Send aligned pipe payload if requested to do so. Then, the socket buffer
needs not be fragmented anymore.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer Nokia cellular modems can use aligned payload for their GPRS pipe.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we have L3 tunnels with different inner/outer families
(i.e. IPV4/IPV6) which use a multicast address as the outer tunnel
destination address, multicast packets will be loopbacked back to the
sending socket even if IP*_MULTICAST_LOOP is set to disabled.
The mc_loop flag is present in the family specific part of the socket
(e.g. the IPv4 or IPv4 specific part). setsockopt sets the inner
family mc_loop flag. When the packet is pushed through the L3 tunnel
it will eventually be processed by the outer family which if different
will check the flag in a different part of the socket then it was set.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To make it easier to notice cases of calling sleeping ops in atomic context,
annotate driver-ops.h with appropiate might_sleep() calls. At the same time,
also document in mac80211.h the op functions with missing contexts.
mac80211 doesn't seem to use get_tx_stats anywhere currently. Just to be on
the safe side, I documented it to be atomic, but hopefully the op can be
removed in the future.
Compile-tested only.
Signed-off-by: Kalle Valo <kalle.valo@iki.fi>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All its members (vif, mac_addr, type) are now available
in the vif struct directly, so we can pass that instead
of the conf struct. I generated this patch (except the
mac80211 and header file changes) with this semantic
patch:
@@
identifier conf, fn, hw;
type tp;
@@
tp fn(struct ieee80211_hw *hw,
-struct ieee80211_if_init_conf *conf)
+struct ieee80211_vif *vif)
{
<...
(
-conf->type
+vif->type
|
-conf->mac_addr
+vif->addr
|
-conf->vif
+vif
)
...>
}
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When, for instance, a new IBSS peer is found, userspace
wants to be notified. Add events for all new stations
that mac80211 learns about.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add new commands for requesting the driver to remain awake
on a specified channel for the specified amount of time
(and another command to cancel such an operation). This
can be used to implement userspace-controlled off-channel
operations, like Public Action frame exchange on another
channel than the operation channel.
The off-channel operation should behave similarly to scan,
i.e. the local station (if associated) moves into power
save mode to request the AP to buffer frames for it and
then moves to the other channel to allow the off-channel
operation to be completed. The duration parameter can be
used to request enough time to receive a response from
the target station.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We've long lacked a good confirmation that frames
have really gone out, e.g. before going off-channel
for a scan. Add a flush() operation that drivers
can implement to provide that confirmation, and use
it in a few places:
* before scanning sends the nullfunc frames
* after scanning sends the nullfunc frames, if any
* when going idle, to send any pending frames
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This removes the remaining users of the rx status
'qual' field and the field itself.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For the cases where a lot of interfaces are used in conjunction with a
lot of LLC sockets bound to the same SAP, the iteration of the socket
list becomes prohibitively expensive.
Replacing the list with a a local address based hash significantly
improves the bind and listener lookup operations as well as the
datagram delivery.
Connected sockets delivery is also improved, but this patch does not
address the case where we have lots of sockets with the same local
address connected to different remote addresses.
In order to keep the socket sanity checks alive and fast a socket
counter was added to the SAP structure.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a per SAP device based hash table to solve the
multicast delivery scalability issue when we have large number of
interfaces and a large number of sockets bound to the same SAP.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For the reclamation phase we use the SLAB_DESTROY_BY_RCU mechanism,
which require some extra checks in the lookup code:
a) If the current socket was released, reallocated & inserted in
another list it will short circuit the iteration for the current list,
thus we need to restart the lookup.
b) If the current socket was released, reallocated & inserted in the
same list we just need to recheck it matches the look-up criteria and
if not we can skip to the next element.
In this case there is no need to restart the lookup, since sockets are
inserted at the start of the list and the worst that will happen is
that we will iterate throught some of the list elements more then
once.
Note that the /proc and multicast delivery was not yet converted to
RCU, it still uses spinlocks for protection.
