This patch adds the LINK_SPEED mode to the list of CPMU modes that can
cause the loopback tests to fail. These bugs are planned to be fixed in
future revisions of the chip, so the patch qualifies the fixes as such.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer devices contain bootcode in the chip's private ROM area. This
bootcode is called selfboot. Selfboot can be patched in the device's
NVRAM and the patches can have several formats. In one particular
format, the checksum calculation needs to be slightly modified. This
patch adjusts the NVRAM test code for that case, and add support for the
missing formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5784 and 5764 devices lock up when the link speed is 10Mbps, the CPMU
link speed mode is enabled, and the MAC clock is running at 1.5Mhz. The
fix is to run the MAC clock at faster speeds.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a bug where the ENABLE_APE flag was tested against
the wrong flag variable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5784 and 5764 devices fail to link / pass traffic after one load /
unload cycle. This happens because of a hardware bug in the new CPMU.
During normal operation, the MAC depends on the PHY clock being
available. When the PHY is powered down, the clock the MAC depends on
is disabled. The fix is to switch the MAC clock to an alternate source
before powering down the PHY, and to restore the MAC clock to the PHY
source upon device resume.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 5761 devices boot the machine using PXEboot, PXE leaves the device
active when it terminates. The tg3 driver has code to detect this
condition and resets the device during initialization. On 5761 devices,
device resets involve sending a driver state update message to the APE
on the 5761. However, during this initialization stage, communications
to the APE registers have not yet been set up. The driver then
dereferences a NULL pointer and crashes the machine. The fix is to move
the APE register access setup earlier in the initialization code to
cover this condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I removed net-modules.txt because it only contained ancient
information I missed that many Kconfig entries pointed to this ancient
information.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
...and fix a couple of bugs in the NBD, CIFS and OCFS2 socket handlers.
Looking at the sock->op->shutdown() handlers, it looks as if all of them
take a SHUT_RD/SHUT_WR/SHUT_RDWR argument instead of the
RCV_SHUTDOWN/SEND_SHUTDOWN arguments.
Add a helper, and then define the SHUT_* enum to ensure that kernel users
of shutdown() don't get confused.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Acked-by: Mark Fasheh <mark.fasheh@oracle.com>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bea3348e (the NAPI changes) made sungem unconditionally enable
NAPI when resuming and unconditionally disable when suspending, this,
however, makes napi_disable() hang when suspending when the interface
was taken down before suspend because taking the interface down also
disables NAPI. This patch makes touching the napi struct in
suspend/resume code paths depend on having the interface up, thereby
fixing the hang on suspend.
The patch also moves the napi_disable() in gem_close() under the lock so
that the NAPI state is always modified atomically together with the
"opened" variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix sparse warnings "Using plain integer as NULL pointer"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
KVM: SVM: Intercept the 'invd' and 'wbinvd' instructions
KVM: x86 emulator: invd instruction
KVM: SVM: Defer nmi processing until switch to host state is complete
KVM: SVM: Fix SMP with kernel apic
KVM: x86 emulator: fix 'push imm8' emulation
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-virtio:
virtio: Force use of power-of-two for descriptor ring sizes
lguest: Fix lguest virtio-blk backend size computation
virtio: Fix used_idx wrap-around
virtio: more fallout from scatterlist changes.
virtio: fix vring_init for 64 bits
The virtio descriptor rings of size N-1 were nicely set up to be
aligned to an N-byte boundary. But as Anthony Liguori points out, the
free-running indices used by virtio require that the sizes be a power
of 2, otherwise we get problems on wrap (demonstrated with lguest).
So we replace the clever "2^n-1" scheme with a simple "align to page
boundary" scheme: this means that all virtio rings take at least two
pages, but it's safer than guessing cache alignment.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The more_used() function compares the vq->vring.used->idx with last_used_idx.
Since vq->vring.used->idx is a 16-bit integer, and last_used_idx is an
unsigned int, this results in unpredictable behavior when vq->vring.used->idx
wraps around.
This patch corrects this by changing last_used_idx to the correct type.
Signed-off-by: Anthony Liguori <aliguori@us.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This fixes the lowlevel bus access routines for
PCMCIA based devices.
