This fills in the GPU specific details for berlin
GPU cores so that the driver will work with them.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
These blocks need to be ungated for the other parts of
the driver properly initialize them (e.g., after a gpu
reset, etc.).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Since we aren't using it when the crtc is disabled, turn it off
to save power. The GRPH block is the part of the display
controller that controls the primary graphics plane (size,
address, etc.).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These fixes make writes work properly. Previously
only reads worked. Note that this feature is off
by default.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the LCD table contains an EDID record, properly account
for the edid size when walking through the records.
This should fix error messages about unknown LCD records.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Check the overrides in the firmware info table before
enabling spread spectrum on the engine or memory clocks.
Some boards may have valid spread spectrum tables, but
shouldn't necessarily have it enabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to allocate line buffer to each display when
setting up the watermarks. Failure to do so can lead
to a blank screen. This fixes blank screen problems
on dce8 asics.
Based on an initial fix from:
Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We need to allocate line buffer to each display when
setting up the watermarks. Failure to do so can lead
to a blank screen. This fixes blank screen problems
on dce6 asics.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=64850
Based on an initial fix from:
Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
We need to allocate line buffer to each display when
setting up the watermarks. Failure to do so can lead
to a blank screen. This fixes blank screen problems
on dce4.1/5 asics.
Based on an initial fix from:
Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Also add a new RADEON_INFO query to check that CP DMA packets are
supported on the compute ring.
CP DMA has been supported since the 3.8 kernel, but due to an oversight
we forgot to teach the CS checker that the CP DMA packet was legal for
the compute ring on Southern Islands GPUs.
This patch fixes a bug where the radeon driver will incorrectly reject a legal
CP DMA packet from user space. I would like to have the patch
backported to stable so that we don't have to require Mesa users to use a
bleeding edge kernel in order to take advantage of this feature which
is already present in the stable kernels (3.8 and newer).
v2:
- Don't bump kms version, so this patch can be backported to stable
kernels.
Cc: stable@vger.kernel.org
Signed-off-by: Tom Stellard <thomas.stellard@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that the CP is no longer reset and cg is properly
disabled in when appropriate in the dpm code we can
now enable mgcg (medium grained clockgating).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clockgating needs to be disabled around certain parts
of dpm setup otherwise the smc gets into a bad state
and dpm doesn't work properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clockgating needs to be disabled around certain parts
of dpm setup otherwise the smc gets into a bad state
and dpm doesn't work properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The format of the clearstate buffer used for pg (powergating)
changed between NI and SI. This formats it properly for what
the hardware expects on SI+.
v2: fix addresses
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clockgating requires signalling between the CP and the
RLC to work properly. Resetting the CP block in the
CP resume code messed up the internal coordination
between the blocks. Removing the reset allows gfx
clockgating to work properly. However, when gfx clock
gating is enabled, there is a strange interaction with
dpm which causes the chip to stay in the high performance
level all the time, so leave gfx clockgating disabled
for now.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- use new cg/pg flags for finer grained clock and
powergating control
- restructure the cg/pg code so it can be called from
other components such as dpm
v2: fix build breakage from rebase
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The format of the clearstate buffer used for pg (powergating)
changed between NI and SI. This formats it properly for what
the hardware expects on SI.
v2: fix addresses
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that the CP is no longer reset and cg is properly
disabled in when appropriate in the dpm code we can
now enable mgcg (medium grained clockgating).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clockgating needs to be disabled around certain parts
of dpm setup otherwise the smc gets into a bad state
and dpm doesn't work properly.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Clockgating requires signalling between the CP and the
RLC to work properly. Resetting the CP block in the
CP resume code messed up the internal coordination
between the blocks. Removing the reset allows gfx
clockgating to work properly. However, when gfx clock
gating is enabled, there is a strange interaction with
dpm which causes the chip to stay in the high performance
level all the time, so leave gfx clockgating disabled
for now.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Resturcture clockgating code so that it can be
enabled/disabled from other components such as
dpm.
v2: make function static
v3: add fine grained cg controls
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This commits adds flags for supported clockgating and
powergating features. This allows us to more easily
track which features are supported on a particular
asic and to enable/disable features for debugging.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This updates the audio driver to the speaker allocation
block from the EDID. A similar change was just implemented
for DCE4-8.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This updates the audio driver to the speaker allocation
block from the EDID. A similar change was just implemented
for DCE6/8.
v2: remove unused variables
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Do it before enabling audio channels (in AFMT_AUDIO_PACKET_CONTROL2
register).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Similar to DCE4/5, but supports multiple audio pins
which can be assigned per afmt block.
v2: rework the driver to handle more than one audio
pin.
v3: try different dto reg
v4: properly program dto
v5 (ck): change dto programming order
v6: program speaker allocation block
v7: rebase
v8: rebase on Rafał's changes
v9: integrated Rafał's comments, update to latest
drm_edid_to_speaker_allocation API
v10: add missing line break in error message
v11: add back audio enabled messages
v12: fix copy paste typo in r600_audio_enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Rafał Miłecki <zajec5@gmail.com>
Similar to separating the UVD code, just put the DMA
functions into separate files.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Our different hardware blocks are actually completely
separated, so it doesn't make much sense any more to
structure the code by pure chipset generations.
