TX_PWR_CFG_* setting need to consider below cases
-compesate 20M/40M tx power delta for 2.4/5GHZ band
-limit maximum EIRP tx power to power_level of
regulatory requirement
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For RT3070/RT3090/RT3390 with RX antenna diversity support, we must select
default antenna using gpio control way even if we do not turn on
antenna diversity feature.
Seperate the meaning of TX/RX chain and antenna. Some chips use
2x2 TX/RX chain but may have 3 RX antennas or 1x1 TX/RX chain
but may have 2 RX antennas to do antenna diversity.
Signed-off-by: RA-Jay Hung <jay_hung@ralinktech.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The original code has many macros that are no longer needed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Drivers rtlwifi, and rtl8192ce generate a large number of
sparse warnings. This patch fixes most of them.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify Kconfig and Makefile to build rtl8192cu.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add routine rtlwifi/rtl8192cu/trx.c. This routine differs from the rtl8192ce
file of the same name.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add rtlwifi/rtl8192cu/table.c. These tables are different than the ones used
in rtl8192ce.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add rtlwifi/rtl8192cu/rf.c. This routine is distinct from the one in
rtl8192ce with the same name.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the routine rtlwifi/rtl8192cu/phy.c. Most of the code is included from
rtlwifi/rtl8192c/phy_common.c.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the routine rtlwifi/rtl8192cu/hw.c.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the routine rtlwifi/rtl8192cu/hw.c. This one is distinct from the
routine of the same name in rtl8192ce.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add the rtlwifi/rtl8192cu routines for dm.c, fw.c, led.c and sw.c.
Where possible, these routines use the corresponding code in rtl8192ce.
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move common routines from rtlwifi/rtl8192ce/phy.c and .../rtl8192cu/phy.c
into rtlwifi/rtl8192c/phy_common.c.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Further merge of parameters needed for rtl8192cu. In addition,
some changes needed for rtl8192se and rtl8192de are included
and additional Hungarian notation is removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: George <george0505@realtek.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Modify some rtl8192ce routines for merging with rtl8192cu. In addition,
remove some usage of Hungarian notation.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change modifies rtlwifi/rtl8192ce/def.h to handle rtl8192cu. In
addition, a couple of routines needed for both drivers are converted
to be inline.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This change modifies rtlwifi/rtl8192ce/reg.h to support rtl8192cu.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When op_flush() is called with no drop (drop=false), the driver
tries to tx as many frames as possible in about 100ms on every
hw queue. During this time period frames from sw queue are also
scheduled on to respective hw queue.
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The wl12xx sdio_test code uses wl12xx_get_platform_data, which is
only present when WL12*_SDIO is enabled, so make WL12XX_SDIO_TEST
depend on WL12XX_SDIO so that the needed interface will be present.
sdio_test.c:(.devinit.text+0x13178): undefined reference to `wl12xx_get_platform_data'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Luciano Coelho <luciano.coelho@nokia.com>
Cc: Roger Quadros <roger.quadros@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enable recognition of AR2315 chipsets in ath5k driver.
Reported-by: Simon Morgenthaler <s.morgenthaler@students.unibe.ch>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9170USB will be replaced by carl9170 in the foreseeable
future [2.6.40].
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize caldata to avoid compilation warning.
CC [M] drivers/net/wireless/ath/ath9k/htc_drv_main.o
drivers/net/wireless/ath/ath9k/htc_drv_main.c: In function ‘ath9k_htc_config’:
drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: warning: ‘caldata’ may be used uninitialized in this function
drivers/net/wireless/ath/ath9k/htc_drv_main.c:172: note: ‘caldata’ was declared here
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 59eb21a650 "cfg80211: Extend channel to frequency mapping for 802.11j"
changed the definition of the ieee80211_channel_to_frequency; so fix its
usage in brcmfmac.
Signed-off-by: Stanislav Fomichev <kernel@fomichev.me>
Reviewed-by: Henry Ptasinski <henryp@broadcom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If any of the p54-based drivers are built with CONFIG_P54_LEDS not
defined, the following warning is generated:
CC [M] drivers/net/wireless/p54/main.o
drivers/net/wireless/p54/main.c: In function ‘p54_register_common’:
drivers/net/wireless/p54/main.c:614:21: warning: unused variable ‘priv’
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Johannes pointed out the mess of external function prototypes in the
mac80211-ops.c file. Woe to anyone who changes these functions...
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ssb_wait_bit was designed for only one-bit bitmasks.
People start using it for multi-bit bitmasks. Make the "set" case
is safe for this. The "unset" case is already safe.
This does not change behavior of the current code.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Correct channel setting function must be used for AR2317.
When I tested ahb patch on bullet2 all seemed to work fine,
but it couldn't connect another host (using ibss for example).
During an analysis I observed that it's transmitting on another
channel. I looked into madwifi code and understood that
the problem is in channel setting function. So atheros RF2317 not
fully handled in the current ath5k version and must be patched.
Signed-off-by: Nikolay Ledovskikh <nledovskikh@gmail.com>
Acked-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
taken two RT35XX EDIMAX from DPO_RT3562_3592_3062_LinuxSTA_V2.4.1.1_20101217
Signed-off-by: Xose Vazquez Perez <xose.vazquez@gmail.com>
Acked-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Make /sys/class/bluetooth/hciX a symlink to
path under corresponding tty.
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Add the btusb.c blacklist [0489:e02c] for Atheros AR5BBU12 BT
and add to ath3k.c supported this device.
Signed-off-by: Cho, Yu-Chen <acho@novell.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Quirky dongles sometimes do not use the iso interface which
causes a crash with runtime PM
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
Commit: "p54: enhance rssi->dBm database import"
changed the way how the driver deals with the
rssical data. A new data format was necessary
and hence this patch.
NOTE: (for users with a custom eeprom binary)
I spent some time updating p54tools to support
the new format too: => (git available from)
http://git.kernel.org/?p=linux/kernel/git/chr/p54tools.git
It now comes with a simplistic script "n800_rssi2v2.sh"
which can be used to automate the conversion.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes several shortcomings of the
previous implementation. Features of the
rewrite include:
* handles undocumented "0x0000" word at the
start of the frequency table.
(Affected some early? DELL 1450 USB devices
and my Symbol 5GHz miniPCI card.)
* supports more than just one reference point
per band. (Also needed for the Symbol card.)
* ships with default values in case the eeprom
data is damaged, absent or unsupported.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some channel indices of the low 5GHz band clash with
those of the 2.4GHz band. Therefore we should go
with the channel's center frequency.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Case assert is violated should be quite unlikely.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.
Make asynchronous zd_usb_iowrite16v_async available outside zd_usb.c
and use where possible.
This lower CPU usage from ~10% to ~2% on Intel Atom when running
AP-mode with 100 TU beacon interval.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.
This patch makes zd_usb_iowrite16v use asynchronous urb submit within
zd_usb.c. zd_usb_iowrite16v_async_start is used to initiate writing
multiple commands to device using zd_usb_iowrite16v_async. Each URB
is delayed and submitted to device by next zd_usb_iowrite16v_async
call or by call to zd_usb_iowrite16v_async_end. URBs submitted by
zd_usb_iowrite16v_async have URB_NO_INTERRUPT set and last URB
send by zd_usb_iowrite16v_async_end does not. This lower CPU
usage when doing writes that require multiple URBs.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211rw is using usb_bulk_msg() with usb_sndbulkpipe() on interrupt endpoint.
However usb_bulk_msg() internally corrects this and makes interrupt URB.
It's better to change usb_bulk_msgs in zd1211rw to usb_interrupt_msg for less
confusion.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
