There exist configurations where the administrator or another management
entity has the foreknowledge of all the mac addresses of end systems
that are being bridged together.
In these environments, the administrator can statically configure known
addresses in the bridge FDB and disable flooding and learning on ports.
This makes it possible to turn off promiscuous mode on the interfaces
connected to the bridge.
Here is why disabling flooding and learning allows us to control
promiscuity:
Consider port X. All traffic coming into this port from outside the
bridge (ingress) will be either forwarded through other ports of the
bridge (egress) or dropped. Forwarding (egress) is defined by FDB
entries and by flooding in the event that no FDB entry exists.
In the event that flooding is disabled, only FDB entries define
the egress. Once learning is disabled, only static FDB entries
provided by a management entity define the egress. If we provide
information from these static FDBs to the ingress port X, then we'll
be able to accept all traffic that can be successfully forwarded and
drop all the other traffic sooner without spending CPU cycles to
process it.
Another way to define the above is as following equations:
ingress = egress + drop
expanding egress
ingress = static FDB + learned FDB + flooding + drop
disabling flooding and learning we a left with
ingress = static FDB + drop
By adding addresses from the static FDB entries to the MAC address
filter of an ingress port X, we fully define what the bridge can
process without dropping and can thus turn off promiscuous mode,
thus dropping packets sooner.
There have been suggestions that we may want to allow learning
and update the filters with learned addresses as well. This
would require mac-level authentication similar to 802.1x to
prevent attacks against the hw filters as they are limited
resource.
Additionally, if the user places the bridge device in promiscuous mode,
all ports are placed in promiscuous mode regardless of the changes
to flooding and learning.
Since the above functionality depends on full static configuration,
we have also require that vlan filtering be enabled to take
advantage of this. The reason is that the bridge has to be
able to receive and process VLAN-tagged frames and the there
are only 2 ways to accomplish this right now: promiscuous mode
or vlan filtering.
Suggested-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce a BR_PROMISC per-port flag that will help us track if the
current port is supposed to be in promiscuous mode or not. For now,
always start in promiscuous mode.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, ports on the bridge are capable of automatic
discovery of nodes located behind the port. This is accomplished
via flooding of unknown traffic (BR_FLOOD) and learning the
mac addresses from these packets (BR_LEARNING).
If the above functionality is disabled by turning off these
flags, the port requires static configuration in the form
of static FDB entries to function properly.
This patch adds functionality to keep track of all ports
capable of automatic discovery. This will later be used
to control promiscuity settings.
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The gfp parameter was added in:
commit 47be03a28c
Author: Amerigo Wang <amwang@redhat.com>
Date: Fri Aug 10 01:24:37 2012 +0000
netpoll: use GFP_ATOMIC in slave_enable_netpoll() and __netpoll_setup()
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reason for the gfp parameter was removed in:
commit c4cdef9b71
Author: dingtianhong <dingtianhong@huawei.com>
Date: Tue Jul 23 15:25:27 2013 +0800
bonding: don't call slave_xxx_netpoll under spinlocks
The slave_xxx_netpoll will call synchronize_rcu_bh(),
so the function may schedule and sleep, it should't be
called under spinlocks.
bond_netpoll_setup() and bond_netpoll_cleanup() are always
protected by rtnl lock, it is no need to take the read lock,
as the slave list couldn't be changed outside rtnl lock.
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing else that calls __netpoll_setup or ndo_netpoll_setup
requires a gfp paramter, so remove the gfp parameter from both
of these functions making the code clearer.
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Vlan code may need fdb change when changing mac address of bridge device
even if it is caused by the mac address changing of a bridge port.
Example configuration:
ip link set eth0 address 12:34:56:78:90:ab
ip link set eth1 address aa:bb:cc:dd:ee:ff
brctl addif br0 eth0
brctl addif br0 eth1 # br0 will have mac address 12:34:56:78:90:ab
bridge vlan add dev br0 vid 10 self
bridge vlan add dev eth0 vid 10
We will have fdb entry such that f->dst == NULL, f->vlan_id == 10 and
f->addr == 12:34:56:78:90:ab at this time.
