This patch add 400MHz and 500MHz to clock rate table for rk3288.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
We'd like to be able to call clk_set_rate() on aclk_cpu (a gate) at
bootup. In order for this to have any effect we need its parent
(aclk_cpu_pre) to percolate the rate change to _its_ parent
(aclk_cpu_src). Add CLK_SET_RATE_PARENT to make this happen.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The parent should be spdif_8ch_pre not spdif_8ch_src, which doesn't
exist and looks to be a typo. The TRM also confirms this.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Add infrastructure to write the correct value to the restart register and
register the restart notifier for both rk3188 (including rk3066) and rk3288.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The relation of i2s nodes as follows:
i2s_src 0 0 594000000 0
i2s_frac 0 0 11289600 0
i2s_pre 0 0 11289600 0
sclk_i2s0 0 0 11289600 0
i2s0_clkout 0 0 11289600 0
hclk_i2s0 1 1 99000000 0
sclk_i2s0 is the master clock, when to set rate of sclk_i2s0, should
allow to set its parent's rate, by add flag CLK_SET_RATE_PARENT for
"i2s_frac", "i2s_pre", "i2s0_clkout" and "sclk_i2s0".
Tested on rk3288 board using max98090, with command "aplay <music.wav>"
Change-Id: I12faad082566532b65a7de8c0a6845e1c17870e6
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This adds the necessary soc-specific divider values and switches the armclk
to use the newly introduced cpuclk type.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
When changing the armclk on Rockchip SoCs it is supposed to be reparented
to an alternate parent before changing the underlying pll and back after
the change. Additionally there exist clocks that are very tightly bound to
the armclk whose divider values are set according to the armclk rate.
Add a special clock-type to handle all that. The rate table and divider
values will be supplied from the soc-specific clock controllers.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
On a rk3288-board:
Tested-by: Doug Anderson <dianders@chromium.org>
Rockchip SoCs contain clocks tightly bound to the armclk, where the best
rate / divider is supplied by the vendor after careful measuring.
Often this ideal rate may be greater than the current rate.
Therefore prevent the ccf from trying to set these dividers itself by
setting them to read-only.
In the case of the rk3066, this also includes the aclk_cpu, which makes it
necessary to also split its direct child-clocks (pclk_cpu, hclk_cpu, ...)
into individual definitions for rk3066 and rk3188.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
aclk_cpu_pre on the rk3188 can either be sourced from the armclk or the gpll.
To reduce complexity on apll changes caused by cpufreq, reparent it always
to the gpll source.
If really necessary it could be reparented back on a per board level using
the assigned-clocks mechanism.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
In RK3288, APLL lock status bit is in GRF_SOC_STATUS1,
but in RK3188, is GRFSOC_STATUS0.
Signed-off-by: Jianqun <jay.xu@rock-chips.com>
Also name the constant accordingly as GRF_SOC_STATUS1
to prevent confusion.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
The register providing the pll lock status is at a different address on the
rk3066. The error became apparent while working on cpufreq support for
the rockchip SoCs.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
The Rockchip PLL code switches into slow mode (AKA bypass more AKA
24MHz mode) before actually changing the PLL. This keeps anyone from
using the PLL while it's changing. However, in all known Rockchip
SoCs nobody should ever see the 24MHz when changing the PLL supplying
the armclk because we should reparent children to an alternate
(faster than 24MHz) PLL.
One problem is that the code to switch to an alternate parent was
running in PRE_RATE_CHANGE. ...and the code to switch to slow mode
was _also_ running in PRE_RATE_CHANGE. That meant there was no real
guarantee that we would switch to an alternate parent before switching
to 24MHz mode.
Let's move the switch to "slow mode" straight into
rockchip_rk3066_pll_set_rate(). That means we're guaranteed that the
24MHz is really a last-resort.
