When userspace passes a large priority value
the assignment of the unsigned value hopt->prio
to signed int cl->prio causes cl->prio to become negative and the
comparison is with TC_HTB_NUMPRIO is always false.
The result is that HTB crashes by referencing outside
the array when processing packets. With this patch the large value
wraps around like other values outside the normal range.
See: https://bugzilla.kernel.org/show_bug.cgi?id=60669
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eliezer renames several *ll_poll to *busy_poll, but forgets
CONFIG_NET_LL_RX_POLL, so in case of confusion, rename it too.
Cc: Eliezer Tamir <eliezer.tamir@linux.intel.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a race in IPv6 automatic addess assignment. The address is created
with zero lifetime when it's added to various address lists. Before it gets
assigned the correct lifetime, there's a window where a new address may be
configured. This causes the semi-initiated address to be deleted in
addrconf_verify.
This was discovered as a reference leak caused by concurrent run of
__ipv6_ifa_notify for both RTM_NEWADDR and RTM_DELADDR with the same
address.
Fix this by setting the lifetime before the address is added to
inet6_addr_lst.
A few notes:
1. In addrconf_prefix_rcv, by setting update_lft to zero, the
if (update_lft) { ... } condition is no longer executed for newly
created addresses. This is okay, as the ifp fields are set in
ipv6_add_addr now and ipv6_ifa_notify is called (and has been called)
through addrconf_dad_start.
2. The removal of the whole block under ifp->lock in inet6_addr_add is okay,
too, as tstamp is initialized to jiffies in ipv6_add_addr.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
As pointed out by Eric Dumazet, net->ipv6.ip6_rt_last_gc should
hold the last time garbage collector was run so that we should
update it whenever fib6_run_gc() calls fib6_clean_all(), not only
if we got there from ip6_dst_gc().
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
On a high-traffic router with many processors and many IPv6 dst
entries, soft lockup in fib6_run_gc() can occur when number of
entries reaches gc_thresh.
This happens because fib6_run_gc() uses fib6_gc_lock to allow
only one thread to run the garbage collector but ip6_dst_gc()
doesn't update net->ipv6.ip6_rt_last_gc until fib6_run_gc()
returns. On a system with many entries, this can take some time
so that in the meantime, other threads pass the tests in
ip6_dst_gc() (ip6_rt_last_gc is still not updated) and wait for
the lock. They then have to run the garbage collector one after
another which blocks them for quite long.
Resolve this by replacing special value ~0UL of expire parameter
to fib6_run_gc() by explicit "force" parameter to choose between
spin_lock_bh() and spin_trylock_bh() and call fib6_run_gc() with
force=false if gc_thresh is reached but not max_size.
Signed-off-by: Michal Kubecek <mkubecek@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
If there is no querier on a link then we won't get periodic reports and
therefore won't be able to learn about multicast listeners behind ports,
potentially leading to lost multicast packets, especially for multicast
listeners that joined before the creation of the bridge.
These lost multicast packets can appear since c5c2326059
("bridge: Add multicast_querier toggle and disable queries by default")
in particular.
With this patch we are flooding multicast packets if our querier is
disabled and if we didn't detect any other querier.
A grace period of the Maximum Response Delay of the querier is added to
give multicast responses enough time to arrive and to be learned from
before disabling the flooding behaviour again.
Signed-off-by: Linus Lüssing <linus.luessing@web.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "pvc" struct has a hole after pvc.sap_family which is not cleared.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking fixes from David Miller:
1) Fix association failures not triggering a connect-failure event in
cfg80211, from Johannes Berg.
2) Eliminate a potential NULL deref with older iptables tools when
configuring xt_socket rules, from Eric Dumazet.
3) Missing RTNL locking in wireless regulatory code, from Johannes
Berg.
4) Fix OOPS caused by firmware loading races in ath9k_htc, from Alexey
Khoroshilov.
5) Fix usb URB leak in usb_8dev CAN driver, also from Alexey
Khoroshilov.