Next, change the mac address of eth0 to greater value.
ip link set eth0 address ee:ff:12:34:56:78
Then, mac address of br0 will be recalculated and set to aa:bb:cc:dd:ee:ff.
However, an entry aa:bb:cc:dd:ee:ff will not be created and we will be not
able to communicate using br0 on vlan 10.
Address this issue by deleting and adding local entries whenever
changing the mac address of the bridge device.
If there already exists an entry that has the same address, for example,
in case that br_fdb_changeaddr() has already inserted it,
br_fdb_change_mac_address() will simply fail to insert it and no
duplicated entry will be made, as it was.
This approach also needs br_add_if() to call br_fdb_insert() before
br_stp_recalculate_bridge_id() so that we don't create an entry whose
dst == NULL in this function to preserve previous behavior.
Note that this is a slight change in behavior where the bridge device can
receive the traffic to the new address before calling
br_stp_recalculate_bridge_id() in br_add_if().
However, it is not a problem because we have already the address on the
new port and such a way to insert new one before recalculating bridge id
is taken in br_device_event() as well.
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Acked-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
And it can become static.
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix spelling errors in bridge driver.
Signed-off-by: Tan Xiaojun <tanxiaojun@huawei.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
bridge dev
When the following commands are executed:
brctl addbr br0
ifconfig br0 hw ether <addr>
rmmod bridge
The calltrace will occur:
[ 563.312114] device eth1 left promiscuous mode
[ 563.312188] br0: port 1(eth1) entered disabled state
[ 563.468190] kmem_cache_destroy bridge_fdb_cache: Slab cache still has objects
[ 563.468197] CPU: 6 PID: 6982 Comm: rmmod Tainted: G O 3.12.0-0.7-default+ #9
[ 563.468199] Hardware name: Bochs Bochs, BIOS Bochs 01/01/2007
[ 563.468200] 0000000000000880 ffff88010f111e98 ffffffff814d1c92 ffff88010f111eb8
[ 563.468204] ffffffff81148efd ffff88010f111eb8 0000000000000000 ffff88010f111ec8
[ 563.468206] ffffffffa062a270 ffff88010f111ed8 ffffffffa063ac76 ffff88010f111f78
[ 563.468209] Call Trace:
[ 563.468218] [<ffffffff814d1c92>] dump_stack+0x6a/0x78
[ 563.468234] [<ffffffff81148efd>] kmem_cache_destroy+0xfd/0x100
[ 563.468242] [<ffffffffa062a270>] br_fdb_fini+0x10/0x20 [bridge]
[ 563.468247] [<ffffffffa063ac76>] br_deinit+0x4e/0x50 [bridge]
[ 563.468254] [<ffffffff810c7dc9>] SyS_delete_module+0x199/0x2b0
[ 563.468259] [<ffffffff814e0922>] system_call_fastpath+0x16/0x1b
[ 570.377958] Bridge firewalling registered
--------------------------- cut here -------------------------------
The reason is that when the bridge dev's address is changed, the
br_fdb_change_mac_address() will add new address in fdb, but when
the bridge was removed, the address entry in the fdb did not free,
the bridge_fdb_cache still has objects when destroy the cache, Fix
this by flushing the bridge address entry when removing the bridge.
v2: according to the Toshiaki Makita and Vlad's suggestion, I only
delete the vlan0 entry, it still have a leak here if the vlan id
is other number, so I need to call fdb_delete_by_port(br, NULL, 1)
to flush all entries whose dst is NULL for the bridge.
Suggested-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Suggested-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: Ding Tianhong <dingtianhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some slave devices may have set a dev->needed_headroom value which is
different than the default one, most likely in order to prepend a
hardware descriptor in front of the Ethernet frame to send. Whenever a
new slave is added to a bridge, ensure that we update the
needed_headroom value accordingly to account for the slave
needed_headroom value.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This started out with fixing a sparse warning, then I realized that
the wrapper function br_netpoll_info could just be collapsed away
by rolling it into the enable code.
