Fix the non-linear memory mapping done via remap_file_pages() -- it
didn't work on any MIPS CPU because the page offset clashing with
_PAGE_FILE and some other page protection bits which should have been left
zeros for this kind of pages.
Signed-off-by: Konstantin Baydarov <kbaidarov@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With 64-bit physical address enabled, 'swapon' was causing kernel oops on
Alchemy CPUs (MIPS32) because of the swap entry type field corrupting the
_PAGE_FILE bit in 'pte_low' field. So, switch to storing the swap entry in
'pte_high' field using all its bits except _PAGE_GLOBAL and _PAGE_VALID which
gives 25 bits for the swap entry offset.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A while ago prom_prepare_cpus was replaced by plat_prepare_cpus but
the declaration has stayed unchanged.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Increase alignment of BogoMIPS loop to 8 bytes. Having the delay loop
overlap cache line boundaries may cause instable delays.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We can race and misset the suspend bit if iscsi_write_space is
called then iscsi_send returns with a failure indicating
there is no space.
To handle this this patch returns a error upwards allowing xmitworker
to decide if we need to try and transmit again. For the no
write space case xmitworker will not retry, and instead
let iscsi_write_space queue it back up if needed (this relies
on the work queue code to properly requeue us if needed).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If recovery failed or we are in recovery only overwrite the state
if we are going to terminate the session or if we logged back in.
STOP_CONN_SUSPEND and conn_cnt are not used. We only support
a single connection session ATM, so cleanup that code while
we are working around it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
My router blew up earlier, but exhibited some interesting behaviour during
its dying moments. It was broadcasting beacons but wouldn't respond to
any authentication requests.
I noticed that softmac wasn't playing nice with this, as I couldn't make it try
to connect to other networks after it had timed out authenticating to my ill
router.
To resolve this, I modified the softmac event/notify API to pass the event
code to the callback, so that callbacks being notified from
IEEE80211SOFTMAC_EVENT_ANY masks can make some judgement. In this case, the
ieee80211softmac_assoc callback needs to make a decision based upon whether
the association passed or failed.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch finishes of the partially-complete shared key authentication
implementation in softmac.
The complication here is that we need to encrypt a management frame during
the authentication process. I don't think there are any other scenarios where
this would have to happen.
To get around this without causing too many headaches, we decided to just use
software encryption for this frame. The softmac config option now selects
IEEE80211_CRYPT_WEP so that we can ensure this available. This also involved
a modification to some otherwise unused ieee80211 API.
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
From: Al Viro <viro@zeniv.linux.org.uk>
uml __user annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Jeff Dike <jdike@addtoit.com>
Add an empty asm/irqflags.h, which seems to satisfy the lock validator enough
that UML builds.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Andrew Morton <akpm@osdl.org>
drivers/rtc/rtc-m48t86.c: In function `m48t86_rtc_read_time':
drivers/rtc/rtc-m48t86.c:51: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:55: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:56: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:57: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:58: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:60: error: structure has no member named `ia64_mv'
readb() and writeb() are macros on ia64.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
After removal of fixup_cpu_present_map() function Alpha ended up with an empty
cpu_present_map, so secondary CPUs on SMP systems are not being started.
Worse, on some platforms we route interrupts to secondary CPUs using
cpu_possible_map which is still populated properly. As a result, these
interrupts go nowhere so the machines like DP264 aren't able to boot even with
a primary CPU.
Fixed basically by s/cpu_present_mask/cpu_present_map/.
Thanks to Ernst Herzberg for reporting the bug and testing the fix.
Cc: Ernst Herzberg <list-lkml@net4u.de>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Ralf Baechle <ralf@linux-mips.org>
<linux/mmzone.h> uses PAGE_SIZE, PAGE_SHIFT from <asm/page.h> without
including that header itself. For some sparsemem configurations this may
result in build errors like:
CC init/initramfs.o
In file included from include/linux/gfp.h:4,
from include/linux/slab.h:15,
from include/linux/percpu.h:4,
from include/linux/rcupdate.h:41,
from include/linux/dcache.h:10,
from include/linux/fs.h:226,
from init/initramfs.c:2:
include/linux/mmzone.h:498:22: warning: "PAGE_SHIFT" is not defined
In file included from include/linux/gfp.h:4,
from include/linux/slab.h:15,
from include/linux/percpu.h:4,
from include/linux/rcupdate.h:41,
from include/linux/dcache.h:10,
from include/linux/fs.h:226,
from init/initramfs.c:2:
include/linux/mmzone.h:526: error: `PAGE_SIZE' undeclared here (not in a function)
include/linux/mmzone.h: In function `__pfn_to_section':
include/linux/mmzone.h:573: error: `PAGE_SHIFT' undeclared (first use in this function)
include/linux/mmzone.h:573: error: (Each undeclared identifier is reported only once
include/linux/mmzone.h:573: error: for each function it appears in.)
include/linux/mmzone.h: In function `pfn_valid':
include/linux/mmzone.h:578: error: `PAGE_SHIFT' undeclared (first use in this function)
make[1]: *** [init/initramfs.o] Error 1
make: *** [init] Error 2
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Seems-reasonable-to: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
The path grouping can fail due to non-unique pathgroup-IDs. The source for
the CPU-ID part of the ID was incorrectly specified on 64 bit systems.
Additionally, the length of the ID was too large due to incorrect data packing
declaration. Fix CPU-ID lowcore address and add missing packing declaration.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since rb_insert_color() is part of the _public_ API, while the others are
purely internal, switch to be consistent with that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Replacing mistyped "buad" with "baud" where applicable.
Signed-off-by: Horst Schirmeier <horst@schirmeier.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The rest of the file uses these types instead of C99 types.
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3540/1: ixp23xx: deal with gap in interrupt bitmasks
[ARM] 3539/1: ixp23xx: fix __arch_ixp23xx_is_coherent() for A1 stepping
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Fix D-cache corruption in mremap
[SPARC64]: Make smp_processor_id() functional before start_kernel()
Patch from Lennert Buytenhek
The current __ixp23xx_arch_is_coherent() check assumes that the
lower byte of IXP23XX_PRODUCT_ID is identical to the lower byte of
processor_id, but this is not the case, and because of this we were
incorrectly enabling coherency on A1 stepping CPUs.
Stepping A1 of the ixp2350, which has a PRODUCT_ID of 0x401, has '02'
in the lower byte of processor_id, while A2, with a PRODUCT_ID of
0x402, has '04' in the lower byte of processor_id.
So, to check for >= A2, we really need to check the lower byte of
processor_id against >= 4.
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we move a mapping from one virtual address to another,
and this changes the virtual color of the mapping to those
pages, we can see corrupt data due to D-cache aliasing.
Check for and deal with this by overriding the move_pte()
macro. Set things up so that other platforms can cleanly
override the move_pte() macro too.
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[MIPS] Treat R14000 like R10000.
[MIPS] Remove EXPERIMENTAL from PAGE_SIZE_16KB
[MIPS] Update/Fix instruction definitions
[MIPS] DSP and MDMX share the same config flag bit.
