Proper machine resets via da9062/da9063 PMICs are very tricky as they
require special i2c atomic transfers when interrupts are not available
anymore. This is also a reason why both PMIC's restart handlers do not
use regmap but instead opt for i2c_smbus_write_byte_data() which does
i2c transfer in atomic manner. Under the hood, this function tries to
obtain i2c bus lock with call to i2c_adapter_trylock_bus() which will
return -EAGAIN (-11) if lock is not available.
Since commit 982bb70517 ("watchdog: reset last_hw_keepalive time at
start") occasional restart handler failures with "Failed to shutdown
(err = -11)" error messages were observed, indicating that some
process is holding the i2c bus lock. Investigation into the matter
uncovered that sometimes during reboot sequence watchdog ping is issued
late into poweroff/reboot phase which did not happen before mentioned
commit (usually the watchdog ping happened immediately as commit message
suggests). As of now, when watchdog ping usually happens late into
poweroff/reboot stage when interrupts are not available anymore, i2c bus
lock cannot be released anymore and pending restart handler in turn
fails.
Thus, to prevent such late watchdog pings from happening ahead of
pending machine restart and consequently locking up the i2c bus, check
for system_state in watchdog ping handler and consequently do not send
pings anymore in case system_state > SYSTEM_RUNNING.
Signed-off-by: Primoz Fiser <primoz.fiser@norik.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Link: https://lore.kernel.org/r/20210708082128.2832904-1-primoz.fiser@norik.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
While the driver will only match against a single device, convention is
to dynamically allocate the driver data.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1baffdc410d6476cccffe9712cec56350335812a.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Driver so far wasn't ported to the driver model and registered
the watchdog device out of the init after probing the I/O ports
for a watchdog with correct vendor and device revision.
Keep the device detection part at init time, but move watchdog
registration to a platform driver probe function.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/9e1088839662e5c357286cab0b9de0bb0602e4fd.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Migrating the driver lets us drop the watchdog misc device boilerplate
and reduces size by 285 lines. It also brings us support for new
functionality like CONFIG_WATCHDOG_HANDLE_BOOT_ENABLED.
This incurs a slight backwards-compatibility break, because the new
kernel watchdog API doesn't support unloading modules for drivers
whose watchdog hardware is reported to be running.
This means following scenario will be no longer supported:
- BIOS has enabled watchdog
- Module is loaded and unloaded without opening watchdog
- module_exit is expected to succeed and disable watchdog HW
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/35d9dbf57b58c5f003cef31dc256ec2fec044524.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Code for the common parts of the driver either uses watchdog_ as
prefix for the watchdog API or f71808e_ for everything else.
The driver now supports 9 more variants besides the f71808e,
so let's rename the common parts to start with fintek_wdt_ instead.
This makes code browsing easier, because it's readily apparent
that functions are not variant-specific. Some watchdog_-prefixed
functions remain, but these will be dropped altogether with the move
to the kernel watchdog API in a later commit.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/31805c6aeb8d161f852ddad7c32b91319f924988.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The fintek_wdt_names is meant for read-only use and is currently not
modified. Mark it const to catch future writes.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/9720c5a1efcef861da68b693453bb3eb3c21af37.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
max_timeout never served any purpose over WATCHDOG_MAX_TIMEOUT, which it
was initialized with. Drop it.
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/d1f8cda90283855633537adee0af2c6b00a9ec25.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The fintek watchdog timer can configure timeouts of second granularity
only up to 255 seconds. Beyond that, the timeout needs to be configured
with minute granularity. WDIOC_GETTIMEOUT should report the actual
timeout configured, not just echo back the timeout configured by the
user. Do so.
Fixes: 96cb4eb019 ("watchdog: f71808e_wdt: new watchdog driver for Fintek F71808E and F71882FG")
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Link: https://lore.kernel.org/r/5e17960fe8cc0e3cb2ba53de4730b75d9a0f33d5.1628525954.git-series.a.fatoum@pengutronix.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In the function stm32_iwdg_probe(), devm_platform_ioremap_resource
has already contained error message, so drop the redundant one.
Co-developed-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210814142741.7396-1-tangbin@cmss.chinamobile.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
TI's implementation does not service the watchdog even if the kernel
command line parameter omap_wdt.early_enable is set to 1. This patch
fixes the issue.
Signed-off-by: Walter Stoll <walter.stoll@duagon.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/88a8fe5229cd68fa0f1fd22f5d66666c1b7057a0.camel@duagon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210917092024.19323-1-krzysztof.kozlowski@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
SBSA says of the generic watchdog:
All registers are 32 bits in size and should be accessed using 32-bit
reads and writes. If an access size other than 32 bits is used then
the results are IMPLEMENTATION DEFINED.
and for qemu, the implementation will only allow 32-bit accesses
resulting in a synchronous external abort when configuring the watchdog.
Use lo_hi_* accessors rather than a readq/writeq.
Fixes: abd3ac7902 ("watchdog: sbsa: Support architecture version 1")
Signed-off-by: Jamie Iles <quic_jiles@quicinc.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/20210903112101.493552-1-quic_jiles@quicinc.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This reverts commit cb011044e3 ("watchdog: iTCO_wdt: Account for
rebooting on second timeout") and commit aec42642d9 ("watchdog: iTCO_wdt:
Fix detection of SMI-off case") since those patches cause a regression
on certain boards (https://bugzilla.kernel.org/show_bug.cgi?id=213809).
While this revert may result in some boards to only reset after twice
the configured timeout value, that is still better than a watchdog reset
after half the configured value.
Fixes: cb011044e3 ("watchdog: iTCO_wdt: Account for rebooting on second timeout")
Fixes: aec42642d9 ("watchdog: iTCO_wdt: Fix detection of SMI-off case")
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Mantas Mikulėnas <grawity@gmail.com>
Reported-by: Javier S. Pedro <debbugs@javispedro.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20211008003302.1461733-1-linux@roeck-us.net
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The DT binding includes for reset controllers are located in
include/dt-bindings/reset/. Move the Mediatek reset constants in there.
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Link: https://lore.kernel.org/r/20210930103105.v4.1.I514d9aafff3a062f751b37d3fea7402f67595b86@changeid
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
Compiling sb_watchdog needs to clearly define SIBYTE_HDR_FEATURES.
In arch/mips/sibyte/Platform like:
cflags-$(CONFIG_SIBYTE_BCM112X) += \
-I$(srctree)/arch/mips/include/asm/mach-sibyte \
-DSIBYTE_HDR_FEATURES=SIBYTE_HDR_FMASK_1250_112x_ALL
Otherwise, SIBYTE_HDR_FEATURES is SIBYTE_HDR_FMASK_ALL.
SIBYTE_HDR_FMASK_ALL is mean:
#define SIBYTE_HDR_FMASK_ALL SIBYTE_HDR_FMASK_1250_ALL | SIBYTE_HDR_FMASK_112x_ALL \
| SIBYTE_HDR_FMASK_1480_ALL)
So, If not limited to CPU_SB1, we will get such an error:
arch/mips/include/asm/sibyte/bcm1480_scd.h:261: error: "M_SPC_CFG_CLEAR" redefined [-Werror]
arch/mips/include/asm/sibyte/bcm1480_scd.h:262: error: "M_SPC_CFG_ENABLE" redefined [-Werror]
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Jackie Liu <liuyun01@kylinos.cn>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This rewrites the IXP4xx watchdog driver as follows:
- Spawn the watchdog driver as a platform device from the timer
driver. It's one device in the hardware, and the fact that
Linux splits the handling into two different devices is
a Linux pecularity, and thus it becomes a Linux pecularity
to spawn a separate watchdog driver.
- Spawn the watchdog driver from the timer driver at probe().
This is well after the timer driver as actually registered and
started and we know the register base is available.
- Instead of looping back callbacks to the timer drivers for all
watchdog calls, pass the register base to the watchdog driver
and manage the registers there. The two drivers aren't even
interested in the same register so the spinlock is totally
surplus, delete it.
- Replace pretty much all of the content in the watchdog driver
with a simple, modern watchdog driver utilizing the watchdog
core instead of registering its own misc device and ioctl()
handling.
- Drop module parameters as the same already exist in the
watchdog core.
What remains is a slim elegant (IMO) watchdog driver using the
watchdog core, spawning from device tree or boardfile alike.
Cc: Daniel Lezcano <daniel.lezcano@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20210726121214.2572836-1-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
We must not pet a running watchdog when handle_boot_enabled is off
because this will kick off automatic triggering before userland is
running, defeating the purpose of the handle_boot_enabled control.
Furthermore, don't ping in case watchdog_set_last_hw_keepalive was
called incorrectly when the hardware watchdog is actually not running.
Fixed: cef9572e9a ("watchdog: add support for adjusting last known HW keepalive time")
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/93d56386-6e37-060b-55ce-84de8cde535f@web.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This adds device tree probing to the MAX63xx driver so it can be
instantiated from the device tree. We use the generic fwnode-based
method to get to the match data and clean up by constifying the
functions as the match is indeed a const.
Cc: Marc Zyngier <maz@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210714153314.1004147-2-linus.walleij@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The struct tqmx86_wdt_ops is only assigned to the ops pointer in the
watchdog_device struct, which is a pointer to const struct watchdog_ops.