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add rtnetlink init_rcvwnd to set the TCP initial receive window size
advertised by passive and active TCP connections.
The current Linux TCP implementation limits the advertised TCP initial
receive window to the one prescribed by slow start. For short lived
TCP connections used for transaction type of traffic (i.e. http
requests), bounding the advertised TCP initial receive window results
in increased latency to complete the transaction.
Support for setting initial congestion window is already supported
using rtnetlink init_cwnd, but the feature is useless without the
ability to set a larger TCP initial receive window.
The rtnetlink init_rcvwnd allows increasing the TCP initial receive
window, allowing TCP connection to advertise larger TCP receive window
than the ones bounded by slow start.
Signed-off-by: Laurent Chavey <chavey@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_push checks tcp_send_head and calls __tcp_push_pending_frames,
which again checks tcp_send_head, and this unnecessary check is
done for every other caller of __tcp_push_pending_frames.
Remove tcp_send_head check in __tcp_push_pending_frames and add
the check to tcp_push_pending_frames. Other functions call
__tcp_push_pending_frames only when tcp_send_head would evaluate
to true.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Enable spatial multiplexing in mac80211 by telling the
driver what to do and, where necessary, sending action
frames to the AP to update the requested SMPS mode.
Also includes a trivial implementation for hwsim that
just logs the requested mode.
For now, the userspace interface is in debugfs only,
and let you toggle the requested mode at any time.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the A-MSDU handling code from mac80211 to cfg80211 so that more
drivers can use it. The new created function ieee80211_amsdu_to_8023s
converts an A-MSDU frame to a list of 802.3 frames.
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For bluetooth 3, we will most likely not have
a netdev for a virtual interface (sdata), so
prepare for that by reducing the reliance on
having a netdev. This patch moves the name
and address fields into the sdata struct and
uses them from there all over. Some work is
needed to keep them sync'ed, but that's not
a lot of work and in slow paths anyway.
In doing so, this also reduces the number of
pointer dereferences in many places, because
of things like sdata->dev->dev_addr becoming
sdata->vif.addr.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (26 commits)
net: sh_eth alignment fix for sh7724 using NET_IP_ALIGN V2
ixgbe: allow tx of pre-formatted vlan tagged packets
ixgbe: Fix 82598 premature copper PHY link indicatation
ixgbe: Fix tx_restart_queue/non_eop_desc statistics counters
bcm63xx_enet: fix compilation failure after get_stats_count removal
packet: dont call sleeping functions while holding rcu_read_lock()
tcp: Revert per-route SACK/DSACK/TIMESTAMP changes.
ipvs: zero usvc and udest
netfilter: fix crashes in bridge netfilter caused by fragment jumps
ipv6: reassembly: use seperate reassembly queues for conntrack and local delivery
sky2: leave PCI config space writeable
sky2: print Optima chip name
x25: Update maintainer.
ipvs: fix synchronization on connection close
netfilter: xtables: document minimal required version
drivers/net/bonding/: : use pr_fmt
can: CAN_MCP251X should depend on HAS_DMA
drivers/net/usb: Correct code taking the size of a pointer
drivers/net/cpmac.c: Correct code taking the size of a pointer
drivers/net/sfc: Correct code taking the size of a pointer
...
It creates a regression, triggering badness for SYN_RECV
sockets, for example:
[19148.022102] Badness at net/ipv4/inet_connection_sock.c:293
[19148.022570] NIP: c02a0914 LR: c02a0904 CTR: 00000000
[19148.023035] REGS: eeecbd30 TRAP: 0700 Not tainted (2.6.32)
[19148.023496] MSR: 00029032 <EE,ME,CE,IR,DR> CR: 24002442 XER: 00000000
[19148.024012] TASK = eee9a820[1756] 'privoxy' THREAD: eeeca000
This is likely caused by the change in the 'estab' parameter
passed to tcp_parse_options() when invoked by the functions
in net/ipv4/tcp_minisocks.c
But even if that is fixed, the ->conn_request() changes made in
this patch series is fundamentally wrong. They try to use the
listening socket's 'dst' to probe the route settings. The
listening socket doesn't even have a route, and you can't
get the right route (the child request one) until much later
after we setup all of the state, and it must be done by hand.