[MIPS] Fix deadlock on MP with cache aliases.
[MIPS] Use generic STABS_DEBUG macro.
[MIPS] Create consistency in "system type" selection.
[MIPS] Use generic DWARF_DEBUG
[MIPS] Fix kgdb exception handler from user mode.
[MIPS] Update struct sigcontext member names
[MIPS] Update/fix futex assembly
[MIPS] Remove support for sysmips(2) SETNAME and MIPS_RDNVRAM operations.
[MIPS] Fix detection and handling of the 74K processor.
[MIPS] Add missing 34K processor IDs
[MIPS] Fix marking buddy of pte global for MIPS32 w/36-bit physical address
[MIPS] AU1xxx mips_timer_interrupt() fixes
[MIPS] Fix typo
A small bugfix for up to now unused instruction definitions, and a
somewhat larger update to cover MIPS32R2 instructions.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rename the 64-bit sc_hi and sc_lo arrays to use the same names
as the 32-bit struct sigcontext (sc_mdhi, sc_hi1, et cetera).
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Implement futex_atomic_op_inuser() operation
o Don't use the R10000-ll/sc bug workaround version for every processor.
branch likely is deprecated and some historic ll/sc processors don't
implement it. In any case it's slow.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Nothing exciting; Linux just didn't know it yet so this is most adding
a value to a case statement.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
In case of CONFIG_64BIT_PHYS_ADDR, set_pte() and pte_clear() functions
only set _PAGE_GLOBAL bit in the pte_low field of the buddy PTEs,
forgetting to propagate ito to pte_high. Thus, the both pages might not
really be made global for the CPU (since it AND's the G-bit of the
odd / even PTEs together to decide whether they're global or not). Thus,
if only a single page is allocated via vmalloc() or ioremap(), it's not
really global for CPU (and it must be, since this is kernel mapping),
and thus its ASID is compared against the current process' one -- so,
we'll get into trouble sooner or later... Also, pte_none() will fail
on global pages because _PAGE_GLOBAL bit is set in both pte_low and
pte_high, and pte_val() will return u64 value consisting of those fields
concateneted.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The ARM Architecture Reference Manual lists bit 4 of the PMD as "implementation
defined" and it must be set to zero on Intel XScale CPUs or the cache does
not behave properly. Found by Mike Rapoport while debugging a flash issue
on the PXA255:
http://marc.10east.com/?l=linux-arm-kernel&m=114845287600782&w=1
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Andrew Morton <akpm@osdl.org>
Move the forward decl outside the ifdef, since we use it in both legs.
Should fix the spacr64 build error reported in
http://bugzilla.kernel.org/show_bug.cgi?id=6625
Acked-by: "David S. Miller" <davem@davemloft.net>
Cc: Cedric Pellerin <cedric@bidouillesoft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Andrew Morton <akpm@osdl.org>
Revert commit ff4da2e262.
It broke APM suspend, probably because APM doesn't switch back to a VT
when suspending.
Tracked down by Matt Mackall <mpm@selenic.com>
Rafael sayeth:
"It only fixed the theoretical issue that a quick-handed user could
switch to X after processes have been frozen and before the devices
are suspended.
With the current userland suspend tools it shouldn't be necessary."
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
ia32_setup_arg_pages would ignore the passed in random stack top
and use its own static value.
Now it uses the 8bit of randomness native i386 would use too.
This indirectly fixes mmap randomization for 32bit processes too,
which depends on the stack randomization.
Should also give slightly better virtual cache colouring and
possibly better performance with HyperThreading.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] VIA PT880 Ultra support.
[AGPGART] Fix Nforce3 suspend on amd64.
[AGPGART] Enable SIS AGP driver on x86-64 for EM64T systems
Ram devices get the extra capability of MTD_NO_ERASE - not requiring
an explicit erase before writing to it. Currently only mtdblock uses
this capability. Rest of the patch is a simple text replacement.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
No mtd user should ever check for the device type. Instead, device features
should be checked by the flags - if at all.
As a first step towards type removal, change MTD_ROM into MTD_GENERIC_TYPE.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
Remove the numbered SW_* entries from the input system and assign names
to the existing users.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The raw read/write access to NAND (without ECC) has been changed in the
NAND rework. Expose the new way - setting the file mode via ioctl - to
userspace. Also allow to read out the ecc statistics information so userspace
tools can see that bitflips happened and whether errors where correctable
or not. Also expose the number of bad blocks for the partition, so nandwrite
can check if the data fits into the parition before writing to it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hopefully the last iteration on this!
The handling of out of band data on NAND was accompanied by tons of fruitless
discussions and halfarsed patches to make it work for a particular
problem. Sufficiently annoyed by I all those "I know it better" mails and the
resonable amount of discarded "it solves my problem" patches, I finally decided
to go for the big rework. After removing the _ecc variants of mtd read/write
functions the solution to satisfy the various requirements was to refactor the
read/write _oob functions in mtd.
The major change is that read/write_oob now takes a pointer to an operation
descriptor structure "struct mtd_oob_ops".instead of having a function with at
least seven arguments.
read/write_oob which should probably renamed to a more descriptive name, can do
the following tasks:
- read/write out of band data
- read/write data content and out of band data
- read/write raw data content and out of band data (ecc disabled)
struct mtd_oob_ops has a mode field, which determines the oob handling mode.
Aside of the MTD_OOB_RAW mode, which is intended to be especially for
diagnostic purposes and some internal functions e.g. bad block table creation,
the other two modes are for mtd clients:
MTD_OOB_PLACE puts/gets the given oob data exactly to/from the place which is
described by the ooboffs and ooblen fields of the mtd_oob_ops strcuture. It's
up to the caller to make sure that the byte positions are not used by the ECC
placement algorithms.
MTD_OOB_AUTO puts/gets the given oob data automaticaly to/from the places in
the out of band area which are described by the oobfree tuples in the ecclayout
data structre which is associated to the devicee.
The decision whether data plus oob or oob only handling is done depends on the
setting of the datbuf member of the data structure. When datbuf == NULL then
the internal read/write_oob functions are selected, otherwise the read/write
data routines are invoked.
Tested on a few platforms with all variants. Please be aware of possible
regressions for your particular device / application scenario
Disclaimer: Any whining will be ignored from those who just contributed "hot
air blurb" and never sat down to tackle the underlying problem of the mess in
the NAND driver grown over time and the big chunk of work to fix up the
existing users. The problem was not the holiness of the existing MTD
interfaces. The problems was the lack of time to go for the big overhaul. It's
easy to add more mess to the existing one, but it takes alot of effort to go
for a real solution.
Improvements and bugfixes are welcome!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Most of those macros are unused and the used ones just obfuscate
the code. Remove them and fixup all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The nand_oobinfo structure is not fitting the newer error correction
demands anymore. Replace it by struct nand_ecclayout and fixup the users
all over the place. Keep the nand_oobinfo based ioctl for user space
compability reasons.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The info structure for out of band data was copied into
the mtd structure. Make it a pointer and remove the ability
to set it from userspace. The position of ecc bytes is
defined by the hardware and should not be changed by software.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The platform structure was lacking an oobinfo field.