Start restructuring the code by separating our the UVD block.
v2: updated commit message
v3: rebased and restructurized start/stop functions for kv dpm.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Now that we have callbacks for [rw]ptr handling we can
remove the special handling for the DMA rings and use
the callbacks instead.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The hardware just doesn't support this correctly.
Disable it before we accidentally write anywhere we shouldn't.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Give the ring functions a separate structure and let the asic
structure point to the ring specific functions. This simplifies
the code and allows us to make changes at only one point.
No change in functionality.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to swap the data fetched over i2c properly. This
is the same fix as the endian fix for aux channel
transactions.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
According to the internal teams, we never hit the limit for
mclk switching on these asics, so we can disable the check.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The LCD has a relatively short vblank time (216us), but
the card is able to reclock memory fine in that time.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reported-by: normalrawr@gmail.com
Disable the UVD block when not in use to save power.
The block is not actually powergated on CI, but we
switch between UVD DPM (where the uvd clocks are
adjusted on demand) and clocks off.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
When we PG (powergate) UVD, we need to re-initialize it
before we can use it again.
v2: rebase on UVD stop fixes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Starting on CIK, multi-media blocks like UVD no longer
have special power state. Rather they have their own
DPM implementation which adjusts their clocks dynamically
when active. When they are not active, the blocks are
powergated to save power.
v2: add missing pm locks
v3: rebase on uvd state selection rework
v4: fix inverted logic typo noticed by Christian
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if we can switch the mclk during the vblank time otherwise
we may get artifacts on the screen when the mclk changes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for btc asics. This includes:
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen switching
Set radeon.dpm=1 to enable.
v2: remove unused radeon_atombios.c changes,
make missing smc ucode non-fatal
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This adds dpm support for KB/KV asics. This includes:
- dynamic engine clock scaling
- dynamic voltage scaling
- power containment
- shader power scaling
Set radeon.dpm=1 to enable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Internally we switched to using a separate header for
atombios pplib definitions. Switch over the open source
driver.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Calculate the low and high watermarks based on the low and high
clocks for the current power state. The dynamic pm hw will select
the appropriate watermark based on the internal dpm state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Newer asics have a lot of vram so it's less of an
issue to waste a little more space for the gart
page table. This gives us some additional gart space
before having to migrate to non-gart system ram
for games, etc. where we use up most of vram.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
1. Handle the the thermal state directly in the work handler.
Remove the state selection function since nothing else uses it now.
2. On some asics there is no thermal state, so we just use a regular
state and force the low performance state.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the UVD handle information to determine which
which power states to select when using UVD. For
example, decoding a single SD stream requires much
lower clocks than multiple HD streams.
v2: switch to a cleaner dpm/uvd interface
v3: change the uvd power state while streams
are active if need be
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a helper function for counting the number of open stream handles.
v2: fix copy-pasta in comments and whitespace error
v3: make function static since it's only used in radeon_uvd.c
at the moment
v4: make non-static again for future changes
v5: make static again for new rework of dpm uvd changes
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This lets drivers see the flags requested by the application
[airlied: fixup for rcar/imx/msm]
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
For optimus and powerxpress muxless we really want the GPU
driver deciding when to power up/down the GPU, not userspace.
This adds the ability for a driver to dynamically power up/down
the GPU and remove the switcheroo from controlling it, the
switcheroo reports the dynamic state to userspace also.
It also adds 2 power domains, one for machine where the power
switch is controlled outside the GPU D3 state, so the powerdown
ordering is done correctly, and the second for the hdmi audio
device to make sure it can resume for PCI config space accesses.
v1.1: fix build with switcheroo off
v2: add power domain support for radeon and v1 nvidia dsms
v2.1: fix typo in off case
v3: add audio power domain for hdmi audio + misc audio fixes
v4: use PCI_SLOT macro, drop power reference on hdmi audio resume
failure also.
Signed-off-by: Dave Airlie <airlied@redhat.com>
GEM does already a good job in tracking access to gem buffers via handles
and drm_vma access management. However, TTM drivers currently do not
verify this during mmap().
TTM provides the verify_access() callback to test this. So fix all drivers
to actually call into gem+vma to verify access instead of always returning
0.
All drivers assume that user-space can only get access to TTM buffers via
GEM handles. So whenever the verify_access() callback is called from
ttm_bo_mmap(), the buffer must have a valid embedded gem object. This is
true for all TTM+GEM drivers. But that's why this patch doesn't touch pure
TTM drivers (ie, vmwgfx).
v2: Switch to drm_vma_node_verify_access() to correctly return -EACCES if
access was denied.
Cc: Dave Airlie <airlied@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The new arch_phys_wc_add/del functions do the right thing both with
and without MTRR support in the kernel. So we can drop these
additional checks.