6) VXLAN namespace teardown fails to unregister devices, from Stephen
Hemminger.
7) Fix multicast settings getting dropped by firmware in qlcnic driver,
from Sucheta Chakraborty.
8) Add sysctl range enforcement for tcp_syn_retries, from Michal Tesar.
9) Fix a nasty bug in bridging where an active timer would get
reinitialized with a setup_timer() call. From Eric Dumazet.
10) Fix use after free in new mlx5 driver, from Dan Carpenter.
11) Fix freed pointer reference in ipv6 multicast routing on namespace
cleanup, from Hannes Frederic Sowa.
12) Some usbnet drivers report TSO and SG in their feature set, but the
usbnet layer doesn't really support them. From Eric Dumazet.
13) Fix crash on EEH errors in tg3 driver, from Gavin Shan.
14) Drop cb_lock when requesting modules in genetlink, from Stanislaw
Gruszka.
15) Kernel stack leaks in cbq scheduler and af_key pfkey messages, from
Dan Carpenter.
16) FEC driver erroneously signals NETDEV_TX_BUSY on transmit leading to
endless loops, from Uwe Kleine-König.
17) Fix hangs from loading mvneta driver, from Arnaud Patard.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (84 commits)
mlx5: fix error return code in mlx5_alloc_uuars()
mvneta: Try to fix mvneta when compiled as module
mvneta: Fix hang when loading the mvneta driver
atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
genetlink: fix usage of NLM_F_EXCL or NLM_F_REPLACE
af_key: more info leaks in pfkey messages
net/fec: Don't let ndo_start_xmit return NETDEV_TX_BUSY without link
net_sched: Fix stack info leak in cbq_dump_wrr().
igb: fix vlan filtering in promisc mode when not in VT mode
ixgbe: Fix Tx Hang issue with lldpad on 82598EB
genetlink: release cb_lock before requesting additional module
net: fec: workaround stop tx during errata ERR006358
qlcnic: Fix diagnostic interrupt test for 83xx adapters.
qlcnic: Fix setting Guest VLAN
qlcnic: Fix operation type and command type.
qlcnic: Fix initialization of work function.
Revert "atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring"
atl1c: Fix misuse of netdev_alloc_skb in refilling rx ring
net/tg3: Fix warning from pci_disable_device()
net/tg3: Fix kernel crash
...
We have:
- A build failure fix for the NCI SPI transport layer due to a
missing CRC_CCITT Kconfig dependency.
- A netlink command rename: CMD_FW_UPLOAD was merged during the 3.11
merge window but the typical terminology for loading a firmware to a
target is firmware download rather than upload. In order to avoid any
confusion in a file exported to userspace, we rename this command into
CMD_FW_DOWNLOAD.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=p4r5
-----END PGP SIGNATURE-----
Merge tag 'nfc-fixes-3.11-2' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/nfc-fixes
Samuel Ortiz <sameo@linux.intel.com> says:
'This is the second NFC fixes pull request for 3.11.
We have:
- A build failure fix for the NCI SPI transport layer due to a
missing CRC_CCITT Kconfig dependency.
- A netlink command rename: CMD_FW_UPLOAD was merged during the 3.11
merge window but the typical terminology for loading a firmware to a
target is firmware download rather than upload. In order to avoid any
confusion in a file exported to userspace, we rename this command into
CMD_FW_DOWNLOAD."
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, it is not possible to use neither NLM_F_EXCL nor
NLM_F_REPLACE from genetlink. This is due to this checking in
genl_family_rcv_msg:
if (nlh->nlmsg_flags & NLM_F_DUMP)
NLM_F_DUMP is NLM_F_MATCH|NLM_F_ROOT. Thus, if NLM_F_EXCL or
NLM_F_REPLACE flag is set, genetlink believes that you're
requesting a dump and it calls the .dumpit callback.
The solution that I propose is to refine this checking to
make it stricter:
if ((nlh->nlmsg_flags & NLM_F_DUMP) == NLM_F_DUMP)
And given the combination NLM_F_REPLACE and NLM_F_EXCL does
not make sense to me, it removes the ambiguity.