There are still a few issues with register access sideeffects after
this patch. This will be addressed in a later patch.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Prior to this patch, iwlwifi would always use the first
registered rate control algorithm which, depending on system
setup, could be anything. After the mac80211 patch to make
the simple algorithm built-in, it would always be simple.
This has always been a bug in iwlwifi.
This fixes it by requesting that mac80211 selects the right
rate control algorithm.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ssb must init after PCI but before the ssb drivers.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Christian Casteyde <casteyde.christian@free.fr>
Fixes-bug: #9219
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add documentation in Kconfig help about the move of /proc/acpi/battery
to /sys/class/power_supply when selecting ACPI_PROCFS. This will impact
a lot of users and should be documented.
Signed-off-by: Jerome Pinot <ngc891@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
libata: Don't fail device revalidation for bad _GTF methods
libata: port and host should be stopped before hardware resources are released
libata: skip 0xff polling for PATA controllers
libata: pata_platform: Support polling-mode configuration.
libata: Support PIO polling-only hosts.
libata sata_qstor conversion to new error handling (EH).
libata sata_qstor workaround for spurious interrupts
libata sata_qstor nuke idle state
nv_hardreset: update dangling reference to bugzilla entry
ata_piix: add SATELLITE PRO U200 to broken suspend list
Oops.
The current code does not like being given an u16 with the highest
bit set as an argument to mdio_write. Let's enforce a correct range of
values for both the register address and value (resp. 5 and 16 bits).
The callers are currently left as-is.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
RTL_GIGA_MAC_VER_17 breaks as well.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Found a couple of more chips in the latest version of the vendor driver.
They are minor variations on existing chips.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ax88796: add superh to kconfig dependencies
This patch adds sh architecture support to the ax88796 kconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Luckily, this wasn't reported or reproduced. The logical operation for
setting duplex had wrong grouping.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The link state machine requires access to some resources that
are shared with the iSCSI function on the chip. (See iSCSI
driver at drivers/scsi/qla4xxx) If the interface is being
up/downed at a rapid pace this driver may need to sleep
waiting to get access to the common resources. For this we
are moving the state machine to run as a work thread.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure we don't feed packets with bad CRC up the network stack,
and discount the packet length as reported from the MAC for the CRC
field.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't use the "replace source address with local MAC address" bits, since
it causes problems on some variations of the hardware due to an erratum.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The standard validate_addr handler refuses to accept the all zeroes address
as valid. However, it's common historical practice for the bonding
master to be configured up prior to having any slaves, at which time the
master will have a MAC address of all zeroes.
Resolved by setting the dev->validate_addr to NULL. The master still can't
end up with an invalid address, as the set_mac_address function tests
for validity.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Looks like I incorrectly merged one of the rtnl lock changes,
so that one function, bonding_show_active_slave, held rtnl but didn't
release it, and another, bonding_store_active_slave, never held rtnl but
did release it.
Fixed so the first function doesn't mess with rtnl, and the
second correctly acquires and releases rtnl.
Bug reported by Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Netpoll will only work on port 0 because of the restrictive
relationship between NAPI and netpoll.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
PCMCIA needs an additional step to request the IRQ.
No need to add code to release the IRQ here, as that's done
automatically in pcmcia_disable_device().
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an IRQ race condition in b43legacy. If we call
b43legacy_wireless_core_stop(), it will set the status of the device to
INITIALIZED and the IRQ handler won't care any longer about IRQs, thus the
kernel will disable the IRQ if it's shared (unless we boot it with the
'irqpoll' option). So we must disable IRQs before changing the device
status.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an IRQ race condition in b43. If we call b43_stop_wireless_core(), it
will set the status of the device to INITIALIZED and the IRQ handler won't
care any longer about IRQs, thus the kernel will disable the IRQ if it's
shared (unless we boot it with the 'irqpoll' option). So we must disable
IRQs before changing the device status.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix possible buffer overrun.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rfkill subsystem doesn't like code like that
rfkill_allocate();
rfkill_register();
rfkill_unregister();
rfkill_register(); /* <- This will crash */
This sequence happens with
modprobe b43
ifconfig wlanX up
ifconfig wlanX down
ifconfig wlanX up
Fix this by always re-allocating the rfkill stuff before register.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl->mutex might already be locked on initialization.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If i reaches zero, the loop ends, but the postfix decrement subtracts it to -1.
