Duty Cycle Correction(DCC) needs to be enabled if the MPU is to run at
frequencies beyond 1.4GHz for OMAP5, DRA75x, DRA72x.
MPU DPLL has a limitation on the maximum frequency it can be locked
at. Duty Cycle Correction circuit is used to recover a correct duty
cycle for achieving higher frequencies (hardware internally switches
output to M3 output(CLKOUTHIF) from M2 output (CLKOUT)).
For further information, See the note on OMAP5432 Technical Reference
Manual(SWPU282U) chapter 3.6.3.3.1 "DPLLs Output Clocks Parameters",
and also the "OMAP543x ES2.0 DM Operating Conditions Addendum v0.5"
chapter 2.1 "Micro Processor Unit (MPU)". Equivalent information is
present in relevant DRA75x, 72x documentation(SPRUHP2E, SPRUHI2P).
Signed-off-by: Andrii Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Taras Kondratiuk <taras@ti.com>
Signed-off-by: J Keerthy <j-keerthy@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
[t-kristo@ti.com: added TRM / DM references for DCC clock rate]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2430 I2CHS modules require specific hardware ops to be used, so added
a new compatible string for this.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
OMAP2 has slightly different DPLL compared to later OMAP generations.
This patch adds support for the ti,omap2-dpll-core-clock and also adds
the bindings documentation.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
At least the smc91x driver expects the device to be at 0x300
offset from bus base address. This does not work currently
for GPMC when booted in device tree mode as it attempts to
remap the the allocated GPMC partition to the address
configured by the device tree plus the device offset.
Note that this works just fine when booted with legacy mode.
Let's fix the issue by just ignoring any device specific
offset while remapping. And let's make sure the remap
address confirms to the GPMC 16MB minimum granularity
as listed in the TRM for GPMC_CONFIG7 BASEADDRESS bits.
Otherwise we can get something like this:
omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
If gpmc_cs_remap() fails we will get an error because we are calling
release_resource() on an uninitialized resource. Let's fix that by
checking the resource flags. And while at it, let's also make
gpmc_cs_delete_mem() use the res pointer that we already have to
avoid confusion.
Without this patch we can get the following error:
omap-gpmc 6e000000.gpmc: cannot remap GPMC CS 1 to 0x01000300
Unable to handle kernel NULL pointer dereference at virtual address 00000018
...
(gpmc_cs_free+0x94/0xc8)
(gpmc_probe_generic_child+0x178/0x1ec)
(gpmc_probe_dt+0x1bc/0x2cc)
(gpmc_probe+0x250/0x44c)
(platform_drv_probe+0x3c/0x6c)
(really_probe+0x74/0x208)
(driver_probe_device+0x34/0x50)
(bus_for_each_drv+0x60/0x8c)
(device_attach+0x80/0xa4)
(bus_probe_device+0x88/0xb0)
(device_add+0x320/0x450)
(of_platform_device_create_pdata+0x80/0x9c)
(of_platform_bus_create+0xd0/0x170)
(of_platform_bus_create+0x12c/0x170)
(of_platform_populate+0x60/0x98)
(pdata_quirks_init+0x30/0x48)
(customize_machine+0x20/0x48)
(do_one_initcall+0x2c/0x14c)
(do_basic_setup+0x98/0xd8)
(kernel_init_freeable+0x12c/0x1e0)
(kernel_init+0x8/0xf0)
(ret_from_fork+0x14/0x2c)
Code: e1a04000 e59f0070 eb195136 e5942010 (e5923018)
Cc: Pekon Gupta <pekon@ti.com>
Reviewed-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: tony Lindgren <tony@atomide.com>
A few OMAP hwmod and clock fixes for v3.15-rc. Probably the most useful
fix is the AM43xx DPLL patch.
Basic build, boot, and PM test results are here:
http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.15-rc/20140411130021/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TOEq
-----END PGP SIGNATURE-----
Merge tag 'for-v3.15-rc/omap-fixes-a' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.15/fixes
OMAP hwmod and clock fixes for v3.15-rc
A few OMAP hwmod and clock fixes for v3.15-rc. Probably the most useful
fix is the AM43xx DPLL patch.
Basic build, boot, and PM test results are here:
http://www.pwsan.com/omap/testlogs/prcm-fixes-a-v3.15-rc/20140411130021/
Do not try to initialize display for DT boot, since omapdss
is now initialized via Device Tree. Without this patch the
display subsystem does not properly come up.
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Bug was introduced by commit 'f92d959: ARM: OMAP2+: hwmod:
Extract no-idle and no-reset info from DT'
There were 2 versions of the patch posted which resulted in the above
commit. While v1 [1] had the bug, v2 [2] had it fixed.
However v1 apparently seemed to have been pulled in by mistake
introducing the bug.
Given of_find_property() does return NULL when the node passed is
NULL, it did not introduce any functional issues as such, just the
fact that the second if check was executed unnecessarily.
[1] https://www.mail-archive.com/linux-omap@vger.kernel.org/msg94220.html
[2] http://www.spinics.net/lists/linux-omap/msg98490.html
Cc: Nishanth Menon <nm@ti.com>
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Fixes: f92d9597f7 ("ARM: OMAP2+: hwmod: Extract no-idle and no-reset info from DT")
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On AM43xx, if a PLL is in bypass at kernel init, the code in
omap2_get_dpll_rate() will not realize this and will try to calculate
the clock rate using the multiplier and the divider, resulting in
errors.
omap2_init_dpll_parent() has similar issue.
Add the missing soc_is_am43xx() check to make the code work on AM43xx.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Sathya Prakash M R <sathyap@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
OMAP3 doesn't contain "l3_init_clkdm" clock domain. Use the
proper clock domains for USB Host and USB TLL modules.
