This patch adds NOR Flash, LEDs and PIB support for MPC8568E-MDS
boards. Plus, move bcsr node into localbus node, and add bcsr5
gpio-controller node.
Some platform code modifications were also needed.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the MSI section to the DTS file for the GE PPC9A.
Signed-off-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Support for the SBC610 VPX Single Board Computer from GE (PowerPC MPC8641D).
This patch adds basic support for the on-board flash.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the MSI section to the DTS file for the GE SBC610.
Signed-off-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Correction to interrupt map mask for GE SBC310 XMC site and addition of
alias.
Signed-off-by: Malcolm Crossley <malcolm.crossley2@gefanuc.com>
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add the MSI section to the DTS file for the GE SBC310.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The DIU driver should bind against "fsl,mpc5121-diu"
directly. Add this compatible property to the match
table and fix DTS and platform code accordingly.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Collects several changes needed after applying
previous mpc5121 platform and driver patches:
- Add mpc5121 reset module node
- Clean up and fix NAND description, remove unused properties
here and correct NAND flash chip size.
- Clean up I2C nodes: remove obsolete "cell-index" properties,
add "fsl,preserve-clocking" property
- Add I2C RTC node for m41t61 RTC
- Add I2C nodes for AD7414 temperature sensor and AT24C32CD3 EEPROM
- Fix compatible property in DMA node
- Clean up CAN nodes, remove unused "cell-index" properties
- Fix compatible property in DIU node
- USB node changes:
- use "fsl,mpc5121-usb2-dr" compatible property only
- remove "port0" and "port1" properties as these are only used
for multi-port host(MHP) module which is not available
on MPC5121.
- use 'fsl,invert-drvvbus' and 'fsl,invert-pwr-fault' in
USB node for internal PHY to specify polarities
of the appropriate port pins.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Detlev Zundel <dzu@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sync Glacier dts with latest Canyonlands version:
- Add l2 cache support
- Add NDFC support
- Add RTC support
- Add AD7414 hwmon support
- Change EMAC compatible node from emac4 to emac4sync and correct the
register size
- Add support for ISA holes on 4xx PCI/X/E
(as done in Benjamin Herrenschmidt's patch for Canyonlands)
- Add Crypto device node
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds NOR FLASH MTD support to the Katmai (440SPe) dts file.
For this the OPB ranges address is mapped differently (base 0x00000000
-> 0xe0000000). This results in the address being identical to the lower
32bit of its physical address. This is needed for the MTD mapping to work
correctly, since U-Boot will insert the physical addresses of the EBC
chip selects into the EBC ranges property. This is the way its done in
most other 4xx dts files as well.
Additionally with a small whitespace cleanup.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
* 'next' of git://git.secretlab.ca/git/linux-2.6: (23 commits)
powerpc: fix up for mmu_mapin_ram api change
powerpc: wii: allow ioremap within the memory hole
powerpc: allow ioremap within reserved memory regions
wii: use both mem1 and mem2 as ram
wii: bootwrapper: add fixup to calc useable mem2
powerpc: gamecube/wii: early debugging using usbgecko
powerpc: reserve fixmap entries for early debug
powerpc: wii: default config
powerpc: wii: platform support
powerpc: wii: hollywood interrupt controller support
powerpc: broadway processor support
powerpc: wii: bootwrapper bits
powerpc: wii: device tree
powerpc: gamecube: default config
powerpc: gamecube: platform support
powerpc: gamecube/wii: flipper interrupt controller support
powerpc: gamecube/wii: udbg support for usbgecko
powerpc: gamecube/wii: do not include PCI support
powerpc: gamecube/wii: declare as non-coherent platforms
powerpc: gamecube/wii: introduce GAMECUBE_COMMON
...
Fix up conflicts in arch/powerpc/mm/fsl_booke_mmu.c.
Hopefully even close to correctly.
Add a device tree source file for the Nintendo Wii video game console.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a device tree source file for the Nintendo GameCube video game console.
Signed-off-by: Albert Herranz <albert_herranz@yahoo.es>
Acked-by: Segher Boessenkool <segher@kernel.crashing.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Newer revs of the FPGA have a larger SD buffer.
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add nodes for PPC440SPe DMA, I2O, XOR engines and Memory
Queue module which are used in the updated PPC440SPe ADMA
driver. Also extend plb ranges property to specify address
ranges for DMA0/1 and I2O engines.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
- Add nodes for PMC and GTM controllers. GTM4 can be used as a wakeup
source;
- Add fsl,magic-packet properties to eTSEC nodes, i.e. wake-on-lan
support. Unlike MPC8313 processors, MPC8315 can resume from deep
sleep upon magic packet reception.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Describe all LocalBus chipselects on MPC8349E-MITX board. Also add flash
bindings.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add OF descriptions of EEPROM, two GPIO extenders and SPD hanging on I2C
on this board.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
mpc8349 bears two GPIO controllers. Enable support for them.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The stanza for PCI was copied from Bamboo which has four PCI slots. Yosemite
only has one PCI slot which is mapped to IDSEL 12, ADDR 22, IRQ2 Vector 25,
INTA.
Signed-off-by: Curtis Wald <cwald@watchguardvideo.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Set PCI-E node inbound DMA ranges size to 4GB for correct boot up of Katmai.
Signed-off-by: Pravin Bathija <pbathija@amcc.com>
Acked-by: Feng Kan <fkan@amcc.com>
Acked-by: Prodyut Hazarika <phazarika@amcc.com>
Acked-by: Loc Ho <lho@amcc.com>
Acked-by: Tirumala Reddy Marri <tmarri@amcc.com>
Acked-by: Victor Gallardo <vgallardo@amcc.com>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add basic support for the P4080 DS reference board. None of the data
path devices (ethernet, crypto, pme) are support at this time.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for NVRAM on GE Fanuc's PPC9A.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Add support for NVRAM on GE Fanuc's SBC310.
