Only the option driver implements the send_setup callback; it uses the
SET_CONTROL_LINE_STATE request in CDC ACM to generate DTR/RTS signals
on the port. This is not driver-specific though and is needed by other
drivers, so move the function to the usb_wwan driver (with formatting
tweaks), and replace the callback pointer with a flag that enables the
request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
This is a partial, context modified revert of commit e463c6dda8
("USB: option: handle send_setup blacklisting at probe"), which
introduced an unnecessary struct option_private for storing the
interface number used in option_send_setup. Removing this struct
will allow option_send_setup to be generalized for other drivers.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove extra blank lines in the several places where functions were
separated by more than one.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Fix non-standard formatting in some of the comments.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
[johan: minor fixes ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Move request_firmware from edge_startup to download_fw.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Separate the download and boot mode code from download_fw() into two new
helper functions: do_download_mode() and do_boot_mode().
Signed-off-by: Peter E. Berger <pberger@brimson.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use serial->interface instead of serial->dev for messages in download_fw().
Signed-off-by: Peter E. Berger <pberger@brimson.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove unused "dev" parameter from build_i2c_fw_hdr() and its caller.
Signed-off-by: Peter E. Berger <pberger@brimson.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Add a device quirk for the Logitech PTZ Pro Camera and its sibling the
ConferenceCam CC3000e Camera.
This fixes the failed camera enumeration on some boot, particularly on
machines with fast CPU.
Tested by connecting a Logitech PTZ Pro Camera to a machine with a
Haswell Core i7-4600U CPU @ 2.10GHz, and doing thousands of reboot cycles
while recording the kernel logs and taking camera picture after each boot.
Before the patch, more than 7% of the boots show some enumeration transfer
failures and in a few of them, the kernel is giving up before actually
enumerating the webcam. After the patch, the enumeration has been correct
on every reboot.
Signed-off-by: Vincent Palatin <vpalatin@chromium.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Rng reads in chaoskey driver could return the same data under
the certain conditions.
Signed-off-by: Alexander Inyukhin <shurick@sectorb.msk.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
These two headphones need a reset-resume quirk to properly resume to
original volume level.
Signed-off-by: Yao-Wen Mao <yaowen@google.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch adds a compatible string to support for R-Car H3.
Since the HS-USB controller of R-Car H3 is almost the same specification
with R-Car Gen2 (these have 16 pipes and usb-dmac), this patch
sets the "type" of renesas_usbhs_driver_param to USBHS_TYPE_RCAR_GEN2.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following warning if 64-bit architecture environment:
./drivers/usb/renesas_usbhs/common.c:496:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
dparam->type = of_id ? (u32)of_id->data : 0;
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In a situation where the urb is about to be returned or was never
there, we should return -EIDRM (as per usb_hcd_check_unlink_urb).
This is exactly the situation when the urb is picked up by vhci_rx
before we access priv.
Return -EIDRM rather than 0 when this happens.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We handle USB_REQ_SET_ADDRESS at enqueue, so we want to perform
cleanup and giveback the urb. We should not call usb_hcd_giveback_urb
when we're cleaning up after a failed enqueue, though.
Only giveback the urb at cleanup when we claim to have served it.
Signed-off-by: Igor Kotrasinski <i.kotrasinsk@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The function can return negative values.
The problem has been detected using proposed semantic patch
scripts/coccinelle/tests/unsigned_lesser_than_zero.cocci [1].
[1]: http://permalink.gmane.org/gmane.linux.kernel/2038576
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Previously, Coccinelle would issue the following false positive:
isd200.c:1478:14-18: ERROR: reference preceded by free on line 1472
This change rewrites the isd200_init_info function to have more explicit
execution pathways to make it easier for scripts and humans to parse.
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Before running the platform_driver_unregister() the code will either return
retval or jump to clean. Removing this line that is unreachable.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This platform driver has a OF device ID table but the OF module
alias information is not created so module autoloading won't work.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since a_alt_hnp_support is obsolete in OTG 2.0, HNP capable host should
send this set feature request only if the otg device is connecting to a
non-HNP port and it's compliant with OTG 1.x revision. This is done by
checking its otg descriptor length, OTG 2.0 uses usb_otg20_descriptor
which has different length than OTG 1.x using usb_otg_descriptor.