There was a patch that tried to fix this some time ago (0ab03c2
netlink: test for all flags of the NLM_F_DUMP composite) but it
tried to resolve this ambiguity in *all* existing netlink subsystems,
not only genetlink. That patch was reverted since it broke iproute2,
which is using NLM_F_ROOT to request the dump of the routing cache.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is inspired by a5cc68f3d6 "af_key: fix info leaks in notify
messages". There are some struct members which don't get initialized
and could disclose small amounts of private information.
Acked-by: Mathias Krause <minipli@googlemail.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loading a firmware into a target is typically called firmware
download, not firmware upload. So we rename the netlink API to
NFC_CMD_FW_DOWNLOAD in order to avoid any terminology confusion from
userspace.
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make sure the reserved fields, and padding (if any), are
fully initialized.
Based upon a patch by Dan Carpenter and feedback from
Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>
In certain circumstances, such as an HCI driver using __hci_cmd_sync_ev
with HCI_EV_CMD_COMPLETE as the expected completion event there is the
chance that hci_event_packet will call hci_req_cmd_complete twice (once
for the explicitly looked after event and another time in the actual
handler of cmd_complete).
In the case of __hci_cmd_sync_ev this introduces a race where the first
call wakes up the blocking __hci_cmd_sync_ev and lets it complete.
However, by the time that a second __hci_cmd_sync_ev call is already in
progress the second hci_req_cmd_complete call (from the previous
operation) will wake up the blocking function prematurely and cause it
to fail, as witnessed by the following log:
[ 639.232195] hci_rx_work: hci0 Event packet
[ 639.232201] hci_req_cmd_complete: opcode 0xfc8e status 0x00
[ 639.232205] hci_sent_cmd_data: hci0 opcode 0xfc8e
[ 639.232210] hci_req_sync_complete: hci0 result 0x00
[ 639.232220] hci_cmd_complete_evt: hci0 opcode 0xfc8e
[ 639.232225] hci_req_cmd_complete: opcode 0xfc8e status 0x00
[ 639.232228] __hci_cmd_sync_ev: hci0 end: err 0
[ 639.232234] __hci_cmd_sync_ev: hci0
[ 639.232238] hci_req_add_ev: hci0 opcode 0xfc8e plen 250
[ 639.232242] hci_prepare_cmd: skb len 253
[ 639.232246] hci_req_run: length 1
[ 639.232250] hci_sent_cmd_data: hci0 opcode 0xfc8e
[ 639.232255] hci_req_sync_complete: hci0 result 0x00
[ 639.232266] hci_cmd_work: hci0 cmd_cnt 1 cmd queued 1
[ 639.232271] __hci_cmd_sync_ev: hci0 end: err 0
[ 639.232276] Bluetooth: hci0 sending Intel patch command (0xfc8e) failed (-61)
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
None of the BlueFRITZ! devices with manufacurer ID 31 (AVM Berlin)
support HCI_Read_Local_Supported_Commands. It is safe to use the
manufacturer ID (instead of e.g. a USB ID specific quirk) because the
company never created any newer controllers.
< HCI Command: Read Local Supported Comm.. (0x04|0x0002) plen 0 [hci0] 0.210014
> HCI Event: Command Status (0x0f) plen 4 [hci0] 0.217361
Read Local Supported Commands (0x04|0x0002) ncmd 1
Status: Unknown HCI Command (0x01)
Reported-by: Jörg Esser <jackfritt@boh.de>
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
Tested-by: Jörg Esser <jackfritt@boh.de>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Without this patch, the fields app_solicit, gc_thresh1, gc_thresh2,
gc_thresh3, proxy_qlen, ucast_solicit, mcast_solicit could have
assumed negative values when setting large numbers.
Signed-off-by: Francesco Fusco <ffusco@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If hci_dev_open() is called after hci_register_dev() added the device to
the hci_dev_list but before the workqueue are created we could run into a
NULL pointer dereference (see below).
