Add tcpm_port_error_recovery symbol and corresponding event that runs in
tcpm_pd_event handler to set the port to the ERROR_RECOVERY state. tcpci
drivers can use the symbol to reset the port when tcpc faults affect port
functionality.
Signed-off-by: RD Babiera <rdbabiera@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231121203845.170234-5-rdbabiera@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The TPS6598x PD controller provides an active-high hardware reset input
that reinitializes all device settings. If it is not grounded by
design, the driver must be able to de-assert it in order to initialize
the device.
The PD controller is not ready for registration right after the reset
de-assertion and a delay must be introduced in that case. According to
TI, the delay can reach up to 1000 ms [1], which is in line with the
experimental results obtained with a TPS65987D.
Add a GPIO descriptor for the reset signal and basic reset management
for initialization and suspend/resume.
[1] https://e2e.ti.com/support/power-management-group/power-management/
f/power-management-forum/1269856/tps65987d-tps65987d-reset-de-assert-
to-normal-operation/4809389#4809389
Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Link: https://lore.kernel.org/r/20230912-topic-tps6598x_reset-v3-1-0c2873070a77@wolfvision.net
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some USB devices we might want to do something different for
usb_choose_configuration(). One example here is the r8152 driver where
we want to end up using the vendor driver with the preferred
interface.
The r8152 driver tried to make things work by implementing a USB
generic_subclass driver and then overriding the normal config
selection after it happened. This is less than ideal and also caused
breakage if someone deauthorized and re-authorized the USB device
because the USB core ended up going back to it's default logic for
choosing the best config. I made an attempt to fix this [1] but it was
a bit ugly.
Let's do this better and allow USB generic_subclass drivers to
override usb_choose_configuration().
[1] https://lore.kernel.org/r/20231130154337.1.Ie00e07f07f87149c9ce0b27ae4e26991d307e14b@changeid
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231201102946.v2.2.Iade5fa31997f1a0ca3e1dec0591633b02471df12@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no real reason that subclassed USB drivers _need_ to define
probe() since they might want to subclass for some other reason. Make
it optional to define probe() if we're a generic_subclass.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231201102946.v2.1.I7ea0dd55ee2acdb48b0e6d28c1a704ab2c29206f@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() has the documented, but still rather strange trait of
returning the length of the data that *would have been* written to the
array if space were available, rather than the arguably more useful
length of data *actually* written, it is usually considered wise to use
something else instead in order to avoid confusion.
In the case of sysfs call-backs, new wrappers exist that do just that.
This patch replaces just one use of snprintf() found in the sysfs
.show() call-back with the new sysfs_emit() helper.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Dmitry Bogdanov <d.bogdanov@yadro.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-6-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() has the documented, but still rather strange trait of
returning the length of the data that *would have been* written to the
array if space were available, rather than the arguably more useful
length of data *actually* written, it is usually considered wise to use
something else instead in order to avoid confusion.
In the case of sysfs call-backs, new wrappers exist that do just that.
This patch replaces just one use of snprintf() found in the sysfs
.show() call-back with the new sysfs_emit() helper.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-5-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
The uses in this file both seem to assume that data *has been* written!
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Yuan-Hsin Chen <yhchen@faraday-tech.com>
Cc: Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Po-Yu Chuang <ratbert.chuang@gmail.com>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-4-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a general misunderstanding amongst engineers that {v}snprintf()
returns the length of the data *actually* encoded into the destination
array. However, as per the C99 standard {v}snprintf() really returns
the length of the data that *would have been* written if there were
enough space for it. This misunderstanding has led to buffer-overruns
in the past. It's generally considered safer to use the {v}scnprintf()
variants in their place (or even sprintf() in simple cases). So let's
do that.
The uses in this file all seem to assume that data *has been* written!
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Pawel Laszczak <pawell@cadence.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-3-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since snprintf() has the documented, but still rather strange trait of
returning the length of the data that *would have been* written to the
array if space were available, rather than the arguably more useful
length of data *actually* written, it is usually considered wise to use
something else instead in order to avoid confusion.
In the case of sysfs call-backs, new wrappers exist that do just that.
This patch replaces the 2 uses of snprintf() found in the sysfs .show()
call-backs with the new sysfs_emit() helpers. Whist we're at it, let's
replace the sprintf()s as well. For no other reason than consistency.