Signed-off-by: Li Jun <jun.li@freescale.com>
Acked-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use kmalloc_array instead of kmalloc to allocate memory for an array.
Also, remove the dev_warn for a memory leak, making the if check more
sleek.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This enables USB on the ARM juno board when booted with
an ACPI kernel. The PNP id comes from the PNP/ACPI registry
and describes an EHCI controller without debug.
Tested-by: Huang Shijie <shijie.huang@arm.com>
Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the ehci driver fails to configure the dma settings then display
a dev error instead of simply failing. This is triggered in an
ACPI world if the user fails to set the _CCA on the device.
Tested-by: Huang Shijie <shijie.huang@arm.com>
Reviewed-by: Graeme Gregory <graeme.gregory@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jeremy Linton <jeremy.linton@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the Sparse warning:
message.c:1390:21: warning: symbol 'i' shadows an earlier one
message.c:1294:13: originally declared here
Signed-off-by: Kris Borer <kborer@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-ESHUTDOWN means that the HC has been unplugged.
Reporting an error in that case makes no sense.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit d445913ce0 ("usb: ehci-orion: add optional PHY support")
added support for optional phys, but devm_phy_optional_get returns
-ENOSYS if GENERIC_PHY is not enabled.
This causes probe failures, even when there are no phys specified:
[ 1.443365] orion-ehci f1058000.usb: init f1058000.usb fail, -38
[ 1.449403] orion-ehci: probe of f1058000.usb failed with error -38
Similar to dwc3, treat -ENOSYS as no phy.
Fixes: d445913ce0 ("usb: ehci-orion: add optional PHY support")
Signed-off-by: Jonas Gorski <jogo@openwrt.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix two occurrences of the Sparse warning:
warning: symbol XXX shadows an earlier one
Signed-off-by: Kris Borer <kborer@gmail.com>
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In big endian cases, macro cpu_to_le16 unfolds to __swab16 which
provides special case for constants. In little endian cases,
__constant_cpu_to_le16 and cpu_to_le16 expand directly to the
same expression. So, replace __constant_cpu_to_le16 with
cpu_to_le16 with the goal of getting rid of the definition of
__constant_cpu_to_le16 completely.
The semantic patch that performs this transformation is as follows:
@@expression x;@@
- __constant_cpu_to_le16(x)
+ cpu_to_le16(x)
Signed-off-by: Vaishali Thakkar <vthakkar1994@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Removed some checkpatch.pl warnings saying there was an unwanted space
between function names and their arguments.
Signed-off-by: Chase Metzger <chasemetzger15@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.1 adds different types of Get Port Status request.
The Get Extended Port Status request returns 4 additional bytes
after the normal portstatus and portchange words containing
link speed and lane information about a connected enhanced super
speed device
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the controller speed to HCD_USB31 to if host hardware supports USB 3.1
For PCI xhci controllers the USB 3.1 support is checked from SBRN bits in
pci config space. Platform controllers will need to set xhci->sbrn == 0x31
to indicate USB 3.1 support before calling xhci_gen_setup().
Also make sure xhci driver works correctly with speed set to HCD_USB31
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hosts that support USB 3.1 Enhaned SuperSpeed can set their speed to
HCD_USB31 to let usb core and host drivers know that the controller
supports new USB 3.1 features.
make sure usb core handle HCD_USB31 hosts correctly, for now similar
to HCD_USB3.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB 3.1 capable xhci controllers use a new default speed ID "5" in the
PORTSC register to represent a 10Gbps connection speed of a SuperSpeedPlus
device
Make sure the xhci driver can handle the returned SuperSpeedPlus speed ID
properly
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All usb devices that support USB 3.1 Gen2 speeds need to provide a
SuperSpeedPlus device capability descriptor as part of their BOS
descriptor.
If the xhci controller supports USB 3.1 enhanced SuperSpeed, meaning
it can handle both Gen1 SuperSpeed 5Gbps and Gen2 SuperSpeedPlus 10Gbps
devices, then we need to provide a SuperSpeedPlus capability descriptor
for the USB 3.1 roothub as well.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci 1.1 controllers that support USB 3.1 must provide a protocol speed ID
(PSI) list to inform the driver of the supported speeds.
The PSI list can be read from the xhci supported protocol extended
capabilities.