This bug is very unlikely to happen, systems using bluetoothd to
manage their bluetooth devices will never see this happen.
BUG: unable to handle kernel NULL pointer dereference
0100
IP: [<ffffffff81077502>] __queue_work+0x32/0x3d0
(...)
Call Trace:
[<ffffffff81077be5>] queue_work_on+0x45/0x50
[<ffffffffa016e8ff>] hci_req_run+0xbf/0xf0 [bluetooth]
[<ffffffffa01709b0>] ? hci_init2_req+0x720/0x720 [bluetooth]
[<ffffffffa016ea06>] __hci_req_sync+0xd6/0x1c0 [bluetooth]
[<ffffffff8108ee10>] ? try_to_wake_up+0x2b0/0x2b0
[<ffffffff8150e3f0>] ? usb_autopm_put_interface+0x30/0x40
[<ffffffffa016fad5>] hci_dev_open+0x275/0x2e0 [bluetooth]
[<ffffffffa0182752>] hci_sock_ioctl+0x1f2/0x3f0 [bluetooth]
[<ffffffff815c6050>] sock_do_ioctl+0x30/0x70
[<ffffffff815c75f9>] sock_ioctl+0x79/0x2f0
[<ffffffff811a8046>] do_vfs_ioctl+0x96/0x560
[<ffffffff811a85a1>] SyS_ioctl+0x91/0xb0
[<ffffffff816d989d>] system_call_fastpath+0x1a/0x1f
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The length check is invalid since the length varies with type of
info response.
This was introduced by the commit cb3b3152b2
Because of this, l2cap info rsp is not handled and command reject is sent.
> ACL data: handle 11 flags 0x02 dlen 16
L2CAP(s): Info rsp: type 2 result 0
Extended feature mask 0x00b8
Enhanced Retransmission mode
Streaming mode
FCS Option
Fixed Channels
< ACL data: handle 11 flags 0x00 dlen 10
L2CAP(s): Command rej: reason 0
Command not understood
Cc: stable@vger.kernel.org
Signed-off-by: Jaganath Kanakkassery <jaganath.k@samsung.com>
Signed-off-by: Chan-Yeol Park <chanyeol.park@samsung.com>
Acked-by: Johan Hedberg <johan.hedberg@intel.com>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The current regdomain was not always set by the core. This causes
cards with a custom regulatory domain to ignore user initiated changes
if done before the card was registered.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Acked-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
John W. Linville says:
====================
This is another batch of fixes intended for the 3.11 stream. FWIW,
this is the first request with fixes from the mac80211 and iwlwifi
trees as well.
Regarding the mac80211 bits, Johannes says:
"Here I have a fix for RSSI thresholds in mesh, two minstrel fixes from
Felix, an nl80211 fix from Michal and four various fixes I did myself."
As for the iwlwifi bits, Johannes says:
"Here I have a fix for debugfs directory creation (causing a spurious
error message), two scanning fixes from David Spinadel, an LED fix and
two patches related to a BA session problem that eventually caused
firmware crashes from Emmanuel and a small BT fix for older devices as
well as a workaround for a firmware problem with APs with very small
beacon intervals from myself."
Along with those:
Arend van Spriel addresses a lock-up and a NULL pointer dereference
in brcmfmac.
Daniel Drake fixes an unhandled interrupt during device tear down
in mwifiex.
Larry Finger corrects a wil6210 build error.
Oleksij Rempel fixes two ath9k_htc problems related to keeping the
driver and firmware in sync.
Solomon Peachy gives us a cw1200 fix to avoid an oops in monitor mode.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
build_skb() specifies that the data parameter must come from a kmalloc'd
area, this is only true if frag_size equals 0, because then build_skb()
will use kzsize(data) to figure out the actual data size. Update the
comment to reflect that special condition.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the <= max condition in the for loop, it will be always go 1
element further than needed. If the condition for the while loop is
never met, then max is MAX_STAT_DEPTH, and for loop will walk off the
end of nodesizes[].
