This HP Laptop uses ALC236 codec with COEF 0x07 controlling the
mute LED. Enable existing quirk for this device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240128155704.2333812-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If you connect an external headset/microphone to the 3.5mm jack on the
Acer Swift 1 SF114-32 it does not recognize the microphone. This fixes
that and gives the user the ability to choose between internal and
headset mic.
Signed-off-by: David Senoner <seda18@rolmail.net>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240126155626.2304465-1-seda18@rolmail.net
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Laptops 103C8C66, 103C8C67, 103C8C68, 103C8C6A use a dual speaker id
system where each speaker has its own speaker id.
The generic configuration table doesn't support this, so it needs its
own function.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240126164005.367021-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current method to set Channel Index when the system is missing _DSD
assumes that the channels alternate, which is not guaranteed.
Instead use the same methodology as the main driver does when _DSD
exists.
Fixes: 8c4c216db8 ("ALSA: hda: cs35l41: Add config table to support many laptops without _DSD")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240126164005.367021-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add quirks for two HP G11 laptops that use a Realtek HDA codec combined
with four CS35L56 amplifiers using SPI.
The CS35L56 driver uses the component binding interface, so uses the same
setup code as the CS35L41 quirks.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20240125123301.41692-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the generic parts of the hda_component implementation into a new
hda_component module. This will allow other HDA codecs to add support
for the component binding API without duplicating all the code.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Tested-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/20240124112607.77614-3-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Slightly re-work the code around cs35l41_generic_fixup() and the component
binding search so that it can be re-used for other amps that use the
component binding mechanism.
The match string is stored in struct scodec_dev_name instead of hardcoding
it in the match function.
The tas2781 does not use the amp index as part of the driver name match.
But its match format string does not include a field for the index, so
snprintf() would safely ignore the p->index argument. Because of this there
is no need for a special match function for this case, the CS35L41 code
can be re-used.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Tested-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/20240124112607.77614-2-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SSID 0x0c0d platform. It can't mute speaker when HP plugged.
This patch add quirk to fill speaker pin verbtable.
And disable speaker passthrough.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/38b82976a875451d833d514cee34ff6a@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Customer has reported an issue with specific desktop platform
where two CS42L42 codecs are connected to CS8409 HDA bridge.
If "Master Volume Control" is created then on Ubuntu OS UCM
left/right balance slider in UI audio settings has no effect.
This patch will fix this issue for a target paltform.
Fixes: 20e5077241 ("ALSA: hda/cs8409: Add support for dolphin")
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240122184710.5802-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Apollo Lake seems to also suffer from IRQ timing issues. After being up for ~4
minutes, a Pentium N4200 system ends up falling back to workqueue-based IRQ
handling:
[ 208.019906] snd_hda_intel 0000:00:0e.0: IRQ timing workaround is activated
for card #0. Suggest a bigger bdl_pos_adj.
Unfortunately, the Baytrail and Braswell workaround value of 32 samples isn't
enough to fix the issue here. Default to 64 samples.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240122114512.55808-3-rsalvaterra@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We have self-explanatory constants for Intel HDA devices, let's use them instead
of magic numbers and code comments.
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
Reviewed-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240122114512.55808-2-rsalvaterra@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP ZBook Power using ALC236 codec which using 0x02 to
control mute LED and 0x01 to control micmute LED.
Therefore, add a quirk to make it works.
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240122074826.1020964-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of small fixes:
- Lots of ASoC SOF fixes and related reworks
- ASoC TAS codec fixes including DT updates
- A few HD-audio quirks and regression fixes
- Minor fixes for aloop, oxygen and scarlett2 mixer
-----BEGIN PGP SIGNATURE-----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=h9S1
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes:
- Lots of ASoC SOF fixes and related reworks
- ASoC TAS codec fixes including DT updates
- A few HD-audio quirks and regression fixes
- Minor fixes for aloop, oxygen and scarlett2 mixer"
* tag 'sound-fix-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (23 commits)
ALSA: hda/realtek: Enable headset mic on Lenovo M70 Gen5
ALSA: hda/realtek: Enable mute/micmute LEDs and limit mic boost on HP ZBook
ALSA: hda/relatek: Enable Mute LED on HP Laptop 15s-fq2xxx
ASoC: SOF: ipc4-loader: remove the CPC check warnings
ASoC: SOF: ipc4-pcm: remove log message for LLP
ALSA: hda: generic: Remove obsolete call to ledtrig_audio_get
ALSA: scarlett2: Fix yet more -Wformat-truncation warnings
ALSA: hda: Properly setup HDMI stream
ASoC: audio-graph-card2: fix index check on graph_parse_node_multi_nm()
ASoC: SOF: icp3-dtrace: Revert "Fix wrong kfree() usage"
ALSA: oxygen: Fix right channel of capture volume mixer
ALSA: aloop: Introduce a function to get if access is interleaved mode
ASoC: mediatek: sof-common: Add NULL check for normal_link string
ASoC: mediatek: mt8195: Remove afe-dai component and rework codec link
ASoC: mediatek: mt8192: Check existence of dai_name before dereferencing
ASoC: Intel: bxt_rt298: Fix kernel ops due to COMP_DUMMY change
ASoC: Intel: bxt_da7219_max98357a: Fix kernel ops due to COMP_DUMMY change
ASoC: codecs: rtq9128: Fix TDM enable and DAI format control flow
ASoC: codecs: rtq9128: Fix PM_RUNTIME usage
ASoC: tas2781: Add tas2563 into driver
...
Lenovo M70 Gen5 is equipped with ALC623, and it needs
ALC283_FIXUP_HEADSET_MIC quirk to make its headset mic work.
Signed-off-by: Bin Li <bin.li@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240117154123.21578-1-bin.li@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some HP ZBooks, the audio LEDs can be enabled by
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF. So use it accordingly.
Signed-off-by: Yo-Jung Lin <leo.lin@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240116020722.27236-1-leo.lin@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This HP Laptop uses ALC236 codec with COEF 0x07 idx 1 controlling
the mute LED. This patch enables the already existing quirk for
this device.
Signed-off-by: Çağhan Demir <caghandemir@marun.edu.tr>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240115172303.4718-1-caghandemir@marun.edu.tr
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since 64f67b5240 ("leds: trigger: audio: Add an activate callback to
ensure the initial brightness is set") the audio triggers have an
activate callback which sets the LED brightness as soon as the
(default) trigger is bound to the LED device. So we can remove the
call to ledtrig_audio_get.
Positive side effect: We have no code dependency to ledtrig-audio any
longer, therefore, if built as module, it's no longer loaded if not
needed.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://lore.kernel.org/r/3dc9167d-fb33-43a6-baa6-dbef8b5da7b9@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It was a clam development cycle. There were an ALSA core extension
for subformat PCM bits and a few ASoC core changes to support N:M
mappings, while the most of remaining changes are driver-specific.
Core:
- API extensions for properly limiting PCM format bits via subformat
- Enhanced support for N:M CPU:CODEC mappings in the core and in
audio-graph-card2
ASoC:
- Lots of SOF updates: fallback support to older IPC versions,
notification on control changes with IPC4.
Also supports for ACPI parse for the ES83xx driver that reduces
quirks.
- Device tree support for describing parts of the card which can be
active over suspend (for very low power playback or wake word use
cases)
- Support for more AMD and Intel systems, NXP i.MX8m MICFIL, Qualcomm
SM8250, SM8550, SM8650 and X1E80100
- Drop of Freescale MPC8610 code that is no longer supported
HD-audio:
- More CS35L41 codec extensions for Dell, HP and Lenovo models
- TAS2781 codec extensions for Lenovo and co
- New PCM subformat supports
Others:
- More enhancement for Scarlett2 USB mixer support
- Various kselftest fixes
-----BEGIN PGP SIGNATURE-----
iQJCBAABCAAsFiEEIXTw5fNLNI7mMiVaLtJE4w1nLE8FAmWfzJgOHHRpd2FpQHN1
c2UuZGUACgkQLtJE4w1nLE/NHg//VT0JRZDKqAZMUIaFZswUIKgoUy9fY9WaePO+
db38uFzjuTC1ZN1PIDFnU0bQ2uL7IYF/xnceqitk+G76+Wt/pcDP/1hX+F9UhsVd
wgRrihBeNRtSmPku8cwKu+duD/46439JyWo34PdHm8FxNoyilBx6fIApk6JqB57V
HYU3ZFtQE84s8TmPHefasLeewY5thFtWYXLAaEZR5oohyXUTN0Np7h7vG8nchh1F
zZOwoQ+nBo607PwUoXd0BFYkcuXwHlK4vLVmAM05KPaH1Q/kesEecYMhIVbnDHOj
a4caMz+/tMbNbw3/GRsg8HgIeiyp1NoyC4LAqufa+Pj6BgPREVra5j8XoxAnCxXr
8X8EDtBds6frMzqtQyNvTkyRCf3Iki8fhz60Re5nEkoXLcv34E3kleQDLG/FnHqC
qeH0J3FEed84Gf6KrnpjkPHLFRx5ZKyahOHZ7Xc76fUYMCwvczkc5CKeG2EoivE4
koEkhlQU1gnNyjNTTi4JchWis+EZG/oNA91eud1lMDm320lFJmxdZ5z31xZubVvs
WTcMStgHCDPIKOeSBuwBCYFwugMtV/o/ejE567E4bxVC5ZA/zbxyvpxU9iDAjUNK
T0JdPf/KKy1YJiNe9xuJn9/1ZpV6BXFCl7b7wILV+ZbGduOczoMCEH5T7dwAmZqq
/lQtT/8=
=yVxc
-----END PGP SIGNATURE-----
Merge tag 'sound-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"It was a calm development cycle. There were an ALSA core extension for
subformat PCM bits and a few ASoC core changes to support N:M
mappings, while the most of remaining changes are driver-specific.
Core:
- API extensions for properly limiting PCM format bits via subformat
- Enhanced support for N:M CPU:CODEC mappings in the core and in
audio-graph-card2
ASoC:
- Lots of SOF updates: fallback support to older IPC versions,
notification on control changes with IPC4. Also supports for ACPI
parse for the ES83xx driver that reduces quirks.
- Device tree support for describing parts of the card which can be
active over suspend (for very low power playback or wake word use
cases)
- Support for more AMD and Intel systems, NXP i.MX8m MICFIL, Qualcomm
SM8250, SM8550, SM8650 and X1E80100
- Drop of Freescale MPC8610 code that is no longer supported
HD-audio:
- More CS35L41 codec extensions for Dell, HP and Lenovo models
- TAS2781 codec extensions for Lenovo and co
- New PCM subformat supports
Others:
- More enhancement for Scarlett2 USB mixer support
- Various kselftest fixes"
* tag 'sound-6.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (337 commits)
kselftest/alsa - conf: Stringify the printed errno in sysfs_get()
kselftest/alsa - mixer-test: Fix the print format specifier warning
kselftest/alsa - mixer-test: Fix the print format specifier warning
kselftest/alsa - mixer-test: fix the number of parameters to ksft_exit_fail_msg()
ALSA: hda/tas2781: annotate calibration data endianness
ALSA: hda/realtek: Fix mute and mic-mute LEDs for HP Envy X360 13-ay0xxx
ALSA: hda/conexant: Fix headset auto detect fail in cx8070 and SN6140
ALSA: ac97: fix build regression
ALSA: hda: cs35l41: Support more HP models without _DSD
ALSA: hda/tas2781: add fixup for Lenovo 14ARB7
ALSA: hda/tas2781: add TAS2563 support for 14ARB7
ALSA: hda/tas2781: add configurable global i2c address
ALSA: hda/tas2781: add ptrs to calibration functions
ALSA: hda: Add driver properties for cs35l41 for Lenovo Legion Slim 7 Gen 8 serie
ALSA: hda/realtek: enable SND_PCI_QUIRK for Lenovo Legion Slim 7 Gen 8 (2023) serie
ALSA: hda/tas2781: configure the amp after firmware load
ALSA: mark all struct bus_type as const
ASoC: pxa: sspa: Don't select SND_ARM
ASoC: rt5663: cancel the work when system suspends
ALSA: scarlett2: Add PCM Input Switch for Solo Gen 4
...