The PSI values will be used to create a USB 3.1 SuperSpeedPlus capability
descriptor for the xhci USB 3.1 roothub.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a device supports usb 3.1 SupeerSpeedPlus Gen2 speeds it povides
a SuperSpeedPlus device capability descriptor as a part of its
BOS descriptor. If we find one while parsing the BOS then save it
togeter with the other device capabilities found in the BOS
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
xhci 1.1 capable controllers have a new HCCPARAMS2 registers
with bits indicating support for new xhci 1.1 capabilities.
Also add support for the new xhci 1.1 bits in the config operational
opertational register that used to be reserved
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
[modified and left out parts not related to HCCPARAMS2 -Mathias]
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
USB OTG driver in isochronous mode has to set the parity of the receiving
microframe. The parity is set to even by default. This causes problems for
an audio gadget, if the host starts transmitting on odd microframes.
This fix uses Incomplete Periodic Transfer interrupt to toggle between
even and odd parity until the Transfer Complete interrupt is received.
Signed-off-by: Roman Bacik <rbacik@broadcom.com>
Reviewed-by: Abhinav Ratna <aratna@broadcom.com>
Reviewed-by: Srinath Mannam <srinath.mannam@broadcom.com>
Signed-off-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Even when DWC2 is in (internal) suspended state, it should disable PHY
in suspend and then enable it in resume. This patch fixes unbalanced PHY
control sequence.
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During typical gadget operation, dwc2 clock was enabled 3 times: from
dwc2_gadget_init(), dwc2_hsotg_udc_start() and dwc2_hsotg_pullup(), and
then disabled in s3c_hsotg_pullup(), s3c_hsotg_udc_stop() and
dwc2_hsotg_remove(). This really makes no sense, so leave clock control
code only in dwc2_gadget_init/remove functions.
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch removes doubled call to dwc2_hsotg_of_probe() function.
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When dwc2_hsotg_handle_unaligned_buf_complete() hs_req->req.buf
already destroyed, in dwc2_hsotg_unmap_dma(), it touches
hs_req->req.dma again, so dwc2_hsotg_unmap_dma() should be called
before dwc2_hsotg_handle_unaligned_buf_complete(). Otherwise, it
will cause a bad_page BUG, when allocate this memory page next
time.
This bug led to the following crash:
BUG: Bad page state in process swapper/0 pfn:2bdbc
[ 26.820440] page:eed76780 count:0 mapcount:0 mapping: (null) index:0x0
[ 26.854710] page flags: 0x200(arch_1)
[ 26.885836] page dumped because: PAGE_FLAGS_CHECK_AT_PREP flag set
[ 26.919179] bad because of flags:
[ 26.948917] page flags: 0x200(arch_1)
[ 26.979100] Modules linked in:
[ 27.008401] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W3.14.0 #17
[ 27.041816] [<c010e1f8>] (unwind_backtrace) from [<c010a704>] (show_stack+0x20/0x24)
[ 27.076108] [<c010a704>] (show_stack) from [<c087eea8>] (dump_stack+0x70/0x8c)
[ 27.110246] [<c087eea8>] (dump_stack) from [<c01ce0b8>] (bad_page+0xfc/0x12c)
[ 27.143958] [<c01ce0b8>] (bad_page) from [<c01ce65c>] (get_page_from_freelist+0x3e4/0x50c)
[ 27.179298] [<c01ce65c>] (get_page_from_freelist) from [<c01ce9a0>] (__alloc_pages_nodemask)
[ 27.216296] [<c01ce9a0>] (__alloc_pages_nodemask) from [<c01cf00c>] (__get_free_pages+0x20/)
[ 27.252326] [<c01cf00c>] (__get_free_pages) from [<c01e5bec>] (kmalloc_order_trace+0x34/0xa)
[ 27.288295] [<c01e5bec>] (kmalloc_order_trace) from [<c0203304>] (__kmalloc+0x40/0x1ac)
[ 27.323751] [<c0203304>] (__kmalloc) from [<c052abc0>] (dwc2_hsotg_ep_queue.isra.12+0x7c/0x1)
[ 27.359937] [<c052abc0>] (dwc2_hsotg_ep_queue.isra.12) from [<c052af88>] (dwc2_hsotg_ep_queue)
[ 27.397478] [<c052af88>] (dwc2_hsotg_ep_queue_lock) from [<c0554110>] (rx_submit+0xfc/0x164)
[ 27.433619] [<c0554110>] (rx_submit) from [<c05546e8>] (rx_complete+0x22c/0x230)
[ 27.468872] [<c05546e8>] (rx_complete) from [<c052b528>] (dwc2_hsotg_complete_request+0xfc/0)
[ 27.506240] [<c052b528>] (dwc2_hsotg_complete_request) from [<c052bba0>] (dwc2_hsotg_handle_o)
[ 27.545401] [<c052bba0>] (dwc2_hsotg_handle_outdone) from [<c052be70>] (dwc2_hsotg_epint+0x2c)