Link: https://lwn.net/Articles/69419/
Link: https://github.com/KSPP/linux/issues/105
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Damien Bergamini <damien.bergamini@free.fr>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Lee Jones <lee@kernel.org>
Link: https://lore.kernel.org/r/20231130105459.3208986-2-lee@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is a short gap between urb being submitted and actually added to the
endpoint queue (linked). If the device is disconnected during this time
then usb core is not yet aware of the pending urb, and device may be freed
just before xhci_urq_enqueue() continues, dereferencing the freed device.
Freeing the device is protected by the xhci spinlock, so make sure we take
and keep the lock while checking that device exists, dereference it, and
add the urb to the queue.
Remove the unnecessary URB check, usb core checks it before calling
xhci_urb_enqueue()
Suggested-by: Kuen-Han Tsai <khtsai@google.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-20-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The max packet size for full speed control endpoint 0 may vary. It is
defined in the device descriptor, which is read using the same endpoint.
Usb core sets a temporary max packet size value until the real value is
read.
xhci driver needs to reconfigure the endpoint context seen by the
controller if the max packet size changes.
It makes more sense to do this reconfiguration in xhci_endpoint_reset()
instead of urb enqueue as usb core will call endpoint reset during
enumeration if the max packet values differ.
Max packet size adjustment for endpoint 0 can only happen once per
device enumeration.
Previously the max packet size was checked during every urb enqueue.
This is an additional check for every enqueued urb, and also turned out
to have locking issues as urbs may be queued in any context while xhci
max packet size reconfiguration requires memory allocation, locking, and
sleeping.
Tested with a full speed device using both old and new scheme enumeration
and an intentionally incorrect preliminary max packet size value.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-19-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove extra spaces/indentation and add spaces where required.
This commit does not change any functionality.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-18-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify 'xhci_try_enable_msi()' and reduce unnecessary function calls.
xHCI driver first tries to allocate 'num_online_cpu()' number of MSI-X
vectors, if that fails it falls back to a single MSI vector. There is no
good reason for this, we currently only support a primary interrupter.
However, we are still interested in knowing if there are more vectors
available, which will be utilized once we get secondary interrupter
support.
Call 'pci_alloc_irq_vectors()' once (with MSI-X and MSI flag), instead
of separately for MSI-X and MSI. And accept any number of MSI-X or MSI
vectors between 1 and 'num_online_cpu()'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-17-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of variable 'msix_count' containing the number of MSI-X vectors,
now it can contains MSI or MSI-X vector amount. Because both interrupt
methods allow several vectors. Thus, 'msix_count' is renamed to 'nvecs'.
Additionally, instead of storing the maximum possible vector amount,
now it stores the amount of successfully allocated vectors, or negative
integer on allocation failure.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-16-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current way the xhci driver sets up MSI interrupts is overly complex
and messy. The whole MSI setup can be done in one simple function.
Continue refactoring MSI/MSI-X setup by incorporating 'xhci_setup_msi()'
into 'xhci_try_enable_msi()'. Now all interrupt enabling is contained in
one function, which should make it easier to rework.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-15-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current way the xhci driver sets up MSI/MSI-X interrupts is overly
complex and messy. The whole MSI/MSI-X setup can be done in one simple
function.
Start refactoring this by incorporating 'xhci_setup_msix()' into
'xhci_try_enable_msi()'. 'xhci_setup_msix()' is a static function which
is only called by 'xhci_try_enable_msi()'.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-14-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current xHCI driver only supports one "interrupter", meaning we will
only use one MSI/MSI-X interrupt line. Thus, add handler only to the
first interrupt line.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Co-developed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-13-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move the error check "No MSI-X/MSI found and no IRQ in BIOS" inside
'goto legacy'. It is better to check if the IRQ interrupt is available,
before trying to add a handler. Additionally the aforementioned error
message is much more clear.
Signed-off-by: Niklas Neronin <niklas.neronin@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-12-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is preferred to use sizeof(*pointer) instead of sizeof(type).
The type of the variable can change and one needs not change
the former (unlike the latter). No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-10-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Replace the custom return value with proper Linux error code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-8-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kstrtox() along with regmap API can return different error codes
based on the circumstances. Don't shadow them when returning to
the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-7-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usual pattern is to check for errors and then continue if none.
Apply that pattern to xhci_dbc_stop() code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-6-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Embrace ATTRIBUTE_GROUPS() to avoid boiler plate code.
This should not introduce any functional changes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-5-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Follow the advice of the Documentation/filesystems/sysfs.rst and show()
should only use sysfs_emit() or sysfs_emit_at() when formatting the
value to be returned to user space.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-4-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's standard approach to parse values from user space by using
sysfs_streq(). Make driver use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-3-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dma_free_coherent() is NULL-aware, not necessary to check for
the parameter twice. Drop duplicate conditionals in the caller.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231201150647.1307406-2-mathias.nyman@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Cypress CY7C6563x is a 2/4-port USB 2.0 hub. Add support for
this hub in the driver in order to bring up reset, supply or clock
dependencies.
