaler values
- sdhci-esdhc-imx: Fix DAT line software reset
- sdhci-esdhc: Add SDHCI_QUIRK_32BIT_DMA_ADDR
- atmel-mci: Drop AVR32 support"
* tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (86 commits)
mmc: dw_mmc: remove the unnecessary slot variable
mmc: dw_mmc: use the 'slot' instead of 'cur_slot'
mmc: dw_mmc: remove the 'id' arguments about functions relevant to slot
mmc: dw_mmc: change the array of slots
mmc: dw_mmc: remove the loop about finding slots
mmc: dw_mmc: deprecated the "num-slots" property
mmc: dw_mmc-rockchip: parse rockchip, desired-num-phases from DT
dt-bindings: rockchip-dw-mshc: add optional rockchip, desired-num-phases
mmc: renesas-sdhi: improve checkpatch cleanness
mmc: tmio: improve checkpatch cleanness
mmc: sdhci-pci: Enable card detect wake for Intel BYT-related SD controllers
mmc: slot-gpio: Add support to enable irq wake on cd_irq
mmc: core: Remove MMC_CAP2_HC_ERASE_SZ
mmc: core: for data errors, take response of stop cmd into account
mmc: core: check also R1 response for stop commands
mmc: core: Clarify code for sending CSD
mmc: core: Drop mmc_all_send_cid() and use mmc_send_cxd_native() instead
mmc: core: Re-factor code for sending CID
mmc: core: Remove redundant code in mmc_send_cid()
mmc: core: Make mmc_can_reset() static
...
BLK_BOUNCE_ANY is the defauly now, so the call is superflous.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add host capability MMC_CAP_CD_WAKE to enable irq wake on the card detect
irq.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The MMC_CAP2_HC_ERASE_SZ is used only by a few mmc host drivers. Its intent
is to enable eMMC's high-capacity erase size, as to improve the behaviour
of the erase operations.
We should strive to avoid software configuration options that aren't
necessary, but instead deploy common behaviours. For these reasons, let's
remove the capability bit for MMC_CAP2_HC_ERASE_SZ and make it the default
behaviour.
Note that this change doesn't affect eMMCs supporting trim/discard, because
these commands operates on sectors and takes precedence over erase
commands.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Some errors are flagged only with the next command after a multiblock
transfer, e.g. ECC error. So, when checking for data transfer errors,
we check the result from the stop command as well.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To detect errors like ECC errors, we must parse the R1 response bits. Introduce
a helper function to also set the error value of a command when R1 error bits
are set. Add ECC error to list of flags checked. Use the new helper for the
stop command to call mmc_blk_recovery when detecting ECC errors which are only
flagged on the next command after multiblock.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
To make the code more consistent and to increase readability, add an
mmc_spi_send_csd() function, which gets called from mmc_send_csd() in case
of SPI mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Instead of having the caller to check for SPI mode, let's leave that to
internals of mmc_send_cid(). In this way the code gets cleaner and it
becomes clear what is specific to SPI and non-SPI mode.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_send_cid() is never called using non SPI mode. Thus, let's remove
the redundant code dealing with this.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_flush_cache() is a eMMC specific function, let's move it to
mmc_ops.c to make that clear.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_interrupt_hpi() is a eMMC specific function, let's move it to
mmc_ops.c to make that clear. The move also enables us to make
mmc_send_hpi_cmd() static, so let's do that change as well.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_start_bkops(), mmc_stop_bkops() and mmc_read_bkops_status()
functions are all specific to eMMCs. To make this clear, let's move them
from from core.c to mmc_ops.c and take the opportunity to make
mmc_read_bkops_status() static.
While moving them, get rid of MMC_BKOPS_MAX_TIMEOUT (4 min) and use the
common default timeout MMC_OPS_TIMEOUT_MS (10 min) instead, as there is no
need to have specific default timeout for bkops.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
The mmc_start|stop_bkops(), mmc_read_bkops_status() and mmc_interrupt_hpi()
functions are all used from within the mmc core module, thus there are no
need to use EXPORT_SYMBOL() for them, so let's remove it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
Drivers core will runtime suspend a device with no driver. That means the
SDIO card will be runtime suspended as soon as it is added. It is then
runtime resumed to add each function. That is entirely pointless, so add
pm runtime get/put to keep the SDIO card runtime resumed until the function
devices have been added.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The error path deletes the device by calling mmc_sdio_remove() which must
be called without the host claimed. Simplify the error path so it does just
that and add a comment about why we don't disable runtime PM.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Using the device_property interfaces allows mmc drivers to work
on platforms which run on either device tree or ACPI.
Signed-off-by: David Woods <dwoods@mellanox.com>
Reviewed-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: stable@vger.linux.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The only reason to why the mmc block device driver needs to implements its
own version of how to get the status of the card, is that it needs to
specify a different amount of retries.
Therefore add a new exported function which allows the caller to specify
the number of retries and convert everybody to use it, as this simplifies
the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