Since commit 4005d1ba0a ("ASoC: soc-dai: don't call PCM audio ops if
the stream is not supported") HDMI playback is broken with avs driver.
This happens because for HDMI stream (unlike generic HDA one)
channels_min for stream is not set when creating PCMs. Fix this by
setting the value based on first available converter.
Fixes: 4005d1ba0a ("ASoC: soc-dai: don't call PCM audio ops if the stream is not supported")
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20240112113349.2905328-1-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A moderately busy release for SPI, the main core update was the merging
of support for multiple chip selects, used in some flash configurations.
There were also big overhauls for the AXI SPI Engine and PL022 drivers,
plus some new device support for ST.
There's a few patches for other trees, API updates to allow the
multiple chip select support and one of the naming modernisations
touched a controller embedded in the USB code.
- Support for multiple chip selects.
- A big overhaul for the AXI SPI engine driver, modernising it and
adding a bunch of new features.
- Modernisation of the PL022 driver, fixing some issues with submitting
messages while in atomic context in the process.
- Many drivers were converted to use new APIs which avoid outdated
terminology for devices and controllers.
- Support for ST Microelectronics STM32F7 and STM32MP25, and Renesas
RZ/Five.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmWbHmMACgkQJNaLcl1U
h9CpSwf+O981469g1twyEpq5PJlNgdXmrKUpezcC18X4DLXmlf5hoCsHUFIU2DuX
oBZuUQVp1KaEzJ4LX1giAOTuhfwPAItGR+/JMs6VxT/V0MMCHaNYcU5zLHXacDFL
URU7hyyhxUp9PzGNI/IEQH2DPv3QVX8Z1CVQQNQpnTsvbpBEF/osxB3SdWg65Y4J
B9nEW5hnyDsjxQVzjwCMFsy1vJeaBkP++zdPhPGE4RaNcweX+hksVRWVJ3DqUuJC
u4IyO5Hmduqmyjyc7MEV6lekecnyHc72WIzFXJpy0FOW0CstOQD59D5Fnbdvbb9i
mm3IJ1Vh/oepZBNPAmHCPqMEAqr5ZQ==
=49Kh
-----END PGP SIGNATURE-----
Merge tag 'spi-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A moderately busy release for SPI, the main core update was the
merging of support for multiple chip selects, used in some flash
configurations. There were also big overhauls for the AXI SPI Engine
and PL022 drivers, plus some new device support for ST.
There's a few patches for other trees, API updates to allow the
multiple chip select support and one of the naming modernisations
touched a controller embedded in the USB code.
- Support for multiple chip selects.
- A big overhaul for the AXI SPI engine driver, modernising it and
adding a bunch of new features.
- Modernisation of the PL022 driver, fixing some issues with
submitting messages while in atomic context in the process.
- Many drivers were converted to use new APIs which avoid outdated
terminology for devices and controllers.
- Support for ST Microelectronics STM32F7 and STM32MP25, and Renesas
RZ/Five"
* tag 'spi-v6.8' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (83 commits)
spi: stm32: add st,stm32mp25-spi compatible supporting STM32MP25 soc
dt-bindings: spi: stm32: add st,stm32mp25-spi compatible
spi: stm32: use dma_get_slave_caps prior to configuring dma channel
spi: axi-spi-engine: fix struct member doc warnings
spi: pl022: update description of internal_cs_control()
spi: pl022: delete description of cur_msg
spi: dw: Remove Intel Thunder Bay SOC support
spi: dw: Remove Intel Thunder Bay SOC support
spi: sh-msiof: Enforce fixed DTDL for R-Car H3
spi: ljca: switch to use devm_spi_alloc_host()
spi: cs42l43: switch to use devm_spi_alloc_host()
spi: zynqmp-gqspi: switch to use modern name
spi: zynq-qspi: switch to use modern name
spi: xtensa-xtfpga: switch to use modern name
spi: xlp: switch to use modern name
spi: xilinx: switch to use modern name
spi: xcomm: switch to use modern name
spi: uniphier: switch to use modern name
spi: topcliff-pch: switch to use modern name
spi: wpcm-fiu: switch to use devm_spi_alloc_host()
...
When OMTP headset plugin the headset jack of CX8070 and SN6160 sound cards,
the headset type detection circuit will recognize the headset type as CTIA.
At this point, plugout and plugin the headset will get the correct headset
type as OMTP.
The reason for the failure of headset type recognition is that the sound
card creation will enable the VREF voltage of the headset mic, which
interferes with the headset type automatic detection circuit. Plugout and
plugin the headset will restart the headset detection and get the correct
headset type.
The patch is disable the VREF voltage when the headset is not present, and
will enable the VREF voltage when the headset is present.
Signed-off-by: bo liu <bo.liu@senarytech.com>
Link: https://lore.kernel.org/r/20240108110235.3867-1-bo.liu@senarytech.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_SPI is disabled, the driver produces unused-variable warning:
sound/pci/hda/cs35l41_hda_property.c: In function 'generic_dsd_config':
sound/pci/hda/cs35l41_hda_property.c:181:28: error: unused variable 'spi' [-Werror=unused-variable]
181 | struct spi_device *spi;
| ^~~
sound/pci/hda/cs35l41_hda_property.c:180:27: error: unused variable 'cs_gpiod' [-Werror=unused-variable]
180 | struct gpio_desc *cs_gpiod;
| ^~~~~~~~
Avoid these by turning the preprocessor contionals into equivalent C code,
which also helps readability.
Fixes: 916d051730 ("ALSA: hda: cs35l41: Only add SPI CS GPIO if SPI is enabled in kernel")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20240103102606.3742476-1-arnd@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This adds overrides for a series of notebooks using a common config
taken from HP's proprietary Windows driver.
This has been tested on a HP 15-ey0xxxx device (subsystem 103C8A31)
together with another Realtek quirk and the calibration files from the
proprietary driver.
Signed-off-by: Lorenz Brun <lorenz@brun.one>
Cc: <stable@vger.kernel.org> # v6.7
Link: https://lore.kernel.org/r/20240102214821.3394810-1-lorenz@brun.one
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is a HP ZBook which using ALC236 codec and need the
ALC236_FIXUP_HP_MUTE_LED_MICMUTE_VREF quirk to make mute LED
and micmute LED work.
[ confirmed that the new entries are for new models that have no
proper name, so the strings are left as "HP" which will be updated
eventually later -- tiwai ]
Signed-off-by: Andy Chi <andy.chi@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20240102024916.19093-1-andy.chi@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add driver properties on 4 models of this laptop serie since they don't
have _DSD in the ACPI table
Signed-off-by: Dorian Cruveiller <doriancruveiller@gmail.com>
Cc: <stable@vger.kernel.org> # v6.7
Link: https://lore.kernel.org/r/20231230114312.22118-1-doriancruveiller@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Pavilion 14 ec1xxx series uses the HP mainboard 8A0F with the
ALC287 codec.
The mute led can be enabled using the already existing
ALC287_FIXUP_HP_GPIO_LED quirk.
Tested on an HP Pavilion ec1003AU
Signed-off-by: Aabish Malik <aabishmalik3337@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231229170352.742261-3-aabishmalik3337@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2 or 4 CS35L41 amps with HDA using SPI and I2C.
Models use internal and external boost.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org> # v6.7+
Link: https://lore.kernel.org/r/20231221132518.3213-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some laptops without _DSD have the SPI speed set very low in the BIOS.
Since the SPI controller uses this speed as its max speed, the SPI
transactions are very slow. Firmware download writes to many registers,
and if the SPI speed is too slow, it can take a long time to download.
For this reason, disable firmware loading if the maximum SPI speed is
too low. Without Firmware, audio playback will work, but the volume
will be low to ensure safe operation of the CS35L41.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org> # v6.7+
Link: https://lore.kernel.org/r/20231221132518.3213-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are two problems with using regcache in this module.
The amplifier has 3 addressing levels (BOOK, PAGE, REG). The firmware
contains blocks that must be written to BOOK 0x8C. The regcache doesn't
know anything about BOOK, so regcache_sync writes invalid values to the
actual BOOK.
The module handles 2 or more separate amplifiers. The amplifiers have
different register values, and the module uses only one regmap/regcache
for all the amplifiers. The regcache_sync only writes the last amplifier
used.
The module successfully restores all the written register values (RC
profile, program, configuration, calibration) without regcache.
Remove regcache functions and set regmap cache_type to REGCACHE_NONE.
Link: https://lore.kernel.org/r/21a183b5a08cb23b193af78d4b1114cc59419272.1701906455.git.soyer@irl.hu/
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Acked-by: Mark Brown <broonie@kernel.org>
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/491aeed0e2eecc3b704ec856f815db21bad3ba0e.1703202126.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Initialise the variables to NULL so that they cannot be uninitialised
when devm_kfree is called.
Found by static analysis.
Fixes: 8c4c216db8 ("ALSA: hda: cs35l41: Add config table to support many laptops without _DSD")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231219162232.790358-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2xCS35L41amps with HDA using SPI and I2C.
Models use internal and external boost.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-8-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2xCS35L41amps with HDA using SPI and I2C.
Models use internal and external boost.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-6-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These models use 2xCS35L41amps with HDA using SPI and I2C.
All models use Internal Boost.
Some models also use Realtek Speakers in conjunction with
CS35L41.
All models require DSD support to be added inside
cs35l41_hda_property.c
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This make use of the CS35L41 HDA Property framework, which supports
laptops which do not have the _DSD properties in their ACPI.
Add configuration table to be able to use a generic function which allows
laptops to be supported just by adding an entry into the table.
Use configuration table function for existing system 103C89C6.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231218151221.388745-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, cur_prog/cur_conf remains at the default value (-1), while
program 0 has been loaded into the amplifiers.
In the playback hook, tasdevice_tuning_switch tries to restore the
cur_prog/cur_conf. In the runtime_resume/system_resume,
tasdevice_prmg_load tries to load the cur_prog as well.
Set cur_prog and cur_conf to 0 if available in the firmware.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/038add0bdca1f979cc7abcce8f24cbcd3544084b.1702596646.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Calling component_add starts loading the firmware, the callback function
writes the program to the amplifiers. If the module resets the
amplifiers after component_add, it happens that one of the amplifiers
does not work because the reset and program writing are interleaving.
Call tas2781_reset before component_add to ensure reliable
initialization.
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/4d23bf58558e23ee8097de01f70f1eb8d9de2d15.1702511246.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If the module can load the RCA but not the firmware binary, it will call
the cleanup functions. Then unloading the module causes general
protection fault due to double free.
Do not call the cleanup functions in tasdev_fw_ready.
general protection fault, probably for non-canonical address
0x6f2b8a2bff4c8fec: 0000 [#1] PREEMPT SMP NOPTI
Call Trace:
<TASK>
? die_addr+0x36/0x90
? exc_general_protection+0x1c5/0x430
? asm_exc_general_protection+0x26/0x30
? tasdevice_config_info_remove+0x6d/0xd0 [snd_soc_tas2781_fmwlib]
tas2781_hda_unbind+0xaa/0x100 [snd_hda_scodec_tas2781_i2c]
component_unbind+0x2e/0x50
component_unbind_all+0x92/0xa0
component_del+0xa8/0x140
tas2781_hda_remove.isra.0+0x32/0x60 [snd_hda_scodec_tas2781_i2c]
i2c_device_remove+0x26/0xb0
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/1a0885c424bb21172702d254655882b59ef6477a.1702510018.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The code does not properly check whether the calibration variable is
available in the EFI. If it is not available, it causes a NULL pointer
dereference.