Make it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210727223042.48150-3-rikard.falkeborn@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The struct mpc8xxx_wdt_ops is only assigned to the ops pointer in the
watchdog_device struct, which is a pointer to const struct watchdog_ops.
Make it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210727223042.48150-4-rikard.falkeborn@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The struct sl28cpld_wdt_ops is only assigned to the ops pointer in the
watchdog_device struct, which is a pointer to const struct watchdog_ops.
Make it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210727223042.48150-2-rikard.falkeborn@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Obviously, the test needs to run against the register content, not its
address.
Fixes: cb011044e3 ("watchdog: iTCO_wdt: Account for rebooting on second timeout")
Cc: stable@vger.kernel.org
Reported-by: Mantas Mikulėnas <grawity@gmail.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Paolo Bonzini <pbonzini@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Mantas Mikulėnas <grawity@gmail.com>
Link: https://lore.kernel.org/r/d84f8e06-f646-8b43-d063-fb11f4827044@siemens.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Until now all Raspberry Pi boards used the power off function of the SoC.
But the Raspberry Pi 400 uses gpio-poweroff for the whole board which
possibly cannot register the poweroff handler because the it's
already registered by this watchdog driver. So consider the
system-power-controller property for registering, which is already
defined in soc/bcm/brcm,bcm2835-pm.txt .
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Nicolas Saenz Julienne <nsaenz@kernel.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1622981777-5023-3-git-send-email-stefan.wahren@i2se.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Suspend routine disables wdog clk. Nevertheless, the watchdog subsystem
is not aware of that and can still try to ping wdog through
watchdog_ping_work. In order to prevent such condition and therefore
prevent from system hang (caused by the wdog register access issued
while the wdog clock is disabled) notify watchdog core that the ping
worker should be canceled during watchdog core suspend and restored
during resume.
Signed-off-by: Michal Koziel <michal.koziel@emlogic.no>
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210618195033.3209598-3-grzegorz.jaszczyk@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The watchdog drivers often disable wdog clock during suspend and then
enable it again during resume. Nevertheless the ping worker is still
running and can issue low-level ping while the wdog clock is disabled
causing the system hang. To prevent such condition register pm notifier
in the watchdog core which will call watchdog_dev_suspend/resume and
actually cancel ping worker during suspend and restore it back, if
needed, during resume.
Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210618195033.3209598-2-grzegorz.jaszczyk@linaro.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
watchdog_hrtimer_pretimeout_stop needs the watchdog device to have a
valid pointer to the watchdog core data to stop the pretimeout hrtimer.
Therefore it needs to be called before the pointers are cleared in
watchdog_cdev_unregister.
Fixes: 7b7d2fdc8c ("watchdog: Add hrtimer-based pretimeout feature")
Reported-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1624429583-5720-1-git-send-email-curtis.klein@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Some watchdog devices might conditionally support pretimeouts (e.g. if
an interrupt is exposed for the device) but some watchdog drivers might
still define the set_pretimeout operation (e.g. the mtk_wdt driver) and
indicate support at runtime through the WDIOF_PRETIMEOUT flag. If the
kernel is compiled with CONFIG_WATCHDOG_HRTIMER_PRETIMEOUT enabled,
watchdog_set_pretimeout would run the driver specific set_pretimeout
even if WDIOF_PRETIMEOUT is not set which might have unintended
consequences.
So this change checks that the device flags and only runs the driver
operation if pretimeouts are supported.
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1624751265-24785-1-git-send-email-curtis.klein@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The only known BD70528 use-cases are such that the PMIC is controlled
from separate MCU which is not running Linux. I am not aware of
any Linux driver users. Furthermore, it seems there is no demand for
this IC. Let's ease the maintenance burden and drop the driver. We can
always add it back if there is sudden need for it.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/994d2e374262c3f59f4465c03ef23d3116120778.1621937490.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanna driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems mushed
together" tree...
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYOM8jQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymECgCg0yL+8WxDKO5Gg5llM5PshvLB1rQAn0y5pDgg
nw78LV3HQ0U7qaZBtI91
=x+AR
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here is the big set of char / misc and other driver subsystem updates
for 5.14-rc1. Included in here are:
- habanalabs driver updates
- fsl-mc driver updates
- comedi driver updates
- fpga driver updates
- extcon driver updates
- interconnect driver updates
- mei driver updates
- nvmem driver updates
- phy driver updates
- pnp driver updates
- soundwire driver updates
- lots of other tiny driver updates for char and misc drivers
This is looking more and more like the "various driver subsystems
mushed together" tree...
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (292 commits)
mcb: Use DEFINE_RES_MEM() helper macro and fix the end address
PNP: moved EXPORT_SYMBOL so that it immediately followed its function/variable
bus: mhi: pci-generic: Add missing 'pci_disable_pcie_error_reporting()' calls
bus: mhi: Wait for M2 state during system resume
bus: mhi: core: Fix power down latency
intel_th: Wait until port is in reset before programming it
intel_th: msu: Make contiguous buffers uncached
intel_th: Remove an unused exit point from intel_th_remove()
stm class: Spelling fix
nitro_enclaves: Set Bus Master for the NE PCI device
misc: ibmasm: Modify matricies to matrices
misc: vmw_vmci: return the correct errno code
siox: Simplify error handling via dev_err_probe()
fpga: machxo2-spi: Address warning about unused variable
lkdtm/heap: Add init_on_alloc tests
selftests/lkdtm: Enable various testable CONFIGs
lkdtm: Add CONFIG hints in errors where possible
lkdtm: Enable DOUBLE_FAULT on all architectures
lkdtm/heap: Add vmalloc linear overflow test
lkdtm/bugs: XFAIL UNALIGNED_LOAD_STORE_WRITE
...
Core changes:
- Cleanup and simplification of common code to invoke the low level
interrupt flow handlers when this invocation requires irqdomain
resolution. Add the necessary core infrastructure.
- Provide a proper interface for modular PMU drivers to set the
interrupt affinity.
- Add a request flag which allows to exclude interrupts from spurious
interrupt detection. Useful especially for IPI handlers which always
return IRQ_HANDLED which turns the spurious interrupt detection into a
pointless waste of CPU cycles.
Driver changes:
- Bulk convert interrupt chip drivers to the new irqdomain low level flow
handler invocation mechanism.
- Add device tree bindings for the Renesas R-Car M3-W+ SoC
- Enable modular build of the Qualcomm PDC driver
- The usual small fixes and improvements.
-----BEGIN PGP SIGNATURE-----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=FIKh
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2021-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core changes:
- Cleanup and simplification of common code to invoke the low level
interrupt flow handlers when this invocation requires irqdomain
resolution. Add the necessary core infrastructure.
- Provide a proper interface for modular PMU drivers to set the
interrupt affinity.
- Add a request flag which allows to exclude interrupts from spurious
interrupt detection. Useful especially for IPI handlers which
always return IRQ_HANDLED which turns the spurious interrupt
detection into a pointless waste of CPU cycles.
Driver changes:
- Bulk convert interrupt chip drivers to the new irqdomain low level
flow handler invocation mechanism.
- Add device tree bindings for the Renesas R-Car M3-W+ SoC
- Enable modular build of the Qualcomm PDC driver
- The usual small fixes and improvements"
* tag 'irq-core-2021-06-29' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (38 commits)
dt-bindings: interrupt-controller: arm,gic-v3: Describe GICv3 optional properties
irqchip: gic-pm: Remove redundant error log of clock bulk
irqchip/sun4i: Remove unnecessary oom message
irqchip/irq-imx-gpcv2: Remove unnecessary oom message
irqchip/imgpdc: Remove unnecessary oom message
irqchip/gic-v3-its: Remove unnecessary oom message
irqchip/gic-v2m: Remove unnecessary oom message
irqchip/exynos-combiner: Remove unnecessary oom message
irqchip: Bulk conversion to generic_handle_domain_irq()
genirq: Move non-irqdomain handle_domain_irq() handling into ARM's handle_IRQ()
genirq: Add generic_handle_domain_irq() helper
irqchip/nvic: Convert from handle_IRQ() to handle_domain_irq()
irqdesc: Fix __handle_domain_irq() comment
genirq: Use irq_resolve_mapping() to implement __handle_domain_irq() and co
irqdomain: Introduce irq_resolve_mapping()
irqdomain: Protect the linear revmap with RCU
irqdomain: Cache irq_data instead of a virq number in the revmap
irqdomain: Use struct_size() helper when allocating irqdomain
irqdomain: Make normal and nomap irqdomains exclusive
powerpc: Move the use of irq_domain_add_nomap() behind a config option
...
Over time the functions were renamed,
but this was not always reflected in kdoc, fix that.
Signed-off-by: Tamar Mashiah <tamar.mashiah@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Link: https://lore.kernel.org/r/20210621193756.134027-1-tomas.winkler@intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use dev_err() instead of pr_err(), so device name is also shown in the log.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210616181708.19530-2-info@metux.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
It adds a driver for the IP block handling the watchdog timer found for
Mstar MSC313e SoCs and newer.