David Herrmann suggest to also kill the DRIVER_USE_MTRR flag since
it's now unused, which spurred me to do a bit a better audit of the
affected drivers. David helped a lot in that. Quoting our mail
discussion:
On Wed, Jul 10, 2013 at 5:41 PM, David Herrmann <dh.herrmann@gmail.com> wrote:
> On Wed, Jul 10, 2013 at 5:22 PM, Daniel Vetter <daniel.vetter@ffwll.ch> wrote:
>> On Wed, Jul 10, 2013 at 3:51 PM, David Herrmann <dh.herrmann@gmail.com> wrote:
>>>> -#if __OS_HAS_MTRR
>>>> -static inline int drm_core_has_MTRR(struct drm_device *dev)
>>>> -{
>>>> - return drm_core_check_feature(dev, DRIVER_USE_MTRR);
>>>> -}
>>>> -#else
>>>> -#define drm_core_has_MTRR(dev) (0)
>>>> -#endif
>>>> -
>>>
>>> That was the last user of DRIVER_USE_MTRR (apart from drivers setting
>>> it in .driver_features). Any reason to keep it around?
>>
>> Yeah, I guess we could rip things out. Which will also force me to
>> properly audit drivers for the eventual behaviour change this could
>> entail (in case there's an x86 driver which did not ask for an mtrr,
>> but iirc there isn't).
>
> david@david-mb ~/dev/kernel/linux $ for i in drivers/gpu/drm/* ; do if
> test -d "$i" ; then if ! grep -q USE_MTRR -r $i ; then echo $i ; fi ;
> fi ; done
> drivers/gpu/drm/exynos
> drivers/gpu/drm/gma500
> drivers/gpu/drm/i2c
> drivers/gpu/drm/nouveau
> drivers/gpu/drm/omapdrm
> drivers/gpu/drm/qxl
> drivers/gpu/drm/rcar-du
> drivers/gpu/drm/shmobile
> drivers/gpu/drm/tilcdc
> drivers/gpu/drm/ttm
> drivers/gpu/drm/udl
> drivers/gpu/drm/vmwgfx
> david@david-mb ~/dev/kernel/linux $
>
> So for x86 gma500,nouveau,qxl,udl,vmwgfx don't set DRIVER_USE_MTRR.
> But I cannot tell whether they break if we call arch_phys_wc_add/del,
> anyway. At least nouveau seemed to work here, but it doesn't use AGP
> or drm_bufs, I guess.
Cool, thanks a lot for stitching together the list of drivers to look
at. So for real KMS drivers it's the drives responsibility to add an
mtrr if it needs one. nouvea, radeon, mgag200, i915 and vmwgfx do that
already. Somehow the savage driver also ends up doing that, I have no
idea why.
Note that gma500 as a pure KMS driver doesn't need MTRR setup since
the platforms that it supports all support PAT. So no MTRRs needed to
get wc iomappings.
The mtrr support in the drm core is all for legacy mappings of garts,
framebuffers and registers. All legacy drivers set the USE_MTRR flag,
so we're good there.
All in all I think we can really just ditch this
/endquote
v2: Also kill DRIVER_USE_MTRR as suggested by David Herrmann
v3: Rebase on top of David Herrmann's agp setup/cleanup changes.
Cc: David Herrmann <dh.herrmann@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Acked-by: Andy Lutomirski <luto@amacapital.net>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
So I've stumbled over drm_fasync and wondered what it does. Digging
that up is quite a story.
First I've had to read up on what this does and ended up being rather
bewildered why peopled loved signals so much back in the days that
they've created SIGIO just for that ...
Then I wondered how this ever works, and what that strange "No-op."
comment right above it should mean. After all calling the core fasync
helper is pretty obviously not a noop. After reading through the
kernels FASYNC implementation I've noticed that signals are only sent
out to the processes attached with FASYNC by calling kill_fasync.
No merged drm driver has ever done that.
After more digging I've found out that the only driver that ever used
this is the so called GAMMA driver. I've frankly never heard of such a
gpu brand ever before. Now FASYNC seems to not have been the only bad
thing with that driver, since Dave Airlie removed it from the drm
driver with prejudice:
commit 1430163b4bbf7b00367ea1066c1c5fe85dbeefed
Author: Dave Airlie <airlied@linux.ie>
Date: Sun Aug 29 12:04:35 2004 +0000
Drop GAMMA DRM from a great height ...
Long story short, the drm fasync support seems to be doing absolutely
nothing. And the only user of it was never merged into the upstream
kernel. And we don't need any fops->fasync callback since the fcntl
implementation in the kernel already implements the noop case
correctly.
So stop this particular cargo-cult and rip it all out.
v2: Kill drm_fasync assignments in rcar (newly added) and imx drivers
(somehow I've missed that one in staging). Also drop the reference in
the drm DocBook. ARM compile-fail reported by Rob Clark.
v3: Move the removal of dev->buf_asnyc assignment in drm_setup to this
patch here.
v4: Actually git add ... tsk.
Cc: Dave Airlie <airlied@linux.ie>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Rob Clark <robdclark@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Again, it does nothing.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This field is never read. No need to set it in radeon. Besides, DRM gem
core clears it during setup, anyway.