Testing for 'i == 0', later in the function, will not fulfill its purpose.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix section mismatch warning:
WARNING: vmlinux.o(.data+0x36fcc): Section mismatch: reference to .init.data:prism2_pci_id_table (between 'prism2_pci_drv_id' and 'prism2_pci_funcs')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00 is broken when it comes down to adhoc and master mode.
The main problem is the beaconing, which is completely failing.
Untill a solution has been found, both beacon requiring modes
must be disabled to prevent numerous bug reports.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Properly account for queue commands, this fixes a problem reported
by Holger Schurig when using the debugfs interface.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incoming packets have to be aligned or the IP stack becomes upset.
Make sure to shift them two bytes to achieve this.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes for slow hardware.
Signed-off-by: Vitaly V. Bursov <vitalyvb@ukr.net>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Intel device supported by the hermes driver core is the IPW2011. The
"Intel PRO/Wireless" wording suggests the later Centrino devices and may
be confusing to some users.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various symptoms depending on the .config options:
- the card stops working after some (short) time
- the card does not work at all
- the card disappears (nothing in lspci/dmesg)
A real power-off is needed to recover the card.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The 8168c and the 8100e choke on it. I have not seen an indication
nor received a report that the TBI is being actively used on the
remaining 8168b and 8110. Let's disable it for now until someone
complains.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Matthias Winkler <m.winkler@unicon-ka.de>
Cc: Maarten Vanraes <maarten.vanraes@gmail.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
This patch adds LAN91C111 ethernet interface support for zylonite
(a.k.a Marvell's PXA3xx Development Platform) with smc91x driver.
It would be better if a patch would support zylonite along with all
other PXA boards with a single binary of smc91x driver, but it looks
quite difficult for the moment, so ugly #ifdef is still used here.
Signed-off-by: Aleksey Makarov <amakarov@ru.mvista.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PCI AER support may not work for a couple of reasons.
It may not be configured into the kernel or there may be a BIOS
bug that prevents MMCONFIG from working. If MMCONFIG doesn't work
then the PCI registers that control AER will not be accessible via
pci_read_config functions; luckly there is another window to access
PCI space in the device, so use that.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The IRQ's is already masked on shutdown, and on startup avoid
touching PHY until after phy_init().
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't need to change LED's after auto negotiation, the chip
sets them correctly.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Increse phy delay and handle I/O errors.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The D-Link PCI-X board (and maybe others) can lie about status
ring entries. It seems it will update the register for last status
index before completing the DMA for the ring entry. To avoid reading
stale data, zap the old entry and check.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some boards, PCI configuration space access is turned off by default.
The 2.6.24 driver doesn't turn it on, and should have.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Experience suggests that the _GTF method may be bad. We currently fail
device revalidation in that case, which seems excessive.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: remove dead config symbols from SH code
sh: Kill off broken snapgear ds1302 code.
sh: Add a dummy vga.h.
rtc: rtc-sh: Zero out tm value for invalid rtc states.
rtc: sh-rtc: Handle rtc_device_register() failure properly.
sh: Fix heartbeart on Solution Engine series
sh: Remove SCI_NPORTS from sh-sci.h
sh: Fix up PAGE_KERNEL_PCC() for nommu.
sh: hs7751rvoip: Kill off dead IPR IRQ mappings.
sh: hs7751rvoip: irq.c needs linux/interrupt.h.
sh: Kill off __{copy,clear}_user_page().
sh: Optimized copy_{to,from}_user_page() for SH-4.
sh: Wire up clear_user_highpage().
sh: Kill off the remaining ST40 cruft.
superhyway: Handle device_register() retval properly.
sh: kgdb sysrq depends on magic sysrq.
sh: Add -Werror for clean directories.
sh: Fix up kgdb build with modular sh-sci.
sh: Export __{s,u}divsi3_i4i on all CPUs.
sh: Fix up kgdb-on-NMI branch target.