Signed-off-by: Daniel Palmer <daniel@0x0f.com>
Co-developed-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210611200801.52139-3-romain.perier@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This was already attempted to fix via 1fccb73011: If the BIOS did not
enable TCO SMIs, the timer definitely needs to trigger twice in order to
cause a reboot. If TCO SMIs are on, as well as SMIs in general, we can
continue to assume that the BIOS will perform a reboot on the first
timeout.
QEMU with its ICH9 and related BIOS falls into the former category,
currently taking twice the configured timeout in order to reboot the
machine. For iTCO version that fall under turn_SMI_watchdog_clear_off,
this is also true and was currently only addressed for v1, irrespective
of the turn_SMI_watchdog_clear_off value.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/0b8bb307-d08b-41b5-696c-305cdac6789c@siemens.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Add support for compatible sama7g5-wdt.
The sama7g5 wdt is the same hardware block as on sam9x60.
Adapt the driver to use the sam9x60/sama7g5 variant if either
of the two compatibles are selected (sam9x60-wdt/sama7g5-wdt).
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210527100120.266796-2-eugen.hristev@microchip.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Remove the ZIIRAVE_{BL,FW}_VERION_FMT defines since they're only used in
very few places. While at it, add newlines to sysfs outputs.
Suggested-By: Joe Perches <joe@perches.com>
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210520072918.76482-1-juergh@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
If the WDIOF_PRETIMEOUT flag is not set when registering the device the
driver will not show the sysfs entries or register the default governor.
By moving the registering after the decision whether pretimeout is
supported this gets fixed.
Signed-off-by: Stefan Eichenberger <eichest@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20210519080311.142928-1-eichest@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The assign for 'ret' is redundant and can be removed,
because it will be assigned before use.
Signed-off-by: Junlin Yang <yangjunlin@yulong.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210203122404.752-1-angkery@163.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This adds the option to use a hrtimer to generate a watchdog pretimeout
event for hardware watchdogs that do not natively support watchdog
pretimeouts.
With this enabled, all watchdogs will appear to have pretimeout support
in userspace. If no pretimeout value is set, there will be no change in
the watchdog's behavior. If a pretimeout value is set for a specific
watchdog that does not have built-in pretimeout support, a timer will be
started that should fire at the specified time before the watchdog
timeout would occur. When the watchdog is successfully pinged, the timer
will be restarted. If the timer is allowed to fire it will generate a
pretimeout event. However because a software timer is used, it may not
be able to fire in every circumstance.
If the watchdog does support a pretimeout natively, that functionality
will be used instead of the hrtimer.
The general design of this feaure was inspired by the software watchdog,
specifically its own pretimeout implementation. However the software
watchdog and this feature are completely independent. They can be used
together; with or without CONFIG_SOFT_WATCHDOG_PRETIMEOUT enabled.
The main advantage of using the hrtimer pretimeout with a hardware
watchdog, compared to running the software watchdog with a hardware
watchdog, is that if the hardware watchdog driver is unable to ping the
watchdog (e.g. due to a bus or communication error), then the hrtimer
pretimeout would still fire whereas the software watchdog would not.
Signed-off-by: Curtis Klein <curtis.klein@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1612383090-27110-1-git-send-email-curtis.klein@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
During suspend/resume usecases and tests, it is common to see issues
such as lockups either in suspend path or resume path because of the
bugs in the corresponding device driver pm handling code. In such cases,
it is important that watchdog is active to make sure that we either
receive a watchdog pretimeout notification or a bite causing reset
instead of a hang causing us to hard reset the machine.
There are good reasons as to why we need this because:
* We can have a watchdog pretimeout governor set to panic in which
case we can have a backtrace which would help identify the issue
with the particular driver and cause a normal reboot.
* Even in case where there is no pretimeout support, a watchdog
bite is still useful because some firmware has debug support to dump
CPU core context on watchdog bite for post-mortem analysis.
* One more usecase which comes to mind is of warm reboot. In case we
hard reset the target, a cold reboot could be induced resulting in
lose of ddr contents thereby losing all the debug info.
Currently, the watchdog pm callback just invokes the usual suspend
and resume callback which do not have any special ordering in the
sense that a watchdog can be suspended before the buggy device driver
suspend callback and watchdog resume can happen after the buggy device
driver resume callback. This would mean that the watchdog will not be
active when the buggy driver cause the lockups thereby hanging the
system. So to make sure this doesn't happen, move the watchdog pm to
use late/early system pm callbacks which will ensure that the watchdog
is suspended late and resumed early so that it can catch such issues.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20210310202004.1436-1-saiprakash.ranjan@codeaurora.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In case of error, the function device_node_to_regmap() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Fixes: 6d532143c9 ("watchdog: jz4740: Use regmap provided by TCU driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20210304045909.945799-1-weiyongjun1@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the bark interrupt as the pretimeout notifier if available.
When the watchdog timer expires in dual mode, an interrupt will be
triggered first, then the timing restarts. The reset signal will be
initiated when the timer expires again.
The pretimeout notification shall occur at timeout-sec/2.
V2:
- panic() by default if WATCHDOG_PRETIMEOUT_GOV is not enabled.
V3:
- Modify the pretimeout behavior, manually reset after the pretimeout
- is processed and wait until timeout.
V4:
- Remove pretimeout related processing.
- Add dual mode control separately.
V5:
- Fix some formatting and printing problems.
V6:
- Realize pretimeout processing through dualmode.
V7:
- Add set_pretimeout().
V8/V9:
- Fix some formatting problems.
Signed-off-by: Wang Qing <wangqing@vivo.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1619315527-8171-2-git-send-email-wangqing@vivo.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The command 'find drivers/watchdog | xargs ./scripts/kernel-doc -none'
reports a number of kernel-doc warnings in the watchdog subsystem.
Address the kernel-doc warnings that were purely syntactic issues with
kernel-doc comments.
The remaining kernel-doc warnings are of type "Excess function parameter"
and "Function parameter or member not described". These warnings would
need to be addressed in a second pass with a bit more insight into the
APIs and purpose of the functions in the watchdog subsystem.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210322065337.617-1-lukas.bulwahn@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
"%p" is not printing the pointer value.
In driver, printing pointer value is not useful so avoiding print.
iSigned-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210329161939.37680-6-srinivas.neeli@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
clk is an optional property, if clock not defined,
calling clk_prepare_enable() and devm_add_action_or_reset()
are not useful.
so calling these two apis only when clock is present.
Addresses-Coverity:"FORWARD_NULL"
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210329161939.37680-5-srinivas.neeli@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This patch removes pr_info in stop function and adds dev_dbg()
in start/stop function to display device specific debug info.
Signed-off-by: Srinivas Goud <srinivas.goud@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210329161939.37680-4-srinivas.neeli@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Based on checkpatch every spinlock should be documented.
The patch is fixing this issue:
./scripts/checkpatch.pl --strict -f drivers/watchdog/of_xilinx_wdt.c
CHECK: spinlock_t definition without comment
+ spinlock_t spinlock;
Signed-off-by: Srinivas Goud <srinivas.goud@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Srinivas Neeli <srinivas.neeli@xilinx.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210329161939.37680-2-srinivas.neeli@xilinx.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Use the device_get_match_data() helper instead of open coding.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1617243921-56774-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Fix hardware timeout calculation in aspeed_wdt_set_timeout function to
ensure the reload value does not exceed the hardware limit.
Fixes: efa859f7d7 ("watchdog: Add Aspeed watchdog driver")
Reported-by: Amithash Prasad <amithash@fb.com>
Signed-off-by: Tao Ren <rentao.bupt@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210417034249.5978-1-rentao.bupt@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Change a non-working ftp: URL to https:.
Wrap long lines earlier.
Spell "IP" with capital letters.
Change "it`s" to "it's". The backtick (grave accent) is not an apostrophe.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210419000704.17745-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Convert sprintf() in sysfs "show" functions to sysfs_emit() and
sysfs_emit_at() in order to check for buffer overruns in sysfs outputs.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210511061812.480172-1-juergh@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This driver's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/r/1620802676-19701-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1620716691-108460-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The valid range for the 'timeout' value is useful information so expose
the min and max timeout values via sysfs.
Signed-off-by: Juerg Haefliger <juergh@canonical.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210511062953.485252-1-juergh@canonical.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Kernel doc validation script is not happy
CHECK .../sp805_wdt.c
.../sp805_wdt.c:73: warning: Function parameter or member 'rate' not described in 'sp805_wdt'
Fix this by describing rate parameter.
While at it, mark clk one optional.
Fixes: dc0e4a3bb7 ("watchdog: sp805: Add clock-frequency property")
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210517174912.26419-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Replace open coded variants of devm_clk_get_optional().
While at it, drop unneeded OF and ACPI dependency as the APIs in use
are provider agnostic.
Cc: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Link: https://lore.kernel.org/r/20210517174456.22050-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
New hardware with new PCI ID info.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1620878612-24736-2-git-send-email-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Clean up the following includecheck warning:
./drivers/watchdog/dw_wdt.c: linux/kernel.h is included more than once.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1620904182-74107-1-git-send-email-jiapeng.chong@linux.alibaba.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This module's remove path calls del_timer(). However, that function
does not wait until the timer handler finishes. This means that the
timer handler may still be running after the driver's remove function
has finished, which would result in a use-after-free.