There is no reset pulse width given in the datasheet so we expect
a minimal value of 1us to be enough. This hasn't been tested though
due to lack of hardware which has the reset connected to a GPIO.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20231127112234.109073-3-frieder@fris.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Most onboard USB hubs have a dedicated crystal oscillator but on some
boards the clock signal for the hub is provided by the SoC.
In order to support this, we add the possibility of specifying a
clock in the devicetree that gets enabled/disabled when the hub
is powered up/down.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20231127112234.109073-2-frieder@fris.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of printing the decimal error codes, let's use the more
human-readable symbolic error names provided by the %pe printk
format specifier.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/r/20231127112234.109073-1-frieder@fris.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the USB/PHY/Thunderbolt fixes in here as well for later patches
to build on top of.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a couple of modem device entry fixes and some new modem device
ids.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCZWBhzwAKCRALxc3C7H1l
COqFAP4uRs5B1dsUxOHQ8HpsbBTmCE9/iFd0k/vegyGqTWd6CAD+LFjP7ySTm+2D
p5RkbllxNh+rHSeo2DFxnM27bXvmvQE=
=nvJ4
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-6.7-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for 6.7-rc3
Here are a couple of modem device entry fixes and some new modem device
ids.
All have been in linux-next with no reported issues.
* tag 'usb-serial-6.7-rc3' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (329 commits)
USB: serial: option: add Luat Air72*U series products
USB: serial: option: add Fibocom L7xx modules
USB: serial: option: fix FM101R-GL defines
USB: serial: option: don't claim interface 4 for ZTE MF290
Linux 6.7-rc2
prctl: Disable prctl(PR_SET_MDWE) on parisc
parisc/power: Fix power soft-off when running on qemu
parisc: Replace strlcpy() with strscpy()
NFSD: Fix checksum mismatches in the duplicate reply cache
NFSD: Fix "start of NFS reply" pointer passed to nfsd_cache_update()
NFSD: Update nfsd_cache_append() to use xdr_stream
nfsd: fix file memleak on client_opens_release
dm-crypt: start allocating with MAX_ORDER
dm-verity: don't use blocking calls from tasklets
dm-bufio: fix no-sleep mode
dm-delay: avoid duplicate logic
dm-delay: fix bugs introduced by kthread mode
dm-delay: fix a race between delay_presuspend and delay_bio
drm/amdgpu/gmc9: disable AGP aperture
drm/amdgpu/gmc10: disable AGP aperture
...
When we use an async work queue to perform the function of pumping
usb requests to the usb controller, it is possible that amongst other
factors, thread scheduling affects at what cadence we're able to pump
requests. This could mean isoc usb requests miss their uframes - resulting
in video stream flickers on the host device.
To avoid this, we make the async_wq thread only produce isoc usb_requests
with uvc buffers encoded into them. The process of queueing to the
endpoint is done by the uvc_video_complete() handler. In case no
usb_requests are ready with encoded information, we just queue a zero
length request to the endpoint from the complete handler.
For bulk endpoints the async_wq thread still queues usb requests to the
endpoint.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Jayant Chowdhary <jchowdhary@google.com>
Suggested-by: Avichal Rakesh <arakesh@google.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231120062026.3759463-1-jchowdhary@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the uvc gadget driver allocates all uvc_requests as one array
and deallocates them all when the video stream stops. This includes
de-allocating all the usb_requests associated with those uvc_requests.
This can lead to use-after-free issues if any of those de-allocated
usb_requests were still owned by the usb controller.
This is patch 2 of 2 in fixing the use-after-free issue. It adds a new
flag to uvc_video to track when frames and requests should be flowing.
When disabling the video stream, the flag is tripped and, instead
of de-allocating all uvc_requests and usb_requests, the gadget
driver only de-allocates those usb_requests that are currently
owned by it (as present in req_free). Other usb_requests are left
untouched until their completion handler is called which takes care
of freeing the usb_request and its corresponding uvc_request.
Now that uvc_video does not depends on uvc->state, this patch removes
unnecessary upates to uvc->state that were made to accommodate uvc_video
logic. This should ensure that uvc gadget driver never accidentally
de-allocates a usb_request that it doesn't own.