Check the return value of the first get_variable call also.
BUG: kernel NULL pointer dereference, address: 0000000000000000
Call Trace:
<TASK>
? __die+0x23/0x70
? page_fault_oops+0x171/0x4e0
? srso_alias_return_thunk+0x5/0x7f
? schedule+0x5e/0xd0
? exc_page_fault+0x7f/0x180
? asm_exc_page_fault+0x26/0x30
? crc32_body+0x2c/0x120
? tas2781_save_calibration+0xe4/0x220 [snd_hda_scodec_tas2781_i2c]
tasdev_fw_ready+0x1af/0x280 [snd_hda_scodec_tas2781_i2c]
request_firmware_work_func+0x59/0xa0
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
CC: stable@vger.kernel.org
Signed-off-by: Gergo Koteles <soyer@irl.hu>
Link: https://lore.kernel.org/r/f1f6583bda918f78556f67d522ca7b3b91cebbd5.1702251102.git.soyer@irl.hu
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP laptop 15-db0403ng uses the ALC236 codec and controls the mute
LED using COEF 0x07 index 1.
Sound card subsystem: Hewlett-Packard Company Device [103c:84ae]
Use the existing quirk for this model.
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/e61815d0-f1c7-b164-e49d-6ca84771476a@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On ASUSTeK Z170M PLUS and Z170 PRO GAMING systems, the display codec
pins are not registered properly without the force-connect quirk. The
codec will report only one pin as having external connectivity, but i915
finds all three connectors on the system, so the two drivers are not
in sync.
Issue found with DRM igt-gpu-tools test kms_hdmi_inject@inject-audio.
Link: https://gitlab.freedesktop.org/drm/intel/-/issues/9801
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231208132127.2438067-3-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add one more older NUC model that requires quirk to force all pins to be
connected. The display codec pins are not registered properly without
the force-connect quirk. The codec will report only one pin as having
external connectivity, but i915 finds all three connectors on the
system, so the two drivers are not in sync.
Issue found with DRM igt-gpu-tools test kms_hdmi_inject@inject-audio.
Link: https://gitlab.freedesktop.org/drm/igt-gpu-tools/-/issues/3
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Jani Saarinen <jani.saarinen@intel.com>
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231208132127.2438067-2-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge series from Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>:
This patch series adds support to the SPI framework for using multiple
chip selects.
In preparation for adding multiple CS support for a device, set/get
functions were introduces accessing spi->chip_select in
'commit 303feb3cc0 ("spi: Add APIs in spi core to set/get
spi->chip_select and spi->cs_gpiod")'.
Replace spi->chip_select with spi_get_chipselect() API.
Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
Link: https://lore.kernel.org/r/20231125092137.2948-3-amit.kumar-mahapatra@amd.com
Signed-off-by: Mark Brown <broonie@kernel.org>
The Framework 16" laptop has the same controller as other Framework
models. Apply the presence detection quirk.
Signed-off-by: Mario Limonciello <mario.limonciello@amd.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231206193927.2996-1-mario.limonciello@amd.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Framework Laptop 13 (AMD Ryzen 7040Series) has an ALC295 with
a disconnected or faulty headset mic presence detect similar to the
previous models. It works with the same quirk chain as
309d7363ca. This model has a VID:PID
of f111:0006.
Signed-off-by: Tim Bosse <flinn@timbos.se>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231206142629.388615-1-flinn@timbos.se
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo M90 Gen5 is equipped with ALC897, and it needs
ALC897_FIXUP_HEADSET_MIC_PIN quirk to make its headset mic work.
Signed-off-by: Bin Li <bin.li@canonical.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231204100450.642783-1-bin.li@canonical.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
XPS 9530 has 2 tweeters and 2 subwoofers powered by CS35L41 amplifier, SPI
connected. For subwoofers to work, it requires both to enable amplifier
support, and to enable output to subwoofers via 0x17 quirk (similalry to
XPS 9510/9520).
Signed-off-by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231203233006.100558-1-alex.vinarskis@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ASUS UM3504DA uses a Realtek HDA codec and two CS35L41 amplifiers via I2C.
Apply existing quirk to model.
Signed-off-by: Pascal Noël <pascal@pascalcompiles.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231202013744.12369-1-pascal@pascalcompiles.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's been reported that the runtime PM on KONTRON SinglePC (PCI SSID
1734:1232) caused a stall of playback after a bunch of invocations.
(FWIW, this looks like an timing issue, and the stall happens rather
on the controller side.)
As a workaround, disable the default power-save on this platform.
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231130151321.9813-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To provide option for selecting different bit-per-sample than just the
maximum one, use the new format calculation mechanism.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20231117120610.1755254-8-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To provide option for selecting different bit-per-sample than just the
maximum one, use the new format calculation mechanism.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20231117120610.1755254-7-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To provide option for selecting different bit-per-sample than just the
maximum one, use the new format calculation mechanism.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Link: https://lore.kernel.org/r/20231117120610.1755254-6-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Update mechanism for querying supported PCMs to allow for granular
format selection when container size is 32 bits. Currently always the
highest bit depth is selected, regardless of how many actual formats
codec in question supports.
Acked-by: Mark Brown <broonie@kernel.org>
Co-developed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20231117120610.1755254-3-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SPI hibernation is now supported with the latest hibernation/wake
sequences in the shared ASoC code.
This has a functional dependency on two commits:
commit 3df761bdbc ("ASoC: cs35l56: Wake transactions need to be issued
twice")
commit a47cf4dac7 ("ASoC: cs35l56: Change hibernate sequence to use
allow auto hibernate")
To protect against this, enabling hibernation is conditional on
CS35L56_WAKE_HOLD_TIME_US being defined, which indicates that the new
hibernation sequences are available.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231121154419.19435-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some older laptops using cs35l41 use firmware which does not support
the CSPL_MBOX_CMD_SPK_OUT_ENABLE command.
Firmware versions v0.28.0 and older do not support this command.
Fixes: fa3efcc36a ("ALSA: cs35l41: Use mbox command to enable speaker output for external boost")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231117163609.823627-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This state duplicates the running state inside cs_dsp, so is not necessary.
Remove it, and use cs_dsp.running instead.
This brings the CS35L41 HDA driver more inline with its ASoC version,
allowing the same state to be used when calling library functions.
Fixes: fa3efcc36a ("ALSA: cs35l41: Use mbox command to enable speaker output for external boost")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231117163609.823627-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of small fixes: including a regression fix in RC1
wrt HD-audio / i915 component binding, while the rest are HD-audio
device-speific fixes / quirks.
-----BEGIN PGP SIGNATURE-----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=JybD
-----END PGP SIGNATURE-----
Merge tag 'sound-6.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of small fixes: including a regression fix in RC1 wrt
HD-audio / i915 component binding, while the rest are HD-audio
device-speific fixes / quirks"
* tag 'sound-6.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek: Add quirks for HP Laptops
ALSA: hda/realtek: Add quirks for ASUS 2024 Zenbooks
ALSA: hda: i915: Alays handle -EPROBE_DEFER
ALSA: hda/realtek: Enable Mute LED on HP 255 G10
ALSA: hda: cs35l56: Enable low-power hibernation mode on i2c
ALSA: hda/realtek - Enable internal speaker of ASUS K6500ZC
ALSA: hda/realtek: Enable Mute LED on HP 255 G8
ALSA: hda/realtek - Add Dell ALC295 to pin fall back table
These HP laptops use Realtek HDA codec combined with 2 or 4 CS35L41
Amplifiers using SPI with Internal Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231115162116.494968-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These ASUS Zenbook laptops use Realtek HDA codec combined with
2xCS35L41 Amplifiers using SPI or I2C with External Boost or
Internal Boost.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231115162116.494968-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HP 255 G10 has a mute LED that can be made to work using quirk
ALC236_FIXUP_HP_MUTE_LED_COEFBIT2.
Enable already existing quirk - at correct line to keep order
Signed-off-by: Matus Malych <matus@malych.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231114133524.11340-1-matus@malych.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This can now be re-enabled as the sequence to reliably wake the device
has been implemented in the shared ASoC code.
This has a functional dependency on commit 3df761bdbc
("ASoC: cs35l56: Wake transactions need to be issued twice")
To protect against this, enabling hibernation is conditional on
CS35L56_WAKE_HOLD_TIME_US being defined, which indicates that the new
hibernation sequences are available.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231113164029.1156669-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A collection of fixes for RC1. Majority of changes are various
ASoC driver-specific small fixes and usual HD-audio quirks, while
there are a couple of core changes: a fix in ALSA core procfs code
to avoid deadlocks at disconnection and an ASoC core fix for DAPM
clock widgets.
-----BEGIN PGP SIGNATURE-----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=6iW2
-----END PGP SIGNATURE-----
Merge tag 'sound-fix-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of fixes for rc1.
The majority of changes are various ASoC driver-specific small fixes
and usual HD-audio quirks, while there are a couple of core changes: a
fix in ALSA core procfs code to avoid deadlocks at disconnection and
an ASoC core fix for DAPM clock widgets"
* tag 'sound-fix-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
OSS: dmasound/paula: Convert to platform remove callback returning void
ALSA: hda: ASUS UM5302LA: Added quirks for cs35L41/10431A83 on i2c bus
ALSA: info: Fix potential deadlock at disconnection
ASoC: nau8540: Add self recovery to improve capture quility
ALSA: hda/realtek: Add support dual speaker for Dell
ALSA: hda: Add ASRock X670E Taichi to denylist
ALSA: hda/realtek: Add quirk for ASUS UX7602ZM
ASoC: SOF: sof-client: trivial: fix comment typo
ASoC: dapm: fix clock get name
ASoC: hdmi-codec: register hpd callback on component probe
ASoC: mediatek: mt8186_mt6366_rt1019_rt5682s: trivial: fix error messages
ASoC: da7219: Improve system suspend and resume handling
ASoC: codecs: Modify macro value error
ASoC: codecs: Modify the wrong judgment of re value
ASoC: codecs: Modify the maximum value of calib
ASoC: amd: acp: fix for i2s mode register field update
ASoC: codecs: aw88399: Fix -Wuninitialized in aw_dev_set_vcalb()
ASoC: rt712-sdca: fix speaker route missing issue
ASoC: rockchip: Fix unused rockchip_i2s_tdm_match warning for !CONFIG_OF
ASoC: ti: omap-mcbsp: Fix runtime PM underflow warnings
Add ALC295 to pin fall back table.
Remove 5 pin quirks for Dell ALC295.
ALC295 was only support MIC2 for external MIC function.
ALC295 assigned model "ALC269_FIXUP_DELL1_MIC_NO_PRESENCE" for pin
fall back table.
It was assigned wrong model. So, let's remove it.
Fixes: fbc571290d ("ALSA: hda/realtek - Fixed Headphone Mic can't record on Dell platform")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/7c1998e873834df98d59bd7e0d08c72e@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Proposed patch fixes initialization of CSC3551 on the UM5302LA laptop.
Patching DSDT table is not required since ASUS did added _DSD entry.
Nothing new introduced but reused work started by Stefan B.
Currently there is no official firmware available for 10431A83 on
cirrus git unfortunately.
For testing used 104317f3 (which is also seems on i2c bus):
$ cd /lib/firmware/cirrus/ && \
for fw in $(find ./ -name '*104317f3*'); do newfw=$(echo $fw | sed 's/104317f3/10431a83/g'); echo echo "$fw -> $newfw"; ln -s $f $newfw; done
With the patch applied to 6.6.0 and obviously symlinks to 104317F3 FW,
speakers works and to my susrprise they sound quite good and loud
without distortion.