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (37 commits)
[POWERPC] EEH: Make sure warning message is printed
[POWERPC] Make altivec code in swsusp_32.S depend on CONFIG_ALTIVEC
[POWERPC] windfarm: Fix windfarm thread freezer interaction
[POWERPC] Fix si_addr value on low level hash failures
[POWERPC] Refresh ppc64_defconfig and enable pasemi-related options
[POWERPC] pasemi: Update defconfig
[POWERPC] iSeries: Fix ref counting in vio setup
[POWERPC] ] Fix memset size error
[POWERPC] Fix link errors for allyesconfig
[POWERPC] iSeries_init_IRQ non-PCI tidy
[POWERPC] Change fallocate to match unistd.h on powerpc
[POWERPC] EEH: Avoid crash on null device
[POWERPC] EEH: Drivers that need reset trump others
[POWERPC] EEH: Clean up comments
[POWERPC] Fix off-by-one error in setting decrementer on Book E/4xx (v2)
[POWERPC] Fix switch_slb handling of 1T ESID values
[POWERPC] Fix build failure when CONFIG_VIRT_CPU_ACCOUNTING is not defined
[POWERPC] Include udbg.h when using udbg_printf
[POWERPC] Fix cache line vs. block size confusion
[POWERPC] Fix sysctl table check failure on PowerMac
...
Added blk_unplug interface, allowing all invocations of unplugs to result
in a generated blktrace UNPLUG.
Signed-off-by: Alan D. Brunelle <Alan.Brunelle@hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Cyberpro: when user requests 16bpp, use it and not 24bpp.
There was a missing break causing requests for 16bpp mode
to end up in 24bpp mode.
Signed-off-by: Jan Rinze Peterzon <janrinze@home.nl>
Acked-by: Ralph Siemsen <ralphs@netwinder.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Port / host stop calls used to be made from ata_host_release() which
is called after all hardware resources acquired after host allocation
are released. This is wrong as port and host stop routines often
access the hardware.
Add separate devres for port / host stop which is invoked right after
IRQ is released but with all other hardware resources intact. The
devres is added iff ->host_stop and/or ->port_stop exist.
This problem has been spotted by Mark Lord.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In a presentation of true workmanship, pata_ali asserts IRQ
permanantly if the TF status register is read more than once when
there's no device attached to the port.
Avoid waiting polling for !0xff if it's PATA. It's needed only for
some rare SATA devices anyway.
This problem is reported by Luca Tettamanti in bugzilla bug 9298.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Tested-By: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some SH boards (old R2D-1 boards) have generally not had working CF
under libata, due to both buswidth issues (handled by Aoi Shinkai
in 43f4b8c757), and buggy interrupt
controllers. For these sorts of boards simply disabling the IRQ and
polling ends up working fine.
This conditionalizes the IRQ resource for pata_platform and lets
platforms that want to use polling mode simply omit the resource
entirely.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
By default ata_host_activate() expects a valid IRQ in order to
successfully register the host. This patch enables a special case
for registering polling-only hosts that either don't have IRQs
or have buggy IRQ generation (either in terms of handling or
sensing), which otherwise work fine.
Hosts that want to use polling mode can simply set ATA_FLAG_PIO_POLLING
and pass in an invalid IRQ.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_qstor conversion to new error handling (EH).
Convert sata_qstor to use the newer libata EH mechanisms.
Based on earlier work by Jeff Garzik.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_qstor workaround for spurious interrupts.
The qstor hardware generates spurious interrupts from time to time when
switching in and out of packet mode. These eventually result in the
IRQ being disabled, which kills other devices sharing this IRQ with us.
This workaround isn't perfect, but it's about the best we can do for
this hardware. Spurious interrupts will still happen, but won't be
logged as such, and therefore won't cause the IRQ to be inadvertently
disabled.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_qstor nuke idle state.
We're really only ever in one of two hardware states: packet, or mmio.
Get rid of unnecessary "qs_state_idle" state.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Please warmly welcome the PRO variant of Satellite U200 to the broken
suspend list.
Original patch is from Yann Chachkoff. Patch reformatted and
forwarded by Tejun Heo.
Signed-off-by: Yann Chachkoff <yann.chachkoff@myrealbox.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
akpm objected to some of the macros, so convert them into functions.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Missing curly braces cause an if statement to be evaluated when it
shouldn't. It happens to be harmless, but that's still worth fixing.