Also, eliminate unnecessary goto's
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a flag to control flood of unicast traffic. By default, flood is
on and the bridge will flood unicast traffic if it doesn't know
the destination. When the flag is turned off, unicast traffic
without an FDB will not be forwarded to the specified port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Reviewed-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow user to control whether mac learning is enabled on the port.
By default, mac learning is enabled. Disabling mac learning will
cause new dynamic FDB entries to not be created for a particular port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Keep a STP port path cost value if it was set by a user.
Don't replace it with the link-speed based path cost
whenever the link goes down and comes back up.
Reported-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 00cfec3748 (net: add a synchronize_net() in
netdev_rx_handler_unregister())
allows us to remove the synchronized_net() call from del_nbp()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Veaceslav Falico <vfalico@redhat.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VLAN is added to the port, a local fdb entry for that port
(the entry with the mac address of the port) is added for that
VLAN. This way we can correctly determine if the traffic
is for the bridge itself. If the address of the port changes,
we try to change all the local fdb entries we have for that port.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a netlink interface to add and remove vlan configuration on bridge port.
The interface uses the RTM_SETLINK message and encodes the vlan
configuration inside the IFLA_AF_SPEC. It is possble to include multiple
vlans to either add or remove in a single message.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds an optional infrustructure component to bridge that would allow
native vlan filtering in the bridge. Each bridge port (as well
as the bridge device) now get a VLAN bitmap. Each bit in the bitmap
is associated with a vlan id. This way if the bit corresponding to
the vid is set in the bitmap that the packet with vid is allowed to
enter and exit the port.
Write access the bitmap is protected by RTNL and read access
protected by RCU.
Vlan functionality is disabled by default.
Signed-off-by: Vlad Yasevich <vyasevic@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bridge link detection should follow the operational state
of the lower device, rather than the carrier bit. This allows devices
like tunnels that are controlled by userspace control plane to work
with bridge STP link management.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reviewed-by: Flavio Leitner <fbl@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When netdev_set_master faild in br_add_if, we should
call br_netpoll_disable to do some cleanup jobs,such
as free the memory of struct netpoll which allocated
in br_netpoll_enable.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Acked-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add comments on why we don't notify NETDEV_RELEASE.
Cc: David Miller <davem@davemloft.net>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ensures that bridges created with brctl(8) or ioctl(2) directly
also carry IFLA_LINKINFO when dumped over netlink. This also allows
to create a bridge with ioctl(2) and delete it with RTM_DELLINK.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
v2: add couple missing conversions in drivers
split unexporting netdev_fix_features()
implemented %pNF
convert sock::sk_route_(no?)caps
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Need to cleanup bridge device timers and ports when being bridge
device is being removed via netlink.
This fixes the problem of observed when doing:
ip link add br0 type bridge
ip link set dev eth1 master br0
ip link set br0 up
ip link del br0
which would cause br0 to hang in unregister_netdev because
of leftover reference count.
Reported-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When port is added to a bridge, the old code would send the new neighbor
netlink message before the subsequent new link message. This bug makes
it difficult to use the monitoring API in an application.
This code changes the ordering to add the forwarding entry
after the port is setup. One of the error checks (for invalid address)
is moved earlier in the process to avoid having to do unwind.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch does several things:
- introduces __ethtool_get_settings which is called from ethtool code and
from drivers as well. Put ASSERT_RTNL there.
- dev_ethtool_get_settings() is replaced by __ethtool_get_settings()
- changes calling in drivers so rtnl locking is respected. In
iboe_get_rate was previously ->get_settings() called unlocked. This
fixes it. Also prb_calc_retire_blk_tmo() in af_packet.c had the same
problem. Also fixed by calling __dev_get_by_index() instead of
dev_get_by_index() and holding rtnl_lock for both calls.
- introduces rtnl_lock in bnx2fc_vport_create() and fcoe_vport_create()
so bnx2fc_if_create() and fcoe_if_create() are called locked as they
are from other places.