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch enables the NVRAM found on the GE Fanuc SBC610
Signed-off-by: Martyn Welch <martyn.welch@gefanuc.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Simply add power management controller nodes and sleep properties.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch adds needed nodes and properties to support suspend/resume
on the MPC8610HPCD boards.
There is a dedicated switch (SW9) that is used to wake up the boards.
By default the SW9 button is routed to IRQ8, but could be re-routed
(via PIXIS) to sreset.
With 'no_console_suspend' kernel command line argument specified, the
board is also able to wakeup upon serial port input.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com> [dts]
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add power management controller nodes;
- Add interrupts for RTC nodes, the RTC interrupt may be used as a
wakeup source;
- Add sleep properties (DEVDISR bit mask) and sleep-nexus nodes.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
P1020 is another member of Freescale QorIQ series of processors.
It is an e500 based dual core SOC.
Being a scaled down version of P2020 it has following differences from P2020:
- 533MHz - 800MHz core frequency.
- 256Kbyte L2 cache
- Ethernet controllers with classification capabilities(new controller).
From board perspective P1020RDB is same as P2020RDB.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch creates the dts files for each core and splits the devices
between the two cores for P2020RDB.
core0 has memory, L2, i2c, spi, dma1, usb, eth0, eth1, crypto,
global-util, pci0,
core1 has L2, dma2, eth0, pci1, msi.
MPIC is shared between two cores but each core will protect its
interrupts from other core by using "protected-sources" of mpic.
Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
u-boot partition size should be 0x80000 (512 KB), not 0x8000 (32 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This patch fixes USB GPIOs numbers for MPC8569E-MDS boards, plus
according to the latest HW Getting Started Guide (rev 3.3, pilot
boards), USB "POWER" GPIO polarity has changed, it is no longer
inverted.
This patch makes USB Host somewhat work on pilot boards, though
there are still some problems with determining devices speed and
long bulk transfers.
Reported-by: Liu Yu <Yu.Liu@freescale.com>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI-e addressing was originally patterned of the MPC8548CDS
which has PCI1, PCI2, and PCI-e. Since this board only has
PCI1 and PCI-e, it makes more sense to be similar to the MPC8568MDS
board. This does that by cutting the PCI/PCI-e I/O sizes from
16MB to 8MB and pulling the PCI-e I/O range back to 0xe280_0000
(the hole where PCI2 I/O would have been).
This also fixes a typo where an extra zero made an 8MB range a 128MB
range, removes the hole left by PCI2 from the aliases, and sets the
clocks to match the oscillators that are actually on the board.
With accompanying u-boot updates, PCI-e has been validated with
both a sky2 card (1148:9e00) and an e1000 card (8086:108b).
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Additionally to increasing #size-cells to in the root node, we also
need to explicitly define the ranges property in the plb node, because
of the different #size-cells between child and parent.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Adding tx/rx-fifo-size-gige to EMAC fields for evaluation kit DTS
files where appropriate.
Signed-off-by: Dave Mitchell <dmitchell@appliedmicro.com>
Acked-by: Prodyut Hazarika <phazarika@appliedmicro.com>
Acked-by: Victor Gallardo <vgallardo@appliedmicro.com>
Acked-by: Loc Ho <lho@appliedmicro.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The 'fsl5200-clocking'-property was dropped since
0d1cde2358. Remove all occurences
in dts-files.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
- serial Console on PSC1
- 64MB SDRAM
- MTD CFI Flash
- Ethernet FEC
- IDE support
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
- serial Console on PSC1
- 64MB SDRAM
- MTD CFI Flash
- Ethernet FEC
- I2C with PCF8563 and Temp. Sensor ADM9240
- IDE support
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
eSDHC block in MPC837x SOCs reports inverted write-protect state, soon
sdhci-of driver will look for sdhci,wp-inverted properties to decide
whether apply a specific quirk.
So, document the property and add it to device tree source files.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Pierre Ossman <pierre@ossman.eu>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: David Vrabel <david.vrabel@csr.com>
Cc: Ben Dooks <ben@fluff.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the ESTeem 195E Hotfoot SBC.
There are several variants of the SBC deployed, single/dual
ethernet+serial, and also 4MB/8MB flash variations. In the interest of
having a single kernel image boot on all boards, the cuboot shim detects
the differences and mangles the DTS tree appropriately.
With the exception of the CF interface that was never populated on
production boards, this code/DTS supports all boardpop options.
Signed-off-by: Solomon Peachy <solomon@linux-wlan.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds support for the AMCC (AppliedMicro) PPC460SX Eiger evaluation
board.
Signed-off-by: Tai Tri Nguyen <ttnguyen@amcc.com>
Acked-by: Feng Kan <fkan@amcc.com>
Acked-by: Tirumala Marri <tmarri@amcc.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds some nodes to the AMCC Arches dts:
- L2 cache support
- NOR FLASH mapping with default partitioning
- I2C HWMON device (AD7414)
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
- Add gpio-controller node for BCSR17, it is used to control USB
speed and VBUS;
- Add timer node for QE GTM, needed for USB host;
- Add usb node itself;
- Add some probing code for BCSR GPIOs.
NOTE: QE USB doesn't work on prototype boards, but should work on
pilot boards if specs and schematics are correct, though we
don't have the pilot boards to actually test it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
- Add usb node;
- Configure pins and clocks;
- Enable USB function in BCSR.
The support was successfully tested using serial and ethernet gadget
drivers.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