The NDFC driver had some remains from another tree.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds new device ids for MCP61 and MCP65 chips.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some driver wants to use CMSPAR, but it was missing on alpha and powerpc.
This adds it, with the same value as every other architecture uses.
(akpm: fixes the build of an upcoming gregkh USB patch)
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modularize the write function and reorganaize the internal buffer
management. Remove obsolete chip options and fixup all affected
users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Split the core of the read function out and implement
seperate handling functions for software and hardware
ECC.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add read/write function pointers to struct nand_ecc_ctrl to
prepare the modulaization of nand_read/write functions. The
current implementation handles every type of ecc mode
software/hardware and all kinds of strange ecc placement
schemes in one switch/if construct. Thats too complex to
maintain and too inflexible to expand. Modularization will
also shorten the code pathes of the read/write functions.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
FLASH - especially NAND FLASH - will become less reliable
and bit flips more likely. Add an ECC statistics struct
to struct mtd_info to keep track of this.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The nand driver has a superflous read ready / command
delay in the read functions. This was added to handle
chips which have an automatic read forward. Newer
chips do not have this functionality anymore. Add this
option to avoid the delay / I/O operation. Mark all
large page chips with the new option flag.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch revives pci_find_ext_capability (has been disabled a couple month
ago since it was not used anywhere. See http://lkml.org/lkml/2006/1/20/247).
It will now be used by the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>
drivers/pci/pci.c | 3 +--
include/linux/pci.h | 2 ++
2 files changed, 3 insertions(+), 2 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The previous change of the command / hardware control allows to
remove the write_byte/word functions completely, as their only
user were nand_command and nand_command_lp.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The hwcontrol function enforced a step by step state machine
for any kind of hardware chip access. Let the hardware driver
know which control bits are set and inform it about a change
of the control lines. Let the hardware driver write out the
command and address bytes directly. This gives a peformance
advantage for address bus controlled chips and simplifies the
quirks in the hardware drivers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
These flags are needed by userspace - move them outside __KERNEL__
(Pointed out by dwmw2)
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MTD clients are agnostic of FLASH which needs ECC suppport.
Remove the functions and fixup the callers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
First step of modularizing ECC support.
- Move ECC related functionality into a seperate embedded data structure
- Get rid of the hardware dependend constants to simplify new ECC models
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The NAND driver used a mix of unsigned char, u_char amd uint8_t
data types. Consolidate to uint8_t usage
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Replace the chip lock by a the controller lock. For simple drivers a
dummy controller structure is created by the scan code.
This simplifies the locking algorithm in nand_get/release_chip().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Using asm-generic/dma-mapping.h does not work because pushing
the call down to pci_alloc_coherent() causes the gfp_t argument
of dma_alloc_coherent() to be ignored.
Fix this by implementing things directly, and adding a gfp_t
argument we can use in the internal call down to the PCI DMA
implementation of pci_alloc_coherent().
This fixes massive memory corruption when using the sound driver
layer, which passes things like __GFP_COMP down into these
routines and (correctly) expects that to work.
Signed-off-by: David S. Miller <davem@davemloft.net>
o Add a flag MTD_BIT_WRITEABLE for devices that allow single bits to be
cleared.
o Replace MTD_PROGRAM_REGIONS with a cleared MTD_BIT_WRITEABLE flag for
STMicro and Intel Sibley flashes with internal ECC. Those flashes
disallow clearing of single bits, unlike regular NOR flashes, so the
new flag models their behaviour better.
o Remove MTD_ECC. After the STMicro/Sibley merge, this flag is only set
and never checked.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
At least two flashes exists that have the concept of a minimum write unit,
similar to NAND pages, but no other NAND characteristics. Therefore, rename
the minimum write unit to "writesize" for all flashes, including NAND.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
Two flags exist to decide whether a device is writeable or not. None of
those two flags is checked for independently, so they are clearly redundant,
if not an invitation to bugs. This patch removed both of them, replacing
them with a single new flag.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
This patch enables agpgart on a Via "PT880 Ultra" based motherboard
(Asus P4V800D-X). The PCI ID of the PT880 Ultra is 0x0308 instead of
0x0258 of the PT880.
The patched via-agp passes testgart.
Signed-off-by: Magnus Kessler <Magnus.Kessler@gmx.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Andy added code to buddy allocator which does not require the zone's
endpoints to be aligned to MAX_ORDER. An issue is that the buddy allocator
requires the node_mem_map's endpoints to be MAX_ORDER aligned. Otherwise
__page_find_buddy could compute a buddy not in node_mem_map for partial
MAX_ORDER regions at zone's endpoints. page_is_buddy will detect that
these pages at endpoints are not PG_buddy (they were zeroed out by bootmem
allocator and not part of zone). Of course the negative here is we could
waste a little memory but the positive is eliminating all the old checks
for zone boundary conditions.
SPARSEMEM won't encounter this issue because of MAX_ORDER size constraint
when SPARSEMEM is configured. ia64 VIRTUAL_MEM_MAP doesn't need the logic
either because the holes and endpoints are handled differently. This
leaves checking alloc_remap and other arches which privately allocate for
node_mem_map.
Signed-off-by: Bob Picco <bob.picco@hp.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix some outstanding issues with the pxa2xx_spi driver when running on a
PXA270:
- Wrong timeout calculation in the setup function due to different
peripheral clock rates in the PXAxxx family.
- Bad handling of SSSR_TFS interrupts in interrupt_transfer function.
- Added locking to interface between the pump_messages workqueue and the
pump_transfers tasklet.
Much thanks to Juergen Beisert for the extensive testing on the PXA270.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hardware based SPI driver for Samsung S3C24XX SoC systems
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SPI driver for SPI by GPIO on the Samsung S3C24XX series of SoC processors.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- remove the following global function that is both unused and
unimplemented:
- register_firmware()
- make the following needlessly global function static:
- firmware_class_uevent()
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This driver supports the SPI controller on the MPC83xx SoC devices from
Freescale. Note, this driver supports only the simple shift register SPI
controller and not the descriptor based CPM or QUICCEngine SPI controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not flush queues then block session. This will cause commands
to needlessly swing around on us and remove goofy
recovery_failed field and replace with state value.
And do not start recovery from within the host reset function.
This causeis too many problems becuase open-iscsi was desinged to
call out to userspace then have userpscae decide if we should
go into recovery or kill the session.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[SCTP]: Allow linger to abort 1-N style sockets.
[SCTP]: Validate the parameter length in HB-ACK chunk.
[SCTP]: Respect the real chunk length when walking parameters.
[SCTP]: A better solution to fix the race between sctp_peeloff() and
[SCTP]: Set sk_err so that poll wakes up after a non-blocking connect failure.
Patch from Catalin Marinas
Recent patches introduced the write_can_lock() call in the kernel/ptrace.c
file. Implement the __raw_* variants on ARM (SMP) as well.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Pavel Pisa
There has been problems that for some paths that clock are not stopped
during new command programming and initiation. Result is issuing
of incorrect command to the card. Some other problems are cleaned too.