Fix by calling del_timer_sync(), which makes sure the timer handler
has finished, and unable to re-schedule itself.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1620716495-108352-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Since watchdog_ping_work is not freezable so that it maybe scheduled before
imx2_wdt_resume where watchdog clock enabled, hence, kernel will hang in
imx2_wdt_ping without clock, and then watchdog reset happen. Add clk_is_on
to prevent the above case by ignoring ping until watchdog driver resume
back indeed.
Signed-off-by: Robin Gong <yibin.gong@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1621012875-22667-1-git-send-email-yibin.gong@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The mtx-1_wdt driver does not need the au1000.h header file.
Instead, the header file causes build errors, so drop it.
This change fixes multiple build errors, all in au1000.h. E.g.:
In file included from ../drivers/watchdog/mtx-1_wdt.c:44:
../arch/mips/include/asm/mach-au1x00/au1000.h: In function 'alchemy_rdsys':
../arch/mips/include/asm/mach-au1x00/au1000.h:603:36: error: implicit declaration of function 'KSEG1ADDR'; did you mean 'CKSEG1ADDR'? [-Werror=implicit-function-declaration]
603 | void __iomem *b = (void __iomem *)KSEG1ADDR(AU1000_SYS_PHYS_ADDR);
../arch/mips/include/asm/mach-au1x00/au1000.h:603:20: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
603 | void __iomem *b = (void __iomem *)KSEG1ADDR(AU1000_SYS_PHYS_ADDR);
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: linux-watchdog@vger.kernel.org
Cc: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210516211703.25349-1-rdunlap@infradead.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
For Armv8.6, The frequency of CNTFRQ_EL0 is standardized to a
frequency of 1GHz, so Arm Base System Architecture 1.0[1] has
introduced watchdog revision 1 that increases the length the
watchdog offset register to 48 bit, while other operation of
the watchdog remains the same.
The driver can determine which version of the watchdog is
implemented through the watchdog interface identification
register (W_IID). If the version is 0x1, the watchdog
offset register will be 48 bit, otherwise it will be 32 bit.
[1] https://developer.arm.com/documentation/den0094/latest
Cc: Wim Van Sebroeck <wim@linux-watchdog.org>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Suravee Suthikulpanit <Suravee.Suthikulpanit@amd.com>
Cc: Al Stone <al.stone@linaro.org>
Cc: Jianchao Hu <hujianchao@hisilicon.com>
Cc: Huiqiang Wang <wanghuiqiang@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1621253408-23401-1-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Updated the WDT SMC handler MACRO name to make it clear that its
a ARM SMC handler that helps in clearing the WDT interrupt bit.
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Kris Pan <kris.pan@intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20210517174953.19404-9-shruthi.sanil@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In the TO ISR removed updating the Timeout value because
its not serving any purpose as the timer would have already expired
and the system would be rebooting.
Fixes: fa0f8d51e9 ("watchdog: Add watchdog driver for Intel Keembay Soc")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kris Pan <kris.pan@intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20210517174953.19404-7-shruthi.sanil@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Removed set timeout from the start WDT function. There is a function
defined to set the timeout. Hence no need to set the timeout again in
start function as the timeout would have been already updated
before calling the start/enable.
Fixes: fa0f8d51e9 ("watchdog: Add watchdog driver for Intel Keembay Soc")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kris Pan <kris.pan@intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20210517174953.19404-6-shruthi.sanil@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
During the interrupt service routine of the TimeOut interrupt and
the ThresHold interrupt, the respective interrupt clear bit
have to be cleared and not both.
Fixes: fa0f8d51e9 ("watchdog: Add watchdog driver for Intel Keembay Soc")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kris Pan <kris.pan@intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20210517174953.19404-5-shruthi.sanil@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The pretimeout has to be updated to zero during the ISR of the
ThresHold interrupt. Else the TH interrupt would be triggerred for
every tick until the timeout.
Fixes: fa0f8d51e9 ("watchdog: Add watchdog driver for Intel Keembay Soc")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kris Pan <kris.pan@intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20210517174953.19404-4-shruthi.sanil@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The pre-timeout value to be programmed to the register has to be
calculated and updated for every change in the timeout value.
Else the threshold time wouldn't be calculated to its
corresponding timeout.
Fixes: fa0f8d51e9 ("watchdog: Add watchdog driver for Intel Keembay Soc")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kris Pan <kris.pan@intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20210517174953.19404-3-shruthi.sanil@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The pretimeout register has a default reset value. Hence
when a smaller WDT timeout is set which would be lesser than the
default pretimeout, the system behaves abnormally, starts
triggering the pretimeout interrupt even when the WDT is
not enabled, most of the times leading to system crash.
Hence an update in the pre-timeout is also required for the
default timeout that is being configured.
Fixes: fa0f8d51e9 ("watchdog: Add watchdog driver for Intel Keembay Soc")
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Kris Pan <kris.pan@intel.com>
Signed-off-by: Shruthi Sanil <shruthi.sanil@intel.com>
Link: https://lore.kernel.org/r/20210517174953.19404-2-shruthi.sanil@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
This drivers currently obtains linux/irqdomain.h by luck and
a chain of bizarre inclusions, which we're about to fix.
Let's include the required file directly.
Signed-off-by: Marc Zyngier <maz@kernel.org>
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a fallthrough pseudo-keyword instead of letting the
code fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
- New Drivers
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
- New Device Support
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
- Removed Device Support
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
- New Functionality
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
- New/converted Device Tree bindings; rohm,bd71815-pmic, rohm,bd9576-pmic,
netronix,ntxec, actions,atc260x,
ricoh,rn5t618, qcom-pm8xxx
- Fix-ups
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618, max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci,
atc260x-i2c, intel_quark_i2c_gpio
- Bug Fixes
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers
-----BEGIN PGP SIGNATURE-----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=IJSL
-----END PGP SIGNATURE-----
Merge tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"Core Framework:
- Add support for Software Nodes to MFD Core
- Remove support for Device Properties from MFD Core
- Use standard APIs in MFD Core
New Drivers:
- Add support for ROHM BD9576MUF and BD9573MUF PMICs
- Add support for Netronix Embedded Controller, PWM and RTC
- Add support for Actions Semi ATC260x PMICs and OnKey
New Device Support:
- Add support for DG1 PCIe Graphics Card to Intel PMT
- Add support for ROHM BD71815 PMIC to ROHM BD71828
- Add support for Tolino Shine 2 HD to Netronix Embedded Controller
- Add support for AX10 BMC Secure Updates to Intel M10 BMC
Removed Device Support:
- Remove Arizona Extcon support from MFD
- Remove ST-E AB8500 Power Supply code from MFD
- Remove AB3100 altogether
New Functionality:
- Add support for SMBus and I2C modes to Dialog DA9063
- Switch to using Software Nodes in Intel (various)
New/converted Device Tree bindings:
- rohm bd71815-pmic, rohm bd9576-pmic, netronix ntxec, actions
atc260x, ricoh rn5t618, qcom pm8xxx
- Fix-ups:
- Fix error handling/path; intel_pmt
- Simplify code; rohm-bd718x7, ab8500-core, intel-m10-bmc
- Trivial clean-ups (reordering, spelling); rohm-generic, rn5t618,
max8997
- Use correct data-type; db8500-prcmu
- Remove superfluous code; lp87565, intel_quark_i2c_gpi, lpc_sch, twl
- Use generic APIs/defines; lm3533-core, intel_quark_i2c_gpio
- Regmap related fix-ups; intel-m10-bmc, sec-core
- Reorder resource freeing during remove; intel_quark_i2c_gpio
- Make table indexing more robust; intel_quark_i2c_gpio
- Fix reference imbalances; arizona-irq
- Staticify and (un)constify things; arizona-spi, stmpe, ene-kb3930,
intel-lpss-acpi, intel-lpss-pci, atc260x-i2c, intel_quark_i2c_gpio
Bug Fixes:
- Fix incorrect (register) values; intel-m10-bmc
- Kconfig related fixes; ABX500_CORE
- Do not clear the Auto Reload Register; stm32-timers"
* tag 'mfd-next-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (84 commits)
mfd: intel-m10-bmc: Add support for MAX10 BMC Secure Updates
Revert "mfd: max8997: Add of_compatible to Extcon and Charger mfd_cell"
mfd: twl: Remove unused inline function twl4030charger_usb_en()
dt-bindings: mfd: Convert pm8xxx bindings to yaml
dt-bindings: mfd: Add compatible for pmk8350 rtc
i2c: designware: Get rid of legacy platform data
mfd: intel_quark_i2c_gpio: Convert I²C to use software nodes
mfd: lpc_sch: Partially revert "Add support for Intel Quark X1000"
mfd: arizona: Fix rumtime PM imbalance on error
mfd: max8997: Replace 8998 with 8997
mfd: core: Use acpi_find_child_device() for child devices lookup
mfd: intel_quark_i2c_gpio: Don't play dirty trick with const
mfd: intel_quark_i2c_gpio: Enable MSI interrupt
mfd: intel_quark_i2c_gpio: Reuse BAR definitions for MFD cell indexing
mfd: ntxec: Support for EC in Tolino Shine 2 HD
mfd: stm32-timers: Avoid clearing auto reload register
mfd: intel_quark_i2c_gpio: Replace I²C speeds with descriptive definitions
mfd: intel_quark_i2c_gpio: Remove unused struct device member
mfd: intel_quark_i2c_gpio: Unregister resources in reversed order
mfd: Kconfig: ABX500_CORE should depend on ARCH_U8500
...