This stuff really isn't ready, so the best thing to do is a
full revert. This reverts the following commits:
f55017a93f022c3f7d821aba721ebacda42ebd67345cda2fd6dc343475ed05eaade2786a2a2d6bf8
Signed-off-by: David S. Miller <davem@davemloft.net>
When fragments from bridge netfilter are passed to IPv4 or IPv6 conntrack
and a reassembly queue with the same fragment key already exists from
reassembling a similar packet received on a different device (f.i. with
multicasted fragments), the reassembled packet might continue on a different
codepath than where the head fragment originated. This can cause crashes
in bridge netfilter when a fragment received on a non-bridge device (and
thus with skb->nf_bridge == NULL) continues through the bridge netfilter
code.
Add a new reassembly identifier for packets originating from bridge
netfilter and use it to put those packets in insolated queues.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=14805
Reported-and-Tested-by: Chong Qiao <qiaochong@loongson.cn>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Currently the same reassembly queue might be used for packets reassembled
by conntrack in different positions in the stack (PREROUTING/LOCAL_OUT),
as well as local delivery. This can cause "packet jumps" when the fragment
completing a reassembled packet is queued from a different position in the
stack than the previous ones.
Add a "user" identifier to the reassembly queue key to seperate the queues
of each caller, similar to what we do for IPv4.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add a definition of the amount of TX headroom reserved by mac80211 itself
for its own purposes. Also add BUILD_BUG_ON to validate the value.
This define can then be used by drivers to request additional TX headroom
in the most efficient manner.
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
compat_sys_recvmmsg has a compat_timespec parameter and not a
timespec parameter. This way we also get rid of an odd cast.
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch moves retransmits_timed_out() from include/net/tcp.h
to tcp_timer.c, where it is used.
Reported-by: Frederic Leroy <fredo@starox.org>
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a problem in the TCP connection timeout calculation.
Currently, timeout decisions are made on the basis of the current
tcp_time_stamp and retrans_stamp, which is usually set at the first
retransmission.
However, if the retransmission fails in tcp_retransmit_skb(),
retrans_stamp is not updated and remains zero. This leads to wrong
decisions in retransmits_timed_out() if tcp_time_stamp is larger than
the specified timeout, which is very likely.
In this case, the TCP connection dies after the first attempted
(and unsuccessful) retransmission.
With this patch, tcp_skb_cb->when is used instead, when retrans_stamp
is not available.
This bug has been introduced together with retransmits_timed_out() in
2.6.32, as the number of retransmissions has been used for timeout
decisions before. The corresponding commit was
6fa12c8503 (Revert Backoff [v3]:
Calculate TCP's connection close threshold as a time value.).
Thanks to Ilpo Järvinen for code suggestions and Frederic Leroy for
testing.
Reported-by: Frederic Leroy <fredo@starox.org>
Signed-off-by: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we find a timewait connection in __inet_hash_connect() and reuse
it for a new connection request, we have a race window, releasing bind
list lock and reacquiring it in __inet_twsk_kill() to remove timewait
socket from list.
Another thread might find the timewait socket we already chose, leading to
list corruption and crashes.
Fix is to remove timewait socket from bind list before releasing the bind lock.
Note: This problem happens if sysctl_tcp_tw_reuse is set.
Reported-by: kapil dakhane <kdakhane@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First patch changes __inet_hash_nolisten() and __inet6_hash()
to get a timewait parameter to be able to unhash it from ehash
at same time the new socket is inserted in hash.