Probably confirmation from cirrus team is needed on firmware.
Signed-off-by: Vitalii Torshyn <vitaly.torshyn@gmail.com>
Link: https://bugzilla.kernel.org/show_bug.cgi?id=218119
Link: https://lore.kernel.org/r/CAHiQ-bCMPpCJ8eOYAaVVoqGkFixS1qTgSS4xfbZvL4oZV9LYew@mail.gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Dell new platform support dual speaker. But BIOS verb table only show one speaker.
It will fill verb table for second speaker. Then bind with CS AMP model.
Fixes: de90f5165b ("ALSA: hda/realtek: Add support for DELL Oasis 13/14/16 laptops")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/4dd390a77bf742b8a518ac2deee00b0f@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recent AMD platforms expose an HD-audio bus but without any actual
codecs, which is internally tied with a USB-audio device, supposedly.
It results in "no codecs" error of HD-audio bus driver, and it's
nothing but a waste of resources.
snd_hda_intel 0000:59:00.6: no codecs found!
Signed-off-by: Alexander Koskovich <akoskovich@pm.me>
Link: https://lore.kernel.org/r/20231105152834.5620-1-akoskovich@pm.me
Signed-off-by: Takashi Iwai <tiwai@suse.de>
there's little I can say which isn't in the individual changelogs.
The lengthier patch series are
- "kdump: use generic functions to simplify crashkernel reservation in
arch", from Baoquan He. This is mainly cleanups and consolidation of
the "crashkernel=" kernel parameter handling.
- After much discussion, David Laight's "minmax: Relax type checks in
min() and max()" is here. Hopefully reduces some typecasting and the
use of min_t() and max_t().
- A group of patches from Oleg Nesterov which clean up and slightly fix
our handling of reads from /proc/PID/task/... and which remove
task_struct.therad_group.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQTTMBEPP41GrTpTJgfdBJ7gKXxAjgUCZUQP9wAKCRDdBJ7gKXxA
jmOAAQDh8sxagQYocoVsSm28ICqXFeaY9Co1jzBIDdNesAvYVwD/c2DHRqJHEiS4
63BNcG3+hM9nwGJHb5lyh5m79nBMRg0=
=On4u
-----END PGP SIGNATURE-----
Merge tag 'mm-nonmm-stable-2023-11-02-14-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull non-MM updates from Andrew Morton:
"As usual, lots of singleton and doubleton patches all over the tree
and there's little I can say which isn't in the individual changelogs.
The lengthier patch series are
- 'kdump: use generic functions to simplify crashkernel reservation
in arch', from Baoquan He. This is mainly cleanups and
consolidation of the 'crashkernel=' kernel parameter handling
- After much discussion, David Laight's 'minmax: Relax type checks in
min() and max()' is here. Hopefully reduces some typecasting and
the use of min_t() and max_t()
- A group of patches from Oleg Nesterov which clean up and slightly
fix our handling of reads from /proc/PID/task/... and which remove
task_struct.thread_group"
* tag 'mm-nonmm-stable-2023-11-02-14-08' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (64 commits)
scripts/gdb/vmalloc: disable on no-MMU
scripts/gdb: fix usage of MOD_TEXT not defined when CONFIG_MODULES=n
.mailmap: add address mapping for Tomeu Vizoso
mailmap: update email address for Claudiu Beznea
tools/testing/selftests/mm/run_vmtests.sh: lower the ptrace permissions
.mailmap: map Benjamin Poirier's address
scripts/gdb: add lx_current support for riscv
ocfs2: fix a spelling typo in comment
proc: test ProtectionKey in proc-empty-vm test
proc: fix proc-empty-vm test with vsyscall
fs/proc/base.c: remove unneeded semicolon
do_io_accounting: use sig->stats_lock
do_io_accounting: use __for_each_thread()
ocfs2: replace BUG_ON() at ocfs2_num_free_extents() with ocfs2_error()
ocfs2: fix a typo in a comment
scripts/show_delta: add __main__ judgement before main code
treewide: mark stuff as __ro_after_init
fs: ocfs2: check status values
proc: test /proc/${pid}/statm
compiler.h: move __is_constexpr() to compiler.h
...
Most of changes at this time are for ASoC, spread over ASoC core and
drivers due to the API prefix standardization. Other than that, there
have little change wrt API, rather lots of driver-specific updates and
fixes. Some highlight below:
ASoC:
- Standardization of API prefix
- GPIO API usage improvements
- Support for HDA patches
- Lots of work on SOF, including crash dump support
- Fixes for noise when stopping some Sounwire CODECs
- Support for AMD platforms with es83xx, AMD ACP 6.3 and 7.0, Awinc
AT87390 and AW88399, many Intel platforms, many Mediatek platforms,
Qualcomm SM6115 and SC7180 platforms, Richtek RTQ9128 and Texas
Instruments TAS575x
HD-audio and USB-audio:
- Deferred probe support of audio component binding
- More fixes and enhancements for Cirrus subcodecs
- USB Scarlett2 mixer and McIntosh DSD quirk
Others:
- More enhancement of snd-aloop driver
- Update MAINTAINERS entry for linux-sound mailing list
-----BEGIN PGP SIGNATURE-----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=2/dI
-----END PGP SIGNATURE-----
Merge tag 'sound-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"Most of changes at this time are for ASoC, spread over ASoC core and
drivers due to the API prefix standardization.
Other than that, there have little change wrt API, rather lots of
driver-specific updates and fixes.
Some highlight below:
ASoC:
- Standardization of API prefix
- GPIO API usage improvements
- Support for HDA patches
- Lots of work on SOF, including crash dump support
- Fixes for noise when stopping some Sounwire CODECs
- Support for AMD platforms with es83xx, AMD ACP 6.3 and 7.0, Awinc
AT87390 and AW88399, many Intel platforms, many Mediatek platforms,
Qualcomm SM6115 and SC7180 platforms, Richtek RTQ9128 and Texas
Instruments TAS575x
HD-audio and USB-audio:
- Deferred probe support of audio component binding
- More fixes and enhancements for Cirrus subcodecs
- USB Scarlett2 mixer and McIntosh DSD quirk
Others:
- More enhancement of snd-aloop driver
- Update MAINTAINERS entry for linux-sound mailing list"
* tag 'sound-6.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (485 commits)
ALSA: hda: cs35l41: Fix missing error code in cs35l41_smart_amp()
ALSA: hda: cs35l41: mark cs35l41_verify_id() static
ASoC: codecs: wsa883x: make use of new mute_unmute_on_trigger flag
ASoC: soc-dai: add flag to mute and unmute stream during trigger
ASoC: ams-delta.c: use component after check
ASoC: amd: acp: select SND_SOC_AMD_ACP_LEGACY_COMMON for ACP63
ASoC: codecs: aw88399: fix typo in Kconfig select
ASoC: amd: acp: add ACPI dependency
ASoC: Intel: avs: Add rt5514 machine board
ASoC: Intel: avs: Add rt5514 machine board
ALSA: scarlett2: Add missing check with firmware version control
ALSA: virtio: use ack callback
ALSA: scarlett2: Remap Level Meter values
ALSA: scarlett2: Allow passing any output to line_out_remap()
ALSA: scarlett2: Add support for reading firmware version
ALSA: scarlett2: Rename Gen 3 config sets
ALSA: scarlett2: Rename scarlett_gen2 to scarlett2
ASoC: cs35l41: Detect CSPL errors when sending CSPL commands
ALSA: hda: cs35l41: Check CSPL state after loading firmware
ALSA: hda: cs35l41: Do not unload firmware before reset in system suspend
...
-----BEGIN PGP SIGNATURE-----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=G//C
-----END PGP SIGNATURE-----
Merge tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Use acpi_evaluate_dsm_typed() instead of open-coding _DSM
evaluation to learn device characteristics (Andy Shevchenko)
- Tidy multi-function header checks using new PCI_HEADER_TYPE_MASK
definition (Ilpo Järvinen)
- Simplify config access error checking in various drivers (Ilpo
Järvinen)
- Use pcie_capability_clear_word() (not
pcie_capability_clear_and_set_word()) when only clearing (Ilpo
Järvinen)
- Add pci_get_base_class() to simplify finding devices using base
class only (ignoring subclass and programming interface) (Sui
Jingfeng)
- Add pci_is_vga(), which includes ancient PCI_CLASS_NOT_DEFINED_VGA
devices from before the Class Code was added to PCI (Sui Jingfeng)
- Use pci_is_vga() for vgaarb, sysfs "boot_vga", virtio, qxl to
include ancient VGA devices (Sui Jingfeng)
Resource management:
- Make pci_assign_unassigned_resources() non-init because sparc uses
it after init (Randy Dunlap)
Driver binding:
- Retain .remove() and .probe() callbacks (previously __init) because
sysfs may cause them to be called later (Uwe Kleine-König)
- Prevent xHCI driver from claiming AMD VanGogh USB3 DRD device, so
it can be claimed by dwc3 instead (Vicki Pfau)
PCI device hotplug:
- Add Ampere Altra Attention Indicator extension driver for acpiphp
(D Scott Phillips)
Power management:
- Quirk VideoPropulsion Torrent QN16e with longer delay after reset
(Lukas Wunner)
- Prevent users from overriding drivers that say we shouldn't use
D3cold (Lukas Wunner)
- Avoid PME from D3hot/D3cold for AMD Rembrandt and Phoenix USB4
because wakeup interrupts from those states don't work if amd-pmc
has put the platform in a hardware sleep state (Mario Limonciello)
IOMMU:
- Disable ATS for Intel IPU E2000 devices with invalidation message
endianness erratum (Bartosz Pawlowski)
Error handling:
- Factor out interrupt enable/disable into helpers (Kai-Heng Feng)
Peer-to-peer DMA:
- Fix flexible-array usage in struct pci_p2pdma_pagemap in case we
ever use pagemaps with multiple entries (Gustavo A. R. Silva)
ASPM:
- Revert a change that broke when drivers disabled L1 and users later
enabled an L1.x substate via sysfs, and fix a similar issue when
users disabled L1 via sysfs (Heiner Kallweit)
Endpoint framework:
- Fix double free in __pci_epc_create() (Dan Carpenter)
- Use IS_ERR_OR_NULL() to simplify endpoint core (Ruan Jinjie)
Cadence PCIe controller driver:
- Drop unused "is_rc" member (Li Chen)
Freescale Layerscape PCIe controller driver:
- Enable 64-bit addressing in endpoint mode (Guanhua Gao)
Intel VMD host bridge driver:
- Fix multi-function header check (Ilpo Järvinen)
Microsoft Hyper-V host bridge driver:
- Annotate struct hv_dr_state with __counted_by (Kees Cook)
NVIDIA Tegra194 PCIe controller driver:
- Drop setting of LNKCAP_MLW (max link width) since dw_pcie_setup()
already does this via dw_pcie_link_set_max_link_width() (Yoshihiro
Shimoda)
Qualcomm PCIe controller driver:
- Use PCIE_SPEED2MBS_ENC() to simplify encoding of link speed
(Manivannan Sadhasivam)
- Add a .write_dbi2() callback so DBI2 register writes, e.g., for
setting the BAR size, work correctly (Manivannan Sadhasivam)
- Enable ASPM for platforms that use 1.9.0 ops, because the PCI core
doesn't enable ASPM states that haven't been enabled by the
firmware (Manivannan Sadhasivam)
Renesas R-Car Gen4 PCIe controller driver:
- Add DesignWare core support (set max link width, EDMA_UNROLL flag,
.pre_init(), .deinit(), etc) for use by R-Car Gen4 driver
(Yoshihiro Shimoda)
- Add driver and DT schema for DesignWare-based Renesas R-Car Gen4
controller in both host and endpoint mode (Yoshihiro Shimoda)
Xilinx NWL PCIe controller driver:
- Update ECAM size to support 256 buses (Thippeswamy Havalige)
- Stop setting bridge primary/secondary/subordinate bus numbers,
since PCI core does this (Thippeswamy Havalige)
Xilinx XDMA controller driver:
- Add driver and DT schema for Zynq UltraScale+ MPSoCs devices with
Xilinx XDMA Soft IP (Thippeswamy Havalige)
Miscellaneous:
- Use FIELD_GET()/FIELD_PREP() to simplify and reduce use of _SHIFT
macros (Ilpo Järvinen, Bjorn Helgaas)
- Remove logic_outb(), _outw(), outl() duplicate declarations (John
Sanpe)
- Replace unnecessary UTF-8 in Kconfig help text because menuconfig
doesn't render it correctly (Liu Song)"
* tag 'pci-v6.7-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (102 commits)
PCI: qcom-ep: Add dedicated callback for writing to DBI2 registers
PCI: Simplify pcie_capability_clear_and_set_word() to ..._clear_word()
PCI: endpoint: Fix double free in __pci_epc_create()
PCI: xilinx-xdma: Add Xilinx XDMA Root Port driver
dt-bindings: PCI: xilinx-xdma: Add schemas for Xilinx XDMA PCIe Root Port Bridge
PCI: xilinx-cpm: Move IRQ definitions to a common header
PCI: xilinx-nwl: Modify ECAM size to enable support for 256 buses
PCI: xilinx-nwl: Rename the NWL_ECAM_VALUE_DEFAULT macro
dt-bindings: PCI: xilinx-nwl: Modify ECAM size in the DT example
PCI: xilinx-nwl: Remove redundant code that sets Type 1 header fields
PCI: hotplug: Add Ampere Altra Attention Indicator extension driver
PCI/AER: Factor out interrupt toggling into helpers
PCI: acpiphp: Allow built-in drivers for Attention Indicators
PCI/portdrv: Use FIELD_GET()
PCI/VC: Use FIELD_GET()
PCI/PTM: Use FIELD_GET()
PCI/PME: Use FIELD_GET()
PCI/ATS: Use FIELD_GET()
PCI/ATS: Show PASID Capability register width in bitmasks
PCI/ASPM: Fix L1 substate handling in aspm_attr_store_common()
...