Noisy report of known ERRATUM #4 has been suppressed.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When performing bound checks during the parameter processing, we
want to use the real chunk and paramter lengths for bounds instead
of the rounded ones. This prevents us from potentially walking of
the end if the chunk length was miscalculated. We still use rounded
lengths when advancing the pointer. This was found during a
conformance test that changed the chunk length without modifying
parameters.
Signed-off-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Device node major/minor numbers are just stored in the payload of a single
data node. Just extend that to 4 bytes and use new_encode_dev() for it.
We only use the 4-byte format if we _need_ to, if !old_valid_dev(foo).
This preserves backwards compatibility with older code as much as
possible. If we do make devices with major or minor numbers above 255, and
then mount the file system with the old code, it'll just read the first
two bytes and get the numbers wrong. If it comes to garbage-collect it,
it'll then write back those wrong numbers. But that's about the best we
can expect.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We have to pack at least the jint16_t structure, because otherwise it'll
be four bytes in size. Thankfully, we can do that and _not_ pack the
actual node structures, and the compiler still doesn't emit stupid code.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
We need to be able to have a "SPI bus 0" matching chip numbering; but
that number was wrongly used to flag dynamic allocation of a bus number.
This patch resolves that issue; now negative numbers trigger dynamic alloc.
It also updates the how-to-write-a-controller-driver overview to mention
this stuff.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add spi_device hook for LSB-first word encoding, and update all the
(in-tree) controller drivers to reject such devices. Eventually,
some controller drivers will be updated to support lsb-first encodings
on the wire; no current drivers need this.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Renamed bitbang_transfer_setup to follow convention of other exported symbols
from spi-bitbang. Exported spi_bitbang_setup_transfer to allow users of
spi-bitbang to use the function in their own setup_transfer.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This removes superfluous whitespace in the <linux/spi/spi.h> header.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver turns a PXA2xx synchronous serial port (SSP) into a SPI master
controller (see Documentation/spi/spi_summary). The driver has the following
features:
- Support for any PXA2xx SSP
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per slave device (chip) configuration.
- Full suspend, freeze, resume support.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some protocols (like one for some bitmap displays) require different clock
speed or word size settings for each transfer in an SPI message. This adds
those parameters to struct spi_transfer. They are to be used when they are
nonzero; otherwise the defaults from spi_device are to be used.
The patch also adds a setup_transfer callback to spi_bitbang, uses it for
messages that use those overrides, and implements it so that the pure
bitbanging code can help resolve any questions about how it should work.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Patch from Uwe Zeisberger
The symbol is only used in arch/arm/kernel/head-common.S. This in turn
is included from arch/arm/kernel/head.S and arch/arm/kernel/head-nommu.S
which include asm-offsets.h .
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
can_share_swap_page() is used to check if the page has the last reference.
This avoids allocating a new page for COW if it's the last page.
However, if CONFIG_SWAP is not set, can_share_swap_page() is defined as 0,
thus always causes a copy for the last COW page. The below simple patch
fixes it.
Signed-off-by: Hua Zhong <hzhong@gmail.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
slab_is_available() indicates slab based allocators are available for use.
SPARSEMEM code needs to know this as it can be called at various times
during the boot process.
Signed-off-by: Mike Kravetz <kravetz@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Even since a previous patch:
Fix race between CONFIG_DEBUG_SLABALLOC and modules
Sun, 27 Jun 2004 17:55:19 +0000 (17:55 +0000)
http://www.kernel.org/git/?p=linux/kernel/git/torvalds/old-2.6-bkcvs.git;a=commit;h=92b3db26d31cf21b70e3c1eadc56c179506d8fbe
The function symbol_put_addr() will deadlock the kernel.
symbol_put_addr() would acquire modlist_lock, then while holding the lock call
two functions kernel_text_address() and module_text_address() which also try
to acquire the same lock. This deadlocks the kernel of course.
This patch changes symbol_put_addr() to not acquire the modlist_lock, it
doesn't need it since it never looks at the module list directly. Also, it
now uses core_kernel_text() instead of kernel_text_address(). The latter has
an additional check for addr inside a module, but we don't need to do that
since we call module_text_address() (the same function kernel_text_address
uses) ourselves.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Cc: Zwane Mwaikambo <zwane@fsmlabs.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add new vmsplice system call and add missing __NR_xxx defines for
sys_set_robust_list, sys_get_robust_list, sys_splice, sys_sync_file_range
and sys_tee.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With "Paul E. McKenney" <paulmck@us.ibm.com>
Introduce rcu_needs_cpu() interface. This can be used to tell if there
will be a new rcu batch on a cpu soon by looking at the curlist pointer.
This can be used to avoid to enter a tickless idle state where the cpu
would miss that a new batch is ready when rcu_start_batch would be called
on a different cpu.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "Paul E. McKenney" <paulmck@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we use __attribute__((packed)), GCC will _also_ assume that the
structures aren't sensibly aligned, and it'll emit code to cope with
that instead of straight word load/save. This can be _very_ suboptimal
on architectures like ARM.
Ideally, we want an attribute which just tells GCC not to do any
padding, without the alignment side-effects. In the absense of that,
we'll just drop the 'packed' attribute and hope that everything stays as
it was (which to be fair is fairly much what we expect). And add some
paranoia checks in the initialisation code, which should be optimised
away completely in the normal case.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This attached patches provide xattr support including POSIX-ACL and
SELinux support on JFFS2 (version.5).
There are some significant differences from previous version posted
at last December.
The biggest change is addition of EBS(Erase Block Summary) support.
Currently, both kernel and usermode utility (sumtool) can recognize
xattr nodes which have JFFS2_NODETYPE_XATTR/_XREF nodetype.
In addition, some bugs are fixed.
- A potential race condition was fixed.
- Unexpected fail when updating a xattr by same name/value pair was fixed.
- A bug when removing xattr name/value pair was fixed.
The fundamental structures (such as using two new nodetypes and exclusion
mechanism by rwsem) are unchanged. But most of implementation were reviewed
and updated if necessary.
Espacially, we had to change several internal implementations related to
load_xattr_datum() to avoid a potential race condition.
[1/2] xattr_on_jffs2.kernel.version-5.patch
[2/2] xattr_on_jffs2.utils.version-5.patch
Signed-off-by: KaiGai Kohei <kaigai@ak.jp.nec.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
V4L1 API is depreciated and should be removed soon from kernel. This patch
adds two new options, one to disable V4L1 drivers, and another to disable
V4L1 compat module. This way, it would be easy to check what still depends
on V4L1 stuff, allowing also to test if app works fine with V4L2 only support.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The classical IP over ATM code maintains its own IPv4 <-> <ATM stuff>
ARP table, using the standard neighbour-table code. The
neigh_table_init function adds this neighbour table to a linked list
of all neighbor tables which is used by the functions neigh_delete()
neigh_add() and neightbl_set(), all called by the netlink code.