This makes sure timewait socket wont be found by a concurrent
writer in __inet_check_established()
Reported-by: kapil dakhane <kdakhane@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1815 commits)
mac80211: fix reorder buffer release
iwmc3200wifi: Enable wimax core through module parameter
iwmc3200wifi: Add wifi-wimax coexistence mode as a module parameter
iwmc3200wifi: Coex table command does not expect a response
iwmc3200wifi: Update wiwi priority table
iwlwifi: driver version track kernel version
iwlwifi: indicate uCode type when fail dump error/event log
iwl3945: remove duplicated event logging code
b43: fix two warnings
ipw2100: fix rebooting hang with driver loaded
cfg80211: indent regulatory messages with spaces
iwmc3200wifi: fix NULL pointer dereference in pmkid update
mac80211: Fix TX status reporting for injected data frames
ath9k: enable 2GHz band only if the device supports it
airo: Fix integer overflow warning
rt2x00: Fix padding bug on L2PAD devices.
WE: Fix set events not propagated
b43legacy: avoid PPC fault during resume
b43: avoid PPC fault during resume
tcp: fix a timewait refcnt race
...
Fix up conflicts due to sysctl cleanups (dead sysctl_check code and
CTL_UNNUMBERED removed) in
kernel/sysctl_check.c
net/ipv4/sysctl_net_ipv4.c
net/ipv6/addrconf.c
net/sctp/sysctl.c
* git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/sysctl-2.6: (43 commits)
security/tomoyo: Remove now unnecessary handling of security_sysctl.
security/tomoyo: Add a special case to handle accesses through the internal proc mount.
sysctl: Drop & in front of every proc_handler.
sysctl: Remove CTL_NONE and CTL_UNNUMBERED
sysctl: kill dead ctl_handler definitions.
sysctl: Remove the last of the generic binary sysctl support
sysctl net: Remove unused binary sysctl code
sysctl security/tomoyo: Don't look at ctl_name
sysctl arm: Remove binary sysctl support
sysctl x86: Remove dead binary sysctl support
sysctl sh: Remove dead binary sysctl support
sysctl powerpc: Remove dead binary sysctl support
sysctl ia64: Remove dead binary sysctl support
sysctl s390: Remove dead sysctl binary support
sysctl frv: Remove dead binary sysctl support
sysctl mips/lasat: Remove dead binary sysctl support
sysctl drivers: Remove dead binary sysctl support
sysctl crypto: Remove dead binary sysctl support
sysctl security/keys: Remove dead binary sysctl support
sysctl kernel: Remove binary sysctl logic
...
Its currently possible that several threads issuing a connect() find
the same timewait socket and try to reuse it, leading to list
corruptions.
Condition for bug is that these threads bound their socket on same
address/port of to-be-find timewait socket, and connected to same
target. (SO_REUSEADDR needed)
To fix this problem, we could unhash timewait socket while holding
ehash lock, to make sure lookups/changes will be serialized. Only
first thread finds the timewait socket, other ones find the
established socket and return an EADDRNOTAVAIL error.
This second version takes into account Evgeniy's review and makes sure
inet_twsk_put() is called outside of locked sections.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function walks the whole hashtable so there is no point in
passing it a network namespace. Instead I purge all timewait
sockets from dead network namespaces that I find. If the namespace
is one of the once I am trying to purge I am guaranteed no new timewait
sockets can be formed so this will get them all. If the namespace
is one I am not acting for it might form a few more but I will
call inet_twsk_purge again and shortly to get rid of them. In
any even if the network namespace is dead timewait sockets are
useless.
Move the calls of inet_twsk_purge into batch_exit routines so
that if I am killing a bunch of namespaces at once I will just
call inet_twsk_purge once and save a lot of redundant unnecessary
work.
My simple 4k network namespace exit test the cleanup time dropped from
roughly 8.2s to 1.6s. While the time spent running inet_twsk_purge fell
to about 2ms. 1ms for ipv4 and 1ms for ipv6.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Refactor the code so fib_rules_register always takes a template instead
of the actual fib_rules_ops structure that will be used. This is
required for network namespace support so 2 out of the 3 callers already
do this, it allows the error handling to be made common, and it allows
fib_rules_unregister to free the template for hte caller.
Modify fib_rules_unregister to use call_rcu instead of syncrhonize_rcu
to allw multiple namespaces to be cleaned up in the same rcu grace
period.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