Signed-off-by: Jerry Snitselaar <jerry.snitselaar@oracle.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
My commit:
commit 12e7f51702
Author: Stanislaw Gruszka <sgruszka@redhat.com>
Date: Thu Feb 28 10:55:26 2013 +0100
mac80211: cleanup generic suspend/resume procedures
removed check for deleting MONITOR and AP_VLAN when suspend. That can
cause a crash (i.e. in iwlagn_mac_remove_interface()) since we remove
interface in the driver that we did not add before.
Reference:
http://marc.info/?l=linux-kernel&m=137391815113860&w=2
Bisected-by: Ortwin Glück <odi@odi.ch>
Reported-and-tested-by: Ortwin Glück <odi@odi.ch>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Pablo Neira Ayuso says:
====================
The following patchset contains Netfilter fixes for your net tree,
they are:
* Fix potential NULL dereference in the socket match if revision 0
is used, from Eric Dumazet.
* Fix missing expectation NAT initialization that results in dumping
the NAT part via ctnetlink, thus leading to problems in expectation
synchronization through conntrackd, from myself.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is intended to avoid the buffering to non-assoc mesh STA
and also to avoid the triggering of frame to non-assoc mesh STA which
could cause kernel panic in specific hw.
One of the examples, is kernel panic happens to ath9k if user space
inserts the mesh STA and not proceed with the SAE and AMPE, and later
the same mesh STA is detected again. The sta_state of the mesh STA remains
at IEEE80211_STA_NONE and if the ieee80211_sta_ps_deliver_wakeup is called
and subsequently the ath_tx_aggr_wakeup, the kernel panic due to
ath_tx_node_init is not called before to initialize the require data
structures.
This issue is reported by Cedric Voncken before.
http://www.spinics.net/lists/linux-wireless/msg106342.html
[<831ea6b4>] ath_tx_aggr_wakeup+0x44/0xcc [ath9k]
[<83084214>] ieee80211_sta_ps_deliver_wakeup+0xb8/0x208 [mac80211]
[<830b9824>] ieee80211_mps_sta_status_update+0x94/0x108 [mac80211]
[<83099398>] ieee80211_sta_ps_transition+0xc94/0x34d8 [mac80211]
[<8022399c>] nf_iterate+0x98/0x104
[<8309bb60>] ieee80211_sta_ps_transition+0x345c/0x34d8 [mac80211]
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
- Fix a regression against NFSv4 FreeBSD servers when creating a new file
- Fix another regression in rpc_client_register()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=XE+7
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Fix a regression against NFSv4 FreeBSD servers when creating a new
file
- Fix another regression in rpc_client_register()
* tag 'nfs-for-3.11-3' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4: Fix a regression against the FreeBSD server
SUNRPC: Fix another issue with rpc_client_register()
commit 9f00b2e7cf ("bridge: only expire the mdb entry when query is
received") added a nasty bug as an active timer can be reinitialized.
setup_timer() must be done once, no matter how many time mod_timer()
is called. br_multicast_new_group() is the right place to do this.
Reported-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Diagnosed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Limit the min/max value passed to the
/proc/sys/net/ipv4/tcp_syn_retries.
Signed-off-by: Michal Tesar <mtesar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot found following error:
net/built-in.o: In function `nci_spi_send':
>> spi.c:(.text+0x19a76f): undefined reference to `crc_ccitt'
Add CRC_CCITT module to Kconfig to fix it
Reported-by: kbuild test robot.
Signed-off-by: Frederic Danis <frederic.danis@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull networking fixes from David Miller:
"A couple interesting SKB fragment handling fixes, plus the usual small
bits here and there:
1) Fix 64-bit divide build failure on 32-bit platforms in mlx5, from
Tim Gardner.
2) Get rid of a stupid reimplementation on "%*phC" in our sysfs MAC
address printing helper.
3) Fix NETIF_F_SG capability advertisement in hyperv driver, if the
device can't do checksumming offloads then it shouldn't say it can
do SG either. From Haiyang Zhang.