The Nuvoton WPCM450 BMC is an older chip based on the ARM926 CPU core
that remains in use on Supermicro X9 server boards among others. Support
gets added for a particular server board using this SoC along with the
basic platform bringup.
As the platform is a predecessor to the npcm7xx platform we already
support, it is added to the same directory, despite using a different
name. It also seems to be related to the older w90x900/nuc9xx platform
that was removed last year.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=8lh7
-----END PGP SIGNATURE-----
Merge tag 'arm-newsoc-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM Nuvoton WPCM450 platform support from Arnd Bergmann:
"The Nuvoton WPCM450 BMC is an older chip based on the ARM926 CPU core
that remains in use on Supermicro X9 server boards among others.
Support gets added for a particular server board using this SoC along
with the basic platform bringup.
As the platform is a predecessor to the npcm7xx platform we already
support, it is added to the same directory, despite using a different
name. It also seems to be related to the older w90x900/nuc9xx platform
that was removed last year"
* tag 'arm-newsoc-5.13' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
ARM: config: Add WPCM to multi v5
MAINTAINERS: Add entry for Nuvoton WPCM450
ARM: dts: Add devicetree for Supermicro X9SCi-LN4F based on WPCM450
ARM: dts: Add devicetree for Nuvoton WPCM450 BMC chip
watchdog: npcm: Add support for WPCM450
ARM: npcm: Introduce Nuvoton WPCM450 SoC
dt-bindings: watchdog: npcm: Add nuvoton,wpcm450-wdt
dt-bindings: arm: npcm: Add nuvoton,wpcm450 compatible string
dt-bindings: vendor-prefixes: Add Supermicro
ARM: dts: Add board-specific compatible string to npcm750-evb devicetree
dt-bindings: arm: Convert nuvoton,npcm750 binding to YAML
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAmBzdS0eHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGDdAIAIpKH/tAHhH7s7QH
m5ewgE8foP7M5Ue9fp3+JmbtaYSzhCAMcKhqGtat/zk5PvA9AoYCDXrTetfYtBHh
LUOmhL9hcKItNobfkYBok6BiFjGUEL3HMqz5w+MUsMwnXIc4RXqfJmsQ932z9Kxf
yDwe6ehIzJVrQLI/C0mTamYRHu2aiZ1VWzhKuT493rLeg0R2odCCIClPN+/QvCwb
8/sk6l1c8eOUYYMUzKFZifaZGb12qDjRt4pZmk51aMTzg0WCpElJG+7Uqr4QQhZP
p6xeNuUQq6WwxtlDkmo79Uzkrurb5tN2/hZ1RcJhs3EdHfpR0MjIyH3Znnb31gnu
39VjHhg=
=4KP/
-----END PGP SIGNATURE-----
Merge tag 'v5.12-rc7' into driver-core-next
We need the driver core fix in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change my e-mail address to kabel@kernel.org, and fix my name in
non-code parts (add diacritical mark).
Link: https://lkml.kernel.org/r/20210325171123.28093-2-kabel@kernel.org
Signed-off-by: Marek Behún <kabel@kernel.org>
Cc: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jassi Brar <jassisinghbrar@gmail.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a compatible string for WPCM450, which has essentially the same
watchdog mechanism as NPCM750.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20210406120921.2484986-8-j.neuschaefer@gmx.net
Signed-off-by: Joel Stanley <joel@jms.id.au>
Few drivers implement remove call-back only for ensuring a delayed
work gets cancelled prior driver removal. Clean-up these by switching
to use devm_delayed_work_autocancel() instead.
This change is compile-tested only. All testing is appreciated.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Link: https://lore.kernel.org/r/be299515fbee2c311162ca99ea0dbee933044b56.1616506559.git.matti.vaittinen@fi.rohmeurope.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
MODULE_SUPPORTED_DEVICE was added in pre-git era and never was
implemented. We can safely remove it, because the kernel has grown
to have many more reliable mechanisms to determine if device is
supported or not.
Signed-off-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add Watchdog support for ROHM BD9576MUF and BD9573MUF PMICs which are
mainly used to power the R-Car series processors. The watchdog is
pinged using a GPIO and enabled using another GPIO. Additionally
watchdog time-out can be configured to HW prior starting the watchdog.
Watchdog timeout can be configured to detect only delayed ping or in
a window mode where also too fast pings are detected.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here is the large set of char/misc/whatever driver subsystem updates for
5.12-rc1. Over time it seems like this tree is collecting more and more
tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86
maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only reported
issue being a merge conflict in include/linux/mod_devicetable.h that you
will hit in your tree due to the dfl_device_id addition from the fpga
subsystem in here. The resolution should be simple.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCYDZf9w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk3xgCcCEN+pCJTum+uAzSNH3YKs/onaDgAnRSVwOUw
tNW6n1JhXLYl9f5JdhvS
=MOHs
-----END PGP SIGNATURE-----
Merge tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the large set of char/misc/whatever driver subsystem updates
for 5.12-rc1. Over time it seems like this tree is collecting more and
more tiny driver subsystems in one place, making it easier for those
maintainers, which is why this is getting larger.
Included in here are:
- coresight driver updates
- habannalabs driver updates
- virtual acrn driver addition (proper acks from the x86 maintainers)
- broadcom misc driver addition
- speakup driver updates
- soundwire driver updates
- fpga driver updates
- amba driver updates
- mei driver updates
- vfio driver updates
- greybus driver updates
- nvmeem driver updates
- phy driver updates
- mhi driver updates
- interconnect driver udpates
- fsl-mc bus driver updates
- random driver fix
- some small misc driver updates (rtsx, pvpanic, etc.)
All of these have been in linux-next for a while, with the only
reported issue being a merge conflict due to the dfl_device_id
addition from the fpga subsystem in here"
* tag 'char-misc-5.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (311 commits)
spmi: spmi-pmic-arb: Fix hw_irq overflow
Documentation: coresight: Add PID tracing description
coresight: etm-perf: Support PID tracing for kernel at EL2
coresight: etm-perf: Clarify comment on perf options
ACRN: update MAINTAINERS: mailing list is subscribers-only
regmap: sdw-mbq: use MODULE_LICENSE("GPL")
regmap: sdw: use no_pm routines for SoundWire 1.2 MBQ
regmap: sdw: use _no_pm functions in regmap_read/write
soundwire: intel: fix possible crash when no device is detected
MAINTAINERS: replace my with email with replacements
mhi: Fix double dma free
uapi: map_to_7segment: Update example in documentation
uio: uio_pci_generic: don't fail probe if pdev->irq equals to IRQ_NOTCONNECTED
drivers/misc/vmw_vmci: restrict too big queue size in qp_host_alloc_queue
firewire: replace tricky statement by two simple ones
vme: make remove callback return void
firmware: google: make coreboot driver's remove callback return void
firmware: xilinx: Use explicit values for all enum values
sample/acrn: Introduce a sample of HSM ioctl interface usage
virt: acrn: Introduce an interface for Service VM to control vCPU
...