Thanks to Riku Voipio for reporting.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-By: Riku Voipio <riku.voipio@movial.fi>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This patch changes the identification string for motherboards with an id of
0x001A from unknown to "Abit IP35 Pro". Thanks to James Scott who has an Abit
IP35 Pro.
Signed-off-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix value check in set_pwm_mode(). Instead of checking for chip variant there,
make pwmX_mode sysfs nodes only writable on f75375 variant.
Signed-off-by: Riku Voipio <riku.voipio@movial.fi>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Allow initializing fans on systems where BIOS does not do that by
default.
- define f75375s_platform_data in new file f75375s.h
- if platform_data was provided, set fans accordingly in f75375_init()
- split set_pwm_enable() to a sysfs callback and directly usable
set_pwm_enable_direct()
Signed-off-by: Riku Voipio <riku.voipio@movial.fi>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Following the example of David Brownell's work on lm75:
- Create a second driver struct, using new-style driver binding methods.
- Rename the old driver struct as f75375_legacy_driver.
- Make the legacy bind/unbind logic delegate all its work.
Signed-off-by: Riku Voipio <riku.voipio@movial.fi>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
At least the 2x Quad-Core Apple Mac Pro appears to have some over-heat
protection which suddenly powers off the whole box under load. This adds
support for the fans and temerature sensors in the Mac Pro - later some
"windwarm" a-like code should probably monitor the values. For now
manually tweaking the fans prevents the sudden shutdown for me.
cd /sys/devices/platform/applesmc.768
for x in fan{1,2,3,4}; do
echo 1 > ${x}_manual
echo 1285 > ${x}_output
done
Two sensors are 0, while four are 129 °C, those might be removed again,
later.
Signed-off-by: René Rebe <rene@exactcode.de>
Cc: Nicolas Boichat <nicolas@boichat.ch>
Cc: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Clean up printk use in ibmpex.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
New driver to read FB-DIMM temperature sensors on systems with the
Intel 5000 series chipsets.
Signed-off-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Spotted by the Coverity checker. (Thanks Adrian Bunk)
Signed-off-by: Riku Voipio <riku.voipio@iki.fi>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Don't dereference "data" when we know for sure it's NULL.
Spotted by the Coverity checker.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Use sysfs_create_group instead of individual calls to device_create_file by
splitting sis5595_attributes_opt into sis5595_attributes_in4 and
sis5595_attributes_temp1.
Signed-off-by: Ivo Manca <pinkel@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add individual alarm files needed by the new libsensors.
Signed-off-by: Ivo Manca <pinkel@gmail.com>
Acked-by: Jean Delvare <khali@linux.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
patch changes 2 macros to incorporate the +1, and drops the +1 from all the
callers. This also allows a 'reroll' of an expanded loop, and adjusting
indexes and loop limits on another.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This hoists nr-1 offset out of (show|store)_temp_*(.*) callbacks, and into
SENSOR_DEVICE_ATTRs for sysfs tempN_X files. It also combines
temp[1] and temp_add[2] (array) fields in w83627hf_data into 3 elem arrays,
which simplifies special-case handling of nr, allowing simplification
of callback bodies and rerolling a flattened loop in
w83627hf_update_device(struct device *dev).
The array conversion changes temp[1] from u8 to u16, but this was
happening implicitly via the helper functions anyway.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Commit 45711f1a ("[SG] Update drivers to use sg helpers") had the
following bogus change in drivers/mmc/card/queue.c:
> - src_buf = page_address(src->page) + src->offset;
> + src_buf = sg_virt(dst);
(Notice that "src" is converted to "dst"). Turn this "dst" back into
the intended "src".
Signed-off-by: Roland Dreier <roland@digitalvampire.org>
Tested-by: Romano Giannetti <romano.giannetti@gmail.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
'invd' can destroy host data, and 'wbinvd' allows the guest to induce
long (milliseconds) latencies.
Noted by Ben Serebrin.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If we stgi() too soon, nmis can reach the processor even though interrupts
are disabled, catching it in a half-switched state. Delay the stgi() until
we're done switching.
Signed-off-by: Avi Kivity <avi@qumranet.com>