Gets rid of the following warnings during boot
omap_hwmod: usb_host_hs: could not associate to clkdm l3_init_clkdm
omap_hwmod: usb_tll_hs: could not associate to clkdm l3_init_clkdm
Reported-by: Nishanth Menon <nm@ti.com>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Fixes: de231388cb ("ARM: OMAP: USB: EHCI and OHCI hwmod structures for OMAP3")
Cc: Keshava Munegowda <keshava_mgowda@ti.com>
Cc: Partha Basak <parthab@india.ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
There is a solitary write to this register every wakeup from off-mode,
which isn't doing anything, so remove it.
Also note that modifying this register trashes any attempted
voltage scaling configuration and the change probably should
never have gotten merged in the first place.
Cc: Nishanth Menon <nm@ti.com>
Cc: Kevin Hilman <khilman@linaro.org>
Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
[tony@atomide.com: updated comments to describe regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This contains OMAP related fbdev changes for 3.15. The bulk of the patches are
for adding Device Tree support for OMAP Display Subsystem:
* SoCs: OMAP2/3/4
* Boards: OMAP4 Panda, OMAP4 SDP, OMAP3 Beagle, OMAP3 Beagle-xM, OMAP3
IGEP0020, OMAP3 N900
* Devices: TFP410 Encoder, tpd12s015 HDMI companion chip, Sony acx565akm panel,
MIPI DSI Command mode panel and HDMI, DVI and Analog TV connectors
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=Mnc1
-----END PGP SIGNATURE-----
Merge tag 'fbdev-omap-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull OMAP fbdev changes from Tomi Valkeinen:
"This is based on the already pulled fbdev-main changes, and this also
merges .dts branch from Tony Lindgren (which has also been pulled), so
that I was able to add the display related .dts changes.
This contains OMAP related fbdev changes for 3.15. The bulk of the
patches are for adding Device Tree support for OMAP Display Subsystem:
- SoCs: OMAP2/3/4
- Boards: OMAP4 Panda, OMAP4 SDP, OMAP3 Beagle, OMAP3 Beagle-xM,
OMAP3 IGEP0020, OMAP3 N900
- Devices: TFP410 Encoder, tpd12s015 HDMI companion chip, Sony
acx565akm panel, MIPI DSI Command mode panel and HDMI, DVI and
Analog TV connectors"
* tag 'fbdev-omap-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (45 commits)
OMAPDSS: HDMI: fix interlace output
OMAPDSS: add missing __init for dss_init_ports
ARM: OMAP2+: remove pdata quirks for displays
OMAPDSS: remove DT hacks for regulators
Doc/DT: Add DT binding documentation for tpd12s015 encoder
Doc/DT: Add DT binding documentation for TFP410 encoder
Doc/DT: Add DT binding documentation for Sony acx565akm panel
Doc/DT: Add DT binding documentation for MIPI DSI CM Panel
Doc/DT: Add DT binding documentation for HDMI Connector
Doc/DT: Add DT binding documentation for DVI Connector
Doc/DT: Add DT binding documentation for Analog TV Connector
ARM: omap3-n900.dts: add display information
ARM: omap3-igep0020.dts: add display information
ARM: omap3-beagle-xm.dts: add display information
ARM: omap3-beagle.dts: add display information
ARM: omap4-sdp.dts: add display information
Doc/DT: Add DT binding documentation for OMAP DSS
OMAPDSS: acx565akm: Add DT support
OMAPDSS: connector-analog-tv: Add DT support
OMAPDSS: hdmi-connector: Add DT support
...
This time a few more updates queued up.
* Rework VT-d code to support ACPI devices
* Improvements for memory and PCI hotplug support
in the VT-d driver
* Device-tree support for OMAP IOMMU
* Convert OMAP IOMMU to use devm_* interfaces
* Fixed PASID support for AMD IOMMU
* Other random cleanups and fixes for OMAP, ARM-SMMU
and SHMOBILE IOMMU
Most of the changes are in the VT-d driver because some rework was
necessary for better hotplug and ACPI device support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=uy/Z
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU upates from Joerg Roedel:
"This time a few more updates queued up.
- Rework VT-d code to support ACPI devices
- Improvements for memory and PCI hotplug support in the VT-d driver
- Device-tree support for OMAP IOMMU
- Convert OMAP IOMMU to use devm_* interfaces
- Fixed PASID support for AMD IOMMU
- Other random cleanups and fixes for OMAP, ARM-SMMU and SHMOBILE
IOMMU
Most of the changes are in the VT-d driver because some rework was
necessary for better hotplug and ACPI device support"
* tag 'iommu-updates-v3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (75 commits)
iommu/vt-d: Fix error handling in ANDD processing
iommu/vt-d: returning free pointer in get_domain_for_dev()
iommu/vt-d: Only call dmar_acpi_dev_scope_init() if DRHD units present
iommu/vt-d: Check for NULL pointer in dmar_acpi_dev_scope_init()
iommu/amd: Fix logic to determine and checking max PASID
iommu/vt-d: Include ACPI devices in iommu=pt
iommu/vt-d: Finally enable translation for non-PCI devices
iommu/vt-d: Remove to_pci_dev() in intel_map_page()
iommu/vt-d: Remove pdev from intel_iommu_attach_device()
iommu/vt-d: Remove pdev from iommu_no_mapping()
iommu/vt-d: Make domain_add_dev_info() take struct device
iommu/vt-d: Make domain_remove_one_dev_info() take struct device
iommu/vt-d: Rename 'hwdev' variables to 'dev' now that that's the norm
iommu/vt-d: Remove some pointless to_pci_dev() calls
iommu/vt-d: Make get_valid_domain_for_dev() take struct device
iommu/vt-d: Make iommu_should_identity_map() take struct device
iommu/vt-d: Handle RMRRs for non-PCI devices
iommu/vt-d: Make get_domain_for_dev() take struct device
iommu/vt-d: Make domain_context_mapp{ed,ing}() take struct device
iommu/vt-d: Make device_to_iommu() cope with non-PCI devices
...