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
-----BEGIN PGP SIGNATURE-----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=BULT
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm
Pull ARM updates from Russell King:
- Generalise byte swapping assembly
- Update debug addresses for STI
- Validate start of physical memory with DTB
- Do not clear SCTLR.nTLSMD in decompressor
- amba/locomo/sa1111 devices remove method return type is void
- address markers for KASAN in page table dump
* tag 'for-linus' of git://git.armlinux.org.uk/~rmk/linux-arm:
ARM: 9065/1: OABI compat: fix build when EPOLL is not enabled
ARM: 9055/1: mailbox: arm_mhuv2: make remove callback return void
amba: Make use of bus_type functions
amba: Make the remove callback return void
vfio: platform: simplify device removal
amba: reorder functions
amba: Fix resource leak for drivers without .remove
ARM: 9054/1: arch/arm/mm/mmu.c: Remove duplicate header
ARM: 9053/1: arm/mm/ptdump:Add address markers for KASAN regions
ARM: 9051/1: vdso: remove unneded extra-y addition
ARM: 9050/1: Kconfig: Select ARCH_HAVE_NMI_SAFE_CMPXCHG where possible
ARM: 9049/1: locomo: make locomo bus's remove callback return void
ARM: 9048/1: sa1111: make sa1111 bus's remove callback return void
ARM: 9047/1: smp: remove unused variable
ARM: 9046/1: decompressor: Do not clear SCTLR.nTLSMD for ARMv7+ cores
ARM: 9045/1: uncompress: Validate start of physical memory against passed DTB
ARM: 9042/1: debug: no uncompress debugging while semihosting
ARM: 9041/1: sti LL_UART: add STiH418 SBC UART0 support
ARM: 9040/1: use DEBUG_UART_PHYS and DEBUG_UART_VIRT for sti LL_UART
ARM: 9039/1: assembler: generalize byte swapping macro into rev_l
- Microsoft Surface devices System Aggregator Module support
- SW_TABLET_MODE reporting improvements
- thinkpad_acpi keyboard language setting support
- platform / DPTF profile settings support
- Base / userspace API parts merged from Rafael's acpi-platform branch
- thinkpad_acpi and ideapad-laptop support through pdx86
- Remove support for some obsolete Intel MID platforms through merging
of the shared intel-mid-removal branch
- Big cleanup of the ideapad-laptop driver
- Misc. other fixes / new hw support / quirks
The following is an automated git shortlog grouped by driver:
ACPI:
- platform-profile: Fix possible deadlock in platform_profile_remove()
- platform-profile: Introduce object pointers to callbacks
- platform-profile: Drop const qualifier for cur_profile
- platform: Add platform profile support
Documentation:
- Add documentation for new platform_profile sysfs attribute
Documentation/ABI:
- sysfs-platform-ideapad-laptop: conservation_mode attribute
- sysfs-platform-ideapad-laptop: update device attribute paths
Kconfig:
- add missing selects for ideapad-laptop
MAINTAINERS:
- update email address for Henrique de Moraes Holschuh
Merge remote-tracking branch 'intel-speed-select/intel-sst' into review-hans:
- Merge remote-tracking branch 'intel-speed-select/intel-sst' into review-hans
Merge remote-tracking branch 'linux-pm/acpi-platform' into review-hans:
- Merge remote-tracking branch 'linux-pm/acpi-platform' into review-hans
Merge tag 'ib-drm-gpio-pdx86-rtc-wdt-v5.12-1' into for-next:
- Merge tag 'ib-drm-gpio-pdx86-rtc-wdt-v5.12-1' into for-next
Move all dell drivers to their own subdirectory:
- Move all dell drivers to their own subdirectory
Platform:
- OLPC: Constify static struct regulator_ops
- OLPC: Specify the enable time
- OLPC: Remove dcon_rdev from olpc_ec_priv
- OLPC: Fix probe error handling
Revert "platform/x86:
- ideapad-laptop: Switch touchpad attribute to be RO"
acer-wmi:
- Don't use ACPI_EXCEPTION()
amd-pmc:
- put device on error paths
- Fix CONFIG_DEBUG_FS check
dell-wmi-sysman:
- fix a NULL pointer dereference
docs:
- driver-api: Add Surface Aggregator subsystem documentation
drm/gma500:
- Get rid of duplicate NULL checks
- Convert to use new SCU IPC API
gpio:
- msic: Remove driver for deprecated platform
- intel-mid: Remove driver for deprecated platform
hp-wmi:
- Disable tablet-mode reporting by default
- Don't log a warning on HPWMI_RET_UNKNOWN_COMMAND errors
i2c-multi-instantiate:
- Don't create platform device for INT3515 ACPI nodes
ideapad-laptop:
- add "always on USB charging" control support
- add keyboard backlight control support
- send notification about touchpad state change to sysfs
- fix checkpatch warnings, more consistent style
- change 'cfg' debugfs file format
- change 'status' debugfs file format
- check for touchpad support in _CFG
- check for Fn-lock support in HALS
- rework is_visible() logic
- rework and create new ACPI helpers
- group and separate (un)related constants into enums
- misc. device attribute changes
- always propagate error codes from device attributes' show() callback
- convert ACPI helpers to return -EIO in case of failure
- use dev_{err,warn} or appropriate variant to display log messages
- use msecs_to_jiffies() helper instead of hand-crafted formula
- use for_each_set_bit() helper to simplify event processing
- use kobj_to_dev()
- use device_{add,remove}_group
- use sysfs_emit()
- add missing call to submodule destructor
- sort includes lexicographically
- use appropriately typed variable to store the return value of ACPI methods
- remove unnecessary NULL checks
- remove unnecessary dev_set_drvdata() call
- DYTC Platform profile support
- Disable touchpad_switch for ELAN0634
intel-vbtn:
- Eval VBDL after registering our notifier
- Add alternative method to enable switches
- Create 2 separate input-devs for buttons and switches
- Rework wakeup handling in notify_handler()
- Drop HP Stream x360 Convertible PC 11 from allow-list
- Support for tablet mode on Dell Inspiron 7352
intel_mid_powerbtn:
- Remove driver for deprecated platform
- Remove driver for deprecated platform
intel_mid_thermal:
- Remove driver for deprecated platform
- Remove driver for deprecated platform
intel_pmt:
- Make INTEL_PMT_CLASS non-user-selectable
intel_pmt_crashlog:
- Add dependency on MFD_INTEL_PMT
intel_pmt_telemetry:
- Add dependency on MFD_INTEL_PMT
intel_scu_ipc:
- Increase virtual timeout from 3 to 5 seconds
intel_scu_wdt:
- Drop mistakenly added const
- Get rid of custom x86 model comparison
- Drop SCU notification
- Move driver from arch/x86
msi-wmi:
- Fix variable 'status' set but not used compiler warning
platform/surface:
- aggregator: Fix access of unaligned value
- Add Surface Hot-Plug driver
- surface3-wmi: Fix variable 'status' set but not used compiler warning
- aggregator: Fix braces in if condition with unlikely() macro
- aggregator: Fix kernel-doc references
- aggregator: fix a kernel-doc markup
- aggregator_cdev: Add comments regarding unchecked allocation size
- aggregator_cdev: Fix access of uninitialized variables
- fix potential integer overflow on shift of a int
- Add Surface ACPI Notify driver
- Add Surface Aggregator user-space interface
- aggregator: Add dedicated bus and device type
- aggregator: Add error injection capabilities
- aggregator: Add trace points
- aggregator: Add event item allocation caching
- aggregator: Add control packet allocation caching
- Add Surface Aggregator subsystem
- SURFACE_PLATFORMS should depend on ACPI
- surface_gpe: Fix non-PM_SLEEP build warnings
platform/x86/intel-uncore-freq:
- Add Sapphire Rapids server support
rtc:
- mrst: Remove driver for deprecated platform
sony-laptop:
- Remove unneeded semicolon
thinkpad_acpi:
- Replace ifdef CONFIG_ACPI_PLATFORM_PROFILE with depends on
- Fix 'warning: no previous prototype for' warnings
- Add platform profile support
- fixed warning and incorporated review comments
- rectify length of title underline
- Don't register keyboard_lang unnecessarily
- set keyboard language
- Add P53/73 firmware to fan_quirk_table for dual fan control
- correct palmsensor error checking
tools/power/x86/intel-speed-select:
- Update version to 1.8
- Add new command to get/set TRL
- Add new command turbo-mode
- Set higher of cpuinfo_max_freq or base_frequency
- Set scaling_max_freq to base_frequency
touchscreen_dmi:
- Add info for the Jumper EZpad 7 tablet
- Add swap-x-y quirk for Goodix touchscreen on Estar Beauty HD tablet
watchdog:
- intel-mid_wdt: Postpone IRQ handler registration till SCU is ready
- intel_scu_watchdog: Remove driver for deprecated platform
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmAqZ5cUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9zmuwf/XLoZzs6oW7Ps9DhkyU5lk7D79rti
DY4AabVnWZhJ+Yl5+qMCTjC0R0nJYoq9PCDU5q20HHSFq7PXV0fPEVo7ZOp8tPng
wdzb2glbtGjSWksjj3c8eB/jjPP0tpsWptH+9jlTv9yXwQNVh/rPVltmD+z8y69U
qNzySltQMtoKmQKNbktUeHA12jBldnH+QlkL8KUp5ZEVDd7gukkmAovpzEcnwk5U
lrza7I52c9Ggu1pD2OCX7an9tk6N7mQ6Rk2/c6GzRsOYa6SC5Aj7fi2bs0LRdGGx
Kz/gtKS3dRIreEs4LGmL8byVi7a/YvCQoTfO+MxKq/btedBwxO2edDDsRg==
=B+Fz
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86
Pull x86 platform driver updates from Hans de Goede:
"Highlights:
- Microsoft Surface devices System Aggregator Module support
- SW_TABLET_MODE reporting improvements
- thinkpad_acpi keyboard language setting support
- platform / DPTF profile settings support:
- Base / userspace API parts merged from Rafael's acpi-platform
branch
- thinkpad_acpi and ideapad-laptop support through pdx86
- Remove support for some obsolete Intel MID platforms through
merging of the shared intel-mid-removal branch
- Big cleanup of the ideapad-laptop driver
- Misc other fixes / new hw support / quirks"
* tag 'platform-drivers-x86-v5.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86: (99 commits)
platform/x86: intel_scu_ipc: Increase virtual timeout from 3 to 5 seconds
platform/surface: aggregator: Fix access of unaligned value
tools/power/x86/intel-speed-select: Update version to 1.8
tools/power/x86/intel-speed-select: Add new command to get/set TRL
tools/power/x86/intel-speed-select: Add new command turbo-mode
Platform: OLPC: Constify static struct regulator_ops
platform/surface: Add Surface Hot-Plug driver
platform/x86: intel_scu_wdt: Drop mistakenly added const
platform/x86: Kconfig: add missing selects for ideapad-laptop
platform/x86: acer-wmi: Don't use ACPI_EXCEPTION()
platform/x86: thinkpad_acpi: Replace ifdef CONFIG_ACPI_PLATFORM_PROFILE with depends on
platform/x86: thinkpad_acpi: Fix 'warning: no previous prototype for' warnings
platform/x86: msi-wmi: Fix variable 'status' set but not used compiler warning
platform/surface: surface3-wmi: Fix variable 'status' set but not used compiler warning
platform/x86: Move all dell drivers to their own subdirectory
Documentation/ABI: sysfs-platform-ideapad-laptop: conservation_mode attribute
Documentation/ABI: sysfs-platform-ideapad-laptop: update device attribute paths
platform/x86: ideapad-laptop: add "always on USB charging" control support
platform/x86: ideapad-laptop: add keyboard backlight control support
platform/x86: ideapad-laptop: send notification about touchpad state change to sysfs
...