Once the ATM neighbour table is added to the list, there are two
tables with family == AF_INET there, and ARP entries sent via netlink
go into the first table with matching family. This is indeterminate
and often wrong.
To see the bug, on a kernel with CLIP enabled, create a standard IPv4
ARP entry by pinging an unused address on a local subnet. Then attempt
to complete that entry by doing
ip neigh replace <ip address> lladdr <some mac address> nud reachable
Looking at the ARP tables by using
ip neigh show
will reveal two ARP entries for the same address. One of these can be
found in /proc/net/arp, and the other in /proc/net/atm/arp.
This patch adds a new function, neigh_table_init_no_netlink() which
does everything the neigh_table_init() does, except add the table to
the netlink all-arp-tables chain. In addition neigh_table_init() has a
check that all tables on the chain have a distinct address family.
The init call in clip.c is changed to call
neigh_table_init_no_netlink().
Since ATM ARP tables are rather more complicated than can currently be
handled by the available rtattrs in the netlink protocol, no
functionality is lost by this patch, and non-ATM ARP manipulation via
netlink is rescued. A more complete solution would involve a rtattr
for ATM ARP entries and some way for the netlink code to give
neigh_add and friends more information than just address family with
which to find the correct ARP table.
[ I've changed the assertion checking in neigh_table_init() to not
use BUG_ON() while holding neigh_tbl_lock. Instead we remember that
we found an existing tbl with the same family, and after dropping
the lock we'll give a diagnostic kernel log message and a stack dump.
-DaveM ]
Signed-off-by: Simon Kelley <simon@thekelleys.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
One Block of the NAND Flash Array memory is reserved as
a One-Time Programmable Block memory area.
Also, 1st Block of NAND Flash Array can be used as OTP.
The OTP block can be read, programmed and locked using the same
operations as any other NAND Flash Array memory block.
OTP block cannot be erased.
OTP block is fully-guaranteed to be a valid block.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
* master.kernel.org:/home/rmk/linux-2.6-serial:
[SERIAL] 8250: add locking to console write function
[SERIAL] Remove unconditional enable of TX irq for console
[SERIAL] 8250: set divisor register correctly for AMD Alchemy SoC uart
[SERIAL] AMD Alchemy UART: claim memory range
[SERIAL] Clean up serial locking when obtaining a reference to a port
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET_SCHED]: HFSC: fix thinko in hfsc_adjust_levels()
[IPV6]: skb leakage in inet6_csk_xmit
[BRIDGE]: Do sysfs registration inside rtnl.
[NET]: Do sysfs registration as part of register_netdevice.
[TG3]: Fix possible NULL deref in tg3_run_loopback().
[NET] linkwatch: Handle jiffies wrap-around
[IRDA]: Switching to a workqueue for the SIR work
[IRDA]: smsc-ircc: Minimal hotplug support.
[IRDA]: Removing unused EXPORT_SYMBOLs
[IRDA]: New maintainer.
[NET]: Make netdev_chain a raw notifier.
[IPV4]: ip_options_fragment() has no effect on fragmentation
[NET]: Add missing operstates documentation.
The last step of netdevice registration was being done by a delayed
call, but because it was delayed, it was impossible to return any error
code if the class_device registration failed.
Side effects:
* one state in registration process is unnecessary.
* register_netdevice can sleep inside class_device registration/hotplug
* code in netdev_run_todo only does unregistration so it is simpler.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
debugged by Ming and Rohan:
The problem Ming and Rohan debugged was that during a normal session
login, open-iscsi is not incrementing the exp_statsn counter. It was
stuck at zero. From the RFC, it looks like if the login response PDU has
a successful status then we should be incrementing that value. Also from
the RFC, it looks like if when we drop a connection then reconnect, we
should be using the exp_statsn from the old connection in the next
relogin attempt.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
align printk output
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
add transport end point callbacks so iscsi drivers that cannot connect
from userspace, like iscsi tcp, using sockets do not have to
implement their own socket infrastructure.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/shemminger/netdev-2.6:
[PATCH] bcm43xx: Fix access to non-existent PHY registers
[PATCH] bcm43xx: Fix array overrun in bcm43xx_geo_init
[PATCH] bcm43xx: check for valid MAC address in SPROM
[PATCH] ieee80211: Fix A band channel count (resent)
[PATCH] bcm43xx: fix iwmode crash when down
[PATCH] softmac: make non-operational after being stopped
[PATCH] softmac: don't reassociate if user asked for deauthentication
spidernet: enable support for bcm5461 ethernet phy
spidernet: introduce new setting
Fix RTL8019AS init for Toshiba RBTX49xx boards
au1000_eth.c: use ether_crc() from <linux/crc32.h>
sky2: version 1.3
Add more support for the Yukon Ultra chip found in dual core centino laptops.
sky2: synchronize irq on remove
sky2: dont write status ring
sky2: edge triggered workaround enhancement
sky2: use mask instead of modulo operation
sky2: tx ring index mask fix
sky2: status irq hang fix
sky2: backout NAPI reschedule
My commit 6bfd93c32a broke the ARCH=ppc
compilation by using the is_kernel_addr() macro in asm/uaccess.h.
This fixes it by defining a suitable is_kernel_addr() for ARCH=ppc.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a backout of earlier patch.
The whole rescheduling hack was a bad idea. It doesn't really solve
the problem and it makes the code more complicated for no good reason.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Based on analysis&patch from Robert Hentosch
Observed on a Dell PE6850 with 16GB
The problem occurs very early on, when the kernel allocates space for the
temporary memory map called bootmap. The bootmap overlaps the EBDA region.
EBDA region is not historically reserved in the e820 mapping. When the
bootmap is freed it marks the EBDA region as usable.
If you notice in setup.c there is already code to work around the EBDA
in reserve_ebda_region(), this check however occurs after the bootmap
is allocated and doesn't prevent the bootmap from using this range.
AK: I redid the original patch. Thanks also to Jan Beulich for
spotting some mistakes.
Cc: Robert_Hentosch@dell.com
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device. The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided. Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up. The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices. The patch corrects this
problem by allowing PCI IRQs below 16.
Cc: len.brown@intel.com
Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also remove Bob Burroughs' email address, since it's no longer valid.
Acked-by: Eric D Rossman <edrossma@us.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Patch from Bellido Nicolas
Include hardware.h in debug-macro.S, otherwise io_p2v is undefined.
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Bellido Nicolas
Since git commit 2b78838842, entry-macro.S needs to include asm/arch/irqs.h
Signed-off-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch fixes the addruart macro to work with both mmu enabled and
disabled.
Signed-off-by: Sascha Hauer <s.hauer@pengutonix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After dwmw2 let me know it ought to be done, I rewrote the physmap map
driver to be a platform driver. I know zilch about the driver model,
so I probably botched it in some way, but I've done some tests on an
ixp23xx board which uses physmap, and it all seems to work.
In order to not break existing physmap users, I've added some compat
code that will instantiate a platform device iff CONFIG_MTD_PHYSMAP_LEN
is defined and != 0. Also, I've changed the default value for
CONFIG_MTD_PHYSMAP_LEN to zero, so that people who inadvertently
compile in physmap (or new, platform-style, users of physmap) don't get
burned.