These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask
us to pick up the changes to avoid conflicts. A large chunk of this
are clock drivers (bcm281xx, exynos, versatile, shmobile), aside from
that, reset controllers for STi as well as a large rework of the
Marvell Orion/EBU watchdog driver are notable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=u/FI
-----END PGP SIGNATURE-----
Merge tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver changes from Arnd Bergmann:
"These changes are mostly for ARM specific device drivers that either
don't have an upstream maintainer, or that had the maintainer ask us
to pick up the changes to avoid conflicts.
A large chunk of this are clock drivers (bcm281xx, exynos, versatile,
shmobile), aside from that, reset controllers for STi as well as a
large rework of the Marvell Orion/EBU watchdog driver are notable"
* tag 'drivers-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (99 commits)
Revert "dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac."
Revert "net: stmmac: Add SOCFPGA glue driver"
ARM: shmobile: r8a7791: Fix SCIFA3-5 clocks
ARM: STi: Add reset controller support to mach-sti Kconfig
drivers: reset: stih416: add softreset controller
drivers: reset: stih415: add softreset controller
drivers: reset: Reset controller driver for STiH416
drivers: reset: Reset controller driver for STiH415
drivers: reset: STi SoC system configuration reset controller support
dts: socfpga: Add sysmgr node so the gmac can use to reference
dts: socfpga: Add support for SD/MMC on the SOCFPGA platform
reset: Add optional resets and stubs
ARM: shmobile: r7s72100: fix bus clock calculation
Power: Reset: Generalize qnap-poweroff to work on Synology devices.
dts: socfpga: Update clock entry to support multiple parents
ARM: socfpga: Update socfpga_defconfig
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
net: stmmac: Add SOCFPGA glue driver
watchdog: orion_wdt: Use %pa to print 'phys_addr_t'
drivers: cci: Export CCI PMU revision
...
A large part of the arm-soc patches are nowadays DT changes, adding support
for new SoCs, boards and devices without changing kernel source. The plan
is still to move the devicetree files out of the kernel tree and reduce
the amount of churn going on here, but we keep finding reasons to delay
doing that.
Changes are really all over the place, with little sticking out particularly.
We have contributions from a total of 116 people in this branch.
Unfortunately, the size of this branch also causes a significant number
of conflicts at the moment, typically when subsystem maintainers merge
patches that change the driver at the same time as the dts files. In
most cases this could be avoided because the dts changes are supposed
to be compatible in both ways, and we are asking everyone to send ARM
dts changes through our tree only.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=zl/N
-----END PGP SIGNATURE-----
Merge tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree changes from Arnd Bergmann:
"A large part of the arm-soc patches are nowadays DT changes, adding
support for new SoCs, boards and devices without changing kernel
source. The plan is still to move the devicetree files out of the
kernel tree and reduce the amount of churn going on here, but we keep
finding reasons to delay doing that.
Changes are really all over the place, with little sticking out
particularly. We have contributions from a total of 116 people in
this branch.
Unfortunately, the size of this branch also causes a significant
number of conflicts at the moment, typically when subsystem
maintainers merge patches that change the driver at the same time as
the dts files. In most cases this could be avoided because the dts
changes are supposed to be compatible in both ways, and we are asking
everyone to send ARM dts changes through our tree only"
* tag 'dt-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (541 commits)
dts: stmmac: Document the clocks property in the stmmac base document
dts: socfpga: Add DTS entry for adding the stmmac glue layer for stmmac.
ARM: STi: stih41x: Add support for the FSM Serial Flash Controller
ARM: STi: stih416: Add support for the FSM Serial Flash Controller
ARM: tegra: fix Dalmore pinctrl configuration
ARM: dts: keystone: use common "ti,keystone" compatible instead of -evm
ARM: dts: k2hk-evm: set ubifs partition size for 512M NAND
ARM: dts: Build all keystone dt blobs
ARM: dts: keystone: Fix control register range for clktsip
ARM: dts: keystone: Fix domain register range for clkfftc1
ARM: dts: bcm28155-ap: leave camldo1 on to fix reboot
ARM: dts: add bcm590xx pmu support and enable for bcm28155-ap
ARM: dts: bcm21664: Add device tree files.
ARM: DT: bcm21664: Device tree bindings
ARM: efm32: properly namespace i2c location property
ARM: efm32: fix unit address part in USART2 device nodes' names
ARM: mvebu: Enable NAND controller in Armada 385-DB
ARM: mvebu: Add support for NAND controller in Armada 38x SoC
ARM: mvebu: Add the Core Divider clock to Armada 38x SoCs
ARM: mvebu: Add a 2 GHz fixed-clock on Armada 38x SoCs
...