When firmware status is invalid, assign -EINVAL to ret as ret is '0' at
that point and returning success is incorrect when firmware status is
invalid.
Fixes: a51d8ba03a ("ALSA: hda: cs35l41: Check CSPL state after loading firmware")
Signed-off-by: Harshit Mogalapalli <harshit.m.mogalapalli@oracle.com>
Link: https://lore.kernel.org/r/20231030070836.3234385-1-harshit.m.mogalapalli@oracle.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The newly introduced function is global but only called in this one
file and has no extern prototype, so it should probably be static:
sound/pci/hda/cs35l41_hda.c:733:5: error: no previous prototype for 'cs35l41_verify_id' [-Werror=missing-prototypes]
733 | int cs35l41_verify_id(struct cs35l41_hda *cs35l41, unsigned int *regid, unsigned int *reg_revid)
Fixes: 881b7bce0c ("ALSA: hda: cs35l41: Run boot process during resume callbacks")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20231027152515.482411-1-arnd@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CSPL firmware should be in RUNNING or PAUSED state after loading.
If not, the firmware has not been loaded correctly, and we can unload
it and pass the error up.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-8-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Given the part is about to reset due to system suspend, and we are
already in hibernate, there is no need to wake up the amp, just to get
it ready to be reset. We just need to ensure cs_dsp is ready for reset
by resetting the states.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-7-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To ensure the chip has correctly reset during probe and system suspend,
we need to force a software reset, in case of systems where the
hardware reset is not available.
The software reset register was labelled as volatile but not readable,
however, it is readable, (just returns 0x0). Adding it to readable
registers means it will be correctly treated as volatile, and thus
will not be cached.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-6-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
During initial probe, after reset is asserted for the first time, the
driver goes through a boot process to ensure the amp is ready to be
used. This involves verifying a boot flag, as well as verifying the
chip ids.
This is necessary since it is possible for the amp to have been fully
reset by the system suspend calls.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-5-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To ensure we are in a known state, exiting from reset at the point of
probe or in system resume, assert reset before we de-assert it.
Since the BIOS may enter into a pre-boot environment to control the
amps (for example for boot beep), we need to ensure we start from a
known, reset state prior to probe or system resume.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some system suspend modes may remove power supplies.
To ensure we are not running during this time, we should assert reset.
Note: since the amps use a shared reset, asserting reset prior to
system suspend only works if the amps are suspended in the reverse
order to probe.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This laptop has an incorrect setting in its _DSD for boost type, but
the rest of the _DSD is correct, and we can still use the reset label
to obtain the reset gpio.
Also fix channel map so that amp 0 is right, and amp 1 is left.
Fixes: 581523ee36 ("ALSA: hda: cs35l41: Override the _DSD for HP Zbook Fury 17 G9 to correct boost type")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231026150558.2105827-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is quite a large set of changes but mostly due to API cleanups and
in driver specific ways rather than due to anything subsystem wide.
Highlights include:
- Standardisation of API prefixes on snd_soc_, removing asoc_.
- GPIO API usage improvements.
- Support for HDA patches.
- Lots of work on SOF, including crash dump support.
- Support for AMD platforms with es83xx, Awinc AT87390, many Intel
platforms, many Mediatek platforms, Qualcomm SM6115, Richtek RTQ9128
and Texas Instruments TAS575x.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmUy6X8ACgkQJNaLcl1U
h9Cv7Qf+PO4ucl/rFITWAp2Ta9fw7Z5J6UCiXiR54TPgAiLJrpKSi3rbYTXjO90Y
1NNOdoMKr109zdOpdSZI7EX0GgWQbGbdB40nxESdTcojAloRH0jt4RaF7G7B7+86
b8PGlVPLLV/4zFf9f2gpEKPcKhRRRKYOBIEB+amfjWpdXVrqPD3zS/S16Q3Hn4Gy
Fx9b9X/lVDG9uqJomHpunEdViZjkm5CCNzdyAhHH99afiqSe//pevx6/FpzAHyng
AZgE9Yfq4Xw4pdzDdGVfYC+L1GZiHIDRzsusz6aPA5nrMhSn0ru8PMGtmQQTzyhb
PLYw0OW8cWymfqwal8wrNGJfSZ8IGA==
=lN5P
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.7' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.7
This is quite a large set of changes but mostly due to API cleanups and
in driver specific ways rather than due to anything subsystem wide.
Highlights include:
- Standardisation of API prefixes on snd_soc_, removing asoc_.
- GPIO API usage improvements.
- Support for HDA patches.
- Lots of work on SOF, including crash dump support.
- Support for AMD platforms with es83xx, Awinc AT87390, many Intel
platforms, many Mediatek platforms, Qualcomm SM6115, Richtek RTQ9128
and Texas Instruments TAS575x.
[ the merge conflicts around SOF Intel HD-audio and CS35L41 subcodec
drivers are resolved here -- tiwai ]
Now that all drivers have moved from modprobe loading to
handling -EPROBE_DEFER, we can remove the argument again.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20231009115437.99976-14-maarten.lankhorst@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that we can use -EPROBE_DEFER, it's no longer required to spin off
the snd_hdac_i915_init into a workqueue.
Use the -EPROBE_DEFER mechanism instead, which must be returned in the
probe function.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231009115437.99976-11-maarten.lankhorst@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Xe is a new GPU driver that re-uses the display (and sound) code from
i915. It's no longer possible to load i915, as the GPU can be driven
by the xe driver instead.
The new behavior will return -EPROBE_DEFER, and wait for a compatible
driver to be loaded instead of modprobing i915.
Converting all drivers at the same time is a lot of work, instead we
will convert each user one by one.
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20231009115437.99976-8-maarten.lankhorst@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Extract nifty FILE_LINE useful for printk style debugging:
printk("%s\n", FILE_LINE);
It should not be used en mass probably because __FILE__ string literals
can be merged while FILE_LINE's won't. But for debugging it is what
the doctor ordered.
Don't add leading and trailing underscores, they're painful to type.
Trust me, I've tried both versions.
Link: https://lkml.kernel.org/r/ebf12ac4-5a61-4b12-b8b0-1253eb371332@p183
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Kees Cook <keescook@chromium.org>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
ASUS platform Headset Mic was disable by default.
Assigned verb table for Mic pin will enable it.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1155d914c20c40569f56d36c79254879@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This HP Laptop uses ALC236 codec with COEF 0x07 controlling the
mute LED. Enable existing quirk for this device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20231016221328.1521674-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
AudioDSP firmware is the one who kicks SDxFIFOS calculation when a
stream is decoupled mode. During firmware bring up procedure, there is
no firmware running and the code-loading stream is always a decoupled
one. So, there is none to trigger the calculation and we end up with
false-positive timeout (-110) messages.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20231006102857.749143-4-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SDxFIFOS register indicates the fifo size directly. There is no need to
modify the value after reading the register.
Signed-off-by: Cezary Rojewski <cezary.rojewski@intel.com>
Link: https://lore.kernel.org/r/20231006102857.749143-3-cezary.rojewski@intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
While grep'ing for SIS7012, I noticed that there is
only one reference to it in sound/pci/intel8x0m.c,
while most of its code lives in sound/pci/intel8x0.c.
This probably was a simple copy'n'paste mistake, as
the sound/pci/intel8x0m.c driver implements support
for SIS7013 (see DEVICE_SIS), and the two devices
seem to share the same behavior / registers.
Signed-off-by: Thomas Perl <m@thp.io>
Link: https://lore.kernel.org/r/5E4B5CA1-1109-4C82-A581-838ACF19A15D@thp.io
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Intel RVP board (0x12cc) has Headset Mic issue for reboot.
If system plugged headset when system reboot the headset Mic was gone.
Fixes: 1a93f10c5b ("ALSA: hda/realtek: Add "Intel Reference board" and "NUC 13" SSID in the ALC256")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/28112f54c0c6496f97ac845645bc0256@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is an unlikely but possible double free when loading firmware,
and a missing free calls if a firmware is successfully requested but
the coefficient file request fails, leading to the fallback firmware
request occurring without clearing the previously loaded firmware.
Fixes: cd40dad2ca ("ALSA: hda: cs35l41: Ensure firmware/tuning pairs are always loaded")
Reported-by: kernel test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/r/202309291331.0JUUQnPT-lkp@intel.com/
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20231003142138.180108-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The "ret" variable is zero but we should return -EINVAL.
Fixes: 2144833e7b ("ALSA: hda: cirrus_scodec: Add KUnit test")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/5eea7fd5-67c8-4ed4-b5b3-b85dfb7572cc@moroto.mountain
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Prepare for the coming implementation by GCC and Clang of the __counted_by
attribute. Flexible array members annotated with __counted_by can have
their accesses bounds-checked at run-time checking via CONFIG_UBSAN_BOUNDS
(for array indexing) and CONFIG_FORTIFY_SOURCE (for strcpy/memcpy-family
functions).
As found with Coccinelle[1], add __counted_by for struct hda_conn_list.
[1] https://github.com/kees/kernel-tools/blob/trunk/coccinelle/examples/counted_by.cocci
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.com>
Cc: Cezary Rojewski <cezary.rojewski@intel.com>
Cc: alsa-devel@alsa-project.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: https://lore.kernel.org/r/20230922175042.work.547-kees@kernel.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the CS35L41 amp is requested to mute using the ACPI
notification mechanism, userspace is not notified that the amp
is muted. To allow userspace to know about the mute, add an
ALSA control which tracks the forced mute override.