4) bgmac needs to depend on PHYLIB, from Hauke Mehrtens.
5) Don't leak DMA mappings on mapping failures, from Neil Horman.
6) We need to reset the transport header of SKBs in ipv4 before we
attempt to perform early socket demux, just like ipv6 does. From
Eric Dumazet.
7) Add missing locking on vxlan device removal, from Stephen
Hemminger.
8) xen-netfront has to make two passes over an SKB to prepare it for
transfer. One pass calculates the number of slots needed, the
second massages the SKB and fills the slots. Unfortunately, the
first pass doesn't calculate the number of slots properly so we
can end up trying to build a MAX_SKB_FRAGS + 1 SKB which doesn't
work out so well. Fix from Jan Beulich with help and discussion
with several others.
9) Fix a similar problem in tun and macvtap, which have to split up
scatter-gather elements at PAGE_SIZE boundaries. Don't do
zerocopy if it would result in a > MAX_SKB_FRAGS skb. Fixes from
Jason Wang.
10) On receive, once we've decoded the VLAN state completely, clear
skb->vlan_tci. Otherwise demuxed tunnels underneath can trigger
the VLAN code again, corrupting the packet. Fix from Eric
Dumazet"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
vlan: fix a race in egress prio management
vlan: mask vlan prio bits
macvtap: do not zerocopy if iov needs more pages than MAX_SKB_FRAGS
tuntap: do not zerocopy if iov needs more pages than MAX_SKB_FRAGS
pkt_sched: sch_qfq: remove a source of high packet delay/jitter
xen-netfront: pull on receive skb may need to happen earlier
vxlan: add necessary locking on device removal
hyperv: Fix the NETIF_F_SG flag setting in netvsc
net: Fix sysfs_format_mac() code duplication.
be2net: Fix to avoid hardware workaround when not needed
macvtap: do not assume 802.1Q when send vlan packets
macvtap: fix the missing ret value of TUNSETQUEUE
ipv4: set transport header earlier
mlx5 core: Fix __udivdi3 when compiling for 32 bit arches
bgmac: add dependency to phylib
net/irda: fixed style issues in irlan_eth
ethtool: fixed trailing statements in ethtool
ndisc: bool initializations should use true and false
atl1e: unmap partially mapped skb on dma error and free skb
egress_priority_map[] hash table updates are protected by rtnl,
and we never remove elements until device is dismantled.
We have to make sure that before inserting an new element in hash table,
all its fields are committed to memory or else another cpu could
find corrupt values and crash.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 48cc32d38a
("vlan: don't deliver frames for unknown vlans to protocols")
Florian made sure we set pkt_type to PACKET_OTHERHOST
if the vlan id is set and we could find a vlan device for this
particular id.
But we also have a problem if prio bits are set.
Steinar reported an issue on a router receiving IPv6 frames with a
vlan tag of 4000 (id 0, prio 2), and tunneled into a sit device,
because skb->vlan_tci is set.
Forwarded frame is completely corrupted : We can see (8100:4000)
being inserted in the middle of IPv6 source address :
16:48:00.780413 IP6 2001:16d8:8100:4000:ee1c:0:9d9:bc87 >
9f94:4d95:2001:67c:29f4::: ICMP6, unknown icmp6 type (0), length 64
0x0000: 0000 0029 8000 c7c3 7103 0001 a0ae e651
0x0010: 0000 0000 ccce 0b00 0000 0000 1011 1213
0x0020: 1415 1617 1819 1a1b 1c1d 1e1f 2021 2223
0x0030: 2425 2627 2829 2a2b 2c2d 2e2f 3031 3233
It seems we are not really ready to properly cope with this right now.
We can probably do better in future kernels :
vlan_get_ingress_priority() should be a netdev property instead of
a per vlan_dev one.
For stable kernels, lets clear vlan_tci to fix the bugs.
