This patch allows to use the whole 64-bit timestamps received from the
CAN-FD device (expressed in µs) rather than only its low part, in the
hwtstamp structure of the skb transferred to the network layer, when a
CAN/CANFD frame has been received.
Link: https://lore.kernel.org/all/20210930094603.23134-1-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
ISO 11898-1 specifies in section 11.3.3 "Transmitter delay
compensation" that "the configuration range for [the] SSP position
shall be at least 0 to 63 minimum time quanta."
Because SSP = TDCV + TDCO, it means that we should allow both TDCV and
TDCO to hold zero value in order to honor SSP's minimum possible
value.
However, current implementation assigned special meaning to TDCV and
TDCO's zero values:
* TDCV = 0 -> TDCV is automatically measured by the transceiver.
* TDCO = 0 -> TDC is off.
In order to allow for those values to really be zero and to maintain
current features, we introduce two new flags:
* CAN_CTRLMODE_TDC_AUTO indicates that the controller support
automatic measurement of TDCV.
* CAN_CTRLMODE_TDC_MANUAL indicates that the controller support
manual configuration of TDCV. N.B.: current implementation failed
to provide an option for the driver to indicate that only manual
mode was supported.
TDC is disabled if both CAN_CTRLMODE_TDC_AUTO and
CAN_CTRLMODE_TDC_MANUAL flags are off, c.f. the helper function
can_tdc_is_enabled() which is also introduced in this patch.
Also, this patch adds three fields: tdcv_min, tdco_min and tdcf_min to
struct can_tdc_const. While we are not convinced that those three
fields could be anything else than zero, we can imagine that some
controllers might specify a lower bound on these. Thus, those minimums
are really added "just in case".
Comments of struct can_tdc and can_tdc_const are updated accordingly.
Finally, the changes are applied to the etas_es58x driver.
Link: https://lore.kernel.org/all/20210918095637.20108-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Since alloc_can_err_skb() puts NULL in cf in the case when skb cannot
be allocated and can_change_state() handles the case when cf is NULL,
the test on the nullity of skb is now unnecessary.
Link: https://lore.kernel.org/all/20210929142111.55757-2-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes the interchanged fetch of the CAN RX and TX error
counters from the ESD_EV_CAN_ERROR_EXT message. The RX error counter
is really in struct rx_msg::data[2] and the TX error counter is in
struct rx_msg::data[3].
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Link: https://lore.kernel.org/r/20210825215227.4947-2-stefan.maetje@esd.eu
Cc: stable@vger.kernel.org
Signed-off-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The documentation of struct es58x_fd_tx_conf_msg explains in details
the different TDC parameters. However, those description are redundant
with the documentation of struct can_tdc.
Remove most of the description.
Also, fixes a typo in the reference to the datasheet (E701 -> E70).
Link: https://lore.kernel.org/r/20210815033248.98111-8-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In esd_usb2_setup_rx_urbs() MAX_RX_URBS coherent buffers are allocated
and there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see esd_usb2_setup_rx_urbs) and this flag cannot be used
with coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 96d8e90382 ("can: Add driver for esd CAN-USB/2 device")
Link: https://lore.kernel.org/r/b31b096926dcb35998ad0271aac4b51770ca7cc8.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In ems_usb_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see ems_usb_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 702171adee ("ems_usb: Added support for EMS CPC-USB/ARM7 CAN/USB interface")
Link: https://lore.kernel.org/r/59aa9fbc9a8cbf9af2bbd2f61a659c480b415800.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In usb_8dev_start() MAX_RX_URBS coherent buffers are allocated and
there is nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see usb_8dev_start) and this flag cannot be used with
coherent buffers.
So, all allocated buffers should be freed with usb_free_coherent()
explicitly.
Side note: This code looks like a copy-paste of other can drivers. The
same patch was applied to mcba_usb driver and it works nice with real
hardware. There is no change in functionality, only clean-up code for
coherent buffers.
Fixes: 0024d8ad16 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Link: https://lore.kernel.org/r/d39b458cd425a1cf7f512f340224e6e9563b07bd.1627404470.git.paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Yasushi reported, that his Microchip CAN Analyzer stopped working
since commit 91c0255717 ("can: mcba_usb: fix memory leak in
mcba_usb"). The problem was in missing urb->transfer_dma
initialization.
In my previous patch to this driver I refactored mcba_usb_start() code
to avoid leaking usb coherent buffers. To archive it, I passed local
stack variable to usb_alloc_coherent() and then saved it to private
array to correctly free all coherent buffers on ->close() call. But I
forgot to initialize urb->transfer_dma with variable passed to
usb_alloc_coherent().