[ 27.583689] [<c052be70>] (dwc2_hsotg_epint) from [<c052c750>] (dwc2_hsotg_irq+0x1dc/0x4ac)
[ 27.621041] [<c052c750>] (dwc2_hsotg_irq) from [<c01682e0>] (handle_irq_event_percpu+0x70/0x)
[ 27.659066] [<c01682e0>] (handle_irq_event_percpu) from [<c01684ec>] (handle_irq_event+0x4c)
[ 27.697322] [<c01684ec>] (handle_irq_event) from [<c016bae0>] (handle_fasteoi_irq+0xc8/0x11)
[ 27.735451] [<c016bae0>] (handle_fasteoi_irq) from [<c0167b8c>] (generic_handle_irq+0x30/0x)
[ 27.773918] [<c0167b8c>] (generic_handle_irq) from [<c0167ca4>] (__handle_domain_irq+0x84/0)
[ 27.812018] [<c0167ca4>] (__handle_domain_irq) from [<c01003b0>] (gic_handle_irq+0x48/0x6c)
[ 27.849695] [<c01003b0>] (gic_handle_irq) from [<c010b340>] (__irq_svc+0x40/0x50)
[ 27.886907] Exception stack(0xc0d01ee0 to 0xc0d01f28)
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Jeffy Chen <jeffy.chen@rock-chips.com>
Signed-off-by: Yunzhi Li <lyz@rock-chips.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Controller enters hibernation through suspend interrupt on
disconnection. On connection, session request interrupt is generated.
dwc2 must exit hibernation and restore state from this interrupt
before continuing.
In host mode, exit from hibernation is handled by bus_resume function.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If system is loaded, reset, enum-done and setup interrupts can occur
at the same time. Current interrupt handling sequence will handle
setup packet's interrupt before handling reset interrupt. Which will
break the enumeration process. Correct sequence is to handle reset,
enum-done and then any other endpoint interrupts.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When disconnecting cable, controller will detect a suspend condition
and enter partial power down. If vbus_session is called by the phy
driver during hibernation, make sure controller exit hibernation
before it is accessed.
Signed-off-by: Jianqiang Tang <jianqiang.tang@intel.com>
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
idstschng interrupt should not be used when id pin control is
external. This is already handled on dwc2 host part. Fix it on gadget
part as well.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
There is a 200ms guard period to avoid unnecessary resets of the dwc2
ip. This delay sometimes prove to be too large when usbcv is run with
an ehci host. dwc2 only needs to be reset after addressed state.
Change the logic to reset ip after addressed state.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Make sure there are no requests pending on ep0 before reinitializing
core. Otherwise, dwc2_hsotg_enqueue_setup will fail afterwards.
Also, take hsotg->lock before calling
dwc2_hsotg_core_init_disconnected() from dwc2_conn_id_status_change()
as dwc2_hsotg_complete_request() expect lock to be held.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If the request being dequeued is already started, disable endpoint
to stop the transfer and then call dwc2_hsotg_complete_request().
Endpoint will be re-enabled on next call to dwc2_hsotg_start_req().
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
wIndex field was missing. Also print in natural order instead of
Req first, so that its easier to compare for example against
bus analyzer logs.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
dwc2_hsotg_start_req starts a request only if endpoint is not stalled.
Ignore this check for ep0 as core will clear DOEPCTL0.Stall after
sending stall handshake. Prepare instead for receiving next setup
packet.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No point of continue with initialization if core is not in a sane
state.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some device may have external id pin control enabled, so op_state
will not be set on id pin interrupt change.
Thus, ensure op_state is set to peripheral during vbus detection.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Modifying the pullup state during host mode trig a new enumeration
of attached device. Thus, avoid modifying pullup in host mode.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If dual role configuration is not selected, check and force dr_mode
based on the selected configuration.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Most of USB functions place new line after attribute value.