Lots of changes specific to one of the SoC families. Some that
stick out are:
* mach-qcom gains new features, most importantly SMP support for
the newer chips (Stephen Boyd, Rohit Vaswani)
* mvebu gains support for three new SoCs: Armada 375, 380 and 385
(Thomas Petazzoni and Free-electrons team)
* SMP support for Rockchips (Heiko Stübner)
* Lots of i.MX changes (Shawn Guo)
* Added support for BCM5301x SoC (Hauke Mehrtens)
* Multiplatform support for Marvell Kirkwood and Dove
(Andrew Lunn and Sebastian Hesselbarth doing the final part
of a long journey)
* Unify davinci platforms and remove obsolete ones (Sekhar Nori,
Arnd Bergmann)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=AGpV
-----END PGP SIGNATURE-----
Merge tag 'soc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC specific changes from Arnd Bergmann:
"Lots of changes specific to one of the SoC families. Some that stick
out are:
- mach-qcom gains new features, most importantly SMP support for the
newer chips (Stephen Boyd, Rohit Vaswani)
- mvebu gains support for three new SoCs: Armada 375, 380 and 385
(Thomas Petazzoni and Free-electrons team)
- SMP support for Rockchips (Heiko Stübner)
- Lots of i.MX changes (Shawn Guo)
- Added support for BCM5301x SoC (Hauke Mehrtens)
- Multiplatform support for Marvell Kirkwood and Dove (Andrew Lunn
and Sebastian Hesselbarth doing the final part of a long journey)
- Unify davinci platforms and remove obsolete ones (Sekhar Nori, Arnd
Bergmann)"
* tag 'soc-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (126 commits)
ARM: sunxi: Select HAVE_ARM_ARCH_TIMER
ARM: cache-tauros2: remove ARMv6 code
ARM: mvebu: don't select CONFIG_NEON
ARM: davinci: fix DT booting with default defconfig
ARM: configs: bcm_defconfig: enable bcm590xx regulator support
ARM: davinci: remove tnetv107x support
MAINTAINERS: Update ARM STi maintainers
ARM: restrict BCM_KONA_UART to ARCH_BCM_MOBILE
ARM: bcm21664: Add board support.
ARM: sunxi: Add the new watchog compatibles to the reboot code
ARM: enable ARM_HAS_SG_CHAIN for multiplatform
ARM: davinci: remove da8xx_omapl_defconfig
ARM: davinci: da8xx: fix multiple watchdog device registration
ARM: davinci: add da8xx specific configs to davinci_all_defconfig
ARM: davinci: enable da8xx build concurrently with older devices
ARM: BCM5301X: workaround suppress fault
ARM: BCM5301X: add early debugging support
ARM: BCM5301X: initial support for the BCM5301X/BCM470X SoCs with ARM CPU
ARM: mach-bcm: Remove GENERIC_TIME
ARM: shmobile: APMU: Fix warnings due to improper printk formats
...
These cleanup patches are mainly move stuff around and should all
be harmless. They are mainly split out so that other branches can
be based on top to avoid conflicts.
Notable changes are:
* We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used. (Uwe Kleine-König)
* The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions. (Kumar Gala)
* A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
* Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
* mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
* at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GcBb
-----END PGP SIGNATURE-----
Merge tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Arnd Bergmann:
"These cleanup patches are mainly move stuff around and should all be
harmless. They are mainly split out so that other branches can be
based on top to avoid conflicts.
Notable changes are:
- We finally remove all mach/timex.h, after CLOCK_TICK_RATE is no
longer used (Uwe Kleine-König)
- The Qualcomm MSM platform is split out into legacy mach-msm and
new-style mach-qcom, to allow easier maintainance of the new
hardware support without regressions (Kumar Gala)
- A rework of some of the Kconfig logic to simplify multiplatform
support (Rob Herring)
- Samsung Exynos gets closer to supporting multiplatform (Sachin
Kamat and others)
- mach-bcm3528 gets merged into mach-bcm (Stephen Warren)
- at91 gains some common clock framework support (Alexandre Belloni,
Jean-Jacques Hiblot and other French people)"
* tag 'cleanup-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (89 commits)
ARM: hisi: select HAVE_ARM_SCU only for SMP
ARM: efm32: allow uncompress debug output
ARM: prima2: build reset code standalone
ARM: at91: add PWM clock
ARM: at91: move sam9261 SoC to common clk
ARM: at91: prepare common clk transition for sam9261 SoC
ARM: at91: updated the at91_dt_defconfig with support for the ADS7846
ARM: at91: dt: sam9261: Device Tree support for the at91sam9261ek
ARM: at91: dt: defconfig: Added the sam9261 to the list of DT-enabled SOCs
ARM: at91: dt: Add at91sam9261 dt SoC support
ARM: at91: switch sam9rl to common clock framework
ARM: at91/dt: define main clk frequency of at91sam9rlek
ARM: at91/dt: define at91sam9rl clocks
ARM: at91: prepare common clk transition for sam9rl SoCs
ARM: at91: prepare sam9 dt boards transition to common clk
ARM: at91: dt: sam9rl: Device Tree for the at91sam9rlek
ARM: at91/defconfig: Add the sam9rl to the list of DT-enabled SOCs
ARM: at91: Add at91sam9rl DT SoC support
ARM: at91: prepare at91sam9rl DT transition
ARM: at91/defconfig: refresh at91sam9260_9g20_defconfig
...
Lots of isolated bug fixes that were not found to be important
enough to be submitted before the merge window or backported
into stable kernels.
The vast majority of these came out of Arnd's randconfig testing
and just prevents running into build-time bugs in configurations
that we do not care about in practice.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=KRJL
-----END PGP SIGNATURE-----
Merge tag 'fixes-non-critical-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical bug fixes from Arnd Bergmann:
"Lots of isolated bug fixes that were not found to be important enough
to be submitted before the merge window or backported into stable
kernels.
The vast majority of these came out of Arnd's randconfig testing and
just prevents running into build-time bugs in configurations that we
do not care about in practice"
* tag 'fixes-non-critical-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (75 commits)
ARM: at91: fix a typo
ARM: moxart: fix CPU selection
ARM: tegra: fix board DT pinmux setup
ARM: nspire: Fix compiler warning
IXP4xx: Fix DMA masks.