All of this was causing device to not work, since dma addr 0 is not
valid and following log can be found on bug report page, which points
exactly to problem described above.
| DMAR: [DMA Write] Request device [00:14.0] PASID ffffffff fault addr 0 [fault reason 05] PTE Write access is not set
Fixes: 91c0255717 ("can: mcba_usb: fix memory leak in mcba_usb")
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=990850
Link: https://lore.kernel.org/r/20210725103630.23864-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Yasushi SHOJI <yasushi.shoji@gmail.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
[mkl: fixed typos in commit message - thanks Yasushi SHOJI]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The es581_tx_can_msg() does below cast:
| tx_can_msg = (struct es581_4_tx_can_msg *)
| &es581_4_urb_cmd->bulk_tx_can_msg.tx_can_msg_buf[msg_len - 1];
The -1 offset is to skip the first member of struct
es581_4_tx_can_msg. However, es581_4_urb_cmd already has a raw_msg
field which can be used instead without the use of an offset
calculation.
The function es58x_fd_tx_can_msg() is also modified to mirror
es581_tx_can_msg().
Link: https://lore.kernel.org/r/20210628155420.1176217-7-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace two constant values by a call to sizeof{,_field} on the
relevant field to make the logic easier to understand.
Link: https://lore.kernel.org/r/20210628155420.1176217-6-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Both es58x_probe() and es58x_disconnect() use a similar code snippet
to release the netdev resources. Factorize it in an helper function
named es58x_free_netdevs().
Link: https://lore.kernel.org/r/20210628155420.1176217-5-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace kzalloc() with devm_kzalloc(). By doing this, we do not need
to care anymore about having to call kfree(). This result in a
simpler and more easy to read code.
Link: https://lore.kernel.org/r/20210628155420.1176217-4-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Make es58x_init_es58x_dev return a pointer to the allocated structure
instead of returning an integer. Errors are handled through the helper
function ERR_PTR and IS_ERR.
This slightly simplifies the code.
Link: https://lore.kernel.org/r/20210628155420.1176217-3-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Change the author name from "lastname firstname" to "firstname
lastname".
Fix a typo in a variable name in the documentation of struct
es58x_parameters::fifo_mask.
Fix a typo in the title of the datasheet (E701 -> E70) and re-indent
the comments.
Link: https://lore.kernel.org/r/20210628155420.1176217-2-mailhol.vincent@wanadoo.fr
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch updates old code by using the can_change_state() function
published since by the socket-can module.
In particular, this new code better manages the change of bus state by
also using the value of the error counters that the driver now
systematically asks for when initializing the channel.
Link: https://lore.kernel.org/r/20210715142842.35793-1-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The CAN - USB PCAN-USB interface is able to generate one-shot frames
as well as loopback frames that it transmits starting from version 4.1
of its firmware.
This patch adds support for the one-shot and loopback functionality to
the driver, that can be activated if the embedded firmware allows it.
If the driver detects that the PCAN-USB device runs an old firmware
(< 4.1) it prints a message suggesting to contact
<support@peak-system.com> for a possible firmware update.
Link: https://lore.kernel.org/r/20210625130931.27438-3-s.grosjean@peak-system.com
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Use DEVICE_ATTR_RO() helper macro instead of plain DEVICE_ATTR(), which
makes the code a bit shorter and easier to read.
Link: https://lore.kernel.org/r/20210603110902.11930-1-thunder.leizhen@huawei.com
Signed-off-by: Zhen Lei <thunder.leizhen@huawei.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch fixes an incorrect way of reading error counters in messages
received for this purpose from the PCAN-USB interface. These messages
inform about the increase or decrease of the error counters, whose values
are placed in bytes 1 and 2 of the message data (not 0 and 1).
Fixes: ea8b33bde7 ("can: pcan_usb: add support of rxerr/txerr counters")
Link: https://lore.kernel.org/r/20210625130931.27438-4-s.grosjean@peak-system.com
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.
In mcba_usb_start() 20 coherent buffers are allocated and there is
nothing, that frees them:
1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see mcba_usb_start) and this flag cannot be used with
coherent buffers.
Fail log:
| [ 1354.053291][ T8413] mcba_usb 1-1:0.0 can0: device disconnected
| [ 1367.059384][ T8420] kmemleak: 20 new suspected memory leaks (see /sys/kernel/debug/kmem)
So, all allocated buffers should be freed with usb_free_coherent()
explicitly
NOTE:
The same pattern for allocating and freeing coherent buffers
is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c
Fixes: 51f3baad7d ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Rename define USB_HYBRID_{,PRO_}CANLIN_PRODUCT_ID to
USB_HYBRID_{,PRO_}2CANLIN_PRODUCT_ID, to reflect the channel count.
Link: https://lore.kernel.org/r/20210429093730.499263-1-extja@kvaser.com
Signed-off-by: Jimmy Assarsson <extja@kvaser.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There is an assignment to *netdev that is that can potentially be null
but the null check is checking netdev and not *netdev as intended. Fix
this by adding in the missing * operator.
Fixes: 8537257874 ("can: etas_es58x: add core support for ETAS ES58X CAN USB interfaces")
Link: https://lore.kernel.org/r/20210415084723.1807935-1-colin.king@canonical.com
Addresses-Coverity: ("Dereference before null check")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
During the handling of CAN bus errors, a CAN error SKB is allocated
using alloc_can_err_skb(). Even if the allocation of the SKB fails,
the function continues in order to do the stats handling.