Let's follow this convention also in source sink function
as it improves readability.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Most of USB functions place new line after attribute value.
Let's follow this convention also in loopback function
as it improves readability.
Signed-off-by: Krzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
While building allmodconfig on avr32 the build failed with the error:
"at91_pmc_base" [drivers/usb/gadget/udc/atmel_usba_udc.ko] undefined!
On checking the code it turned out that if CONFIG_OF is defined then it
is using at91_pmc_read() which is using at91_pmc_base. And unless
COMMON_CLK_AT91 is defined we donot have at91_pmc_base. And
COMMON_CLK_AT91 is available with AT91 architecture.
Mention the dependency such that this driver builds with avr32 only if
OF is not enabled.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A NULL comparison can be written as if (var) or if (!var).
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rearrange the udc_basic_init function to remove the forward declaration.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove the forward declarations of udc_pci_probe and udc_pci_remove.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rearrange udc_free_dma_chain to remove the forward declaration. While at
it fixed all the relevant checkpatch warnings.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rearrange udc_create_dma_chain to remove the forward declaration. While
rearranging fixed the relevant checkpatch warnings.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rearrange the udc_remote_wakeup function to remove the forward
declaration.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Rearrange the udc_probe function to remove the forward declarations.
While rearranging also fixed the relevant checkpatch warnings.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The condition checking for irq_registered, regs, mem_region and active
are not required as this is the remove function. And we are in the
remove means that probe was successful and they can never be NULL at
this point of code.
It was required in the original code as the remove function was part of
the error handler of probe function.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We have the function free_dma_pools() which frees all the dma pools. Use
it instead of calling all the functions separately. The if conditions
for data_requests and stp_requests are also not required here as this is
the remove function and we are here means probe has succeeded and dma
has been successfully allocated, so they cannot be NULL here.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Use WARN_ON() instead of halting the kernel with BUG_ON() and also fix
the checkpatch warning.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Handle the error properly instead of calling the pci remove function.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
A rewrite of init_dma_pools() with proper error handling.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
ID status change interrupt will not be handled in peripheral only
configuration. So initialize op_state during gadget init.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Correctly update lx_state on gadget connection and disconnection.
When usb cable is disconnected, lx_state must be updated to L3 as
controller could be in power off state.
When usb cable is connected, lx_state must be updated to L0 as
controller is powered.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On a disconnect, dwc2 will kill all remaining urbs from qh list.
urbs are given back to hcd with -ETIMEDOUT status.
Some usb device driver, like mass storage, will unlink all urbs
using usb_hcd_unlink_urb when receiving a negative status different
from -ECONNRESET.
The following flow will then happen:
dwc2_hcd_disconnect()
-> dwc2_kill_all_urbs() try to kill first pending urb.
-> dwc2_host_complete(-ETIMEDOUT)
-> usb_hcd_giveback_urb(-ETIMEDOUT)
-> sg_complete()
-> usb_unlink_urb()
-> usb_put_dev(urb->dev)
-> dwc2_kill_all_urbs() try to kill next pending urb.
-> dwc2_host_complete(-ETIMEDOUT)
-> usb_hcd_giveback_urb(-ETIMEDOUT)
-> NULL pointer dereferencing because urb->dev has been freed for all
urbs of this device.
The root cause of this NULL pointer is to call call usb_unlink_urb()
while we are killing all urbs. To avoid this return urb with
-ECONNRESET status
This issue usually happens while removing mass storage device during
transfer.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
On first qh initialization, hsotg->frame_number is not corresponding
to reality. So read it from host controller to get correct value.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Print urb->iso_frame_desc.status after it has been updated using
dwc2_hcd_urb_get_iso_desc_status().
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Some high speed mass storage devices fail to enumerate with following
error:
Cannot enable port %i. Maybe the USB cable is bad?
This happens only when the device is plugged while the controller
is in hibernation state. After exiting hibernation, the controller
detects the device as a low speed device and fail to enumerate it.
Problem occurs only if HPRT0.PWR bit is programmed in a too short
delay after exiting hibernation. Dumping hprt register in
_dwc2_hcd_resume() directly after dwc2_exit_hibernation() shows that
HPRT0.LNSTS (D+/D- level) becomes valid approximately 2ms after
exiting hibernation.
Since dwc2_exit_hibernation() is called from atomic context, move the
delay out of this function.