Revert "ARM: ixp4xx: Make dma_set_coherent_mask common, correct implementation"
IXP4xx: Fix Goramo Multilink GPIO conversion.
Revert "ARM: ixp4xx: fix gpio rework"
ARM: tegra: make debug_ll code build for ARMv6
ARM: sunxi: fix build for THUMB2_KERNEL
ARM: exynos: add missing include of linux/module.h
ARM: exynos: fix l2x0 saved regs handling
ARM: samsung: select CRC32 for SAMSUNG_PM_CHECK
ARM: samsung: select ATAGS where necessary
ARM: samsung: fix SAMSUNG_PM_DEBUG Kconfig logic
ARM: samsung: allow serial driver to be disabled
ARM: s5pv210: enable IDE support in MACH_TORBRECK
ARM: s5p64x0: fix building with only one soc type
ARM: s3c64xx: select power domains only when used
ARM: s3c64xx: MACH_SMDK6400 needs HSMMC1
...
Pull ARM changes from Russell King:
- Perf updates from Will Deacon:
- Support for Qualcomm Krait processors (run perf on your phone!)
- Support for Cortex-A12 (run perf stat on your FPGA!)
- Support for perf_sample_event_took, allowing us to automatically decrease
the sample rate if we can't handle the PMU interrupts quickly enough
(run perf record on your FPGA!).
- Basic uprobes support from David Long:
This patch series adds basic uprobes support to ARM. It is based on
patches developed earlier by Rabin Vincent. That approach of adding
hooks into the kprobes instruction parsing code was not well received.
This approach separates the ARM instruction parsing code in kprobes out
into a separate set of functions which can be used by both kprobes and
uprobes. Both kprobes and uprobes then provide their own semantic action
tables to process the results of the parsing.
- ARMv7M (microcontroller) updates from Uwe Kleine-König
- OMAP DMA updates (recently added Vinod's Ack even though they've been
sitting in linux-next for a few months) to reduce the reliance of
omap-dma on the code in arch/arm.
- SA11x0 changes from Dmitry Eremin-Solenikov and Alexander Shiyan
- Support for Cortex-A12 CPU
- Align support for ARMv6 with ARMv7 so they can cooperate better in a
single zImage.
- Addition of first AT_HWCAP2 feature bits for ARMv8 crypto support.
- Removal of IRQ_DISABLED from various ARM files
- Improved efficiency of virt_to_page() for single zImage
- Patch from Ulf Hansson to permit runtime PM callbacks to be available for
AMBA devices for suspend/resume as well.
- Finally kill asm/system.h on ARM.
* 'for-linus' of git://ftp.arm.linux.org.uk/~rmk/linux-arm: (89 commits)
dmaengine: omap-dma: more consolidation of CCR register setup
dmaengine: omap-dma: move IRQ handling to omap-dma
dmaengine: omap-dma: move register read/writes into omap-dma.c
ARM: omap: dma: get rid of 'p' allocation and clean up
ARM: omap: move dma channel allocation into plat-omap code
ARM: omap: dma: get rid of errata global
ARM: omap: clean up DMA register accesses
ARM: omap: remove almost-const variables
ARM: omap: remove references to disable_irq_lch
dmaengine: omap-dma: cleanup errata 3.3 handling
dmaengine: omap-dma: provide register read/write functions
dmaengine: omap-dma: use cached CCR value when enabling DMA
dmaengine: omap-dma: move barrier to omap_dma_start_desc()
dmaengine: omap-dma: move clnk_ctrl setting to preparation functions
dmaengine: omap-dma: improve efficiency loading C.SA/C.EI/C.FI registers
dmaengine: omap-dma: consolidate clearing channel status register
dmaengine: omap-dma: move CCR buffering disable errata out of the fast path
dmaengine: omap-dma: provide register definitions
dmaengine: omap-dma: consolidate setup of CCR
dmaengine: omap-dma: consolidate setup of CSDP
...
Various fbdev fixes and improvements, but nothing big.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=bavN
-----END PGP SIGNATURE-----
Merge tag 'fbdev-main-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux
Pull fbdev changes from Tomi Valkeinen:
"Various fbdev fixes and improvements, but nothing big"
* tag 'fbdev-main-3.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tomba/linux: (38 commits)
fbdev: Make the switch from generic to native driver less alarming
Video: atmel: avoid the id of fix screen info is overwritten
video: imxfb: Add DT default contrast control register property.
video: atmel_lcdfb: ensure the hardware is initialized with the correct mode
fbdev: vesafb: add dev->remove() callback
fbdev: efifb: add dev->remove() callback
video: pxa3xx-gcu: switch to devres functions
video: pxa3xx-gcu: provide an empty .open call
video: pxa3xx-gcu: pass around struct device *
video: pxa3xx-gcu: rename some symbols
sisfb: fix 1280x720 resolution support
video: fbdev: uvesafb: Remove impossible code path in uvesafb_init_info
video: fbdev: uvesafb: Remove redundant NULL check in uvesafb_remove
fbdev: FB_OPENCORES should depend on HAS_DMA
OMAPDSS: convert pixel clock to common videomode style
OMAPDSS: Remove unused get_context_loss_count support
OMAPDSS: use DISPC register to detect context loss
video: da8xx-fb: Use "SIMPLE_DEV_PM_OPS" macro
video: imxfb: Convert to SIMPLE_DEV_PM_OPS
video: imxfb: Resolve mismatch between backlight/contrast
...