- use __ethtool_get_settings() in bonding code
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
v2->v3:
-removed dev_ethtool_get_settings()
-added ASSERT_RTNL into __ethtool_get_settings()
-prb_calc_retire_blk_tmo - use __dev_get_by_index() and lock
around it and __ethtool_get_settings() call
v1->v2:
add missing export_symbol
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com> [except FCoE bits]
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since these checks and initialization are done in
dev_ethtool_get_settings called later on, remove this redundancy.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jan Beulich reported a possible net_device leak in bridge code after
commit bb900b27a2 (bridge: allow creating bridge devices with netlink)
Reported-by: Jan Beulich <JBeulich@novell.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ensures the neighbor entries associated with the bridge
dev are flushed, also invalidating the associated cached L2 headers.
This means we br_add_if/br_del_if ports to implement hand-over and
not wind up with bridge packets going out with stale MAC.
This means we can also change MAC of port device and also not wind
up with bridge packets going out with stale MAC.
This builds on Stephen Hemminger's patch, also handling the br_del_if
case and the port MAC change case.
Cc: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Andrei Warkentin <andreiw@motorola.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a new device is added to a bridge, the ethernet address of the
bridge network device may change. When the address changes, the
appropriate callback is called, but with the wrong device argument.
The address of the bridge device (ie br0) changes not the address
of the device being passed to add_if (ie eth0).
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the old days, we used to access dev->master in __netif_receive_skb()
in a rcu_read_lock section.
So one synchronize_net() call was needed in netdev_set_master() to make
sure another cpu could not use old master while/after we release it.
We now use netdev_rx_handler infrastructure and added one
synchronize_net() call in bond_release()/bond_release_all()
Remove the obsolete synchronize_net() from netdev_set_master() and add
one in bridge del_nbp() after its netdev_rx_handler_unregister() call.
This makes enslave -d a bit faster.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Jiri Pirko <jpirko@redhat.com>
CC: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the previous patch I added NETDEV_JOIN, now
we can notify netconsole when adding a device to a bridge too.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sure the ethtool's set_settings() callback of network
drivers don't ignore the 16 most significant bits when ethtool calls
their set_settings().
All drivers compiled with make allyesconfig on x86_64 have been
updated.
Signed-off-by: David Decotigny <decot@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Note: netdev_update_features() needs only rtnl_lock as br->port_list
is only changed while holding it.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add netlink device ops to allow creating bridge device via netlink.
This works in a manner similar to vlan, macvlan and bonding.
Example:
# ip link add link dev br0 type bridge
# ip link del dev br0
The change required rearranging initializtion code to deal with
being called by create link. Most of the initialization happens
in br_dev_setup, but allocation of stats is done in ndo_init callback
to deal with allocation failure. Sysfs setup has to wait until
after the network device kobject is registered.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mac address of the bridge device may be changed when a new interface
is added to the bridge. If this happens, then the bridge needs to call
the network notifiers to tickle any other systems that care. Since bridge
can be a module, this also means exporting the notifier function.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduce printk() levels to KERN_INFO in netdev_fix_features() as this will
be used by ethtool and might spam dmesg unnecessarily.
This converts the function to use netdev_info() instead of plain printk().
As a side effect, bonding and bridge devices will now log dropped features
on every slave device change.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Ben Hutchings: we presumably won't be defining features that
can only be enabled on 64-bit architectures.
Occurences found by `grep -r` on net/, drivers/net, include/
[ Move features and vlan_features next to each other in
struct netdev, as per Eric Dumazet's suggestion -DaveM ]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
br_port_get() renamed to br_port_get_rtnl() to make clear RTNL is held.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The macro br_port_exists() is not enough protection when only
RCU is being used. There is a tiny race where other CPU has cleared port
handler hook, but is bridge port flag might still be set.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If bridge port is offline, don't call ethtool to query speed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The carrier check is not called from work queue in current code.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register net_bridge_port pointer as rx_handler data pointer. As br_port is
removed from struct net_device, another netdev priv_flag is added to indicate
the device serves as a bridge port. Also rcuized pointers are now correctly
dereferenced in br_fdb.c and in netfilter parts.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add possibility to register rx_handler data pointer along with a rx_handler.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