Delay value is experimental and not mentioned in Synopsys
documentation. To be on the safe side 3ms delay is used.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If an interrupt rises during hibernation process, dwc2 will assert
interrupt line to interrupt controller. If interrupt is level
sensitive, interrupt handler will be called in a loop because dwc2
will not be able to clear it while controller is hibernated.
Thus, clear all controller interrupts before hibernation entry.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disable host interrupts before synchronising dwc2 irq.
So that interrupts are not generated once controller is stopped.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
GINTSTS.DisconnInt is host only interrupt and should be disable after
dwc2_disable_host_interrupts is called.
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
In case controller is asked to stop while devices are connected,
disconnect all devices and clean up before stopping.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Frame number is reset in hardware after exiting hibernation.
Thus, reset frame_number and ensure qh are queued with correct
sched_frame.
Otherwise, qh->sched_frame may be too high compared to
current frame number (which is 0). This can delay addition of qh in
the list of transfers until frame number reaches qh->sched_frame.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Port can be resumed in bus_resume callback.
In this case, there is no need to drive resume a second time
when hcd ask for it.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If hibernation is supported, resume of devices will be handled in
bus_resume callback.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When a device is disconnected, lx_state must not be changed since the
device may be disconnected whereas controller is still powered.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
During hcd initialization, hardware accessible flag and lx_state must
be reset to the working state since controller is powered at this stage.
Same logic applied for stop callback.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Disable controller power and enter hibernation when usb bus is
suspended. A phy driver is required to disable the power of the
controller and detect remote-wakeup or disconnection since the
controller will not be able to detect these in this state.
Once the phy driver detects bus activity, it must call
usb_hcd_resume_root_hub.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
lx_state must be used to reflect controller power state only and not
bus state. Thus add a flag to track state during bus suspend.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
port resume sequence may be used in different places. Create a
function to handle it. Make hprt0 read-modify-write atomic and
clear HPRT0_SUSP for both writes as it is a "read, write-set,
and self-clear (R_WS_SC)" bit. Since the lock is released
between the writes, read hprt0 again.
Since the phy clock is stopped in dwc2_port_suspend(), enable it
here and remove the PCGCTL write from dwc2_hcd_hub_control()
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
When entering hibernation hprt0 must be read using dwc2_read_hprt0().
Otherwise, any set hprt0 status bits will be cleared when restoring
hprt0 on exit from hibernation.
Signed-off-by: Gregory Herrero <gregory.herrero@intel.com>
Signed-off-by: Mian Yousaf Kaukab <yousaf.kaukab@intel.com>
Tested-by: Robert Baldyga <r.baldyga@samsung.com>
Tested-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Remove v4l2 stuff - v4l2_buf, v4l2_plane - from struct vb2_buffer.
Add new member variables - bytesused, length, offset, userptr, fd,
data_offset - to struct vb2_plane in order to cover all information
of v4l2_plane.
struct vb2_plane {
<snip>
unsigned int bytesused;
unsigned int length;
union {
unsigned int offset;
unsigned long userptr;
int fd;
} m;
unsigned int data_offset;
}
Replace v4l2_buf with new member variables - index, type, memory - which
are common fields for buffer management.
struct vb2_buffer {
<snip>
unsigned int index;
unsigned int type;
unsigned int memory;
unsigned int num_planes;
struct vb2_plane planes[VIDEO_MAX_PLANES];
<snip>
};
v4l2 specific fields - flags, field, timestamp, timecode,
sequence - are moved to vb2_v4l2_buffer in videobuf2-v4l2.c
struct vb2_v4l2_buffer {
struct vb2_buffer vb2_buf;
__u32 flags;
__u32 field;
struct timeval timestamp;
struct v4l2_timecode timecode;
__u32 sequence;
};
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Make videobuf2-v4l2 as a wrapper of videobuf2-core for v4l2-use.
And replace videobuf2-core.h with videobuf2-v4l2.h.
This renaming change should be accompanied by the modifications
of all device drivers that include videobuf2-core.h.