Pull media updates from Mauro Carvalho Chehab:
"The main set of series of patches for media subsystem, including:
- document RC sysfs class
- added an API to setup scancode to allow waking up systems using the
Remote Controller
- add API for SDR devices. Drivers are still on staging
- some API improvements for getting EDID data from media
inputs/outputs
- new DVB frontend driver for drx-j (ATSC)
- one driver (it913x/it9137) got removed, in favor of an improvement
on another driver (af9035)
- added a skeleton V4L2 PCI driver at documentation
- added a dual flash driver (lm3646)
- added a new IR driver (img-ir)
- added an IR scancode decoder for the Sharp protocol
- some improvements at the usbtv driver, to allow its core to be
reused.
- added a new SDR driver (rtl2832u_sdr)
- added a new tuner driver (msi001)
- several improvements at em28xx driver to fix PM support, device
removal and to split the V4L2 specific bits into a separate
sub-driver
- one driver got converted to videobuf2 (s2255drv)
- the e4000 tuner driver now follows an improved binding model
- some fixes at V4L2 compat32 code
- several fixes and enhancements at videobuf2 code
- some cleanups at V4L2 API documentation
- usual driver enhancements, new board additions and misc fixups"
[ NOTE! This merge effective drops commit 4329b93b28 ("of: Reduce
indentation in of_graph_get_next_endpoint").
The of_graph_get_next_endpoint() function was moved and renamed by
commit fd9fdb78a9 ("[media] of: move graph helpers from
drivers/media/v4l2-core to drivers/of"). It was originally called
v4l2_of_get_next_endpoint() and lived in the file
drivers/media/v4l2-core/v4l2-of.c.
In that original location, it was then fixed to support empty port
nodes by commit b9db140c1e ("[media] v4l: of: Support empty port
nodes"), and that commit clashes badly with the dropped "Reduce
intendation" commit. I had to choose one or the other, and decided
that the "Support empty port nodes" commit was more important ]
* 'v4l_for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (426 commits)
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
Revert "[media] em28xx-dvb: fix PCTV 461e tuner I2C binding"
[media] em28xx: fix PCTV 290e LNA oops
[media] em28xx-dvb: fix PCTV 461e tuner I2C binding
[media] m88ds3103: fix bug on .set_tone()
[media] saa7134: fix WARN_ON during resume
[media] v4l2-dv-timings: add module name, description, license
[media] videodev2.h: add parenthesis around macro arguments
[media] saa6752hs: depends on CRC32
[media] si4713: fix Kconfig dependencies
[media] Sensoray 2255 uses videobuf2
[media] adv7180: free an interrupt on failure paths in init_device()
[media] e4000: make VIDEO_V4L2 dependency optional
[media] af9033: Don't export functions for the hardware filter
[media] af9035: use af9033 PID filters
[media] af9033: implement PID filter
[media] rtl2832_sdr: do not use dynamic stack allocation
[media] e4000: fix 32-bit build error
[media] em28xx-audio: make sure audio is unmuted on open()
[media] DocBook media: v4l2_format_sdr was renamed to v4l2_sdr_format
...
Remove pdata quirks for the displays on boards that are now supported
properly with DT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Export the DMA register information from the SoC specific data, such
that we can access the registers directly in omap-dma.c, mapping the
register region ourselves as well.
Rather than calculating the DMA channel register in its entirety for
each access, we pre-calculate an offset base address for the allocated
DMA channel and then just use the appropriate register offset.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The omap_system_dma_plat_info structure is only seven words, it's not
worth the expense of kmalloc()'ing backing store for this only to
release it later. Note that platform_device_add_data() copies the
data anyway. Clean up the initialisation of this structure - we don't
even need code to initialise most of this structure.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This really needs to be there, because otherwise the plat-omap code can
kfree() this data structure, and then re-use the pointer later.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There's no need for this to be a global variable; move it into the
errata configuration function instead.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We can do much better with this by using a structure to describe each
register, rather than code.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
dma_stride and dma_common_ch_start are only ever initialised to one
known value at initialisation, and are private to each of these files.
There's no point these being variables at all.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The disable_irq_lch method is never actually used, so there's not much
point it existing; remove it.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Pull networking updates from David Miller:
"Here is my initial pull request for the networking subsystem during
this merge window:
1) Support for ESN in AH (RFC 4302) from Fan Du.
2) Add full kernel doc for ethtool command structures, from Ben
Hutchings.
3) Add BCM7xxx PHY driver, from Florian Fainelli.
4) Export computed TCP rate information in netlink socket dumps, from
Eric Dumazet.
5) Allow IPSEC SA to be dumped partially using a filter, from Nicolas
Dichtel.
6) Convert many drivers to pci_enable_msix_range(), from Alexander
Gordeev.
7) Record SKB timestamps more efficiently, from Eric Dumazet.
8) Switch to microsecond resolution for TCP round trip times, also
from Eric Dumazet.
9) Clean up and fix 6lowpan fragmentation handling by making use of
the existing inet_frag api for it's implementation.
10) Add TX grant mapping to xen-netback driver, from Zoltan Kiss.
11) Auto size SKB lengths when composing netlink messages based upon
past message sizes used, from Eric Dumazet.
12) qdisc dumps can take a long time, add a cond_resched(), From Eric
Dumazet.
13) Sanitize netpoll core and drivers wrt. SKB handling semantics.
Get rid of never-used-in-tree netpoll RX handling. From Eric W
Biederman.
14) Support inter-address-family and namespace changing in VTI tunnel
driver(s). From Steffen Klassert.
15) Add Altera TSE driver, from Vince Bridgers.
16) Optimizing csum_replace2() so that it doesn't adjust the checksum
by checksumming the entire header, from Eric Dumazet.