The driver core ignores the return value of mei_cl_device_remove() so
passing an error value doesn't solve any problem. As most mei drivers'
remove callbacks return 0 unconditionally and returning a different value
doesn't have any effect, change this prototype to return void and return 0
unconditionally in mei_cl_device_remove(). The only driver that could
return an error value is modified to emit an explicit warning in the error
case.
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210208073705.428185-3-uwe@kleine-koenig.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per register documentation, QCOM_WDT_ENABLE_IRQ which is BIT(1)
of watchdog control register is wakeup interrupt enable bit and
not related to bark interrupt at all, BIT(0) is used for that.
So remove incorrect usage of this bit when supporting bark irq for
pre-timeout notification. Currently with this bit set and bark
interrupt specified, pre-timeout notification and/or watchdog
reset/bite does not occur.
Fixes: 36375491a4 ("watchdog: qcom: support pre-timeout when the bark irq is available")
Cc: stable@vger.kernel.org
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Link: https://lore.kernel.org/r/20210126150241.10009-1-saiprakash.ranjan@codeaurora.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The MEI bus has a special behavior on suspend it destroys
all the attached devices, this is due to the fact that also
firmware context is not persistent across power flows.
If watchdog on MEI bus is ticking before suspending the firmware
times out and reports that the OS is missing watchdog tick.
Send the stop command to the firmware on watchdog unregistered
to eliminate the false event on suspend.
This does not make the things worse from the user-space perspective
as a user-space should re-open watchdog device after
suspending before this patch.
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210124114938.373885-1-tomas.winkler@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The tango platform is getting removed, so the driver is no
longer needed.
Cc: Marc Gonzalez <marc.w.gonzalez@free.fr>
Cc: Mans Rullgard <mans@mansr.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Mans Rullgard <mans@mansr.com>
Link: https://lore.kernel.org/r/20210120162745.61268-5-arnd@kernel.org
[groeck: Removed devicetree bindings]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The zte zx platform is getting removed, so this driver is no
longer needed.
Cc: Jun Nie <jun.nie@linaro.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210120162745.61268-4-arnd@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120162745.61268-3-arnd@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The CSR SiRF prima2/atlas platforms are getting removed, so this driver
is no longer needed.
Cc: Barry Song <baohua@kernel.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Barry Song <baohua@kernel.org>
Link: https://lore.kernel.org/r/20210120162745.61268-2-arnd@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Before user space daemon start to access the watchdog device,
there is a time interval that watchdog is disabled in the
original flow. If the system freezing at this interval, it
cannot be rebooted by watchdog hardware automatically.
In order to solve this problem, the watchdog hardware should be
kept working, and start hrtimer in framework to ping it by
setting max_hw_heartbeat_ms and HW_RUNNING used in
watchdog_need_worker to determine whether the worker should be
started or not. Besides the redundant setting of max_timeout is
also removed.
Signed-off-by: freddy.hsin <freddy.hsin@mediatek.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1609316157-3748-1-git-send-email-freddy.hsin@mediatek.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
arm64 does not have a grace period after calling reset handlers. It is
rightfully assumed that watchdog drivers should wait because they know
the time needed. Implement this for the Renesas watchdog driver.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@oeck-us.net>
Link: https://lore.kernel.org/r/20210118094558.36814-1-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In watchdog_reboot_notifier, wdd should be stopped when the device
is in hw_running state
Signed-off-by: Zhao Qiang <qiang.zhao@nxp.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210114082651.17162-1-qiang.zhao@nxp.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Remove including <linux/version.h> that don't need it.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1608886154-55309-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
In the restart handler, we hit multiple OOPSes. One because of
usleep_range() and one because of RPM. So, instead of re-using
rwdt_start(), we implement an atomic version of it in the restart
handler. As a little bonus, reboot will occur sooner because we can now
use the smallest divider in the custom restart routine.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20201219173415.21848-1-wsa+renesas@sang-engineering.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Defining DEBUG should only be done in development.
So remove DEBUG.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20210115153237.131357-1-trix@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
All amba drivers return 0 in their remove callback. Together with the
driver core ignoring the return value anyhow, it doesn't make sense to
return a value here.
Change the remove prototype to return void, which makes it explicit that
returning an error value doesn't work as expected. This simplifies changing
the core remove callback to return void, too.
Reviewed-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org> # for drivers/memory
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Suzuki K Poulose <suzuki.poulose@arm.com> # for hwtracing/coresight
Acked-By: Vinod Koul <vkoul@kernel.org> # for dmaengine
Acked-by: Guenter Roeck <linux@roeck-us.net> # for watchdog
Acked-by: Wolfram Sang <wsa@kernel.org> # for I2C
Acked-by: Takashi Iwai <tiwai@suse.de> # for sound
Acked-by: Vladimir Zapolskiy <vz@mleia.com> # for memory/pl172
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Link: https://lore.kernel.org/r/20210126165835.687514-5-u.kleine-koenig@pengutronix.de
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
The driver core ignores the return value of the remove callback, so
don't give isa drivers the chance to provide a value.
Adapt all isa_drivers with a remove callbacks accordingly; they all
return 0 unconditionally anyhow.
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for drivers/net/can/sja1000/tscan1.c
Acked-by: William Breathitt Gray <vilhelm.gray@gmail.com>
Acked-by: Wolfram Sang <wsa@kernel.org> # for drivers/i2c/
Reviewed-by: Takashi Iway <tiwai@suse.de> # for sound/
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for drivers/media/
Signed-off-by: Uwe Kleine-König <uwe@kleine-koenig.org>
Link: https://lore.kernel.org/r/20210122092449.426097-4-uwe@kleine-koenig.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When SCU is not ready and CONFIG_DEBUG_SHIRQ=y we got deferred probe followed
by fired test IRQ which immediately makes kernel panic. Fix this by delaying
IRQ handler registration till SCU is ready.
Fixes: 80ae679b8f ("watchdog: intel-mid_wdt: Convert to use new SCU IPC API")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Intel Moorestown and Medfield are quite old Intel Atom based
32-bit platforms, which were in limited use in some Android phones,
tablets and consumer electronics more than eight years ago.
There are no bugs or problems ever reported outside from Intel
for breaking any of that platforms for years. It seems no real
users exists who run more or less fresh kernel on it. The commit
05f4434bc1 ("ASoC: Intel: remove mfld_machine") also in align
with this theory.
Due to above and to reduce a burden of supporting outdated drivers
we remove the support of outdated platforms completely.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAl/jfRcACgkQ+iyteGJfRspXnQCfYAyqptMHDHGC98z5kFpsIcxg
R6MAmQG3jN5aUiwrKcGG2NxQlEGeGVLq
=bHWM
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.11-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- Removal of the pnx83xx driver
- Add a binding for A100's watchdog controller
- Add Rockchip compatibles to snps,dw-wdt.yaml
- hpwdt: Disable NMI in Crash Kernel
- Fix potential dereferencing of null pointer in watchdog_core
- Several other small fixes and improvements
* tag 'linux-watchdog-5.11-rc1' of git://www.linux-watchdog.org/linux-watchdog: (23 commits)
watchdog: convert comma to semicolon
watchdog: iTCO_wdt: use dev_*() instead of pr_*() for logging
dt-binding: watchdog: add Rockchip compatibles to snps,dw-wdt.yaml
watchdog: coh901327: add COMMON_CLK dependency
dt-bindings: watchdog: sun4i: Add A100 compatible
watchdog: qcom: Avoid context switch in restart handler
watchdog: iTCO_wdt: use module_platform_device() macro
watchdog: Fix potential dereferencing of null pointer
watchdog: wdat_wdt: Fix missing kerneldoc reported by W=1
watchdog/hpwdt: Reflect changes
watchdog/hpwdt: Disable NMI in Crash Kernel
wdt: sp805: add watchdog_stop on reboot
watchdog: sbc_fitpc2_wdt: add __user annotations
watchdog: geodewdt: remove unneeded break
watchdog: rti-wdt: fix reference leak in rti_wdt_probe
watchdog: qcom_wdt: set WDOG_HW_RUNNING bit when appropriate
watchdog: remove pnx83xx driver
watchdog: stm32_iwdg: don't print an error on probe deferral
watchdog: sprd: change to use usleep_range() instead of busy loop
watchdog: sprd: check busy bit before new loading rather than after that
...