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Merge the rcar stable branch that is being shared with the arm-soc tree.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* pfdo/drm-rcar-for-v3.12: (220 commits)
drm/rcar-du: Add FBDEV emulation support
drm/rcar-du: Add internal LVDS encoder support
drm/rcar-du: Configure RGB output routing to DPAD0
drm/rcar-du: Rework output routing support
drm/rcar-du: Add support for DEFR8 register
drm/rcar-du: Add support for multiple groups
drm/rcar-du: Fix buffer pitch alignment for R8A7790 DU
drm/rcar-du: Add support for the R8A7790 DU
drm/rcar-du: Move output routing configuration to group
drm/rcar-du: Remove register definitions for the second channel
drm/rcar-du: Use dynamic number of CRTCs instead of CRTCs array size
drm/rcar-du: Introduce CRTCs groups
drm/rcar-du: Rename rcar_du_plane_(init|register) to rcar_du_planes_*
drm/rcar-du: Create rcar_du_planes structure
drm/rcar-du: Rename platform data fields to match what they describe
drm/rcar-du: Merge LVDS and VGA encoder code
drm/rcar-du: Split VGA encoder and connector
drm/rcar-du: Split LVDS encoder and connector
drm/rcar-du: Clarify comment regarding plane Y source coordinate
drm/rcar-du: Support per-CRTC clock and IRQ
...
Conflicts:
drivers/gpu/drm/i915/i915_dma.c
drivers/gpu/drm/i915/intel_pm.c
drivers/gpu/drm/qxl/qxl_release.c
When the message buffer is currently moving block until it is idle again.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The smc ucode is required for dpm (dynamic power
management), but if it's missing just skip dpm setup
and don't disable acceleration.
Should fix:
https://bugs.freedesktop.org/show_bug.cgi?id=67876
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The rlc is required for dpm to work properly, so if
the rlc ucode is missing, don't enable dpm. Enabling
dpm without the rlc enabled can result in hangs.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We don't pin the BO on allocation, so don't unpin it on free.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Improve error handling in case userspace sends us
an invalid command buffer.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We also need to check the handle.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Otherwise just reinitialize from scratch on resume,
and so make it more likely to succeed.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For r6xx+ asics. This mirrors the behavior of pre-r6xx
asics. We need to program the MC even if something
else in startup() fails. Failure to do so results in
an unusable GPU.
Based on a fix from: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Need to set the wallclock ratio and adjust the phase
and module registers appropriately. May fix problems
with audio timing at certain display timings.
v2: properly handle clocks below 24mhz
v3: rebase r600 changes
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Removing the clock/power or resetting the VCPU can cause
hangs if that happens in the middle of a register write.
Stall the memory and register bus before putting the VCPU
into reset. Keep it in reset when unloading the module or
suspending.
Signed-off-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are some hardware issue with reclocking on SI when
UVD is active, so use a stable power state when UVD is
active. Fixes possible hangs and performance issues when
using UVD on SI.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to check for engine and memory clock ss separately
and only enable dynamic ss if either of them are found.
This should fix systems which have a ss table, but do
not have entries for engine or memory. On those systems
we may enable dynamic spread spectrum without enabling
it on the engine or memory clocks which can lead to a
hang in some cases.
fixes some systems reported here:
https://bugs.freedesktop.org/show_bug.cgi?id=66963
v2: fix typo
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
On rv770 and newer, clock gating is not required
for thermal protection. The only requirement is that
the design utilizes a thermal sensor.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There are two audio dtos on radeon asics that you can
select between. Normally, dto0 is used for hdmi and
dto1 for DP, but it seems that the dto is somehow
tied to the encoders on DCE3 asics.
fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=67435
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When we reset the GPU, we need to properly tear
down power management before reseting the GPU and then
set it back up again after reset. Add the missing
radeon_pm_[suspend|resume] calls to the gpu reset
function.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is no need to pass constants via stack. The width may be explicitly
specified in the format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: David Herrmann <dh.herrmann@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Because, there is no reason for it not to be const.
v1: original
v2: fix compile break in vmwgfx, and couple related cleanups suggested
by Ville Syrjälä
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
All the gem based kms drivers really want the same function to
destroy a dumb framebuffer backing storage object.
So give it to them and roll it out in all drivers.
This still leaves the option open for kms drivers which don't use GEM
for backing storage, but it does decently simplify matters for gem
drivers.
Acked-by: Inki Dae <inki.dae@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Intel Graphics Development <intel-gfx@lists.freedesktop.org>
Cc: Ben Skeggs <skeggsb@gmail.com>
Reviwed-by: Rob Clark <robdclark@gmail.com>
Cc: Alex Deucher <alexdeucher@gmail.com>
Acked-by: Patrik Jakobsson <patrik.r.jakobsson@gmail.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The ProcessAuxChannel table on some rv635 boards assumes
the divmul members are initialized to 0 otherwise we get
an invalid fb offset since it has a bad mask set when
setting the fb base. While here initialize all the
atom interpretor elements to 0.