All access to the can_frame pointer (cf) should be guarded by an if
statement:
if (cf)
However, the increment of the rx_bytes stats:
netdev->stats.rx_bytes += cf->can_dlc;
dereferences the cf pointer and was not guarded by an if condition
leading to a NULL pointer dereference if the can_err_skb() function
failed.
Replacing the cf->can_dlc by the macro CAN_ERR_DLC (which is the
length of any CAN error frames) solves this NULL pointer dereference.
Fixes: 8537257874 ("can: etas_es58x: add core support for ETAS ES58X CAN USB interfaces")
Link: https://lore.kernel.org/r/20210413114242.2760-1-mailhol.vincent@wanadoo.fr
Reported-by: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces the open coded endianness conversion of unaligned
data by the appropriate get/put_unaligned_leXX() variants.
Link: https://lore.kernel.org/r/20210406111622.1874957-11-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The function serial_number is only called from one location with a
valid serial_number pointer. Remove not needed NULL pointer check.
Link: https://lore.kernel.org/r/20210406111622.1874957-10-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The caller of pcan_usb_get_serial() already prints an error message,
so remove this one and return immediately.
Link: https://lore.kernel.org/r/20210406111622.1874957-8-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The callback struct peak_usb_adapter::dev_get_device_id, which is
implemented by the functions pcan_usb_{,pro}_get_device_id() is only
ever called with a valid device_id pointer.
This patch removes the unneeded check if the device_id pointer is
valid.
Link: https://lore.kernel.org/r/20210406111622.1874957-7-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
There's no need to iterate over all supported adapters to find the
struct peak_usb_adapter that describes the currently probed devices's
capabilities. The driver core gives us the information for free, if we
assign it to the struct usb_device_id::driver_info.
This patch assigns the usb_device_id::driver_info and converts
peak_usb_probe() to make use of it. This reduces the driver size by
100 bytes on ARCH=arm.
| add/remove: 0/1 grow/shrink: 0/1 up/down: 0/-124 (-124)
| Function old new delta
| peak_usb_adapters_list 24 - -24
| peak_usb_probe 236 136 -100
| Total: Before=25263, After=25139, chg -0.49%
Link: https://lore.kernel.org/r/20210406111622.1874957-6-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The variable struct peak_usb_adapter::ts_period is only ever written
to. This patch removes it from the driver.
Link: https://lore.kernel.org/r/20210406111622.1874957-5-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch removes the unused variables struct
peak_usb_device::echo_skb and struct peak_usb_device::bus_load from
the driver.
Link: https://lore.kernel.org/r/20210406111622.1874957-4-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch replaces the double space indention after the u8 with a
single space in pcan_usb_pro.h.
Link: https://lore.kernel.org/r/20210406111622.1874957-3-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch cleans several checkpatch warnings in the peak_usb driver.
Link: https://lore.kernel.org/r/20210406111622.1874957-2-mkl@pengutronix.de
Acked-by: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds the core support for various USB CAN interfaces from
ETAS GmbH (https://www.etas.com/en/products/es58x.php). The next
patches add the glue code drivers for the individual interfaces.
Link: https://lore.kernel.org/r/20210410095948.233305-2-mailhol.vincent@wanadoo.fr
Co-developed-by: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Signed-off-by: Arunachalam Santhanam <arunachalam.santhanam@in.bosch.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Conflicts:
MAINTAINERS
- keep Chandrasekar
drivers/net/ethernet/mellanox/mlx5/core/en_main.c
- simple fix + trust the code re-added to param.c in -next is fine
include/linux/bpf.h
- trivial
include/linux/ethtool.h
- trivial, fix kdoc while at it
include/linux/skmsg.h
- move to relevant place in tcp.c, comment re-wrapped
net/core/skmsg.c
- add the sk = sk // sk = NULL around calls
net/tipc/crypto.c
- trivial
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
syzbot reported memory leak in peak_usb.
The problem was in case of failure after calling
->dev_init()[2] in peak_usb_create_dev()[1]. The data
allocated int dev_init() wasn't freed, so simple
->dev_free() call fix this problem.
backtrace:
[<0000000079d6542a>] kmalloc include/linux/slab.h:552 [inline]
[<0000000079d6542a>] kzalloc include/linux/slab.h:682 [inline]
[<0000000079d6542a>] pcan_usb_fd_init+0x156/0x210 drivers/net/can/usb/peak_usb/pcan_usb_fd.c:868 [2]
[<00000000c09f9057>] peak_usb_create_dev drivers/net/can/usb/peak_usb/pcan_usb_core.c:851 [inline] [1]
[<00000000c09f9057>] peak_usb_probe+0x389/0x490 drivers/net/can/usb/peak_usb/pcan_usb_core.c:949
Reported-by: syzbot+91adee8d9ebb9193d22d@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds "ONE-SHOT" mode support to the following CAN-USB
PEAK-System GmbH interfaces:
- PCAN-USB X6
- PCAN-USB FD
- PCAN-USB Pro FD
- PCAN-Chip USB
- PCAN-USB Pro
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
[mkl: split into two patches]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>