17) Expand BPF internal implementation for faster interpreting, more
direct translations into JIT'd code, and much cleaner uses of BPF
filtering in non-socket ocntexts. From Daniel Borkmann and Alexei
Starovoitov"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1976 commits)
netpoll: Use skb_irq_freeable to make zap_completion_queue safe.
net: Add a test to see if a skb is freeable in irq context
qlcnic: Fix build failure due to undefined reference to `vxlan_get_rx_port'
net: ptp: move PTP classifier in its own file
net: sxgbe: make "core_ops" static
net: sxgbe: fix logical vs bitwise operation
net: sxgbe: sxgbe_mdio_register() frees the bus
Call efx_set_channels() before efx->type->dimension_resources()
xen-netback: disable rogue vif in kthread context
net/mlx4: Set proper build dependancy with vxlan
be2net: fix build dependency on VxLAN
mac802154: make csma/cca parameters per-wpan
mac802154: allow only one WPAN to be up at any given time
net: filter: minor: fix kdoc in __sk_run_filter
netlink: don't compare the nul-termination in nla_strcmp
can: c_can: Avoid led toggling for every packet.
can: c_can: Simplify TX interrupt cleanup
can: c_can: Store dlc private
can: c_can: Reduce register access
can: c_can: Make the code readable
...
Updates to devicetree core code. This branch contains the following notable changes:
* Add reserved memory binding
* Make struct device_node a kobject and remove legacy /proc/device-tree
* ePAPR conformance fixes
* Update in-kernel DTC copy to version v1.4.0
* Preparation changes for dynamic device tree overlays
* minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of the
old /proc/device-tree code. This simplifies the device tree handling
code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=lyA5
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus' of git://git.secretlab.ca/git/linux
Pull devicetree changes from Grant Likely:
"Updates to devicetree core code. This branch contains the following
notable changes:
- add reserved memory binding
- make struct device_node a kobject and remove legacy
/proc/device-tree
- ePAPR conformance fixes
- update in-kernel DTC copy to version v1.4.0
- preparatory changes for dynamic device tree overlays
- minor bug fixes and documentation changes
The most significant change in this branch is the conversion of struct
device_node to be a kobject that is exposed via sysfs and removal of
the old /proc/device-tree code. This simplifies the device tree
handling code and tightens up the lifecycle on device tree nodes.
[updated: added fix for dangling select PROC_DEVICETREE]"
* tag 'dt-for-linus' of git://git.secretlab.ca/git/linux: (29 commits)
dt: Remove dangling "select PROC_DEVICETREE"
of: Add support for ePAPR "stdout-path" property
of: device_node kobject lifecycle fixes
of: only scan for reserved mem when fdt present
powerpc: add support for reserved memory defined by device tree
arm64: add support for reserved memory defined by device tree
of: add missing major vendors
of: add vendor prefix for SMSC
of: remove /proc/device-tree
of/selftest: Add self tests for manipulation of properties
of: Make device nodes kobjects so they show up in sysfs
arm: add support for reserved memory defined by device tree
drivers: of: add support for custom reserved memory drivers
drivers: of: add initialization code for dynamic reserved memory
drivers: of: add initialization code for static reserved memory
of: document bindings for reserved-memory nodes
Revert "of: fix of_update_property()"
kbuild: dtbs_install: new make target
ARM: mvebu: Allows to get the SoC ID even without PCI enabled
of: Allows to use the PCI translator without the PCI core
...
CONFIG_PROC_DEVICETREE has been removed from the tree. This commit
removes a dangling select of the config symbol.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: Rob Herring <rob.herring@linaro.org>
As there is no common panel framework in the kernel, we have OMAP
specific panel drivers. However, the DT data should be generic. This
brings the issue that some other platform could use the same panels, and
would need to create a driver with the same 'compatible' string as the
OMAP driver.
In the long run, we have to get a common panel framework. For the time
being, this patch solves the issue:
At early boot time, we go through the DT nodes looking for the panels
the kernel supports for OMAP. For each found node, the 'compatible'
string is prepended with "omapdss,", i.e. "sony,acx565akm" becomes
"omapdss,sony,acx565akm". The OMAP display drivers all have "omapdss,"
at the beginning of their compatible field.
This allows us to have generic DT data, but OMAP specific display
drivers.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
The OMAP display architecture requires a bunch of platform devices which
are not created via .dts (for now). We also need to pass a few function
pointers and the DSS hardware version from the arch code to omapdss
driver.
This patch adds omapdss_init_of() function, called from board-generic at
init time, which handles those tasks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: Archit Taneja <archit@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
These are sent separately from the rest of the .dts changes
as these depend on the fixes merged into v3.14-rc4, and
needed a bit more time to get updated on the fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJTIMPtAAoJEBvUPslcq6VzYzUP/R/CjdMRley2yjwnxkZ/pk6w
cUitKvWpVcu4M7VMaEsGj7x33PuvYF3Ukn2RLX5/XrWEI+4ec6Ny3cWOAiRr8pmv
7ojBfNTtM3l8wRlJE/cZ5tfX+24nc6Ofufwi0ax+LoFZEh/JNdWXzFwd68mlxlCM
NlQakcwN3ReZ4y30C8vZJmQwLqiIw0LDFOoBPB9C7Zgc735brQBm5fnzVFJWrnq0
RIIB5hWJ+fmyP3jHRN5XmNLPEMKULK7GUgX1UMF99imQf548agYvstbazZVRVr6D
i1Tkq/9W8UTT1wrUYfagr94Oj61vyqSUZJm5pHjehi+hfUkvHX4sxLup+WXIIA9L
LObz368BaHGQ7FrryEe/FYZdnmjaluK1nw4Huobnv5GXvp6XPG36yEo9L6LbiNvK
+uRnV2k+OdJ9cHIYwxNQC7dNcr+qHvTWGOrU3Q++OAVi+dClUO7G0/+xh5NQbsBA
jApGa8FQrk4S5jgNEFzFnpj4XPTE/88pbrQfZq5RsGQ+P1Jx5r9dbzndVft+b1C2
uC0tLsJDX3RJCbk4N0JZACygaIvVfH4sybf34FTDP19r9eKWKSpHjHZAtnJ7AIss
Iz0AxxKnUFwy3Kx01DN8vZeLt0wRF2THn+nOkqM0ZO5r1ptNa1dBHXkrWVP5gybn
WnN9onC6O4Wa2wEvCxVd
=rAdr
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/dt-overo-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Updates to the .dts files to support more Gumstix boards.