Fixes:
https://bugzilla.kernel.org/show_bug.cgi?id=60639
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The SMC interface changed compared to Cayman and
previous asics. Set the enabled levels properly
and enable reclocking by default when dpm is enabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Disable cac setup on SI for now since it causes
strange performance level restrictions on certain
cards. I suspect there may be issues with some of
the 64 bit fixed point double emulation that is used
to set up those parameters. I need to double check
the math before this can be re-enabled.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Coarse grain clockgating causes problems with reclocking on
some cards and powergating (verde only) causes problems with
ring initialization. The proper fix (restructuring the init
sequences) is too invasive for 3.11 so just disable them for
now.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For correctness. The fb divider isn't actually used
in any of the relevant dpm code. It's calculated
from the other parameters.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Don't try and enable clockgating if the asic doesn't have
UVD. Use rdev->has_uvd rather than using local checks.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Need to set the DISP*_GAP fields as well as the
DISP*_GAP_MCHG fields. Same as on previous asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to set the dto source before setting the
dividers otherwise we may get stability problems
with the dto leading to audio playback problems.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Cc: stable@vger.kernel.org
Need to use the driver state rather than the register
state since the displays may not be enabled when the
power state is programmed.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use the new vma-manager infrastructure. This doesn't change any
implementation details as the vma-offset-manager is nearly copied 1-to-1
from TTM.
The vm_lock is moved into the offset manager so we can drop it from TTM.
During lookup, we use the vma locking helpers to take a reference to the
found object.
In all other scenarios, locking stays the same as before. We always
guarantee that drm_vma_offset_remove() is called only during destruction.
Hence, helpers like drm_vma_node_offset_addr() are always safe as long as
the node has a valid offset.
This also drops the addr_space_offset member as it is a copy of vm_start
in vma_node objects. Use the accessor functions instead.
v4:
- remove vm_lock
- use drm_vma_offset_lock_lookup() to protect lookup (instead of vm_lock)
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Martin Peres <martin.peres@labri.fr>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Signed-off-by: David Herrmann <dh.herrmann@gmail.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Last driver and pretty obviously a major user of this little function.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Really, this is all old-style stuff and just copy-pasta from the
ums driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
No need to create a dummy ioctl function to return -EINVAL, since
that's what the core already does in the absence of the dma_ioctl
callback. So we can safely remove this.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Dave Airlie <airlied@gmail.com>
Noticed that my old Radeon 7500 hung after printing
drm: GPU not posted. posting now...
when it wasn't selected as the primary card the BIOS. Some digging
revealed that it was hanging in combios_parse_mmio_table() while
parsing the ASIC INIT 3 table. Looking at the BIOS ROM for the card,
it becomes obvious that there is no ASIC INIT 3 table in the BIOS.
The code is just processing random garbage. No surprise it hangs!
Why do I say that there is no ASIC INIT 3 table is the BIOS? This
table is found through the MISC INFO table. The MISC INFO table can
be found at offset 0x5e in the COMBIOS header. But the header is
smaller than that. The COMBIOS header starts at offset 0x126. The
standard PCI Data Structure (the bit that starts with 'PCIR') lives at
offset 0x180. That means that the COMBIOS header can not be larger
than 0x5a bytes and therefore cannot contain a MISC INFO table.
I looked at a dozen or so BIOS images, some my own, some downloaded from:
<http://www.techpowerup.com/vgabios/index.php?manufacturer=ATI&page=1>
It is fairly obvious that the size of the COMBIOS header can be found
at offset 0x6 of the header. Not sure if it is a 16-bit number or
just an 8-bit number, but that doesn't really matter since the tables
seems to be always smaller than 256 bytes.
So I think combios_get_table_offset() should check if the requested
table is present. This can be done by checking the offset against the
size of the header. See the diff below. The diff is against the WIP
OpenBSD codebase that roughly corresponds to Linux 3.8.13 at this
point. But I don't think this bit of the code changed much since
then.
For what it is worth:
Signed-off-by: Mark Kettenis <kettenis@openbsd.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Hopefully avoid more quirks in the future due to bogus
vbios dac data.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Hello,
got another card with "too bright" problem:
Sapphire Radeon VE 7000 DDR (VGA+S-Video)
lspci -vnn:
01:00.0 VGA compatible controller [0300]: Advanced Micro Devices [AMD] nee ATI RV100 QY [Radeon 7000/VE] [1002:5159] (prog-if 00 [VGA controller])
Subsystem: PC Partner Limited Sapphire Radeon VE 7000 DDR [174b:7c28]
The patch below fixes the problem for this card.
But I don't like the blacklist, couldn't some heuristic be used instead?
The interesting thing is that the manufacturer is the same as the other card
needing the same quirk. I wonder how many different types are broken this way.
The "wrong" ps2_pdac_adj value that comes from BIOS on this card is 0x300.
====================
drm/radeon: Add primary dac adj quirk for Sapphire Radeon VE 7000 DDR
Values from BIOS are wrong, causing too bright colors.
Use default values instead.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The atom interpreter expects data in LE format, so
swap the message buffer as apprioriate.
v2: properly handle non-dw aligned byte counts.
v3: properly handle remainder
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Dong He <hedonghust@gmail.com>
Cc: stable@vger.kernel.org
Make sure the 3D engine is idle before using CP DMA for
bo copies.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Marek Olšák <maraeo@gmail.com>
This allows you to look at the current DPM state via
debugfs.