This works pretty well -- the new physmap driver is a drop-in replacement
for the old one, and works on said ixp23xx board without any code changes
needed. (This should hold as long as users don't touch 'physmap_map'
directly.)
Once all physmap users have been converted to instantiate their own
platform devices, the compat code can go. (Or we decide that we can
change all the in-tree users at the same time, and never merge the
compat code.)
Signed-off-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Atomically create attributes when class device is added. This avoids
the race between registering class_device (which generates hotplug
event), and the creation of attribute groups.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend the support of attribute groups in class_device's to allow
groups to be created as part of the registration process. This allows
network device's to avoid race between registration and creating
groups.
Note that unlike attributes that are a property of the class object,
the groups are a property of the class_device object. This is done
because there are different types of network devices (wireless for
example).
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a deadlock situation in the receive path by allowing
temporary spillover of the receive buffer.
- If the chunk we receive has a tsn that immediately follows the ctsn,
accept it even if we run out of receive buffer space and renege data with
higher TSNs.
- Once we accept one chunk in a packet, accept all the remaining chunks
even if we run out of receive buffer space.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Mark Butler <butlerm@middle.net>
Acked-by: Vlad Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Nicolas Pitre
... but only for user space.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Nicolas Pitre
Intel PXA27x developers manual section 5.4.1.1 lists a priority
distribution for the DMA channels differently than what the code
currently assumes. This patch fixes that.
Noticed by Simon Vogl <vogl@soft.uni-linz.ac.at>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is the first step towards rate control inside softmac.
The txrates substructure has been extended to provide
different fields for different types of packets (management/data,
unicast/multicast). These fields are updated on association to values
compatible with the access point we are associating to.
Drivers can then use the new ieee80211softmac_suggest_txrate() function
call when deciding which rate to transmit each frame at. This is
immensely useful for ZD1211, and bcm can use it too.
The user can still specify a rate through iwconfig, which is matched
for all transmissions (assuming the rate they have specified is in
the rate set required by the AP).
At a later date, we can incorporate automatic rate management into
the ieee80211softmac_recalc_txrates() function.
This patch also removes the mcast_fallback field. Sam Leffler pointed
out that this field is meaningless, because no driver will ever be
retransmitting mcast frames (they are not acked).
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The channel count for 802.11a is still not right. We better
compute it from the min and max channel numbers, rather than
hardcoding it.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
zd1211 with softmac and wpa_supplicant revealed an issue with softmac
and the use of workqueues. Some of the work functions actually
reschedule themselves, so this meant that there could still be
pending work after flush_scheduled_work() had been called during
ieee80211softmac_stop().
This patch introduces a "running" flag which is used to ensure that
rescheduling does not happen in this situation.
I also used this flag to ensure that softmac's hooks into ieee80211 are
non-operational once the stop operation has been started. This simply
makes softmac a little more robust, because I could crash it easily
by receiving frames in the short timeframe after shutting down softmac
and before turning off the ZD1211 radio. (ZD1211 is now fixed as well!)
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
asm-ia64/bitops.h includes itself. The #ifndef _ASM_IA64_BITOPS_H
prevents this from being an issue, but it should still be removed.
Signed-off-by: Jon Mason <jdmason@us.ibm.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Patch from Nicolas Pitre
... for the definition of NULL.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] powerpc: Use the ibm,pa-features property if available
powerpc: Fix incorrect might_sleep in __get_user/__put_user on kernel addresses
[PATCH] ppc32 CPM_UART: fixes and improvements
[PATCH] ppc32 CPM_UART: Fixed break send on SCC
[PATCH] powerpc/kprobes: fix singlestep out-of-line
[PATCH] powerpc/pseries: avoid crash in PCI code if mem system not up
* master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] 3490/1: i.MX: move uart resources to board files
[ARM] 3488/1: make icedcc_putc do the right thing
[ARM] 3487/1: IXP4xx: Support non-PCI systems
[ARM] 3486/1: Mark memory as clobbered by the ARM _syscallX() macros
Patch from Sascha Hauer
This patch moves the i.MX uart resources and the gpio pin setup to the
board files. This allows the boards to decide how many internal uarts
are connected to the outside world and whether they use rts/cts or
not.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert all ROSE sysctl time values from jiffies to ms as units.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all NET/ROM sysctl time values from jiffies to ms as units.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert all AX.25 sysctl time values from jiffies to ms as units.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jing Min Zhao <zhaojingmin@users.sourceforge.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nick says that the current construct isn't safe. This goes back to the
original, but sets PIPE_BUF_FLAG_LRU on user pages as well as they all
seem to be on the LRU in the first place.
Signed-off-by: Jens Axboe <axboe@suse.de>
We have a case where __get_user and __put_user can validly be used
on kernel addresses in interrupt context - namely, the alignment
exception handler, as our get/put_unaligned just do a single access
and rely on the alignment exception handler to fix things up in the
rare cases where the cpu can't handle it in hardware. Thus we can
get alignment exceptions in the network stack at interrupt level.
The alignment exception handler does a __get_user to read the
instruction and blows up in might_sleep().
Since a __get_user on a kernel address won't actually ever sleep,
this makes the might_sleep conditional on the address being less
than PAGE_OFFSET.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A number of small issues are fixed, and added the header file, missed from the
original series. With this, driver should be pretty stable as tested among
both platform-device-driven and "old way" boards. Also added missing GPL
statement , and updated year field on existing ones to reflect
code update.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
SCC uart sends a break sequence each time it is stopped with the
CPM_CR_STOP_TX command. That means that each time an application closes the
serial device, a break is transmitted. To fix this, graceful tx stop is
issued for SCC.
Signed-off-by: David Jander <david.jander@protonic.nl>
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The CSD contains a "read2write factor" which determines the multiplier to
be applied to the read timeout to obtain the write timeout. We were
ignoring this parameter, resulting in the possibility for writes being
timed out too early.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently we rely on the PIPE_BUF_FLAG_LRU flag being set correctly
to know whether we need to fiddle with page LRU state after stealing it,
however for some origins we just don't know if the page is on the LRU
list or not.
So remove PIPE_BUF_FLAG_LRU and do this check/add manually in pipe_to_file()
instead.
Signed-off-by: Jens Axboe <axboe@suse.de>
* 'audit.b10' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/audit-current:
[PATCH] Audit Filter Performance
[PATCH] Rework of IPC auditing
[PATCH] More user space subject labels
[PATCH] Reworked patch for labels on user space messages
[PATCH] change lspp ipc auditing
[PATCH] audit inode patch
[PATCH] support for context based audit filtering, part 2
[PATCH] support for context based audit filtering
[PATCH] no need to wank with task_lock() and pinning task down in audit_syscall_exit()
[PATCH] drop task argument of audit_syscall_{entry,exit}
[PATCH] drop gfp_mask in audit_log_exit()
[PATCH] move call of audit_free() into do_exit()
[PATCH] sockaddr patch
[PATCH] deal with deadlocks in audit_free()
When iptables userspace adds an ipt_standard_target, it calculates the size
of the entire entry as:
sizeof(struct ipt_entry) + XT_ALIGN(sizeof(struct ipt_standard_target))
ipt_standard_target looks like this:
struct xt_standard_target
{
struct xt_entry_target target;
int verdict;
};
xt_entry_target contains a pointer, so when compiled for 64 bit the
structure gets an extra 4 byte of padding at the end. On 32 bit
architectures where iptables aligns to 8 byte it will also have 4
byte padding at the end because it is only 36 bytes large.