Link: https://lore.kernel.org/7cd81649-2795-45b6-8c10-b7df1055020d@google.com
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Suggested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20231109004104.3467968-4-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch refactors the video disable logic in uvcg_video_enable
into its own separate function 'uvcg_video_disable'. This function
is now used anywhere uvcg_video_enable(video, 0) was used.
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Suggested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20231109004104.3467968-3-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the uvc gadget driver allocates all uvc_requests as one array
and deallocates them all when the video stream stops. This includes
de-allocating all the usb_requests associated with those uvc_requests.
This can lead to use-after-free issues if any of those de-allocated
usb_requests were still owned by the usb controller.
This patch is 1 of 2 patches addressing the use-after-free issue.
Instead of bulk allocating all uvc_requests as an array, this patch
allocates uvc_requests one at a time, which should allows for similar
granularity when deallocating the uvc_requests. This patch has no
functional changes other than allocating each uvc_request separately,
and similarly freeing each of them separately.
Link: https://lore.kernel.org/7cd81649-2795-45b6-8c10-b7df1055020d@google.com
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Suggested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20231109004104.3467968-2-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently the set_alt callback immediately disables the endpoint and queues
the v4l2 streamoff event. However, as the streamoff event is processed
asynchronously, it is possible that the video_pump thread attempts to queue
requests to an already disabled endpoint.
This change moves disabling usb endpoint to the end of streamoff event
callback. As the endpoint's state can no longer be used, video_pump is
now guarded by uvc->state as well. To be consistent with the actual
streaming state, uvc->state is now toggled between CONNECTED and STREAMING
from the v4l2 event callback only.
Link: https://lore.kernel.org/20230615171558.GK741@pendragon.ideasonboard.com/
Link: https://lore.kernel.org/20230531085544.253363-1-dan.scally@ideasonboard.com/
Reviewed-by: Daniel Scally <dan.scally@ideasonboard.com>
Reviewed-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Tested-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Avichal Rakesh <arakesh@google.com>
Link: https://lore.kernel.org/r/20231109004104.3467968-1-arakesh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch introduces a new USB quirk,
USB_QUIRK_SHORT_SET_ADDRESS_REQ_TIMEOUT, which modifies the timeout value
for the SET_ADDRESS request. The standard timeout for USB request/command
is 5000 ms, as recommended in the USB 3.2 specification (section 9.2.6.1).
However, certain scenarios, such as connecting devices through an APTIV
hub, can lead to timeout errors when the device enumerates as full speed
initially and later switches to high speed during chirp negotiation.
In such cases, USB analyzer logs reveal that the bus suspends for
5 seconds due to incorrect chirp parsing and resumes only after two
consecutive timeout errors trigger a hub driver reset.
Packet(54) Dir(?) Full Speed J(997.100 us) Idle( 2.850 us)
_______| Time Stamp(28 . 105 910 682)
_______|_____________________________________________________________Ch0
Packet(55) Dir(?) Full Speed J(997.118 us) Idle( 2.850 us)
_______| Time Stamp(28 . 106 910 632)
_______|_____________________________________________________________Ch0
Packet(56) Dir(?) Full Speed J(399.650 us) Idle(222.582 us)
_______| Time Stamp(28 . 107 910 600)
_______|_____________________________________________________________Ch0
Packet(57) Dir Chirp J( 23.955 ms) Idle(115.169 ms)
_______| Time Stamp(28 . 108 532 832)
_______|_____________________________________________________________Ch0
Packet(58) Dir(?) Full Speed J (Suspend)( 5.347 sec) Idle( 5.366 us)
_______| Time Stamp(28 . 247 657 600)
_______|_____________________________________________________________Ch0
This 5-second delay in device enumeration is undesirable, particularly
in automotive applications where quick enumeration is crucial
(ideally within 3 seconds).
The newly introduced quirks provide the flexibility to align with a
3-second time limit, as required in specific contexts like automotive
applications.
By reducing the SET_ADDRESS request timeout to 500 ms, the
system can respond more swiftly to errors, initiate rapid recovery, and
ensure efficient device enumeration. This change is vital for scenarios
where rapid smartphone enumeration and screen projection are essential.
To use the quirk, please write "vendor_id:product_id:p" to
/sys/bus/usb/drivers/hub/module/parameter/quirks
For example,
echo "0x2c48:0x0132:p" > /sys/bus/usb/drivers/hub/module/parameters/quirks"
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20231027152029.104363-2-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- The HCD address_device callback now accepts a user-defined timeout value
in milliseconds, providing better control over command execution times.