These are sent separately from the rest of the .dts changes
as these depend on the fixes merged into v3.14-rc4, and
needed a bit more time to get updated on the fixes.
* tag 'omap-for-v3.15/dt-overo-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add support for the Overo Summit
ARM: dts: Add support for the Overo Chestnut43
ARM: dts: Add support for the Overo Alto35
ARM: dts: Add support for the Overo Gallop43
ARM: dts: Add support for the Overo Palo43
ARM: dts: overo: Add LIS33DE accelerometer
ARM: dts: overo: Create a file for common Gumstix peripherals
ARM: dts: overo: Push uart3 pinmux down to expansion board
ARM: dts: omap3-tobi: Add AT24C01 EEPROM
ARM: dts: omap3-tobi: Use include file omap-gpmc-smsc9221
ARM: dts: omap: Add common file for SMSC9221
ARM: dts: omap3-overo: Add HSUSB PHY
ARM: dts: omap3-overo: Enable WiFi/BT combo
ARM: dts: omap3-overo: Add missing pinctrl
ARM: dts: omap3-tobi: Add missing pinctrl
ARM: dts: overo: reorganize include files
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/boot/dts/omap3-overo.dtsi
is finally getting updated. Also few trivial board related
.dts updates to add more devices.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.15 (GNU/Linux)
iQIcBAABAgAGBQJTIMSBAAoJEBvUPslcq6VzimEP/2cJDRk76e+/kTvAmtl5L9JS
Z1QaM/YZ6dObHjZmrkeh0HbiFV61aJvESXyEtET70FBDZmWJJICGlR+weQH9dGOk
ejjsB14AdYiHDMRpp37V8M0xiZaUy0bUqEwwBCSE8HiTAM7lMluokXGZvKCRzxUQ
aTUhekdIPVBLtdgIU9/2o194chpM7CEUlIlveam8IL5xpjLJguywgsjniM/xl0ni
JcGaJM736HifgtOLCdIaWJ9SUk+UzmZ2cpP5auxt5+RAT1Omv3I2ztW8HTHMFNsK
iRcmEiXlJus6itpJ0jroLksL1apoFpm3XKKIOTkIL2pD+UM10M/iYdf/r46EUY/Y
pXABRkPIrYldgOMHrsFMCSxHfQJ7bqCs/Bs/mlJL90FwbB+akHFyuCuOTfLyaROQ
RqmtGJQt+Y62QBtXdhoQ3OpOwNSxNlWgXyv0UoyE4ZHaaeoSwMjuLbqE/W0d4L+z
CQdJLYWjKanWJkBZ/q6pYt5GKmW/oakDkHt28yI5rqwlWS3BUSgZQ5ghi12RPArG
E2hBzoaVRl030nHNtjcz7sO5xBFnEvqzy3/XcWzeByjl1XlWtfxokVPxBB46aXcm
sySlPnZGSJBY8S6Fnqs8/0hqQK+QLUfsZlXyvCYAWBVZGZ1OdzCdfR46dCx5xubD
t7bGfgTMGSIiskjCxdU7
=5f7K
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.15/dt-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/dt
Pull "omap device tree changes for v3.15, part 3" from Tony Lindgren:
Device tree related changes to the omap iommu driver as that
is finally getting updated. Also few trivial board related
.dts updates to add more devices.
* tag 'omap-for-v3.15/dt-part3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Add MMC2/SDIO/WLAN support for cm-t3530
ARM: dts: am335x-evmsk: enable DMA controller for USB
ARM: dts: OMAP5: Add IOMMU nodes
ARM: dts: OMAP4: Add IOMMU nodes
ARM: dts: OMAP3: Add IVA IOMMU node
ARM: dts: OMAP3: Update ISP IOMMU node
ARM: OMAP2+: extend iommu pdata-quirks to OMAP5
ARM: OMAP5: hwmod data: add mmu data for ipu & dsp
ARM: OMAP2+: use pdata quirks for iommu reset lines
ARM: OMAP2+: change the ISP device archdata MMU name for DT
ARM: OMAP3: fix iva mmu programming issues
ARM: OMAP3: remove deprecated CONFIG_OMAP_IOMMU_IVA2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
drivers/net/usb/r8152.c
drivers/net/xen-netback/netback.c
Both the r8152 and netback conflicts were simple overlapping
changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the proper clock name 'usbhost_120m_fck' instead of the
alias 'ehci_logic_fck'
Get rid of the 'ehci_logic_fck' alias from the OMAP3 hwmod data
as well.
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Not all revisions have all the clocks so get the necessary clocks
based on hardware revision.
This should avoid un-necessary clk_get failure messages that were
observed earlier.
Also remove the dummy USB host clocks from the OMAP3 clock data.
These are no longer expected by the driver.
Acked-by: Mike Turquette <mturquette@linaro.org> [OMAP3 CLK data]
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