This control does not track the overall mute state of the amp,
since the amp is only unmuted during playback anyway, instead
it tracks the mute override request from the ACPI notification.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230921162849.1988124-5-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some laptops require a hardware based mute system, where when a hotkey
is pressed, it forces the amp to be muted.
For CS35L41, when the hotkey is pressed, an acpi notification is sent
to the CS35L41 Device Node. The driver needs to handle this notification
and call a _DSM function to retrieve the mute state.
Since the amp is only muted during playback, the driver will only mute
or unmute if playback is occurring, otherwise it will save the mute
state for when playback starts.
This uses the ACPI Notification mechanism, where a handler has been
registered in the component master, which notifies each amp through
the component binding.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230921162849.1988124-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For systems which have support for ACPI notifications, add a mechanism to
register a handler for ACPI notifications and then call the acpi_notify
api on the bound components.
Registering a handler in the Realtek HDA driver, allows a single handler to
be registered, which then calls into all the components, rather than
attempting to register the same handler multiple times, once for each
component.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230921162849.1988124-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some systems support a notification from ACPI, which can be used
for different things.
Only one handler can be registered for the acpi notification, but all
amps need to receive that notification, we can register a single handler
inside the component master, so that it can then notify through the
component framework.
This is required to support mute notifications from ACPI.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230921162849.1988124-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is merge model ALC287_FIXUP_THINKPAD_I2S_SPK and
ALC287_FIXUP_CS35L41_I2C_2_THINKPAD_ACPI.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Fixes: f7b069cf08 ("ALSA: hda/realtek: Fix generic fixup definition for cs35l41 amp")
Link: https://lore.kernel.org/r/82a45234327c4c50b4988a27e9f64c37@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The KUnit test for cirrus_scodec uses GPIO library functions so select
GPIOLIB in Kconfig.
This fixes the ld failures on builds that didn't already select GPIOLIB.
ld: vmlinux.o: in function `cirrus_scodec_test_gpio_get':
sound/pci/hda/cirrus_scodec_test.c:40: undefined reference to
`gpiochip_get_data'
ld: vmlinux.o: in function `cirrus_scodec_test_gpio_probe':
sound/pci/hda/cirrus_scodec_test.c:94: undefined reference to
`gpiochip_generic_request'
ld: sound/pci/hda/cirrus_scodec_test.c:94: undefined reference to
`gpiochip_generic_free'
ld: sound/pci/hda/cirrus_scodec_test.c:95: undefined reference to
`devm_gpiochip_add_data_with_key'
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309201646.NnjfKPWk-lkp@intel.com/
Fixes: 2144833e7b ("ALSA: hda: cirrus_scodec: Add KUnit test")
Link: https://lore.kernel.org/r/20230920090338.29345-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
New platform SSID:0x231f.
0x17 was only speaker pin, DAC assigned will be 0x03. Headphone
assigned to 0x02.
Playback via headphone will get EQ filter processing.
So, it needs to swap DAC.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/8d63c6e360124e3ea2523753050e6f05@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use RUNTIME_PM_OPS() instead of the old SET_RUNTIME_PM_OPS().
This means we don't need __maybe_unused on the functions.
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230919081153.19793-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a KUnit test for cirrus_scodec_get_speaker_id(). It is impractical
to have enough hardware with every possible permutation of speaker id.
So use a test harness to test all theoretically supported options.
The test harness consists of:
- a mock GPIO controller.
- a mock struct device to represent the scodec driver
- software nodes to provide the fwnode info that would normally come
from ACPI.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230918095129.440-3-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add handling of the "spk-id-gpios" _DSD property. If present, the
value indicated by the GPIOs is appended to the subsystem-id
part of the firmware name to load the appropriate tunings for that
speaker.
Some manufacturers use multiple sources of speakers, which need
different tunings for best performance. On these models the type
of speaker fitted is indicated by the values of one or more GPIOs.
The number formed by the GPIOs identifies the tuning required.
The speaker ID is only used in combination with a _SUB identifier
because the value is only meaningful if the exact model is known.
The code to get the speaker ID value has been implemented as a
new library so that the cs35l41_hda driver can be switched in
future to share common code. This library can be extended for
other common functionality shared by Cirrus Logic amp drivers.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230918095129.440-2-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The filling of card->longname can be gracefully truncated, as it's
only informative. Use scnprintf() and suppress the superfluous
compile warning with -Wformat-truncation.
Link: https://lore.kernel.org/r/20230915091313.5988-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
add_control_with_pfx() constructs a mixer name element with the fixed
size, and it got compile warnings with -Wformat-truncation.
Although the size overflow is very unlikely, let's have a sanity check
of the string size and returns the error if it really doesn't fit
instead of silent truncation.
Link: https://lore.kernel.org/r/20230915082802.28684-14-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CMIPCI driver got compile warnings with -Wformat-truncation at a
couple of plain sprintf() usages. Use scnprintf() for filling the
longname string for avoiding the warnings.
Link: https://lore.kernel.org/r/20230915082802.28684-13-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In cs35l56_hda_read_acpi() do not return if ACPI _SUB is missing.
A missing _SUB means that the driver cannot load a system-specific
firmware, because the firmware is identified by the _SUB. But it can
fallback to a generic firmware. Unfortunately this was being handled
by immediately returning 0, which would skip the remaining ACPI
configuration in cs35l56_hda_read_acpi() and so it would not get the
RESET GPIO.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Link: https://lore.kernel.org/r/20230914152525.20829-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo ThinkCentre M70q had boot up pop noise.
Disable power save will solve pop issue.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/315900e2efef42fd9855eacfeb443abd@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The final return in cs35l56_hda_posture_get() was returning the
value of 'ret', but ret is always zero at this point. So this
can be a simple 'return 0'.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230914140852.7112-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
UX3402VA and UX3402ZA models require different hex values, so comibining
them into one model is incorrect.
Fixes: 491a4ccd8a ("ALSA: hda/realtek: Add quirk for ASUS Zenbook using CS35L41")
Signed-off-by: Knyazev Arseniy <poseaydone@ya.ru>
Link: https://lore.kernel.org/r/20230913053343.119798-1-poseaydone@ya.ru
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Do not allow the CS35L56 to be put into its lowest power
"hibernation" mode. This only affects I2C because "hibernation"
is already disabled on SPI.
Recent firmwares need a different wake-up sequence. Until
that sequence has been specified, the chip "hibernation" mode
must be disabled otherwise it can intermittently fail to wake.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230912132739.3478441-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If system has two speakers and one connect to 0x14 pin, use this
function will disable it.
Fixes: e43252db7e ("ALSA: hda/realtek - ALC287 I2S speaker platform support")
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/e3f2aac3fe6a47079d728a6443358cc2@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Driver remove() must call pm_runtime_dont_use_autosuspend().
Drivers that call pm_runtime_use_autosuspend() must disable
it in driver remove(). Unfortunately until recently this was
only mentioned in 1 line in a 900+ line document so most
people hadn't noticed this. It has only recently been added
to the kerneldoc of pm_runtime_use_autosuspend().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Link: https://lore.kernel.org/r/20230908101223.2656901-1-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the remaining dev_err() calls in probe() with dev_err_probe(),
to improve consistency.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230907171010.1447274-12-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
According to the documentation, drivers are responsible for undoing at
removal time all runtime PM changes done during probing.
Hence, add the missing calls to pm_runtime_dont_use_autosuspend(), which
are necessary for undoing pm_runtime_use_autosuspend().
Fixes: 1873ebd30c ("ALSA: hda: cs35l41: Support Hibernation during Suspend")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230907171010.1447274-11-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
If component_add() fails, probe() returns without calling
pm_runtime_put(), which leaves the runtime PM usage counter incremented.
Fix the issue by jumping to err_pm label and drop the now unnecessary
pm_runtime_disable() call.
Fixes: 7b2f3eb492 ("ALSA: hda: cs35l41: Add support for CS35L41 in HDA systems")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230907171010.1447274-10-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Enabling the active/passive shared boosts requires setting SYNC_EN, but
*not* before receiving the PLL Lock signal.
Due to improper error handling, it was not obvious that waiting for the
completion operation times out and, consequently, the shared boost is
never activated.
Further investigations revealed the signal is triggered while
snd_pcm_start() is executed, right after receiving the
SNDRV_PCM_TRIGGER_START command, which happens long after the
SND_SOC_DAPM_PRE_PMU event handler is invoked as part of
snd_pcm_prepare(). That is where cs35l41_global_enable() is called
from.
Increasing the wait duration doesn't help, as it only causes an
unnecessary delay in the invocation of snd_pcm_start(). Moving the wait
and the subsequent regmap operations to the SNDRV_PCM_TRIGGER_START
callback is not a solution either, since they would be executed in an
IRQ-off atomic context.
Solve the issue by setting the SYNC_EN bit in PWR_CTRL3 register right
after receiving the PLL Lock interrupt.
Additionally, drop the unnecessary writes to PWR_CTRL1 register, part of
the original mdsync_up_seq, which would have toggled GLOBAL_EN with
unwanted consequences on PLL locking behavior.
Fixes: f503056493 ("ALSA: cs35l41: Add shared boost feature")
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@collabora.com>
Reviewed-by: David Rhodes <david.rhodes@cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230907171010.1447274-5-cristian.ciocaltea@collabora.com
Signed-off-by: Mark Brown <broonie@kernel.org>
0x17 was only speaker pin, DAC assigned will be 0x03. Headphone
assigned to 0x02.
Playback via headphone will get EQ filter processing. So,it needs to
swap DAC.
Tested-by: Mark Pearson <mpearson@lenovo.com>
Signed-off-by: Kailang Yang <kailang@realtek.com>
Link: https://lore.kernel.org/r/4e4cfa1b3b4c46838aecafc6e8b6f876@realtek.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The LED for the mic mute button is controlled by GPIO2.
The mute button LED is slightly more complex, it's controlled by two bits
in coeff 0x0b.
Signed-off-by: Fabian Vogt <fabian@ritter-vogt.de>
Link: https://lore.kernel.org/r/2693091.mvXUDI8C0e@fabians-envy
Signed-off-by: Takashi Iwai <tiwai@suse.de>
struct i2c_driver::probe_new is about to go away. Switch the driver to
use the probe callback with the same prototype.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Fixes: 5be27f1e3e ("ALSA: hda/tas2781: Add tas2781 HDA driver")
Link: https://lore.kernel.org/r/20230824200219.9569-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Before committing 79597c8bf6, *rac97 always be NULL if there is
an error. When error happens, make sure *rac97 is NULL is safer.
For examble, in snd_vortex_mixer():
err = snd_ac97_mixer(pbus, &ac97, &vortex->codec);
vortex->isquad = ((vortex->codec == NULL) ?
0 : (vortex->codec->ext_id&0x80));
If error happened but vortex->codec isn't NULL, this may cause some
problems.
Move the judgement order to be clearer and better.
Fixes: 79597c8bf6 ("ALSA: ac97: Fix possible NULL dereference in snd_ac97_mixer")
Suggested-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Su Hui <suhui@nfschina.com>
Link: https://lore.kernel.org/r/20230823025212.1000961-1-suhui@nfschina.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CS35L41 HDA driver requires ACPI to contain correct _DSD properties to
correctly configure the device. Whilst the HP Zbook Fury 17 G9 contains
valid _DSD properties, the boost type has been configured incorrectly
in the _DSD for this laptop. We can override these properties to fix
the boost type.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230823143956.755758-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like a few other drivers, YMFPCI driver needs to clean up with
snd_card_free() call at an error path of the probe; otherwise the
other devres resources are released before the card and it results in
the UAF.