For device log outputs, it's better to have device name / ID
prefixed in all messages, so use the proper dev_*() functions here.
Explicit message on module load/unload don't seem to be really helpful
(we have other means to check which modules have been loaded), instead
just add noise to the kernel log. So, removing them.
Signed-off-by: Enrico Weigelt, metux IT consult <info@metux.net>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201117152214.32244-2-info@metux.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
clang produces a build failure in configurations without COMMON_CLK
when a timeout calculation goes wrong:
arm-linux-gnueabi-ld: drivers/watchdog/coh901327_wdt.o: in function `coh901327_enable':
coh901327_wdt.c:(.text+0x50): undefined reference to `__bad_udelay'
Add a Kconfig dependency to only do build testing when COMMON_CLK
is enabled.
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201203223358.1269372-1-arnd@kernel.org
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
A reboot notifier, which stops the WDT by calling the stop hook without
any check, would be registered when we set WDOG_STOP_ON_REBOOT flag.
Howerer we allow the WDT driver to omit the stop hook since commit
"d0684c8a93549" ("watchdog: Make stop function optional") and provide
a module parameter for user that controls the WDOG_STOP_ON_REBOOT flag
in commit 9232c80659 ("watchdog: Add stop_on_reboot parameter to
control reboot policy"). Together that commits make user potential to
insert a watchdog driver that don't provide a stop hook but with the
stop_on_reboot parameter set, then dereferencing of null pointer occurs
on system reboot.
Check the stop hook before registering the reboot notifier to fix the
issue.
Fixes: d0684c8a93 ("watchdog: Make stop function optional")
Signed-off-by: Wang Wensheng <wangwensheng4@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201109130512.28121-1-wangwensheng4@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Fix the following warning while compiling with W=1.
drivers/watchdog/wdat_wdt.c:48: warning: Function parameter or member 'instructions' not described in 'wdat_wdt'
Signed-off-by: Wong Vee Khee <vee.khee.wong@intel.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201111172205.17215-1-vee.khee.wong@intel.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
NMIs received during the crash path are problematic as hpwdt_pretimeout
handling of the NMI would cause a reentry into kdump.
The situation is complicated in that I/O errors can be signaled as NMI
circumventing hpwdt_pretimeout's attempt to not claim NMI not associated
with either the WDT or the iLO NMI switch. These NMI can additionally
cause a secondary NMI which cause the system to hang.
By disabling pretimeout and hpwdtimeout in crash path we both reduce
the risk of receiving an NMI and simuletaneously leave the WDT running
(if it was already in use) to allow the WDT to break the system out of
hangs by the WDT reset.
Signed-off-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/1606097320-56762-2-git-send-email-jerry.hoemann@hpe.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
After a change to the put_user() macro on x86, kernel test robot has
started sending me complaints (from sparse) about passing kernel
pointers to put_user(). So add the __user annotations to the various
casts in fitpc2_wdt_ioctl(), and while in here, also make the write
method actually match the prototype of file_operations::write.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Reviewed-by: Guenter Roeck <inux@roeck-us.net>
Link: https://lore.kernel.org/r/20201025124518.31647-1-linux@rasmusvillemoes.dk
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
A break is not needed if it is preceded by a return
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201019175342.2646-1-trix@redhat.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
pm_runtime_get_sync() will increment pm usage counter even it
failed. Forgetting to call pm_runtime_put_noidle will result
in reference leak in rti_wdt_probe, so we should fix it.
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201030154909.100023-1-zhangqilong3@huawei.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
If the watchdog hardware is enabled/running during boot, e.g.
due to a boot loader configuring it, we must tell the
watchdog framework about this fact so that it can ping the
watchdog until userspace opens the device and takes over
control.
Do so using the WDOG_HW_RUNNING flag that exists for exactly
that use-case.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201031121115.542752-1-robert.marko@sartura.hr
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Commit 625326ea9c ("MIPS: Remove PNX833x alias NXP_STB22x") removed
support for PNX833x, so it's time to remove watchdog driver, too.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201106130508.103598-1-tsbogend@alpha.franken.de
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
After changing to check busy bit for the previous loading operation instead
of the current one, for most of cases, the busy bit is not set for the
first time of read, so there's no need to check so frequently, so this
patch use usleep_range() to replace cpu_relax() to avoid busy loop.
Also this patch change the max times to 11 which would be enough, since
according to the specification, the busy bit would be set after a new
loading operation and last 2 or 3 RTC clock cycles (about 60us~92us).
Fixes: 4776034670 ("watchdog: Add Spreadtrum watchdog driver")
Original-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201029023933.24548-4-zhang.lyra@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
As the specification described, users must check busy bit before start
a new loading operation to make sure that the previous loading is done
and the device is ready to accept a new one.
[ chunyan: Massaged changelog ]
Fixes: 4776034670 ("watchdog: Add Spreadtrum watchdog driver")
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201029023933.24548-3-zhang.lyra@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
sprd_wdt_start() would return fail if the loading operation is not completed
in a certain time, disabling watchdog for that case would probably cause
the kernel crash when kick watchdog later, that's too bad, so remove the
watchdog disable operation for the fail case to make sure other parts in
the kernel can run normally.
[ chunyan: Massaged changelog ]
Fixes: 4776034670 ("watchdog: Add Spreadtrum watchdog driver")
Signed-off-by: Lingling Xu <ling_ling.xu@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Link: https://lore.kernel.org/r/20201029023933.24548-2-zhang.lyra@gmail.com
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
If HAS_IOMEM is not defined and SIRFSOC_WATCHDOG is enabled,
the build fails with the following error.
drivers/watchdog/sirfsoc_wdt.o: in function `sirfsoc_wdt_probe':
sirfsoc_wdt.c:(.text+0x112):
undefined reference to `devm_platform_ioremap_resource'
Reported-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Fixes: da2a68b3eb ("watchdog: Enable COMPILE_TEST where possible")
Link: https://lore.kernel.org/r/20201108162550.27660-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
The following kbuild warning is seen on a system without HAS_IOMEM.
WARNING: unmet direct dependencies detected for MFD_SYSCON
Depends on [n]: HAS_IOMEM [=n]
Selected by [y]:
- ARMADA_37XX_WATCHDOG [=y] && WATCHDOG [=y] && (ARCH_MVEBU || COMPILE_TEST
This results in a subsequent compile error.
drivers/watchdog/armada_37xx_wdt.o: in function `armada_37xx_wdt_probe':
armada_37xx_wdt.c:(.text+0xdc): undefined reference to `devm_ioremap'
Add the missing dependency.
Reported-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Fixes: 54e3d9b518 ("watchdog: Add support for Armada 37xx CPU watchdog")
Link: https://lore.kernel.org/r/20201108162550.27660-1-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
Russell said that he is no longer using this machine, and it seems that
nobody else has in a long time, so it's time to say goodbye to it.
As this is the last platform using CONFIG_ARCH_USES_GETTIMEOFFSET,
there are some follow-up patches to remove that as well.
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.14 (GNU/Linux)
iEYEABECAAYFAl+QLMUACgkQ+iyteGJfRsreMACcDuI5w/3sJ5kmjasDm0e7dLte
20gAoL4kLcLAD2v8HiV8RPR+HYyvuic5
=MLjG
-----END PGP SIGNATURE-----
Merge tag 'linux-watchdog-5.10-rc1' of git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- Add Toshiba Visconti watchdog driver
- it87_wdt: add IT8772 + IT8784
- several fixes and improvements
* tag 'linux-watchdog-5.10-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: Add Toshiba Visconti watchdog driver
watchdog: bindings: Add binding documentation for Toshiba Visconti watchdog device
watchdog: it87_wdt: add IT8784 ID
watchdog: sp5100_tco: Enable watchdog on Family 17h devices if disabled
watchdog: sp5100: Fix definition of EFCH_PM_DECODEEN3
watchdog: renesas_wdt: support handover from bootloader
watchdog: imx7ulp: Watchdog should continue running for wait/stop mode
watchdog: rti: Simplify with dev_err_probe()
watchdog: davinci: Simplify with dev_err_probe()
watchdog: cadence: Simplify with dev_err_probe()
watchdog: remove unneeded inclusion of <uapi/linux/sched/types.h>
watchdog: Use put_device on error
watchdog: Fix memleak in watchdog_cdev_register
watchdog: imx7ulp: Strictly follow the sequence for wdog operations
watchdog: it87_wdt: add IT8772 ID
watchdog: pcwd_usb: Avoid GFP_ATOMIC where it is not needed
drivers: watchdog: rdc321x_wdt: Fix race condition bugs
On Family 17h (Ryzen) devices, the WatchdogTmrEn bit of PmDecodeEn not only
enables watchdog memory decoding at 0xfeb00000, it also enables the
watchdog hardware itself. Use this information to enable the watchdog if
it is not already enabled.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Link: https://lore.kernel.org/r/20200910163109.235136-2-linux@roeck-us.net
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Wim Van Sebroeck <wim@linux-watchdog.org>