The compat_ipt_standard_fn in the kernel adjusts the offsets by
sizeof(struct ipt_standard_target) - sizeof(struct compat_ipt_standard_target),
which will always result in 4, even if the structure from userspace
was already padded to a multiple of 8. On x86 this works out by
accident because userspace only aligns to 4, on all other
architectures this is broken and causes incorrect adjustments to
the size and following offsets.
Thanks to Linus for lots of debugging help and testing.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* 'splice' of git://brick.kernel.dk/data/git/linux-2.6-block:
[PATCH] vmsplice: allow user to pass in gift pages
[PATCH] pipe: enable atomic copying of pipe data to/from user space
[PATCH] splice: call handle_ra_miss() on failure to lookup page
[PATCH] Add ->splice_read/splice_write to def_blk_fops
[PATCH] pipe: introduce ->pin() buffer operation
[PATCH] splice: fix bugs in pipe_to_file()
[PATCH] splice: fix bugs with stealing regular pipe pages
Add an nid member to the spu structure, and store the numa id of the spu there
on creation.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change of_node_to_nid() to traverse the device tree, looking for a numa id.
Cell uses this to assign ids to SPUs, which are children of the CPU node.
Existing users of of_node_to_nid() are altered to use of_node_to_nid_single(),
which doesn't do the traversal.
Export an attach_sysdev_to_node() function, allowing system devices (eg.
SPUs) to link themselves into the numa topology in sysfs.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If SPLICE_F_GIFT is set, the user is basically giving this pages away to
the kernel. That means we can steal them for eg page cache uses instead
of copying it.
The data must be properly page aligned and also a multiple of the page size
in length.
Signed-off-by: Jens Axboe <axboe@suse.de>
The pipe ->map() method uses kmap() to virtually map the pages, which
is both slow and has known scalability issues on SMP. This patch enables
atomic copying of pipe pages, by pre-faulting data and using kmap_atomic()
instead.
lmbench bw_pipe and lat_pipe measurements agree this is a Good Thing. Here
are results from that on a UP machine with highmem (1.5GiB of RAM), running
first a UP kernel, SMP kernel, and SMP kernel patched.
Vanilla-UP:
Pipe bandwidth: 1622.28 MB/sec
Pipe bandwidth: 1610.59 MB/sec
Pipe bandwidth: 1608.30 MB/sec
Pipe latency: 7.3275 microseconds
Pipe latency: 7.2995 microseconds
Pipe latency: 7.3097 microseconds
Vanilla-SMP:
Pipe bandwidth: 1382.19 MB/sec
Pipe bandwidth: 1317.27 MB/sec
Pipe bandwidth: 1355.61 MB/sec
Pipe latency: 9.6402 microseconds
Pipe latency: 9.6696 microseconds
Pipe latency: 9.6153 microseconds
Patched-SMP:
Pipe bandwidth: 1578.70 MB/sec
Pipe bandwidth: 1579.95 MB/sec
Pipe bandwidth: 1578.63 MB/sec
Pipe latency: 9.1654 microseconds
Pipe latency: 9.2266 microseconds
Pipe latency: 9.1527 microseconds
Signed-off-by: Jens Axboe <axboe@suse.de>
The ->map() function is really expensive on highmem machines right now,
since it has to use the slower kmap() instead of kmap_atomic(). Splice
rarely needs to access the virtual address of a page, so it's a waste
of time doing it.
Introduce ->pin() to take over the responsibility of making sure the
page data is valid. ->map() is then reduced to just kmap(). That way we
can also share a most of the pipe buffer ops between pipe.c and splice.c
Signed-off-by: Jens Axboe <axboe@suse.de>
Found by Oleg Nesterov <oleg@tv-sign.ru>, fixed by me.
- Only allow full pages to go to the page cache.
- Check page != buf->page instead of using PIPE_BUF_FLAG_STOLEN.
- Remember to clear 'stolen' if add_to_page_cache() fails.
And as a cleanup on that:
- Make the bottom fall-through logic a little less convoluted. Also make
the steal path hold an extra reference to the page, so we don't have
to differentiate between stolen and non-stolen at the end.
Signed-off-by: Jens Axboe <axboe@suse.de>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[TG3]: Update version and reldate
[TG3]: Fix bug in nvram write
[TG3]: Add reset_phy parameter to chip reset functions
[TG3]: Reset chip when changing MAC address
[TG3]: Add phy workaround
[TG3]: Call netif_carrier_off() during phy reset
[IPV6]: Fix race in route selection.
[XFRM]: fix incorrect xfrm_policy_afinfo_lock use
[XFRM]: fix incorrect xfrm_state_afinfo_lock use
[TCP]: Fix unlikely usage in tcp_transmit_skb()
[XFRM]: fix softirq-unsafe xfrm typemap->lock use
[IPSEC]: Fix IP ID selection
[NET]: use hlist_unhashed()
[IPV4]: inet_init() -> fs_initcall
[NETLINK]: cleanup unused macro in net/netlink/af_netlink.c
[PKT_SCHED] netem: fix loss
[X25]: fix for spinlock recurse and spinlock lockup with timer handler
* git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: make EVIOCGSND return meaningful data
Input: ressurect EVIOCGREP and EVIOCSREP
Input: psmouse - fix new device detection logic
Input: move input_device_id to mod_devicetable.h
Input: allow using several chords for braille
Input: allow passing NULL to input_free_device()
Input: spitzkbd - fix the reversed Address and Calender keys
Input: ads7846 - improve filtering for thumb press accuracy
Input: ads7846 - report 0 pressure value along with pen up event
Input: ads7846 - handle IRQs that were latched during disabled IRQs
Input: ads7846 - miscellaneous fixes
Input: ads7846 - use msleep() instead of udelay() in suspend
Input: ads7846 - debouncing and rudimentary sample filtering
Input: ads7846 - power down ADC a bit later
Input: ads7846 - add pen_down sysfs attribute
Input: wistron - add support for Fujitsu N3510
Input: wistron - add signature for Amilo M7400
* git://git.kernel.org/pub/scm/linux/kernel/git/perex/alsa: (22 commits)
[ALSA] via82xx - Use DXS_SRC as default for VIA8235/8237/8251 chips
[ALSA] hda-codec - Add model entry for ASUS Z62F
[ALSA] PCMCIA sound devices shouldn't depend on ISA
[ALSA] hda-codec - Fix capture from line-in on VAIO SZ/FE laptops
[ALSA] Fix Oops at rmmod with CONFIG_SND_VERBOSE_PROCFS=n
[ALSA] PCM core - introduce CONFIG_SND_PCM_XRUN_DEBUG
[ALSA] adding __devinitdata to pci_device_id
[ALSA] add __devinitdata to all pci_device_id
[ALSA] hda-codec - Add codec id for AD1988B codec chip
[ALSA] hda-codec - Add model entry for ASUS M9 laptop
[ALSA] pcxhr - Fix a compiler warning on 64bit architectures
[ALSA] via82xx: tweak VT8251 workaround
[ALSA] intel8x0 - Disable ALI5455 SPDIF-input
[ALSA] via82xx: add support for VIA VT8251 (AC'97)
[ALSA] Fix typos and add information about Jack support to Audiophile-Usb.txt
[ALSA] Fix double free in error path of miro driver
[ALSA] hda-codec - Add entry for Epox EP-5LDA+ GLi
[ALSA] sound/pci/: remove duplicate #include's
[ALSA] hda-codec - Use model 'hp' for all HP laptops with AD1981HD
[ALSA] continue on IS_ERR from platform device registration
...