This patch uses the helper for handling the probe error gracefully.
Fixes: f33fc15767 ("ALSA: ymfpci: Create card with device-managed snd_devm_card_new()")
Cc: <stable@vger.kernel.org>
Reported-and-tested-by: Takashi Yano <takashi.yano@nifty.ne.jp>
Closes: https://lore.kernel.org/r/20230823135846.1812-1-takashi.yano@nifty.ne.jp
Link: https://lore.kernel.org/r/20230823161625.5807-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the rme9652 driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Link: https://lore.kernel.org/r/20230815190136.8987-14-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the hdsp driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Link: https://lore.kernel.org/r/20230815190136.8987-13-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the rme96 driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Link: https://lore.kernel.org/r/20230815190136.8987-12-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the rme32 driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Link: https://lore.kernel.org/r/20230815190136.8987-11-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the nm256 driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants.
Link: https://lore.kernel.org/r/20230815190136.8987-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the korg1212 driver code to use the new unified
PCM copy callback. The open-coded conditional memory copies are
replaced with simpler copy_from/to_iter() calls.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Link: https://lore.kernel.org/r/20230815190136.8987-9-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch converts the es1938 driver code to use the new unified PCM
copy callback. It's a straightforward conversion from *_user() to
*_iter() variants in most parts.
Note that copy_from/to_iter() returns the copied bytes, hence the
error condition is adjusted accordingly.
Link: https://lore.kernel.org/r/20230815190136.8987-8-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Create tas2781 side codec HDA driver for Lenovo Laptops. The quantity
of the speakers has been define in ACPI. All of the tas2781s in the
laptop will be aggregated as one audio speaker. The code supports
realtek codec as the primary codec. Code offers several controls for
digtial/analog gain setting during playback, and other for eq params
setting in case of different audio profiles, such as music, voice,
movie, etc.
[ adjusted patch to be applied to the latest for-next branch -- tiwai ]
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://lore.kernel.org/r/20230818085836.1442-2-shenghao-ding@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Integrate tas2781 configs for Lenovo Laptops. All of the tas2781s in the
laptop will be aggregated as one audio device. The code support realtek
as the primary codec. Rename "struct cs35l41_dev_name" to
"struct scodec_dev_name" for all other side codecs instead of the certain
one.
Signed-off-by: Shenghao Ding <shenghao-ding@ti.com>
Link: https://lore.kernel.org/r/20230818085836.1442-1-shenghao-ding@ti.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Like control and PCM devices, it's better to avoid the embedded struct
device for hwdep (although it's more or less well working), too.
Change it to allocate via snd_device_alloc(), and free the memory at
the common snd_hwdep_free().
Reviewed-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Tested-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20230816160252.23396-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
cs35l41_prop_model is only used in cs35l41_hda_property.c now,
change it to static.
Fixes: ef4ba63f12 ("ALSA: hda: cs35l41: Support systems with missing _DSD properties")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20230817014252.1511232-1-yangyingliang@huawei.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Set spec->en_3kpull_low default to true.
Then fillback ALC236 and ALC257 to false.
Additional note: this addresses a regression caused by the previous
fix 69ea4c9d02 ("ALSA: hda/realtek - remove 3k pull low procedure").
The previous workaround was applied too widely without necessity,
which resulted in the pop noise at PM again. This patch corrects the
condition and restores the old behavior for the devices that don't
suffer from the original problem.
Fixes: 69ea4c9d02 ("ALSA: hda/realtek - remove 3k pull low procedure")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=217732
Link: https://lore.kernel.org/r/01e212a538fc407ca6edd10b81ff7b05@realtek.com
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some systems using CS35L41 with HDA were released without some
required _DSD properties in ACPI. To support these special cases,
add an api to configure the correct properties for systems with
this issue.
This initial commit moves the no _DSD support for Lenovo
Legion Laptops (CLSA0100, CLSA0101) into a new framework which
can be extended to support additional laptops in the future.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230815161033.3519-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All I2C Dell Oasis models using CS35L41 have been changed to use SPI.
In addition, System 10280cc5 is no longer required.
Fixes: de90f5165b ("ALSA: hda/realtek: Add support for DELL Oasis 13/14/16 laptops")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230809142957.675933-3-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These HP G11 laptops use Realtek HDA codec combined with
2xCS35L41 Amplifiers using SPI or I2C with External Boost.
Laptop 103c8c26 has been removed as this has been replaced
by this new series of laptops.
Fixes: 3e10f6ca76 ("ALSA: hda/realtek: Add quirk for HP EliteBook G10 laptops")
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230809142957.675933-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
`strncpy` is deprecated for use on NUL-terminated destination strings [1].
A suitable replacement is `strscpy` [2] due to the fact that it
guarantees NUL-termination on its destination buffer argument which is
_not_ the case for `strncpy`!
It should be noted that the current implementation is unlikely to have a
bug because `drv_name` is a string literal with a size of 9 while
`card->driver` has a size of 16. However, it is probably worthwhile to
switch to a more robust and less ambiguous interface.
[1]: www.kernel.org/doc/html/latest/process/deprecated.html#strncpy-on-nul-terminated-strings
[2]: https://manpages.debian.org/testing/linux-manual-4.8/strscpy.9.en.html
Link: https://github.com/KSPP/linux/issues/90
Cc: linux-hardening@vger.kernel.org
Signed-off-by: Justin Stitt <justinstitt@google.com>
Link: https://lore.kernel.org/r/20230807-sound-pci-hda-v1-1-6d9cdcd085ca@google.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Print amp configuration information to be able to confirm ACPI
_DSD information (and other useful info) for each amp on each
system using CS35L41, without having to get the acpidump.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230802121235.467358-1-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The ACPI nodes for CS35L56 can contain an extra I2CSerialBusV2 that
is not a real device, it is an alias address.
This alias address will not be in the cirrus,dev-index array, so reject
any instantions with a device address not found in the array.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-10-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A tuning patch is always needed to enable the ASP audio port.
If the BIOS did not patch the firmware, then it is mandatory to
have a .bin file.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-9-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A RAM firmware can only be downloaded if the CS35L56 is currently
running from ROM firmware. The driver must not try to overwrite
the RAM if the CS35L56 is already running from that RAM.
Firmware can be downloaded in these two cases:
- The BIOS has already patched the firmware (secured mode).
In this case the firmware files will only contain tunings that
are safe to overwrite.
- The CS35L56 is running the built-in ROM firmware.
After a RAM firmware has been downloaded it can only be cleared by
hard resetting CS35L56. Some systems only hard-reset during
power-on and do not give the driver control of hard reset.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-8-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If cs35l56_hda_fw_load() successfully called cs_dsp_power_up() the error
path must balance that with a call to cs_dsp_power_down().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-7-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In cs35l56_hda_unbind() cs_dsp_power_down() must be called to cleanup
before calling cs_dsp_remove cs_dsp_remove().
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-6-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Always call cs_dsp_power_up() and cs_dsp_run() in
cs35l56_hda_fw_load() even if there aren't any firmware files
to download. Also, if there aren't any firmware files to
download there is no need to do cs35l56_firmware_shutdown() and
cs35l56_system_reset().
If there aren't any firmware files there's no need to write
anything to the CS35L56 registers to make it work - it will
already be running the ROM firmware. So it's not strictly
necessary to start cs_dsp.
But it's perfectly ok to call cs_dsp_power_up() and
cs_dsp_run() without downloading any firmware. This avoids
having to support a state where audio is playing but cs_dsp
is not running.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-5-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When firmware is reloaded after a system resume cs_dsp_power_down() should
be called before calling cs_dsp_power_up().
The fw_patched flag should also be cleared and only set again if the
firmware download succeeded.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-4-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Only call regcache_mark_dirty() in cs35l56_hda_fw_load() if
the CS35L56 was SYSTEM_RESET.
recache_mark_dirty() changes the behaviour of regcache_sync()
to write out cache values that are not the default value, and
skip cache values that are the default.
AUDIO_REINIT does not reset the registers. regcache_mark_dirty()
after AUDIO_REINIT could cause the regcache_sync() to sync
registers incorrectly because it will assume that all registers
have reset to default.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-3-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the call to cs_dsp_run() in cs35l56_hda_fw_load() so that it
is after the CS35L56 has been reset/reinit'd and the regmap
cache has been synced.
cs_dsp_run() syncs up ALSA control cache values with the DSP memory
so this must not be done until the firmware has reinitialized.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230731165726.7940-2-rf@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Smatch complains that this return should be a goto:
sound/pci/hda/cs35l56_hda.c:910 cs35l56_hda_common_probe()
warn: missing unwind goto?
The goto error disables cansleep so that seems reasonable.
Fixes: 73cfbfa9ca ("ALSA: hda/cs35l56: Add driver for Cirrus Logic CS35L56 amplifier")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Link: https://lore.kernel.org/r/465160f4-b7cf-41d5-931e-d6c9e68fa3c7@moroto.mountain
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This laptop has CS35L41 amp connected via I2C.
With this patch speakers begin to work if the
missing _DSD properties are added to ACPI tables.
Signed-off-by: Pavel Asyutchenko <svenpavel@gmail.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230726223732.20775-1-svenpavel@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This HP Notebook used ALC236 codec with COEF 0x07 idx 1 controlling
the mute LED. Enable already existing quirk for this device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230725111509.623773-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Here's an initial batch of updates for ASoC for this release cycle.
We've got a bunch of new drivers in here, a bit of core work from
Morimoto-san and quite a lot of janitorial work. There's several
updates that pull in changes from other subsystems in order to build
on them:
- An adaptor to allow use of IIO DACs and ADCs in ASoC which pulls in
some IIO changes.
- Create a library function for intlog10() and use it in the NAU8825
driver.
- Include the ASoC tests, including the topology tests, in the default
KUnit full test coverage. This also involves enabling UML builds of
ALSA since that's the default KUnit test environment which pulls in
the addition of some stubs to the driver.
- More factoring out from Morimoto-san.
- Convert a lot of drivers to use the more modern maple tree register
cache.
- Support for AMD machines with MAX98388 and NAU8821, Cirrus Logic
CS35L36, Intel AVS machines with ES8336 and RT5663 and NXP i.MX93.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAmS/t9MACgkQJNaLcl1U
h9Dg4wf+Njvy5zphgUJlSJ7vNj7GtzgldnWwfQrb+19BOtv5HHIYg4e/Yr4eWdgc
rg5DGIGvr8sxYQ44TCA59sXdTuakkNF/ejDoj8AwNsr/J3sD6S+FTkV8qLFcgQ3r
+0ElZ26I2kd6gfvDlwHfa5rJVPCa7vrg3o6EHccqRX9CSyPJRlwRqRRj+w8ftZtV
rZ7Gapz3E4A3mBo7VIO/kEgI1uSmaShM8d4HoVmxJEKJ6lbyX8SIXMBzZVq5z/iX
DcnRaMPAMhgzytmdDJ7SjJuxL0EOd6p8Lnk0jILvO6U30Z7aTunzMuK/o0GHqFkm
eHveoHIU4gbt3YqDFgPosPlxi4OCgw==
=KJZq
-----END PGP SIGNATURE-----
Merge tag 'asoc-v6.6-early' of https://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v6.6
Here's an initial batch of updates for ASoC for this release cycle.
We've got a bunch of new drivers in here, a bit of core work from
Morimoto-san and quite a lot of janitorial work. There's several
updates that pull in changes from other subsystems in order to build
on them:
- An adaptor to allow use of IIO DACs and ADCs in ASoC which pulls in
some IIO changes.
- Create a library function for intlog10() and use it in the NAU8825
driver.