It can be done with just running this shell script.
replace()
{
str1=$1
str2=$2
dir=$3
for file in $(find $dir -name *.h -o -name *.c -o -name Makefile)
do
echo $file
sed "s/$str1/$str2/g" $file > $file.out
mv $file.out $file
done
}
replace "videobuf2-core" "videobuf2-v4l2" "include/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/media/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/usb/gadget/"
replace "videobuf2-core" "videobuf2-v4l2" "drivers/staging/media/"
Signed-off-by: Junghak Sung <jh1009.sung@samsung.com>
Signed-off-by: Geunyoung Kim <nenggun.kim@samsung.com>
Acked-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Acked-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This patch adds a compatible string to support for R-Car H3.
Since the HS-USB controller of R-Car H3 is almost the same specification
with R-Car Gen2 (these have 16 pipes and usb-dmac), this patch
sets the "type" of renesas_usbhs_driver_param to USBHS_TYPE_RCAR_GEN2.
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch fixes the following warning if 64-bit architecture environment:
./drivers/usb/renesas_usbhs/common.c:496:25: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
dparam->type = of_id ? (u32)of_id->data : 0;
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
If dma_pool_alloc() fails we are jumping to fail and releasing all the
bd_tables which have been added to the chain but we missed freeing this
bd_table which was just allocated and still not added to the chain of
bd_table.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
We *know* our threads executes with our IRQs
disabled. We really don't need to use the _irqsave()
variant of spin_lock().
Signed-off-by: Felipe Balbi <balbi@ti.com>
Instead of limiting __dwc3_gadget_kick_transfer() to
Xfer Complete, we can try to issue Update Transfer
command from Xfer In Progress too.
Signed-off-by: Felipe Balbi <balbi@ti.com>
If we get a Xfer Not Ready event with reason
"Transfer Active" it means endpoint is still
transferring data and we can use that to issue
update transfer for this particular endpoint
in case we have pending requests in our queue.
Signed-off-by: Felipe Balbi <balbi@ti.com>
if by the time we get to XFER_COMPLETE we have
pending requests to be processed, instead of waiting
for a following XFER_NOT_READY, let's start the request
right away and, maybe, save the time of a few NAKs
due to lack of started transfers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
gadget methods should be called without
spinlocks held.
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Sharing the ACPI companion with dwc3 core so it has access
to the properties defined for DWC3 in ACPI tables.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
No functional affect on existing platforms, but the driver
is now ready to extract the properties also from ACPI tables
as well as from DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
of_usb_get_dr_mode will be converted into more generic
usb_get_dr_mode function that will take struct device
instead of struct device_node as its parameter.
To make the conversion possible later, waiting for the
platform device for dwc3 to be populated before calling
of_usb_get_dr_mode.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
By using the unified device property interface, the function
can be made available for all platforms and not just the
ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of tcm, ep->driver_data was used only for endpoint claiming so
we can simplify code by reducing it. We also remove give_back_ep()
function which is not needed after all - when error code is returned
from bind() function, composite will release all endpoints anyway.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of dbgp, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of u_serial ep->driver_data stores pointer to struct gs_port,
which is referenced in many places in code. Code using ep->driver_data
to mark endpoint as enabled/disabled has been removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of u_ether we only need to store in ep->driver_data pointer to
struct eth_dev, as it's used in rx_complete() and tx_complete() callbacks.
All other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_uvc, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_uac2, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_uac1, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_subset, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_sourcesink we only need to store in ep->driver_data pointer
to struct f_sourcesink, as it's used in source_sink_complete() callback.
All other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_serial, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_rndis, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_printer we only need to store in ep->driver_data pointer to
struct printer_dev, as it's used in rx_complete() and tx_complete()
callbacks. All other uses of ep->driver_data are now meaningless and can
be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_phonet we only need to store in ep->driver_data pointer to
struct f_phonet, as it's used in pn_tx_complete() and pn_rx_complete()
callbacks. All other uses of ep->driver_data are now meaningless and can
be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_obex, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_ncm, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_midi we only need to store in ep->driver_data pointer to
struct f_midi, as it's used in f_midi_complete() callback and related
functions. All other uses of ep->driver_data are now meaningless and
can be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_mass_storage we only need to store in ep->driver_data
pointer to struct fsg_common, which is used in bulk_in_complete() and
bulk_out_complete() callbacks. All other uses of ep->driver_data are now
meaningless and can be safely removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_hid we only need to store in ep->driver_data pointer to
struct f_loopback, as it's used in loopback_complete() callback. All
other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_hid we only need to store in ep->driver_data pointer to
struct f_hidg, as it's used in f_hidg_req_complete() callback. All
other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_ecm, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_acm we only need to store in ep->driver_data pointer to
struct f_acm, as it's used in acm_complete_set_line_coding() callback.