Reported-by: Steinar H. Gunderson <sesse@google.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
QFQ+ inherits from QFQ a design choice that may cause a high packet
delay/jitter and a severe short-term unfairness. As QFQ, QFQ+ uses a
special quantity, the system virtual time, to track the service
provided by the ideal system it approximates. When a packet is
dequeued, this quantity must be incremented by the size of the packet,
divided by the sum of the weights of the aggregates waiting to be
served. Tracking this sum correctly is a non-trivial task, because, to
preserve tight service guarantees, the decrement of this sum must be
delayed in a special way [1]: this sum can be decremented only after
that its value would decrease also in the ideal system approximated by
QFQ+. For efficiency, QFQ+ keeps track only of the 'instantaneous'
weight sum, increased and decreased immediately as the weight of an
aggregate changes, and as an aggregate is created or destroyed (which,
in its turn, happens as a consequence of some class being
created/destroyed/changed). However, to avoid the problems caused to
service guarantees by these immediate decreases, QFQ+ increments the
system virtual time using the maximum value allowed for the weight
sum, 2^10, in place of the dynamic, instantaneous value. The
instantaneous value of the weight sum is used only to check whether a
request of weight increase or a class creation can be satisfied.
Unfortunately, the problems caused by this choice are worse than the
temporary degradation of the service guarantees that may occur, when a
class is changed or destroyed, if the instantaneous value of the
weight sum was used to update the system virtual time. In fact, the
fraction of the link bandwidth guaranteed by QFQ+ to each aggregate is
equal to the ratio between the weight of the aggregate and the sum of
the weights of the competing aggregates. The packet delay guaranteed
to the aggregate is instead inversely proportional to the guaranteed
bandwidth. By using the maximum possible value, and not the actual
value of the weight sum, QFQ+ provides each aggregate with the worst
possible service guarantees, and not with service guarantees related
to the actual set of competing aggregates. To see the consequences of
this fact, consider the following simple example.
Suppose that only the following aggregates are backlogged, i.e., that
only the classes in the following aggregates have packets to transmit:
one aggregate with weight 10, say A, and ten aggregates with weight 1,
say B1, B2, ..., B10. In particular, suppose that these aggregates are
always backlogged. Given the weight distribution, the smoothest and
fairest service order would be:
A B1 A B2 A B3 A B4 A B5 A B6 A B7 A B8 A B9 A B10 A B1 A B2 ...
QFQ+ would provide exactly this optimal service if it used the actual
value for the weight sum instead of the maximum possible value, i.e.,
11 instead of 2^10. In contrast, since QFQ+ uses the latter value, it
serves aggregates as follows (easy to prove and to reproduce
experimentally):
A B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 A A A A A A A A A A B1 B2 ... B10 A A ...
By replacing 10 with N in the above example, and by increasing N, one
can increase at will the maximum packet delay and the jitter
experienced by the classes in aggregate A.
This patch addresses this issue by just using the above
'instantaneous' value of the weight sum, instead of the maximum
possible value, when updating the system virtual time. After the
instantaneous weight sum is decreased, QFQ+ may deviate from the ideal
service for a time interval in the order of the time to serve one
maximum-size packet for each backlogged class. The worst-case extent
of the deviation exhibited by QFQ+ during this time interval [1] is
basically the same as of the deviation described above (but, without
this patch, QFQ+ suffers from such a deviation all the time). Finally,
this patch modifies the comment to the function qfq_slot_insert, to
make it coherent with the fact that the weight sum used by QFQ+ can
now be lower than the maximum possible value.
[1] P. Valente, "Extending WF2Q+ to support a dynamic traffic mix",
Proceedings of AAA-IDEA'05, June 2005.
Signed-off-by: Paolo Valente <paolo.valente@unimore.it>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull phase two of __cpuinit removal from Paul Gortmaker:
"With the __cpuinit infrastructure removed earlier, this group of
commits only removes the function/data tagging that was done with the
various (now no-op) __cpuinit related prefixes.