Due to the way the hardware works on these asics, there's
no way to look up exactly what power state we are in, so
we make the best guess we can based on the current sclk.
v2: Anthoine's version
v3: fix ref div
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
More DPM fixes, r6xx DMA fix for bo moving, UVD fixes,
one major regression fix on bootup on some machine (ttm backoff missing)
* 'drm-fixes-3.11' of git://people.freedesktop.org/~agd5f/linux:
radeon kms: do not flush uninitialized hotplug work
drm/radeon/dpm/sumo: handle boost states properly when forcing a perf level
drm/radeon: align VM PTBs (Page Table Blocks) to 32K
drm/radeon: allow selection of alignment in the sub-allocator
drm/radeon: never unpin UVD bo v3
drm/radeon: fix UVD fence emit
drm/radeon: add fault decode function for CIK
drm/radeon: add fault decode function for SI (v2)
drm/radeon: add fault decode function for cayman/TN (v2)
drm/radeon: use radeon device for request firmware
drm/radeon: add missing ttm_eu_backoff_reservation to radeon_bo_list_validate
drm/radeon: use CP DMA on r6xx for bo moves
drm/radeon: implement bo copy callback using CP DMA (v2)
drm/radeon: Disable dma rings for bo moves on r6xx
drm/radeon/dpm: disable gfx PG on PALM
drm/radeon/hdmi: make sure we have an afmt block assigned
Need to properly enable/disable boost states when forcing a performance
level.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Covers requirements of all current asics.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
There are cases where we need more than 4k alignment. No
functional change with this commit.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Changing the UVD BOs offset on suspend/resume doesn't work because the VCPU
internally keeps pointers to it. Just keep it always pinned and save the
content manually.
Fixes: https://bugs.freedesktop.org/show_bug.cgi?id=66425
v2: fix compiler warning
v3: fix CIK support
Note: a version of this patch needs to go to stable.
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Currently doesn't matter cause we allocate the fence in the
lower 265MB anyway.
Reported-by: Frank Huang <FrankR.Huang@amd.com>
Signed-off-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Helpful for debugging GPUVM errors as we can see what
hw block and page generated the fault in the log.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Helpful for debugging GPUVM errors as we can see what
hw block and page generated the fault in the log.
v2: simplify fault decoding
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Helpful for debugging GPUVM errors as we can see what
hw block and page generated the fault in the log.
v2: simplify fault decoding
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Avoid creating temporary platform device that will lead to issue
when several radeon gpu are in same computer. Instead directly use
the radeon device for requesting firmware.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Op 10-07-13 12:03, Markus Trippelsdorf schreef:
> On 2013.07.10 at 11:56 +0200, Maarten Lankhorst wrote:
>> Op 10-07-13 11:46, Markus Trippelsdorf schreef:
>>> On 2013.07.10 at 11:29 +0200, Maarten Lankhorst wrote:
>>>> Op 10-07-13 11:22, Markus Trippelsdorf schreef:
>>>>> By simply copy/pasting a big document under LibreOffice my system hangs
>>>>> itself up. Only a hard reset gets it working again.
>>>>> see also: https://bugs.freedesktop.org/show_bug.cgi?id=66551
>>>>>
>>>>> I've bisected the issue to:
>>>>>
>>>>> commit ecff665f5e
>>>>> Author: Maarten Lankhorst <m.b.lankhorst@gmail.com>
>>>>> Date: Thu Jun 27 13:48:17 2013 +0200
>>>>>
>>>>> drm/ttm: make ttm reservation calls behave like reservation calls
>>>>>
>>>>> This commit converts the source of the val_seq counter to
>>>>> the ww_mutex api. The reservation objects are converted later,
>>>>> because there is still a lockdep splat in nouveau that has to
>>>>> resolved first.
>>>>>
>>>>> Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
>>>>> Reviewed-by: Jerome Glisse <jglisse@redhat.com>
>>>>> Signed-off-by: Dave Airlie <airlied@redhat.com>
>>>> Hey,
>>>>
>>>> Can you try current head with CONFIG_PROVE_LOCKING set and post the
>>>> lockdep splat from dmesg, if any? If there is any locking issue
>>>> lockdep should warn about it. Lockdep will turn itself off after the
>>>> first splat, so if the lockdep splat happens before running the
>>>> affected parts those will have to be fixed first.
>>> There was an unrelated EDAC lockdep splat, so I simply disabled it.
>>>
>>> This is what I get:
>>>
>>> Jul 10 11:40:44 x4 kernel: ================================================
>>> Jul 10 11:40:44 x4 kernel: [ BUG: lock held when returning to user space! ]
>>> Jul 10 11:40:44 x4 kernel: 3.10.0-08587-g496322b #35 Not tainted
>>> Jul 10 11:40:44 x4 kernel: ------------------------------------------------
>>> Jul 10 11:40:44 x4 kernel: X/211 is leaving the kernel with locks still held!