1) The audit_ipc_perms() function has been split into two different
functions:
- audit_ipc_obj()
- audit_ipc_set_perm()
There's a key shift here... The audit_ipc_obj() collects the uid, gid,
mode, and SElinux context label of the current ipc object. This
audit_ipc_obj() hook is now found in several places. Most notably, it
is hooked in ipcperms(), which is called in various places around the
ipc code permforming a MAC check. Additionally there are several places
where *checkid() is used to validate that an operation is being
performed on a valid object while not necessarily having a nearby
ipcperms() call. In these locations, audit_ipc_obj() is called to
ensure that the information is captured by the audit system.
The audit_set_new_perm() function is called any time the permissions on
the ipc object changes. In this case, the NEW permissions are recorded
(and note that an audit_ipc_obj() call exists just a few lines before
each instance).
2) Support for an AUDIT_IPC_SET_PERM audit message type. This allows
for separate auxiliary audit records for normal operations on an IPC
object and permissions changes. Note that the same struct
audit_aux_data_ipcctl is used and populated, however there are separate
audit_log_format statements based on the type of the message. Finally,
the AUDIT_IPC block of code in audit_free_aux() was extended to handle
aux messages of this new type. No more mem leaks I hope ;-)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Hi,
The patch below builds upon the patch sent earlier and adds subject label to
all audit events generated via the netlink interface. It also cleans up a few
other minor things.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The below patch should be applied after the inode and ipc sid patches.
This patch is a reworking of Tim's patch that has been updated to match
the inode and ipc patches since its similar.
[updated:
> Stephen Smalley also wanted to change a variable from isec to tsec in the
> user sid patch. ]
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Hi,
The patch below converts IPC auditing to collect sid's and convert to context
string only if it needs to output an audit record. This patch depends on the
inode audit change patch already being applied.
Signed-off-by: Steve Grubb <sgrubb@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Previously, we were gathering the context instead of the sid. Now in this patch,
we gather just the sid and convert to context only if an audit event is being
output.
This patch brings the performance hit from 146% down to 23%
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The following patch provides selinux interfaces that will allow the audit
system to perform filtering based on the process context (user, role, type,
sensitivity, and clearance). These interfaces will allow the selinux
module to perform efficient matches based on lower level selinux constructs,
rather than relying on context retrievals and string comparisons within
the audit module. It also allows for dominance checks on the mls portion
of the contexts that are impossible with only string comparisons.
Signed-off-by: Darrel Goeddel <dgoeddel@trustedcs.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Patch from Deepak Saxena
This patch allows for the addition of IXP4xx systems that do not make
use of the PCI interface by moving the CONFIG_PCI symbol selection to
be platform-specific instead of for all of IXP4xx. If at least one machine
with PCI support is built, the PCI code will be compiled in, but when
building !PCI, this will drastically shrink the kernel size.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Markus Gutschke
In order to prevent gcc from making incorrect optimizations, all asm()
statements that define system calls should report memory as
clobbered. Recent versions of the headers for i386 have been changed
accordingly, but the ARM headers are still defective.
This patch fixes the bug tracked at
http://bugzilla.kernel.org/show_bug.cgi?id=6205
Signed-off-by: Markus Gutschke <markus@google.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The locking for the uart_port is over complicated, and can be
simplified if we introduce a flag to indicate that a port is "dead"
and will be removed.
This also helps the validator because it removes a case of non-nested
unlock ordering.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Use hlist_unhashed() rather than accessing inside data structure.
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The FXSAVE information leak patch introduced a bug in FP exception
handling: it clears FP exceptions only when there are already
none outstanding. Mikael Pettersson reported that causes problems
with the Erlang runtime and has tested this fix.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Acked-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While writing to an event device allows to set repeat rate for an
individual input device there is no way to retrieve current settings
so we need to ressurect EVIOCGREP. Also ressurect EVIOCSREP so we
have a symmetrical interface.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Add a cputable entry for the POWER6 processor.
The SIHV and SIPR bits in the mmcra have moved in POWER6, so disable
support for that until oprofile is fixed.
Also tell firmware that we know about POWER6.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
They shouldn't be using 'u32' et al in structures which are used for
communication with userspace. Switch to the proper types (__u32 etc).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
These aren't needed by glibc or klibc, and they're broken in some cases
anyway. The uClibc folks are apparently switching over to stop using
them too (now that we agreed that they should be dropped, at least).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
It uses kernel_ulong_t but can't be wrapped in __KERNEL__ because it's
used from scripts/mod/file2alias.c -- but we _can_ hide it inside
header manually too (and it doesn't generally exist for userspace).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add a read_mostly section and define __read_mostly to prevent cache line
pollution due to writes for mostly read variables. In addition fix the
incorrect alignment of the cache_line_aligned data section. s390 has a
cacheline size of 256 bytes.
Signed-off-by: Christian Borntraeger <cborntra@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for atomic futex operations.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add new SA_PROBEIRQ which suppresses the new sharing-mismatch warning.
Some drivers like to use request_irq() to find an unused interrupt slot.
- Use it in i82365.c
- Kill unused SA_PROBE.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Several structs in <scsi/srp.h> get padded to a multiple of 8 bytes on
64-bit architectures and end up with a size that does not match the
definition in the SRP spec:
SRP spec 64-bit
sizeof (struct indirect_buf) 20 24
sizeof (struct srp_login_rsp) 52 56
sizeof (struct srp_rsp) 36 40
Fix this by adding __attribute__((packed)) to the offending structs.
Problem pointed out by Arne Redlich <arne.redlich@xiranet.com>.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This consists of offsets fix in ..._devices.c, and update of
ppc_sys_fixup_mem_resource() function to prevent subsequent fixups
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Wire up *at syscalls.
This patch has been tested on ppc64 (using glibc's testsuite, both 32bit
and 64bit), and compile-tested for ppc32 (I have currently no ppc32 system
available, but I expect no problems).
Signed-off-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