Now that the dust has settled with yesterday's v3.11-rc1, there
hopefully shouldn't be any new users leaking back in tree, but I think
we can leave the harmless no-op stubs there for a release as a
courtesy to those who still have out of tree stuff and weren't paying
attention.
Although the commits are against the recent tag to allow for minor
context refreshes for things like yesterday's v3.11-rc1~ slab content,
the patches have been largely unchanged for weeks, aside from such
trivial updates.
For detail junkies, the largely boring and mostly irrelevant history
of the patches can be viewed at:
http://git.kernel.org/cgit/linux/kernel/git/paulg/cpuinit-delete.git
If nothing else, I guess it does at least demonstrate the level of
involvement required to shepherd such a treewide change to completion.
This is the same repository of patches that has been applied to the
end of the daily linux-next branches for the past several weeks"
* 'cpuinit_phase2' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (28 commits)
block: delete __cpuinit usage from all block files
drivers: delete __cpuinit usage from all remaining drivers files
kernel: delete __cpuinit usage from all core kernel files
rcu: delete __cpuinit usage from all rcu files
net: delete __cpuinit usage from all net files
acpi: delete __cpuinit usage from all acpi files
hwmon: delete __cpuinit usage from all hwmon files
cpufreq: delete __cpuinit usage from all cpufreq files
clocksource+irqchip: delete __cpuinit usage from all related files
x86: delete __cpuinit usage from all x86 files
score: delete __cpuinit usage from all score files
xtensa: delete __cpuinit usage from all xtensa files
openrisc: delete __cpuinit usage from all openrisc files
m32r: delete __cpuinit usage from all m32r files
hexagon: delete __cpuinit usage from all hexagon files
frv: delete __cpuinit usage from all frv files
cris: delete __cpuinit usage from all cris files
metag: delete __cpuinit usage from all metag files
tile: delete __cpuinit usage from all tile files
sh: delete __cpuinit usage from all sh files
...
Pull nfsd bugfixes from Bruce Fields:
"Just three minor bugfixes"
* 'for-3.11' of git://linux-nfs.org/~bfields/linux:
svcrdma: underflow issue in decode_write_list()
nfsd4: fix minorversion support interface
lockd: protect nlm_blocked access in nlmsvc_retry_blocked
It's just a duplicate implementation of "%*phC". Thanks to Joe
Perches for showing that we had exactly this support in the
lib/vsprintf.c code already.
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 45f00f99d6 ("ipv4: tcp: clean up tcp_v4_early_demux()") added a
performance regression for non GRO traffic, basically disabling
IP early demux.
IPv6 stack resets transport header in ip6_rcv() before calling
IP early demux in ip6_rcv_finish(), while IPv4 does this only in
ip_local_deliver_finish(), _after_ IP early demux.
GRO traffic happened to enable IP early demux because transport header
is also set in inet_gro_receive()
Instead of reverting the faulty commit, we can make IPv4/IPv6 behave the
same : transport_header should be set in ip_rcv() instead of
ip_local_deliver_finish()
ip_local_deliver_finish() can also use skb_network_header_len() which is
faster than ip_hdrlen()
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When priv_sta == NULL, mi->prev_sample is dereferenced too early. Move
the assignment further down, after the rate_control_send_low call.
Reported-by: Krzysztof Mazur <krzysiek@podlesie.net>
Cc: stable@vger.kernel.org # 3.10
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
The duplicate retransmission detection code in mac80211
erroneously attempts to do the check for every frame,
even frames that don't have a sequence control field or
that don't use it (QoS-Null frames.)
This is problematic because it causes the code to access
data beyond the end of the SKB and depending on the data
there will drop packets erroneously.
Correct the code to not do duplicate detection for such
frames.
I found this error while testing AP powersave, it lead
to retransmitted PS-Poll frames being dropped entirely
as the data beyond the end of the SKB was always zero.
Cc: stable@vger.kernel.org [all versions]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
RSSI threshold value used for mesh peering should be in
negative value. After range checks to mesh parameters is
introduced, this is not allowed. Fix this.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