>>> Jul 10 11:40:44 x4 kernel: 2 locks held by X/211:
>>> Jul 10 11:40:44 x4 kernel: #0: (reservation_ww_class_acquire){+.+.+.}, at: [<ffffffff813279f0>] radeon_bo_list_validate+0x20/0xd0
>>> Jul 10 11:40:44 x4 kernel: #1: (reservation_ww_class_mutex){+.+.+.}, at: [<ffffffff81309306>] ttm_eu_reserve_buffers+0x126/0x4b0
>>> Jul 10 11:40:52 x4 kernel: SysRq : Emergency Sync
>>> Jul 10 11:40:53 x4 kernel: Emergency Sync complete
>>>
>> Thanks, exactly what I thought. I missed a backoff somewhere..
>>
>> Does the below patch fix it?
> Yes. Thank you for your quick reply.
8<------
If radeon_cs_parser_relocs fails ttm_eu_backoff_reservation doesn't get called.
This left open a bug where ttm_eu_reserve_buffers succeeded but the bo's were
not unlocked afterwards:
Jul 10 11:40:44 x4 kernel: ================================================
Jul 10 11:40:44 x4 kernel: [ BUG: lock held when returning to user space! ]
Jul 10 11:40:44 x4 kernel: 3.10.0-08587-g496322b #35 Not tainted
Jul 10 11:40:44 x4 kernel: ------------------------------------------------
Jul 10 11:40:44 x4 kernel: X/211 is leaving the kernel with locks still held!
Jul 10 11:40:44 x4 kernel: 2 locks held by X/211:
Jul 10 11:40:44 x4 kernel: #0: (reservation_ww_class_acquire){+.+.+.}, at: [<ffffffff813279f0>] radeon_bo_list_validate+0x20/0xd0
Jul 10 11:40:44 x4 kernel: #1: (reservation_ww_class_mutex){+.+.+.}, at: [<ffffffff81309306>] ttm_eu_reserve_buffers+0x126/0x4b0
Jul 10 11:40:52 x4 kernel: SysRq : Emergency Sync
Jul 10 11:40:53 x4 kernel: Emergency Sync complete
This is a regression caused by commit ecff665f5e.
"drm/ttm: make ttm reservation calls behave like reservation calls"
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lighter weight than using the 3D engine.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Lighter weight than using the 3D engine.
v2: fix ring count
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
They still seem to cause instability on some r6xx parts.
As a follow up, we can switch to using CP DMA for bo
moves on r6xx as a lighter weight alternative to using
the 3D engine.
A version of this patch should also go to stable kernels.
Tested-by: J.N. <golden.fleeced@gmail.com>
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Gfx PG doesn't seem to work properly when UVD is initialized
on certain PALM boards. Disable gfx PG for now until we sort
out a proper fix.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull drm updates from Dave Airlie:
"Okay this is the big one, I was stalled on the fbdev pull req as I
stupidly let fbdev guys merge a patch I required to fix a warning with
some patches I had, they ended up merging the patch from the wrong
place, but the warning should be fixed. In future I'll just take the
patch myself!
Outside drm:
There are some snd changes for the HDMI audio interactions on haswell,
they've been acked for inclusion via my tree. This relies on the
wound/wait tree from Ingo which is already merged.
Major changes:
AMD finally released the dynamic power management code for all their
GPUs from r600->present day, this is great, off by default for now but
also a huge amount of code, in fact it is most of this pull request.
Since it landed there has been a lot of community testing and Alex has
sent a lot of fixes for any bugs found so far. I suspect radeon might
now be the biggest kernel driver ever :-P p.s. radeon.dpm=1 to enable
dynamic powermanagement for anyone.
New drivers:
Renesas r-car display unit.
Other highlights:
- core: GEM CMA prime support, use new w/w mutexs for TTM
reservations, cursor hotspot, doc updates
- dvo chips: chrontel 7010B support
- i915: Haswell (fbc, ips, vecs, watermarks, audio powerwell),
Valleyview (enabled by default, rc6), lots of pll reworking, 30bpp
support (this time for sure)
- nouveau: async buffer object deletion, context/register init
updates, kernel vp2 engine support, GF117 support, GK110 accel
support (with external nvidia ucode), context cleanups.
- exynos: memory leak fixes, Add S3C64XX SoC series support, device
tree updates, common clock framework support,
- qxl: cursor hotspot support, multi-monitor support, suspend/resume
support
- mgag200: hw cursor support, g200 mode limiting
- shmobile: prime support
- tegra: fixes mostly
I've been banging on this quite a lot due to the size of it, and it
seems to okay on everything I've tested it on."
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (811 commits)
drm/radeon/dpm: implement vblank_too_short callback for si
drm/radeon/dpm: implement vblank_too_short callback for cayman
drm/radeon/dpm: implement vblank_too_short callback for btc
drm/radeon/dpm: implement vblank_too_short callback for evergreen
drm/radeon/dpm: implement vblank_too_short callback for 7xx
drm/radeon/dpm: add checks against vblank time
drm/radeon/dpm: add helper to calculate vblank time
drm/radeon: remove stray line in old pm code
drm/radeon/dpm: fix display_gap programming on rv7xx
drm/nvc0/gr: fix gpc firmware regression
drm/nouveau: fix minor thinko causing bo moves to not be async on kepler
drm/radeon/dpm: implement force performance level for TN
drm/radeon/dpm: implement force performance level for ON/LN
drm/radeon/dpm: implement force performance level for SI
drm/radeon/dpm: implement force performance level for cayman
drm/radeon/dpm: implement force performance levels for 7xx/eg/btc
drm/radeon/dpm: add infrastructure to force performance levels
drm/radeon: fix surface setup on r1xx
drm/radeon: add support for 3d perf states on older asics
drm/radeon: set default clocks for SI when DPM is disabled
...