- Include the ASoC tests, including the topology tests, in the default
KUnit full test coverage. This also involves enabling UML builds of
ALSA since that's the default KUnit test environment which pulls in
the addition of some stubs to the driver.
- More factoring out from Morimoto-san.
- Convert a lot of drivers to use the more modern maple tree register
cache.
- Support for AMD machines with MAX98388 and NAU8821, Cirrus Logic
CS35L36, Intel AVS machines with ES8336 and RT5663 and NXP i.MX93.
Currently we only mute after playback has finished, and unmute
prior to setting global enable. To prevent any possible pops
and clicks, mute at probe, and then only unmute after global
enable is set.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-12-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To ensure consistency between the HDA core and the CS35L41 HDA
driver, add a device_link between them. This ensures that the
HDA core will suspend first, and resume second, meaning the
amp driver will not miss any events from the playback hook from
the HDA core during system suspend and resume.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-11-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to correctly pause audio on suspend, amps using external boost
require parts of the pause sequence to be called for all amps before moving
on to the next steps.
For example, as part of pausing the audio, the VSPK GPIO must be disabled,
but since this GPIO is controlled by one amp, but controls the boost for
all amps, it is required to separate the calls.
During playback this is achieved by using the pre and post playback hooks,
however during system suspend, this is not possible, so to separate the
calls, we use both the .prepare and .suspend calls to pause the audio.
Currently, for this reason, we do not restart audio on system resume.
However, we can support this by relying on the playback hook to resume
playback after system suspend.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-10-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use new hooks to ensure separation between play/pause actions,
as required by external boost.
External Boost on CS35L41 requires the amp to go through a
particular sequence of steps. One of these steps involes
the setting of a GPIO. This GPIO is connected to one or
more of the amps, and it may control the boost for all of
the amps. To ensure that the GPIO is set when it is safe
to do so, and to ensure that boost is ready for the rest of
the sequence to be able to continue, we must ensure that
the each part of the sequence is executed for each amp
before moving on to the next part of the sequence.
Some of the Play and Pause actions have moved from Open to
Prepare. This is because Open is not guaranteed to be called
again on system resume, whereas Prepare should.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-9-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These hooks can be used to add callbacks that would be run before and after
the main playback hooks. These hooks would be called for all amps, before
moving on to the next hook, i.e. pre_playback_hook would be called for
all amps, before the playback_hook is called for all amps, then finally
the post_playback_hook is called for all amps.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-8-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There are several steps required to put the system into system suspend.
Some of these steps may fail, so the driver should pass up the errors
if they occur.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-6-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to properly system suspend, it is necessary to unload the firmware
and ensure the chip is ready for shutdown (if necessary). If the system
is currently in runtime suspend, it is necessary to wake up the device,
and then make it ready. Currently, the wake does not correctly resync
the device, which may mean it cannot suspend correctly. Fix this by
performaing a resync.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-5-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, we do not check the return status of the pause command,
immediately after we load firmware. If the pause has failed,
the firmware is not running.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-4-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To enable the speaker output in external boost mode, 2 registers must
be set, one after another. The longer the time between the writes of
the two registers, the more likely, and more loudly a pop may occur.
To minimize this, an mbox command can be used to allow the firmware
to perform this action, minimizing any delay between write, thus
minimizing any pop or click as a result. The old method will remain
when running without firmware.
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230721151816.2080453-2-sbinding@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a driver for the Cirrus Logic CS35L56 amplifier. This uses the same
component binding API as the CS35L41 driver. This is not a standalone
HDA device; it provides control of the CS35L56 for systems that use a
combination of an HDA codec and CS35L56 amplifiers with audio routed
through the HDA codec.
The CS35L56 combines a high-performance mono audio amplifier, Class-H
tracking inductive boost converter, Halo Core(TM) DSP and a DC-DC boost
converter supporting Class-H tracking.
Control interfaces are I2C or SPI through the standard Linux I2C or SPI
bus framework.
Most chip functionality is controlled by on-board ROM firmware that is
always running. Firmware patches can be applied by the driver in the form
of a .wmfw file (firmware patch) and/or a .bin file (system tuning).
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230721132120.5523-12-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Add #includes of dependencies into hda_auto_parser.h and hda_generic.h
hda_auto_parser.h uses definitions in hda_local.h.
hda_generic.h uses definitions in hda_local.h and hda_auto_parser.h.
It also references struct hda_jack_callback, but only as a pointer.
This has been forward-declared so hda_jack.h only needs to be
included in source that actually uses it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Link: https://lore.kernel.org/r/20230721132120.5523-11-rf@opensource.cirrus.com
Signed-off-by: Mark Brown <broonie@kernel.org>
Switch order of Intel MTL and RPL codec entries to keep the codec device
id list nicely ordered. Also use the opportunity to fix the naming
to the convention used elsewhere in the drivers.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Bard Liao <yung-chuan.liao@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@linux.intel.com>
Link: https://lore.kernel.org/r/20230721135722.31288-2-peter.ujfalusi@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of open-code, use the new standard helper to manage vmaster
stuff for code simplification.
Also, handle the errors from the helper more properly instead of
silently ignoring.
The code changes the call order of snd_ctl_add() of the vmaster object
and its followers for avoiding the possible memory leaks at error
path. But there should be no difference in the functionality.
Link: https://lore.kernel.org/r/20230721071643.3631-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of open-code, use the new standard helper to manage vmaster
stuff for code simplification.
Also, handle the errors from the helper more properly instead of
silently ignoring.
Link: https://lore.kernel.org/r/20230721071643.3631-4-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of open-code, use the new standard helper to manage vmaster
stuff for code simplification.
Except for a debug print, there should be no functional change.
Link: https://lore.kernel.org/r/20230721071643.3631-3-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace an open code with the new snd_ctl_find_id_mixer().
There is no functional change.
Also, add the missing NULL checks in psc724_set_jack_state() to deal
with error cases.
Link: https://lore.kernel.org/r/20230720082108.31346-7-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Adding support for new Dell laptops using Cirrus Logic CS35L41
smart amplifiers with Realtek codec.
Signed-off-by: Stefan Binding <sbinding@opensource.cirrus.com>
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230720082022.13033-2-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Generic fixup for CS35L41 amplifies should not have vendor specific
chained fixup. For ThinkPad laptops with led issue, we can just add
specific fixup.
Fixes: a6ac60b36d (ALSA: hda/realtek: Fix mute led issue on thinkpad with cs35l41 s-codec)
Signed-off-by: Vitaly Rodionov <vitalyr@opensource.cirrus.com>
Link: https://lore.kernel.org/r/20230720082022.13033-1-vitalyr@opensource.cirrus.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few ALSA control API helpers like snd_ctl_rename(), snd_ctl_remove()
and snd_ctl_find_*() suppose the callers taking card->controls_rwsem.
But it's error-prone and fragile. This patch set tries to change
those API functions to take the card->controls>rwsem internally by
themselves, so that the drivers don't need to take care of lockings.
After applying this patch set, only a couple of places still touch
card->controls_rwsem (which are OK-ish as they need for traversing the
control linked list).
Link: https://lore.kernel.org/r/20230718141304.1032-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
-----BEGIN PGP SIGNATURE-----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=V5+5
-----END PGP SIGNATURE-----
Merge tag 'tags/ctl-lock-fixes-6.6' into for-next
ALSA: Make control API taking controls_rwsem consistently
A few ALSA control API helpers like snd_ctl_rename(), snd_ctl_remove()
and snd_ctl_find_*() suppose the callers taking card->controls_rwsem.
But it's error-prone and fragile. This patch set tries to change
those API functions to take the card->controls>rwsem internally by
themselves, so that the drivers don't need to take care of lockings.
After applying this patch set, only a couple of places still touch
card->controls_rwsem (which are OK-ish as they need for traversing the
control linked list).
Link: https://lore.kernel.org/r/20230718141304.1032-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that snd_ctl_find_id() takes the locking itself, we can get rid of
the messy locking in the caller side in snd_emu10k1_verify_controls().
Link: https://lore.kernel.org/r/20230718141304.1032-12-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For reducing the unnecessary use of controls_rwsem in the drivers,
this patch adds a new variant for snd_ctl_find_*() helpers:
snd_ctl_find_id_locked() and snd_ctl_find_numid_locked() look for a
kctl element inside the card->controls_rwsem -- that is, doing the
very same as what snd_ctl_find_id() and snd_ctl_find_numid() did until
now. snd_ctl_find_id() and snd_ctl_find_numid() remain same,
i.e. still unlocked version, but they will be switched to locked
version once after all callers are replaced.
The patch also replaces the calls of snd_ctl_find_id() and
snd_ctl_find_numid() in a few places; all of those are places where we
know that the functions are called properly with controls_rwsem held.
All others are without rwsem (although they should have been).
After this patch, we'll turn on the locking in snd_ctl_find_id() and
snd_ctl_find_numid() to be more race-free.
Link: https://lore.kernel.org/r/20230718141304.1032-10-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, snd_ctl_remove() requires its caller to take
card->controls_rwsem manually before the call for avoiding possible
races. However, many callers don't care and miss the locking.
Basically it's cumbersome and error-prone to enforce it to each
caller. Moreover, card->controls_rwsem is a field that should be used
only by internal or proper helpers, and it's not to be touched at
random external places.
This patch is an attempt to make those calls more consistent: now
snd_ctl_remove() takes the card->controls_rwsem internally, just like
other API functions for kctls. Since a few callers already take the
controls_rwsem locks, the patch removes those locks at the same time,
too.
Link: https://lore.kernel.org/r/20230718141304.1032-5-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HP Laptop 15s-eq2xxx uses ALC236 codec and controls the mute LED using
COEF 0x07 index 1. No existing quirk covers this configuration.
Adds a new quirk and enables it for the device.
Signed-off-by: Luka Guzenko <l.guzenko@web.de>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20230718161241.393181-1-l.guzenko@web.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use PCI device IDs from pci_ids.h header and while at it to simplify
declarations change to using PCI_DEVICE_DATA() macro for Intel IDs and
PCI_VDEVICE() for all other that have defined vendor.
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230717114511.484999-11-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of using local macro to match PCI device, use global one. As
Apollolake is Broxton-P successor that made it to the market, be precise
and use APL shortcut.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230717114511.484999-7-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Current code references 0x1a98 which is BXT-M (not -T as it is
commented) and it's an RVP, BXT-M B0 to be specific. From what we know
no BXT is available on market.
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mark Brown <broonie@kernel.org>
Reviewed-by: Cezary Rojewski <cezary.rojewski@intel.com>
Signed-off-by: Amadeusz Sławiński <amadeuszx.slawinski@linux.intel.com>
Link: https://lore.kernel.org/r/20230717114511.484999-5-amadeuszx.slawinski@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
- Remove the "log-like" parts, following the same logic as the previous
commit
- Unify format
- Add missing major contributors, including myself
- Sort entries in order of first contribution (Creative comes last for
optical reasons; they don't appear to have directly contributed
anyway)
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230715160839.326978-2-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Empty BUGS and TODO sections don't really help anyone, so remove them.
Version information is chronically outdated, and not really useful in a
git world anyway, so remove it as well.
Also remove duplicated (and outdated, of course) status section from
p16v.h (the one in p16v.c is in better shape).
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230715160839.326978-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
85;95;0c
This uses IRQs to track spontaneous changes to the word clock source
register.
FWIW, that this can happen in the first place is the reason why it is
futile to lock the clock source mixer setting while the device is open -
we can't consistently control the rate anyway. Though arguably, we
should reset any open streams when that happens, as they become
corrupted anyway.
Signed-off-by: Oswald Buddenhagen <oswald.buddenhagen@gmx.de>
Link: https://lore.kernel.org/r/20230715160738.326832-1-oswald.buddenhagen@gmx.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