- The default timeout value for the address_device command has been set
to 5000 ms, aligning with the USB 3.2 specification. However, this
timeout can be adjusted as needed.
- The xhci_setup_device function has been updated to accept the timeout
value, allowing it to specify the maximum wait time for the command
operation to complete.
- The hub driver has also been updated to accommodate the newly added
timeout parameter during the SET_ADDRESS request.
Signed-off-by: Hardik Gajjar <hgajjar@de.adit-jv.com>
Reviewed-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Link: https://lore.kernel.org/r/20231027152029.104363-1-hgajjar@de.adit-jv.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The original Collison Avoidance mechanism, port->send_discover, avoids
the conflict when port partners start AMS almost the same time. However,
this mechanism is replaced by SINK_TX_OK and SINK_TX_NG. Skip the check
in PD3.0 to avoid the deadlock when source is requesting DR_SWAP where
sink is requesting DISCOVER_IDENTITY.
Signed-off-by: Guan-Yu Lin <guanyulin@google.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20231116083221.1201892-1-guanyulin@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Disable the vcc regulator on suspend and enable it on resume.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://lore.kernel.org/r/20231027122955.22123-1-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to free the "urs" platform device, which is created for some
ACPI platforms, on probe errors and on driver unbind.
Compile-tested only.
Fixes: c25c210f59 ("usb: dwc3: qcom: add URS Host support for sdm845 ACPI boot")
Cc: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Link: https://lore.kernel.org/r/20231117173650.21161-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to remove the software node also on (ACPI) probe errors to
avoid leaking the underlying resources.
Note that the software node is only used for ACPI probe so the driver
unbind tear down is updated to match probe.
Fixes: 8dc6e6dd1b ("usb: dwc3: qcom: Constify the software node")
Cc: stable@vger.kernel.org # 5.12
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231117173650.21161-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver needs to deregister and free the newly allocated dwc3 core
platform device on ACPI probe errors (e.g. probe deferral) and on driver
unbind but instead it leaked those resources while erroneously dropping
a reference to the parent platform device which is still in use.
For OF probing the driver takes a reference to the dwc3 core platform
device which has also always been leaked.
Fix the broken ACPI tear down and make sure to drop the dwc3 core
reference for both OF and ACPI.
Fixes: 8fd95da2cf ("usb: dwc3: qcom: Release the correct resources in dwc3_qcom_remove()")
Fixes: 2bc02355f8 ("usb: dwc3: qcom: Add support for booting with ACPI")
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Cc: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Cc: Lee Jones <lee@kernel.org>
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Acked-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231117173650.21161-2-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the IRQF_NO_AUTOEN irq flag when requesting the wakeup interrupts
instead of setting it separately.
No functional change intended.
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231120161607.7405-4-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Qualcomm glue driver is overriding the interrupt trigger types
defined by firmware when requesting the wakeup interrupts during probe.
This can lead to a failure to map the DP/DM wakeup interrupts after a
probe deferral as the firmware defined trigger types do not match the
type used for the initial mapping:
irq: type mismatch, failed to map hwirq-14 for interrupt-controller@b220000!
irq: type mismatch, failed to map hwirq-15 for interrupt-controller@b220000!
Fix this by not overriding the firmware provided trigger types when
requesting the wakeup interrupts.
Fixes: a4333c3a6b ("usb: dwc3: Add Qualcomm DWC3 glue driver")
Cc: stable@vger.kernel.org # 4.18
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Andrew Halaney <ahalaney@redhat.com>
Link: https://lore.kernel.org/r/20231120161607.7405-3-johan+linaro@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for the Microchip USB5744 USB3.0 and USB2.0 Hub.
The Microchip USB5744 supports two power supplies, one for 1V2 and one
for 3V3. According to the datasheet there is no need for a delay between
power on and reset, so this value is set to 0.
Signed-off-by: Stefan Eichenberger <stefan.eichenberger@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Cc: stable <stable@kernel.org>
Acked-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20231113145921.30104-3-francesco@dolcini.it
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Not all LJCA chips implement SPI and on chips without SPI reading
the SPI descriptors will timeout.
On laptop models like the Dell Latitude 9420, this is expected behavior
and not an error.
Modify the driver to continue without instantiating a SPI auxbus child,
instead of failing to probe() the whole LJCA chip.
Fixes: acd6199f19 ("usb: Add support for Intel LJCA device")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Wentong Wu <wentong.wu@intel.com>
Link: https://lore.kernel.org/r/20231104175104.38786-1-hdegoede@redhat.com
Link: https://lore.kernel.org/r/20231121203205.223047-1-hdegoede@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>