Check if we can switch the mclk during the vblank time otherwise
we may get artifacts on the screen when the mclk changes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if we can switch the mclk during the vblank time otherwise
we may get artifacts on the screen when the mclk changes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if we can switch the mclk during the vblank time otherwise
we may get artifacts on the screen when the mclk changes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if we can switch the mclk during the vblank time otherwise
we may get artifacts on the screen when the mclk changes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if we can switch the mclk during the vblank time otherwise
we may get artifacts on the screen when the mclk changes.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the vblank time is too short to adjust mclk,
assume multiple displays (no mclk adjustments).
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This allows you to force specific power levels within a power
state. Due to hardware restrictions between generations, the
interface is limited to the following 3 selections:
auto: all levels enabled
low: forced to the lowest power level
high: forced to the highest power level
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
r1xx asics have a slightly different surface register
setup compared to newer asics. There is no specific
enable bit for macro tiling, rather, to disable macro
tiling, you need to set the surface pitch to 0.
With this fixed, the special rn50 handling can go.
Noticed-by: Mark Kettenis <mark.kettenis@xs4all.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Certain older rv770 asics have both a performance and
a 3D performance state rather than just multiple performance
levels in the state power state. The current code would
select the performance state rather than the 3D performance
state when the "performance" profile was selected. This change
switches to the "balanced" profile by default which ends up being
the internal performance profile. When the user selects the
"performance" profile, it selects the internal 3D performance
state so the user can select the higher performance modes.
For most asics this changes nothing. For certain rv770 asics
with static performance and 3D performance states, this allows
you to select between then using by selecting the "balanced"
and "performance" dpm profiles.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fix patching of vddc values for SI and enable manually forcing
clocks to default levels as per NI.
This improves the out of the box performance with SI asics.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For chips without debugfs dpm support say that it's not
implemented rather than not supported to avoid confusion
about DPM support in general.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Was disabled due to stability issues on certain boards
caused by the a bug in the parsing of the atom mc reg tables.
That's fixed now so re-enable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Was disabled due to stability issues on certain boards
caused by the a bug in the parsing of the atom mc reg tables.
That's fixed now so re-enable.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Try to use lockdep_assert_held or other alternatives where possible.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This commit converts the source of the val_seq counter to
the ww_mutex api. The reservation objects are converted later,
because there is still a lockdep splat in nouveau that has to
resolved first.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Reviewed-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is the pull request for radeon for 3.11. Highlights include:
- Support for CIK (Sea Islands) asics: 3D, compute, UVD
- DPM (Dynamic Power Management) support for 6xx-SI
- ASPM support for 6xx-SI
- Assorted bug fixes
* 'drm-next-3.11' of git://people.freedesktop.org/~agd5f/linux: (168 commits)
drm/radeon/SI: fix TDP adjustment in set_power_state
drm/radeon/NI: fix TDP adjustment in set_power_state
drm/radeon: fix endian issues in atombios dpm code
drm/radeon/dpm: fix UVD clock setting on SI
drm/radeon/dpm: fix UVD clock setting on cayman
drm/radeon/dpm: add support for setting UVD clock on rv6xx
drm/radeon/dpm: add support for setting UVD clock on rs780
drm/radeon: fix typo in ni_print_power_state
drm/radeon: fix typo in cik_select_se_sh()
drm/radeon/si: fix typo in function name
drm/radeon/dpm: fix typo in setting uvd clock
drm/radeon/dpm: add dpm_set_power_state failure output (si)
add dpm_set_power_state failure output (7xx-ni)
drm/radeon/dpm: add dpm_set_power_state failure output (7xx-ni)
drm/radeon/dpm: add dpm_enable failure output (si)
drm/radeon/dpm: add dpm_enable failure output (7xx-ni)
drm/radeon/kms: add dpm support for SI (v7)
drm/radeon: switch SI to use radeon_ucode.h
drm/radeon: add SI to r600_is_internal_thermal_sensor()
drm/radeon/dpm/rs780: properly catch errors in dpm setup
...
This adds dpm support for SI asics. This includes:
- dynamic engine clock scaling
- dynamic memory clock scaling
- dynamic voltage scaling
- dynamic pcie gen1/gen2/gen3 switching
- power containment
- shader power scaling
Set radeon.dpm=1 to enable.
v2: enable hainan support, rebase
v3: guard acpi stuff
v4: fix 64 bit math
v5: fix 64 bit div harder
v6: fix thermal interrupt check noticed by Jerome
v7: attempt fix state enable
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Add a helper function to determine the preferred
pcie gen based on the card, system, and circumstance.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Validate the voltages against the voltage requirements of the
dispclk. We currently don't adjust the disp clock so it never
changes, but we need to filter out voltage levels that are too
low none the less.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