All other uses of ep->driver_data are now meaningless and can be safely
removed.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since ep->driver_data is not used for endpoint claiming, neither for
enabled/disabled state storing, we can reduce number of places where
we read or modify it's value, as now it has no particular meaning for
function or framework logic.
In case of f_ecm, ep->driver_data was used only for endpoint claiming
and marking endpoints as enabled, so we can simplify code by reducing
it.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch introduces usb_ep_autoconfig_release() function which allows
to release endpoint previously obtained from usb_ep_autoconfig() during
USB function bind.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The 'driver_data' field in ep0 is never set to pointer to cdev, so we
have to obtain it from another source as in this context ep->driver_data
contains invalid data.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Fix comments in code to make them up to date.
composite: claiming endpoint is now done by setting ep->claimed flag,
not ep->driver_data.
epautoconf: usb_ep_autoconfig() and usb_ep_autoconfig_ss() return
claimed endpoint with ep->claimed flag already set.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The millisecond of the last second will be normal if tv_sec is
overflowed. But for y2038 consistency and demonstration purpose,
and avoiding further risks, we need to remove 'timeval' in this
driver, to avoid similair problems.
Signed-off-by: Pingbo Wen <pingbo.wen@linaro.org>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add support for USB DRVVBUS pinctrl state change during
suspend/resume. This helps is conserving power during
system sleep.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Since the host and gadget can't agree with transfer length before
each transfer, but they agree with max packet size for each
endpoint, we use max packet size to format data pattern.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
With this change, the host and gadget doesn't need to agree with transfer
length for comparing the data, since they doesn't know each other's
transfer size, but know max packet size.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
(Fixed the 'line over 80 characters warning' by Peter Chen)
Tested-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Using the same data format "buf[j] = (u8)(i + j)" among
write, compare buf, and console output stage.
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
The element of urbs array will be initialized at below code
at once.
for (i = 0; i < param->sglen; i++) {
urbs[i] = iso_alloc_urb(udev, pipe, desc,
param->length, offset);
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Allocate the size of urb pointer array according to testusb's
parameter sglen, and limits the length of sglen as MAX_SGLEN
(128 currently).
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
This patch switches calls to readl/writel to their
dwc2_readl/dwc2_writel equivalents which preserve platform endianness.
This patch is necessary to access dwc2 registers correctly on big-endian
systems such as the mips based SoCs made by Lantiq. Then dwc2 can be
used to replace ifx-hcd driver for Lantiq platforms found e.g. in
OpenWrt.
The patch was autogenerated with the following commands:
$EDITOR core.h
sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h
sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h
Some files were then hand-edited to fix checkpatch.pl warnings about
too long lines.
Signed-off-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
USB network adapters support Jumbo frames. The only thing blocking
that feature is the code in the gadget driver that disposes of
packets larger than 1518 bytes, and the limit on the ioctl to set
the mtu.
This patch relaxes these limits, and allows up to 15k frames sizes.
The 15k value was chosen because 16k does not work on all platforms,
and usingclose to 16k will result in allocating 5 or 8 4k pages to
store the skb, wasting pages at no measurable performance gain.
On a topic-miami board (Zynq-7000), iperf3 performance reports:
MTU= 1500, PC-to-gadget: 139 Mbps, Gadget-to-PC: 116 Mbps
MTU=15000, PC-to-gadget: 239 Mbps, Gadget-to-PC: 361 Mbps
On boards with slower CPUs the performance improvement will be
relatively much larger, e.g. an OMAP-L138 increased from 40 to
220 Mbps using a similar patch on an 2.6.37 kernel.
Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: Felipe Balbi <balbi@ti.com>
struct at91_udc_data is now only used inside the driver, move it to its
include.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
this driver has long ago became dwc2.ko with
both peripheral and host roles, there's no point
in keeping the old function names.
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Add adjust_frame_length_quirk for writing to fladj register
which adjusts (micro)frame length to value provided by
"snps,quirk-frame-length-adjustment" property thus avoiding
USB 2.0 devices to time-out over a longer run
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
[un]register_interest and reading cable state by
name have been deprecated. Switch to new API.
Signed-off-by: Ivan T. Ivanov <ivan.ivanov@linaro.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