Note that without this change on real systems we were the code to
switch to an alternate parent at 24MHz. In some older versions of
that code we'd appy a (temporary) / 5 to the 24MHz causing us to run
at 4.8MHz. That wasn't enough to service USB interrupts in some cases
and could lead to a system hang.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
This patch add the clock node in PD_VIDEO
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This patch use the new defined clock ID to initial the clock nodes.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The npll on rk3288 is exactly the same pll type as the other 4. Yet it
was missing the link to the rate table, making rate changes impossible.
Change that by setting the table.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The rk3288 actually has 12 softresets, so fix the register count.
Signed-off-by: Mark yao <mark.yao@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The dwc2 usb controller also uses agressive clock gating, which in this
case leads to hclk_peri getting disabled and hanging the system.
Therefore move it to the critical clocks until we also control that
part of the system.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clocks for i2c1 and i2c2 are flipped. The clock tree matched the
Technical Reference Manual (TRM) but the TRM was wrong. Swap them in
the clock tree. This was determined experimentally (by Addy) and
confirmed by the Rockchip IC team.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reported-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
The clock-tree contains clocks that should never get disabled automatically.
One example are the base ACLKs, the base supplies for all peripherals.
Therefore add a structure similar to the sunxi clock-tree to protect these
special clocks from being disabled.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
It is only used locally in clk/rockchip/clk.c and thus can be static.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Rockchip SoCs may provide fraction dividers for some clocks, mostly for
i2s and uarts. In contrast to the other registers, these do not use
the hiword-mask paradigm, but instead split the register into the upper
16 bit for the nominator and the lower 16 bit for the denominator.
The common clock framework got a generic fractional divider clock type
recently that can accomodate this setting easily. All currently known
fraction dividers have a separate gate too, therefore implement the
divider as composite using the ops-struct from fractional_divider clock
and add the gate if necessary.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Add the clock tree definition for the new rk3288 SoC.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This adds a clock driver that handles the specific muxes, dividers and gates
of rk3188 and rk3066 SoCs.
The structure of the clock list resembles the arrangement of their
counterparts in the clock architecture diagrams found in the SoC
documentation.
Clocks exported to the clock provider are currently limited to well known
or measured ones. So additional clock exports may be necessary in the future.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
All Rockchip SoCs at least down to the ARM9-based RK28xx include the reset-
controller for SoC peripherals in their clock controller.
While the older SoCs (ARM9 and Cortex-A8) use a regular scheme to change
register values, the Cortex-A9 SoCs use a hiword-mask making locking unecessary.
To be compatible with both schemes the reset controller takes a flag to
decide which scheme to use, similar to the other HIWORD_MASK flags used in the
clock framework.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
All known Rockchip SoCs down to the RK28xx (ARM9) use a similar pattern to
handle their plls:
|--\
xin32k ----------------|mux\
xin24m -----| pll |----|pll|--- pll output
\---------------|src/
|--/
The pll output is sourced from 1 of 3 sources, the actual pll being one of
them. To change the pll frequency it is imperative to remux it to another
source beforehand. This is done by adding a clock-listener to the pll that
handles the remuxing before and after the rate change.
The output mux is implemented as a separate clock to make use of already
existing common-clock features for disabling the pll if one of the other
two sources is used.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
This adds infrastructure for registering clock branches. On Rockchip SoCs
most clock branches are a combination of mux,divider and gate components,
thus a composite clock is used when appropriate.
Clock branches are supposed to be declared in an array using the COMPOSITE*
or MUX, etc makros defined in the header and then registered using
rockchip_clk_register_branches.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-By: Max Schwarz <max.schwarz@online.de>
Tested-By: Max Schwarz <max.schwarz@online.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Adding function type checking to CLK_OF_DECLARE found a type mismatch with
rk2928_gate_clk_init. The function only takes a single struct device_node
parameter.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
This adds basic support for gate-clocks on Rockchip SoCs.
There are 16 gates in each register and use the HIWORD_MASK
mechanism for changing gate settings.
The gate registers form a continuos block which makes the dt node
structure a matter of taste, as either all 160 gates can be put into
one gate clock spanning all registers or they can be divided into
the 10 individual gates containing 16 clocks each.
The code supports both approaches.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
